Re: [PATCH] xen/pci: Deal with toolstack missing an 'XenbusStateClosing'.

[Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>]

On Wed, Jun 12, 2013 at 02:47:11PM +0100, George Dunlap wrote:
> On 12/06/13 14:45, Konrad Rzeszutek Wilk wrote:
> >On Tue, Jun 11, 2013 at 05:17:45PM +0100, George Dunlap wrote:
> >>On 06/11/2013 05:08 PM, konrad wilk wrote:
> >>>On 6/11/2013 11:36 AM, George Dunlap wrote:
> >>>>On 06/10/2013 10:06 PM, Konrad Rzeszutek Wilk wrote:
> >>>>>There are two tool-stack that can instruct the Xen PCI frontend
> >>>>>and backend to change states: 'xm' (Python code with a daemon),
> >>>>>and 'xl' (C library - does not keep state changes).
> >>>>>
> >>>>>With the 'xm', the path to disconnect a PCI device (xm pci-detach
> >>>>><guest> <BDF>)is:
> >>>>>
> >>>>>4(Connected)->7(Reconfiguring*)-> 8(Reconfigured)->
> >>>>>4(Connected)->5(Closing*).
> >>>>>
> >>>>>The * is for states that the tool-stack sets. For 'xl', it is similar:
> >>>>>
> >>>>>4(Connected)->7(Reconfiguring*)-> 8(Reconfigured)-> 4(Connected)
> >>>>>
> >>>>>Both of them also tear down the XenBus structure, so the backend
> >>>>>state ends up going in the 3(Initialised) and calls
> >>>>>pcifront_xenbus_remove.
> >>>>So I looked a little bit into this; there are actually two different
> >>>>states that happen as part of this handshake.  In order to disonnect a
> >>>>*device*, xl signals using the *bus* state, like this:
> >>>>* Wait for the *bus* to be in state 4(Connected)
> >>>>* Set the *device* state to 5(Closing)
> >>>>* Set the *bus* state to 7(Reconfiguring)
> >>>>* Wait for the *bus* state to return to 4(Connected)
> >>>>
> >>>>So are all of these states you see the *bus* state?  And why would you
> >>>>disconnect the whole pci bus if you're only removing one device?
> >>>Correct. The stats I enumerated are *bus* states. Not per-device states.
> >>>I presume (and I hadn't checked xm) that Xend has some logic to only
> >>>disconnect the bus if all of the PCI devices have been disconnected. In
> >>>'xl' it does not do that.
> >>>
> >>>The testing I did was just with one PCI device.
> >>Ah, OK -- I see now.  The problem is that the code in the Linux side
> >>didn't know about the whole "4->7->8->4" thing to unplug a device.
> >>In all likelihood, if you had used xm with two devices (so that the
> >>bus didn't get disconnected), then you would have run across the
> >>same error.
> >>
> >>So at least part of the problem *is* a bug in Linux.
> >Good! Bjorn, would you be OK Ack-ing the patch I sent (attached here
> >for reference) or putting it in your queue for Linus?
> >
> >My plan would be to send it to Linus in the 3.11 merge window.
> 
> One nit -- "to work with the 'xl' toolstack" -- didn't we theorize
> this would also be broken with xm if you had two devices passed
> through?

Yes. I will fix up the title to reflect that shortly (say Friday?)

Thanks for your sharp eyes.