[PATCH] of: irq: Pass trigger type in IRQ resource flags

[PATCH] of: irq: Pass trigger type in IRQ resource flags

[Tomasz Figa]

Some drivers might rely on availability of trigger flags in IRQ
resource, for example to configure the hardware for particular interrupt
type. However current code creating IRQ resources from data in device
tree does not configure trigger flags in resulting resources.

This patch solves the problem, based on the fact that
irq_of_parse_and_map() configures the trigger based on DT interrupt
specifier, IRQD_TRIGGER_* flags are consistent with IORESOURCE_IRQ_*,
and we can get trigger type by calling irqd_get_trigger_type() after
mapping the interrupt.

Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
---
 drivers/of/irq.c | 10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/drivers/of/irq.c b/drivers/of/irq.c
index a3c1c5a..79a7a26 100644
--- a/drivers/of/irq.c
+++ b/drivers/of/irq.c
@@ -355,6 +355,16 @@ int of_irq_to_resource(struct device_node *dev, int index, struct resource *r)
 		r->start = r->end = irq;
 		r->flags = IORESOURCE_IRQ;
 		r->name = name ? name : dev->full_name;
+
+		/*
+		 * Some drivers might rely on availability of trigger flags
+		 * in IRQ resource. Since irq_of_parse_and_map() configures the
+		 * trigger based on interrupt specifier and IRQD_TRIGGER_*
+		 * flags are consistent with IORESOURCE_IRQ_*, we can get
+		 * trigger type that was just set and pass it through resource
+		 * flags as well.
+		 */
+		r->flags |= irqd_get_trigger_type(irq_get_irq_data(irq));
 	}
 
 	return irq;
-- 
1.8.2.1

[PATCH] of: irq: Pass trigger type in IRQ resource flags

[Tomasz Figa]

Some drivers might rely on availability of trigger flags in IRQ
resource, for example to configure the hardware for particular interrupt
type. However current code creating IRQ resources from data in device
tree does not configure trigger flags in resulting resources.

This patch solves the problem, based on the fact that
irq_of_parse_and_map() configures the trigger based on DT interrupt
specifier, IRQD_TRIGGER_* flags are consistent with IORESOURCE_IRQ_*,
and we can get trigger type by calling irqd_get_trigger_type() after
mapping the interrupt.

Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
---
 drivers/of/irq.c | 10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/drivers/of/irq.c b/drivers/of/irq.c
index a3c1c5a..79a7a26 100644
--- a/drivers/of/irq.c
+++ b/drivers/of/irq.c
@@ -355,6 +355,16 @@ int of_irq_to_resource(struct device_node *dev, int index, struct resource *r)
 		r->start = r->end = irq;
 		r->flags = IORESOURCE_IRQ;
 		r->name = name ? name : dev->full_name;
+
+		/*
+		 * Some drivers might rely on availability of trigger flags
+		 * in IRQ resource. Since irq_of_parse_and_map() configures the
+		 * trigger based on interrupt specifier and IRQD_TRIGGER_*
+		 * flags are consistent with IORESOURCE_IRQ_*, we can get
+		 * trigger type that was just set and pass it through resource
+		 * flags as well.
+		 */
+		r->flags |= irqd_get_trigger_type(irq_get_irq_data(irq));
 	}
 
 	return irq;
-- 
1.8.2.1

[PATCH] of: irq: Pass trigger type in IRQ resource flags

[Tomasz Figa]

Some drivers might rely on availability of trigger flags in IRQ
resource, for example to configure the hardware for particular interrupt
type. However current code creating IRQ resources from data in device
tree does not configure trigger flags in resulting resources.

This patch solves the problem, based on the fact that
irq_of_parse_and_map() configures the trigger based on DT interrupt
specifier, IRQD_TRIGGER_* flags are consistent with IORESOURCE_IRQ_*,
and we can get trigger type by calling irqd_get_trigger_type() after
mapping the interrupt.

Signed-off-by: Tomasz Figa <tomasz.figa-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
---
 drivers/of/irq.c | 10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/drivers/of/irq.c b/drivers/of/irq.c
index a3c1c5a..79a7a26 100644
--- a/drivers/of/irq.c
+++ b/drivers/of/irq.c
@@ -355,6 +355,16 @@ int of_irq_to_resource(struct device_node *dev, int index, struct resource *r)
 		r->start = r->end = irq;
 		r->flags = IORESOURCE_IRQ;
 		r->name = name ? name : dev->full_name;
+
+		/*
+		 * Some drivers might rely on availability of trigger flags
+		 * in IRQ resource. Since irq_of_parse_and_map() configures the
+		 * trigger based on interrupt specifier and IRQD_TRIGGER_*
+		 * flags are consistent with IORESOURCE_IRQ_*, we can get
+		 * trigger type that was just set and pass it through resource
+		 * flags as well.
+		 */
+		r->flags |= irqd_get_trigger_type(irq_get_irq_data(irq));
 	}
 
 	return irq;
-- 
1.8.2.1

[PATCH] of: irq: Pass trigger type in IRQ resource flags

[Tomasz Figa]

Hi,

On Sunday 19 of May 2013 00:56:30 Tomasz Figa wrote:
> Some drivers might rely on availability of trigger flags in IRQ
> resource, for example to configure the hardware for particular interrupt
> type. However current code creating IRQ resources from data in device
> tree does not configure trigger flags in resulting resources.
> 
> This patch solves the problem, based on the fact that
> irq_of_parse_and_map() configures the trigger based on DT interrupt
> specifier, IRQD_TRIGGER_* flags are consistent with IORESOURCE_IRQ_*,
> and we can get trigger type by calling irqd_get_trigger_type() after
> mapping the interrupt.
> 
> Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
> ---
>  drivers/of/irq.c | 10 ++++++++++
>  1 file changed, 10 insertions(+)
> 
> diff --git a/drivers/of/irq.c b/drivers/of/irq.c
> index a3c1c5a..79a7a26 100644
> --- a/drivers/of/irq.c
> +++ b/drivers/of/irq.c
> @@ -355,6 +355,16 @@ int of_irq_to_resource(struct device_node *dev, int
> index, struct resource *r) r->start = r->end = irq;
>  		r->flags = IORESOURCE_IRQ;
>  		r->name = name ? name : dev->full_name;
> +
> +		/*
> +		 * Some drivers might rely on availability of trigger 
flags
> +		 * in IRQ resource. Since irq_of_parse_and_map() 
configures the
> +		 * trigger based on interrupt specifier and IRQD_TRIGGER_*
> +		 * flags are consistent with IORESOURCE_IRQ_*, we can get
> +		 * trigger type that was just set and pass it through 
resource
> +		 * flags as well.
> +		 */
> +		r->flags |= irqd_get_trigger_type(irq_get_irq_data(irq));
>  	}
> 
>  	return irq;

Any comments on this patch?

Best regards,
Tomasz

Re: [PATCH] of: irq: Pass trigger type in IRQ resource flags

[Tomasz Figa]

Hi,

On Sunday 19 of May 2013 00:56:30 Tomasz Figa wrote:
> Some drivers might rely on availability of trigger flags in IRQ
> resource, for example to configure the hardware for particular interrupt
> type. However current code creating IRQ resources from data in device
> tree does not configure trigger flags in resulting resources.
> 
> This patch solves the problem, based on the fact that
> irq_of_parse_and_map() configures the trigger based on DT interrupt
> specifier, IRQD_TRIGGER_* flags are consistent with IORESOURCE_IRQ_*,
> and we can get trigger type by calling irqd_get_trigger_type() after
> mapping the interrupt.
> 
> Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
> ---
>  drivers/of/irq.c | 10 ++++++++++
>  1 file changed, 10 insertions(+)
> 
> diff --git a/drivers/of/irq.c b/drivers/of/irq.c
> index a3c1c5a..79a7a26 100644
> --- a/drivers/of/irq.c
> +++ b/drivers/of/irq.c
> @@ -355,6 +355,16 @@ int of_irq_to_resource(struct device_node *dev, int
> index, struct resource *r) r->start = r->end = irq;
>  		r->flags = IORESOURCE_IRQ;
>  		r->name = name ? name : dev->full_name;
> +
> +		/*
> +		 * Some drivers might rely on availability of trigger 
flags
> +		 * in IRQ resource. Since irq_of_parse_and_map() 
configures the
> +		 * trigger based on interrupt specifier and IRQD_TRIGGER_*
> +		 * flags are consistent with IORESOURCE_IRQ_*, we can get
> +		 * trigger type that was just set and pass it through 
resource
> +		 * flags as well.
> +		 */
> +		r->flags |= irqd_get_trigger_type(irq_get_irq_data(irq));
>  	}
> 
>  	return irq;

Any comments on this patch?

Best regards,
Tomasz

Re: [PATCH] of: irq: Pass trigger type in IRQ resource flags

[Tomasz Figa]

Hi,

On Sunday 19 of May 2013 00:56:30 Tomasz Figa wrote:
> Some drivers might rely on availability of trigger flags in IRQ
> resource, for example to configure the hardware for particular interrupt
> type. However current code creating IRQ resources from data in device
> tree does not configure trigger flags in resulting resources.
> 
> This patch solves the problem, based on the fact that
> irq_of_parse_and_map() configures the trigger based on DT interrupt
> specifier, IRQD_TRIGGER_* flags are consistent with IORESOURCE_IRQ_*,
> and we can get trigger type by calling irqd_get_trigger_type() after
> mapping the interrupt.
> 
> Signed-off-by: Tomasz Figa <tomasz.figa-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
> ---
>  drivers/of/irq.c | 10 ++++++++++
>  1 file changed, 10 insertions(+)
> 
> diff --git a/drivers/of/irq.c b/drivers/of/irq.c
> index a3c1c5a..79a7a26 100644
> --- a/drivers/of/irq.c
> +++ b/drivers/of/irq.c
> @@ -355,6 +355,16 @@ int of_irq_to_resource(struct device_node *dev, int
> index, struct resource *r) r->start = r->end = irq;
>  		r->flags = IORESOURCE_IRQ;
>  		r->name = name ? name : dev->full_name;
> +
> +		/*
> +		 * Some drivers might rely on availability of trigger 
flags
> +		 * in IRQ resource. Since irq_of_parse_and_map() 
configures the
> +		 * trigger based on interrupt specifier and IRQD_TRIGGER_*
> +		 * flags are consistent with IORESOURCE_IRQ_*, we can get
> +		 * trigger type that was just set and pass it through 
resource
> +		 * flags as well.
> +		 */
> +		r->flags |= irqd_get_trigger_type(irq_get_irq_data(irq));
>  	}
> 
>  	return irq;

Any comments on this patch?

Best regards,
Tomasz

[PATCH] of: irq: Pass trigger type in IRQ resource flags

[Grant Likely]

On Wed, 05 Jun 2013 20:20:39 +0200, Tomasz Figa <tomasz.figa@gmail.com> wrote:
> Hi,
> 
> On Sunday 19 of May 2013 00:56:30 Tomasz Figa wrote:
> > Some drivers might rely on availability of trigger flags in IRQ
> > resource, for example to configure the hardware for particular interrupt
> > type. However current code creating IRQ resources from data in device
> > tree does not configure trigger flags in resulting resources.
> > 
> > This patch solves the problem, based on the fact that
> > irq_of_parse_and_map() configures the trigger based on DT interrupt
> > specifier, IRQD_TRIGGER_* flags are consistent with IORESOURCE_IRQ_*,
> > and we can get trigger type by calling irqd_get_trigger_type() after
> > mapping the interrupt.
> > 
> > Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
> > ---
> >  drivers/of/irq.c | 10 ++++++++++
> >  1 file changed, 10 insertions(+)
> > 
> > diff --git a/drivers/of/irq.c b/drivers/of/irq.c
> > index a3c1c5a..79a7a26 100644
> > --- a/drivers/of/irq.c
> > +++ b/drivers/of/irq.c
> > @@ -355,6 +355,16 @@ int of_irq_to_resource(struct device_node *dev, int
> > index, struct resource *r) r->start = r->end = irq;
> >  		r->flags = IORESOURCE_IRQ;
> >  		r->name = name ? name : dev->full_name;
> > +
> > +		/*
> > +		 * Some drivers might rely on availability of trigger 
> flags
> > +		 * in IRQ resource. Since irq_of_parse_and_map() 
> configures the
> > +		 * trigger based on interrupt specifier and IRQD_TRIGGER_*
> > +		 * flags are consistent with IORESOURCE_IRQ_*, we can get
> > +		 * trigger type that was just set and pass it through 
> resource
> > +		 * flags as well.
> > +		 */
> > +		r->flags |= irqd_get_trigger_type(irq_get_irq_data(irq));
> >  	}
> > 
> >  	return irq;
> 
> Any comments on this patch?

That's actually a pretty good solution and a whole lot less invasive
that the approach that Javier was pursuing. Javier, I'm going to pick
up this patch. Please yell if it doesn't solve the problem that you're
trying to solve.

g.

Re: [PATCH] of: irq: Pass trigger type in IRQ resource flags

[Grant Likely]

On Wed, 05 Jun 2013 20:20:39 +0200, Tomasz Figa <tomasz.figa@gmail.com> wrote:
> Hi,
> 
> On Sunday 19 of May 2013 00:56:30 Tomasz Figa wrote:
> > Some drivers might rely on availability of trigger flags in IRQ
> > resource, for example to configure the hardware for particular interrupt
> > type. However current code creating IRQ resources from data in device
> > tree does not configure trigger flags in resulting resources.
> > 
> > This patch solves the problem, based on the fact that
> > irq_of_parse_and_map() configures the trigger based on DT interrupt
> > specifier, IRQD_TRIGGER_* flags are consistent with IORESOURCE_IRQ_*,
> > and we can get trigger type by calling irqd_get_trigger_type() after
> > mapping the interrupt.
> > 
> > Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
> > ---
> >  drivers/of/irq.c | 10 ++++++++++
> >  1 file changed, 10 insertions(+)
> > 
> > diff --git a/drivers/of/irq.c b/drivers/of/irq.c
> > index a3c1c5a..79a7a26 100644
> > --- a/drivers/of/irq.c
> > +++ b/drivers/of/irq.c
> > @@ -355,6 +355,16 @@ int of_irq_to_resource(struct device_node *dev, int
> > index, struct resource *r) r->start = r->end = irq;
> >  		r->flags = IORESOURCE_IRQ;
> >  		r->name = name ? name : dev->full_name;
> > +
> > +		/*
> > +		 * Some drivers might rely on availability of trigger 
> flags
> > +		 * in IRQ resource. Since irq_of_parse_and_map() 
> configures the
> > +		 * trigger based on interrupt specifier and IRQD_TRIGGER_*
> > +		 * flags are consistent with IORESOURCE_IRQ_*, we can get
> > +		 * trigger type that was just set and pass it through 
> resource
> > +		 * flags as well.
> > +		 */
> > +		r->flags |= irqd_get_trigger_type(irq_get_irq_data(irq));
> >  	}
> > 
> >  	return irq;
> 
> Any comments on this patch?

That's actually a pretty good solution and a whole lot less invasive
that the approach that Javier was pursuing. Javier, I'm going to pick
up this patch. Please yell if it doesn't solve the problem that you're
trying to solve.

g.

[PATCH] of: irq: Pass trigger type in IRQ resource flags

[Javier Martinez Canillas]

On 15/06/2013, at 00:00, Grant Likely <grant.likely@linaro.org> wrote:

> On Wed, 05 Jun 2013 20:20:39 +0200, Tomasz Figa <tomasz.figa@gmail.com> wrote:
>> Hi,
>> 
>> On Sunday 19 of May 2013 00:56:30 Tomasz Figa wrote:
>>> Some drivers might rely on availability of trigger flags in IRQ
>>> resource, for example to configure the hardware for particular interrupt
>>> type. However current code creating IRQ resources from data in device
>>> tree does not configure trigger flags in resulting resources.
>>> 
>>> This patch solves the problem, based on the fact that
>>> irq_of_parse_and_map() configures the trigger based on DT interrupt
>>> specifier, IRQD_TRIGGER_* flags are consistent with IORESOURCE_IRQ_*,
>>> and we can get trigger type by calling irqd_get_trigger_type() after
>>> mapping the interrupt.
>>> 
>>> Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
>>> ---
>>> drivers/of/irq.c | 10 ++++++++++
>>> 1 file changed, 10 insertions(+)
>>> 
>>> diff --git a/drivers/of/irq.c b/drivers/of/irq.c
>>> index a3c1c5a..79a7a26 100644
>>> --- a/drivers/of/irq.c
>>> +++ b/drivers/of/irq.c
>>> @@ -355,6 +355,16 @@ int of_irq_to_resource(struct device_node *dev, int
>>> index, struct resource *r) r->start = r->end = irq;
>>>        r->flags = IORESOURCE_IRQ;
>>>        r->name = name ? name : dev->full_name;
>>> +
>>> +        /*
>>> +         * Some drivers might rely on availability of trigger
>> flags
>>> +         * in IRQ resource. Since irq_of_parse_and_map()
>> configures the
>>> +         * trigger based on interrupt specifier and IRQD_TRIGGER_*
>>> +         * flags are consistent with IORESOURCE_IRQ_*, we can get
>>> +         * trigger type that was just set and pass it through
>> resource
>>> +         * flags as well.
>>> +         */
>>> +        r->flags |= irqd_get_trigger_type(irq_get_irq_data(irq));
>>>    }
>>> 
>>>    return irq;
>> 
>> Any comments on this patch?
> 
> That's actually a pretty good solution and a whole lot less invasive
> that the approach that Javier was pursuing. Javier, I'm going to pick
> up this patch. Please yell if it doesn't solve the problem that you're
> trying to solve.
> 
> g.
> 

It solves the issue I was trying to solve and the solution is indeed more elegant and simpler than the one I posted.

Thanks a lot for pointing this out.

Best regards,
Javier

Re: [PATCH] of: irq: Pass trigger type in IRQ resource flags

[Javier Martinez Canillas]

On 15/06/2013, at 00:00, Grant Likely <grant.likely@linaro.org> wrote:

> On Wed, 05 Jun 2013 20:20:39 +0200, Tomasz Figa <tomasz.figa@gmail.com> wrote:
>> Hi,
>> 
>> On Sunday 19 of May 2013 00:56:30 Tomasz Figa wrote:
>>> Some drivers might rely on availability of trigger flags in IRQ
>>> resource, for example to configure the hardware for particular interrupt
>>> type. However current code creating IRQ resources from data in device
>>> tree does not configure trigger flags in resulting resources.
>>> 
>>> This patch solves the problem, based on the fact that
>>> irq_of_parse_and_map() configures the trigger based on DT interrupt
>>> specifier, IRQD_TRIGGER_* flags are consistent with IORESOURCE_IRQ_*,
>>> and we can get trigger type by calling irqd_get_trigger_type() after
>>> mapping the interrupt.
>>> 
>>> Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
>>> ---
>>> drivers/of/irq.c | 10 ++++++++++
>>> 1 file changed, 10 insertions(+)
>>> 
>>> diff --git a/drivers/of/irq.c b/drivers/of/irq.c
>>> index a3c1c5a..79a7a26 100644
>>> --- a/drivers/of/irq.c
>>> +++ b/drivers/of/irq.c
>>> @@ -355,6 +355,16 @@ int of_irq_to_resource(struct device_node *dev, int
>>> index, struct resource *r) r->start = r->end = irq;
>>>        r->flags = IORESOURCE_IRQ;
>>>        r->name = name ? name : dev->full_name;
>>> +
>>> +        /*
>>> +         * Some drivers might rely on availability of trigger
>> flags
>>> +         * in IRQ resource. Since irq_of_parse_and_map()
>> configures the
>>> +         * trigger based on interrupt specifier and IRQD_TRIGGER_*
>>> +         * flags are consistent with IORESOURCE_IRQ_*, we can get
>>> +         * trigger type that was just set and pass it through
>> resource
>>> +         * flags as well.
>>> +         */
>>> +        r->flags |= irqd_get_trigger_type(irq_get_irq_data(irq));
>>>    }
>>> 
>>>    return irq;
>> 
>> Any comments on this patch?
> 
> That's actually a pretty good solution and a whole lot less invasive
> that the approach that Javier was pursuing. Javier, I'm going to pick
> up this patch. Please yell if it doesn't solve the problem that you're
> trying to solve.
> 
> g.
> 

It solves the issue I was trying to solve and the solution is indeed more elegant and simpler than the one I posted.

Thanks a lot for pointing this out.

Best regards,
Javier

[PATCH] of: irq: Pass trigger type in IRQ resource flags

[Tomasz Figa]

Some drivers might rely on availability of trigger flags in IRQ
resource, for example to configure the hardware for particular interrupt
type. However current code creating IRQ resources from data in device
tree does not configure trigger flags in resulting resources.

This patch tries to solve the problem, based on the fact that
irq_of_parse_and_map() configures the trigger based on DT interrupt
specifier and IRQD_TRIGGER_* flags are consistent with IORESOURCE_IRQ_*,
and we can get correct trigger flags by calling irqd_get_trigger_type()
after mapping the interrupt.

Signed-off-by: Tomasz Figa <tomasz.figa-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
---
 drivers/of/irq.c | 10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/drivers/of/irq.c b/drivers/of/irq.c
index 1752988..12742d0 100644
--- a/drivers/of/irq.c
+++ b/drivers/of/irq.c
@@ -356,6 +356,16 @@ int of_irq_to_resource(struct device_node *dev, int index, struct resource *r)
 		r->start = r->end = irq;
 		r->flags = IORESOURCE_IRQ;
 		r->name = name ? name : dev->full_name;
+
+		/*
+		 * Some drivers might rely on availability of trigger flags
+		 * in IRQ resource. Since irq_of_parse_and_map() configures the
+		 * trigger based on interrupt specifier and IRQD_TRIGGER_*
+		 * flags are consistent with IORESOURCE_IRQ_*, we can get
+		 * trigger type that was just set and pass it through resource
+		 * flags as well.
+		 */
+		r->flags |= irqd_get_trigger_type(irq_get_irq_data(irq));
 	}
 
 	return irq;
-- 
1.8.3.2

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH] of: irq: Pass trigger type in IRQ resource flags

[Tomasz Figa]

Some drivers might rely on availability of trigger flags in IRQ
resource, for example to configure the hardware for particular interrupt
type. However current code creating IRQ resources from data in device
tree does not configure trigger flags in resulting resources.

This patch tries to solve the problem, based on the fact that
irq_of_parse_and_map() configures the trigger based on DT interrupt
specifier and IRQD_TRIGGER_* flags are consistent with IORESOURCE_IRQ_*,
and we can get correct trigger flags by calling irqd_get_trigger_type()
after mapping the interrupt.

Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
---
 drivers/of/irq.c | 10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/drivers/of/irq.c b/drivers/of/irq.c
index 1752988..12742d0 100644
--- a/drivers/of/irq.c
+++ b/drivers/of/irq.c
@@ -356,6 +356,16 @@ int of_irq_to_resource(struct device_node *dev, int index, struct resource *r)
 		r->start = r->end = irq;
 		r->flags = IORESOURCE_IRQ;
 		r->name = name ? name : dev->full_name;
+
+		/*
+		 * Some drivers might rely on availability of trigger flags
+		 * in IRQ resource. Since irq_of_parse_and_map() configures the
+		 * trigger based on interrupt specifier and IRQD_TRIGGER_*
+		 * flags are consistent with IORESOURCE_IRQ_*, we can get
+		 * trigger type that was just set and pass it through resource
+		 * flags as well.
+		 */
+		r->flags |= irqd_get_trigger_type(irq_get_irq_data(irq));
 	}
 
 	return irq;
-- 
1.8.3.2

Re: [PATCH] of: irq: Pass trigger type in IRQ resource flags

[Grant Likely]

On Sat, 28 Sep 2013 19:52:51 +0200, Tomasz Figa <tomasz.figa@gmail.com> wrote:
> Some drivers might rely on availability of trigger flags in IRQ
> resource, for example to configure the hardware for particular interrupt
> type. However current code creating IRQ resources from data in device
> tree does not configure trigger flags in resulting resources.
> 
> This patch tries to solve the problem, based on the fact that
> irq_of_parse_and_map() configures the trigger based on DT interrupt
> specifier and IRQD_TRIGGER_* flags are consistent with IORESOURCE_IRQ_*,
> and we can get correct trigger flags by calling irqd_get_trigger_type()
> after mapping the interrupt.
> 
> Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>

Applied, thanks.

g.

> ---
>  drivers/of/irq.c | 10 ++++++++++
>  1 file changed, 10 insertions(+)
> 
> diff --git a/drivers/of/irq.c b/drivers/of/irq.c
> index 1752988..12742d0 100644
> --- a/drivers/of/irq.c
> +++ b/drivers/of/irq.c
> @@ -356,6 +356,16 @@ int of_irq_to_resource(struct device_node *dev, int index, struct resource *r)
>  		r->start = r->end = irq;
>  		r->flags = IORESOURCE_IRQ;
>  		r->name = name ? name : dev->full_name;
> +
> +		/*
> +		 * Some drivers might rely on availability of trigger flags
> +		 * in IRQ resource. Since irq_of_parse_and_map() configures the
> +		 * trigger based on interrupt specifier and IRQD_TRIGGER_*
> +		 * flags are consistent with IORESOURCE_IRQ_*, we can get
> +		 * trigger type that was just set and pass it through resource
> +		 * flags as well.
> +		 */
> +		r->flags |= irqd_get_trigger_type(irq_get_irq_data(irq));
>  	}
>  
>  	return irq;
> -- 
> 1.8.3.2
> 

Re: [PATCH] of: irq: Pass trigger type in IRQ resource flags

[Grant Likely]

On Sat, 28 Sep 2013 19:52:51 +0200, Tomasz Figa <tomasz.figa@gmail.com> wrote:
> Some drivers might rely on availability of trigger flags in IRQ
> resource, for example to configure the hardware for particular interrupt
> type. However current code creating IRQ resources from data in device
> tree does not configure trigger flags in resulting resources.
> 
> This patch tries to solve the problem, based on the fact that
> irq_of_parse_and_map() configures the trigger based on DT interrupt
> specifier and IRQD_TRIGGER_* flags are consistent with IORESOURCE_IRQ_*,
> and we can get correct trigger flags by calling irqd_get_trigger_type()
> after mapping the interrupt.
> 
> Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>

Applied, thanks.

g.

> ---
>  drivers/of/irq.c | 10 ++++++++++
>  1 file changed, 10 insertions(+)
> 
> diff --git a/drivers/of/irq.c b/drivers/of/irq.c
> index 1752988..12742d0 100644
> --- a/drivers/of/irq.c
> +++ b/drivers/of/irq.c
> @@ -356,6 +356,16 @@ int of_irq_to_resource(struct device_node *dev, int index, struct resource *r)
>  		r->start = r->end = irq;
>  		r->flags = IORESOURCE_IRQ;
>  		r->name = name ? name : dev->full_name;
> +
> +		/*
> +		 * Some drivers might rely on availability of trigger flags
> +		 * in IRQ resource. Since irq_of_parse_and_map() configures the
> +		 * trigger based on interrupt specifier and IRQD_TRIGGER_*
> +		 * flags are consistent with IORESOURCE_IRQ_*, we can get
> +		 * trigger type that was just set and pass it through resource
> +		 * flags as well.
> +		 */
> +		r->flags |= irqd_get_trigger_type(irq_get_irq_data(irq));
>  	}
>  
>  	return irq;
> -- 
> 1.8.3.2
>