* Booting failed
@ 2014-05-08 10:15 deepak vijay
2014-05-09 10:31 ` deepak vijay
0 siblings, 1 reply; 3+ messages in thread
From: deepak vijay @ 2014-05-08 10:15 UTC (permalink / raw)
To: meta-ti
[-- Attachment #1: Type: text/plain, Size: 1381 bytes --]
Hi,
I have build omap3evm images by including mata-ti layer.
When I am trying to boot the omap3evm board it is stuck at "Uncompressing
Linux... done, booting the kernel" this comment.
Can any one help me to over come this issue.
The boot logs are given below.
U-Boot SPL 2011.12 (May 08 2014 - 15:01:46)
Texas Instruments Revision detection unimplemented
OMAP SD/MMC: 0
reading u-boot.img
reading u-boot.img
U-Boot 2011.12 (May 08 2014 - 15:01:46)
OMAP36XX/37XX-GP ES1.2, CPU-OPP2, L3-165MHz, Max CPU Clock 1 Ghz
OMAP3 EVM board + LPDDR/NAND
I2C: ready
DRAM: 256 MiB
NAND: 512 MiB
MMC: OMAP SD/MMC: 0
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Read back SMSC id 0x92200000
Die ID #706a00029ff80000016842c911024007
Net: smc911x-0
Hit any key to stop autoboot: 0
reading boot.scr
** Unable to read "boot.scr" from mmc 0:1 **
reading uImage
3139340 bytes read
Booting from mmc ...
## Booting kernel from Legacy Image at 82000000 ...
Image Name: Linux-2.6.37
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3139276 Bytes = 3 MiB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
Regards,
Deepak Vijay
[-- Attachment #2: Type: text/html, Size: 1987 bytes --]
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: Booting failed
2014-05-08 10:15 Booting failed deepak vijay
@ 2014-05-09 10:31 ` deepak vijay
2014-05-09 18:58 ` Denys Dmytriyenko
0 siblings, 1 reply; 3+ messages in thread
From: deepak vijay @ 2014-05-09 10:31 UTC (permalink / raw)
To: meta-ti
[-- Attachment #1: Type: text/plain, Size: 8500 bytes --]
Hi,
When I configured Low level debugging and earlyprintk in bootargs I am
getting the following output logs of crashing.
U-Boot SPL 2011.12 (May 08 2014 - 15:01:46)
Texas Instruments Revision detection unimplemented
OMAP SD/MMC: 0
reading u-boot.img
reading u-boot.img
U-Boot 2011.12 (May 08 2014 - 15:01:46)
OMAP36XX/37XX-GP ES1.2, CPU-OPP2, L3-165MHz, Max CPU Clock 1 Ghz
OMAP3 EVM board + LPDDR/NAND
I2C: ready
DRAM: 256 MiB
NAND: 512 MiB
MMC: OMAP SD/MMC: 0
In: serial
Out: serial
Err: serial
Read back SMSC id 0x92200000
Die ID #706a00029ff80000016842c911024007
Net: smc911x-0
Hit any key to stop autoboot: 0
reading boot.scr
** Unable to read "boot.scr" from mmc 0:1 **
reading uImage
3214968 bytes read
Booting from mmc ...
## Booting kernel from Legacy Image at 82000000 ...
Image Name: Linux-2.6.37
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3214904 Bytes = 3.1 MiB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
********Using machid 0x5ff from environment
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Linux version 2.6.37 (mistral@CPU000512U) (gcc version 4.8.2
(GCC) ) #2 Fri May 9 14:42:06
IST 2014
[ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7),
cr=10c53c7d
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT aliasing instruction
cache
[ 0.000000] Machine: OMAP3 EVM
[ 0.000000] bootconsole [earlycon0] enabled
[ 0.000000] Reserving 4194304 bytes SDRAM for VRAM
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] OMAP3630 ES1.2 (l2cache iva sgx neon isp 192mhz_clk )
[ 0.000000] SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x10000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 64000
[ 0.000000] Kernel command line: console=ttyO0,115200n8 earlyprintk
root=/dev/mmcblk0p2 rw rootfstype=
ext3 rootwait
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072
bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 252MB = 252MB total
[ 0.000000] Memory: 242156k/242156k available, 19988k reserved, 0K
highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
[ 0.000000] vmalloc : 0xd0800000 - 0xf8000000 ( 632 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .init : 0xc0008000 - 0xc003c000 ( 208 kB)
[ 0.000000] .text : 0xc003c000 - 0xc05eda00 (5831 kB)
[ 0.000000] .data : 0xc05ee000 - 0xc07afb60 (1799 kB)
[ 0.000000] Unable to handle kernel paging request at virtual address
8002f130
[ 0.000000] pgd = c0004000
[ 0.000000] [8002f130] *pgd=00000000
[ 0.000000] Internal error: Oops: 805 [#1]
[ 0.000000] last sysfs file:
[ 0.000000] Modules linked in:
[ 0.000000] CPU: 0 Not tainted (2.6.37 #2)
[ 0.000000] PC is at perf_pmu_register+0x12c/0x178
[ 0.000000] LR is at lockdep_init_map+0xb0/0x448
[ 0.000000] pc : [<c00ca3e4>] lr : [<c009bcd0>] psr: a00001d3
[ 0.000000] sp : c05eff90 ip : 00000000 fp : c05effd4
[ 0.000000] r10: 0000001f r9 : 413fc082 r8 : 000003f8
[ 0.000000] r7 : c0605750 r6 : c05eff68 r5 : c0f4b010 r4 : c05eff68
[ 0.000000] r3 : 8002f12c r2 : c07789dc r1 : c0548676 r0 : 00000001
[ 0.000000] Flags: NzCv IRQs off FIQs off Mode SVC_32 ISA ARM
Segment kernel
[ 0.000000] Control: 10c5387d Table: 80004019 DAC: 00000017
[ 0.000000] Process swapper (pid: 0, stack limit = 0xc05ee2f0)
[ 0.000000] Stack: (0xc05eff90 to 0xc05f0000)
[ 0.000000] ff80: c0778ba0 c07b0c40
c07b0c40 c0018588
[ 0.000000] ffa0: c05ee000 c0015784 3b9aca00 00000000 00000000 00000001
c0030bb0 c07afb80
[ 0.000000] ffc0: c0030bb0 c0f49100 c05f2d0c 8002f12c 00000000 c0008a0c
c000866c 000005ff
[ 0.000000] ffe0: 80000100 c0030bb0 10c53c7d c07afd34 c0030bac 80008034
00000000 00000000
[ 0.000000] [<c00ca3e4>] (perf_pmu_register+0x12c/0x178) from
[<c0018588>] (perf_event_init+0x3c/0xa4)
[ 0.000000] [<c0018588>] (perf_event_init+0x3c/0xa4) from [<c0015784>]
(sched_init+0x200/0x24c)
[ 0.000000] [<c0015784>] (sched_init+0x200/0x24c) from [<c0008a0c>]
(start_kernel+0x124/0x2d0)
[ 0.000000] [<c0008a0c>] (start_kernel+0x124/0x2d0) from [<80008034>]
(0x80008034)
[ 0.000000] Code: e59f204c e5843000 e5842004 e2422064 (e5834004)
[ 0.000000] irq 56, desc: c0769a24, depth: 1, count: 0, unhandled: 0
[ 0.000000] ->handle_irq(): c00adad0, handle_bad_irq+0x0/0x224
[ 0.000000] ->irq_data.chip(): (null), 0x0
[ 0.000000] ->action(): (null)
[ 0.000000] IRQ_DISABLED set
[ 0.000000] IRQ_NOPROBE set
[ 0.000000] IRQ_NOREQUEST set
[ 0.000000] Unable to handle kernel NULL pointer dereference at virtual
address 00000000
[ 0.000000] pgd = c0004000
[ 0.000000] [00000000] *pgd=00000000
[ 0.000000] Internal error: Oops: 5 [#2]
[ 0.000000] last sysfs file:
[ 0.000000] Modules linked in:
[ 0.000000] CPU: 0 Tainted: G D (2.6.37 #2)
[ 0.000000] PC is at handle_bad_irq+0x1a0/0x224
[ 0.000000] LR is at handle_bad_irq+0x184/0x224
[ 0.000000] pc : [<c00adc70>] lr : [<c00adc54>] psr: 400001d3
[ 0.000000] sp : c05efd28 ip : ffffffff fp : c00ca3e4
[ 0.000000] r10: 00000017 r9 : 00000000 r8 : c05ee000
[ 0.000000] r7 : c00ca3e6 r6 : 00000000 r5 : c078114c r4 : c0769a24
[ 0.000000] r3 : 00000000 r2 : 00000000 r1 : c05efc40 r0 : 00000025
[ 0.000000] Flags: nZcv IRQs off FIQs off Mode SVC_32 ISA ARM
Segment kernel
[ 0.000000] Control: 10c5387d Table: 80004019 DAC: 00000017
[ 0.000000] Process swapper (pid: 0, stack limit = 0xc05ee2f0)
[ 0.000000] Stack: (0xc05efd28 to 0xc05f0000)
[ 0.000000] fd20: 00000000 00000000 00000038 c003c070
ffffffff fa200000
[ 0.000000] fd40: 00000001 c043c6b8 c043bee4 c05efd70 00000000 00000001
c05f2f30 c05efdda
[ 0.000000] fd60: 00000001 c00ca3e6 c05ee000 00000000 00000017 c00ca3e4
ffffffff c05efd90
[ 0.000000] fd80: c043bee4 c043bee8 60000153 ffffffff c05eff48 c0049800
c05ee2f0 0000000b
[ 0.000000] fda0: 00000000 00000008 655f14a8 32663935 20633430 34383565
30303033 38356520
So from this I believe that it is because of kernel paging problem.
Please help me to resolve this.
Regards,
Deepak
On Thu, May 8, 2014 at 3:45 PM, deepak vijay <deepakvijay2255@rediff.com>wrote:
> Hi,
> I have build omap3evm images by including mata-ti layer.
> When I am trying to boot the omap3evm board it is stuck at "Uncompressing
> Linux... done, booting the kernel" this comment.
> Can any one help me to over come this issue.
> The boot logs are given below.
> U-Boot SPL 2011.12 (May 08 2014 - 15:01:46)
> Texas Instruments Revision detection unimplemented
> OMAP SD/MMC: 0
> reading u-boot.img
> reading u-boot.img
>
>
> U-Boot 2011.12 (May 08 2014 - 15:01:46)
>
> OMAP36XX/37XX-GP ES1.2, CPU-OPP2, L3-165MHz, Max CPU Clock 1 Ghz
> OMAP3 EVM board + LPDDR/NAND
> I2C: ready
> DRAM: 256 MiB
> NAND: 512 MiB
> MMC: OMAP SD/MMC: 0
> *** Warning - bad CRC, using default environment
>
> In: serial
> Out: serial
> Err: serial
> Read back SMSC id 0x92200000
> Die ID #706a00029ff80000016842c911024007
> Net: smc911x-0
> Hit any key to stop autoboot: 0
> reading boot.scr
>
> ** Unable to read "boot.scr" from mmc 0:1 **
> reading uImage
>
> 3139340 bytes read
> Booting from mmc ...
> ## Booting kernel from Legacy Image at 82000000 ...
> Image Name: Linux-2.6.37
> Image Type: ARM Linux Kernel Image (uncompressed)
> Data Size: 3139276 Bytes = 3 MiB
> Load Address: 80008000
> Entry Point: 80008000
> Verifying Checksum ... OK
> Loading Kernel Image ... OK
> OK
>
> Starting kernel ...
>
> Uncompressing Linux... done, booting the kernel.
>
>
> Regards,
> Deepak Vijay
>
[-- Attachment #2: Type: text/html, Size: 11127 bytes --]
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: Booting failed
2014-05-09 10:31 ` deepak vijay
@ 2014-05-09 18:58 ` Denys Dmytriyenko
0 siblings, 0 replies; 3+ messages in thread
From: Denys Dmytriyenko @ 2014-05-09 18:58 UTC (permalink / raw)
To: deepak vijay; +Cc: meta-ti
Well, you don't provide details, such as your configuration, build setup or
versions of your tools/layers, etc. You just say it rather vaguely:
> > I have build omap3evm images by including mata-ti layer.
From the bootlog it appears you used gcc-4.8 with such an old kernel 2.6.37.
I'm wondering if it's one of the incompatibilities between old kernels and new
toolchains, something like this one:
http://arago-project.org/git/?p=meta-ti.git;a=commitdiff;h=07809e70f4f277d894323b7d2ed39400e0cca8e3
The recommendation would be to use a correspondingly old toolchain, such as
gcc-4.5, if you really need to use such an old kernel 2.6.37.
Otherwise, OMAP3 should be well supported in recent mainline kernels, so if
you do not depend on specifically 2.6.37 kernel, you should consider using
that, in which case newer toolchains should also work.
--
Denys
On Fri, May 09, 2014 at 04:01:02PM +0530, deepak vijay wrote:
> Hi,
> When I configured Low level debugging and earlyprintk in bootargs I am
> getting the following output logs of crashing.
> U-Boot SPL 2011.12 (May 08 2014 - 15:01:46)
> Texas Instruments Revision detection unimplemented
> OMAP SD/MMC: 0
> reading u-boot.img
> reading u-boot.img
>
>
> U-Boot 2011.12 (May 08 2014 - 15:01:46)
>
> OMAP36XX/37XX-GP ES1.2, CPU-OPP2, L3-165MHz, Max CPU Clock 1 Ghz
> OMAP3 EVM board + LPDDR/NAND
> I2C: ready
> DRAM: 256 MiB
> NAND: 512 MiB
> MMC: OMAP SD/MMC: 0
> In: serial
> Out: serial
> Err: serial
> Read back SMSC id 0x92200000
> Die ID #706a00029ff80000016842c911024007
> Net: smc911x-0
> Hit any key to stop autoboot: 0
> reading boot.scr
>
> ** Unable to read "boot.scr" from mmc 0:1 **
> reading uImage
>
> 3214968 bytes read
> Booting from mmc ...
> ## Booting kernel from Legacy Image at 82000000 ...
> Image Name: Linux-2.6.37
> Image Type: ARM Linux Kernel Image (uncompressed)
> Data Size: 3214904 Bytes = 3.1 MiB
> Load Address: 80008000
> Entry Point: 80008000
> Verifying Checksum ... OK
> Loading Kernel Image ... OK
> OK
>
> Starting kernel ...
>
>
> ********Using machid 0x5ff from environment
> Uncompressing Linux... done, booting the kernel.
> [ 0.000000] Linux version 2.6.37 (mistral@CPU000512U) (gcc version 4.8.2
> (GCC) ) #2 Fri May 9 14:42:06
> IST 2014
> [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7),
> cr=10c53c7d
> [ 0.000000] CPU: VIPT nonaliasing data cache, VIPT aliasing instruction
> cache
> [ 0.000000] Machine: OMAP3 EVM
> [ 0.000000] bootconsole [earlycon0] enabled
> [ 0.000000] Reserving 4194304 bytes SDRAM for VRAM
> [ 0.000000] Memory policy: ECC disabled, Data cache writeback
> [ 0.000000] OMAP3630 ES1.2 (l2cache iva sgx neon isp 192mhz_clk )
> [ 0.000000] SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x10000
> [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
> Total pages: 64000
> [ 0.000000] Kernel command line: console=ttyO0,115200n8 earlyprintk
> root=/dev/mmcblk0p2 rw rootfstype=
> ext3 rootwait
> [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
> [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072
> bytes)
> [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
> [ 0.000000] Memory: 252MB = 252MB total
> [ 0.000000] Memory: 242156k/242156k available, 19988k reserved, 0K
> highmem
> [ 0.000000] Virtual kernel memory layout:
> [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
> [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
> [ 0.000000] DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
> [ 0.000000] vmalloc : 0xd0800000 - 0xf8000000 ( 632 MB)
> [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
> [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
> [ 0.000000] .init : 0xc0008000 - 0xc003c000 ( 208 kB)
> [ 0.000000] .text : 0xc003c000 - 0xc05eda00 (5831 kB)
> [ 0.000000] .data : 0xc05ee000 - 0xc07afb60 (1799 kB)
> [ 0.000000] Unable to handle kernel paging request at virtual address
> 8002f130
> [ 0.000000] pgd = c0004000
> [ 0.000000] [8002f130] *pgd=00000000
> [ 0.000000] Internal error: Oops: 805 [#1]
> [ 0.000000] last sysfs file:
> [ 0.000000] Modules linked in:
> [ 0.000000] CPU: 0 Not tainted (2.6.37 #2)
> [ 0.000000] PC is at perf_pmu_register+0x12c/0x178
> [ 0.000000] LR is at lockdep_init_map+0xb0/0x448
> [ 0.000000] pc : [<c00ca3e4>] lr : [<c009bcd0>] psr: a00001d3
> [ 0.000000] sp : c05eff90 ip : 00000000 fp : c05effd4
> [ 0.000000] r10: 0000001f r9 : 413fc082 r8 : 000003f8
> [ 0.000000] r7 : c0605750 r6 : c05eff68 r5 : c0f4b010 r4 : c05eff68
> [ 0.000000] r3 : 8002f12c r2 : c07789dc r1 : c0548676 r0 : 00000001
> [ 0.000000] Flags: NzCv IRQs off FIQs off Mode SVC_32 ISA ARM
> Segment kernel
> [ 0.000000] Control: 10c5387d Table: 80004019 DAC: 00000017
> [ 0.000000] Process swapper (pid: 0, stack limit = 0xc05ee2f0)
> [ 0.000000] Stack: (0xc05eff90 to 0xc05f0000)
> [ 0.000000] ff80: c0778ba0 c07b0c40
> c07b0c40 c0018588
> [ 0.000000] ffa0: c05ee000 c0015784 3b9aca00 00000000 00000000 00000001
> c0030bb0 c07afb80
> [ 0.000000] ffc0: c0030bb0 c0f49100 c05f2d0c 8002f12c 00000000 c0008a0c
> c000866c 000005ff
> [ 0.000000] ffe0: 80000100 c0030bb0 10c53c7d c07afd34 c0030bac 80008034
> 00000000 00000000
> [ 0.000000] [<c00ca3e4>] (perf_pmu_register+0x12c/0x178) from
> [<c0018588>] (perf_event_init+0x3c/0xa4)
> [ 0.000000] [<c0018588>] (perf_event_init+0x3c/0xa4) from [<c0015784>]
> (sched_init+0x200/0x24c)
> [ 0.000000] [<c0015784>] (sched_init+0x200/0x24c) from [<c0008a0c>]
> (start_kernel+0x124/0x2d0)
> [ 0.000000] [<c0008a0c>] (start_kernel+0x124/0x2d0) from [<80008034>]
> (0x80008034)
> [ 0.000000] Code: e59f204c e5843000 e5842004 e2422064 (e5834004)
> [ 0.000000] irq 56, desc: c0769a24, depth: 1, count: 0, unhandled: 0
> [ 0.000000] ->handle_irq(): c00adad0, handle_bad_irq+0x0/0x224
> [ 0.000000] ->irq_data.chip(): (null), 0x0
> [ 0.000000] ->action(): (null)
> [ 0.000000] IRQ_DISABLED set
> [ 0.000000] IRQ_NOPROBE set
> [ 0.000000] IRQ_NOREQUEST set
> [ 0.000000] Unable to handle kernel NULL pointer dereference at virtual
> address 00000000
> [ 0.000000] pgd = c0004000
> [ 0.000000] [00000000] *pgd=00000000
> [ 0.000000] Internal error: Oops: 5 [#2]
> [ 0.000000] last sysfs file:
> [ 0.000000] Modules linked in:
> [ 0.000000] CPU: 0 Tainted: G D (2.6.37 #2)
> [ 0.000000] PC is at handle_bad_irq+0x1a0/0x224
> [ 0.000000] LR is at handle_bad_irq+0x184/0x224
> [ 0.000000] pc : [<c00adc70>] lr : [<c00adc54>] psr: 400001d3
> [ 0.000000] sp : c05efd28 ip : ffffffff fp : c00ca3e4
> [ 0.000000] r10: 00000017 r9 : 00000000 r8 : c05ee000
> [ 0.000000] r7 : c00ca3e6 r6 : 00000000 r5 : c078114c r4 : c0769a24
> [ 0.000000] r3 : 00000000 r2 : 00000000 r1 : c05efc40 r0 : 00000025
> [ 0.000000] Flags: nZcv IRQs off FIQs off Mode SVC_32 ISA ARM
> Segment kernel
> [ 0.000000] Control: 10c5387d Table: 80004019 DAC: 00000017
> [ 0.000000] Process swapper (pid: 0, stack limit = 0xc05ee2f0)
> [ 0.000000] Stack: (0xc05efd28 to 0xc05f0000)
> [ 0.000000] fd20: 00000000 00000000 00000038 c003c070
> ffffffff fa200000
> [ 0.000000] fd40: 00000001 c043c6b8 c043bee4 c05efd70 00000000 00000001
> c05f2f30 c05efdda
> [ 0.000000] fd60: 00000001 c00ca3e6 c05ee000 00000000 00000017 c00ca3e4
> ffffffff c05efd90
> [ 0.000000] fd80: c043bee4 c043bee8 60000153 ffffffff c05eff48 c0049800
> c05ee2f0 0000000b
> [ 0.000000] fda0: 00000000 00000008 655f14a8 32663935 20633430 34383565
> 30303033 38356520
>
>
>
>
>
> So from this I believe that it is because of kernel paging problem.
> Please help me to resolve this.
>
>
> Regards,
> Deepak
>
>
> On Thu, May 8, 2014 at 3:45 PM, deepak vijay <deepakvijay2255@rediff.com>wrote:
>
> > Hi,
> > I have build omap3evm images by including mata-ti layer.
> > When I am trying to boot the omap3evm board it is stuck at "Uncompressing
> > Linux... done, booting the kernel" this comment.
> > Can any one help me to over come this issue.
> > The boot logs are given below.
> > U-Boot SPL 2011.12 (May 08 2014 - 15:01:46)
> > Texas Instruments Revision detection unimplemented
> > OMAP SD/MMC: 0
> > reading u-boot.img
> > reading u-boot.img
> >
> >
> > U-Boot 2011.12 (May 08 2014 - 15:01:46)
> >
> > OMAP36XX/37XX-GP ES1.2, CPU-OPP2, L3-165MHz, Max CPU Clock 1 Ghz
> > OMAP3 EVM board + LPDDR/NAND
> > I2C: ready
> > DRAM: 256 MiB
> > NAND: 512 MiB
> > MMC: OMAP SD/MMC: 0
> > *** Warning - bad CRC, using default environment
> >
> > In: serial
> > Out: serial
> > Err: serial
> > Read back SMSC id 0x92200000
> > Die ID #706a00029ff80000016842c911024007
> > Net: smc911x-0
> > Hit any key to stop autoboot: 0
> > reading boot.scr
> >
> > ** Unable to read "boot.scr" from mmc 0:1 **
> > reading uImage
> >
> > 3139340 bytes read
> > Booting from mmc ...
> > ## Booting kernel from Legacy Image at 82000000 ...
> > Image Name: Linux-2.6.37
> > Image Type: ARM Linux Kernel Image (uncompressed)
> > Data Size: 3139276 Bytes = 3 MiB
> > Load Address: 80008000
> > Entry Point: 80008000
> > Verifying Checksum ... OK
> > Loading Kernel Image ... OK
> > OK
> >
> > Starting kernel ...
> >
> > Uncompressing Linux... done, booting the kernel.
> >
> >
> > Regards,
> > Deepak Vijay
> >
> --
> _______________________________________________
> meta-ti mailing list
> meta-ti@yoctoproject.org
> https://lists.yoctoproject.org/listinfo/meta-ti
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2014-05-09 18:59 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2014-05-08 10:15 Booting failed deepak vijay
2014-05-09 10:31 ` deepak vijay
2014-05-09 18:58 ` Denys Dmytriyenko
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.