* [net-next 01/10] ewrk3/tulip: Move the DEC - Tulip drivers
2011-08-12 7:32 [net-next 00/10] drivers/net organize Ethernet drivers (4th series) Jeff Kirsher
@ 2011-08-12 7:32 ` Jeff Kirsher
2011-08-12 7:32 ` [net-next 02/10] ioc3-eth/meth: Move the SGI drivers Jeff Kirsher
` (9 subsequent siblings)
10 siblings, 0 replies; 21+ messages in thread
From: Jeff Kirsher @ 2011-08-12 7:32 UTC (permalink / raw)
To: davem
Cc: Jeff Kirsher, netdev, gospo, sassmann, Tobias Ringstrom,
Grant Grundler, David Davies
Move the DEC - Tulip driver into drivers/net/ethernet/dec/tulip/
and make the necessary Kconfig and Makefile changes.
The Digital Equioment (DEC) driver ewrk3 was moved into
drivers/net/ethernet/dec/ and the remaining drivers (Tulip)
were moved into drivers/net/ethernet/dec/tulip/
CC: Tobias Ringstrom <tori@unhappy.mine.nu>
CC: Grant Grundler <grundler@parisc-linux.org>
CC: David Davies <davies@maniac.ultranet.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Grant Grundler <grundler@parisc-linux.org>
---
MAINTAINERS | 4 +-
drivers/net/Kconfig | 16 ---------
drivers/net/Makefile | 2 -
drivers/net/ethernet/Kconfig | 1 +
drivers/net/ethernet/Makefile | 1 +
drivers/net/ethernet/dec/Kconfig | 36 ++++++++++++++++++++
drivers/net/ethernet/dec/Makefile | 6 +++
drivers/net/{ => ethernet/dec}/ewrk3.c | 0
drivers/net/{ => ethernet/dec}/ewrk3.h | 0
drivers/net/{ => ethernet/dec}/tulip/21142.c | 0
drivers/net/{ => ethernet/dec}/tulip/Kconfig | 20 +++++-----
drivers/net/{ => ethernet/dec}/tulip/Makefile | 0
drivers/net/{ => ethernet/dec}/tulip/de2104x.c | 0
drivers/net/{ => ethernet/dec}/tulip/de4x5.c | 0
drivers/net/{ => ethernet/dec}/tulip/de4x5.h | 0
drivers/net/{ => ethernet/dec}/tulip/dmfe.c | 0
drivers/net/{ => ethernet/dec}/tulip/eeprom.c | 0
drivers/net/{ => ethernet/dec}/tulip/interrupt.c | 0
drivers/net/{ => ethernet/dec}/tulip/media.c | 0
drivers/net/{ => ethernet/dec}/tulip/pnic.c | 0
drivers/net/{ => ethernet/dec}/tulip/pnic2.c | 0
drivers/net/{ => ethernet/dec}/tulip/timer.c | 0
drivers/net/{ => ethernet/dec}/tulip/tulip.h | 0
drivers/net/{ => ethernet/dec}/tulip/tulip_core.c | 0
drivers/net/{ => ethernet/dec}/tulip/uli526x.c | 0
drivers/net/{ => ethernet/dec}/tulip/winbond-840.c | 0
drivers/net/{ => ethernet/dec}/tulip/xircom_cb.c | 0
27 files changed, 56 insertions(+), 30 deletions(-)
create mode 100644 drivers/net/ethernet/dec/Kconfig
create mode 100644 drivers/net/ethernet/dec/Makefile
rename drivers/net/{ => ethernet/dec}/ewrk3.c (100%)
rename drivers/net/{ => ethernet/dec}/ewrk3.h (100%)
rename drivers/net/{ => ethernet/dec}/tulip/21142.c (100%)
rename drivers/net/{ => ethernet/dec}/tulip/Kconfig (96%)
rename drivers/net/{ => ethernet/dec}/tulip/Makefile (100%)
rename drivers/net/{ => ethernet/dec}/tulip/de2104x.c (100%)
rename drivers/net/{ => ethernet/dec}/tulip/de4x5.c (100%)
rename drivers/net/{ => ethernet/dec}/tulip/de4x5.h (100%)
rename drivers/net/{ => ethernet/dec}/tulip/dmfe.c (100%)
rename drivers/net/{ => ethernet/dec}/tulip/eeprom.c (100%)
rename drivers/net/{ => ethernet/dec}/tulip/interrupt.c (100%)
rename drivers/net/{ => ethernet/dec}/tulip/media.c (100%)
rename drivers/net/{ => ethernet/dec}/tulip/pnic.c (100%)
rename drivers/net/{ => ethernet/dec}/tulip/pnic2.c (100%)
rename drivers/net/{ => ethernet/dec}/tulip/timer.c (100%)
rename drivers/net/{ => ethernet/dec}/tulip/tulip.h (100%)
rename drivers/net/{ => ethernet/dec}/tulip/tulip_core.c (100%)
rename drivers/net/{ => ethernet/dec}/tulip/uli526x.c (100%)
rename drivers/net/{ => ethernet/dec}/tulip/winbond-840.c (100%)
rename drivers/net/{ => ethernet/dec}/tulip/xircom_cb.c (100%)
diff --git a/MAINTAINERS b/MAINTAINERS
index 26fa497..fbafbb6 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -2073,7 +2073,7 @@ DAVICOM FAST ETHERNET (DMFE) NETWORK DRIVER
L: netdev@vger.kernel.org
S: Orphan
F: Documentation/networking/dmfe.txt
-F: drivers/net/tulip/dmfe.c
+F: drivers/net/ethernet/tulip/dmfe.c
DC390/AM53C974 SCSI driver
M: Kurt Garloff <garloff@suse.de>
@@ -6514,7 +6514,7 @@ TULIP NETWORK DRIVERS
M: Grant Grundler <grundler@parisc-linux.org>
L: netdev@vger.kernel.org
S: Maintained
-F: drivers/net/tulip/
+F: drivers/net/ethernet/tulip/
TUN/TAP driver
M: Maxim Krasnyansky <maxk@qualcomm.com>
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index c8779c1..0cb136c 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -452,8 +452,6 @@ config DNET
To compile this driver as a module, choose M here: the module
will be called dnet.
-source "drivers/net/tulip/Kconfig"
-
config AT1700
tristate "AT1700/1720 support (EXPERIMENTAL)"
depends on (ISA || MCA_LEGACY) && EXPERIMENTAL
@@ -494,20 +492,6 @@ config NET_ISA
the remaining ISA network card questions. If you say Y, you will be
asked for your specific card in the following questions.
-config EWRK3
- tristate "EtherWORKS 3 (DE203, DE204, DE205) support"
- depends on NET_ISA
- select CRC32
- ---help---
- This driver supports the DE203, DE204 and DE205 network (Ethernet)
- cards. If this is for you, say Y and read
- <file:Documentation/networking/ewrk3.txt> in the kernel source as
- well as the Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>.
-
- To compile this driver as a module, choose M here. The module
- will be called ewrk3.
-
config ETH16I
tristate "ICL EtherTeam 16i/32 support"
depends on NET_ISA
diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index db888b0..8a56733 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -106,7 +106,6 @@ obj-$(CONFIG_SGISEEQ) += sgiseeq.o
obj-$(CONFIG_SGI_O2MACE_ETH) += meth.o
obj-$(CONFIG_AT1700) += at1700.o
obj-$(CONFIG_CPMAC) += cpmac.o
-obj-$(CONFIG_EWRK3) += ewrk3.o
obj-$(CONFIG_ETH16I) += eth16i.o
obj-$(CONFIG_EQUALIZER) += eql.o
@@ -147,7 +146,6 @@ obj-$(CONFIG_USB_IPHETH) += usb/
obj-$(CONFIG_USB_CDC_PHONET) += usb/
obj-$(CONFIG_WLAN) += wireless/
-obj-$(CONFIG_NET_TULIP) += tulip/
obj-$(CONFIG_HAMRADIO) += hamradio/
obj-$(CONFIG_IRDA) += irda/
obj-$(CONFIG_ETRAX_ETHERNET) += cris/
diff --git a/drivers/net/ethernet/Kconfig b/drivers/net/ethernet/Kconfig
index 9410f20..ed42850 100644
--- a/drivers/net/ethernet/Kconfig
+++ b/drivers/net/ethernet/Kconfig
@@ -19,6 +19,7 @@ source "drivers/net/ethernet/broadcom/Kconfig"
source "drivers/net/ethernet/brocade/Kconfig"
source "drivers/net/ethernet/chelsio/Kconfig"
source "drivers/net/ethernet/cisco/Kconfig"
+source "drivers/net/ethernet/dec/Kconfig"
source "drivers/net/ethernet/dlink/Kconfig"
source "drivers/net/ethernet/emulex/Kconfig"
source "drivers/net/ethernet/neterion/Kconfig"
diff --git a/drivers/net/ethernet/Makefile b/drivers/net/ethernet/Makefile
index 5d89fd9..3de8249 100644
--- a/drivers/net/ethernet/Makefile
+++ b/drivers/net/ethernet/Makefile
@@ -11,6 +11,7 @@ obj-$(CONFIG_NET_VENDOR_BROADCOM) += broadcom/
obj-$(CONFIG_NET_VENDOR_BROCADE) += brocade/
obj-$(CONFIG_NET_VENDOR_CHELSIO) += chelsio/
obj-$(CONFIG_NET_VENDOR_CISCO) += cisco/
+obj-$(CONFIG_NET_VENDOR_DEC) += dec/
obj-$(CONFIG_NET_VENDOR_DLINK) += dlink/
obj-$(CONFIG_NET_VENDOR_EMULEX) += emulex/
obj-$(CONFIG_NET_VENDOR_EXAR) += neterion/
diff --git a/drivers/net/ethernet/dec/Kconfig b/drivers/net/ethernet/dec/Kconfig
new file mode 100644
index 0000000..40e8df9
--- /dev/null
+++ b/drivers/net/ethernet/dec/Kconfig
@@ -0,0 +1,36 @@
+#
+# Digital Equipment Inc network device configuration
+#
+
+config NET_VENDOR_DEC
+ bool "Digital Equipment devices"
+ depends on PCI || EISA || CARDBUS
+ ---help---
+ If you have a network (Ethernet) card belonging to this class, say Y
+ and read the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>.
+
+ Note that the answer to this question doesn't directly affect the
+ kernel: saying N will just cause the configurator to skip all
+ the questions about DEC cards. If you say Y, you will be asked for
+ your specific card in the following questions.
+
+if NET_VENDOR_DEC
+
+config EWRK3
+ tristate "EtherWORKS 3 (DE203, DE204, DE205) support"
+ depends on ISA
+ select CRC32
+ ---help---
+ This driver supports the DE203, DE204 and DE205 network (Ethernet)
+ cards. If this is for you, say Y and read
+ <file:Documentation/networking/ewrk3.txt> in the kernel source as
+ well as the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>.
+
+ To compile this driver as a module, choose M here. The module
+ will be called ewrk3.
+
+source "drivers/net/ethernet/dec/tulip/Kconfig"
+
+endif # NET_VENDOR_DEC
diff --git a/drivers/net/ethernet/dec/Makefile b/drivers/net/ethernet/dec/Makefile
new file mode 100644
index 0000000..1b01ed8
--- /dev/null
+++ b/drivers/net/ethernet/dec/Makefile
@@ -0,0 +1,6 @@
+#
+# Makefile for the Digital Equipment Inc. network device drivers.
+#
+
+obj-$(CONFIG_EWRK3) += ewrk3.o
+obj-$(CONFIG_NET_TULIP) += tulip/
diff --git a/drivers/net/ewrk3.c b/drivers/net/ethernet/dec/ewrk3.c
similarity index 100%
rename from drivers/net/ewrk3.c
rename to drivers/net/ethernet/dec/ewrk3.c
diff --git a/drivers/net/ewrk3.h b/drivers/net/ethernet/dec/ewrk3.h
similarity index 100%
rename from drivers/net/ewrk3.h
rename to drivers/net/ethernet/dec/ewrk3.h
diff --git a/drivers/net/tulip/21142.c b/drivers/net/ethernet/dec/tulip/21142.c
similarity index 100%
rename from drivers/net/tulip/21142.c
rename to drivers/net/ethernet/dec/tulip/21142.c
diff --git a/drivers/net/tulip/Kconfig b/drivers/net/ethernet/dec/tulip/Kconfig
similarity index 96%
rename from drivers/net/tulip/Kconfig
rename to drivers/net/ethernet/dec/tulip/Kconfig
index 1f8d4a8..f6af772 100644
--- a/drivers/net/tulip/Kconfig
+++ b/drivers/net/ethernet/dec/tulip/Kconfig
@@ -2,10 +2,10 @@
# Tulip family network device configuration
#
-menuconfig NET_TULIP
- bool "\"Tulip\" family network device support"
- depends on PCI || EISA || CARDBUS
- help
+config NET_TULIP
+ bool "DEC - Tulip devices"
+ depends on (PCI || EISA || CARDBUS)
+ ---help---
This selects the "Tulip" family of EISA/PCI network cards.
if NET_TULIP
@@ -32,7 +32,7 @@ config DE2104X_DSL
depends on DE2104X
range 0 31
default 0
- help
+ ---help---
Setting this value allows to align ring buffer descriptors into their
own cache lines. Value of 4 corresponds to the typical 32 byte line
(the descriptor is 16 bytes). This is necessary on systems that lack
@@ -59,7 +59,7 @@ config TULIP
config TULIP_MWI
bool "New bus configuration (EXPERIMENTAL)"
depends on TULIP && EXPERIMENTAL
- help
+ ---help---
This configures your Tulip card specifically for the card and
system cache line size type you are using.
@@ -70,7 +70,7 @@ config TULIP_MWI
config TULIP_MMIO
bool "Use PCI shared mem for NIC registers"
depends on TULIP
- help
+ ---help---
Use PCI shared memory for the NIC registers, rather than going through
the Tulip's PIO (programmed I/O ports). Faster, but could produce
obscure bugs if your mainboard has memory controller timing issues.
@@ -79,7 +79,7 @@ config TULIP_MMIO
config TULIP_NAPI
bool "Use RX polling (NAPI)"
depends on TULIP
- help
+ ---help---
NAPI is a new driver API designed to reduce CPU and interrupt load
when the driver is receiving lots of packets from the card. It is
still somewhat experimental and thus not yet enabled by default.
@@ -107,7 +107,7 @@ config TULIP_DM910X
config DE4X5
tristate "Generic DECchip & DIGITAL EtherWORKS PCI/EISA"
- depends on PCI || EISA
+ depends on (PCI || EISA)
select CRC32
---help---
This is support for the DIGITAL series of PCI/EISA Ethernet cards.
@@ -126,7 +126,7 @@ config WINBOND_840
depends on PCI
select CRC32
select MII
- help
+ ---help---
This driver is for the Winbond W89c840 chip. It also works with
the TX9882 chip on the Compex RL100-ATX board.
More specific information and updates are available from
diff --git a/drivers/net/tulip/Makefile b/drivers/net/ethernet/dec/tulip/Makefile
similarity index 100%
rename from drivers/net/tulip/Makefile
rename to drivers/net/ethernet/dec/tulip/Makefile
diff --git a/drivers/net/tulip/de2104x.c b/drivers/net/ethernet/dec/tulip/de2104x.c
similarity index 100%
rename from drivers/net/tulip/de2104x.c
rename to drivers/net/ethernet/dec/tulip/de2104x.c
diff --git a/drivers/net/tulip/de4x5.c b/drivers/net/ethernet/dec/tulip/de4x5.c
similarity index 100%
rename from drivers/net/tulip/de4x5.c
rename to drivers/net/ethernet/dec/tulip/de4x5.c
diff --git a/drivers/net/tulip/de4x5.h b/drivers/net/ethernet/dec/tulip/de4x5.h
similarity index 100%
rename from drivers/net/tulip/de4x5.h
rename to drivers/net/ethernet/dec/tulip/de4x5.h
diff --git a/drivers/net/tulip/dmfe.c b/drivers/net/ethernet/dec/tulip/dmfe.c
similarity index 100%
rename from drivers/net/tulip/dmfe.c
rename to drivers/net/ethernet/dec/tulip/dmfe.c
diff --git a/drivers/net/tulip/eeprom.c b/drivers/net/ethernet/dec/tulip/eeprom.c
similarity index 100%
rename from drivers/net/tulip/eeprom.c
rename to drivers/net/ethernet/dec/tulip/eeprom.c
diff --git a/drivers/net/tulip/interrupt.c b/drivers/net/ethernet/dec/tulip/interrupt.c
similarity index 100%
rename from drivers/net/tulip/interrupt.c
rename to drivers/net/ethernet/dec/tulip/interrupt.c
diff --git a/drivers/net/tulip/media.c b/drivers/net/ethernet/dec/tulip/media.c
similarity index 100%
rename from drivers/net/tulip/media.c
rename to drivers/net/ethernet/dec/tulip/media.c
diff --git a/drivers/net/tulip/pnic.c b/drivers/net/ethernet/dec/tulip/pnic.c
similarity index 100%
rename from drivers/net/tulip/pnic.c
rename to drivers/net/ethernet/dec/tulip/pnic.c
diff --git a/drivers/net/tulip/pnic2.c b/drivers/net/ethernet/dec/tulip/pnic2.c
similarity index 100%
rename from drivers/net/tulip/pnic2.c
rename to drivers/net/ethernet/dec/tulip/pnic2.c
diff --git a/drivers/net/tulip/timer.c b/drivers/net/ethernet/dec/tulip/timer.c
similarity index 100%
rename from drivers/net/tulip/timer.c
rename to drivers/net/ethernet/dec/tulip/timer.c
diff --git a/drivers/net/tulip/tulip.h b/drivers/net/ethernet/dec/tulip/tulip.h
similarity index 100%
rename from drivers/net/tulip/tulip.h
rename to drivers/net/ethernet/dec/tulip/tulip.h
diff --git a/drivers/net/tulip/tulip_core.c b/drivers/net/ethernet/dec/tulip/tulip_core.c
similarity index 100%
rename from drivers/net/tulip/tulip_core.c
rename to drivers/net/ethernet/dec/tulip/tulip_core.c
diff --git a/drivers/net/tulip/uli526x.c b/drivers/net/ethernet/dec/tulip/uli526x.c
similarity index 100%
rename from drivers/net/tulip/uli526x.c
rename to drivers/net/ethernet/dec/tulip/uli526x.c
diff --git a/drivers/net/tulip/winbond-840.c b/drivers/net/ethernet/dec/tulip/winbond-840.c
similarity index 100%
rename from drivers/net/tulip/winbond-840.c
rename to drivers/net/ethernet/dec/tulip/winbond-840.c
diff --git a/drivers/net/tulip/xircom_cb.c b/drivers/net/ethernet/dec/tulip/xircom_cb.c
similarity index 100%
rename from drivers/net/tulip/xircom_cb.c
rename to drivers/net/ethernet/dec/tulip/xircom_cb.c
--
1.7.6
^ permalink raw reply related [flat|nested] 21+ messages in thread* [net-next 02/10] ioc3-eth/meth: Move the SGI drivers
2011-08-12 7:32 [net-next 00/10] drivers/net organize Ethernet drivers (4th series) Jeff Kirsher
2011-08-12 7:32 ` [net-next 01/10] ewrk3/tulip: Move the DEC - Tulip drivers Jeff Kirsher
@ 2011-08-12 7:32 ` Jeff Kirsher
2011-08-18 19:46 ` Ralf Baechle
2011-08-12 7:32 ` [net-next 03/10] seeq: Move the SEEQ drivers Jeff Kirsher
` (8 subsequent siblings)
10 siblings, 1 reply; 21+ messages in thread
From: Jeff Kirsher @ 2011-08-12 7:32 UTC (permalink / raw)
To: davem; +Cc: Jeff Kirsher, netdev, gospo, sassmann, Ralf Baechle
Move the SGI drivers into drivers/net/ethernet/sgi/ and make the
necessary Kconfig and Makefile changes.
CC: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
MAINTAINERS | 2 +-
drivers/net/Kconfig | 14 ------------
drivers/net/Makefile | 2 -
drivers/net/ethernet/Kconfig | 1 +
drivers/net/ethernet/Makefile | 1 +
drivers/net/ethernet/sgi/Kconfig | 34 +++++++++++++++++++++++++++++
drivers/net/ethernet/sgi/Makefile | 6 +++++
drivers/net/{ => ethernet/sgi}/ioc3-eth.c | 0
drivers/net/{ => ethernet/sgi}/meth.c | 0
drivers/net/{ => ethernet/sgi}/meth.h | 0
10 files changed, 43 insertions(+), 17 deletions(-)
create mode 100644 drivers/net/ethernet/sgi/Kconfig
create mode 100644 drivers/net/ethernet/sgi/Makefile
rename drivers/net/{ => ethernet/sgi}/ioc3-eth.c (100%)
rename drivers/net/{ => ethernet/sgi}/meth.c (100%)
rename drivers/net/{ => ethernet/sgi}/meth.h (100%)
diff --git a/MAINTAINERS b/MAINTAINERS
index fbafbb6..1bd9fbd 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -3424,7 +3424,7 @@ IOC3 ETHERNET DRIVER
M: Ralf Baechle <ralf@linux-mips.org>
L: linux-mips@linux-mips.org
S: Maintained
-F: drivers/net/ioc3-eth.c
+F: drivers/net/ethernet/sgi/ioc3-eth.c
IOC3 SERIAL DRIVER
M: Pat Gefre <pfg@sgi.com>
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index 0cb136c..aec74ad 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -244,16 +244,6 @@ config KORINA
If you have a Mikrotik RouterBoard 500 or IDT RC32434
based system say Y. Otherwise say N.
-config SGI_IOC3_ETH
- bool "SGI IOC3 Ethernet"
- depends on PCI && SGI_IP27
- select CRC32
- select MII
- help
- If you have a network (Ethernet) card of this type, say Y and read
- the Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>.
-
config MIPS_SIM_NET
tristate "MIPS simulator Network device"
depends on MIPS_SIM
@@ -262,10 +252,6 @@ config MIPS_SIM_NET
emulated by the MIPS Simulator.
If you are not using a MIPSsim or are unsure, say N.
-config SGI_O2MACE_ETH
- tristate "SGI O2 MACE Fast Ethernet support"
- depends on SGI_IP32=y
-
config SH_ETH
tristate "Renesas SuperH Ethernet support"
depends on SUPERH && \
diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index 8a56733..c98e1ad 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -103,7 +103,6 @@ obj-$(CONFIG_MACVLAN) += macvlan.o
obj-$(CONFIG_MACVTAP) += macvtap.o
obj-$(CONFIG_DEFXX) += defxx.o
obj-$(CONFIG_SGISEEQ) += sgiseeq.o
-obj-$(CONFIG_SGI_O2MACE_ETH) += meth.o
obj-$(CONFIG_AT1700) += at1700.o
obj-$(CONFIG_CPMAC) += cpmac.o
@@ -111,7 +110,6 @@ obj-$(CONFIG_ETH16I) += eth16i.o
obj-$(CONFIG_EQUALIZER) += eql.o
obj-$(CONFIG_KORINA) += korina.o
obj-$(CONFIG_MIPS_SIM_NET) += mipsnet.o
-obj-$(CONFIG_SGI_IOC3_ETH) += ioc3-eth.o
obj-$(CONFIG_TUN) += tun.o
obj-$(CONFIG_VETH) += veth.o
obj-$(CONFIG_NET_NETX) += netx-eth.o
diff --git a/drivers/net/ethernet/Kconfig b/drivers/net/ethernet/Kconfig
index ed42850..7d25fa4 100644
--- a/drivers/net/ethernet/Kconfig
+++ b/drivers/net/ethernet/Kconfig
@@ -37,6 +37,7 @@ source "drivers/net/ethernet/qlogic/Kconfig"
source "drivers/net/ethernet/racal/Kconfig"
source "drivers/net/ethernet/realtek/Kconfig"
source "drivers/net/ethernet/sfc/Kconfig"
+source "drivers/net/ethernet/sgi/Kconfig"
source "drivers/net/ethernet/smsc/Kconfig"
source "drivers/net/ethernet/stmicro/Kconfig"
source "drivers/net/ethernet/sun/Kconfig"
diff --git a/drivers/net/ethernet/Makefile b/drivers/net/ethernet/Makefile
index 3de8249..ec58715 100644
--- a/drivers/net/ethernet/Makefile
+++ b/drivers/net/ethernet/Makefile
@@ -28,6 +28,7 @@ obj-$(CONFIG_NET_VENDOR_QLOGIC) += qlogic/
obj-$(CONFIG_NET_VENDOR_RACAL) += racal/
obj-$(CONFIG_NET_VENDOR_REALTEK) += realtek/
obj-$(CONFIG_SFC) += sfc/
+obj-$(CONFIG_NET_VENDOR_SGI) += sgi/
obj-$(CONFIG_NET_VENDOR_SMSC) += smsc/
obj-$(CONFIG_NET_VENDOR_STMICRO) += stmicro/
obj-$(CONFIG_NET_VENDOR_SUN) += sun/
diff --git a/drivers/net/ethernet/sgi/Kconfig b/drivers/net/ethernet/sgi/Kconfig
new file mode 100644
index 0000000..3098594
--- /dev/null
+++ b/drivers/net/ethernet/sgi/Kconfig
@@ -0,0 +1,34 @@
+#
+# SGI device configuration
+#
+
+config NET_VENDOR_SGI
+ bool "SGI devices"
+ depends on (PCI && SGI_IP27) || SGI_IP32
+ ---help---
+ If you have a network (Ethernet) card belonging to this class, say Y
+ and read the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>.
+
+ Note that the answer to this question doesn't directly affect the
+ kernel: saying N will just cause the configurator to skip all
+ the questions about SGI devices. If you say Y, you will be asked for
+ your specific card in the following questions.
+
+if NET_VENDOR_SGI
+
+config SGI_IOC3_ETH
+ bool "SGI IOC3 Ethernet"
+ depends on PCI && SGI_IP27
+ select CRC32
+ select MII
+ ---help---
+ If you have a network (Ethernet) card of this type, say Y and read
+ the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>.
+
+config SGI_O2MACE_ETH
+ tristate "SGI O2 MACE Fast Ethernet support"
+ depends on SGI_IP32=y
+
+endif # NET_VENDOR_SGI
diff --git a/drivers/net/ethernet/sgi/Makefile b/drivers/net/ethernet/sgi/Makefile
new file mode 100644
index 0000000..e5bedd2
--- /dev/null
+++ b/drivers/net/ethernet/sgi/Makefile
@@ -0,0 +1,6 @@
+#
+# Makefile for the SGI device drivers.
+#
+
+obj-$(CONFIG_SGI_O2MACE_ETH) += meth.o
+obj-$(CONFIG_SGI_IOC3_ETH) += ioc3-eth.o
diff --git a/drivers/net/ioc3-eth.c b/drivers/net/ethernet/sgi/ioc3-eth.c
similarity index 100%
rename from drivers/net/ioc3-eth.c
rename to drivers/net/ethernet/sgi/ioc3-eth.c
diff --git a/drivers/net/meth.c b/drivers/net/ethernet/sgi/meth.c
similarity index 100%
rename from drivers/net/meth.c
rename to drivers/net/ethernet/sgi/meth.c
diff --git a/drivers/net/meth.h b/drivers/net/ethernet/sgi/meth.h
similarity index 100%
rename from drivers/net/meth.h
rename to drivers/net/ethernet/sgi/meth.h
--
1.7.6
^ permalink raw reply related [flat|nested] 21+ messages in thread* Re: [net-next 02/10] ioc3-eth/meth: Move the SGI drivers
2011-08-12 7:32 ` [net-next 02/10] ioc3-eth/meth: Move the SGI drivers Jeff Kirsher
@ 2011-08-18 19:46 ` Ralf Baechle
0 siblings, 0 replies; 21+ messages in thread
From: Ralf Baechle @ 2011-08-18 19:46 UTC (permalink / raw)
To: Jeff Kirsher; +Cc: davem, netdev, gospo, sassmann
On Fri, Aug 12, 2011 at 12:32:56AM -0700, Jeff Kirsher wrote:
> diff --git a/drivers/net/ethernet/sgi/Kconfig b/drivers/net/ethernet/sgi/Kconfig
> new file mode 100644
> index 0000000..3098594
> --- /dev/null
> +++ b/drivers/net/ethernet/sgi/Kconfig
> @@ -0,0 +1,34 @@
> +#
> +# SGI device configuration
> +#
> +
> +config NET_VENDOR_SGI
> + bool "SGI devices"
> + depends on (PCI && SGI_IP27) || SGI_IP32
Can you make NET_VENDOR_SGI default to y for these systems? There is
normally no reason other than maybe testing to ever disable NET_VENDOR_SGI
as these NICs are all on the motherboard.
Otherwise ok. Thanks,
Ralf
^ permalink raw reply [flat|nested] 21+ messages in thread
* [net-next 03/10] seeq: Move the SEEQ drivers
2011-08-12 7:32 [net-next 00/10] drivers/net organize Ethernet drivers (4th series) Jeff Kirsher
2011-08-12 7:32 ` [net-next 01/10] ewrk3/tulip: Move the DEC - Tulip drivers Jeff Kirsher
2011-08-12 7:32 ` [net-next 02/10] ioc3-eth/meth: Move the SGI drivers Jeff Kirsher
@ 2011-08-12 7:32 ` Jeff Kirsher
2011-08-18 19:36 ` Ralf Baechle
2011-11-04 17:24 ` Russell King - ARM Linux
2011-08-12 7:32 ` [net-next 04/10] pch_gbe: Move the OKI Semiconductor driver Jeff Kirsher
` (7 subsequent siblings)
10 siblings, 2 replies; 21+ messages in thread
From: Jeff Kirsher @ 2011-08-12 7:32 UTC (permalink / raw)
To: davem; +Cc: Jeff Kirsher, netdev, gospo, sassmann, Russell King,
Hamish Coleman
Move the drivers that use SEEQ chipset into drivers/net/ethernet/seeq
and make the necessary Kconfig and Makefile changes.
CC: Russell King <linux@arm.linux.org.uk>
CC: Hamish Coleman <hamish@zot.apana.org.au>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
MAINTAINERS | 3 +-
drivers/net/Kconfig | 18 -----------
drivers/net/Makefile | 2 -
drivers/net/arm/Kconfig | 7 ----
drivers/net/arm/Makefile | 1 -
drivers/net/ethernet/Kconfig | 1 +
drivers/net/ethernet/Makefile | 1 +
drivers/net/ethernet/seeq/Kconfig | 45 +++++++++++++++++++++++++++
drivers/net/ethernet/seeq/Makefile | 7 ++++
drivers/net/{arm => ethernet/seeq}/ether3.c | 0
drivers/net/{arm => ethernet/seeq}/ether3.h | 0
drivers/net/{ => ethernet/seeq}/seeq8005.c | 0
drivers/net/{ => ethernet/seeq}/seeq8005.h | 0
drivers/net/{ => ethernet/seeq}/sgiseeq.c | 0
drivers/net/{ => ethernet/seeq}/sgiseeq.h | 0
15 files changed, 56 insertions(+), 29 deletions(-)
create mode 100644 drivers/net/ethernet/seeq/Kconfig
create mode 100644 drivers/net/ethernet/seeq/Makefile
rename drivers/net/{arm => ethernet/seeq}/ether3.c (100%)
rename drivers/net/{arm => ethernet/seeq}/ether3.h (100%)
rename drivers/net/{ => ethernet/seeq}/seeq8005.c (100%)
rename drivers/net/{ => ethernet/seeq}/seeq8005.h (100%)
rename drivers/net/{ => ethernet/seeq}/sgiseeq.c (100%)
rename drivers/net/{ => ethernet/seeq}/sgiseeq.h (100%)
diff --git a/MAINTAINERS b/MAINTAINERS
index 1bd9fbd..e986e3e 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1014,7 +1014,8 @@ F: arch/arm/include/asm/hardware/ioc.h
F: arch/arm/include/asm/hardware/iomd.h
F: arch/arm/include/asm/hardware/memc.h
F: arch/arm/mach-rpc/
-F: drivers/net/arm/ether3*
+F: drivers/net/ethernet/i825xx/ether1*
+F: drivers/net/ethernet/seeq/ether3*
F: drivers/scsi/arm/
ARM/SHARK MACHINE SUPPORT
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index aec74ad..696464c 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -489,17 +489,6 @@ config ETH16I
To compile this driver as a module, choose M here. The module
will be called eth16i.
-config SEEQ8005
- tristate "SEEQ8005 support (EXPERIMENTAL)"
- depends on NET_ISA && EXPERIMENTAL
- help
- This is a driver for the SEEQ 8005 network (Ethernet) card. If this
- is for you, read the Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>.
-
- To compile this driver as a module, choose M here. The module
- will be called seeq8005.
-
config NET_PCI
bool "EISA, VLB, PCI and on board controllers"
depends on ISA || EISA || PCI
@@ -690,13 +679,6 @@ config NET_POCKET
the questions about this class of network devices. If you say Y, you
will be asked for your specific device in the following questions.
-config SGISEEQ
- tristate "SGI Seeq ethernet controller support"
- depends on SGI_HAS_SEEQ
- help
- Say Y here if you have an Seeq based Ethernet network card. This is
- used in many Silicon Graphics machines.
-
config FEC
bool "FEC ethernet controller (of ColdFire and some i.MX CPUs)"
depends on M523x || M527x || M5272 || M528x || M520x || M532x || \
diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index c98e1ad..b1ead87 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -65,7 +65,6 @@ obj-$(CONFIG_SH_ETH) += sh_eth.o
obj-$(CONFIG_HAMACHI) += hamachi.o
obj-$(CONFIG_NET) += Space.o loopback.o
-obj-$(CONFIG_SEEQ8005) += seeq8005.o
obj-$(CONFIG_NET_SB1000) += sb1000.o
obj-$(CONFIG_HP100) += hp100.o
obj-$(CONFIG_FEC) += fec.o
@@ -102,7 +101,6 @@ obj-$(CONFIG_IFB) += ifb.o
obj-$(CONFIG_MACVLAN) += macvlan.o
obj-$(CONFIG_MACVTAP) += macvtap.o
obj-$(CONFIG_DEFXX) += defxx.o
-obj-$(CONFIG_SGISEEQ) += sgiseeq.o
obj-$(CONFIG_AT1700) += at1700.o
obj-$(CONFIG_CPMAC) += cpmac.o
diff --git a/drivers/net/arm/Kconfig b/drivers/net/arm/Kconfig
index 4320e88..b6f7302 100644
--- a/drivers/net/arm/Kconfig
+++ b/drivers/net/arm/Kconfig
@@ -3,13 +3,6 @@
# These are for Acorn's Expansion card network interfaces
#
-config ARM_ETHER3
- tristate "Acorn/ANT Ether3 support"
- depends on ARM && ARCH_ACORN
- help
- If you have an Acorn system with one of these network cards, you
- should say Y to this option if you wish to use it with Linux.
-
config ARM_AT91_ETHER
tristate "AT91RM9200 Ethernet support"
depends on ARM && ARCH_AT91RM9200
diff --git a/drivers/net/arm/Makefile b/drivers/net/arm/Makefile
index 5a0f141..a2532e6 100644
--- a/drivers/net/arm/Makefile
+++ b/drivers/net/arm/Makefile
@@ -3,7 +3,6 @@
# Makefile for the ARM network device drivers
#
-obj-$(CONFIG_ARM_ETHER3) += ether3.o
obj-$(CONFIG_ARM_AT91_ETHER) += at91_ether.o
obj-$(CONFIG_ARM_KS8695_ETHER) += ks8695net.o
obj-$(CONFIG_EP93XX_ETH) += ep93xx_eth.o
diff --git a/drivers/net/ethernet/Kconfig b/drivers/net/ethernet/Kconfig
index 7d25fa4..35ed4c2 100644
--- a/drivers/net/ethernet/Kconfig
+++ b/drivers/net/ethernet/Kconfig
@@ -36,6 +36,7 @@ source "drivers/net/ethernet/pasemi/Kconfig"
source "drivers/net/ethernet/qlogic/Kconfig"
source "drivers/net/ethernet/racal/Kconfig"
source "drivers/net/ethernet/realtek/Kconfig"
+source "drivers/net/ethernet/seeq/Kconfig"
source "drivers/net/ethernet/sfc/Kconfig"
source "drivers/net/ethernet/sgi/Kconfig"
source "drivers/net/ethernet/smsc/Kconfig"
diff --git a/drivers/net/ethernet/Makefile b/drivers/net/ethernet/Makefile
index ec58715..ea0999f 100644
--- a/drivers/net/ethernet/Makefile
+++ b/drivers/net/ethernet/Makefile
@@ -27,6 +27,7 @@ obj-$(CONFIG_NET_VENDOR_PASEMI) += pasemi/
obj-$(CONFIG_NET_VENDOR_QLOGIC) += qlogic/
obj-$(CONFIG_NET_VENDOR_RACAL) += racal/
obj-$(CONFIG_NET_VENDOR_REALTEK) += realtek/
+obj-$(CONFIG_NET_VENDOR_SEEQ) += seeq/
obj-$(CONFIG_SFC) += sfc/
obj-$(CONFIG_NET_VENDOR_SGI) += sgi/
obj-$(CONFIG_NET_VENDOR_SMSC) += smsc/
diff --git a/drivers/net/ethernet/seeq/Kconfig b/drivers/net/ethernet/seeq/Kconfig
new file mode 100644
index 0000000..0266791
--- /dev/null
+++ b/drivers/net/ethernet/seeq/Kconfig
@@ -0,0 +1,45 @@
+#
+# SEEQ device configuration
+#
+
+config NET_VENDOR_SEEQ
+ bool "SEEQ devices"
+ depends on (ARM && ARCH_ACORN) || SGI_HAS_SEEQ || EXPERIMENTAL
+ ---help---
+ If you have a network (Ethernet) card belonging to this class, say Y
+ and read the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>.
+
+ Note that the answer to this question doesn't directly affect the
+ kernel: saying N will just cause the configurator to skip all
+ the questions about SEEQ devices. If you say Y, you will be asked for
+ your specific card in the following questions.
+
+if NET_VENDOR_SEEQ
+
+config ARM_ETHER3
+ tristate "Acorn/ANT Ether3 support"
+ depends on ARM && ARCH_ACORN
+ ---help---
+ If you have an Acorn system with one of these network cards, you
+ should say Y to this option if you wish to use it with Linux.
+
+config SEEQ8005
+ tristate "SEEQ8005 support (EXPERIMENTAL)"
+ depends on EXPERIMENTAL
+ ---help---
+ This is a driver for the SEEQ 8005 network (Ethernet) card. If this
+ is for you, read the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>.
+
+ To compile this driver as a module, choose M here. The module
+ will be called seeq8005.
+
+config SGISEEQ
+ tristate "SGI Seeq ethernet controller support"
+ depends on SGI_HAS_SEEQ
+ ---help---
+ Say Y here if you have an Seeq based Ethernet network card. This is
+ used in many Silicon Graphics machines.
+
+endif # NET_VENDOR_SEEQ
diff --git a/drivers/net/ethernet/seeq/Makefile b/drivers/net/ethernet/seeq/Makefile
new file mode 100644
index 0000000..3e258a5
--- /dev/null
+++ b/drivers/net/ethernet/seeq/Makefile
@@ -0,0 +1,7 @@
+#
+# Makefile for the SEEQ network device drivers
+#
+
+obj-$(CONFIG_ARM_ETHER3) += ether3.o
+obj-$(CONFIG_SEEQ8005) += seeq8005.o
+obj-$(CONFIG_SGISEEQ) += sgiseeq.o
diff --git a/drivers/net/arm/ether3.c b/drivers/net/ethernet/seeq/ether3.c
similarity index 100%
rename from drivers/net/arm/ether3.c
rename to drivers/net/ethernet/seeq/ether3.c
diff --git a/drivers/net/arm/ether3.h b/drivers/net/ethernet/seeq/ether3.h
similarity index 100%
rename from drivers/net/arm/ether3.h
rename to drivers/net/ethernet/seeq/ether3.h
diff --git a/drivers/net/seeq8005.c b/drivers/net/ethernet/seeq/seeq8005.c
similarity index 100%
rename from drivers/net/seeq8005.c
rename to drivers/net/ethernet/seeq/seeq8005.c
diff --git a/drivers/net/seeq8005.h b/drivers/net/ethernet/seeq/seeq8005.h
similarity index 100%
rename from drivers/net/seeq8005.h
rename to drivers/net/ethernet/seeq/seeq8005.h
diff --git a/drivers/net/sgiseeq.c b/drivers/net/ethernet/seeq/sgiseeq.c
similarity index 100%
rename from drivers/net/sgiseeq.c
rename to drivers/net/ethernet/seeq/sgiseeq.c
diff --git a/drivers/net/sgiseeq.h b/drivers/net/ethernet/seeq/sgiseeq.h
similarity index 100%
rename from drivers/net/sgiseeq.h
rename to drivers/net/ethernet/seeq/sgiseeq.h
--
1.7.6
^ permalink raw reply related [flat|nested] 21+ messages in thread* Re: [net-next 03/10] seeq: Move the SEEQ drivers
2011-08-12 7:32 ` [net-next 03/10] seeq: Move the SEEQ drivers Jeff Kirsher
@ 2011-08-18 19:36 ` Ralf Baechle
2011-11-04 17:24 ` Russell King - ARM Linux
1 sibling, 0 replies; 21+ messages in thread
From: Ralf Baechle @ 2011-08-18 19:36 UTC (permalink / raw)
To: Jeff Kirsher; +Cc: davem, netdev, gospo, sassmann, Russell King, Hamish Coleman
On Fri, Aug 12, 2011 at 12:32:57AM -0700, Jeff Kirsher wrote:
> Move the drivers that use SEEQ chipset into drivers/net/ethernet/seeq
> and make the necessary Kconfig and Makefile changes.
>
> CC: Russell King <linux@arm.linux.org.uk>
> CC: Hamish Coleman <hamish@zot.apana.org.au>
> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
> ---
> MAINTAINERS | 3 +-
> drivers/net/Kconfig | 18 -----------
> drivers/net/Makefile | 2 -
> drivers/net/arm/Kconfig | 7 ----
> drivers/net/arm/Makefile | 1 -
> drivers/net/ethernet/Kconfig | 1 +
> drivers/net/ethernet/Makefile | 1 +
> drivers/net/ethernet/seeq/Kconfig | 45 +++++++++++++++++++++++++++
> drivers/net/ethernet/seeq/Makefile | 7 ++++
> drivers/net/{arm => ethernet/seeq}/ether3.c | 0
> drivers/net/{arm => ethernet/seeq}/ether3.h | 0
> drivers/net/{ => ethernet/seeq}/seeq8005.c | 0
> drivers/net/{ => ethernet/seeq}/seeq8005.h | 0
> drivers/net/{ => ethernet/seeq}/sgiseeq.c | 0
> drivers/net/{ => ethernet/seeq}/sgiseeq.h | 0
> 15 files changed, 56 insertions(+), 29 deletions(-)
> create mode 100644 drivers/net/ethernet/seeq/Kconfig
> create mode 100644 drivers/net/ethernet/seeq/Makefile
> rename drivers/net/{arm => ethernet/seeq}/ether3.c (100%)
> rename drivers/net/{arm => ethernet/seeq}/ether3.h (100%)
> rename drivers/net/{ => ethernet/seeq}/seeq8005.c (100%)
> rename drivers/net/{ => ethernet/seeq}/seeq8005.h (100%)
> rename drivers/net/{ => ethernet/seeq}/sgiseeq.c (100%)
> rename drivers/net/{ => ethernet/seeq}/sgiseeq.h (100%)
This makes a lot more sense than shoving the Seeq drivers into
drivers/net/ethernet/sgi/ - even though sgiseeq depends on an SGI IP22/IP28
specific DMA engine.
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Ralf
^ permalink raw reply [flat|nested] 21+ messages in thread* Re: [net-next 03/10] seeq: Move the SEEQ drivers
2011-08-12 7:32 ` [net-next 03/10] seeq: Move the SEEQ drivers Jeff Kirsher
2011-08-18 19:36 ` Ralf Baechle
@ 2011-11-04 17:24 ` Russell King - ARM Linux
2011-11-04 21:10 ` Jeff Kirsher
2011-11-04 21:16 ` Joe Perches
1 sibling, 2 replies; 21+ messages in thread
From: Russell King - ARM Linux @ 2011-11-04 17:24 UTC (permalink / raw)
To: Jeff Kirsher, torvalds; +Cc: davem, netdev, gospo, sassmann, Hamish Coleman
Okay, this is the only patch I saw (for the SEEQ drivers), but I notice
that more of the ARM drivers have moved. The result is not nice. Or
even workable.
While looking for my ether1, ether3 and etherh drivers in Kconfig, I
enable every option which is presented to me under the new 'ethernet
drivers' stuff. I'm offered my ether3 driver under the SEEQ stuff -
that's fine. But what about the rest?
Well...
drivers/net/ethernet/intel/Kconfig:
config NET_VENDOR_INTEL
bool "Intel devices"
default y
depends on PCI || PCI_MSI
drivers/net/ethernet/i825xx/Kconfig:
config NET_VENDOR_I825XX
bool "Intel (82586/82593/82596) devices"
default y
depends on NET_VENDOR_INTEL && (ISA || ISA_DMA_API || ARM || \
ARCH_ACORN || MCA || MCA_LEGACY || SNI_RM || SUN3 || \
GSC || BVME6000 || MVME16x || EXPERIMENTAL)
if NET_VENDOR_I825XX
config ARM_ETHER1
tristate "Acorn Ether1 support"
depends on ARM && ARCH_ACORN
This is NOT a PCI driver, yet it has ended up with a requirement for
CONFIG_PCI to be set, which is nonsense for this platform because it
has no PCI.
What about etherh?
drivers/net/ethernet/natsemi/Kconfig:
config NET_VENDOR_NATSEMI
bool "National Semi-conductor devices"
default y
depends on MCA || MAC || MACH_JAZZ || PCI || XTENSA_PLATFORM_XT2000
drivers/net/ethernet/8390/Kconfig:
config NET_VENDOR_8390
bool "National Semi-conductor 8390 devices"
default y
depends on NET_VENDOR_NATSEMI && (AMIGA_PCMCIA || PCI || SUPERH || \
ISA || MCA || EISA || MAC || M32R || MACH_TX49XX || \
MCA_LEGACY || H8300 || ARM || MIPS || ZORRO || PCMCIA || \
EXPERIMENTAL)
if NET_VENDOR_8390
config ARM_ETHERH
tristate "I-cubed EtherH/ANT EtherM support"
depends on ARM && ARCH_ACORN
Again, exactly the same thing.
Thankfully, ARM_AM79C961A is right, so that's two out of five correct.
I've no idea what the right solution is to this complex maze of Kconfig
stuff. Do I through an 'ARM' into the NET_VENDOR_INTEL and
NET_VENDOR_NATSEMI dependencies?
While I realise this is a big change, and bugs like this are likely, it
would've been nice to be copied on more of the patches which affect
drivers I maintain.
^ permalink raw reply [flat|nested] 21+ messages in thread* Re: [net-next 03/10] seeq: Move the SEEQ drivers
2011-11-04 17:24 ` Russell King - ARM Linux
@ 2011-11-04 21:10 ` Jeff Kirsher
2011-11-04 21:35 ` Russell King - ARM Linux
2011-11-04 21:16 ` Joe Perches
1 sibling, 1 reply; 21+ messages in thread
From: Jeff Kirsher @ 2011-11-04 21:10 UTC (permalink / raw)
To: Russell King - ARM Linux
Cc: torvalds@linux-foundation.org, davem@davemloft.net,
netdev@vger.kernel.org, gospo@redhat.com, sassmann@redhat.com,
Hamish Coleman
[-- Attachment #1: Type: text/plain, Size: 2786 bytes --]
On Fri, 2011-11-04 at 10:24 -0700, Russell King - ARM Linux wrote:
> Okay, this is the only patch I saw (for the SEEQ drivers), but I notice
> that more of the ARM drivers have moved. The result is not nice. Or
> even workable.
>
> While looking for my ether1, ether3 and etherh drivers in Kconfig, I
> enable every option which is presented to me under the new 'ethernet
> drivers' stuff. I'm offered my ether3 driver under the SEEQ stuff -
> that's fine. But what about the rest?
>
> Well...
>
> drivers/net/ethernet/intel/Kconfig:
> config NET_VENDOR_INTEL
> bool "Intel devices"
> default y
> depends on PCI || PCI_MSI
>
> drivers/net/ethernet/i825xx/Kconfig:
> config NET_VENDOR_I825XX
> bool "Intel (82586/82593/82596) devices"
> default y
> depends on NET_VENDOR_INTEL && (ISA || ISA_DMA_API || ARM || \
> ARCH_ACORN || MCA || MCA_LEGACY || SNI_RM || SUN3 || \
> GSC || BVME6000 || MVME16x || EXPERIMENTAL)
>
> if NET_VENDOR_I825XX
> config ARM_ETHER1
> tristate "Acorn Ether1 support"
> depends on ARM && ARCH_ACORN
>
> This is NOT a PCI driver, yet it has ended up with a requirement for
> CONFIG_PCI to be set, which is nonsense for this platform because it
> has no PCI.
>
> What about etherh?
> drivers/net/ethernet/natsemi/Kconfig:
> config NET_VENDOR_NATSEMI
> bool "National Semi-conductor devices"
> default y
> depends on MCA || MAC || MACH_JAZZ || PCI || XTENSA_PLATFORM_XT2000
>
> drivers/net/ethernet/8390/Kconfig:
> config NET_VENDOR_8390
> bool "National Semi-conductor 8390 devices"
> default y
> depends on NET_VENDOR_NATSEMI && (AMIGA_PCMCIA || PCI || SUPERH || \
> ISA || MCA || EISA || MAC || M32R || MACH_TX49XX || \
> MCA_LEGACY || H8300 || ARM || MIPS || ZORRO || PCMCIA || \
> EXPERIMENTAL)
> if NET_VENDOR_8390
> config ARM_ETHERH
> tristate "I-cubed EtherH/ANT EtherM support"
> depends on ARM && ARCH_ACORN
>
> Again, exactly the same thing.
>
> Thankfully, ARM_AM79C961A is right, so that's two out of five correct.
>
> I've no idea what the right solution is to this complex maze of Kconfig
> stuff. Do I through an 'ARM' into the NET_VENDOR_INTEL and
> NET_VENDOR_NATSEMI dependencies?
>
> While I realise this is a big change, and bugs like this are likely, it
> would've been nice to be copied on more of the patches which affect
> drivers I maintain.
I just submitted a patch to resolve this issue with the "sub" Kconfig's
having a dependency which is not reflected in the "parent" Kconfig.
http://patchwork.ozlabs.org/patch/123250/
[-- Attachment #2: This is a digitally signed message part --]
[-- Type: application/pgp-signature, Size: 836 bytes --]
^ permalink raw reply [flat|nested] 21+ messages in thread
* Re: [net-next 03/10] seeq: Move the SEEQ drivers
2011-11-04 21:10 ` Jeff Kirsher
@ 2011-11-04 21:35 ` Russell King - ARM Linux
0 siblings, 0 replies; 21+ messages in thread
From: Russell King - ARM Linux @ 2011-11-04 21:35 UTC (permalink / raw)
To: Jeff Kirsher
Cc: torvalds@linux-foundation.org, davem@davemloft.net,
netdev@vger.kernel.org, gospo@redhat.com, sassmann@redhat.com,
Hamish Coleman
On Fri, Nov 04, 2011 at 02:10:02PM -0700, Jeff Kirsher wrote:
> I just submitted a patch to resolve this issue with the "sub" Kconfig's
> having a dependency which is not reflected in the "parent" Kconfig.
>
> http://patchwork.ozlabs.org/patch/123250/
Thanks, that seems to fix the issues for me. For that patch:
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
^ permalink raw reply [flat|nested] 21+ messages in thread
* Re: [net-next 03/10] seeq: Move the SEEQ drivers
2011-11-04 17:24 ` Russell King - ARM Linux
2011-11-04 21:10 ` Jeff Kirsher
@ 2011-11-04 21:16 ` Joe Perches
2011-11-04 21:25 ` Russell King - ARM Linux
1 sibling, 1 reply; 21+ messages in thread
From: Joe Perches @ 2011-11-04 21:16 UTC (permalink / raw)
To: Russell King - ARM Linux
Cc: Jeff Kirsher, torvalds, davem, netdev, gospo, sassmann,
Hamish Coleman
On Fri, 2011-11-04 at 17:24 +0000, Russell King - ARM Linux wrote:
> Okay, this is the only patch I saw (for the SEEQ drivers), but I notice
> that more of the ARM drivers have moved. The result is not nice. Or
> even workable.
>
> While looking for my ether1, ether3 and etherh drivers in Kconfig, I
> enable every option which is presented to me under the new 'ethernet
> drivers' stuff. I'm offered my ether3 driver under the SEEQ stuff -
> that's fine. But what about the rest?
[]
> While I realise this is a big change, and bugs like this are likely, it
> would've been nice to be copied on more of the patches which affect
> drivers I maintain.
Hi Russell.
What drivers in drivers/net do you maintain?
I believe this is the list in MAINTAINERS for you:
ARM/EBSA110 MACHINE SUPPORT
F: drivers/net/ethernet/amd/am79c961a.*
ARM/RISCPC ARCHITECTURE
F: drivers/net/ethernet/i825xx/ether1*
F: drivers/net/ethernet/seeq/ether3*
Are there others? If yes, what are they?
^ permalink raw reply [flat|nested] 21+ messages in thread
* Re: [net-next 03/10] seeq: Move the SEEQ drivers
2011-11-04 21:16 ` Joe Perches
@ 2011-11-04 21:25 ` Russell King - ARM Linux
2011-11-04 21:42 ` Jeff Kirsher
0 siblings, 1 reply; 21+ messages in thread
From: Russell King - ARM Linux @ 2011-11-04 21:25 UTC (permalink / raw)
To: Joe Perches
Cc: Jeff Kirsher, torvalds, davem, netdev, gospo, sassmann,
Hamish Coleman
On Fri, Nov 04, 2011 at 11:16:07PM +0200, Joe Perches wrote:
> On Fri, 2011-11-04 at 17:24 +0000, Russell King - ARM Linux wrote:
> > Okay, this is the only patch I saw (for the SEEQ drivers), but I notice
> > that more of the ARM drivers have moved. The result is not nice. Or
> > even workable.
> >
> > While looking for my ether1, ether3 and etherh drivers in Kconfig, I
> > enable every option which is presented to me under the new 'ethernet
> > drivers' stuff. I'm offered my ether3 driver under the SEEQ stuff -
> > that's fine. But what about the rest?
> []
> > While I realise this is a big change, and bugs like this are likely, it
> > would've been nice to be copied on more of the patches which affect
> > drivers I maintain.
>
> Hi Russell.
>
> What drivers in drivers/net do you maintain?
>
> I believe this is the list in MAINTAINERS for you:
>
> ARM/EBSA110 MACHINE SUPPORT
> F: drivers/net/ethernet/amd/am79c961a.*
> ARM/RISCPC ARCHITECTURE
> F: drivers/net/ethernet/i825xx/ether1*
> F: drivers/net/ethernet/seeq/ether3*
>
> Are there others? If yes, what are they?
If that's what's in mainline, then etherh has been dropped from that
list through this move. It's drivers/net/ethernet/8390/etherh*, so
that needs adding back for "ARM/RISCPC ARCHITECTURE".
It was correct - below seems to be what happened...
commit 115978859272b958366d4a08c99a24f9625fa663
Author: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Date: Wed Jul 13 15:38:08 2011 -0700
i825xx: Move the Intel 82586/82593/82596 based drivers
@@ -1014,7 +1014,7 @@ F: arch/arm/include/asm/hardware/ioc.h
F: arch/arm/include/asm/hardware/iomd.h
F: arch/arm/include/asm/hardware/memc.h
F: arch/arm/mach-rpc/
-F: drivers/net/arm/ether*
+F: drivers/net/arm/ether3*
That change was probably correct at the time, because this one which
came before it:
commit 644570b830266ff33ff5f3542b9c838f93a55ea6
Author: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Date: Sat Apr 2 06:20:12 2011 -0700
8390: Move the 8390 related drivers
which moved the etherh driver without updating MAINTAINERS for that
change.
^ permalink raw reply [flat|nested] 21+ messages in thread* Re: [net-next 03/10] seeq: Move the SEEQ drivers
2011-11-04 21:25 ` Russell King - ARM Linux
@ 2011-11-04 21:42 ` Jeff Kirsher
0 siblings, 0 replies; 21+ messages in thread
From: Jeff Kirsher @ 2011-11-04 21:42 UTC (permalink / raw)
To: Russell King - ARM Linux
Cc: Joe Perches, torvalds@linux-foundation.org, davem@davemloft.net,
netdev@vger.kernel.org, gospo@redhat.com, sassmann@redhat.com,
Hamish Coleman
[-- Attachment #1: Type: text/plain, Size: 2719 bytes --]
On Fri, 2011-11-04 at 14:25 -0700, Russell King - ARM Linux wrote:
> On Fri, Nov 04, 2011 at 11:16:07PM +0200, Joe Perches wrote:
> > On Fri, 2011-11-04 at 17:24 +0000, Russell King - ARM Linux wrote:
> > > Okay, this is the only patch I saw (for the SEEQ drivers), but I notice
> > > that more of the ARM drivers have moved. The result is not nice. Or
> > > even workable.
> > >
> > > While looking for my ether1, ether3 and etherh drivers in Kconfig, I
> > > enable every option which is presented to me under the new 'ethernet
> > > drivers' stuff. I'm offered my ether3 driver under the SEEQ stuff -
> > > that's fine. But what about the rest?
> > []
> > > While I realise this is a big change, and bugs like this are likely, it
> > > would've been nice to be copied on more of the patches which affect
> > > drivers I maintain.
> >
> > Hi Russell.
> >
> > What drivers in drivers/net do you maintain?
> >
> > I believe this is the list in MAINTAINERS for you:
> >
> > ARM/EBSA110 MACHINE SUPPORT
> > F: drivers/net/ethernet/amd/am79c961a.*
> > ARM/RISCPC ARCHITECTURE
> > F: drivers/net/ethernet/i825xx/ether1*
> > F: drivers/net/ethernet/seeq/ether3*
> >
> > Are there others? If yes, what are they?
>
> If that's what's in mainline, then etherh has been dropped from that
> list through this move. It's drivers/net/ethernet/8390/etherh*, so
> that needs adding back for "ARM/RISCPC ARCHITECTURE".
>
> It was correct - below seems to be what happened...
>
> commit 115978859272b958366d4a08c99a24f9625fa663
> Author: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
> Date: Wed Jul 13 15:38:08 2011 -0700
>
> i825xx: Move the Intel 82586/82593/82596 based drivers
>
> @@ -1014,7 +1014,7 @@ F: arch/arm/include/asm/hardware/ioc.h
> F: arch/arm/include/asm/hardware/iomd.h
> F: arch/arm/include/asm/hardware/memc.h
> F: arch/arm/mach-rpc/
> -F: drivers/net/arm/ether*
> +F: drivers/net/arm/ether3*
>
> That change was probably correct at the time, because this one which
> came before it:
>
> commit 644570b830266ff33ff5f3542b9c838f93a55ea6
> Author: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
> Date: Sat Apr 2 06:20:12 2011 -0700
>
> 8390: Move the 8390 related drivers
>
> which moved the etherh driver without updating MAINTAINERS for that
> change.
This was my bad. There was a lot of discussion and shuffling of drivers
early on to make sure we have the drivers in the right location, and I
initially had all the drivers/net/arm/ether* drivers in the same
location. I can put together a patch to resolve this if no one has one
in the works.
Sorry about that Russell.
[-- Attachment #2: This is a digitally signed message part --]
[-- Type: application/pgp-signature, Size: 836 bytes --]
^ permalink raw reply [flat|nested] 21+ messages in thread
* [net-next 04/10] pch_gbe: Move the OKI Semiconductor driver
2011-08-12 7:32 [net-next 00/10] drivers/net organize Ethernet drivers (4th series) Jeff Kirsher
` (2 preceding siblings ...)
2011-08-12 7:32 ` [net-next 03/10] seeq: Move the SEEQ drivers Jeff Kirsher
@ 2011-08-12 7:32 ` Jeff Kirsher
2011-08-12 7:32 ` [net-next 05/10] skge/sky2/mv643xx/pxa168: Move the Marvell Ethernet drivers Jeff Kirsher
` (6 subsequent siblings)
10 siblings, 0 replies; 21+ messages in thread
From: Jeff Kirsher @ 2011-08-12 7:32 UTC (permalink / raw)
To: davem; +Cc: Jeff Kirsher, netdev, gospo, sassmann, Tomoya, Toshiharu Okada
Move the OKI Semiconductor driver into driver/net/ethernet/oki-semi/
and make the necessary Kconfig and Makefile changes.
Note: there is no documented maintainer for this driver, so I CC'd
the last 2 major contributors.
CC: Tomoya <tomoya-linux@dsn.okisemi.com>
CC: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
drivers/net/Kconfig | 19 -----------------
drivers/net/Makefile | 1 -
drivers/net/ethernet/Kconfig | 1 +
drivers/net/ethernet/Makefile | 1 +
drivers/net/ethernet/oki-semi/Kconfig | 22 ++++++++++++++++++++
drivers/net/ethernet/oki-semi/Makefile | 5 ++++
drivers/net/ethernet/oki-semi/pch_gbe/Kconfig | 20 ++++++++++++++++++
.../net/{ => ethernet/oki-semi}/pch_gbe/Makefile | 0
.../net/{ => ethernet/oki-semi}/pch_gbe/pch_gbe.h | 0
.../{ => ethernet/oki-semi}/pch_gbe/pch_gbe_api.c | 0
.../{ => ethernet/oki-semi}/pch_gbe/pch_gbe_api.h | 0
.../oki-semi}/pch_gbe/pch_gbe_ethtool.c | 0
.../{ => ethernet/oki-semi}/pch_gbe/pch_gbe_main.c | 0
.../oki-semi}/pch_gbe/pch_gbe_param.c | 0
.../{ => ethernet/oki-semi}/pch_gbe/pch_gbe_phy.c | 0
.../{ => ethernet/oki-semi}/pch_gbe/pch_gbe_phy.h | 0
16 files changed, 49 insertions(+), 20 deletions(-)
create mode 100644 drivers/net/ethernet/oki-semi/Kconfig
create mode 100644 drivers/net/ethernet/oki-semi/Makefile
create mode 100644 drivers/net/ethernet/oki-semi/pch_gbe/Kconfig
rename drivers/net/{ => ethernet/oki-semi}/pch_gbe/Makefile (100%)
rename drivers/net/{ => ethernet/oki-semi}/pch_gbe/pch_gbe.h (100%)
rename drivers/net/{ => ethernet/oki-semi}/pch_gbe/pch_gbe_api.c (100%)
rename drivers/net/{ => ethernet/oki-semi}/pch_gbe/pch_gbe_api.h (100%)
rename drivers/net/{ => ethernet/oki-semi}/pch_gbe/pch_gbe_ethtool.c (100%)
rename drivers/net/{ => ethernet/oki-semi}/pch_gbe/pch_gbe_main.c (100%)
rename drivers/net/{ => ethernet/oki-semi}/pch_gbe/pch_gbe_param.c (100%)
rename drivers/net/{ => ethernet/oki-semi}/pch_gbe/pch_gbe_phy.c (100%)
rename drivers/net/{ => ethernet/oki-semi}/pch_gbe/pch_gbe_phy.h (100%)
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index 696464c..87e7a12 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -996,25 +996,6 @@ config S6GMAC
To compile this driver as a module, choose M here. The module
will be called s6gmac.
-config PCH_GBE
- tristate "Intel EG20T PCH / OKI SEMICONDUCTOR ML7223 IOH GbE"
- depends on PCI
- select MII
- ---help---
- This is a gigabit ethernet driver for EG20T PCH.
- EG20T PCH is the platform controller hub that is used in Intel's
- general embedded platform.
- EG20T PCH has Gigabit Ethernet interface.
- Using this interface, it is able to access system devices connected
- to Gigabit Ethernet.
- This driver enables Gigabit Ethernet function.
-
- This driver also can be used for OKI SEMICONDUCTOR IOH(Input/
- Output Hub), ML7223.
- ML7223 IOH is for MP(Media Phone) use.
- ML7223 is companion chip for Intel Atom E6xx series.
- ML7223 is completely compatible for Intel EG20T PCH.
-
endif # NETDEV_1000
#
diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index b1ead87..141ed25 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -156,5 +156,4 @@ obj-$(CONFIG_WIMAX) += wimax/
obj-$(CONFIG_CAIF) += caif/
obj-$(CONFIG_OCTEON_MGMT_ETHERNET) += octeon/
-obj-$(CONFIG_PCH_GBE) += pch_gbe/
obj-$(CONFIG_TILE_NET) += tile/
diff --git a/drivers/net/ethernet/Kconfig b/drivers/net/ethernet/Kconfig
index 35ed4c2..0eaf957 100644
--- a/drivers/net/ethernet/Kconfig
+++ b/drivers/net/ethernet/Kconfig
@@ -32,6 +32,7 @@ source "drivers/net/ethernet/mellanox/Kconfig"
source "drivers/net/ethernet/myricom/Kconfig"
source "drivers/net/ethernet/natsemi/Kconfig"
source "drivers/net/ethernet/8390/Kconfig"
+source "drivers/net/ethernet/oki-semi/Kconfig"
source "drivers/net/ethernet/pasemi/Kconfig"
source "drivers/net/ethernet/qlogic/Kconfig"
source "drivers/net/ethernet/racal/Kconfig"
diff --git a/drivers/net/ethernet/Makefile b/drivers/net/ethernet/Makefile
index ea0999f..b5ca872 100644
--- a/drivers/net/ethernet/Makefile
+++ b/drivers/net/ethernet/Makefile
@@ -23,6 +23,7 @@ obj-$(CONFIG_NET_VENDOR_XSCALE) += xscale/
obj-$(CONFIG_NET_VENDOR_MELLANOX) += mellanox/
obj-$(CONFIG_NET_VENDOR_MYRI) += myricom/
obj-$(CONFIG_NET_VENDOR_NATSEMI) += natsemi/
+obj-$(CONFIG_NET_VENDOR_OKI) += oki-semi/
obj-$(CONFIG_NET_VENDOR_PASEMI) += pasemi/
obj-$(CONFIG_NET_VENDOR_QLOGIC) += qlogic/
obj-$(CONFIG_NET_VENDOR_RACAL) += racal/
diff --git a/drivers/net/ethernet/oki-semi/Kconfig b/drivers/net/ethernet/oki-semi/Kconfig
new file mode 100644
index 0000000..97f5e72
--- /dev/null
+++ b/drivers/net/ethernet/oki-semi/Kconfig
@@ -0,0 +1,22 @@
+#
+# OKI Semiconductor device configuration
+#
+
+config NET_VENDOR_OKI
+ bool "OKI Semiconductor devices"
+ depends on PCI
+ ---help---
+ If you have a network (Ethernet) card belonging to this class, say Y
+ and read the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>.
+
+ Note that the answer to this question doesn't directly affect the
+ kernel: saying N will just cause the configurator to skip all
+ the questions about OKI Semiconductor cards. If you say Y, you will
+ be asked for your specific card in the following questions.
+
+if NET_VENDOR_OKI
+
+source "drivers/net/ethernet/oki-semi/pch_gbe/Kconfig"
+
+endif # NET_VENDOR_OKI
diff --git a/drivers/net/ethernet/oki-semi/Makefile b/drivers/net/ethernet/oki-semi/Makefile
new file mode 100644
index 0000000..b6780c8
--- /dev/null
+++ b/drivers/net/ethernet/oki-semi/Makefile
@@ -0,0 +1,5 @@
+#
+# Makefile for the OKI Semiconductor device drivers.
+#
+
+obj-$(CONFIG_PCH_GBE) += pch_gbe/
diff --git a/drivers/net/ethernet/oki-semi/pch_gbe/Kconfig b/drivers/net/ethernet/oki-semi/pch_gbe/Kconfig
new file mode 100644
index 0000000..c85709d
--- /dev/null
+++ b/drivers/net/ethernet/oki-semi/pch_gbe/Kconfig
@@ -0,0 +1,20 @@
+#
+# OKI Semiconductor device configuration
+#
+
+config PCH_GBE
+ tristate "OKI SEMICONDUCTOR ML7223 IOH GbE (Intel EG20T PCH)"
+ depends on PCI
+ select MII
+ ---help---
+ This is a gigabit ethernet driver for EG20T PCH.
+ EG20T PCH is the platform controller hub that is used in Intel's
+ general embedded platform. EG20T PCH has Gigabit Ethernet interface.
+ Using this interface, it is able to access system devices connected
+ to Gigabit Ethernet. This driver enables Gigabit Ethernet function.
+
+ This driver also can be used for OKI SEMICONDUCTOR IOH(Input/
+ Output Hub), ML7223.
+ ML7223 IOH is for MP(Media Phone) use.
+ ML7223 is companion chip for Intel Atom E6xx series.
+ ML7223 is completely compatible for Intel EG20T PCH.
diff --git a/drivers/net/pch_gbe/Makefile b/drivers/net/ethernet/oki-semi/pch_gbe/Makefile
similarity index 100%
rename from drivers/net/pch_gbe/Makefile
rename to drivers/net/ethernet/oki-semi/pch_gbe/Makefile
diff --git a/drivers/net/pch_gbe/pch_gbe.h b/drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe.h
similarity index 100%
rename from drivers/net/pch_gbe/pch_gbe.h
rename to drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe.h
diff --git a/drivers/net/pch_gbe/pch_gbe_api.c b/drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_api.c
similarity index 100%
rename from drivers/net/pch_gbe/pch_gbe_api.c
rename to drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_api.c
diff --git a/drivers/net/pch_gbe/pch_gbe_api.h b/drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_api.h
similarity index 100%
rename from drivers/net/pch_gbe/pch_gbe_api.h
rename to drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_api.h
diff --git a/drivers/net/pch_gbe/pch_gbe_ethtool.c b/drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_ethtool.c
similarity index 100%
rename from drivers/net/pch_gbe/pch_gbe_ethtool.c
rename to drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_ethtool.c
diff --git a/drivers/net/pch_gbe/pch_gbe_main.c b/drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_main.c
similarity index 100%
rename from drivers/net/pch_gbe/pch_gbe_main.c
rename to drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_main.c
diff --git a/drivers/net/pch_gbe/pch_gbe_param.c b/drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_param.c
similarity index 100%
rename from drivers/net/pch_gbe/pch_gbe_param.c
rename to drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_param.c
diff --git a/drivers/net/pch_gbe/pch_gbe_phy.c b/drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_phy.c
similarity index 100%
rename from drivers/net/pch_gbe/pch_gbe_phy.c
rename to drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_phy.c
diff --git a/drivers/net/pch_gbe/pch_gbe_phy.h b/drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_phy.h
similarity index 100%
rename from drivers/net/pch_gbe/pch_gbe_phy.h
rename to drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_phy.h
--
1.7.6
^ permalink raw reply related [flat|nested] 21+ messages in thread* [net-next 05/10] skge/sky2/mv643xx/pxa168: Move the Marvell Ethernet drivers
2011-08-12 7:32 [net-next 00/10] drivers/net organize Ethernet drivers (4th series) Jeff Kirsher
` (3 preceding siblings ...)
2011-08-12 7:32 ` [net-next 04/10] pch_gbe: Move the OKI Semiconductor driver Jeff Kirsher
@ 2011-08-12 7:32 ` Jeff Kirsher
2011-08-12 7:33 ` [net-next 06/10] via-*: Move the VIA drivers Jeff Kirsher
` (5 subsequent siblings)
10 siblings, 0 replies; 21+ messages in thread
From: Jeff Kirsher @ 2011-08-12 7:32 UTC (permalink / raw)
To: davem
Cc: Jeff Kirsher, netdev, gospo, sassmann, Sachin Sanap, Zhangfei Gao,
Philip Rakity, Mark Brown, Lennert Buytenhek, Stephen Hemminger
Move the Marvell Ethernet drivers into drivers/net/ethernet/marvell/
and make the necessary Kconfig and Makefile changes.
CC: Sachin Sanap <ssanap@marvell.com>
CC: Zhangfei Gao <zgao6@marvell.com>
CC: Philip Rakity <prakity@marvell.com>
CC: Mark Brown <markb@marvell.com>
CC: Lennert Buytenhek <buytenh@marvell.com>
CC: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
MAINTAINERS | 5 +-
drivers/net/Kconfig | 90 ------------------
drivers/net/Makefile | 4 -
drivers/net/ethernet/Kconfig | 1 +
drivers/net/ethernet/Makefile | 1 +
drivers/net/ethernet/marvell/Kconfig | 110 ++++++++++++++++++++++
drivers/net/ethernet/marvell/Makefile | 8 ++
drivers/net/{ => ethernet/marvell}/mv643xx_eth.c | 0
drivers/net/{ => ethernet/marvell}/pxa168_eth.c | 0
drivers/net/{ => ethernet/marvell}/skge.c | 0
drivers/net/{ => ethernet/marvell}/skge.h | 0
drivers/net/{ => ethernet/marvell}/sky2.c | 0
drivers/net/{ => ethernet/marvell}/sky2.h | 0
13 files changed, 122 insertions(+), 97 deletions(-)
create mode 100644 drivers/net/ethernet/marvell/Kconfig
create mode 100644 drivers/net/ethernet/marvell/Makefile
rename drivers/net/{ => ethernet/marvell}/mv643xx_eth.c (100%)
rename drivers/net/{ => ethernet/marvell}/pxa168_eth.c (100%)
rename drivers/net/{ => ethernet/marvell}/skge.c (100%)
rename drivers/net/{ => ethernet/marvell}/skge.h (100%)
rename drivers/net/{ => ethernet/marvell}/sky2.c (100%)
rename drivers/net/{ => ethernet/marvell}/sky2.h (100%)
diff --git a/MAINTAINERS b/MAINTAINERS
index e986e3e..b9acfde 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -4122,7 +4122,7 @@ MARVELL MV643XX ETHERNET DRIVER
M: Lennert Buytenhek <buytenh@wantstofly.org>
L: netdev@vger.kernel.org
S: Maintained
-F: drivers/net/mv643xx_eth.*
+F: drivers/net/ethernet/marvell/mv643xx_eth.*
F: include/linux/mv643xx.h
MARVELL MWIFIEX WIRELESS DRIVER
@@ -5854,8 +5854,7 @@ SKGE, SKY2 10/100/1000 GIGABIT ETHERNET DRIVERS
M: Stephen Hemminger <shemminger@linux-foundation.org>
L: netdev@vger.kernel.org
S: Maintained
-F: drivers/net/skge.*
-F: drivers/net/sky2.*
+F: drivers/net/ethernet/marvell/sk*
SLAB ALLOCATOR
M: Christoph Lameter <cl@linux-foundation.org>
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index 87e7a12..cb6c694 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -313,16 +313,6 @@ config BFIN_MAC_USE_HWSTAMP
help
To support the IEEE 1588 Precision Time Protocol (PTP), select y here
-config PXA168_ETH
- tristate "Marvell pxa168 ethernet support"
- depends on CPU_PXA168
- select PHYLIB
- help
- This driver supports the pxa168 Ethernet ports.
-
- To compile this driver as a module, choose M here. The module
- will be called pxa168_eth.
-
config NET_NETX
tristate "NetX Ethernet support"
select MII
@@ -803,73 +793,6 @@ config SIS190
To compile this driver as a module, choose M here: the module
will be called sis190. This is recommended.
-config SKGE
- tristate "Marvell Yukon Gigabit Ethernet support"
- depends on PCI
- select CRC32
- ---help---
- This driver support the Marvell Yukon or SysKonnect SK-98xx/SK-95xx
- and related Gigabit Ethernet adapters. It is a new smaller driver
- with better performance and more complete ethtool support.
-
- It does not support the link failover and network management
- features that "portable" vendor supplied sk98lin driver does.
-
- This driver supports adapters based on the original Yukon chipset:
- Marvell 88E8001, Belkin F5D5005, CNet GigaCard, DLink DGE-530T,
- Linksys EG1032/EG1064, 3Com 3C940/3C940B, SysKonnect SK-9871/9872.
-
- It does not support the newer Yukon2 chipset: a separate driver,
- sky2, is provided for these adapters.
-
- To compile this driver as a module, choose M here: the module
- will be called skge. This is recommended.
-
-config SKGE_DEBUG
- bool "Debugging interface"
- depends on SKGE && DEBUG_FS
- help
- This option adds the ability to dump driver state for debugging.
- The file /sys/kernel/debug/skge/ethX displays the state of the internal
- transmit and receive rings.
-
- If unsure, say N.
-
-config SKGE_GENESIS
- bool "Support for older SysKonnect Genesis boards"
- depends on SKGE
- help
- This enables support for the older and uncommon SysKonnect Genesis
- chips, which support MII via an external transceiver, instead of
- an internal one. Disabling this option will save some memory
- by making code smaller. If unsure say Y.
-
-config SKY2
- tristate "Marvell Yukon 2 support"
- depends on PCI
- select CRC32
- ---help---
- This driver supports Gigabit Ethernet adapters based on the
- Marvell Yukon 2 chipset:
- Marvell 88E8021/88E8022/88E8035/88E8036/88E8038/88E8050/88E8052/
- 88E8053/88E8055/88E8061/88E8062, SysKonnect SK-9E21D/SK-9S21
-
- There is companion driver for the older Marvell Yukon and
- SysKonnect Genesis based adapters: skge.
-
- To compile this driver as a module, choose M here: the module
- will be called sky2. This is recommended.
-
-config SKY2_DEBUG
- bool "Debugging interface"
- depends on SKY2 && DEBUG_FS
- help
- This option adds the ability to dump driver state for debugging.
- The file /sys/kernel/debug/sky2/ethX displays the state of the internal
- transmit and receive rings.
-
- If unsure, say N.
-
config VIA_VELOCITY
tristate "VIA Velocity support"
depends on PCI
@@ -952,19 +875,6 @@ config UGETH_TX_ON_DEMAND
bool "Transmit on Demand support"
depends on UCC_GETH
-config MV643XX_ETH
- tristate "Marvell Discovery (643XX) and Orion ethernet support"
- depends on (MV64X60 || PPC32 || PLAT_ORION) && INET
- select INET_LRO
- select PHYLIB
- help
- This driver supports the gigabit ethernet MACs in the
- Marvell Discovery PPC/MIPS chipset family (MV643XX) and
- in the Marvell Orion ARM SoC family.
-
- Some boards that use the Discovery chipset are the Momenco
- Ocelot C and Jaguar ATX and Pegasos II.
-
config XILINX_LL_TEMAC
tristate "Xilinx LL TEMAC (LocalLink Tri-mode Ethernet MAC) driver"
depends on PPC || MICROBLAZE
diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index 141ed25..69ca6a0 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -46,8 +46,6 @@ obj-$(CONFIG_GELIC_NET) += ps3_gelic.o
gelic_wireless-$(CONFIG_GELIC_WIRELESS) += ps3_gelic_wireless.o
ps3_gelic-objs += ps3_gelic_net.o $(gelic_wireless-y)
obj-$(CONFIG_TC35815) += tc35815.o
-obj-$(CONFIG_SKGE) += skge.o
-obj-$(CONFIG_SKY2) += sky2.o
obj-$(CONFIG_SKFP) += skfp/
obj-$(CONFIG_KS8842) += ks8842.o
obj-$(CONFIG_KS8851) += ks8851.o
@@ -75,7 +73,6 @@ endif
obj-$(CONFIG_FORCEDETH) += forcedeth.o
obj-$(CONFIG_TSI108_ETH) += tsi108_eth.o
-obj-$(CONFIG_MV643XX_ETH) += mv643xx_eth.o
ll_temac-objs := ll_temac_main.o ll_temac_mdio.o
obj-$(CONFIG_XILINX_LL_TEMAC) += ll_temac.o
obj-$(CONFIG_XILINX_EMACLITE) += xilinx_emaclite.o
@@ -111,7 +108,6 @@ obj-$(CONFIG_MIPS_SIM_NET) += mipsnet.o
obj-$(CONFIG_TUN) += tun.o
obj-$(CONFIG_VETH) += veth.o
obj-$(CONFIG_NET_NETX) += netx-eth.o
-obj-$(CONFIG_PXA168_ETH) += pxa168_eth.o
obj-$(CONFIG_BFIN_MAC) += bfin_mac.o
obj-$(CONFIG_DM9000) += dm9000.o
obj-$(CONFIG_ENC28J60) += enc28j60.o
diff --git a/drivers/net/ethernet/Kconfig b/drivers/net/ethernet/Kconfig
index 0eaf957..1c447d9 100644
--- a/drivers/net/ethernet/Kconfig
+++ b/drivers/net/ethernet/Kconfig
@@ -28,6 +28,7 @@ source "drivers/net/ethernet/ibm/Kconfig"
source "drivers/net/ethernet/intel/Kconfig"
source "drivers/net/ethernet/i825xx/Kconfig"
source "drivers/net/ethernet/xscale/Kconfig"
+source "drivers/net/ethernet/marvell/Kconfig"
source "drivers/net/ethernet/mellanox/Kconfig"
source "drivers/net/ethernet/myricom/Kconfig"
source "drivers/net/ethernet/natsemi/Kconfig"
diff --git a/drivers/net/ethernet/Makefile b/drivers/net/ethernet/Makefile
index b5ca872..48c8656 100644
--- a/drivers/net/ethernet/Makefile
+++ b/drivers/net/ethernet/Makefile
@@ -20,6 +20,7 @@ obj-$(CONFIG_NET_VENDOR_IBM) += ibm/
obj-$(CONFIG_NET_VENDOR_INTEL) += intel/
obj-$(CONFIG_NET_VENDOR_I825XX) += i825xx/
obj-$(CONFIG_NET_VENDOR_XSCALE) += xscale/
+obj-$(CONFIG_NET_VENDOR_MARVELL) += marvell/
obj-$(CONFIG_NET_VENDOR_MELLANOX) += mellanox/
obj-$(CONFIG_NET_VENDOR_MYRI) += myricom/
obj-$(CONFIG_NET_VENDOR_NATSEMI) += natsemi/
diff --git a/drivers/net/ethernet/marvell/Kconfig b/drivers/net/ethernet/marvell/Kconfig
new file mode 100644
index 0000000..e525408
--- /dev/null
+++ b/drivers/net/ethernet/marvell/Kconfig
@@ -0,0 +1,110 @@
+#
+# Marvell device configuration
+#
+
+config NET_VENDOR_MARVELL
+ bool "Marvell devices"
+ depends on PCI || CPU_PXA168 || MV64X60 || PPC32 || PLAT_ORION || INET
+ ---help---
+ If you have a network (Ethernet) card belonging to this class, say Y
+ and read the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>.
+
+ Note that the answer to this question doesn't directly affect the
+ kernel: saying N will just cause the configurator to skip all
+ the questions about Marvell devices. If you say Y, you will be
+ asked for your specific card in the following questions.
+
+if NET_VENDOR_MARVELL
+
+config MV643XX_ETH
+ tristate "Marvell Discovery (643XX) and Orion ethernet support"
+ depends on (MV64X60 || PPC32 || PLAT_ORION) && INET
+ select INET_LRO
+ select PHYLIB
+ ---help---
+ This driver supports the gigabit ethernet MACs in the
+ Marvell Discovery PPC/MIPS chipset family (MV643XX) and
+ in the Marvell Orion ARM SoC family.
+
+ Some boards that use the Discovery chipset are the Momenco
+ Ocelot C and Jaguar ATX and Pegasos II.
+
+config PXA168_ETH
+ tristate "Marvell pxa168 ethernet support"
+ depends on CPU_PXA168
+ select PHYLIB
+ ---help---
+ This driver supports the pxa168 Ethernet ports.
+
+ To compile this driver as a module, choose M here. The module
+ will be called pxa168_eth.
+
+config SKGE
+ tristate "Marvell Yukon Gigabit Ethernet support"
+ depends on PCI
+ select CRC32
+ ---help---
+ This driver support the Marvell Yukon or SysKonnect SK-98xx/SK-95xx
+ and related Gigabit Ethernet adapters. It is a new smaller driver
+ with better performance and more complete ethtool support.
+
+ It does not support the link failover and network management
+ features that "portable" vendor supplied sk98lin driver does.
+
+ This driver supports adapters based on the original Yukon chipset:
+ Marvell 88E8001, Belkin F5D5005, CNet GigaCard, DLink DGE-530T,
+ Linksys EG1032/EG1064, 3Com 3C940/3C940B, SysKonnect SK-9871/9872.
+
+ It does not support the newer Yukon2 chipset: a separate driver,
+ sky2, is provided for these adapters.
+
+ To compile this driver as a module, choose M here: the module
+ will be called skge. This is recommended.
+
+config SKGE_DEBUG
+ bool "Debugging interface"
+ depends on SKGE && DEBUG_FS
+ ---help---
+ This option adds the ability to dump driver state for debugging.
+ The file /sys/kernel/debug/skge/ethX displays the state of the internal
+ transmit and receive rings.
+
+ If unsure, say N.
+
+config SKGE_GENESIS
+ bool "Support for older SysKonnect Genesis boards"
+ depends on SKGE
+ ---help---
+ This enables support for the older and uncommon SysKonnect Genesis
+ chips, which support MII via an external transceiver, instead of
+ an internal one. Disabling this option will save some memory
+ by making code smaller. If unsure say Y.
+
+config SKY2
+ tristate "Marvell Yukon 2 support"
+ depends on PCI
+ select CRC32
+ ---help---
+ This driver supports Gigabit Ethernet adapters based on the
+ Marvell Yukon 2 chipset:
+ Marvell 88E8021/88E8022/88E8035/88E8036/88E8038/88E8050/88E8052/
+ 88E8053/88E8055/88E8061/88E8062, SysKonnect SK-9E21D/SK-9S21
+
+ There is companion driver for the older Marvell Yukon and
+ SysKonnect Genesis based adapters: skge.
+
+ To compile this driver as a module, choose M here: the module
+ will be called sky2. This is recommended.
+
+config SKY2_DEBUG
+ bool "Debugging interface"
+ depends on SKY2 && DEBUG_FS
+ ---help---
+ This option adds the ability to dump driver state for debugging.
+ The file /sys/kernel/debug/sky2/ethX displays the state of the internal
+ transmit and receive rings.
+
+ If unsure, say N.
+
+endif # NET_VENDOR_MARVELL
diff --git a/drivers/net/ethernet/marvell/Makefile b/drivers/net/ethernet/marvell/Makefile
new file mode 100644
index 0000000..57e3234
--- /dev/null
+++ b/drivers/net/ethernet/marvell/Makefile
@@ -0,0 +1,8 @@
+#
+# Makefile for the Marvell device drivers.
+#
+
+obj-$(CONFIG_MV643XX_ETH) += mv643xx_eth.o
+obj-$(CONFIG_PXA168_ETH) += pxa168_eth.o
+obj-$(CONFIG_SKGE) += skge.o
+obj-$(CONFIG_SKY2) += sky2.o
diff --git a/drivers/net/mv643xx_eth.c b/drivers/net/ethernet/marvell/mv643xx_eth.c
similarity index 100%
rename from drivers/net/mv643xx_eth.c
rename to drivers/net/ethernet/marvell/mv643xx_eth.c
diff --git a/drivers/net/pxa168_eth.c b/drivers/net/ethernet/marvell/pxa168_eth.c
similarity index 100%
rename from drivers/net/pxa168_eth.c
rename to drivers/net/ethernet/marvell/pxa168_eth.c
diff --git a/drivers/net/skge.c b/drivers/net/ethernet/marvell/skge.c
similarity index 100%
rename from drivers/net/skge.c
rename to drivers/net/ethernet/marvell/skge.c
diff --git a/drivers/net/skge.h b/drivers/net/ethernet/marvell/skge.h
similarity index 100%
rename from drivers/net/skge.h
rename to drivers/net/ethernet/marvell/skge.h
diff --git a/drivers/net/sky2.c b/drivers/net/ethernet/marvell/sky2.c
similarity index 100%
rename from drivers/net/sky2.c
rename to drivers/net/ethernet/marvell/sky2.c
diff --git a/drivers/net/sky2.h b/drivers/net/ethernet/marvell/sky2.h
similarity index 100%
rename from drivers/net/sky2.h
rename to drivers/net/ethernet/marvell/sky2.h
--
1.7.6
^ permalink raw reply related [flat|nested] 21+ messages in thread* [net-next 06/10] via-*: Move the VIA drivers
2011-08-12 7:32 [net-next 00/10] drivers/net organize Ethernet drivers (4th series) Jeff Kirsher
` (4 preceding siblings ...)
2011-08-12 7:32 ` [net-next 05/10] skge/sky2/mv643xx/pxa168: Move the Marvell Ethernet drivers Jeff Kirsher
@ 2011-08-12 7:33 ` Jeff Kirsher
2011-08-12 7:33 ` [net-next 07/10] eth16i: Move the Allied Telesis/Fujitsu drivers Jeff Kirsher
` (4 subsequent siblings)
10 siblings, 0 replies; 21+ messages in thread
From: Jeff Kirsher @ 2011-08-12 7:33 UTC (permalink / raw)
To: davem; +Cc: Jeff Kirsher, netdev, gospo, sassmann, Roger Luethi,
Francois Romieu
Move the VIA drivers into drivers/net/ethernet/via/ and make the
necessary Kconfig and Makefile changes.
CC: Roger Luethi <rl@hellgate.ch>
CC: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
MAINTAINERS | 4 +-
drivers/net/Kconfig | 36 ----------------
drivers/net/Makefile | 2 -
drivers/net/ethernet/Kconfig | 1 +
drivers/net/ethernet/Makefile | 1 +
drivers/net/ethernet/via/Kconfig | 56 +++++++++++++++++++++++++
drivers/net/ethernet/via/Makefile | 6 +++
drivers/net/{ => ethernet/via}/via-rhine.c | 0
drivers/net/{ => ethernet/via}/via-velocity.c | 0
drivers/net/{ => ethernet/via}/via-velocity.h | 0
10 files changed, 66 insertions(+), 40 deletions(-)
create mode 100644 drivers/net/ethernet/via/Kconfig
create mode 100644 drivers/net/ethernet/via/Makefile
rename drivers/net/{ => ethernet/via}/via-rhine.c (100%)
rename drivers/net/{ => ethernet/via}/via-velocity.c (100%)
rename drivers/net/{ => ethernet/via}/via-velocity.h (100%)
diff --git a/MAINTAINERS b/MAINTAINERS
index b9acfde..51d9281 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -6988,7 +6988,7 @@ F: include/linux/vhost.h
VIA RHINE NETWORK DRIVER
M: Roger Luethi <rl@hellgate.ch>
S: Maintained
-F: drivers/net/via-rhine.c
+F: drivers/net/ethernet/via/via-rhine.c
VIAPRO SMBUS DRIVER
M: Jean Delvare <khali@linux-fr.org>
@@ -7016,7 +7016,7 @@ VIA VELOCITY NETWORK DRIVER
M: Francois Romieu <romieu@fr.zoreil.com>
L: netdev@vger.kernel.org
S: Maintained
-F: drivers/net/via-velocity.*
+F: drivers/net/ethernet/via/via-velocity.*
VLAN (802.1Q)
M: Patrick McHardy <kaber@trash.net>
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index cb6c694..c1e491a 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -614,30 +614,6 @@ config KS8851_MLL
This platform driver is for Micrel KS8851 Address/data bus
multiplexed network chip.
-config VIA_RHINE
- tristate "VIA Rhine support"
- depends on NET_PCI && PCI
- select CRC32
- select MII
- help
- If you have a VIA "Rhine" based network card (Rhine-I (VT86C100A),
- Rhine-II (VT6102), or Rhine-III (VT6105)), say Y here. Rhine-type
- Ethernet functions can also be found integrated on South Bridges
- (e.g. VT8235).
-
- To compile this driver as a module, choose M here. The module
- will be called via-rhine.
-
-config VIA_RHINE_MMIO
- bool "Use MMIO instead of PIO"
- depends on VIA_RHINE
- help
- This instructs the driver to use PCI shared memory (MMIO) instead of
- programmed I/O ports (PIO). Enabling this gives an improvement in
- processing time in parts of the driver.
-
- If unsure, say Y.
-
config CPMAC
tristate "TI AR7 CPMAC Ethernet support (EXPERIMENTAL)"
depends on NET_ETHERNET && EXPERIMENTAL && AR7
@@ -793,18 +769,6 @@ config SIS190
To compile this driver as a module, choose M here: the module
will be called sis190. This is recommended.
-config VIA_VELOCITY
- tristate "VIA Velocity support"
- depends on PCI
- select CRC32
- select CRC_CCITT
- select MII
- help
- If you have a VIA "Velocity" based network card say Y here.
-
- To compile this driver as a module, choose M here. The module
- will be called via-velocity.
-
config SPIDER_NET
tristate "Spider Gigabit Ethernet driver"
depends on PCI && (PPC_IBM_CELL_BLADE || PPC_CELLEB)
diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index 69ca6a0..7e1128f 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -51,8 +51,6 @@ obj-$(CONFIG_KS8842) += ks8842.o
obj-$(CONFIG_KS8851) += ks8851.o
obj-$(CONFIG_KS8851_MLL) += ks8851_mll.o
obj-$(CONFIG_KSZ884X_PCI) += ksz884x.o
-obj-$(CONFIG_VIA_RHINE) += via-rhine.o
-obj-$(CONFIG_VIA_VELOCITY) += via-velocity.o
obj-$(CONFIG_ADAPTEC_STARFIRE) += starfire.o
obj-$(CONFIG_RIONET) += rionet.o
obj-$(CONFIG_SH_ETH) += sh_eth.o
diff --git a/drivers/net/ethernet/Kconfig b/drivers/net/ethernet/Kconfig
index 1c447d9..bdc0df8 100644
--- a/drivers/net/ethernet/Kconfig
+++ b/drivers/net/ethernet/Kconfig
@@ -45,5 +45,6 @@ source "drivers/net/ethernet/smsc/Kconfig"
source "drivers/net/ethernet/stmicro/Kconfig"
source "drivers/net/ethernet/sun/Kconfig"
source "drivers/net/ethernet/tehuti/Kconfig"
+source "drivers/net/ethernet/via/Kconfig"
endif # ETHERNET
diff --git a/drivers/net/ethernet/Makefile b/drivers/net/ethernet/Makefile
index 48c8656..ac60ac9 100644
--- a/drivers/net/ethernet/Makefile
+++ b/drivers/net/ethernet/Makefile
@@ -36,3 +36,4 @@ obj-$(CONFIG_NET_VENDOR_SMSC) += smsc/
obj-$(CONFIG_NET_VENDOR_STMICRO) += stmicro/
obj-$(CONFIG_NET_VENDOR_SUN) += sun/
obj-$(CONFIG_NET_VENDOR_TEHUTI) += tehuti/
+obj-$(CONFIG_NET_VENDOR_VIA) += via/
diff --git a/drivers/net/ethernet/via/Kconfig b/drivers/net/ethernet/via/Kconfig
new file mode 100644
index 0000000..7199194
--- /dev/null
+++ b/drivers/net/ethernet/via/Kconfig
@@ -0,0 +1,56 @@
+#
+# VIA device configuration
+#
+
+config NET_VENDOR_VIA
+ bool "VIA devices"
+ depends on PCI
+ ---help---
+ If you have a network (Ethernet) card belonging to this class, say Y
+ and read the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>.
+
+ Note that the answer to this question doesn't directly affect the
+ kernel: saying N will just cause the configurator to skip all
+ the questions about VIA devices. If you say Y, you will be asked for
+ your specific card in the following questions.
+
+if NET_VENDOR_VIA
+
+config VIA_RHINE
+ tristate "VIA Rhine support"
+ depends on PCI
+ select CRC32
+ select MII
+ ---help---
+ If you have a VIA "Rhine" based network card (Rhine-I (VT86C100A),
+ Rhine-II (VT6102), or Rhine-III (VT6105)), say Y here. Rhine-type
+ Ethernet functions can also be found integrated on South Bridges
+ (e.g. VT8235).
+
+ To compile this driver as a module, choose M here. The module
+ will be called via-rhine.
+
+config VIA_RHINE_MMIO
+ bool "Use MMIO instead of PIO"
+ depends on VIA_RHINE
+ ---help---
+ This instructs the driver to use PCI shared memory (MMIO) instead of
+ programmed I/O ports (PIO). Enabling this gives an improvement in
+ processing time in parts of the driver.
+
+ If unsure, say Y.
+
+config VIA_VELOCITY
+ tristate "VIA Velocity support"
+ depends on PCI
+ select CRC32
+ select CRC_CCITT
+ select MII
+ ---help---
+ If you have a VIA "Velocity" based network card say Y here.
+
+ To compile this driver as a module, choose M here. The module
+ will be called via-velocity.
+
+endif # NET_VENDOR_VIA
diff --git a/drivers/net/ethernet/via/Makefile b/drivers/net/ethernet/via/Makefile
new file mode 100644
index 0000000..46c5d4a
--- /dev/null
+++ b/drivers/net/ethernet/via/Makefile
@@ -0,0 +1,6 @@
+#
+# Makefile for the VIA device drivers.
+#
+
+obj-$(CONFIG_VIA_RHINE) += via-rhine.o
+obj-$(CONFIG_VIA_VELOCITY) += via-velocity.o
diff --git a/drivers/net/via-rhine.c b/drivers/net/ethernet/via/via-rhine.c
similarity index 100%
rename from drivers/net/via-rhine.c
rename to drivers/net/ethernet/via/via-rhine.c
diff --git a/drivers/net/via-velocity.c b/drivers/net/ethernet/via/via-velocity.c
similarity index 100%
rename from drivers/net/via-velocity.c
rename to drivers/net/ethernet/via/via-velocity.c
diff --git a/drivers/net/via-velocity.h b/drivers/net/ethernet/via/via-velocity.h
similarity index 100%
rename from drivers/net/via-velocity.h
rename to drivers/net/ethernet/via/via-velocity.h
--
1.7.6
^ permalink raw reply related [flat|nested] 21+ messages in thread* [net-next 07/10] eth16i: Move the Allied Telesis/Fujitsu drivers
2011-08-12 7:32 [net-next 00/10] drivers/net organize Ethernet drivers (4th series) Jeff Kirsher
` (5 preceding siblings ...)
2011-08-12 7:33 ` [net-next 06/10] via-*: Move the VIA drivers Jeff Kirsher
@ 2011-08-12 7:33 ` Jeff Kirsher
2011-08-12 7:33 ` [net-next 08/10] freescale: Move the Freescale drivers Jeff Kirsher
` (3 subsequent siblings)
10 siblings, 0 replies; 21+ messages in thread
From: Jeff Kirsher @ 2011-08-12 7:33 UTC (permalink / raw)
To: davem
Cc: Jeff Kirsher, netdev, gospo, sassmann, Shingo Fujimoto,
Yutaka Tamiya, Rene Schmit, Mika Kuoppala
Move the Allied Telesis/Fujitsu drivers into drivers/net/ethernet/fujitsu/
and make the necessary Kconfig and Makefile changes.
CC: Shingo Fujimoto <shingo@flab.fujitsu.co.jp>
CC: Yutaka Tamiya <tamy@flab.fujitsu.co.jp>
CC: Rene Schmit <rene@bss.lu>
CC: Mika Kuoppala <miku@iki.fi>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
MAINTAINERS | 2 +-
drivers/net/Kconfig | 40 ---------------
drivers/net/Makefile | 3 -
drivers/net/ethernet/Kconfig | 1 +
drivers/net/ethernet/Makefile | 1 +
drivers/net/ethernet/fujitsu/Kconfig | 53 ++++++++++++++++++++
drivers/net/ethernet/fujitsu/Makefile | 7 +++
drivers/net/{ => ethernet/fujitsu}/at1700.c | 0
drivers/net/{ => ethernet/fujitsu}/eth16i.c | 0
.../net/{pcmcia => ethernet/fujitsu}/fmvj18x_cs.c | 0
drivers/net/pcmcia/Kconfig | 10 ----
drivers/net/pcmcia/Makefile | 1 -
12 files changed, 63 insertions(+), 55 deletions(-)
create mode 100644 drivers/net/ethernet/fujitsu/Kconfig
create mode 100644 drivers/net/ethernet/fujitsu/Makefile
rename drivers/net/{ => ethernet/fujitsu}/at1700.c (100%)
rename drivers/net/{ => ethernet/fujitsu}/eth16i.c (100%)
rename drivers/net/{pcmcia => ethernet/fujitsu}/fmvj18x_cs.c (100%)
diff --git a/MAINTAINERS b/MAINTAINERS
index 51d9281..5b2ad6c 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -2525,7 +2525,7 @@ F: net/bridge/
ETHERTEAM 16I DRIVER
M: Mika Kuoppala <miku@iki.fi>
S: Maintained
-F: drivers/net/eth16i.c
+F: drivers/net/ethernet/fujitsu/eth16i.c
EXT2 FILE SYSTEM
M: Jan Kara <jack@suse.cz>
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index c1e491a..27f97b4e 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -428,18 +428,6 @@ config DNET
To compile this driver as a module, choose M here: the module
will be called dnet.
-config AT1700
- tristate "AT1700/1720 support (EXPERIMENTAL)"
- depends on (ISA || MCA_LEGACY) && EXPERIMENTAL
- select CRC32
- ---help---
- If you have a network (Ethernet) card of this type, say Y and read
- the Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>.
-
- To compile this driver as a module, choose M here. The module
- will be called at1700.
-
config HP100
tristate "HP 10/100VG PCLAN (ISA, EISA, PCI) support"
depends on ISA || EISA || PCI
@@ -451,34 +439,6 @@ config HP100
To compile this driver as a module, choose M here. The module
will be called hp100.
-config NET_ISA
- bool "Other ISA cards"
- depends on ISA
- ---help---
- If your network (Ethernet) card hasn't been mentioned yet and its
- bus system (that's the way the cards talks to the other components
- of your computer) is ISA (as opposed to EISA, VLB or PCI), say Y.
- Make sure you know the name of your card. Read the Ethernet-HOWTO,
- available from <http://www.tldp.org/docs.html#howto>.
-
- If unsure, say Y.
-
- Note that the answer to this question doesn't directly affect the
- kernel: saying N will just cause the configurator to skip all
- the remaining ISA network card questions. If you say Y, you will be
- asked for your specific card in the following questions.
-
-config ETH16I
- tristate "ICL EtherTeam 16i/32 support"
- depends on NET_ISA
- help
- If you have a network (Ethernet) card of this type, say Y and read
- the Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>.
-
- To compile this driver as a module, choose M here. The module
- will be called eth16i.
-
config NET_PCI
bool "EISA, VLB, PCI and on board controllers"
depends on ISA || EISA || PCI
diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index 7e1128f..07cad1a 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -96,10 +96,7 @@ obj-$(CONFIG_IFB) += ifb.o
obj-$(CONFIG_MACVLAN) += macvlan.o
obj-$(CONFIG_MACVTAP) += macvtap.o
obj-$(CONFIG_DEFXX) += defxx.o
-obj-$(CONFIG_AT1700) += at1700.o
obj-$(CONFIG_CPMAC) += cpmac.o
-
-obj-$(CONFIG_ETH16I) += eth16i.o
obj-$(CONFIG_EQUALIZER) += eql.o
obj-$(CONFIG_KORINA) += korina.o
obj-$(CONFIG_MIPS_SIM_NET) += mipsnet.o
diff --git a/drivers/net/ethernet/Kconfig b/drivers/net/ethernet/Kconfig
index bdc0df8..d3aff74 100644
--- a/drivers/net/ethernet/Kconfig
+++ b/drivers/net/ethernet/Kconfig
@@ -24,6 +24,7 @@ source "drivers/net/ethernet/dlink/Kconfig"
source "drivers/net/ethernet/emulex/Kconfig"
source "drivers/net/ethernet/neterion/Kconfig"
source "drivers/net/ethernet/faraday/Kconfig"
+source "drivers/net/ethernet/fujitsu/Kconfig"
source "drivers/net/ethernet/ibm/Kconfig"
source "drivers/net/ethernet/intel/Kconfig"
source "drivers/net/ethernet/i825xx/Kconfig"
diff --git a/drivers/net/ethernet/Makefile b/drivers/net/ethernet/Makefile
index ac60ac9..b098c5e 100644
--- a/drivers/net/ethernet/Makefile
+++ b/drivers/net/ethernet/Makefile
@@ -16,6 +16,7 @@ obj-$(CONFIG_NET_VENDOR_DLINK) += dlink/
obj-$(CONFIG_NET_VENDOR_EMULEX) += emulex/
obj-$(CONFIG_NET_VENDOR_EXAR) += neterion/
obj-$(CONFIG_NET_VENDOR_FARADAY) += faraday/
+obj-$(CONFIG_NET_VENDOR_FUJITSU) += fujitsu/
obj-$(CONFIG_NET_VENDOR_IBM) += ibm/
obj-$(CONFIG_NET_VENDOR_INTEL) += intel/
obj-$(CONFIG_NET_VENDOR_I825XX) += i825xx/
diff --git a/drivers/net/ethernet/fujitsu/Kconfig b/drivers/net/ethernet/fujitsu/Kconfig
new file mode 100644
index 0000000..2cd968e
--- /dev/null
+++ b/drivers/net/ethernet/fujitsu/Kconfig
@@ -0,0 +1,53 @@
+#
+# Fujitsu Network device configuration
+#
+
+config NET_VENDOR_FUJITSU
+ bool "Fujitsu devices"
+ depends on ISA || PCMCIA || ((ISA || MCA_LEGACY) && EXPERIMENTAL)
+ ---help---
+ If you have a network (Ethernet) card belonging to this class, say Y
+ and read the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>.
+
+ Note that the answer to this question doesn't directly affect the
+ the questions about Fujitsu cards. If you say Y, you will be asked for
+ your specific card in the following questions.
+
+if NET_VENDOR_FUJITSU
+
+config AT1700
+ tristate "AT1700/1720 support (EXPERIMENTAL)"
+ depends on (ISA || MCA_LEGACY) && EXPERIMENTAL
+ select CRC32
+ ---help---
+ If you have a network (Ethernet) card of this type, say Y and read
+ the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>.
+
+ To compile this driver as a module, choose M here. The module
+ will be called at1700.
+
+config PCMCIA_FMVJ18X
+ tristate "Fujitsu FMV-J18x PCMCIA support"
+ depends on PCMCIA
+ select CRC32
+ ---help---
+ Say Y here if you intend to attach a Fujitsu FMV-J18x or compatible
+ PCMCIA (PC-card) Ethernet card to your computer.
+
+ To compile this driver as a module, choose M here: the module will be
+ called fmvj18x_cs. If unsure, say N.
+
+config ETH16I
+ tristate "ICL EtherTeam 16i/32 support"
+ depends on ISA
+ ---help---
+ If you have a network (Ethernet) card of this type, say Y and read
+ the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>.
+
+ To compile this driver as a module, choose M here. The module
+ will be called eth16i.
+
+endif # NET_VENDOR_FUJITSU
diff --git a/drivers/net/ethernet/fujitsu/Makefile b/drivers/net/ethernet/fujitsu/Makefile
new file mode 100644
index 0000000..2730ae6
--- /dev/null
+++ b/drivers/net/ethernet/fujitsu/Makefile
@@ -0,0 +1,7 @@
+#
+# Makefile for the Fujitsu network device drivers.
+#
+
+obj-$(CONFIG_AT1700) += at1700.o
+obj-$(CONFIG_ETH16I) += eth16i.o
+obj-$(CONFIG_PCMCIA_FMVJ18X) += fmvj18x_cs.o
diff --git a/drivers/net/at1700.c b/drivers/net/ethernet/fujitsu/at1700.c
similarity index 100%
rename from drivers/net/at1700.c
rename to drivers/net/ethernet/fujitsu/at1700.c
diff --git a/drivers/net/eth16i.c b/drivers/net/ethernet/fujitsu/eth16i.c
similarity index 100%
rename from drivers/net/eth16i.c
rename to drivers/net/ethernet/fujitsu/eth16i.c
diff --git a/drivers/net/pcmcia/fmvj18x_cs.c b/drivers/net/ethernet/fujitsu/fmvj18x_cs.c
similarity index 100%
rename from drivers/net/pcmcia/fmvj18x_cs.c
rename to drivers/net/ethernet/fujitsu/fmvj18x_cs.c
diff --git a/drivers/net/pcmcia/Kconfig b/drivers/net/pcmcia/Kconfig
index f5a738f..80d291e 100644
--- a/drivers/net/pcmcia/Kconfig
+++ b/drivers/net/pcmcia/Kconfig
@@ -21,16 +21,6 @@ menuconfig NET_PCMCIA
if NET_PCMCIA && PCMCIA
-config PCMCIA_FMVJ18X
- tristate "Fujitsu FMV-J18x PCMCIA support"
- select CRC32
- help
- Say Y here if you intend to attach a Fujitsu FMV-J18x or compatible
- PCMCIA (PC-card) Ethernet card to your computer.
-
- To compile this driver as a module, choose M here: the module will be
- called fmvj18x_cs. If unsure, say N.
-
config PCMCIA_XIRC2PS
tristate "Xircom 16-bit PCMCIA support"
help
diff --git a/drivers/net/pcmcia/Makefile b/drivers/net/pcmcia/Makefile
index f9c9883..ccf5535 100644
--- a/drivers/net/pcmcia/Makefile
+++ b/drivers/net/pcmcia/Makefile
@@ -3,7 +3,6 @@
#
# 16-bit client drivers
-obj-$(CONFIG_PCMCIA_FMVJ18X) += fmvj18x_cs.o
obj-$(CONFIG_PCMCIA_XIRC2PS) += xirc2ps_cs.o
obj-$(CONFIG_ARCNET_COM20020_CS)+= com20020_cs.o
--
1.7.6
^ permalink raw reply related [flat|nested] 21+ messages in thread* [net-next 08/10] freescale: Move the Freescale drivers
2011-08-12 7:32 [net-next 00/10] drivers/net organize Ethernet drivers (4th series) Jeff Kirsher
` (6 preceding siblings ...)
2011-08-12 7:33 ` [net-next 07/10] eth16i: Move the Allied Telesis/Fujitsu drivers Jeff Kirsher
@ 2011-08-12 7:33 ` Jeff Kirsher
2011-08-12 7:33 ` [net-next 09/10] ks8*/ksz8*: Move the Micrel drivers Jeff Kirsher
` (2 subsequent siblings)
10 siblings, 0 replies; 21+ messages in thread
From: Jeff Kirsher @ 2011-08-12 7:33 UTC (permalink / raw)
To: davem
Cc: Jeff Kirsher, netdev, gospo, sassmann, Sandeep Gopalpet,
Andy Fleming, Shlomi Gridish, Li Yang, Pantelis Antoniou,
Vitaly Bordug, Dan Malek, Sylvain Munaut
Move the Freescale drivers into drivers/net/ethernet/freescale/ and
make the necessary Kconfig and Makefile changes.
CC: Sandeep Gopalpet <sandeep.kumar@freescale.com>
CC: Andy Fleming <afleming@freescale.com>
CC: Shlomi Gridish <gridish@freescale.com>
CC: Li Yang <leoli@freescale.com>
CC: Pantelis Antoniou <pantelis.antoniou@gmail.com>
CC: Vitaly Bordug <vbordug@ru.mvista.com>
CC: Dan Malek <dmalek@jlc.net>
CC: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
MAINTAINERS | 4 +-
drivers/net/Kconfig | 66 ---------------
drivers/net/Makefile | 18 ----
drivers/net/ethernet/Kconfig | 1 +
drivers/net/ethernet/Makefile | 1 +
drivers/net/ethernet/freescale/Kconfig | 88 ++++++++++++++++++++
drivers/net/ethernet/freescale/Makefile | 18 ++++
drivers/net/{ => ethernet/freescale}/fec.c | 0
drivers/net/{ => ethernet/freescale}/fec.h | 0
drivers/net/{ => ethernet/freescale}/fec_mpc52xx.c | 0
drivers/net/{ => ethernet/freescale}/fec_mpc52xx.h | 0
.../net/{ => ethernet/freescale}/fec_mpc52xx_phy.c | 0
.../net/{ => ethernet/freescale}/fs_enet/Kconfig | 2 +-
.../net/{ => ethernet/freescale}/fs_enet/Makefile | 0
drivers/net/{ => ethernet/freescale}/fs_enet/fec.h | 0
.../freescale}/fs_enet/fs_enet-main.c | 0
.../net/{ => ethernet/freescale}/fs_enet/fs_enet.h | 0
.../net/{ => ethernet/freescale}/fs_enet/mac-fcc.c | 0
.../net/{ => ethernet/freescale}/fs_enet/mac-fec.c | 0
.../net/{ => ethernet/freescale}/fs_enet/mac-scc.c | 0
.../{ => ethernet/freescale}/fs_enet/mii-bitbang.c | 0
.../net/{ => ethernet/freescale}/fs_enet/mii-fec.c | 0
drivers/net/{ => ethernet/freescale}/fsl_pq_mdio.c | 0
drivers/net/{ => ethernet/freescale}/fsl_pq_mdio.h | 0
drivers/net/{ => ethernet/freescale}/gianfar.c | 0
drivers/net/{ => ethernet/freescale}/gianfar.h | 0
.../net/{ => ethernet/freescale}/gianfar_ethtool.c | 0
drivers/net/{ => ethernet/freescale}/gianfar_ptp.c | 0
.../net/{ => ethernet/freescale}/gianfar_sysfs.c | 0
drivers/net/{ => ethernet/freescale}/ucc_geth.c | 0
drivers/net/{ => ethernet/freescale}/ucc_geth.h | 0
.../{ => ethernet/freescale}/ucc_geth_ethtool.c | 0
32 files changed, 111 insertions(+), 87 deletions(-)
create mode 100644 drivers/net/ethernet/freescale/Kconfig
create mode 100644 drivers/net/ethernet/freescale/Makefile
rename drivers/net/{ => ethernet/freescale}/fec.c (100%)
rename drivers/net/{ => ethernet/freescale}/fec.h (100%)
rename drivers/net/{ => ethernet/freescale}/fec_mpc52xx.c (100%)
rename drivers/net/{ => ethernet/freescale}/fec_mpc52xx.h (100%)
rename drivers/net/{ => ethernet/freescale}/fec_mpc52xx_phy.c (100%)
rename drivers/net/{ => ethernet/freescale}/fs_enet/Kconfig (91%)
rename drivers/net/{ => ethernet/freescale}/fs_enet/Makefile (100%)
rename drivers/net/{ => ethernet/freescale}/fs_enet/fec.h (100%)
rename drivers/net/{ => ethernet/freescale}/fs_enet/fs_enet-main.c (100%)
rename drivers/net/{ => ethernet/freescale}/fs_enet/fs_enet.h (100%)
rename drivers/net/{ => ethernet/freescale}/fs_enet/mac-fcc.c (100%)
rename drivers/net/{ => ethernet/freescale}/fs_enet/mac-fec.c (100%)
rename drivers/net/{ => ethernet/freescale}/fs_enet/mac-scc.c (100%)
rename drivers/net/{ => ethernet/freescale}/fs_enet/mii-bitbang.c (100%)
rename drivers/net/{ => ethernet/freescale}/fs_enet/mii-fec.c (100%)
rename drivers/net/{ => ethernet/freescale}/fsl_pq_mdio.c (100%)
rename drivers/net/{ => ethernet/freescale}/fsl_pq_mdio.h (100%)
rename drivers/net/{ => ethernet/freescale}/gianfar.c (100%)
rename drivers/net/{ => ethernet/freescale}/gianfar.h (100%)
rename drivers/net/{ => ethernet/freescale}/gianfar_ethtool.c (100%)
rename drivers/net/{ => ethernet/freescale}/gianfar_ptp.c (100%)
rename drivers/net/{ => ethernet/freescale}/gianfar_sysfs.c (100%)
rename drivers/net/{ => ethernet/freescale}/ucc_geth.c (100%)
rename drivers/net/{ => ethernet/freescale}/ucc_geth.h (100%)
rename drivers/net/{ => ethernet/freescale}/ucc_geth_ethtool.c (100%)
diff --git a/MAINTAINERS b/MAINTAINERS
index 5b2ad6c..77ca430 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -2689,7 +2689,7 @@ M: Vitaly Bordug <vbordug@ru.mvista.com>
L: linuxppc-dev@lists.ozlabs.org
L: netdev@vger.kernel.org
S: Maintained
-F: drivers/net/fs_enet/
+F: drivers/net/ethernet/freescale/fs_enet/
F: include/linux/fs_enet_pd.h
FREESCALE QUICC ENGINE LIBRARY
@@ -2711,7 +2711,7 @@ M: Li Yang <leoli@freescale.com>
L: netdev@vger.kernel.org
L: linuxppc-dev@lists.ozlabs.org
S: Maintained
-F: drivers/net/ucc_geth*
+F: drivers/net/ethernet/freescale/ucc_geth*
FREESCALE QUICC ENGINE UCC UART DRIVER
M: Timur Tabi <timur@freescale.com>
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index 27f97b4e..b645a73 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -605,39 +605,6 @@ config NET_POCKET
the questions about this class of network devices. If you say Y, you
will be asked for your specific device in the following questions.
-config FEC
- bool "FEC ethernet controller (of ColdFire and some i.MX CPUs)"
- depends on M523x || M527x || M5272 || M528x || M520x || M532x || \
- IMX_HAVE_PLATFORM_FEC || MXS_HAVE_PLATFORM_FEC
- default IMX_HAVE_PLATFORM_FEC || MXS_HAVE_PLATFORM_FEC if ARM
- select PHYLIB
- help
- Say Y here if you want to use the built-in 10/100 Fast ethernet
- controller on some Motorola ColdFire and Freescale i.MX processors.
-
-config FEC_MPC52xx
- tristate "MPC52xx FEC driver"
- depends on PPC_MPC52xx && PPC_BESTCOMM
- select CRC32
- select PHYLIB
- select PPC_BESTCOMM_FEC
- ---help---
- This option enables support for the MPC5200's on-chip
- Fast Ethernet Controller
- If compiled as module, it will be called fec_mpc52xx.
-
-config FEC_MPC52xx_MDIO
- bool "MPC52xx FEC MDIO bus driver"
- depends on FEC_MPC52xx
- default y
- ---help---
- The MPC5200's FEC can connect to the Ethernet either with
- an external MII PHY chip or 10 Mbps 7-wire interface
- (Motorola? industry standard).
- If your board uses an external PHY connected to FEC, enable this.
- If not sure, enable.
- If compiled as module, it will be called fec_mpc52xx_phy.
-
config XILINX_EMACLITE
tristate "Xilinx 10/100 Ethernet Lite support"
depends on PPC32 || MICROBLAZE
@@ -651,9 +618,6 @@ config LANTIQ_ETOP
help
Support for the MII0 inside the Lantiq SoC
-
-source "drivers/net/fs_enet/Kconfig"
-
source "drivers/net/octeon/Kconfig"
endif # NET_ETHERNET
@@ -769,36 +733,6 @@ config GELIC_WIRELESS
the driver automatically distinguishes the models, you can
safely enable this option even if you have a wireless-less model.
-config FSL_PQ_MDIO
- tristate "Freescale PQ MDIO"
- depends on FSL_SOC
- select PHYLIB
- help
- This driver supports the MDIO bus used by the gianfar and UCC drivers.
-
-config GIANFAR
- tristate "Gianfar Ethernet"
- depends on FSL_SOC
- select FSL_PQ_MDIO
- select PHYLIB
- select CRC32
- help
- This driver supports the Gigabit TSEC on the MPC83xx, MPC85xx,
- and MPC86xx family of chips, and the FEC on the 8540.
-
-config UCC_GETH
- tristate "Freescale QE Gigabit Ethernet"
- depends on QUICC_ENGINE
- select FSL_PQ_MDIO
- select PHYLIB
- help
- This driver supports the Gigabit Ethernet mode of the QUICC Engine,
- which is available on some Freescale SOCs.
-
-config UGETH_TX_ON_DEMAND
- bool "Transmit on Demand support"
- depends on UCC_GETH
-
config XILINX_LL_TEMAC
tristate "Xilinx LL TEMAC (LocalLink Tri-mode Ethernet MAC) driver"
depends on PPC || MICROBLAZE
diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index 07cad1a..39fe730 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -13,20 +13,9 @@ obj-$(CONFIG_TI_DAVINCI_CPDMA) += davinci_cpdma.o
obj-$(CONFIG_IP1000) += ipg.o
obj-$(CONFIG_CAN) += can/
obj-$(CONFIG_BONDING) += bonding/
-obj-$(CONFIG_GIANFAR) += gianfar_driver.o
-obj-$(CONFIG_PTP_1588_CLOCK_GIANFAR) += gianfar_ptp.o
obj-$(CONFIG_JME) += jme.o
obj-$(CONFIG_VMXNET3) += vmxnet3/
-gianfar_driver-objs := gianfar.o \
- gianfar_ethtool.o \
- gianfar_sysfs.o
-
-obj-$(CONFIG_UCC_GETH) += ucc_geth_driver.o
-ucc_geth_driver-objs := ucc_geth.o ucc_geth_ethtool.o
-
-obj-$(CONFIG_FSL_PQ_MDIO) += fsl_pq_mdio.o
-
#
# link order important here
#
@@ -63,11 +52,6 @@ obj-$(CONFIG_HAMACHI) += hamachi.o
obj-$(CONFIG_NET) += Space.o loopback.o
obj-$(CONFIG_NET_SB1000) += sb1000.o
obj-$(CONFIG_HP100) += hp100.o
-obj-$(CONFIG_FEC) += fec.o
-obj-$(CONFIG_FEC_MPC52xx) += fec_mpc52xx.o
-ifeq ($(CONFIG_FEC_MPC52xx_MDIO),y)
- obj-$(CONFIG_FEC_MPC52xx) += fec_mpc52xx_phy.o
-endif
obj-$(CONFIG_FORCEDETH) += forcedeth.o
obj-$(CONFIG_TSI108_ETH) += tsi108_eth.o
@@ -139,8 +123,6 @@ obj-$(CONFIG_ETRAX_ETHERNET) += cris/
obj-$(CONFIG_NETCONSOLE) += netconsole.o
-obj-$(CONFIG_FS_ENET) += fs_enet/
-
obj-$(CONFIG_VIRTIO_NET) += virtio_net.o
obj-$(CONFIG_WIMAX) += wimax/
diff --git a/drivers/net/ethernet/Kconfig b/drivers/net/ethernet/Kconfig
index d3aff74..924c287 100644
--- a/drivers/net/ethernet/Kconfig
+++ b/drivers/net/ethernet/Kconfig
@@ -24,6 +24,7 @@ source "drivers/net/ethernet/dlink/Kconfig"
source "drivers/net/ethernet/emulex/Kconfig"
source "drivers/net/ethernet/neterion/Kconfig"
source "drivers/net/ethernet/faraday/Kconfig"
+source "drivers/net/ethernet/freescale/Kconfig"
source "drivers/net/ethernet/fujitsu/Kconfig"
source "drivers/net/ethernet/ibm/Kconfig"
source "drivers/net/ethernet/intel/Kconfig"
diff --git a/drivers/net/ethernet/Makefile b/drivers/net/ethernet/Makefile
index b098c5e..025d7b7 100644
--- a/drivers/net/ethernet/Makefile
+++ b/drivers/net/ethernet/Makefile
@@ -16,6 +16,7 @@ obj-$(CONFIG_NET_VENDOR_DLINK) += dlink/
obj-$(CONFIG_NET_VENDOR_EMULEX) += emulex/
obj-$(CONFIG_NET_VENDOR_EXAR) += neterion/
obj-$(CONFIG_NET_VENDOR_FARADAY) += faraday/
+obj-$(CONFIG_NET_VENDOR_FREESCALE) += freescale/
obj-$(CONFIG_NET_VENDOR_FUJITSU) += fujitsu/
obj-$(CONFIG_NET_VENDOR_IBM) += ibm/
obj-$(CONFIG_NET_VENDOR_INTEL) += intel/
diff --git a/drivers/net/ethernet/freescale/Kconfig b/drivers/net/ethernet/freescale/Kconfig
new file mode 100644
index 0000000..2fd2c61
--- /dev/null
+++ b/drivers/net/ethernet/freescale/Kconfig
@@ -0,0 +1,88 @@
+#
+# Freescale device configuration
+#
+
+config NET_VENDOR_FREESCALE
+ bool "Freescale devices"
+ depends on FSL_SOC || QUICC_ENGINE || CPM1 || CPM2 || PPC_MPC512x || \
+ M523x || M527x || M5272 || M528x || M520x || M532x || \
+ IMX_HAVE_PLATFORM_FEC || MXS_HAVE_PLATFORM_FEC || \
+ (PPC_MPC52xx && PPC_BESTCOMM)
+ ---help---
+ If you have a network (Ethernet) card belonging to this class, say Y
+ and read the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>.
+
+ Note that the answer to this question doesn't directly affect the
+ kernel: saying N will just cause the configurator to skip all
+ the questions about IBM devices. If you say Y, you will be asked for
+ your specific card in the following questions.
+
+if NET_VENDOR_FREESCALE
+
+config FEC
+ bool "FEC ethernet controller (of ColdFire and some i.MX CPUs)"
+ depends on (M523x || M527x || M5272 || M528x || M520x || M532x || \
+ IMX_HAVE_PLATFORM_FEC || MXS_HAVE_PLATFORM_FEC)
+ default IMX_HAVE_PLATFORM_FEC || MXS_HAVE_PLATFORM_FEC if ARM
+ select PHYLIB
+ ---help---
+ Say Y here if you want to use the built-in 10/100 Fast ethernet
+ controller on some Motorola ColdFire and Freescale i.MX processors.
+
+config FEC_MPC52xx
+ tristate "FEC MPC52xx driver"
+ depends on PPC_MPC52xx && PPC_BESTCOMM
+ select CRC32
+ select PHYLIB
+ select PPC_BESTCOMM_FEC
+ ---help---
+ This option enables support for the MPC5200's on-chip
+ Fast Ethernet Controller
+ If compiled as module, it will be called fec_mpc52xx.
+
+config FEC_MPC52xx_MDIO
+ bool "FEC MPC52xx MDIO bus driver"
+ depends on FEC_MPC52xx
+ default y
+ ---help---
+ The MPC5200's FEC can connect to the Ethernet either with
+ an external MII PHY chip or 10 Mbps 7-wire interface
+ (Motorola? industry standard).
+ If your board uses an external PHY connected to FEC, enable this.
+ If not sure, enable.
+ If compiled as module, it will be called fec_mpc52xx_phy.
+
+source "drivers/net/ethernet/freescale/fs_enet/Kconfig"
+
+config FSL_PQ_MDIO
+ tristate "Freescale PQ MDIO"
+ depends on FSL_SOC
+ select PHYLIB
+ ---help---
+ This driver supports the MDIO bus used by the gianfar and UCC drivers.
+
+config UCC_GETH
+ tristate "Freescale QE Gigabit Ethernet"
+ depends on QUICC_ENGINE
+ select FSL_PQ_MDIO
+ select PHYLIB
+ ---help---
+ This driver supports the Gigabit Ethernet mode of the QUICC Engine,
+ which is available on some Freescale SOCs.
+
+config UGETH_TX_ON_DEMAND
+ bool "Transmit on Demand support"
+ depends on UCC_GETH
+
+config GIANFAR
+ tristate "Gianfar Ethernet"
+ depends on FSL_SOC
+ select FSL_PQ_MDIO
+ select PHYLIB
+ select CRC32
+ ---help---
+ This driver supports the Gigabit TSEC on the MPC83xx, MPC85xx,
+ and MPC86xx family of chips, and the FEC on the 8540.
+
+endif # NET_VENDOR_FREESCALE
diff --git a/drivers/net/ethernet/freescale/Makefile b/drivers/net/ethernet/freescale/Makefile
new file mode 100644
index 0000000..1752488
--- /dev/null
+++ b/drivers/net/ethernet/freescale/Makefile
@@ -0,0 +1,18 @@
+#
+# Makefile for the Freescale network device drivers.
+#
+
+obj-$(CONFIG_FEC) += fec.o
+obj-$(CONFIG_FEC_MPC52xx) += fec_mpc52xx.o
+ifeq ($(CONFIG_FEC_MPC52xx_MDIO),y)
+ obj-$(CONFIG_FEC_MPC52xx) += fec_mpc52xx_phy.o
+endif
+obj-$(CONFIG_FS_ENET) += fs_enet/
+obj-$(CONFIG_FSL_PQ_MDIO) += fsl_pq_mdio.o
+obj-$(CONFIG_GIANFAR) += gianfar_driver.o
+obj-$(CONFIG_PTP_1588_CLOCK_GIANFAR) += gianfar_ptp.o
+gianfar_driver-objs := gianfar.o \
+ gianfar_ethtool.o \
+ gianfar_sysfs.o
+obj-$(CONFIG_UCC_GETH) += ucc_geth_driver.o
+ucc_geth_driver-objs := ucc_geth.o ucc_geth_ethtool.o
diff --git a/drivers/net/fec.c b/drivers/net/ethernet/freescale/fec.c
similarity index 100%
rename from drivers/net/fec.c
rename to drivers/net/ethernet/freescale/fec.c
diff --git a/drivers/net/fec.h b/drivers/net/ethernet/freescale/fec.h
similarity index 100%
rename from drivers/net/fec.h
rename to drivers/net/ethernet/freescale/fec.h
diff --git a/drivers/net/fec_mpc52xx.c b/drivers/net/ethernet/freescale/fec_mpc52xx.c
similarity index 100%
rename from drivers/net/fec_mpc52xx.c
rename to drivers/net/ethernet/freescale/fec_mpc52xx.c
diff --git a/drivers/net/fec_mpc52xx.h b/drivers/net/ethernet/freescale/fec_mpc52xx.h
similarity index 100%
rename from drivers/net/fec_mpc52xx.h
rename to drivers/net/ethernet/freescale/fec_mpc52xx.h
diff --git a/drivers/net/fec_mpc52xx_phy.c b/drivers/net/ethernet/freescale/fec_mpc52xx_phy.c
similarity index 100%
rename from drivers/net/fec_mpc52xx_phy.c
rename to drivers/net/ethernet/freescale/fec_mpc52xx_phy.c
diff --git a/drivers/net/fs_enet/Kconfig b/drivers/net/ethernet/freescale/fs_enet/Kconfig
similarity index 91%
rename from drivers/net/fs_enet/Kconfig
rename to drivers/net/ethernet/freescale/fs_enet/Kconfig
index fc073b5..be92229 100644
--- a/drivers/net/fs_enet/Kconfig
+++ b/drivers/net/ethernet/freescale/fs_enet/Kconfig
@@ -1,6 +1,6 @@
config FS_ENET
tristate "Freescale Ethernet Driver"
- depends on CPM1 || CPM2 || PPC_MPC512x
+ depends on NET_VENDOR_FREESCALE && (CPM1 || CPM2 || PPC_MPC512x)
select MII
select PHYLIB
diff --git a/drivers/net/fs_enet/Makefile b/drivers/net/ethernet/freescale/fs_enet/Makefile
similarity index 100%
rename from drivers/net/fs_enet/Makefile
rename to drivers/net/ethernet/freescale/fs_enet/Makefile
diff --git a/drivers/net/fs_enet/fec.h b/drivers/net/ethernet/freescale/fs_enet/fec.h
similarity index 100%
rename from drivers/net/fs_enet/fec.h
rename to drivers/net/ethernet/freescale/fs_enet/fec.h
diff --git a/drivers/net/fs_enet/fs_enet-main.c b/drivers/net/ethernet/freescale/fs_enet/fs_enet-main.c
similarity index 100%
rename from drivers/net/fs_enet/fs_enet-main.c
rename to drivers/net/ethernet/freescale/fs_enet/fs_enet-main.c
diff --git a/drivers/net/fs_enet/fs_enet.h b/drivers/net/ethernet/freescale/fs_enet/fs_enet.h
similarity index 100%
rename from drivers/net/fs_enet/fs_enet.h
rename to drivers/net/ethernet/freescale/fs_enet/fs_enet.h
diff --git a/drivers/net/fs_enet/mac-fcc.c b/drivers/net/ethernet/freescale/fs_enet/mac-fcc.c
similarity index 100%
rename from drivers/net/fs_enet/mac-fcc.c
rename to drivers/net/ethernet/freescale/fs_enet/mac-fcc.c
diff --git a/drivers/net/fs_enet/mac-fec.c b/drivers/net/ethernet/freescale/fs_enet/mac-fec.c
similarity index 100%
rename from drivers/net/fs_enet/mac-fec.c
rename to drivers/net/ethernet/freescale/fs_enet/mac-fec.c
diff --git a/drivers/net/fs_enet/mac-scc.c b/drivers/net/ethernet/freescale/fs_enet/mac-scc.c
similarity index 100%
rename from drivers/net/fs_enet/mac-scc.c
rename to drivers/net/ethernet/freescale/fs_enet/mac-scc.c
diff --git a/drivers/net/fs_enet/mii-bitbang.c b/drivers/net/ethernet/freescale/fs_enet/mii-bitbang.c
similarity index 100%
rename from drivers/net/fs_enet/mii-bitbang.c
rename to drivers/net/ethernet/freescale/fs_enet/mii-bitbang.c
diff --git a/drivers/net/fs_enet/mii-fec.c b/drivers/net/ethernet/freescale/fs_enet/mii-fec.c
similarity index 100%
rename from drivers/net/fs_enet/mii-fec.c
rename to drivers/net/ethernet/freescale/fs_enet/mii-fec.c
diff --git a/drivers/net/fsl_pq_mdio.c b/drivers/net/ethernet/freescale/fsl_pq_mdio.c
similarity index 100%
rename from drivers/net/fsl_pq_mdio.c
rename to drivers/net/ethernet/freescale/fsl_pq_mdio.c
diff --git a/drivers/net/fsl_pq_mdio.h b/drivers/net/ethernet/freescale/fsl_pq_mdio.h
similarity index 100%
rename from drivers/net/fsl_pq_mdio.h
rename to drivers/net/ethernet/freescale/fsl_pq_mdio.h
diff --git a/drivers/net/gianfar.c b/drivers/net/ethernet/freescale/gianfar.c
similarity index 100%
rename from drivers/net/gianfar.c
rename to drivers/net/ethernet/freescale/gianfar.c
diff --git a/drivers/net/gianfar.h b/drivers/net/ethernet/freescale/gianfar.h
similarity index 100%
rename from drivers/net/gianfar.h
rename to drivers/net/ethernet/freescale/gianfar.h
diff --git a/drivers/net/gianfar_ethtool.c b/drivers/net/ethernet/freescale/gianfar_ethtool.c
similarity index 100%
rename from drivers/net/gianfar_ethtool.c
rename to drivers/net/ethernet/freescale/gianfar_ethtool.c
diff --git a/drivers/net/gianfar_ptp.c b/drivers/net/ethernet/freescale/gianfar_ptp.c
similarity index 100%
rename from drivers/net/gianfar_ptp.c
rename to drivers/net/ethernet/freescale/gianfar_ptp.c
diff --git a/drivers/net/gianfar_sysfs.c b/drivers/net/ethernet/freescale/gianfar_sysfs.c
similarity index 100%
rename from drivers/net/gianfar_sysfs.c
rename to drivers/net/ethernet/freescale/gianfar_sysfs.c
diff --git a/drivers/net/ucc_geth.c b/drivers/net/ethernet/freescale/ucc_geth.c
similarity index 100%
rename from drivers/net/ucc_geth.c
rename to drivers/net/ethernet/freescale/ucc_geth.c
diff --git a/drivers/net/ucc_geth.h b/drivers/net/ethernet/freescale/ucc_geth.h
similarity index 100%
rename from drivers/net/ucc_geth.h
rename to drivers/net/ethernet/freescale/ucc_geth.h
diff --git a/drivers/net/ucc_geth_ethtool.c b/drivers/net/ethernet/freescale/ucc_geth_ethtool.c
similarity index 100%
rename from drivers/net/ucc_geth_ethtool.c
rename to drivers/net/ethernet/freescale/ucc_geth_ethtool.c
--
1.7.6
^ permalink raw reply related [flat|nested] 21+ messages in thread* [net-next 09/10] ks8*/ksz8*: Move the Micrel drivers
2011-08-12 7:32 [net-next 00/10] drivers/net organize Ethernet drivers (4th series) Jeff Kirsher
` (7 preceding siblings ...)
2011-08-12 7:33 ` [net-next 08/10] freescale: Move the Freescale drivers Jeff Kirsher
@ 2011-08-12 7:33 ` Jeff Kirsher
2011-08-12 7:33 ` [net-next 10/10] toshiba: Move the Toshiba drivers Jeff Kirsher
2011-08-12 8:20 ` [net-next 00/10] drivers/net organize Ethernet drivers (4th series) David Miller
10 siblings, 0 replies; 21+ messages in thread
From: Jeff Kirsher @ 2011-08-12 7:33 UTC (permalink / raw)
To: davem; +Cc: Jeff Kirsher, netdev, gospo, sassmann, Ben Dooks, Tristram Ha
Move the Micrel drivers into drivers/net/ethernet/micrel/ and
make the necessary Kconfig and Makefile changes.
CC: Ben Dooks <ben@simtec.co.uk>
CC: Tristram Ha <Tristram.Ha@micrel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
drivers/net/Kconfig | 35 ------------
drivers/net/Makefile | 4 --
drivers/net/arm/Kconfig | 8 ---
drivers/net/arm/Makefile | 1 -
drivers/net/ethernet/Kconfig | 1 +
drivers/net/ethernet/Makefile | 1 +
drivers/net/ethernet/micrel/Kconfig | 64 ++++++++++++++++++++++
drivers/net/ethernet/micrel/Makefile | 9 +++
drivers/net/{arm => ethernet/micrel}/ks8695net.c | 0
drivers/net/{arm => ethernet/micrel}/ks8695net.h | 0
drivers/net/{ => ethernet/micrel}/ks8842.c | 0
drivers/net/{ => ethernet/micrel}/ks8851.c | 0
drivers/net/{ => ethernet/micrel}/ks8851.h | 0
drivers/net/{ => ethernet/micrel}/ks8851_mll.c | 0
drivers/net/{ => ethernet/micrel}/ksz884x.c | 0
15 files changed, 75 insertions(+), 48 deletions(-)
create mode 100644 drivers/net/ethernet/micrel/Kconfig
create mode 100644 drivers/net/ethernet/micrel/Makefile
rename drivers/net/{arm => ethernet/micrel}/ks8695net.c (100%)
rename drivers/net/{arm => ethernet/micrel}/ks8695net.h (100%)
rename drivers/net/{ => ethernet/micrel}/ks8842.c (100%)
rename drivers/net/{ => ethernet/micrel}/ks8851.c (100%)
rename drivers/net/{ => ethernet/micrel}/ks8851.h (100%)
rename drivers/net/{ => ethernet/micrel}/ks8851_mll.c (100%)
rename drivers/net/{ => ethernet/micrel}/ksz884x.c (100%)
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index b645a73..a6edd354 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -467,17 +467,6 @@ config ADAPTEC_STARFIRE
To compile this driver as a module, choose M here: the module
will be called starfire. This is recommended.
-config KSZ884X_PCI
- tristate "Micrel KSZ8841/2 PCI"
- depends on NET_PCI && PCI
- select MII
- select CRC32
- help
- This PCI driver is for Micrel KSZ8841/KSZ8842 PCI Ethernet chip.
-
- To compile this driver as a module, choose M here. The module
- will be called ksz884x.
-
config FORCEDETH
tristate "nForce Ethernet support"
depends on NET_PCI && PCI
@@ -550,30 +539,6 @@ config TLAN
Please email feedback to <torben.mathiasen@compaq.com>.
-config KS8842
- tristate "Micrel KSZ8841/42 with generic bus interface"
- depends on HAS_IOMEM && DMA_ENGINE
- help
- This platform driver is for KSZ8841(1-port) / KS8842(2-port)
- ethernet switch chip (managed, VLAN, QoS) from Micrel or
- Timberdale(FPGA).
-
-config KS8851
- tristate "Micrel KS8851 SPI"
- depends on SPI
- select MII
- select CRC32
- help
- SPI driver for Micrel KS8851 SPI attached network chip.
-
-config KS8851_MLL
- tristate "Micrel KS8851 MLL"
- depends on HAS_IOMEM
- select MII
- help
- This platform driver is for Micrel KS8851 Address/data bus
- multiplexed network chip.
-
config CPMAC
tristate "TI AR7 CPMAC Ethernet support (EXPERIMENTAL)"
depends on NET_ETHERNET && EXPERIMENTAL && AR7
diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index 39fe730..e448e6e 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -36,10 +36,6 @@ gelic_wireless-$(CONFIG_GELIC_WIRELESS) += ps3_gelic_wireless.o
ps3_gelic-objs += ps3_gelic_net.o $(gelic_wireless-y)
obj-$(CONFIG_TC35815) += tc35815.o
obj-$(CONFIG_SKFP) += skfp/
-obj-$(CONFIG_KS8842) += ks8842.o
-obj-$(CONFIG_KS8851) += ks8851.o
-obj-$(CONFIG_KS8851_MLL) += ks8851_mll.o
-obj-$(CONFIG_KSZ884X_PCI) += ksz884x.o
obj-$(CONFIG_ADAPTEC_STARFIRE) += starfire.o
obj-$(CONFIG_RIONET) += rionet.o
obj-$(CONFIG_SH_ETH) += sh_eth.o
diff --git a/drivers/net/arm/Kconfig b/drivers/net/arm/Kconfig
index b6f7302..4f748cc 100644
--- a/drivers/net/arm/Kconfig
+++ b/drivers/net/arm/Kconfig
@@ -11,14 +11,6 @@ config ARM_AT91_ETHER
If you wish to compile a kernel for the AT91RM9200 and enable
ethernet support, then you should always answer Y to this.
-config ARM_KS8695_ETHER
- tristate "KS8695 Ethernet support"
- depends on ARM && ARCH_KS8695
- select MII
- help
- If you wish to compile a kernel for the KS8695 and want to
- use the internal ethernet then you should answer Y to this.
-
config EP93XX_ETH
tristate "EP93xx Ethernet support"
depends on ARM && ARCH_EP93XX
diff --git a/drivers/net/arm/Makefile b/drivers/net/arm/Makefile
index a2532e6..316b06c 100644
--- a/drivers/net/arm/Makefile
+++ b/drivers/net/arm/Makefile
@@ -4,6 +4,5 @@
#
obj-$(CONFIG_ARM_AT91_ETHER) += at91_ether.o
-obj-$(CONFIG_ARM_KS8695_ETHER) += ks8695net.o
obj-$(CONFIG_EP93XX_ETH) += ep93xx_eth.o
obj-$(CONFIG_W90P910_ETH) += w90p910_ether.o
diff --git a/drivers/net/ethernet/Kconfig b/drivers/net/ethernet/Kconfig
index 924c287..d90f47f3 100644
--- a/drivers/net/ethernet/Kconfig
+++ b/drivers/net/ethernet/Kconfig
@@ -32,6 +32,7 @@ source "drivers/net/ethernet/i825xx/Kconfig"
source "drivers/net/ethernet/xscale/Kconfig"
source "drivers/net/ethernet/marvell/Kconfig"
source "drivers/net/ethernet/mellanox/Kconfig"
+source "drivers/net/ethernet/micrel/Kconfig"
source "drivers/net/ethernet/myricom/Kconfig"
source "drivers/net/ethernet/natsemi/Kconfig"
source "drivers/net/ethernet/8390/Kconfig"
diff --git a/drivers/net/ethernet/Makefile b/drivers/net/ethernet/Makefile
index 025d7b7..cf27ae0 100644
--- a/drivers/net/ethernet/Makefile
+++ b/drivers/net/ethernet/Makefile
@@ -24,6 +24,7 @@ obj-$(CONFIG_NET_VENDOR_I825XX) += i825xx/
obj-$(CONFIG_NET_VENDOR_XSCALE) += xscale/
obj-$(CONFIG_NET_VENDOR_MARVELL) += marvell/
obj-$(CONFIG_NET_VENDOR_MELLANOX) += mellanox/
+obj-$(CONFIG_NET_VENDOR_MICREL) += micrel/
obj-$(CONFIG_NET_VENDOR_MYRI) += myricom/
obj-$(CONFIG_NET_VENDOR_NATSEMI) += natsemi/
obj-$(CONFIG_NET_VENDOR_OKI) += oki-semi/
diff --git a/drivers/net/ethernet/micrel/Kconfig b/drivers/net/ethernet/micrel/Kconfig
new file mode 100644
index 0000000..4227de6
--- /dev/null
+++ b/drivers/net/ethernet/micrel/Kconfig
@@ -0,0 +1,64 @@
+#
+# Micrel device configuration
+#
+
+config NET_VENDOR_MICREL
+ bool "Micrel devices"
+ depends on (HAS_IOMEM && DMA_ENGINE) || SPI || PCI || HAS_IOMEM || \
+ (ARM && ARCH_KS8695)
+ ---help---
+ If you have a network (Ethernet) card belonging to this class, say Y
+ and read the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>.
+
+ Note that the answer to this question doesn't directly affect the
+ kernel: saying N will just cause the configurator to skip all
+ the questions about Micrel devices. If you say Y, you will be asked
+ for your specific card in the following questions.
+
+if NET_VENDOR_MICREL
+
+config ARM_KS8695_ETHER
+ tristate "KS8695 Ethernet support"
+ depends on ARM && ARCH_KS8695
+ select MII
+ ---help---
+ If you wish to compile a kernel for the KS8695 and want to
+ use the internal ethernet then you should answer Y to this.
+
+config KS8842
+ tristate "Micrel KSZ8841/42 with generic bus interface"
+ depends on HAS_IOMEM && DMA_ENGINE
+ ---help---
+ This platform driver is for KSZ8841(1-port) / KS8842(2-port)
+ ethernet switch chip (managed, VLAN, QoS) from Micrel or
+ Timberdale(FPGA).
+
+config KS8851
+ tristate "Micrel KS8851 SPI"
+ depends on SPI
+ select MII
+ select CRC32
+ ---help---
+ SPI driver for Micrel KS8851 SPI attached network chip.
+
+config KS8851_MLL
+ tristate "Micrel KS8851 MLL"
+ depends on HAS_IOMEM
+ select MII
+ ---help---
+ This platform driver is for Micrel KS8851 Address/data bus
+ multiplexed network chip.
+
+config KSZ884X_PCI
+ tristate "Micrel KSZ8841/2 PCI"
+ depends on PCI
+ select MII
+ select CRC32
+ ---help---
+ This PCI driver is for Micrel KSZ8841/KSZ8842 PCI Ethernet chip.
+
+ To compile this driver as a module, choose M here. The module
+ will be called ksz884x.
+
+endif # NET_VENDOR_MICREL
diff --git a/drivers/net/ethernet/micrel/Makefile b/drivers/net/ethernet/micrel/Makefile
new file mode 100644
index 0000000..c83e4bc
--- /dev/null
+++ b/drivers/net/ethernet/micrel/Makefile
@@ -0,0 +1,9 @@
+#
+# Makefile for the Micrel network device drivers.
+#
+
+obj-$(CONFIG_ARM_KS8695_ETHER) += ks8695net.o
+obj-$(CONFIG_KS8842) += ks8842.o
+obj-$(CONFIG_KS8851) += ks8851.o
+obj-$(CONFIG_KS8851_MLL) += ks8851_mll.o
+obj-$(CONFIG_KSZ884X_PCI) += ksz884x.o
diff --git a/drivers/net/arm/ks8695net.c b/drivers/net/ethernet/micrel/ks8695net.c
similarity index 100%
rename from drivers/net/arm/ks8695net.c
rename to drivers/net/ethernet/micrel/ks8695net.c
diff --git a/drivers/net/arm/ks8695net.h b/drivers/net/ethernet/micrel/ks8695net.h
similarity index 100%
rename from drivers/net/arm/ks8695net.h
rename to drivers/net/ethernet/micrel/ks8695net.h
diff --git a/drivers/net/ks8842.c b/drivers/net/ethernet/micrel/ks8842.c
similarity index 100%
rename from drivers/net/ks8842.c
rename to drivers/net/ethernet/micrel/ks8842.c
diff --git a/drivers/net/ks8851.c b/drivers/net/ethernet/micrel/ks8851.c
similarity index 100%
rename from drivers/net/ks8851.c
rename to drivers/net/ethernet/micrel/ks8851.c
diff --git a/drivers/net/ks8851.h b/drivers/net/ethernet/micrel/ks8851.h
similarity index 100%
rename from drivers/net/ks8851.h
rename to drivers/net/ethernet/micrel/ks8851.h
diff --git a/drivers/net/ks8851_mll.c b/drivers/net/ethernet/micrel/ks8851_mll.c
similarity index 100%
rename from drivers/net/ks8851_mll.c
rename to drivers/net/ethernet/micrel/ks8851_mll.c
diff --git a/drivers/net/ksz884x.c b/drivers/net/ethernet/micrel/ksz884x.c
similarity index 100%
rename from drivers/net/ksz884x.c
rename to drivers/net/ethernet/micrel/ksz884x.c
--
1.7.6
^ permalink raw reply related [flat|nested] 21+ messages in thread* [net-next 10/10] toshiba: Move the Toshiba drivers
2011-08-12 7:32 [net-next 00/10] drivers/net organize Ethernet drivers (4th series) Jeff Kirsher
` (8 preceding siblings ...)
2011-08-12 7:33 ` [net-next 09/10] ks8*/ksz8*: Move the Micrel drivers Jeff Kirsher
@ 2011-08-12 7:33 ` Jeff Kirsher
2011-08-12 8:22 ` Jens Osterkamp
2011-08-12 8:20 ` [net-next 00/10] drivers/net organize Ethernet drivers (4th series) David Miller
10 siblings, 1 reply; 21+ messages in thread
From: Jeff Kirsher @ 2011-08-12 7:33 UTC (permalink / raw)
To: davem
Cc: Jeff Kirsher, netdev, gospo, sassmann, Geoff Levand,
Jens Osterkamp, Ishizaki Kou
Move the Toshiba ethernet drivers into drivers/net/ethernet/toshiba
and make the necessary Kconfig and Makefile changes.
CC: Geoff Levand <geoff@infradead.org>
CC: Jens Osterkamp <Jens.Osterkamp@de.ibm.com>
CC: Ishizaki Kou <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
MAINTAINERS | 4 +-
drivers/net/Kconfig | 37 -------------
drivers/net/Makefile | 6 --
drivers/net/ethernet/Kconfig | 1 +
drivers/net/ethernet/Makefile | 1 +
drivers/net/ethernet/toshiba/Kconfig | 56 ++++++++++++++++++++
drivers/net/ethernet/toshiba/Makefile | 10 ++++
drivers/net/{ => ethernet/toshiba}/ps3_gelic_net.c | 0
drivers/net/{ => ethernet/toshiba}/ps3_gelic_net.h | 0
.../{ => ethernet/toshiba}/ps3_gelic_wireless.c | 0
.../{ => ethernet/toshiba}/ps3_gelic_wireless.h | 0
drivers/net/{ => ethernet/toshiba}/spider_net.c | 0
drivers/net/{ => ethernet/toshiba}/spider_net.h | 0
.../{ => ethernet/toshiba}/spider_net_ethtool.c | 0
drivers/net/{ => ethernet/toshiba}/tc35815.c | 0
15 files changed, 70 insertions(+), 45 deletions(-)
create mode 100644 drivers/net/ethernet/toshiba/Kconfig
create mode 100644 drivers/net/ethernet/toshiba/Makefile
rename drivers/net/{ => ethernet/toshiba}/ps3_gelic_net.c (100%)
rename drivers/net/{ => ethernet/toshiba}/ps3_gelic_net.h (100%)
rename drivers/net/{ => ethernet/toshiba}/ps3_gelic_wireless.c (100%)
rename drivers/net/{ => ethernet/toshiba}/ps3_gelic_wireless.h (100%)
rename drivers/net/{ => ethernet/toshiba}/spider_net.c (100%)
rename drivers/net/{ => ethernet/toshiba}/spider_net.h (100%)
rename drivers/net/{ => ethernet/toshiba}/spider_net_ethtool.c (100%)
rename drivers/net/{ => ethernet/toshiba}/tc35815.c (100%)
diff --git a/MAINTAINERS b/MAINTAINERS
index 77ca430..84948bd 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -5127,7 +5127,7 @@ M: Geoff Levand <geoff@infradead.org>
L: netdev@vger.kernel.org
L: cbe-oss-dev@lists.ozlabs.org
S: Maintained
-F: drivers/net/ps3_gelic_net.*
+F: drivers/net/ethernet/toshiba/ps3_gelic_net.*
PS3 PLATFORM SUPPORT
M: Geoff Levand <geoff@infradead.org>
@@ -6084,7 +6084,7 @@ M: Jens Osterkamp <jens@de.ibm.com>
L: netdev@vger.kernel.org
S: Supported
F: Documentation/networking/spider_net.txt
-F: drivers/net/spider_net*
+F: drivers/net/ethernet/toshiba/spider_net*
SPU FILE SYSTEM
M: Jeremy Kerr <jk@ozlabs.org>
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index a6edd354..1e1df3d 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -478,11 +478,6 @@ config FORCEDETH
To compile this driver as a module, choose M here. The module
will be called forcedeth.
-config TC35815
- tristate "TOSHIBA TC35815 Ethernet support"
- depends on NET_PCI && PCI && MIPS
- select PHYLIB
-
config FEALNX
tristate "Myson MTD-8xx PCI Ethernet support"
depends on NET_PCI && PCI
@@ -658,15 +653,6 @@ config SIS190
To compile this driver as a module, choose M here: the module
will be called sis190. This is recommended.
-config SPIDER_NET
- tristate "Spider Gigabit Ethernet driver"
- depends on PCI && (PPC_IBM_CELL_BLADE || PPC_CELLEB)
- select FW_LOADER
- select SUNGEM_PHY
- help
- This driver supports the Gigabit Ethernet chips present on the
- Cell Processor-Based Blades from IBM.
-
config TSI108_ETH
tristate "Tundra TSI108 gigabit Ethernet support"
depends on TSI108_BRIDGE
@@ -675,29 +661,6 @@ config TSI108_ETH
To compile this driver as a module, choose M here: the module
will be called tsi108_eth.
-config GELIC_NET
- tristate "PS3 Gigabit Ethernet driver"
- depends on PPC_PS3
- select PS3_SYS_MANAGER
- help
- This driver supports the network device on the PS3 game
- console. This driver has built-in support for Ethernet.
-
- To compile this driver as a module, choose M here: the
- module will be called ps3_gelic.
-
-config GELIC_WIRELESS
- bool "PS3 Wireless support"
- depends on WLAN
- depends on GELIC_NET
- select WIRELESS_EXT
- help
- This option adds the support for the wireless feature of PS3.
- If you have the wireless-less model of PS3 or have no plan to
- use wireless feature, disabling this option saves memory. As
- the driver automatically distinguishes the models, you can
- safely enable this option even if you have a wireless-less model.
-
config XILINX_LL_TEMAC
tristate "Xilinx LL TEMAC (LocalLink Tri-mode Ethernet MAC) driver"
depends on PPC || MICROBLAZE
diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index e448e6e..275ed4a 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -29,12 +29,6 @@ obj-$(CONFIG_SIS900) += sis900.o
obj-$(CONFIG_R6040) += r6040.o
obj-$(CONFIG_YELLOWFIN) += yellowfin.o
obj-$(CONFIG_FEALNX) += fealnx.o
-spidernet-y += spider_net.o spider_net_ethtool.o
-obj-$(CONFIG_SPIDER_NET) += spidernet.o
-obj-$(CONFIG_GELIC_NET) += ps3_gelic.o
-gelic_wireless-$(CONFIG_GELIC_WIRELESS) += ps3_gelic_wireless.o
-ps3_gelic-objs += ps3_gelic_net.o $(gelic_wireless-y)
-obj-$(CONFIG_TC35815) += tc35815.o
obj-$(CONFIG_SKFP) += skfp/
obj-$(CONFIG_ADAPTEC_STARFIRE) += starfire.o
obj-$(CONFIG_RIONET) += rionet.o
diff --git a/drivers/net/ethernet/Kconfig b/drivers/net/ethernet/Kconfig
index d90f47f3..9754247 100644
--- a/drivers/net/ethernet/Kconfig
+++ b/drivers/net/ethernet/Kconfig
@@ -48,6 +48,7 @@ source "drivers/net/ethernet/smsc/Kconfig"
source "drivers/net/ethernet/stmicro/Kconfig"
source "drivers/net/ethernet/sun/Kconfig"
source "drivers/net/ethernet/tehuti/Kconfig"
+source "drivers/net/ethernet/toshiba/Kconfig"
source "drivers/net/ethernet/via/Kconfig"
endif # ETHERNET
diff --git a/drivers/net/ethernet/Makefile b/drivers/net/ethernet/Makefile
index cf27ae0..7e7a319 100644
--- a/drivers/net/ethernet/Makefile
+++ b/drivers/net/ethernet/Makefile
@@ -39,4 +39,5 @@ obj-$(CONFIG_NET_VENDOR_SMSC) += smsc/
obj-$(CONFIG_NET_VENDOR_STMICRO) += stmicro/
obj-$(CONFIG_NET_VENDOR_SUN) += sun/
obj-$(CONFIG_NET_VENDOR_TEHUTI) += tehuti/
+obj-$(CONFIG_NET_VENDOR_TOSHIBA) += toshiba/
obj-$(CONFIG_NET_VENDOR_VIA) += via/
diff --git a/drivers/net/ethernet/toshiba/Kconfig b/drivers/net/ethernet/toshiba/Kconfig
new file mode 100644
index 0000000..6ef2ce2
--- /dev/null
+++ b/drivers/net/ethernet/toshiba/Kconfig
@@ -0,0 +1,56 @@
+#
+# Toshiba network device configuration
+#
+
+config NET_VENDOR_TOSHIBA
+ bool "Toshiba devices"
+ depends on PCI && (PPC_IBM_CELL_BLADE || PPC_CELLEB) || PPC_PS3
+ ---help---
+ If you have a network (Ethernet) card belonging to this class, say Y
+ and read the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>.
+
+ Note that the answer to this question doesn't directly affect the
+ kernel: saying N will just cause the configurator to skip all
+ the questions about Toshiba cards. If you say Y, you will be asked
+ for your specific card in the following questions.
+
+if NET_VENDOR_TOSHIBA
+
+config GELIC_NET
+ tristate "PS3 Gigabit Ethernet driver"
+ depends on PPC_PS3
+ select PS3_SYS_MANAGER
+ ---help---
+ This driver supports the network device on the PS3 game
+ console. This driver has built-in support for Ethernet.
+
+ To compile this driver as a module, choose M here: the
+ module will be called ps3_gelic.
+
+config GELIC_WIRELESS
+ bool "PS3 Wireless support"
+ depends on GELIC_NET && WLAN
+ select WIRELESS_EXT
+ ---help---
+ This option adds the support for the wireless feature of PS3.
+ If you have the wireless-less model of PS3 or have no plan to
+ use wireless feature, disabling this option saves memory. As
+ the driver automatically distinguishes the models, you can
+ safely enable this option even if you have a wireless-less model.
+
+config SPIDER_NET
+ tristate "Spider Gigabit Ethernet driver"
+ depends on PCI && (PPC_IBM_CELL_BLADE || PPC_CELLEB)
+ select FW_LOADER
+ select SUNGEM_PHY
+ ---help---
+ This driver supports the Gigabit Ethernet chips present on the
+ Cell Processor-Based Blades from IBM.
+
+config TC35815
+ tristate "TOSHIBA TC35815 Ethernet support"
+ depends on PCI && MIPS
+ select PHYLIB
+
+endif # NET_VENDOR_TOSHIBA
diff --git a/drivers/net/ethernet/toshiba/Makefile b/drivers/net/ethernet/toshiba/Makefile
new file mode 100644
index 0000000..71d861f
--- /dev/null
+++ b/drivers/net/ethernet/toshiba/Makefile
@@ -0,0 +1,10 @@
+#
+# Makefile for the Toshiba network device drivers.
+#
+
+obj-$(CONFIG_GELIC_NET) += ps3_gelic.o
+gelic_wireless-$(CONFIG_GELIC_WIRELESS) += ps3_gelic_wireless.o
+ps3_gelic-objs += ps3_gelic_net.o $(gelic_wireless-y)
+spidernet-y += spider_net.o spider_net_ethtool.o
+obj-$(CONFIG_SPIDER_NET) += spidernet.o ethernet/sun/sungem_phy.o
+obj-$(CONFIG_TC35815) += tc35815.o
diff --git a/drivers/net/ps3_gelic_net.c b/drivers/net/ethernet/toshiba/ps3_gelic_net.c
similarity index 100%
rename from drivers/net/ps3_gelic_net.c
rename to drivers/net/ethernet/toshiba/ps3_gelic_net.c
diff --git a/drivers/net/ps3_gelic_net.h b/drivers/net/ethernet/toshiba/ps3_gelic_net.h
similarity index 100%
rename from drivers/net/ps3_gelic_net.h
rename to drivers/net/ethernet/toshiba/ps3_gelic_net.h
diff --git a/drivers/net/ps3_gelic_wireless.c b/drivers/net/ethernet/toshiba/ps3_gelic_wireless.c
similarity index 100%
rename from drivers/net/ps3_gelic_wireless.c
rename to drivers/net/ethernet/toshiba/ps3_gelic_wireless.c
diff --git a/drivers/net/ps3_gelic_wireless.h b/drivers/net/ethernet/toshiba/ps3_gelic_wireless.h
similarity index 100%
rename from drivers/net/ps3_gelic_wireless.h
rename to drivers/net/ethernet/toshiba/ps3_gelic_wireless.h
diff --git a/drivers/net/spider_net.c b/drivers/net/ethernet/toshiba/spider_net.c
similarity index 100%
rename from drivers/net/spider_net.c
rename to drivers/net/ethernet/toshiba/spider_net.c
diff --git a/drivers/net/spider_net.h b/drivers/net/ethernet/toshiba/spider_net.h
similarity index 100%
rename from drivers/net/spider_net.h
rename to drivers/net/ethernet/toshiba/spider_net.h
diff --git a/drivers/net/spider_net_ethtool.c b/drivers/net/ethernet/toshiba/spider_net_ethtool.c
similarity index 100%
rename from drivers/net/spider_net_ethtool.c
rename to drivers/net/ethernet/toshiba/spider_net_ethtool.c
diff --git a/drivers/net/tc35815.c b/drivers/net/ethernet/toshiba/tc35815.c
similarity index 100%
rename from drivers/net/tc35815.c
rename to drivers/net/ethernet/toshiba/tc35815.c
--
1.7.6
^ permalink raw reply related [flat|nested] 21+ messages in thread* Re: [net-next 10/10] toshiba: Move the Toshiba drivers
2011-08-12 7:33 ` [net-next 10/10] toshiba: Move the Toshiba drivers Jeff Kirsher
@ 2011-08-12 8:22 ` Jens Osterkamp
0 siblings, 0 replies; 21+ messages in thread
From: Jens Osterkamp @ 2011-08-12 8:22 UTC (permalink / raw)
To: Jeff Kirsher
Cc: davem, Geoff Levand, gospo, Jeff Kirsher, Ishizaki Kou, netdev,
sassmann
> [net-next 10/10] toshiba: Move the Toshiba drivers
>
> Move the Toshiba ethernet drivers into drivers/net/ethernet/toshiba
> and make the necessary Kconfig and Makefile changes.
>
> CC: Geoff Levand <geoff@infradead.org>
> CC: Jens Osterkamp <Jens.Osterkamp@de.ibm.com>
> CC: Ishizaki Kou <kou.ishizaki@toshiba.co.jp>
> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff, looks good from my side, but it would be good to have Ishizakis
Signed-off-by as well.
Thanks,
Jens
Signed-off-by: Jens Osterkamp <Jens.Osterkamp@de.ibm.com>
[..]
^ permalink raw reply [flat|nested] 21+ messages in thread
* Re: [net-next 00/10] drivers/net organize Ethernet drivers (4th series)
2011-08-12 7:32 [net-next 00/10] drivers/net organize Ethernet drivers (4th series) Jeff Kirsher
` (9 preceding siblings ...)
2011-08-12 7:33 ` [net-next 10/10] toshiba: Move the Toshiba drivers Jeff Kirsher
@ 2011-08-12 8:20 ` David Miller
10 siblings, 0 replies; 21+ messages in thread
From: David Miller @ 2011-08-12 8:20 UTC (permalink / raw)
To: jeffrey.t.kirsher; +Cc: netdev, gospo, sassmann
From: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Date: Fri, 12 Aug 2011 00:32:54 -0700
> This is the fourth of seven 10 patch series to move the Ethernet
> drivers into drivers/net/ethernet/
>
> The following are changes since commit 5ff2241dd42ade03572753f9ed7743719b47c474:
> spider_net: fix compile issue introduced by driver move
> and are available in the git repository at:
> master.kernel.org:/pub/scm/linux/kernel/git/jkirsher/next-organize master
Pulled, thanks.
^ permalink raw reply [flat|nested] 21+ messages in thread