* [RESEND][PATCH 5/8][SCSI] mpt2sas : Fix for device scan following host reset could get stuck in a infinite loop
@ 2013-02-01 19:26 Sreekanth Reddy
0 siblings, 0 replies; only message in thread
From: Sreekanth Reddy @ 2013-02-01 19:26 UTC (permalink / raw)
To: jejb, sreekanth.reddy, Nagalakshmi.Nandigama, JBottomley
Cc: linux-scsi, sathya.prakash, stable
Modified device scan routine so each configuration page read breaks from the while loop
when the ioc_status is not equal to MPI2_IOCSTATUS_SUCCESS.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Cc: stable@vger.kernel.org
---
diff --git a/drivers/scsi/mpt2sas/mpt2sas_scsih.c b/drivers/scsi/mpt2sas/mpt2sas_scsih.c
index 5073586..014caef 100644
--- a/drivers/scsi/mpt2sas/mpt2sas_scsih.c
+++ b/drivers/scsi/mpt2sas/mpt2sas_scsih.c
@@ -7097,12 +7097,15 @@ _scsih_scan_for_devices_after_reset(struct MPT2SAS_ADAPTER *ioc)
struct _sas_device *sas_device;
struct _sas_node *expander_device;
static struct _raid_device *raid_device;
+ u8 retry_count;
unsigned long flags;
printk(MPT2SAS_INFO_FMT "scan devices: start\n", ioc->name);
_scsih_sas_host_refresh(ioc);
+ printk(MPT2SAS_INFO_FMT "\tscan devices: expanders start\n",
+ ioc->name);
/* expanders */
handle = 0xFFFF;
while (!(mpt2sas_config_get_expander_pg0(ioc, &mpi_reply, &expander_pg0,
@@ -7111,6 +7114,13 @@ _scsih_scan_for_devices_after_reset(struct MPT2SAS_ADAPTER *ioc)
MPI2_IOCSTATUS_MASK;
if (ioc_status == MPI2_IOCSTATUS_CONFIG_INVALID_PAGE)
break;
+ if (ioc_status != MPI2_IOCSTATUS_SUCCESS) {
+ printk(MPT2SAS_INFO_FMT "\tbreak from expander scan: " \
+ "ioc_status(0x%04x), loginfo(0x%08x)\n",
+ ioc->name, ioc_status,
+ le32_to_cpu(mpi_reply.IOCLogInfo));
+ break;
+ }
handle = le16_to_cpu(expander_pg0.DevHandle);
spin_lock_irqsave(&ioc->sas_node_lock, flags);
expander_device = mpt2sas_scsih_expander_find_by_sas_address(
@@ -7119,13 +7129,26 @@ _scsih_scan_for_devices_after_reset(struct MPT2SAS_ADAPTER *ioc)
if (expander_device)
_scsih_refresh_expander_links(ioc, expander_device,
handle);
- else
+ else {
+ printk(MPT2SAS_INFO_FMT "\tBEFORE adding expander: " \
+ "handle (0x%04x), sas_addr(0x%016llx)\n",
+ ioc->name, handle, (unsigned long long)
+ le64_to_cpu(expander_pg0.SASAddress));
_scsih_expander_add(ioc, handle);
+ printk(MPT2SAS_INFO_FMT "\tAFTER adding expander: " \
+ "handle (0x%04x), sas_addr(0x%016llx)\n",
+ ioc->name, handle, (unsigned long long)
+ le64_to_cpu(expander_pg0.SASAddress));
+ }
}
+ printk(MPT2SAS_INFO_FMT "\tscan devices: expanders complete\n",
+ ioc->name);
+
if (!ioc->ir_firmware)
goto skip_to_sas;
+ printk(MPT2SAS_INFO_FMT "\tscan devices phys disk start\n", ioc->name);
/* phys disk */
phys_disk_num = 0xFF;
while (!(mpt2sas_config_get_phys_disk_pg0(ioc, &mpi_reply,
@@ -7135,6 +7158,13 @@ _scsih_scan_for_devices_after_reset(struct MPT2SAS_ADAPTER *ioc)
MPI2_IOCSTATUS_MASK;
if (ioc_status == MPI2_IOCSTATUS_CONFIG_INVALID_PAGE)
break;
+ if (ioc_status != MPI2_IOCSTATUS_SUCCESS) {
+ printk(MPT2SAS_INFO_FMT "\tbreak from phys disk scan:" \
+ "ioc_status(0x%04x), loginfo(0x%08x)\n",
+ ioc->name, ioc_status,
+ le32_to_cpu(mpi_reply.IOCLogInfo));
+ break;
+ }
phys_disk_num = pd_pg0.PhysDiskNum;
handle = le16_to_cpu(pd_pg0.DevHandle);
spin_lock_irqsave(&ioc->sas_device_lock, flags);
@@ -7146,17 +7176,46 @@ _scsih_scan_for_devices_after_reset(struct MPT2SAS_ADAPTER *ioc)
&sas_device_pg0, MPI2_SAS_DEVICE_PGAD_FORM_HANDLE,
handle) != 0)
continue;
+ ioc_status = le16_to_cpu(mpi_reply.IOCStatus) &
+ MPI2_IOCSTATUS_MASK;
+ if (ioc_status != MPI2_IOCSTATUS_SUCCESS) {
+ printk(MPT2SAS_INFO_FMT "\tbreak from phys disk scan " \
+ "ioc_status(0x%04x), loginfo(0x%08x)\n",
+ ioc->name, ioc_status,
+ le32_to_cpu(mpi_reply.IOCLogInfo));
+ break;
+ }
parent_handle = le16_to_cpu(sas_device_pg0.ParentDevHandle);
if (!_scsih_get_sas_address(ioc, parent_handle,
&sas_address)) {
+ printk(MPT2SAS_INFO_FMT "\tBEFORE adding phys disk: " \
+ " handle (0x%04x), sas_addr(0x%016llx)\n",
+ ioc->name, handle, (unsigned long long)
+ le64_to_cpu(sas_device_pg0.SASAddress));
mpt2sas_transport_update_links(ioc, sas_address,
handle, sas_device_pg0.PhyNum,
MPI2_SAS_NEG_LINK_RATE_1_5);
set_bit(handle, ioc->pd_handles);
- _scsih_add_device(ioc, handle, 0, 1);
+ retry_count = 0;
+ /* This will retry adding the end device.
+ * _scsih_add_device() will decide on retries and
+ * return "1" when it should be retried
+ */
+ while (_scsih_add_device(ioc, handle, retry_count++,
+ 1)) {
+ ssleep(1);
+ }
+ printk(MPT2SAS_INFO_FMT "\tAFTER adding phys disk: " \
+ " handle (0x%04x), sas_addr(0x%016llx)\n",
+ ioc->name, handle, (unsigned long long)
+ le64_to_cpu(sas_device_pg0.SASAddress));
}
}
+ printk(MPT2SAS_INFO_FMT "\tscan devices: phys disk complete\n",
+ ioc->name);
+
+ printk(MPT2SAS_INFO_FMT "\tscan devices: volumes start\n", ioc->name);
/* volumes */
handle = 0xFFFF;
while (!(mpt2sas_config_get_raid_volume_pg1(ioc, &mpi_reply,
@@ -7165,6 +7225,13 @@ _scsih_scan_for_devices_after_reset(struct MPT2SAS_ADAPTER *ioc)
MPI2_IOCSTATUS_MASK;
if (ioc_status == MPI2_IOCSTATUS_CONFIG_INVALID_PAGE)
break;
+ if (ioc_status != MPI2_IOCSTATUS_SUCCESS) {
+ printk(MPT2SAS_INFO_FMT "\tbreak from volume scan: " \
+ "ioc_status(0x%04x), loginfo(0x%08x)\n",
+ ioc->name, ioc_status,
+ le32_to_cpu(mpi_reply.IOCLogInfo));
+ break;
+ }
handle = le16_to_cpu(volume_pg1.DevHandle);
spin_lock_irqsave(&ioc->raid_device_lock, flags);
raid_device = _scsih_raid_device_find_by_wwid(ioc,
@@ -7176,18 +7243,38 @@ _scsih_scan_for_devices_after_reset(struct MPT2SAS_ADAPTER *ioc)
&volume_pg0, MPI2_RAID_VOLUME_PGAD_FORM_HANDLE, handle,
sizeof(Mpi2RaidVolPage0_t)))
continue;
+ ioc_status = le16_to_cpu(mpi_reply.IOCStatus) &
+ MPI2_IOCSTATUS_MASK;
+ if (ioc_status != MPI2_IOCSTATUS_SUCCESS) {
+ printk(MPT2SAS_INFO_FMT "\tbreak from volume scan: " \
+ "ioc_status(0x%04x), loginfo(0x%08x)\n",
+ ioc->name, ioc_status,
+ le32_to_cpu(mpi_reply.IOCLogInfo));
+ break;
+ }
if (volume_pg0.VolumeState == MPI2_RAID_VOL_STATE_OPTIMAL ||
volume_pg0.VolumeState == MPI2_RAID_VOL_STATE_ONLINE ||
volume_pg0.VolumeState == MPI2_RAID_VOL_STATE_DEGRADED) {
memset(&element, 0, sizeof(Mpi2EventIrConfigElement_t));
element.ReasonCode = MPI2_EVENT_IR_CHANGE_RC_ADDED;
element.VolDevHandle = volume_pg1.DevHandle;
+ printk(MPT2SAS_INFO_FMT "\tBEFORE adding volume: " \
+ " handle (0x%04x)\n", ioc->name,
+ volume_pg1.DevHandle);
_scsih_sas_volume_add(ioc, &element);
+ printk(MPT2SAS_INFO_FMT "\tAFTER adding volume: " \
+ " handle (0x%04x)\n", ioc->name,
+ volume_pg1.DevHandle);
}
}
+ printk(MPT2SAS_INFO_FMT "\tscan devices: volumes complete\n",
+ ioc->name);
+
skip_to_sas:
+ printk(MPT2SAS_INFO_FMT "\tscan devices: end devices start\n",
+ ioc->name);
/* sas devices */
handle = 0xFFFF;
while (!(mpt2sas_config_get_sas_device_pg0(ioc, &mpi_reply,
@@ -7197,6 +7285,13 @@ _scsih_scan_for_devices_after_reset(struct MPT2SAS_ADAPTER *ioc)
MPI2_IOCSTATUS_MASK;
if (ioc_status == MPI2_IOCSTATUS_CONFIG_INVALID_PAGE)
break;
+ if (ioc_status != MPI2_IOCSTATUS_SUCCESS) {
+ printk(MPT2SAS_INFO_FMT "\tbreak from end device scan:"\
+ " ioc_status(0x%04x), loginfo(0x%08x)\n",
+ ioc->name, ioc_status,
+ le32_to_cpu(mpi_reply.IOCLogInfo));
+ break;
+ }
handle = le16_to_cpu(sas_device_pg0.DevHandle);
if (!(_scsih_is_end_device(
le32_to_cpu(sas_device_pg0.DeviceInfo))))
@@ -7209,12 +7304,31 @@ _scsih_scan_for_devices_after_reset(struct MPT2SAS_ADAPTER *ioc)
continue;
parent_handle = le16_to_cpu(sas_device_pg0.ParentDevHandle);
if (!_scsih_get_sas_address(ioc, parent_handle, &sas_address)) {
+ printk(MPT2SAS_INFO_FMT "\tBEFORE adding end device: " \
+ "handle (0x%04x), sas_addr(0x%016llx)\n",
+ ioc->name, handle, (unsigned long long)
+ le64_to_cpu(sas_device_pg0.SASAddress));
mpt2sas_transport_update_links(ioc, sas_address, handle,
sas_device_pg0.PhyNum, MPI2_SAS_NEG_LINK_RATE_1_5);
- _scsih_add_device(ioc, handle, 0, 0);
+ retry_count = 0;
+ /* This will retry adding the end device.
+ * _scsih_add_device() will decide on retries and
+ * return "1" when it should be retried
+ */
+ while (_scsih_add_device(ioc, handle, retry_count++,
+ 0)) {
+ ssleep(1);
+ }
+ printk(MPT2SAS_INFO_FMT "\tAFTER adding end device: " \
+ "handle (0x%04x), sas_addr(0x%016llx)\n",
+ ioc->name, handle, (unsigned long long)
+ le64_to_cpu(sas_device_pg0.SASAddress));
}
}
+ printk(MPT2SAS_INFO_FMT "\tscan devices: end devices complete\n",
+ ioc->name);
+
printk(MPT2SAS_INFO_FMT "scan devices: complete\n", ioc->name);
}
^ permalink raw reply related [flat|nested] only message in thread
only message in thread, other threads:[~2013-02-01 19:26 UTC | newest]
Thread overview: (only message) (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2013-02-01 19:26 [RESEND][PATCH 5/8][SCSI] mpt2sas : Fix for device scan following host reset could get stuck in a infinite loop Sreekanth Reddy
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.