[PATCHv4 0/8] ARM: mxs: Various Crystalfontz DT additions

[PATCHv4 0/8] ARM: mxs: Various Crystalfontz DT additions

[Alexandre Belloni]

Hi,

This patch series add DT for the Crystalfontz CFA-10056 and Crystalfontz
CFA-10058.

The first patch simplifies board detection in mach-mxs.c as suggested by Thomas
Petazzoni in his review of the precedent DT additions.

The next two patches are adding the DTs.

The last patches are cleaning up the remaining boards DTs.

Changes in v4
 - corrected comment for cfa-10056 and made it cfa-10037 compatible
 - reordered patches

Changes in v3
 - Cleaned up all the DTs for crystalfontz boards.

Changes in v2:
 - took into account the review from Maxime Ripard

Thanks,

Alexandre Belloni (6):
  ARM: mxs: Simplify detection of CrystalFontz boards
  ARM: mxs: dt: cfa10037: make hogpins grabbed by respective drivers
  ARM: mxs: dt: cfa10049: make hogpins grabbed by respective drivers
  ARM: mxs: dt: cfa10055: make hogpins grabbed by respective drivers
  ARM: mxs: dt: cfa10057: remove hogpins
  ARM: mxs: dt: cfa10036: make hogpins grabbed by respective drivers

Brian Lilly (2):
  ARM: mxs: dt: Add Crystalfontz CFA-10056 device tree
  ARM: mxs: dt: Add Crystalfontz CFA-10058 device tree

 arch/arm/boot/dts/Makefile           |   2 +
 arch/arm/boot/dts/imx28-cfa10036.dts |   7 +-
 arch/arm/boot/dts/imx28-cfa10037.dts |  19 +++--
 arch/arm/boot/dts/imx28-cfa10049.dts |  73 +++++++++++++++---
 arch/arm/boot/dts/imx28-cfa10055.dts |  38 ++++------
 arch/arm/boot/dts/imx28-cfa10056.dts | 119 +++++++++++++++++++++++++++++
 arch/arm/boot/dts/imx28-cfa10057.dts |  23 +-----
 arch/arm/boot/dts/imx28-cfa10058.dts | 141 +++++++++++++++++++++++++++++++++++
 arch/arm/mach-mxs/mach-mxs.c         |   5 +-
 9 files changed, 359 insertions(+), 68 deletions(-)
 create mode 100644 arch/arm/boot/dts/imx28-cfa10056.dts
 create mode 100644 arch/arm/boot/dts/imx28-cfa10058.dts

-- 
1.8.1.2

[PATCHv4 0/8] ARM: mxs: Various Crystalfontz DT additions

[Alexandre Belloni]

Hi,

This patch series add DT for the Crystalfontz CFA-10056 and Crystalfontz
CFA-10058.

The first patch simplifies board detection in mach-mxs.c as suggested by Thomas
Petazzoni in his review of the precedent DT additions.

The next two patches are adding the DTs.

The last patches are cleaning up the remaining boards DTs.

Changes in v4
 - corrected comment for cfa-10056 and made it cfa-10037 compatible
 - reordered patches

Changes in v3
 - Cleaned up all the DTs for crystalfontz boards.

Changes in v2:
 - took into account the review from Maxime Ripard

Thanks,

Alexandre Belloni (6):
  ARM: mxs: Simplify detection of CrystalFontz boards
  ARM: mxs: dt: cfa10037: make hogpins grabbed by respective drivers
  ARM: mxs: dt: cfa10049: make hogpins grabbed by respective drivers
  ARM: mxs: dt: cfa10055: make hogpins grabbed by respective drivers
  ARM: mxs: dt: cfa10057: remove hogpins
  ARM: mxs: dt: cfa10036: make hogpins grabbed by respective drivers

Brian Lilly (2):
  ARM: mxs: dt: Add Crystalfontz CFA-10056 device tree
  ARM: mxs: dt: Add Crystalfontz CFA-10058 device tree

 arch/arm/boot/dts/Makefile           |   2 +
 arch/arm/boot/dts/imx28-cfa10036.dts |   7 +-
 arch/arm/boot/dts/imx28-cfa10037.dts |  19 +++--
 arch/arm/boot/dts/imx28-cfa10049.dts |  73 +++++++++++++++---
 arch/arm/boot/dts/imx28-cfa10055.dts |  38 ++++------
 arch/arm/boot/dts/imx28-cfa10056.dts | 119 +++++++++++++++++++++++++++++
 arch/arm/boot/dts/imx28-cfa10057.dts |  23 +-----
 arch/arm/boot/dts/imx28-cfa10058.dts | 141 +++++++++++++++++++++++++++++++++++
 arch/arm/mach-mxs/mach-mxs.c         |   5 +-
 9 files changed, 359 insertions(+), 68 deletions(-)
 create mode 100644 arch/arm/boot/dts/imx28-cfa10056.dts
 create mode 100644 arch/arm/boot/dts/imx28-cfa10058.dts

-- 
1.8.1.2

[PATCHv4 1/8] ARM: mxs: Simplify detection of CrystalFontz boards

[Alexandre Belloni]

As all CrystalFontz boards are compatible with "crystalfontz,cfa10036", make it
easier to add future boards.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
 arch/arm/mach-mxs/mach-mxs.c | 5 +----
 1 file changed, 1 insertion(+), 4 deletions(-)

diff --git a/arch/arm/mach-mxs/mach-mxs.c b/arch/arm/mach-mxs/mach-mxs.c
index 6298adb..1b8c274 100644
--- a/arch/arm/mach-mxs/mach-mxs.c
+++ b/arch/arm/mach-mxs/mach-mxs.c
@@ -478,10 +478,7 @@ static void __init mxs_machine_init(void)
 		imx28_evk_init();
 	else if (of_machine_is_compatible("bluegiga,apx4devkit"))
 		apx4devkit_init();
-	else if (of_machine_is_compatible("crystalfontz,cfa10037") ||
-		 of_machine_is_compatible("crystalfontz,cfa10049") ||
-		 of_machine_is_compatible("crystalfontz,cfa10055") ||
-		 of_machine_is_compatible("crystalfontz,cfa10057"))
+	else if (of_machine_is_compatible("crystalfontz,cfa10036"))
 		crystalfontz_init();
 
 	of_platform_populate(NULL, of_default_bus_match_table,
-- 
1.8.1.2

[PATCHv4 1/8] ARM: mxs: Simplify detection of CrystalFontz boards

[Alexandre Belloni]

As all CrystalFontz boards are compatible with "crystalfontz,cfa10036", make it
easier to add future boards.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
 arch/arm/mach-mxs/mach-mxs.c | 5 +----
 1 file changed, 1 insertion(+), 4 deletions(-)

diff --git a/arch/arm/mach-mxs/mach-mxs.c b/arch/arm/mach-mxs/mach-mxs.c
index 6298adb..1b8c274 100644
--- a/arch/arm/mach-mxs/mach-mxs.c
+++ b/arch/arm/mach-mxs/mach-mxs.c
@@ -478,10 +478,7 @@ static void __init mxs_machine_init(void)
 		imx28_evk_init();
 	else if (of_machine_is_compatible("bluegiga,apx4devkit"))
 		apx4devkit_init();
-	else if (of_machine_is_compatible("crystalfontz,cfa10037") ||
-		 of_machine_is_compatible("crystalfontz,cfa10049") ||
-		 of_machine_is_compatible("crystalfontz,cfa10055") ||
-		 of_machine_is_compatible("crystalfontz,cfa10057"))
+	else if (of_machine_is_compatible("crystalfontz,cfa10036"))
 		crystalfontz_init();
 
 	of_platform_populate(NULL, of_default_bus_match_table,
-- 
1.8.1.2

[PATCHv4 2/8] ARM: mxs: dt: Add Crystalfontz CFA-10056 device tree

[Alexandre Belloni]

From: Brian Lilly <brian@crystalfontz.com>

The CFA-10056 is a breakout board for the CFA-10036, and is
basically a CFA-10037, with a 4.3" screen.

Signed-off-by: Brian Lilly <brian@crystalfontz.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/Makefile           |   1 +
 arch/arm/boot/dts/imx28-cfa10056.dts | 119 +++++++++++++++++++++++++++++++++++
 2 files changed, 120 insertions(+)
 create mode 100644 arch/arm/boot/dts/imx28-cfa10056.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 641b3c9..da75139 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -143,6 +143,7 @@ dtb-$(CONFIG_ARCH_MXS) += imx23-evk.dtb \
 	imx28-cfa10037.dtb \
 	imx28-cfa10049.dtb \
 	imx28-cfa10055.dtb \
+	imx28-cfa10056.dtb \
 	imx28-cfa10057.dtb \
 	imx28-evk.dtb \
 	imx28-m28evk.dtb \
diff --git a/arch/arm/boot/dts/imx28-cfa10056.dts b/arch/arm/boot/dts/imx28-cfa10056.dts
new file mode 100644
index 0000000..b45dd0e
--- /dev/null
+++ b/arch/arm/boot/dts/imx28-cfa10056.dts
@@ -0,0 +1,119 @@
+/*
+ * Copyright 2013 Free Electrons
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/*
+ * The CFA-10055 is an expansion board for the CFA-10036 module and
+ * CFA-10037, thus we need to include the CFA-10037 DTS.
+ */
+/include/ "imx28-cfa10037.dts"
+
+/ {
+	model = "Crystalfontz CFA-10056 Board";
+	compatible = "crystalfontz,cfa10056", "crystalfontz,cfa10037", "crystalfontz,cfa10036", "fsl,imx28";
+
+	apb at 80000000 {
+		apbh at 80000000 {
+			pinctrl at 80018000 {
+				spi2_pins_cfa10056: spi2-cfa10056 at 0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						0x2103 /* MX28_PAD_SSP2_SCK__GPIO_2_16 */
+						0x2113 /* MX28_PAD_SSP2_CMD__GPIO_2_17 */
+						0x2123 /* MX28_PAD_SSP2_D0__GPIO_2_18 */
+						0x3053 /* MX28_PAD_AUART1_TX__GPIO_3_5 */
+					>;
+					fsl,drive-strength = <1>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <1>;
+				};
+
+				lcdif_pins_cfa10056: lcdif-10056 at 0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */
+						0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */
+						0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */
+						0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */
+					>;
+					fsl,drive-strength = <0>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <0>;
+				};
+
+				lcdif_pins_cfa10056_pullup: lcdif-10056-pullup at 0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						0x31e3 /* MX28_PAD_LCD_RESET__GPIO_3_30 */
+					>;
+					fsl,drive-strength = <0>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <1>;
+				};
+			};
+
+			lcdif at 80030000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&lcdif_24bit_pins_a
+						&lcdif_pins_cfa10056
+						&lcdif_pins_cfa10056_pullup >;
+				display = <&display>;
+				status = "okay";
+
+				display: display {
+					bits-per-pixel = <32>;
+					bus-width = <24>;
+
+					display-timings {
+						native-mode = <&timing0>;
+						timing0: timing0 {
+							clock-frequency = <32000000>;
+							hactive = <480>;
+							vactive = <800>;
+							hback-porch = <2>;
+							hfront-porch = <2>;
+							vback-porch = <2>;
+							vfront-porch = <2>;
+							hsync-len = <5>;
+							vsync-len = <5>;
+							hsync-active = <0>;
+							vsync-active = <0>;
+							de-active = <1>;
+							pixelclk-active = <1>;
+						};
+					};
+				};
+			};
+		};
+	};
+
+	spi2 {
+		compatible = "spi-gpio";
+		pinctrl-names = "default";
+		pinctrl-0 = <&spi2_pins_cfa10056>;
+		status = "okay";
+		gpio-sck = <&gpio2 16 0>;
+		gpio-mosi = <&gpio2 17 0>;
+		gpio-miso = <&gpio2 18 0>;
+		cs-gpios = <&gpio3 5 0>;
+		num-chipselects = <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		hx8369: hx8369 at 0 {
+			compatible = "himax,hx8369a", "himax,hx8369";
+			reg = <0>;
+			spi-max-frequency = <100000>;
+			spi-cpol;
+			spi-cpha;
+			gpios-reset = <&gpio3 30 0>;
+		};
+	};
+};
-- 
1.8.1.2

[PATCHv4 2/8] ARM: mxs: dt: Add Crystalfontz CFA-10056 device tree

[Alexandre Belloni]

From: Brian Lilly <brian@crystalfontz.com>

The CFA-10056 is a breakout board for the CFA-10036, and is
basically a CFA-10037, with a 4.3" screen.

Signed-off-by: Brian Lilly <brian@crystalfontz.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/Makefile           |   1 +
 arch/arm/boot/dts/imx28-cfa10056.dts | 119 +++++++++++++++++++++++++++++++++++
 2 files changed, 120 insertions(+)
 create mode 100644 arch/arm/boot/dts/imx28-cfa10056.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 641b3c9..da75139 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -143,6 +143,7 @@ dtb-$(CONFIG_ARCH_MXS) += imx23-evk.dtb \
 	imx28-cfa10037.dtb \
 	imx28-cfa10049.dtb \
 	imx28-cfa10055.dtb \
+	imx28-cfa10056.dtb \
 	imx28-cfa10057.dtb \
 	imx28-evk.dtb \
 	imx28-m28evk.dtb \
diff --git a/arch/arm/boot/dts/imx28-cfa10056.dts b/arch/arm/boot/dts/imx28-cfa10056.dts
new file mode 100644
index 0000000..b45dd0e
--- /dev/null
+++ b/arch/arm/boot/dts/imx28-cfa10056.dts
@@ -0,0 +1,119 @@
+/*
+ * Copyright 2013 Free Electrons
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/*
+ * The CFA-10055 is an expansion board for the CFA-10036 module and
+ * CFA-10037, thus we need to include the CFA-10037 DTS.
+ */
+/include/ "imx28-cfa10037.dts"
+
+/ {
+	model = "Crystalfontz CFA-10056 Board";
+	compatible = "crystalfontz,cfa10056", "crystalfontz,cfa10037", "crystalfontz,cfa10036", "fsl,imx28";
+
+	apb@80000000 {
+		apbh@80000000 {
+			pinctrl@80018000 {
+				spi2_pins_cfa10056: spi2-cfa10056@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						0x2103 /* MX28_PAD_SSP2_SCK__GPIO_2_16 */
+						0x2113 /* MX28_PAD_SSP2_CMD__GPIO_2_17 */
+						0x2123 /* MX28_PAD_SSP2_D0__GPIO_2_18 */
+						0x3053 /* MX28_PAD_AUART1_TX__GPIO_3_5 */
+					>;
+					fsl,drive-strength = <1>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <1>;
+				};
+
+				lcdif_pins_cfa10056: lcdif-10056@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */
+						0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */
+						0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */
+						0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */
+					>;
+					fsl,drive-strength = <0>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <0>;
+				};
+
+				lcdif_pins_cfa10056_pullup: lcdif-10056-pullup@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						0x31e3 /* MX28_PAD_LCD_RESET__GPIO_3_30 */
+					>;
+					fsl,drive-strength = <0>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <1>;
+				};
+			};
+
+			lcdif@80030000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&lcdif_24bit_pins_a
+						&lcdif_pins_cfa10056
+						&lcdif_pins_cfa10056_pullup >;
+				display = <&display>;
+				status = "okay";
+
+				display: display {
+					bits-per-pixel = <32>;
+					bus-width = <24>;
+
+					display-timings {
+						native-mode = <&timing0>;
+						timing0: timing0 {
+							clock-frequency = <32000000>;
+							hactive = <480>;
+							vactive = <800>;
+							hback-porch = <2>;
+							hfront-porch = <2>;
+							vback-porch = <2>;
+							vfront-porch = <2>;
+							hsync-len = <5>;
+							vsync-len = <5>;
+							hsync-active = <0>;
+							vsync-active = <0>;
+							de-active = <1>;
+							pixelclk-active = <1>;
+						};
+					};
+				};
+			};
+		};
+	};
+
+	spi2 {
+		compatible = "spi-gpio";
+		pinctrl-names = "default";
+		pinctrl-0 = <&spi2_pins_cfa10056>;
+		status = "okay";
+		gpio-sck = <&gpio2 16 0>;
+		gpio-mosi = <&gpio2 17 0>;
+		gpio-miso = <&gpio2 18 0>;
+		cs-gpios = <&gpio3 5 0>;
+		num-chipselects = <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		hx8369: hx8369@0 {
+			compatible = "himax,hx8369a", "himax,hx8369";
+			reg = <0>;
+			spi-max-frequency = <100000>;
+			spi-cpol;
+			spi-cpha;
+			gpios-reset = <&gpio3 30 0>;
+		};
+	};
+};
-- 
1.8.1.2

[PATCHv4 3/8] ARM: mxs: dt: Add Crystalfontz CFA-10058 device tree

[Alexandre Belloni]

From: Brian Lilly <brian@crystalfontz.com>

The CFA-10058 is a breakout board for the CFA-10036 that has Ethernet, USB and a
5" LCD screen on it.

Signed-off-by: Brian Lilly <brian@crystalfontz.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
 arch/arm/boot/dts/Makefile           |   1 +
 arch/arm/boot/dts/imx28-cfa10058.dts | 141 +++++++++++++++++++++++++++++++++++
 2 files changed, 142 insertions(+)
 create mode 100644 arch/arm/boot/dts/imx28-cfa10058.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index da75139..92d66cf 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -145,6 +145,7 @@ dtb-$(CONFIG_ARCH_MXS) += imx23-evk.dtb \
 	imx28-cfa10055.dtb \
 	imx28-cfa10056.dtb \
 	imx28-cfa10057.dtb \
+	imx28-cfa10058.dtb \
 	imx28-evk.dtb \
 	imx28-m28evk.dtb \
 	imx28-sps1.dtb \
diff --git a/arch/arm/boot/dts/imx28-cfa10058.dts b/arch/arm/boot/dts/imx28-cfa10058.dts
new file mode 100644
index 0000000..64c64c5
--- /dev/null
+++ b/arch/arm/boot/dts/imx28-cfa10058.dts
@@ -0,0 +1,141 @@
+/*
+ * Copyright 2013 Crystalfontz America, Inc.
+ * Copyright 2013 Free Electrons
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/*
+ * The CFA-10058 is an expansion board for the CFA-10036 module, thus we
+ * need to include the CFA-10036 DTS.
+ */
+/include/ "imx28-cfa10036.dts"
+
+/ {
+	model = "Crystalfontz CFA-10058 Board";
+	compatible = "crystalfontz,cfa10058", "crystalfontz,cfa10036", "fsl,imx28";
+
+	apb at 80000000 {
+		apbh at 80000000 {
+			pinctrl at 80018000 {
+				usb_pins_cfa10058: usb-10058 at 0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						0x0073 /* MX28_PAD_GPMI_D7__GPIO_0_7 */
+					>;
+					fsl,drive-strength = <0>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <0>;
+				};
+
+				lcdif_pins_cfa10058: lcdif-10058 at 0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */
+						0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */
+						0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */
+						0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */
+					>;
+					fsl,drive-strength = <0>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <0>;
+				};
+			};
+
+			lcdif at 80030000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&lcdif_24bit_pins_a
+						 &lcdif_pins_cfa10058>;
+				display = <&display>;
+				status = "okay";
+
+				display: display {
+					bits-per-pixel = <32>;
+					bus-width = <24>;
+
+					display-timings {
+						native-mode = <&timing0>;
+						timing0: timing0 {
+							clock-frequency = <30000000>;
+							hactive = <800>;
+							vactive = <480>;
+							hback-porch = <40>;
+							hfront-porch = <40>;
+							vback-porch = <13>;
+							vfront-porch = <29>;
+							hsync-len = <8>;
+							vsync-len = <8>;
+							hsync-active = <0>;
+							vsync-active = <0>;
+							de-active = <1>;
+							pixelclk-active = <1>;
+						};
+					};
+				};
+			};
+		};
+
+		apbx at 80040000 {
+			lradc at 80050000 {
+				fsl,lradc-touchscreen-wires = <4>;
+				status = "okay";
+			};
+
+			pwm: pwm at 80064000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pwm3_pins_b>;
+				status = "okay";
+			};
+
+			usbphy1: usbphy at 8007e000 {
+				status = "okay";
+			};
+		};
+	};
+
+	ahb at 80080000 {
+		usb1: usb at 80090000 {
+			vbus-supply = <&reg_usb1_vbus>;
+			pinctrl-0 = <&usbphy1_pins_a>;
+			pinctrl-names = "default";
+			status = "okay";
+		};
+	};
+
+	regulators {
+		compatible = "simple-bus";
+
+		reg_usb1_vbus: usb1_vbus {
+			pinctrl-names = "default";
+			pinctrl-0 = <&usb_pins_cfa10058>;
+			compatible = "regulator-fixed";
+			regulator-name = "usb1_vbus";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			gpio = <&gpio0 7 1>;
+		};
+	};
+
+	ahb at 80080000 {
+		mac0: ethernet at 800f0000 {
+			phy-mode = "rmii";
+			pinctrl-names = "default";
+			pinctrl-0 = <&mac0_pins_a>;
+			phy-reset-gpios = <&gpio2 21 0>;
+			phy-reset-duration = <100>;
+			status = "okay";
+		};
+	};
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 3 5000000>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <6>;
+	};
+};
-- 
1.8.1.2

[PATCHv4 3/8] ARM: mxs: dt: Add Crystalfontz CFA-10058 device tree

[Alexandre Belloni]

From: Brian Lilly <brian@crystalfontz.com>

The CFA-10058 is a breakout board for the CFA-10036 that has Ethernet, USB and a
5" LCD screen on it.

Signed-off-by: Brian Lilly <brian@crystalfontz.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
 arch/arm/boot/dts/Makefile           |   1 +
 arch/arm/boot/dts/imx28-cfa10058.dts | 141 +++++++++++++++++++++++++++++++++++
 2 files changed, 142 insertions(+)
 create mode 100644 arch/arm/boot/dts/imx28-cfa10058.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index da75139..92d66cf 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -145,6 +145,7 @@ dtb-$(CONFIG_ARCH_MXS) += imx23-evk.dtb \
 	imx28-cfa10055.dtb \
 	imx28-cfa10056.dtb \
 	imx28-cfa10057.dtb \
+	imx28-cfa10058.dtb \
 	imx28-evk.dtb \
 	imx28-m28evk.dtb \
 	imx28-sps1.dtb \
diff --git a/arch/arm/boot/dts/imx28-cfa10058.dts b/arch/arm/boot/dts/imx28-cfa10058.dts
new file mode 100644
index 0000000..64c64c5
--- /dev/null
+++ b/arch/arm/boot/dts/imx28-cfa10058.dts
@@ -0,0 +1,141 @@
+/*
+ * Copyright 2013 Crystalfontz America, Inc.
+ * Copyright 2013 Free Electrons
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/*
+ * The CFA-10058 is an expansion board for the CFA-10036 module, thus we
+ * need to include the CFA-10036 DTS.
+ */
+/include/ "imx28-cfa10036.dts"
+
+/ {
+	model = "Crystalfontz CFA-10058 Board";
+	compatible = "crystalfontz,cfa10058", "crystalfontz,cfa10036", "fsl,imx28";
+
+	apb@80000000 {
+		apbh@80000000 {
+			pinctrl@80018000 {
+				usb_pins_cfa10058: usb-10058@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						0x0073 /* MX28_PAD_GPMI_D7__GPIO_0_7 */
+					>;
+					fsl,drive-strength = <0>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <0>;
+				};
+
+				lcdif_pins_cfa10058: lcdif-10058@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */
+						0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */
+						0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */
+						0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */
+					>;
+					fsl,drive-strength = <0>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <0>;
+				};
+			};
+
+			lcdif@80030000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&lcdif_24bit_pins_a
+						 &lcdif_pins_cfa10058>;
+				display = <&display>;
+				status = "okay";
+
+				display: display {
+					bits-per-pixel = <32>;
+					bus-width = <24>;
+
+					display-timings {
+						native-mode = <&timing0>;
+						timing0: timing0 {
+							clock-frequency = <30000000>;
+							hactive = <800>;
+							vactive = <480>;
+							hback-porch = <40>;
+							hfront-porch = <40>;
+							vback-porch = <13>;
+							vfront-porch = <29>;
+							hsync-len = <8>;
+							vsync-len = <8>;
+							hsync-active = <0>;
+							vsync-active = <0>;
+							de-active = <1>;
+							pixelclk-active = <1>;
+						};
+					};
+				};
+			};
+		};
+
+		apbx@80040000 {
+			lradc@80050000 {
+				fsl,lradc-touchscreen-wires = <4>;
+				status = "okay";
+			};
+
+			pwm: pwm@80064000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pwm3_pins_b>;
+				status = "okay";
+			};
+
+			usbphy1: usbphy@8007e000 {
+				status = "okay";
+			};
+		};
+	};
+
+	ahb@80080000 {
+		usb1: usb@80090000 {
+			vbus-supply = <&reg_usb1_vbus>;
+			pinctrl-0 = <&usbphy1_pins_a>;
+			pinctrl-names = "default";
+			status = "okay";
+		};
+	};
+
+	regulators {
+		compatible = "simple-bus";
+
+		reg_usb1_vbus: usb1_vbus {
+			pinctrl-names = "default";
+			pinctrl-0 = <&usb_pins_cfa10058>;
+			compatible = "regulator-fixed";
+			regulator-name = "usb1_vbus";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			gpio = <&gpio0 7 1>;
+		};
+	};
+
+	ahb@80080000 {
+		mac0: ethernet@800f0000 {
+			phy-mode = "rmii";
+			pinctrl-names = "default";
+			pinctrl-0 = <&mac0_pins_a>;
+			phy-reset-gpios = <&gpio2 21 0>;
+			phy-reset-duration = <100>;
+			status = "okay";
+		};
+	};
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 3 5000000>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <6>;
+	};
+};
-- 
1.8.1.2

[PATCHv4 4/8] ARM: mxs: dt: cfa10037: make hogpins grabbed by respective drivers

[Alexandre Belloni]

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
 arch/arm/boot/dts/imx28-cfa10037.dts | 19 ++++++++++++++-----
 1 file changed, 14 insertions(+), 5 deletions(-)

diff --git a/arch/arm/boot/dts/imx28-cfa10037.dts b/arch/arm/boot/dts/imx28-cfa10037.dts
index c2ef3a3..182b99f 100644
--- a/arch/arm/boot/dts/imx28-cfa10037.dts
+++ b/arch/arm/boot/dts/imx28-cfa10037.dts
@@ -22,13 +22,19 @@
 	apb at 80000000 {
 		apbh at 80000000 {
 			pinctrl at 80018000 {
-				pinctrl-names = "default", "default";
-				pinctrl-1 = <&hog_pins_cfa10037>;
-
-				hog_pins_cfa10037: hog-10037 at 0 {
+				usb_pins_cfa10037: usb-10037 at 0 {
 					reg = <0>;
 					fsl,pinmux-ids = <
 						0x0073 /* MX28_PAD_GPMI_D7__GPIO_0_7 */
+					>;
+					fsl,drive-strength = <0>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <0>;
+				};
+
+				mac0_pins_cfa10037: mac0-10037 at 0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
 						0x2153 /* MX28_PAD_SSP2_D5__GPIO_2_21 */
 					>;
 					fsl,drive-strength = <0>;
@@ -56,7 +62,8 @@
 		mac0: ethernet at 800f0000 {
 			phy-mode = "rmii";
 			pinctrl-names = "default";
-			pinctrl-0 = <&mac0_pins_a>;
+			pinctrl-0 = <&mac0_pins_a
+				&mac0_pins_cfa10037>;
 			phy-reset-gpios = <&gpio2 21 0>;
 			phy-reset-duration = <100>;
 			status = "okay";
@@ -68,6 +75,8 @@
 
 		reg_usb1_vbus: usb1_vbus {
 			compatible = "regulator-fixed";
+			pinctrl-names = "default";
+			pinctrl-0 = <&usb_pins_cfa10037>;
 			regulator-name = "usb1_vbus";
 			regulator-min-microvolt = <5000000>;
 			regulator-max-microvolt = <5000000>;
-- 
1.8.1.2

[PATCHv4 4/8] ARM: mxs: dt: cfa10037: make hogpins grabbed by respective drivers

[Alexandre Belloni]

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
 arch/arm/boot/dts/imx28-cfa10037.dts | 19 ++++++++++++++-----
 1 file changed, 14 insertions(+), 5 deletions(-)

diff --git a/arch/arm/boot/dts/imx28-cfa10037.dts b/arch/arm/boot/dts/imx28-cfa10037.dts
index c2ef3a3..182b99f 100644
--- a/arch/arm/boot/dts/imx28-cfa10037.dts
+++ b/arch/arm/boot/dts/imx28-cfa10037.dts
@@ -22,13 +22,19 @@
 	apb@80000000 {
 		apbh@80000000 {
 			pinctrl@80018000 {
-				pinctrl-names = "default", "default";
-				pinctrl-1 = <&hog_pins_cfa10037>;
-
-				hog_pins_cfa10037: hog-10037@0 {
+				usb_pins_cfa10037: usb-10037@0 {
 					reg = <0>;
 					fsl,pinmux-ids = <
 						0x0073 /* MX28_PAD_GPMI_D7__GPIO_0_7 */
+					>;
+					fsl,drive-strength = <0>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <0>;
+				};
+
+				mac0_pins_cfa10037: mac0-10037@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
 						0x2153 /* MX28_PAD_SSP2_D5__GPIO_2_21 */
 					>;
 					fsl,drive-strength = <0>;
@@ -56,7 +62,8 @@
 		mac0: ethernet@800f0000 {
 			phy-mode = "rmii";
 			pinctrl-names = "default";
-			pinctrl-0 = <&mac0_pins_a>;
+			pinctrl-0 = <&mac0_pins_a
+				&mac0_pins_cfa10037>;
 			phy-reset-gpios = <&gpio2 21 0>;
 			phy-reset-duration = <100>;
 			status = "okay";
@@ -68,6 +75,8 @@
 
 		reg_usb1_vbus: usb1_vbus {
 			compatible = "regulator-fixed";
+			pinctrl-names = "default";
+			pinctrl-0 = <&usb_pins_cfa10037>;
 			regulator-name = "usb1_vbus";
 			regulator-min-microvolt = <5000000>;
 			regulator-max-microvolt = <5000000>;
-- 
1.8.1.2

[PATCHv4 5/8] ARM: mxs: dt: cfa10049: make hogpins grabbed by respective drivers

[Alexandre Belloni]

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
 arch/arm/boot/dts/imx28-cfa10049.dts | 73 +++++++++++++++++++++++++++++++-----
 1 file changed, 63 insertions(+), 10 deletions(-)

diff --git a/arch/arm/boot/dts/imx28-cfa10049.dts b/arch/arm/boot/dts/imx28-cfa10049.dts
index 04b2f76..06e4cfa 100644
--- a/arch/arm/boot/dts/imx28-cfa10049.dts
+++ b/arch/arm/boot/dts/imx28-cfa10049.dts
@@ -22,32 +22,62 @@
 	apb at 80000000 {
 		apbh at 80000000 {
 			pinctrl at 80018000 {
-				pinctrl-names = "default", "default";
-				pinctrl-1 = <&hog_pins_cfa10049
-					&hog_pins_cfa10049_pullup>;
-
-				hog_pins_cfa10049: hog-10049 at 0 {
+				usb_pins_cfa10049: usb-10049 at 0 {
 					reg = <0>;
 					fsl,pinmux-ids = <
 						0x0073 /* MX28_PAD_GPMI_D7__GPIO_0_7 */
+					>;
+					fsl,drive-strength = <0>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <0>;
+				};
+
+				i2cmux_pins_cfa10049: i2cmux-10049 at 0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
 						0x1163 /* MX28_PAD_LCD_D22__GPIO_1_22 */
 						0x1173 /* MX28_PAD_LCD_D22__GPIO_1_23 */
+					>;
+					fsl,drive-strength = <0>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <0>;
+				};
+
+				mac0_pins_cfa10049: mac0-10049 at 0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
 						0x2153 /* MX28_PAD_SSP2_D5__GPIO_2_21 */
-						0x3053 /* MX28_PAD_AUART1_TX__GPIO_3_5 */
 					>;
 					fsl,drive-strength = <0>;
 					fsl,voltage = <1>;
 					fsl,pull-up = <0>;
 				};
 
-				hog_pins_cfa10049_pullup: hog-10049-pullup at 0 {
+				pca_pins_cfa10049: pca-10049 at 0 {
 					reg = <0>;
 					fsl,pinmux-ids = <
 						0x2133 /* MX28_PAD_SSP2_D3__GPIO_2_19 */
+					>;
+					fsl,drive-strength = <0>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <1>;
+				};
+
+				rotary_pins_cfa10049: rotary-10049 at 0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
 						0x3183 /* MX28_PAD_I2C0_SCL__GPIO_3_24 */
 						0x3193 /* MX28_PAD_I2C0_SDA__GPIO_3_25 */
+					>;
+					fsl,drive-strength = <0>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <1>;
+				};
+
+				rotary_btn_pins_cfa10049: rotary-btn-10049 at 0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
 						0x31a3 /* MX28_PAD_SAIF_SDATA0__GPIO_3_26 */
-						0x31e3 /* MX28_PAD_LCD_RESET__GPIO_3_30 */
 					>;
 					fsl,drive-strength = <0>;
 					fsl,voltage = <1>;
@@ -60,6 +90,7 @@
 						0x2103 /* MX28_PAD_SSP2_SCK__GPIO_2_16 */
 						0x2113 /* MX28_PAD_SSP2_CMD__GPIO_2_17 */
 						0x2123 /* MX28_PAD_SSP2_D0__GPIO_2_18 */
+						0x3053 /* MX28_PAD_AUART1_TX__GPIO_3_5 */
 					>;
 					fsl,drive-strength = <1>;
 					fsl,voltage = <1>;
@@ -120,6 +151,16 @@
 					fsl,pull-up = <0>;
 				};
 
+				lcdif_pins_cfa10049_pullup: lcdif-10049-pullup at 0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						0x31e3 /* MX28_PAD_LCD_RESET__GPIO_3_30 */
+					>;
+					fsl,drive-strength = <0>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <1>;
+				};
+
 				w1_gpio_pins: w1-gpio at 0 {
 					reg = <0>;
 					fsl,pinmux-ids = <
@@ -134,7 +175,8 @@
 			lcdif@80030000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&lcdif_18bit_pins_cfa10049
-					     &lcdif_pins_cfa10049>;
+					     &lcdif_pins_cfa10049
+					     &lcdif_pins_cfa10049_pullup>;
 				display = <&display>;
 				status = "okay";
 
@@ -181,6 +223,8 @@
 				compatible = "i2c-mux-gpio";
 				#address-cells = <1>;
 				#size-cells = <0>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&i2cmux_pins_cfa10049>;
 				mux-gpios = <&gpio1 22 0 &gpio1 23 0>;
 				i2c-parent = <&i2c1>;
 
@@ -203,6 +247,8 @@
 
 					pca9555: pca9555 at 20 {
 						compatible = "nxp,pca9555";
+						pinctrl-names = "default";
+						pinctrl-0 = <&pca_pins_cfa10049>;
 						interrupt-parent = <&gpio2>;
 						interrupts = <19 0x2>;
 						gpio-controller;
@@ -239,6 +285,8 @@
 
 		reg_usb1_vbus: usb1_vbus {
 			compatible = "regulator-fixed";
+			pinctrl-names = "default";
+			pinctrl-0 = <&usb_pins_cfa10049>;
 			regulator-name = "usb1_vbus";
 			regulator-min-microvolt = <5000000>;
 			regulator-max-microvolt = <5000000>;
@@ -250,7 +298,8 @@
 		mac0: ethernet at 800f0000 {
 			phy-mode = "rmii";
 			pinctrl-names = "default";
-			pinctrl-0 = <&mac0_pins_a>;
+			pinctrl-0 = <&mac0_pins_a
+				&mac0_pins_cfa10049>;
 			phy-reset-gpios = <&gpio2 21 0>;
 			phy-reset-duration = <100>;
 			status = "okay";
@@ -320,6 +369,8 @@
 
 	gpio_keys {
 		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&rotary_btn_pins_cfa10049>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 
@@ -333,6 +384,8 @@
 
 	rotary {
 		compatible = "rotary-encoder";
+		pinctrl-names = "default";
+		pinctrl-0 = <&rotary_pins_cfa10049>;
 		gpios = <&gpio3 24 1>, <&gpio3 25 1>;
 		linux,axis = <1>; /* REL_Y */
 		rotary-encoder,relative-axis;
-- 
1.8.1.2

[PATCHv4 5/8] ARM: mxs: dt: cfa10049: make hogpins grabbed by respective drivers

[Alexandre Belloni]

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
 arch/arm/boot/dts/imx28-cfa10049.dts | 73 +++++++++++++++++++++++++++++++-----
 1 file changed, 63 insertions(+), 10 deletions(-)

diff --git a/arch/arm/boot/dts/imx28-cfa10049.dts b/arch/arm/boot/dts/imx28-cfa10049.dts
index 04b2f76..06e4cfa 100644
--- a/arch/arm/boot/dts/imx28-cfa10049.dts
+++ b/arch/arm/boot/dts/imx28-cfa10049.dts
@@ -22,32 +22,62 @@
 	apb@80000000 {
 		apbh@80000000 {
 			pinctrl@80018000 {
-				pinctrl-names = "default", "default";
-				pinctrl-1 = <&hog_pins_cfa10049
-					&hog_pins_cfa10049_pullup>;
-
-				hog_pins_cfa10049: hog-10049@0 {
+				usb_pins_cfa10049: usb-10049@0 {
 					reg = <0>;
 					fsl,pinmux-ids = <
 						0x0073 /* MX28_PAD_GPMI_D7__GPIO_0_7 */
+					>;
+					fsl,drive-strength = <0>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <0>;
+				};
+
+				i2cmux_pins_cfa10049: i2cmux-10049@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
 						0x1163 /* MX28_PAD_LCD_D22__GPIO_1_22 */
 						0x1173 /* MX28_PAD_LCD_D22__GPIO_1_23 */
+					>;
+					fsl,drive-strength = <0>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <0>;
+				};
+
+				mac0_pins_cfa10049: mac0-10049@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
 						0x2153 /* MX28_PAD_SSP2_D5__GPIO_2_21 */
-						0x3053 /* MX28_PAD_AUART1_TX__GPIO_3_5 */
 					>;
 					fsl,drive-strength = <0>;
 					fsl,voltage = <1>;
 					fsl,pull-up = <0>;
 				};
 
-				hog_pins_cfa10049_pullup: hog-10049-pullup@0 {
+				pca_pins_cfa10049: pca-10049@0 {
 					reg = <0>;
 					fsl,pinmux-ids = <
 						0x2133 /* MX28_PAD_SSP2_D3__GPIO_2_19 */
+					>;
+					fsl,drive-strength = <0>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <1>;
+				};
+
+				rotary_pins_cfa10049: rotary-10049@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
 						0x3183 /* MX28_PAD_I2C0_SCL__GPIO_3_24 */
 						0x3193 /* MX28_PAD_I2C0_SDA__GPIO_3_25 */
+					>;
+					fsl,drive-strength = <0>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <1>;
+				};
+
+				rotary_btn_pins_cfa10049: rotary-btn-10049@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
 						0x31a3 /* MX28_PAD_SAIF_SDATA0__GPIO_3_26 */
-						0x31e3 /* MX28_PAD_LCD_RESET__GPIO_3_30 */
 					>;
 					fsl,drive-strength = <0>;
 					fsl,voltage = <1>;
@@ -60,6 +90,7 @@
 						0x2103 /* MX28_PAD_SSP2_SCK__GPIO_2_16 */
 						0x2113 /* MX28_PAD_SSP2_CMD__GPIO_2_17 */
 						0x2123 /* MX28_PAD_SSP2_D0__GPIO_2_18 */
+						0x3053 /* MX28_PAD_AUART1_TX__GPIO_3_5 */
 					>;
 					fsl,drive-strength = <1>;
 					fsl,voltage = <1>;
@@ -120,6 +151,16 @@
 					fsl,pull-up = <0>;
 				};
 
+				lcdif_pins_cfa10049_pullup: lcdif-10049-pullup@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						0x31e3 /* MX28_PAD_LCD_RESET__GPIO_3_30 */
+					>;
+					fsl,drive-strength = <0>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <1>;
+				};
+
 				w1_gpio_pins: w1-gpio@0 {
 					reg = <0>;
 					fsl,pinmux-ids = <
@@ -134,7 +175,8 @@
 			lcdif@80030000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&lcdif_18bit_pins_cfa10049
-					     &lcdif_pins_cfa10049>;
+					     &lcdif_pins_cfa10049
+					     &lcdif_pins_cfa10049_pullup>;
 				display = <&display>;
 				status = "okay";
 
@@ -181,6 +223,8 @@
 				compatible = "i2c-mux-gpio";
 				#address-cells = <1>;
 				#size-cells = <0>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&i2cmux_pins_cfa10049>;
 				mux-gpios = <&gpio1 22 0 &gpio1 23 0>;
 				i2c-parent = <&i2c1>;
 
@@ -203,6 +247,8 @@
 
 					pca9555: pca9555@20 {
 						compatible = "nxp,pca9555";
+						pinctrl-names = "default";
+						pinctrl-0 = <&pca_pins_cfa10049>;
 						interrupt-parent = <&gpio2>;
 						interrupts = <19 0x2>;
 						gpio-controller;
@@ -239,6 +285,8 @@
 
 		reg_usb1_vbus: usb1_vbus {
 			compatible = "regulator-fixed";
+			pinctrl-names = "default";
+			pinctrl-0 = <&usb_pins_cfa10049>;
 			regulator-name = "usb1_vbus";
 			regulator-min-microvolt = <5000000>;
 			regulator-max-microvolt = <5000000>;
@@ -250,7 +298,8 @@
 		mac0: ethernet@800f0000 {
 			phy-mode = "rmii";
 			pinctrl-names = "default";
-			pinctrl-0 = <&mac0_pins_a>;
+			pinctrl-0 = <&mac0_pins_a
+				&mac0_pins_cfa10049>;
 			phy-reset-gpios = <&gpio2 21 0>;
 			phy-reset-duration = <100>;
 			status = "okay";
@@ -320,6 +369,8 @@
 
 	gpio_keys {
 		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&rotary_btn_pins_cfa10049>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 
@@ -333,6 +384,8 @@
 
 	rotary {
 		compatible = "rotary-encoder";
+		pinctrl-names = "default";
+		pinctrl-0 = <&rotary_pins_cfa10049>;
 		gpios = <&gpio3 24 1>, <&gpio3 25 1>;
 		linux,axis = <1>; /* REL_Y */
 		rotary-encoder,relative-axis;
-- 
1.8.1.2

[PATCHv4 6/8] ARM: mxs: dt: cfa10055: make hogpins grabbed by respective drivers

[Alexandre Belloni]

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
 arch/arm/boot/dts/imx28-cfa10055.dts | 38 ++++++++++++------------------------
 1 file changed, 13 insertions(+), 25 deletions(-)

diff --git a/arch/arm/boot/dts/imx28-cfa10055.dts b/arch/arm/boot/dts/imx28-cfa10055.dts
index 1581112..171bcbe 100644
--- a/arch/arm/boot/dts/imx28-cfa10055.dts
+++ b/arch/arm/boot/dts/imx28-cfa10055.dts
@@ -23,36 +23,13 @@
 	apb at 80000000 {
 		apbh at 80000000 {
 			pinctrl at 80018000 {
-				pinctrl-names = "default", "default";
-				pinctrl-1 = <&hog_pins_cfa10055
-					&hog_pins_cfa10055_pullup>;
-
-				hog_pins_cfa10055: hog-10055 at 0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						0x3053 /* MX28_PAD_AUART1_TX__GPIO_3_5 */
-					>;
-					fsl,drive-strength = <0>;
-					fsl,voltage = <1>;
-					fsl,pull-up = <0>;
-				};
-
-				hog_pins_cfa10055_pullup: hog-10055-pullup at 0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						0x31e3 /* MX28_PAD_LCD_RESET__GPIO_3_30 */
-					>;
-					fsl,drive-strength = <0>;
-					fsl,voltage = <1>;
-					fsl,pull-up = <1>;
-				};
-
 				spi2_pins_cfa10055: spi2-cfa10055 at 0 {
 					reg = <0>;
 					fsl,pinmux-ids = <
 						0x2103 /* MX28_PAD_SSP2_SCK__GPIO_2_16 */
 						0x2113 /* MX28_PAD_SSP2_CMD__GPIO_2_17 */
 						0x2123 /* MX28_PAD_SSP2_D0__GPIO_2_18 */
+						0x3053 /* MX28_PAD_AUART1_TX__GPIO_3_5 */
 					>;
 					fsl,drive-strength = <1>;
 					fsl,voltage = <1>;
@@ -98,12 +75,23 @@
 					fsl,voltage = <1>;
 					fsl,pull-up = <0>;
 				};
+
+				lcdif_pins_cfa10055_pullup: lcdif-10055-pullup at 0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						0x31e3 /* MX28_PAD_LCD_RESET__GPIO_3_30 */
+					>;
+					fsl,drive-strength = <0>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <1>;
+				};
 			};
 
 			lcdif at 80030000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&lcdif_18bit_pins_cfa10055
-					     &lcdif_pins_cfa10055>;
+					     &lcdif_pins_cfa10055
+					     &lcdif_pins_cfa10055_pullup>;
 				display = <&display>;
 				status = "okay";
 
-- 
1.8.1.2

[PATCHv4 6/8] ARM: mxs: dt: cfa10055: make hogpins grabbed by respective drivers

[Alexandre Belloni]

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
 arch/arm/boot/dts/imx28-cfa10055.dts | 38 ++++++++++++------------------------
 1 file changed, 13 insertions(+), 25 deletions(-)

diff --git a/arch/arm/boot/dts/imx28-cfa10055.dts b/arch/arm/boot/dts/imx28-cfa10055.dts
index 1581112..171bcbe 100644
--- a/arch/arm/boot/dts/imx28-cfa10055.dts
+++ b/arch/arm/boot/dts/imx28-cfa10055.dts
@@ -23,36 +23,13 @@
 	apb@80000000 {
 		apbh@80000000 {
 			pinctrl@80018000 {
-				pinctrl-names = "default", "default";
-				pinctrl-1 = <&hog_pins_cfa10055
-					&hog_pins_cfa10055_pullup>;
-
-				hog_pins_cfa10055: hog-10055@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						0x3053 /* MX28_PAD_AUART1_TX__GPIO_3_5 */
-					>;
-					fsl,drive-strength = <0>;
-					fsl,voltage = <1>;
-					fsl,pull-up = <0>;
-				};
-
-				hog_pins_cfa10055_pullup: hog-10055-pullup@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						0x31e3 /* MX28_PAD_LCD_RESET__GPIO_3_30 */
-					>;
-					fsl,drive-strength = <0>;
-					fsl,voltage = <1>;
-					fsl,pull-up = <1>;
-				};
-
 				spi2_pins_cfa10055: spi2-cfa10055@0 {
 					reg = <0>;
 					fsl,pinmux-ids = <
 						0x2103 /* MX28_PAD_SSP2_SCK__GPIO_2_16 */
 						0x2113 /* MX28_PAD_SSP2_CMD__GPIO_2_17 */
 						0x2123 /* MX28_PAD_SSP2_D0__GPIO_2_18 */
+						0x3053 /* MX28_PAD_AUART1_TX__GPIO_3_5 */
 					>;
 					fsl,drive-strength = <1>;
 					fsl,voltage = <1>;
@@ -98,12 +75,23 @@
 					fsl,voltage = <1>;
 					fsl,pull-up = <0>;
 				};
+
+				lcdif_pins_cfa10055_pullup: lcdif-10055-pullup@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						0x31e3 /* MX28_PAD_LCD_RESET__GPIO_3_30 */
+					>;
+					fsl,drive-strength = <0>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <1>;
+				};
 			};
 
 			lcdif@80030000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&lcdif_18bit_pins_cfa10055
-					     &lcdif_pins_cfa10055>;
+					     &lcdif_pins_cfa10055
+					     &lcdif_pins_cfa10055_pullup>;
 				display = <&display>;
 				status = "okay";
 
-- 
1.8.1.2

[PATCHv4 7/8] ARM: mxs: dt: cfa10057: remove hogpins

[Alexandre Belloni]

Necessary pins are now grabbed by respective drivers. Unecessary hogpins are
simply removed.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
 arch/arm/boot/dts/imx28-cfa10057.dts | 23 +++--------------------
 1 file changed, 3 insertions(+), 20 deletions(-)

diff --git a/arch/arm/boot/dts/imx28-cfa10057.dts b/arch/arm/boot/dts/imx28-cfa10057.dts
index 2da713c..0333c05 100644
--- a/arch/arm/boot/dts/imx28-cfa10057.dts
+++ b/arch/arm/boot/dts/imx28-cfa10057.dts
@@ -23,35 +23,16 @@
 	apb at 80000000 {
 		apbh at 80000000 {
 			pinctrl at 80018000 {
-				pinctrl-names = "default", "default";
-				pinctrl-1 = <&hog_pins_cfa10057
-					&hog_pins_cfa10057_pullup>;
-
-				hog_pins_cfa10057: hog-10057 at 0 {
+				usb_pins_cfa10057: usb-10057 at 0 {
 					reg = <0>;
 					fsl,pinmux-ids = <
 						0x0073 /* MX28_PAD_GPMI_D7__GPIO_0_7 */
-						0x3053 /* MX28_PAD_AUART1_TX__GPIO_3_5 */
 					>;
 					fsl,drive-strength = <0>;
 					fsl,voltage = <1>;
 					fsl,pull-up = <0>;
 				};
 
-				hog_pins_cfa10057_pullup: hog-10057-pullup at 0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						0x2133 /* MX28_PAD_SSP2_D3__GPIO_2_19 */
-						0x3183 /* MX28_PAD_I2C0_SCL__GPIO_3_24 */
-						0x3193 /* MX28_PAD_I2C0_SDA__GPIO_3_25 */
-						0x31a3 /* MX28_PAD_SAIF_SDATA0__GPIO_3_26 */
-						0x31e3 /* MX28_PAD_LCD_RESET__GPIO_3_30 */
-					>;
-					fsl,drive-strength = <0>;
-					fsl,voltage = <1>;
-					fsl,pull-up = <1>;
-				};
-
 				lcdif_18bit_pins_cfa10057: lcdif-18bit at 0 {
 					reg = <0>;
 					fsl,pinmux-ids = <
@@ -164,6 +145,8 @@
 
 		reg_usb1_vbus: usb1_vbus {
 			compatible = "regulator-fixed";
+			pinctrl-names = "default";
+			pinctrl-0 = <&usb_pins_cfa10057>;
 			regulator-name = "usb1_vbus";
 			regulator-min-microvolt = <5000000>;
 			regulator-max-microvolt = <5000000>;
-- 
1.8.1.2

[PATCHv4 7/8] ARM: mxs: dt: cfa10057: remove hogpins

[Alexandre Belloni]

Necessary pins are now grabbed by respective drivers. Unecessary hogpins are
simply removed.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
 arch/arm/boot/dts/imx28-cfa10057.dts | 23 +++--------------------
 1 file changed, 3 insertions(+), 20 deletions(-)

diff --git a/arch/arm/boot/dts/imx28-cfa10057.dts b/arch/arm/boot/dts/imx28-cfa10057.dts
index 2da713c..0333c05 100644
--- a/arch/arm/boot/dts/imx28-cfa10057.dts
+++ b/arch/arm/boot/dts/imx28-cfa10057.dts
@@ -23,35 +23,16 @@
 	apb@80000000 {
 		apbh@80000000 {
 			pinctrl@80018000 {
-				pinctrl-names = "default", "default";
-				pinctrl-1 = <&hog_pins_cfa10057
-					&hog_pins_cfa10057_pullup>;
-
-				hog_pins_cfa10057: hog-10057@0 {
+				usb_pins_cfa10057: usb-10057@0 {
 					reg = <0>;
 					fsl,pinmux-ids = <
 						0x0073 /* MX28_PAD_GPMI_D7__GPIO_0_7 */
-						0x3053 /* MX28_PAD_AUART1_TX__GPIO_3_5 */
 					>;
 					fsl,drive-strength = <0>;
 					fsl,voltage = <1>;
 					fsl,pull-up = <0>;
 				};
 
-				hog_pins_cfa10057_pullup: hog-10057-pullup@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						0x2133 /* MX28_PAD_SSP2_D3__GPIO_2_19 */
-						0x3183 /* MX28_PAD_I2C0_SCL__GPIO_3_24 */
-						0x3193 /* MX28_PAD_I2C0_SDA__GPIO_3_25 */
-						0x31a3 /* MX28_PAD_SAIF_SDATA0__GPIO_3_26 */
-						0x31e3 /* MX28_PAD_LCD_RESET__GPIO_3_30 */
-					>;
-					fsl,drive-strength = <0>;
-					fsl,voltage = <1>;
-					fsl,pull-up = <1>;
-				};
-
 				lcdif_18bit_pins_cfa10057: lcdif-18bit@0 {
 					reg = <0>;
 					fsl,pinmux-ids = <
@@ -164,6 +145,8 @@
 
 		reg_usb1_vbus: usb1_vbus {
 			compatible = "regulator-fixed";
+			pinctrl-names = "default";
+			pinctrl-0 = <&usb_pins_cfa10057>;
 			regulator-name = "usb1_vbus";
 			regulator-min-microvolt = <5000000>;
 			regulator-max-microvolt = <5000000>;
-- 
1.8.1.2

[PATCHv4 8/8] ARM: mxs: dt: cfa10036: make hogpins grabbed by respective drivers

[Alexandre Belloni]

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
 arch/arm/boot/dts/imx28-cfa10036.dts | 7 +++----
 1 file changed, 3 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/imx28-cfa10036.dts b/arch/arm/boot/dts/imx28-cfa10036.dts
index 94c4476..1ec8c94 100644
--- a/arch/arm/boot/dts/imx28-cfa10036.dts
+++ b/arch/arm/boot/dts/imx28-cfa10036.dts
@@ -23,10 +23,7 @@
 	apb at 80000000 {
 		apbh at 80000000 {
 			pinctrl at 80018000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&hog_pins_cfa10036>;
-
-				hog_pins_cfa10036: hog-10036 at 0 {
+				ssd1306_cfa10036: ssd1306-10036 at 0 {
 					reg = <0>;
 					fsl,pinmux-ids = <
 						0x2073 /* MX28_PAD_SSP0_D7__GPIO_2_7 */
@@ -83,6 +80,8 @@
 
 				ssd1306: oled@3c {
 					compatible = "solomon,ssd1306fb-i2c";
+					pinctrl-names = "default";
+					pinctrl-0 = <&ssd1306_cfa10036>;
 					reg = <0x3c>;
 					reset-gpios = <&gpio2 7 0>;
 					solomon,height = <32>;
-- 
1.8.1.2

[PATCHv4 8/8] ARM: mxs: dt: cfa10036: make hogpins grabbed by respective drivers

[Alexandre Belloni]

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
 arch/arm/boot/dts/imx28-cfa10036.dts | 7 +++----
 1 file changed, 3 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/imx28-cfa10036.dts b/arch/arm/boot/dts/imx28-cfa10036.dts
index 94c4476..1ec8c94 100644
--- a/arch/arm/boot/dts/imx28-cfa10036.dts
+++ b/arch/arm/boot/dts/imx28-cfa10036.dts
@@ -23,10 +23,7 @@
 	apb@80000000 {
 		apbh@80000000 {
 			pinctrl@80018000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&hog_pins_cfa10036>;
-
-				hog_pins_cfa10036: hog-10036@0 {
+				ssd1306_cfa10036: ssd1306-10036@0 {
 					reg = <0>;
 					fsl,pinmux-ids = <
 						0x2073 /* MX28_PAD_SSP0_D7__GPIO_2_7 */
@@ -83,6 +80,8 @@
 
 				ssd1306: oled@3c {
 					compatible = "solomon,ssd1306fb-i2c";
+					pinctrl-names = "default";
+					pinctrl-0 = <&ssd1306_cfa10036>;
 					reg = <0x3c>;
 					reset-gpios = <&gpio2 7 0>;
 					solomon,height = <32>;
-- 
1.8.1.2

[PATCHv4 2/8] ARM: mxs: dt: Add Crystalfontz CFA-10056 device tree

[Maxime Ripard]

On Mon, Jul 01, 2013 at 03:23:23PM +0200, Alexandre Belloni wrote:
> From: Brian Lilly <brian@crystalfontz.com>
> 
> The CFA-10056 is a breakout board for the CFA-10036, and is
> basically a CFA-10037, with a 4.3" screen.
> 
> Signed-off-by: Brian Lilly <brian@crystalfontz.com>
> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 836 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20130701/042dafb4/attachment.sig>

Re: [PATCHv4 2/8] ARM: mxs: dt: Add Crystalfontz CFA-10056 device tree

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 536 bytes --]

On Mon, Jul 01, 2013 at 03:23:23PM +0200, Alexandre Belloni wrote:
> From: Brian Lilly <brian@crystalfontz.com>
> 
> The CFA-10056 is a breakout board for the CFA-10036, and is
> basically a CFA-10037, with a 4.3" screen.
> 
> Signed-off-by: Brian Lilly <brian@crystalfontz.com>
> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 836 bytes --]

[PATCHv4 0/8] ARM: mxs: Various Crystalfontz DT additions

[Shawn Guo]

On Mon, Jul 01, 2013 at 03:23:21PM +0200, Alexandre Belloni wrote:
> Alexandre Belloni (6):
>   ARM: mxs: Simplify detection of CrystalFontz boards
>   ARM: mxs: dt: cfa10037: make hogpins grabbed by respective drivers
>   ARM: mxs: dt: cfa10049: make hogpins grabbed by respective drivers
>   ARM: mxs: dt: cfa10055: make hogpins grabbed by respective drivers
>   ARM: mxs: dt: cfa10057: remove hogpins
>   ARM: mxs: dt: cfa10036: make hogpins grabbed by respective drivers
> 
> Brian Lilly (2):
>   ARM: mxs: dt: Add Crystalfontz CFA-10056 device tree
>   ARM: mxs: dt: Add Crystalfontz CFA-10058 device tree

All applied, thanks.

Shawn

Re: [PATCHv4 0/8] ARM: mxs: Various Crystalfontz DT additions

[Shawn Guo]

On Mon, Jul 01, 2013 at 03:23:21PM +0200, Alexandre Belloni wrote:
> Alexandre Belloni (6):
>   ARM: mxs: Simplify detection of CrystalFontz boards
>   ARM: mxs: dt: cfa10037: make hogpins grabbed by respective drivers
>   ARM: mxs: dt: cfa10049: make hogpins grabbed by respective drivers
>   ARM: mxs: dt: cfa10055: make hogpins grabbed by respective drivers
>   ARM: mxs: dt: cfa10057: remove hogpins
>   ARM: mxs: dt: cfa10036: make hogpins grabbed by respective drivers
> 
> Brian Lilly (2):
>   ARM: mxs: dt: Add Crystalfontz CFA-10056 device tree
>   ARM: mxs: dt: Add Crystalfontz CFA-10058 device tree

All applied, thanks.

Shawn