* [PATCH] wireless-regdb: add AUTO-BW rule flag @ 2014-05-09 8:38 ` Janusz Dziedzic 0 siblings, 0 replies; 13+ messages in thread From: Janusz Dziedzic @ 2014-05-09 8:38 UTC (permalink / raw) To: wireless-regdb; +Cc: linux-wireless, mcgrof, Janusz Dziedzic Sync with latest nl80211.h and add AUTO-BW flag. If this flag set, maximum available bandwidth should be calculated base on contiguous rules and wider channels will be allowed to cross multiple contiguous/overlapping frequency ranges. Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com> --- dbparse.py | 1 + 1 file changed, 1 insertion(+) diff --git a/dbparse.py b/dbparse.py index ac7234b..b735b6a 100755 --- a/dbparse.py +++ b/dbparse.py @@ -16,6 +16,7 @@ flag_definitions = { # hole at bit 8 # hole at bit 9. FIXME: Where is NO-HT40 defined? 'NO-HT40': 1<<10, + 'AUTO-BW': 1<<11, } dfs_regions = { -- 1.7.9.5 ^ permalink raw reply related [flat|nested] 13+ messages in thread
* [wireless-regdb] [PATCH] wireless-regdb: add AUTO-BW rule flag @ 2014-05-09 8:38 ` Janusz Dziedzic 0 siblings, 0 replies; 13+ messages in thread From: Janusz Dziedzic @ 2014-05-09 8:38 UTC (permalink / raw) To: wireless-regdb; +Cc: Janusz Dziedzic, linux-wireless, mcgrof Sync with latest nl80211.h and add AUTO-BW flag. If this flag set, maximum available bandwidth should be calculated base on contiguous rules and wider channels will be allowed to cross multiple contiguous/overlapping frequency ranges. Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com> --- dbparse.py | 1 + 1 file changed, 1 insertion(+) diff --git a/dbparse.py b/dbparse.py index ac7234b..b735b6a 100755 --- a/dbparse.py +++ b/dbparse.py @@ -16,6 +16,7 @@ flag_definitions = { # hole at bit 8 # hole at bit 9. FIXME: Where is NO-HT40 defined? 'NO-HT40': 1<<10, + 'AUTO-BW': 1<<11, } dfs_regions = { -- 1.7.9.5 _______________________________________________ wireless-regdb mailing list wireless-regdb@lists.infradead.org http://lists.infradead.org/mailman/listinfo/wireless-regdb ^ permalink raw reply related [flat|nested] 13+ messages in thread
* [PATCH 1/2] crda: sync with latest nl80211.h 2014-05-09 8:38 ` [wireless-regdb] " Janusz Dziedzic @ 2014-05-09 8:38 ` Janusz Dziedzic -1 siblings, 0 replies; 13+ messages in thread From: Janusz Dziedzic @ 2014-05-09 8:38 UTC (permalink / raw) To: wireless-regdb; +Cc: linux-wireless, mcgrof, Janusz Dziedzic Sync with latest nl80211.h wireless-testing. Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com> --- nl80211.h | 525 +++++++++++++++++++++++++++++++++++++++++++++++++++++++------ reglib.h | 3 - 2 files changed, 473 insertions(+), 55 deletions(-) diff --git a/nl80211.h b/nl80211.h index 79da871..1ba9d62 100644 --- a/nl80211.h +++ b/nl80211.h @@ -27,6 +27,8 @@ #include <linux/types.h> +#define NL80211_GENL_NAME "nl80211" + /** * DOC: Station handling * @@ -124,6 +126,31 @@ */ /** + * DOC: packet coalesce support + * + * In most cases, host that receives IPv4 and IPv6 multicast/broadcast + * packets does not do anything with these packets. Therefore the + * reception of these unwanted packets causes unnecessary processing + * and power consumption. + * + * Packet coalesce feature helps to reduce number of received interrupts + * to host by buffering these packets in firmware/hardware for some + * predefined time. Received interrupt will be generated when one of the + * following events occur. + * a) Expiration of hardware timer whose expiration time is set to maximum + * coalescing delay of matching coalesce rule. + * b) Coalescing buffer in hardware reaches it's limit. + * c) Packet doesn't match any of the configured coalesce rules. + * + * User needs to configure following parameters for creating a coalesce + * rule. + * a) Maximum coalescing delay + * b) List of packet patterns which needs to be matched + * c) Condition for coalescence. pattern 'match' or 'no match' + * Multiple such rules can be created. + */ + +/** * enum nl80211_commands - supported nl80211 commands * * @NL80211_CMD_UNSPEC: unspecified command to catch errors @@ -276,8 +303,9 @@ * passed, all channels allowed for the current regulatory domain * are used. Extra IEs can also be passed from the userspace by * using the %NL80211_ATTR_IE attribute. - * @NL80211_CMD_STOP_SCHED_SCAN: stop a scheduled scan. Returns -ENOENT - * if scheduled scan is not running. + * @NL80211_CMD_STOP_SCHED_SCAN: stop a scheduled scan. Returns -ENOENT if + * scheduled scan is not running. The caller may assume that as soon + * as the call returns, it is safe to start a new scheduled scan again. * @NL80211_CMD_SCHED_SCAN_RESULTS: indicates that there are scheduled scan * results available. * @NL80211_CMD_SCHED_SCAN_STOPPED: indicates that the scheduled scan has @@ -391,8 +419,18 @@ * %NL80211_ATTR_SSID attribute, and can optionally specify the association * IEs in %NL80211_ATTR_IE, %NL80211_ATTR_AUTH_TYPE, %NL80211_ATTR_USE_MFP, * %NL80211_ATTR_MAC, %NL80211_ATTR_WIPHY_FREQ, %NL80211_ATTR_CONTROL_PORT, - * %NL80211_ATTR_CONTROL_PORT_ETHERTYPE and - * %NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT. + * %NL80211_ATTR_CONTROL_PORT_ETHERTYPE, + * %NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT, %NL80211_ATTR_MAC_HINT, and + * %NL80211_ATTR_WIPHY_FREQ_HINT. + * If included, %NL80211_ATTR_MAC and %NL80211_ATTR_WIPHY_FREQ are + * restrictions on BSS selection, i.e., they effectively prevent roaming + * within the ESS. %NL80211_ATTR_MAC_HINT and %NL80211_ATTR_WIPHY_FREQ_HINT + * can be included to provide a recommendation of the initial BSS while + * allowing the driver to roam to other BSSes within the ESS and also to + * ignore this recommendation if the indicated BSS is not ideal. Only one + * set of BSSID,frequency parameters is used (i.e., either the enforcing + * %NL80211_ATTR_MAC,%NL80211_ATTR_WIPHY_FREQ or the less strict + * %NL80211_ATTR_MAC_HINT and %NL80211_ATTR_WIPHY_FREQ_HINT). * Background scan period can optionally be * specified in %NL80211_ATTR_BG_SCAN_PERIOD, * if not specified default background scan configuration @@ -554,7 +592,14 @@ * operation, %NL80211_ATTR_MAC contains the peer MAC address, and * %NL80211_ATTR_REASON_CODE the reason code to be used (only with * %NL80211_TDLS_TEARDOWN). - * @NL80211_CMD_TDLS_MGMT: Send a TDLS management frame. + * @NL80211_CMD_TDLS_MGMT: Send a TDLS management frame. The + * %NL80211_ATTR_TDLS_ACTION attribute determines the type of frame to be + * sent. Public Action codes (802.11-2012 8.1.5.1) will be sent as + * 802.11 management frames, while TDLS action codes (802.11-2012 + * 8.5.13.1) will be encapsulated and sent as data frames. The currently + * supported Public Action code is %WLAN_PUB_ACTION_TDLS_DISCOVER_RES + * and the currently supported TDLS actions codes are given in + * &enum ieee80211_tdls_actioncode. * * @NL80211_CMD_UNEXPECTED_FRAME: Used by an application controlling an AP * (or GO) interface (i.e. hostapd) to ask for unexpected frames to @@ -639,6 +684,41 @@ * with the relevant Information Elements. This event is used to report * received FT IEs (MDIE, FTIE, RSN IE, TIE, RICIE). * + * @NL80211_CMD_CRIT_PROTOCOL_START: Indicates user-space will start running + * a critical protocol that needs more reliability in the connection to + * complete. + * + * @NL80211_CMD_CRIT_PROTOCOL_STOP: Indicates the connection reliability can + * return back to normal. + * + * @NL80211_CMD_GET_COALESCE: Get currently supported coalesce rules. + * @NL80211_CMD_SET_COALESCE: Configure coalesce rules or clear existing rules. + * + * @NL80211_CMD_CHANNEL_SWITCH: Perform a channel switch by announcing the + * the new channel information (Channel Switch Announcement - CSA) + * in the beacon for some time (as defined in the + * %NL80211_ATTR_CH_SWITCH_COUNT parameter) and then change to the + * new channel. Userspace provides the new channel information (using + * %NL80211_ATTR_WIPHY_FREQ and the attributes determining channel + * width). %NL80211_ATTR_CH_SWITCH_BLOCK_TX may be supplied to inform + * other station that transmission must be blocked until the channel + * switch is complete. + * + * @NL80211_CMD_VENDOR: Vendor-specified command/event. The command is specified + * by the %NL80211_ATTR_VENDOR_ID attribute and a sub-command in + * %NL80211_ATTR_VENDOR_SUBCMD. Parameter(s) can be transported in + * %NL80211_ATTR_VENDOR_DATA. + * For feature advertisement, the %NL80211_ATTR_VENDOR_DATA attribute is + * used in the wiphy data as a nested attribute containing descriptions + * (&struct nl80211_vendor_cmd_info) of the supported vendor commands. + * This may also be sent as an event with the same attributes. + * + * @NL80211_CMD_SET_QOS_MAP: Set Interworking QoS mapping for IP DSCP values. + * The QoS mapping information is included in %NL80211_ATTR_QOS_MAP. If + * that attribute is not included, QoS mapping is disabled. Since this + * QoS mapping is relevant for IP packets, it is only valid during an + * association. This is cleared on disassociation and AP restart. + * * @NL80211_CMD_MAX: highest used command number * @__NL80211_CMD_AFTER_LAST: internal use */ @@ -798,6 +878,18 @@ enum nl80211_commands { NL80211_CMD_UPDATE_FT_IES, NL80211_CMD_FT_EVENT, + NL80211_CMD_CRIT_PROTOCOL_START, + NL80211_CMD_CRIT_PROTOCOL_STOP, + + NL80211_CMD_GET_COALESCE, + NL80211_CMD_SET_COALESCE, + + NL80211_CMD_CHANNEL_SWITCH, + + NL80211_CMD_VENDOR, + + NL80211_CMD_SET_QOS_MAP, + /* add new commands above here */ /* used to define NL80211_CMD_MAX below */ @@ -933,7 +1025,7 @@ enum nl80211_commands { * to query the CRDA to retrieve one regulatory domain. This attribute can * also be used by userspace to query the kernel for the currently set * regulatory domain. We chose an alpha2 as that is also used by the - * IEEE-802.11d country information element to identify a country. + * IEEE-802.11 country information element to identify a country. * Users can also simply ask the wireless core to set regulatory domain * to a specific alpha2. * @NL80211_ATTR_REG_RULES: a nested array of regulatory domain regulatory @@ -1414,6 +1506,79 @@ enum nl80211_commands { * @NL80211_ATTR_IE_RIC: Resource Information Container Information * Element * + * @NL80211_ATTR_CRIT_PROT_ID: critical protocol identifier requiring increased + * reliability, see &enum nl80211_crit_proto_id (u16). + * @NL80211_ATTR_MAX_CRIT_PROT_DURATION: duration in milliseconds in which + * the connection should have increased reliability (u16). + * + * @NL80211_ATTR_PEER_AID: Association ID for the peer TDLS station (u16). + * This is similar to @NL80211_ATTR_STA_AID but with a difference of being + * allowed to be used with the first @NL80211_CMD_SET_STATION command to + * update a TDLS peer STA entry. + * + * @NL80211_ATTR_COALESCE_RULE: Coalesce rule information. + * + * @NL80211_ATTR_CH_SWITCH_COUNT: u32 attribute specifying the number of TBTT's + * until the channel switch event. + * @NL80211_ATTR_CH_SWITCH_BLOCK_TX: flag attribute specifying that transmission + * must be blocked on the current channel (before the channel switch + * operation). + * @NL80211_ATTR_CSA_IES: Nested set of attributes containing the IE information + * for the time while performing a channel switch. + * @NL80211_ATTR_CSA_C_OFF_BEACON: Offset of the channel switch counter + * field in the beacons tail (%NL80211_ATTR_BEACON_TAIL). + * @NL80211_ATTR_CSA_C_OFF_PRESP: Offset of the channel switch counter + * field in the probe response (%NL80211_ATTR_PROBE_RESP). + * + * @NL80211_ATTR_RXMGMT_FLAGS: flags for nl80211_send_mgmt(), u32. + * As specified in the &enum nl80211_rxmgmt_flags. + * + * @NL80211_ATTR_STA_SUPPORTED_CHANNELS: array of supported channels. + * + * @NL80211_ATTR_STA_SUPPORTED_OPER_CLASSES: array of supported + * supported operating classes. + * + * @NL80211_ATTR_HANDLE_DFS: A flag indicating whether user space + * controls DFS operation in IBSS mode. If the flag is included in + * %NL80211_CMD_JOIN_IBSS request, the driver will allow use of DFS + * channels and reports radar events to userspace. Userspace is required + * to react to radar events, e.g. initiate a channel switch or leave the + * IBSS network. + * + * @NL80211_ATTR_SUPPORT_5_MHZ: A flag indicating that the device supports + * 5 MHz channel bandwidth. + * @NL80211_ATTR_SUPPORT_10_MHZ: A flag indicating that the device supports + * 10 MHz channel bandwidth. + * + * @NL80211_ATTR_OPMODE_NOTIF: Operating mode field from Operating Mode + * Notification Element based on association request when used with + * %NL80211_CMD_NEW_STATION; u8 attribute. + * + * @NL80211_ATTR_VENDOR_ID: The vendor ID, either a 24-bit OUI or, if + * %NL80211_VENDOR_ID_IS_LINUX is set, a special Linux ID (not used yet) + * @NL80211_ATTR_VENDOR_SUBCMD: vendor sub-command + * @NL80211_ATTR_VENDOR_DATA: data for the vendor command, if any; this + * attribute is also used for vendor command feature advertisement + * @NL80211_ATTR_VENDOR_EVENTS: used for event list advertising in the wiphy + * info, containing a nested array of possible events + * + * @NL80211_ATTR_QOS_MAP: IP DSCP mapping for Interworking QoS mapping. This + * data is in the format defined for the payload of the QoS Map Set element + * in IEEE Std 802.11-2012, 8.4.2.97. + * + * @NL80211_ATTR_MAC_HINT: MAC address recommendation as initial BSS + * @NL80211_ATTR_WIPHY_FREQ_HINT: frequency of the recommended initial BSS + * + * @NL80211_ATTR_MAX_AP_ASSOC_STA: Device attribute that indicates how many + * associated stations are supported in AP mode (including P2P GO); u32. + * Since drivers may not have a fixed limit on the maximum number (e.g., + * other concurrent operations may affect this), drivers are allowed to + * advertise values that cannot always be met. In such cases, an attempt + * to add a new station entry with @NL80211_CMD_NEW_STATION may fail. + * + * @NL80211_ATTR_TDLS_PEER_CAPABILITY: flags for TDLS peer capabilities, u32. + * As specified in the &enum nl80211_tdls_peer_capability. + * * @NL80211_ATTR_MAX: highest attribute number currently defined * @__NL80211_ATTR_AFTER_LAST: internal use */ @@ -1709,6 +1874,46 @@ enum nl80211_attrs { NL80211_ATTR_MDID, NL80211_ATTR_IE_RIC, + NL80211_ATTR_CRIT_PROT_ID, + NL80211_ATTR_MAX_CRIT_PROT_DURATION, + + NL80211_ATTR_PEER_AID, + + NL80211_ATTR_COALESCE_RULE, + + NL80211_ATTR_CH_SWITCH_COUNT, + NL80211_ATTR_CH_SWITCH_BLOCK_TX, + NL80211_ATTR_CSA_IES, + NL80211_ATTR_CSA_C_OFF_BEACON, + NL80211_ATTR_CSA_C_OFF_PRESP, + + NL80211_ATTR_RXMGMT_FLAGS, + + NL80211_ATTR_STA_SUPPORTED_CHANNELS, + + NL80211_ATTR_STA_SUPPORTED_OPER_CLASSES, + + NL80211_ATTR_HANDLE_DFS, + + NL80211_ATTR_SUPPORT_5_MHZ, + NL80211_ATTR_SUPPORT_10_MHZ, + + NL80211_ATTR_OPMODE_NOTIF, + + NL80211_ATTR_VENDOR_ID, + NL80211_ATTR_VENDOR_SUBCMD, + NL80211_ATTR_VENDOR_DATA, + NL80211_ATTR_VENDOR_EVENTS, + + NL80211_ATTR_QOS_MAP, + + NL80211_ATTR_MAC_HINT, + NL80211_ATTR_WIPHY_FREQ_HINT, + + NL80211_ATTR_MAX_AP_ASSOC_STA, + + NL80211_ATTR_TDLS_PEER_CAPABILITY, + /* add attributes here, update the policy in nl80211.c */ __NL80211_ATTR_AFTER_LAST, @@ -1973,6 +2178,10 @@ enum nl80211_sta_bss_param { * @NL80211_STA_INFO_PEER_PM: peer mesh STA link-specific power mode * @NL80211_STA_INFO_NONPEER_PM: neighbor mesh STA power save mode towards * non-peer STA + * @NL80211_STA_INFO_CHAIN_SIGNAL: per-chain signal strength of last PPDU + * Contains a nested array of signal strength attributes (u8, dBm) + * @NL80211_STA_INFO_CHAIN_SIGNAL_AVG: per-chain signal strength average + * Same format as NL80211_STA_INFO_CHAIN_SIGNAL. * @__NL80211_STA_INFO_AFTER_LAST: internal * @NL80211_STA_INFO_MAX: highest possible station info attribute */ @@ -2002,6 +2211,8 @@ enum nl80211_sta_info { NL80211_STA_INFO_NONPEER_PM, NL80211_STA_INFO_RX_BYTES64, NL80211_STA_INFO_TX_BYTES64, + NL80211_STA_INFO_CHAIN_SIGNAL, + NL80211_STA_INFO_CHAIN_SIGNAL_AVG, /* keep last */ __NL80211_STA_INFO_AFTER_LAST, @@ -2103,10 +2314,9 @@ enum nl80211_band_attr { * @NL80211_FREQUENCY_ATTR_FREQ: Frequency in MHz * @NL80211_FREQUENCY_ATTR_DISABLED: Channel is disabled in current * regulatory domain. - * @NL80211_FREQUENCY_ATTR_PASSIVE_SCAN: Only passive scanning is - * permitted on this channel in current regulatory domain. - * @NL80211_FREQUENCY_ATTR_NO_IBSS: IBSS networks are not permitted - * on this channel in current regulatory domain. + * @NL80211_FREQUENCY_ATTR_NO_IR: no mechanisms that initiate radiation + * are permitted on this channel, this includes sending probe + * requests, or modes of operation that require beaconing. * @NL80211_FREQUENCY_ATTR_RADAR: Radar detection is mandatory * on this channel in current regulatory domain. * @NL80211_FREQUENCY_ATTR_MAX_TX_POWER: Maximum transmission power in mBm @@ -2125,6 +2335,7 @@ enum nl80211_band_attr { * @NL80211_FREQUENCY_ATTR_NO_160MHZ: any 160 MHz (but not 80+80) channel * using this channel as the primary or any of the secondary channels * isn't possible + * @NL80211_FREQUENCY_ATTR_DFS_CAC_TIME: DFS CAC time in milliseconds. * @NL80211_FREQUENCY_ATTR_MAX: highest frequency attribute number * currently defined * @__NL80211_FREQUENCY_ATTR_AFTER_LAST: internal use @@ -2133,8 +2344,8 @@ enum nl80211_frequency_attr { __NL80211_FREQUENCY_ATTR_INVALID, NL80211_FREQUENCY_ATTR_FREQ, NL80211_FREQUENCY_ATTR_DISABLED, - NL80211_FREQUENCY_ATTR_PASSIVE_SCAN, - NL80211_FREQUENCY_ATTR_NO_IBSS, + NL80211_FREQUENCY_ATTR_NO_IR, + __NL80211_FREQUENCY_ATTR_NO_IBSS, NL80211_FREQUENCY_ATTR_RADAR, NL80211_FREQUENCY_ATTR_MAX_TX_POWER, NL80211_FREQUENCY_ATTR_DFS_STATE, @@ -2143,6 +2354,7 @@ enum nl80211_frequency_attr { NL80211_FREQUENCY_ATTR_NO_HT40_PLUS, NL80211_FREQUENCY_ATTR_NO_80MHZ, NL80211_FREQUENCY_ATTR_NO_160MHZ, + NL80211_FREQUENCY_ATTR_DFS_CAC_TIME, /* keep last */ __NL80211_FREQUENCY_ATTR_AFTER_LAST, @@ -2150,6 +2362,9 @@ enum nl80211_frequency_attr { }; #define NL80211_FREQUENCY_ATTR_MAX_TX_POWER NL80211_FREQUENCY_ATTR_MAX_TX_POWER +#define NL80211_FREQUENCY_ATTR_PASSIVE_SCAN NL80211_FREQUENCY_ATTR_NO_IR +#define NL80211_FREQUENCY_ATTR_NO_IBSS NL80211_FREQUENCY_ATTR_NO_IR +#define NL80211_FREQUENCY_ATTR_NO_IR NL80211_FREQUENCY_ATTR_NO_IR /** * enum nl80211_bitrate_attr - bitrate attributes @@ -2230,12 +2445,14 @@ enum nl80211_reg_type { * in KHz. This is not a center a frequency but an actual regulatory * band edge. * @NL80211_ATTR_FREQ_RANGE_MAX_BW: maximum allowed bandwidth for this - * frequency range, in KHz. + * frequency range, in KHz. * @NL80211_ATTR_POWER_RULE_MAX_ANT_GAIN: the maximum allowed antenna gain * for a given frequency range. The value is in mBi (100 * dBi). * If you don't have one then don't send this. * @NL80211_ATTR_POWER_RULE_MAX_EIRP: the maximum allowed EIRP for * a given frequency range. The value is in mBm (100 * dBm). + * @NL80211_ATTR_DFS_CAC_TIME: DFS CAC time in milliseconds. + * If not present or 0 default CAC time will be used. * @NL80211_REG_RULE_ATTR_MAX: highest regulatory rule attribute number * currently defined * @__NL80211_REG_RULE_ATTR_AFTER_LAST: internal use @@ -2251,6 +2468,8 @@ enum nl80211_reg_rule_attr { NL80211_ATTR_POWER_RULE_MAX_ANT_GAIN, NL80211_ATTR_POWER_RULE_MAX_EIRP, + NL80211_ATTR_DFS_CAC_TIME, + /* keep last */ __NL80211_REG_RULE_ATTR_AFTER_LAST, NL80211_REG_RULE_ATTR_MAX = __NL80211_REG_RULE_ATTR_AFTER_LAST - 1 @@ -2260,9 +2479,15 @@ enum nl80211_reg_rule_attr { * enum nl80211_sched_scan_match_attr - scheduled scan match attributes * @__NL80211_SCHED_SCAN_MATCH_ATTR_INVALID: attribute number 0 is reserved * @NL80211_SCHED_SCAN_MATCH_ATTR_SSID: SSID to be used for matching, - * only report BSS with matching SSID. + * only report BSS with matching SSID. * @NL80211_SCHED_SCAN_MATCH_ATTR_RSSI: RSSI threshold (in dBm) for reporting a - * BSS in scan results. Filtering is turned off if not specified. + * BSS in scan results. Filtering is turned off if not specified. Note that + * if this attribute is in a match set of its own, then it is treated as + * the default value for all matchsets with an SSID, rather than being a + * matchset of its own without an RSSI filter. This is due to problems with + * how this API was implemented in the past. Also, due to the same problem, + * the only way to create a matchset with only an RSSI filter (with this + * attribute) is if there's only a single matchset with the RSSI attribute. * @NL80211_SCHED_SCAN_MATCH_ATTR_MAX: highest scheduled scan filter * attribute number currently defined * @__NL80211_SCHED_SCAN_MATCH_ATTR_AFTER_LAST: internal use @@ -2292,8 +2517,12 @@ enum nl80211_sched_scan_match_attr { * @NL80211_RRF_DFS: DFS support is required to be used * @NL80211_RRF_PTP_ONLY: this is only for Point To Point links * @NL80211_RRF_PTMP_ONLY: this is only for Point To Multi Point links - * @NL80211_RRF_PASSIVE_SCAN: passive scan is required - * @NL80211_RRF_NO_IBSS: no IBSS is allowed + * @NL80211_RRF_NO_IR: no mechanisms that initiate radiation are allowed, + * this includes probe requests or modes of operation that require + * beaconing. + * @NL80211_RRF_AUTO_BW: maximum available bandwidth should be calculated + * base on contiguous rules and wider channels will be allowed to cross + * multiple contiguous/overlapping frequency ranges. */ enum nl80211_reg_rule_flags { NL80211_RRF_NO_OFDM = 1<<0, @@ -2303,10 +2532,18 @@ enum nl80211_reg_rule_flags { NL80211_RRF_DFS = 1<<4, NL80211_RRF_PTP_ONLY = 1<<5, NL80211_RRF_PTMP_ONLY = 1<<6, - NL80211_RRF_PASSIVE_SCAN = 1<<7, - NL80211_RRF_NO_IBSS = 1<<8, + NL80211_RRF_NO_IR = 1<<7, + __NL80211_RRF_NO_IBSS = 1<<8, + NL80211_RRF_AUTO_BW = 1<<11, }; +#define NL80211_RRF_PASSIVE_SCAN NL80211_RRF_NO_IR +#define NL80211_RRF_NO_IBSS NL80211_RRF_NO_IR +#define NL80211_RRF_NO_IR NL80211_RRF_NO_IR + +/* For backport compatibility with older userspace */ +#define NL80211_RRF_NO_IR_ALL (NL80211_RRF_NO_IR | __NL80211_RRF_NO_IBSS) + /** * enum nl80211_dfs_regions - regulatory DFS regions * @@ -2395,6 +2632,8 @@ enum nl80211_survey_info { * @NL80211_MNTR_FLAG_OTHER_BSS: disable BSSID filtering * @NL80211_MNTR_FLAG_COOK_FRAMES: report frames after processing. * overrides all other flags. + * @NL80211_MNTR_FLAG_ACTIVE: use the configured MAC address + * and ACK incoming unicast packets. * * @__NL80211_MNTR_FLAG_AFTER_LAST: internal use * @NL80211_MNTR_FLAG_MAX: highest possible monitor flag @@ -2406,6 +2645,7 @@ enum nl80211_mntr_flags { NL80211_MNTR_FLAG_CONTROL, NL80211_MNTR_FLAG_OTHER_BSS, NL80211_MNTR_FLAG_COOK_FRAMES, + NL80211_MNTR_FLAG_ACTIVE, /* keep last */ __NL80211_MNTR_FLAG_AFTER_LAST, @@ -2541,6 +2781,10 @@ enum nl80211_mesh_power_mode { * * @NL80211_MESHCONF_AWAKE_WINDOW: awake window duration (in TUs) * + * @NL80211_MESHCONF_PLINK_TIMEOUT: If no tx activity is seen from a STA we've + * established peering with for longer than this time (in seconds), then + * remove it from the STA's list of peers. Default is 30 minutes. + * * @__NL80211_MESHCONF_ATTR_AFTER_LAST: internal use */ enum nl80211_meshconf_params { @@ -2572,6 +2816,7 @@ enum nl80211_meshconf_params { NL80211_MESHCONF_HWMP_CONFIRMATION_INTERVAL, NL80211_MESHCONF_POWER_MODE, NL80211_MESHCONF_AWAKE_WINDOW, + NL80211_MESHCONF_PLINK_TIMEOUT, /* keep last */ __NL80211_MESHCONF_ATTR_AFTER_LAST, @@ -2619,6 +2864,10 @@ enum nl80211_meshconf_params { * @NL80211_MESH_SETUP_USERSPACE_MPM: Enable this option if userspace will * implement an MPM which handles peer allocation and state. * + * @NL80211_MESH_SETUP_AUTH_PROTOCOL: Inform the kernel of the authentication + * method (u8, as defined in IEEE 8.4.2.100.6, e.g. 0x1 for SAE). + * Default is no authentication method required. + * * @NL80211_MESH_SETUP_ATTR_MAX: highest possible mesh setup attribute number * * @__NL80211_MESH_SETUP_ATTR_AFTER_LAST: Internal use @@ -2632,6 +2881,7 @@ enum nl80211_mesh_setup_params { NL80211_MESH_SETUP_USERSPACE_AMPE, NL80211_MESH_SETUP_ENABLE_VENDOR_SYNC, NL80211_MESH_SETUP_USERSPACE_MPM, + NL80211_MESH_SETUP_AUTH_PROTOCOL, /* keep last */ __NL80211_MESH_SETUP_ATTR_AFTER_LAST, @@ -2712,6 +2962,8 @@ enum nl80211_channel_type { * and %NL80211_ATTR_CENTER_FREQ2 attributes must be provided as well * @NL80211_CHAN_WIDTH_160: 160 MHz channel, the %NL80211_ATTR_CENTER_FREQ1 * attribute must be provided as well + * @NL80211_CHAN_WIDTH_5: 5 MHz OFDM channel + * @NL80211_CHAN_WIDTH_10: 10 MHz OFDM channel */ enum nl80211_chan_width { NL80211_CHAN_WIDTH_20_NOHT, @@ -2720,6 +2972,23 @@ enum nl80211_chan_width { NL80211_CHAN_WIDTH_80, NL80211_CHAN_WIDTH_80P80, NL80211_CHAN_WIDTH_160, + NL80211_CHAN_WIDTH_5, + NL80211_CHAN_WIDTH_10, +}; + +/** + * enum nl80211_bss_scan_width - control channel width for a BSS + * + * These values are used with the %NL80211_BSS_CHAN_WIDTH attribute. + * + * @NL80211_BSS_CHAN_WIDTH_20: control channel is 20 MHz wide or compatible + * @NL80211_BSS_CHAN_WIDTH_10: control channel is 10 MHz wide + * @NL80211_BSS_CHAN_WIDTH_5: control channel is 5 MHz wide + */ +enum nl80211_bss_scan_width { + NL80211_BSS_CHAN_WIDTH_20, + NL80211_BSS_CHAN_WIDTH_10, + NL80211_BSS_CHAN_WIDTH_5, }; /** @@ -2746,6 +3015,8 @@ enum nl80211_chan_width { * @NL80211_BSS_BEACON_IES: binary attribute containing the raw information * elements from a Beacon frame (bin); not present if no Beacon frame has * yet been received + * @NL80211_BSS_CHAN_WIDTH: channel width of the control channel + * (u32, enum nl80211_bss_scan_width) * @__NL80211_BSS_AFTER_LAST: internal * @NL80211_BSS_MAX: highest BSS attribute */ @@ -2762,6 +3033,7 @@ enum nl80211_bss { NL80211_BSS_STATUS, NL80211_BSS_SEEN_MS_AGO, NL80211_BSS_BEACON_IES, + NL80211_BSS_CHAN_WIDTH, /* keep last */ __NL80211_BSS_AFTER_LAST, @@ -2902,21 +3174,43 @@ enum nl80211_key_attributes { * in an array of rates as defined in IEEE 802.11 7.3.2.2 (u8 values with * 1 = 500 kbps) but without the IE length restriction (at most * %NL80211_MAX_SUPP_RATES in a single array). - * @NL80211_TXRATE_MCS: HT (MCS) rates allowed for TX rate selection + * @NL80211_TXRATE_HT: HT (MCS) rates allowed for TX rate selection * in an array of MCS numbers. + * @NL80211_TXRATE_VHT: VHT rates allowed for TX rate selection, + * see &struct nl80211_txrate_vht + * @NL80211_TXRATE_GI: configure GI, see &enum nl80211_txrate_gi * @__NL80211_TXRATE_AFTER_LAST: internal * @NL80211_TXRATE_MAX: highest TX rate attribute */ enum nl80211_tx_rate_attributes { __NL80211_TXRATE_INVALID, NL80211_TXRATE_LEGACY, - NL80211_TXRATE_MCS, + NL80211_TXRATE_HT, + NL80211_TXRATE_VHT, + NL80211_TXRATE_GI, /* keep last */ __NL80211_TXRATE_AFTER_LAST, NL80211_TXRATE_MAX = __NL80211_TXRATE_AFTER_LAST - 1 }; +#define NL80211_TXRATE_MCS NL80211_TXRATE_HT +#define NL80211_VHT_NSS_MAX 8 + +/** + * struct nl80211_txrate_vht - VHT MCS/NSS txrate bitmap + * @mcs: MCS bitmap table for each NSS (array index 0 for 1 stream, etc.) + */ +struct nl80211_txrate_vht { + __u16 mcs[NL80211_VHT_NSS_MAX]; +}; + +enum nl80211_txrate_gi { + NL80211_TXRATE_DEFAULT_GI, + NL80211_TXRATE_FORCE_SGI, + NL80211_TXRATE_FORCE_LGI, +}; + /** * enum nl80211_band - Frequency band * @NL80211_BAND_2GHZ: 2.4 GHz ISM band @@ -3010,11 +3304,11 @@ enum nl80211_tx_power_setting { }; /** - * enum nl80211_wowlan_packet_pattern_attr - WoWLAN packet pattern attribute - * @__NL80211_WOWLAN_PKTPAT_INVALID: invalid number for nested attribute - * @NL80211_WOWLAN_PKTPAT_PATTERN: the pattern, values where the mask has + * enum nl80211_packet_pattern_attr - packet pattern attribute + * @__NL80211_PKTPAT_INVALID: invalid number for nested attribute + * @NL80211_PKTPAT_PATTERN: the pattern, values where the mask has * a zero bit are ignored - * @NL80211_WOWLAN_PKTPAT_MASK: pattern mask, must be long enough to have + * @NL80211_PKTPAT_MASK: pattern mask, must be long enough to have * a bit for each byte in the pattern. The lowest-order bit corresponds * to the first byte of the pattern, but the bytes of the pattern are * in a little-endian-like format, i.e. the 9th byte of the pattern @@ -3025,39 +3319,50 @@ enum nl80211_tx_power_setting { * Note that the pattern matching is done as though frames were not * 802.11 frames but 802.3 frames, i.e. the frame is fully unpacked * first (including SNAP header unpacking) and then matched. - * @NL80211_WOWLAN_PKTPAT_OFFSET: packet offset, pattern is matched after + * @NL80211_PKTPAT_OFFSET: packet offset, pattern is matched after * these fixed number of bytes of received packet - * @NUM_NL80211_WOWLAN_PKTPAT: number of attributes - * @MAX_NL80211_WOWLAN_PKTPAT: max attribute number + * @NUM_NL80211_PKTPAT: number of attributes + * @MAX_NL80211_PKTPAT: max attribute number */ -enum nl80211_wowlan_packet_pattern_attr { - __NL80211_WOWLAN_PKTPAT_INVALID, - NL80211_WOWLAN_PKTPAT_MASK, - NL80211_WOWLAN_PKTPAT_PATTERN, - NL80211_WOWLAN_PKTPAT_OFFSET, - - NUM_NL80211_WOWLAN_PKTPAT, - MAX_NL80211_WOWLAN_PKTPAT = NUM_NL80211_WOWLAN_PKTPAT - 1, +enum nl80211_packet_pattern_attr { + __NL80211_PKTPAT_INVALID, + NL80211_PKTPAT_MASK, + NL80211_PKTPAT_PATTERN, + NL80211_PKTPAT_OFFSET, + + NUM_NL80211_PKTPAT, + MAX_NL80211_PKTPAT = NUM_NL80211_PKTPAT - 1, }; /** - * struct nl80211_wowlan_pattern_support - pattern support information + * struct nl80211_pattern_support - packet pattern support information * @max_patterns: maximum number of patterns supported * @min_pattern_len: minimum length of each pattern * @max_pattern_len: maximum length of each pattern * @max_pkt_offset: maximum Rx packet offset * * This struct is carried in %NL80211_WOWLAN_TRIG_PKT_PATTERN when - * that is part of %NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED in the - * capability information given by the kernel to userspace. + * that is part of %NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED or in + * %NL80211_ATTR_COALESCE_RULE_PKT_PATTERN when that is part of + * %NL80211_ATTR_COALESCE_RULE in the capability information given + * by the kernel to userspace. */ -struct nl80211_wowlan_pattern_support { +struct nl80211_pattern_support { __u32 max_patterns; __u32 min_pattern_len; __u32 max_pattern_len; __u32 max_pkt_offset; } __attribute__((packed)); +/* only for backward compatibility */ +#define __NL80211_WOWLAN_PKTPAT_INVALID __NL80211_PKTPAT_INVALID +#define NL80211_WOWLAN_PKTPAT_MASK NL80211_PKTPAT_MASK +#define NL80211_WOWLAN_PKTPAT_PATTERN NL80211_PKTPAT_PATTERN +#define NL80211_WOWLAN_PKTPAT_OFFSET NL80211_PKTPAT_OFFSET +#define NUM_NL80211_WOWLAN_PKTPAT NUM_NL80211_PKTPAT +#define MAX_NL80211_WOWLAN_PKTPAT MAX_NL80211_PKTPAT +#define nl80211_wowlan_pattern_support nl80211_pattern_support + /** * enum nl80211_wowlan_triggers - WoWLAN trigger definitions * @__NL80211_WOWLAN_TRIG_INVALID: invalid number for nested attributes @@ -3077,7 +3382,7 @@ struct nl80211_wowlan_pattern_support { * pattern matching is done after the packet is converted to the MSDU. * * In %NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED, it is a binary attribute - * carrying a &struct nl80211_wowlan_pattern_support. + * carrying a &struct nl80211_pattern_support. * * When reporting wakeup. it is a u32 attribute containing the 0-based * index of the pattern that caused the wakeup, in the patterns passed @@ -3234,7 +3539,7 @@ struct nl80211_wowlan_tcp_data_token_feature { * @NL80211_WOWLAN_TCP_WAKE_PAYLOAD: wake packet payload, for advertising a * u32 attribute holding the maximum length * @NL80211_WOWLAN_TCP_WAKE_MASK: Wake packet payload mask, not used for - * feature advertising. The mask works like @NL80211_WOWLAN_PKTPAT_MASK + * feature advertising. The mask works like @NL80211_PKTPAT_MASK * but on the TCP payload only. * @NUM_NL80211_WOWLAN_TCP: number of TCP attributes * @MAX_NL80211_WOWLAN_TCP: highest attribute number @@ -3259,6 +3564,55 @@ enum nl80211_wowlan_tcp_attrs { }; /** + * struct nl80211_coalesce_rule_support - coalesce rule support information + * @max_rules: maximum number of rules supported + * @pat: packet pattern support information + * @max_delay: maximum supported coalescing delay in msecs + * + * This struct is carried in %NL80211_ATTR_COALESCE_RULE in the + * capability information given by the kernel to userspace. + */ +struct nl80211_coalesce_rule_support { + __u32 max_rules; + struct nl80211_pattern_support pat; + __u32 max_delay; +} __attribute__((packed)); + +/** + * enum nl80211_attr_coalesce_rule - coalesce rule attribute + * @__NL80211_COALESCE_RULE_INVALID: invalid number for nested attribute + * @NL80211_ATTR_COALESCE_RULE_DELAY: delay in msecs used for packet coalescing + * @NL80211_ATTR_COALESCE_RULE_CONDITION: condition for packet coalescence, + * see &enum nl80211_coalesce_condition. + * @NL80211_ATTR_COALESCE_RULE_PKT_PATTERN: packet offset, pattern is matched + * after these fixed number of bytes of received packet + * @NUM_NL80211_ATTR_COALESCE_RULE: number of attributes + * @NL80211_ATTR_COALESCE_RULE_MAX: max attribute number + */ +enum nl80211_attr_coalesce_rule { + __NL80211_COALESCE_RULE_INVALID, + NL80211_ATTR_COALESCE_RULE_DELAY, + NL80211_ATTR_COALESCE_RULE_CONDITION, + NL80211_ATTR_COALESCE_RULE_PKT_PATTERN, + + /* keep last */ + NUM_NL80211_ATTR_COALESCE_RULE, + NL80211_ATTR_COALESCE_RULE_MAX = NUM_NL80211_ATTR_COALESCE_RULE - 1 +}; + +/** + * enum nl80211_coalesce_condition - coalesce rule conditions + * @NL80211_COALESCE_CONDITION_MATCH: coalaesce Rx packets when patterns + * in a rule are matched. + * @NL80211_COALESCE_CONDITION_NO_MATCH: coalesce Rx packets when patterns + * in a rule are not matched. + */ +enum nl80211_coalesce_condition { + NL80211_COALESCE_CONDITION_MATCH, + NL80211_COALESCE_CONDITION_NO_MATCH +}; + +/** * enum nl80211_iface_limit_attrs - limit attributes * @NL80211_IFACE_LIMIT_UNSPEC: (reserved) * @NL80211_IFACE_LIMIT_MAX: maximum number of interfaces that @@ -3502,11 +3856,6 @@ enum nl80211_ap_sme_features { * @NL80211_FEATURE_CELL_BASE_REG_HINTS: This driver has been tested * to work properly to suppport receiving regulatory hints from * cellular base stations. - * @NL80211_FEATURE_P2P_DEVICE_NEEDS_CHANNEL: If this is set, an active - * P2P Device (%NL80211_IFTYPE_P2P_DEVICE) requires its own channel - * in the interface combinations, even when it's only used for scan - * and remain-on-channel. This could be due to, for example, the - * remain-on-channel implementation requiring a channel context. * @NL80211_FEATURE_SAE: This driver supports simultaneous authentication of * equals (SAE) with user space SME (NL80211_CMD_AUTHENTICATE) in station * mode @@ -3538,13 +3887,17 @@ enum nl80211_ap_sme_features { * Peering Management entity which may be implemented by registering for * beacons or NL80211_CMD_NEW_PEER_CANDIDATE events. The mesh beacon is * still generated by the driver. + * @NL80211_FEATURE_ACTIVE_MONITOR: This driver supports an active monitor + * interface. An active monitor interface behaves like a normal monitor + * interface, but gets added to the driver. It ensures that incoming + * unicast packets directed at the configured interface address get ACKed. */ enum nl80211_feature_flags { NL80211_FEATURE_SK_TX_STATUS = 1 << 0, NL80211_FEATURE_HT_IBSS = 1 << 1, NL80211_FEATURE_INACTIVITY_TIMER = 1 << 2, NL80211_FEATURE_CELL_BASE_REG_HINTS = 1 << 3, - NL80211_FEATURE_P2P_DEVICE_NEEDS_CHANNEL = 1 << 4, + /* bit 4 is reserved - don't use */ NL80211_FEATURE_SAE = 1 << 5, NL80211_FEATURE_LOW_PRIORITY_SCAN = 1 << 6, NL80211_FEATURE_SCAN_FLUSH = 1 << 7, @@ -3557,6 +3910,7 @@ enum nl80211_feature_flags { NL80211_FEATURE_ADVERTISE_CHAN_LIMITS = 1 << 14, NL80211_FEATURE_FULL_AP_CLIENT_STATE = 1 << 15, NL80211_FEATURE_USERSPACE_MPM = 1 << 16, + NL80211_FEATURE_ACTIVE_MONITOR = 1 << 17, }; /** @@ -3657,13 +4011,12 @@ enum nl80211_radar_event { * * Channel states used by the DFS code. * - * @IEEE80211_DFS_USABLE: The channel can be used, but channel availability + * @NL80211_DFS_USABLE: The channel can be used, but channel availability * check (CAC) must be performed before using it for AP or IBSS. - * @IEEE80211_DFS_UNAVAILABLE: A radar has been detected on this channel, it + * @NL80211_DFS_UNAVAILABLE: A radar has been detected on this channel, it * is therefore marked as not available. - * @IEEE80211_DFS_AVAILABLE: The channel has been CAC checked and is available. + * @NL80211_DFS_AVAILABLE: The channel has been CAC checked and is available. */ - enum nl80211_dfs_state { NL80211_DFS_USABLE, NL80211_DFS_UNAVAILABLE, @@ -3682,4 +4035,72 @@ enum nl80211_protocol_features { NL80211_PROTOCOL_FEATURE_SPLIT_WIPHY_DUMP = 1 << 0, }; +/** + * enum nl80211_crit_proto_id - nl80211 critical protocol identifiers + * + * @NL80211_CRIT_PROTO_UNSPEC: protocol unspecified. + * @NL80211_CRIT_PROTO_DHCP: BOOTP or DHCPv6 protocol. + * @NL80211_CRIT_PROTO_EAPOL: EAPOL protocol. + * @NL80211_CRIT_PROTO_APIPA: APIPA protocol. + * @NUM_NL80211_CRIT_PROTO: must be kept last. + */ +enum nl80211_crit_proto_id { + NL80211_CRIT_PROTO_UNSPEC, + NL80211_CRIT_PROTO_DHCP, + NL80211_CRIT_PROTO_EAPOL, + NL80211_CRIT_PROTO_APIPA, + /* add other protocols before this one */ + NUM_NL80211_CRIT_PROTO +}; + +/* maximum duration for critical protocol measures */ +#define NL80211_CRIT_PROTO_MAX_DURATION 5000 /* msec */ + +/** + * enum nl80211_rxmgmt_flags - flags for received management frame. + * + * Used by cfg80211_rx_mgmt() + * + * @NL80211_RXMGMT_FLAG_ANSWERED: frame was answered by device/driver. + */ +enum nl80211_rxmgmt_flags { + NL80211_RXMGMT_FLAG_ANSWERED = 1 << 0, +}; + +/* + * If this flag is unset, the lower 24 bits are an OUI, if set + * a Linux nl80211 vendor ID is used (no such IDs are allocated + * yet, so that's not valid so far) + */ +#define NL80211_VENDOR_ID_IS_LINUX 0x80000000 + +/** + * struct nl80211_vendor_cmd_info - vendor command data + * @vendor_id: If the %NL80211_VENDOR_ID_IS_LINUX flag is clear, then the + * value is a 24-bit OUI; if it is set then a separately allocated ID + * may be used, but no such IDs are allocated yet. New IDs should be + * added to this file when needed. + * @subcmd: sub-command ID for the command + */ +struct nl80211_vendor_cmd_info { + __u32 vendor_id; + __u32 subcmd; +}; + +/** + * enum nl80211_tdls_peer_capability - TDLS peer flags. + * + * Used by tdls_mgmt() to determine which conditional elements need + * to be added to TDLS Setup frames. + * + * @NL80211_TDLS_PEER_HT: TDLS peer is HT capable. + * @NL80211_TDLS_PEER_VHT: TDLS peer is VHT capable. + * @NL80211_TDLS_PEER_WMM: TDLS peer is WMM capable. + */ +enum nl80211_tdls_peer_capability { + NL80211_TDLS_PEER_HT = 1<<0, + NL80211_TDLS_PEER_VHT = 1<<1, + NL80211_TDLS_PEER_WMM = 1<<2, +}; + #endif /* __LINUX_NL80211_H */ diff --git a/reglib.h b/reglib.h index d570c36..afd5ef6 100644 --- a/reglib.h +++ b/reglib.h @@ -37,9 +37,6 @@ struct ieee80211_regdomain { struct ieee80211_reg_rule reg_rules[]; }; -/* Remove this once upstream nl80211.h gets this */ -#define NL80211_RRF_NO_IR (1<<7) - #define REGLIB_MHZ_TO_KHZ(freq) ((freq) * 1000) #define REGLIB_KHZ_TO_MHZ(freq) ((freq) / 1000) #define REGLIB_DBI_TO_MBI(gain) ((gain) * 100) -- 1.7.9.5 ^ permalink raw reply related [flat|nested] 13+ messages in thread
* [wireless-regdb] [PATCH 1/2] crda: sync with latest nl80211.h @ 2014-05-09 8:38 ` Janusz Dziedzic 0 siblings, 0 replies; 13+ messages in thread From: Janusz Dziedzic @ 2014-05-09 8:38 UTC (permalink / raw) To: wireless-regdb; +Cc: Janusz Dziedzic, linux-wireless, mcgrof Sync with latest nl80211.h wireless-testing. Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com> --- nl80211.h | 525 +++++++++++++++++++++++++++++++++++++++++++++++++++++++------ reglib.h | 3 - 2 files changed, 473 insertions(+), 55 deletions(-) diff --git a/nl80211.h b/nl80211.h index 79da871..1ba9d62 100644 --- a/nl80211.h +++ b/nl80211.h @@ -27,6 +27,8 @@ #include <linux/types.h> +#define NL80211_GENL_NAME "nl80211" + /** * DOC: Station handling * @@ -124,6 +126,31 @@ */ /** + * DOC: packet coalesce support + * + * In most cases, host that receives IPv4 and IPv6 multicast/broadcast + * packets does not do anything with these packets. Therefore the + * reception of these unwanted packets causes unnecessary processing + * and power consumption. + * + * Packet coalesce feature helps to reduce number of received interrupts + * to host by buffering these packets in firmware/hardware for some + * predefined time. Received interrupt will be generated when one of the + * following events occur. + * a) Expiration of hardware timer whose expiration time is set to maximum + * coalescing delay of matching coalesce rule. + * b) Coalescing buffer in hardware reaches it's limit. + * c) Packet doesn't match any of the configured coalesce rules. + * + * User needs to configure following parameters for creating a coalesce + * rule. + * a) Maximum coalescing delay + * b) List of packet patterns which needs to be matched + * c) Condition for coalescence. pattern 'match' or 'no match' + * Multiple such rules can be created. + */ + +/** * enum nl80211_commands - supported nl80211 commands * * @NL80211_CMD_UNSPEC: unspecified command to catch errors @@ -276,8 +303,9 @@ * passed, all channels allowed for the current regulatory domain * are used. Extra IEs can also be passed from the userspace by * using the %NL80211_ATTR_IE attribute. - * @NL80211_CMD_STOP_SCHED_SCAN: stop a scheduled scan. Returns -ENOENT - * if scheduled scan is not running. + * @NL80211_CMD_STOP_SCHED_SCAN: stop a scheduled scan. Returns -ENOENT if + * scheduled scan is not running. The caller may assume that as soon + * as the call returns, it is safe to start a new scheduled scan again. * @NL80211_CMD_SCHED_SCAN_RESULTS: indicates that there are scheduled scan * results available. * @NL80211_CMD_SCHED_SCAN_STOPPED: indicates that the scheduled scan has @@ -391,8 +419,18 @@ * %NL80211_ATTR_SSID attribute, and can optionally specify the association * IEs in %NL80211_ATTR_IE, %NL80211_ATTR_AUTH_TYPE, %NL80211_ATTR_USE_MFP, * %NL80211_ATTR_MAC, %NL80211_ATTR_WIPHY_FREQ, %NL80211_ATTR_CONTROL_PORT, - * %NL80211_ATTR_CONTROL_PORT_ETHERTYPE and - * %NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT. + * %NL80211_ATTR_CONTROL_PORT_ETHERTYPE, + * %NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT, %NL80211_ATTR_MAC_HINT, and + * %NL80211_ATTR_WIPHY_FREQ_HINT. + * If included, %NL80211_ATTR_MAC and %NL80211_ATTR_WIPHY_FREQ are + * restrictions on BSS selection, i.e., they effectively prevent roaming + * within the ESS. %NL80211_ATTR_MAC_HINT and %NL80211_ATTR_WIPHY_FREQ_HINT + * can be included to provide a recommendation of the initial BSS while + * allowing the driver to roam to other BSSes within the ESS and also to + * ignore this recommendation if the indicated BSS is not ideal. Only one + * set of BSSID,frequency parameters is used (i.e., either the enforcing + * %NL80211_ATTR_MAC,%NL80211_ATTR_WIPHY_FREQ or the less strict + * %NL80211_ATTR_MAC_HINT and %NL80211_ATTR_WIPHY_FREQ_HINT). * Background scan period can optionally be * specified in %NL80211_ATTR_BG_SCAN_PERIOD, * if not specified default background scan configuration @@ -554,7 +592,14 @@ * operation, %NL80211_ATTR_MAC contains the peer MAC address, and * %NL80211_ATTR_REASON_CODE the reason code to be used (only with * %NL80211_TDLS_TEARDOWN). - * @NL80211_CMD_TDLS_MGMT: Send a TDLS management frame. + * @NL80211_CMD_TDLS_MGMT: Send a TDLS management frame. The + * %NL80211_ATTR_TDLS_ACTION attribute determines the type of frame to be + * sent. Public Action codes (802.11-2012 8.1.5.1) will be sent as + * 802.11 management frames, while TDLS action codes (802.11-2012 + * 8.5.13.1) will be encapsulated and sent as data frames. The currently + * supported Public Action code is %WLAN_PUB_ACTION_TDLS_DISCOVER_RES + * and the currently supported TDLS actions codes are given in + * &enum ieee80211_tdls_actioncode. * * @NL80211_CMD_UNEXPECTED_FRAME: Used by an application controlling an AP * (or GO) interface (i.e. hostapd) to ask for unexpected frames to @@ -639,6 +684,41 @@ * with the relevant Information Elements. This event is used to report * received FT IEs (MDIE, FTIE, RSN IE, TIE, RICIE). * + * @NL80211_CMD_CRIT_PROTOCOL_START: Indicates user-space will start running + * a critical protocol that needs more reliability in the connection to + * complete. + * + * @NL80211_CMD_CRIT_PROTOCOL_STOP: Indicates the connection reliability can + * return back to normal. + * + * @NL80211_CMD_GET_COALESCE: Get currently supported coalesce rules. + * @NL80211_CMD_SET_COALESCE: Configure coalesce rules or clear existing rules. + * + * @NL80211_CMD_CHANNEL_SWITCH: Perform a channel switch by announcing the + * the new channel information (Channel Switch Announcement - CSA) + * in the beacon for some time (as defined in the + * %NL80211_ATTR_CH_SWITCH_COUNT parameter) and then change to the + * new channel. Userspace provides the new channel information (using + * %NL80211_ATTR_WIPHY_FREQ and the attributes determining channel + * width). %NL80211_ATTR_CH_SWITCH_BLOCK_TX may be supplied to inform + * other station that transmission must be blocked until the channel + * switch is complete. + * + * @NL80211_CMD_VENDOR: Vendor-specified command/event. The command is specified + * by the %NL80211_ATTR_VENDOR_ID attribute and a sub-command in + * %NL80211_ATTR_VENDOR_SUBCMD. Parameter(s) can be transported in + * %NL80211_ATTR_VENDOR_DATA. + * For feature advertisement, the %NL80211_ATTR_VENDOR_DATA attribute is + * used in the wiphy data as a nested attribute containing descriptions + * (&struct nl80211_vendor_cmd_info) of the supported vendor commands. + * This may also be sent as an event with the same attributes. + * + * @NL80211_CMD_SET_QOS_MAP: Set Interworking QoS mapping for IP DSCP values. + * The QoS mapping information is included in %NL80211_ATTR_QOS_MAP. If + * that attribute is not included, QoS mapping is disabled. Since this + * QoS mapping is relevant for IP packets, it is only valid during an + * association. This is cleared on disassociation and AP restart. + * * @NL80211_CMD_MAX: highest used command number * @__NL80211_CMD_AFTER_LAST: internal use */ @@ -798,6 +878,18 @@ enum nl80211_commands { NL80211_CMD_UPDATE_FT_IES, NL80211_CMD_FT_EVENT, + NL80211_CMD_CRIT_PROTOCOL_START, + NL80211_CMD_CRIT_PROTOCOL_STOP, + + NL80211_CMD_GET_COALESCE, + NL80211_CMD_SET_COALESCE, + + NL80211_CMD_CHANNEL_SWITCH, + + NL80211_CMD_VENDOR, + + NL80211_CMD_SET_QOS_MAP, + /* add new commands above here */ /* used to define NL80211_CMD_MAX below */ @@ -933,7 +1025,7 @@ enum nl80211_commands { * to query the CRDA to retrieve one regulatory domain. This attribute can * also be used by userspace to query the kernel for the currently set * regulatory domain. We chose an alpha2 as that is also used by the - * IEEE-802.11d country information element to identify a country. + * IEEE-802.11 country information element to identify a country. * Users can also simply ask the wireless core to set regulatory domain * to a specific alpha2. * @NL80211_ATTR_REG_RULES: a nested array of regulatory domain regulatory @@ -1414,6 +1506,79 @@ enum nl80211_commands { * @NL80211_ATTR_IE_RIC: Resource Information Container Information * Element * + * @NL80211_ATTR_CRIT_PROT_ID: critical protocol identifier requiring increased + * reliability, see &enum nl80211_crit_proto_id (u16). + * @NL80211_ATTR_MAX_CRIT_PROT_DURATION: duration in milliseconds in which + * the connection should have increased reliability (u16). + * + * @NL80211_ATTR_PEER_AID: Association ID for the peer TDLS station (u16). + * This is similar to @NL80211_ATTR_STA_AID but with a difference of being + * allowed to be used with the first @NL80211_CMD_SET_STATION command to + * update a TDLS peer STA entry. + * + * @NL80211_ATTR_COALESCE_RULE: Coalesce rule information. + * + * @NL80211_ATTR_CH_SWITCH_COUNT: u32 attribute specifying the number of TBTT's + * until the channel switch event. + * @NL80211_ATTR_CH_SWITCH_BLOCK_TX: flag attribute specifying that transmission + * must be blocked on the current channel (before the channel switch + * operation). + * @NL80211_ATTR_CSA_IES: Nested set of attributes containing the IE information + * for the time while performing a channel switch. + * @NL80211_ATTR_CSA_C_OFF_BEACON: Offset of the channel switch counter + * field in the beacons tail (%NL80211_ATTR_BEACON_TAIL). + * @NL80211_ATTR_CSA_C_OFF_PRESP: Offset of the channel switch counter + * field in the probe response (%NL80211_ATTR_PROBE_RESP). + * + * @NL80211_ATTR_RXMGMT_FLAGS: flags for nl80211_send_mgmt(), u32. + * As specified in the &enum nl80211_rxmgmt_flags. + * + * @NL80211_ATTR_STA_SUPPORTED_CHANNELS: array of supported channels. + * + * @NL80211_ATTR_STA_SUPPORTED_OPER_CLASSES: array of supported + * supported operating classes. + * + * @NL80211_ATTR_HANDLE_DFS: A flag indicating whether user space + * controls DFS operation in IBSS mode. If the flag is included in + * %NL80211_CMD_JOIN_IBSS request, the driver will allow use of DFS + * channels and reports radar events to userspace. Userspace is required + * to react to radar events, e.g. initiate a channel switch or leave the + * IBSS network. + * + * @NL80211_ATTR_SUPPORT_5_MHZ: A flag indicating that the device supports + * 5 MHz channel bandwidth. + * @NL80211_ATTR_SUPPORT_10_MHZ: A flag indicating that the device supports + * 10 MHz channel bandwidth. + * + * @NL80211_ATTR_OPMODE_NOTIF: Operating mode field from Operating Mode + * Notification Element based on association request when used with + * %NL80211_CMD_NEW_STATION; u8 attribute. + * + * @NL80211_ATTR_VENDOR_ID: The vendor ID, either a 24-bit OUI or, if + * %NL80211_VENDOR_ID_IS_LINUX is set, a special Linux ID (not used yet) + * @NL80211_ATTR_VENDOR_SUBCMD: vendor sub-command + * @NL80211_ATTR_VENDOR_DATA: data for the vendor command, if any; this + * attribute is also used for vendor command feature advertisement + * @NL80211_ATTR_VENDOR_EVENTS: used for event list advertising in the wiphy + * info, containing a nested array of possible events + * + * @NL80211_ATTR_QOS_MAP: IP DSCP mapping for Interworking QoS mapping. This + * data is in the format defined for the payload of the QoS Map Set element + * in IEEE Std 802.11-2012, 8.4.2.97. + * + * @NL80211_ATTR_MAC_HINT: MAC address recommendation as initial BSS + * @NL80211_ATTR_WIPHY_FREQ_HINT: frequency of the recommended initial BSS + * + * @NL80211_ATTR_MAX_AP_ASSOC_STA: Device attribute that indicates how many + * associated stations are supported in AP mode (including P2P GO); u32. + * Since drivers may not have a fixed limit on the maximum number (e.g., + * other concurrent operations may affect this), drivers are allowed to + * advertise values that cannot always be met. In such cases, an attempt + * to add a new station entry with @NL80211_CMD_NEW_STATION may fail. + * + * @NL80211_ATTR_TDLS_PEER_CAPABILITY: flags for TDLS peer capabilities, u32. + * As specified in the &enum nl80211_tdls_peer_capability. + * * @NL80211_ATTR_MAX: highest attribute number currently defined * @__NL80211_ATTR_AFTER_LAST: internal use */ @@ -1709,6 +1874,46 @@ enum nl80211_attrs { NL80211_ATTR_MDID, NL80211_ATTR_IE_RIC, + NL80211_ATTR_CRIT_PROT_ID, + NL80211_ATTR_MAX_CRIT_PROT_DURATION, + + NL80211_ATTR_PEER_AID, + + NL80211_ATTR_COALESCE_RULE, + + NL80211_ATTR_CH_SWITCH_COUNT, + NL80211_ATTR_CH_SWITCH_BLOCK_TX, + NL80211_ATTR_CSA_IES, + NL80211_ATTR_CSA_C_OFF_BEACON, + NL80211_ATTR_CSA_C_OFF_PRESP, + + NL80211_ATTR_RXMGMT_FLAGS, + + NL80211_ATTR_STA_SUPPORTED_CHANNELS, + + NL80211_ATTR_STA_SUPPORTED_OPER_CLASSES, + + NL80211_ATTR_HANDLE_DFS, + + NL80211_ATTR_SUPPORT_5_MHZ, + NL80211_ATTR_SUPPORT_10_MHZ, + + NL80211_ATTR_OPMODE_NOTIF, + + NL80211_ATTR_VENDOR_ID, + NL80211_ATTR_VENDOR_SUBCMD, + NL80211_ATTR_VENDOR_DATA, + NL80211_ATTR_VENDOR_EVENTS, + + NL80211_ATTR_QOS_MAP, + + NL80211_ATTR_MAC_HINT, + NL80211_ATTR_WIPHY_FREQ_HINT, + + NL80211_ATTR_MAX_AP_ASSOC_STA, + + NL80211_ATTR_TDLS_PEER_CAPABILITY, + /* add attributes here, update the policy in nl80211.c */ __NL80211_ATTR_AFTER_LAST, @@ -1973,6 +2178,10 @@ enum nl80211_sta_bss_param { * @NL80211_STA_INFO_PEER_PM: peer mesh STA link-specific power mode * @NL80211_STA_INFO_NONPEER_PM: neighbor mesh STA power save mode towards * non-peer STA + * @NL80211_STA_INFO_CHAIN_SIGNAL: per-chain signal strength of last PPDU + * Contains a nested array of signal strength attributes (u8, dBm) + * @NL80211_STA_INFO_CHAIN_SIGNAL_AVG: per-chain signal strength average + * Same format as NL80211_STA_INFO_CHAIN_SIGNAL. * @__NL80211_STA_INFO_AFTER_LAST: internal * @NL80211_STA_INFO_MAX: highest possible station info attribute */ @@ -2002,6 +2211,8 @@ enum nl80211_sta_info { NL80211_STA_INFO_NONPEER_PM, NL80211_STA_INFO_RX_BYTES64, NL80211_STA_INFO_TX_BYTES64, + NL80211_STA_INFO_CHAIN_SIGNAL, + NL80211_STA_INFO_CHAIN_SIGNAL_AVG, /* keep last */ __NL80211_STA_INFO_AFTER_LAST, @@ -2103,10 +2314,9 @@ enum nl80211_band_attr { * @NL80211_FREQUENCY_ATTR_FREQ: Frequency in MHz * @NL80211_FREQUENCY_ATTR_DISABLED: Channel is disabled in current * regulatory domain. - * @NL80211_FREQUENCY_ATTR_PASSIVE_SCAN: Only passive scanning is - * permitted on this channel in current regulatory domain. - * @NL80211_FREQUENCY_ATTR_NO_IBSS: IBSS networks are not permitted - * on this channel in current regulatory domain. + * @NL80211_FREQUENCY_ATTR_NO_IR: no mechanisms that initiate radiation + * are permitted on this channel, this includes sending probe + * requests, or modes of operation that require beaconing. * @NL80211_FREQUENCY_ATTR_RADAR: Radar detection is mandatory * on this channel in current regulatory domain. * @NL80211_FREQUENCY_ATTR_MAX_TX_POWER: Maximum transmission power in mBm @@ -2125,6 +2335,7 @@ enum nl80211_band_attr { * @NL80211_FREQUENCY_ATTR_NO_160MHZ: any 160 MHz (but not 80+80) channel * using this channel as the primary or any of the secondary channels * isn't possible + * @NL80211_FREQUENCY_ATTR_DFS_CAC_TIME: DFS CAC time in milliseconds. * @NL80211_FREQUENCY_ATTR_MAX: highest frequency attribute number * currently defined * @__NL80211_FREQUENCY_ATTR_AFTER_LAST: internal use @@ -2133,8 +2344,8 @@ enum nl80211_frequency_attr { __NL80211_FREQUENCY_ATTR_INVALID, NL80211_FREQUENCY_ATTR_FREQ, NL80211_FREQUENCY_ATTR_DISABLED, - NL80211_FREQUENCY_ATTR_PASSIVE_SCAN, - NL80211_FREQUENCY_ATTR_NO_IBSS, + NL80211_FREQUENCY_ATTR_NO_IR, + __NL80211_FREQUENCY_ATTR_NO_IBSS, NL80211_FREQUENCY_ATTR_RADAR, NL80211_FREQUENCY_ATTR_MAX_TX_POWER, NL80211_FREQUENCY_ATTR_DFS_STATE, @@ -2143,6 +2354,7 @@ enum nl80211_frequency_attr { NL80211_FREQUENCY_ATTR_NO_HT40_PLUS, NL80211_FREQUENCY_ATTR_NO_80MHZ, NL80211_FREQUENCY_ATTR_NO_160MHZ, + NL80211_FREQUENCY_ATTR_DFS_CAC_TIME, /* keep last */ __NL80211_FREQUENCY_ATTR_AFTER_LAST, @@ -2150,6 +2362,9 @@ enum nl80211_frequency_attr { }; #define NL80211_FREQUENCY_ATTR_MAX_TX_POWER NL80211_FREQUENCY_ATTR_MAX_TX_POWER +#define NL80211_FREQUENCY_ATTR_PASSIVE_SCAN NL80211_FREQUENCY_ATTR_NO_IR +#define NL80211_FREQUENCY_ATTR_NO_IBSS NL80211_FREQUENCY_ATTR_NO_IR +#define NL80211_FREQUENCY_ATTR_NO_IR NL80211_FREQUENCY_ATTR_NO_IR /** * enum nl80211_bitrate_attr - bitrate attributes @@ -2230,12 +2445,14 @@ enum nl80211_reg_type { * in KHz. This is not a center a frequency but an actual regulatory * band edge. * @NL80211_ATTR_FREQ_RANGE_MAX_BW: maximum allowed bandwidth for this - * frequency range, in KHz. + * frequency range, in KHz. * @NL80211_ATTR_POWER_RULE_MAX_ANT_GAIN: the maximum allowed antenna gain * for a given frequency range. The value is in mBi (100 * dBi). * If you don't have one then don't send this. * @NL80211_ATTR_POWER_RULE_MAX_EIRP: the maximum allowed EIRP for * a given frequency range. The value is in mBm (100 * dBm). + * @NL80211_ATTR_DFS_CAC_TIME: DFS CAC time in milliseconds. + * If not present or 0 default CAC time will be used. * @NL80211_REG_RULE_ATTR_MAX: highest regulatory rule attribute number * currently defined * @__NL80211_REG_RULE_ATTR_AFTER_LAST: internal use @@ -2251,6 +2468,8 @@ enum nl80211_reg_rule_attr { NL80211_ATTR_POWER_RULE_MAX_ANT_GAIN, NL80211_ATTR_POWER_RULE_MAX_EIRP, + NL80211_ATTR_DFS_CAC_TIME, + /* keep last */ __NL80211_REG_RULE_ATTR_AFTER_LAST, NL80211_REG_RULE_ATTR_MAX = __NL80211_REG_RULE_ATTR_AFTER_LAST - 1 @@ -2260,9 +2479,15 @@ enum nl80211_reg_rule_attr { * enum nl80211_sched_scan_match_attr - scheduled scan match attributes * @__NL80211_SCHED_SCAN_MATCH_ATTR_INVALID: attribute number 0 is reserved * @NL80211_SCHED_SCAN_MATCH_ATTR_SSID: SSID to be used for matching, - * only report BSS with matching SSID. + * only report BSS with matching SSID. * @NL80211_SCHED_SCAN_MATCH_ATTR_RSSI: RSSI threshold (in dBm) for reporting a - * BSS in scan results. Filtering is turned off if not specified. + * BSS in scan results. Filtering is turned off if not specified. Note that + * if this attribute is in a match set of its own, then it is treated as + * the default value for all matchsets with an SSID, rather than being a + * matchset of its own without an RSSI filter. This is due to problems with + * how this API was implemented in the past. Also, due to the same problem, + * the only way to create a matchset with only an RSSI filter (with this + * attribute) is if there's only a single matchset with the RSSI attribute. * @NL80211_SCHED_SCAN_MATCH_ATTR_MAX: highest scheduled scan filter * attribute number currently defined * @__NL80211_SCHED_SCAN_MATCH_ATTR_AFTER_LAST: internal use @@ -2292,8 +2517,12 @@ enum nl80211_sched_scan_match_attr { * @NL80211_RRF_DFS: DFS support is required to be used * @NL80211_RRF_PTP_ONLY: this is only for Point To Point links * @NL80211_RRF_PTMP_ONLY: this is only for Point To Multi Point links - * @NL80211_RRF_PASSIVE_SCAN: passive scan is required - * @NL80211_RRF_NO_IBSS: no IBSS is allowed + * @NL80211_RRF_NO_IR: no mechanisms that initiate radiation are allowed, + * this includes probe requests or modes of operation that require + * beaconing. + * @NL80211_RRF_AUTO_BW: maximum available bandwidth should be calculated + * base on contiguous rules and wider channels will be allowed to cross + * multiple contiguous/overlapping frequency ranges. */ enum nl80211_reg_rule_flags { NL80211_RRF_NO_OFDM = 1<<0, @@ -2303,10 +2532,18 @@ enum nl80211_reg_rule_flags { NL80211_RRF_DFS = 1<<4, NL80211_RRF_PTP_ONLY = 1<<5, NL80211_RRF_PTMP_ONLY = 1<<6, - NL80211_RRF_PASSIVE_SCAN = 1<<7, - NL80211_RRF_NO_IBSS = 1<<8, + NL80211_RRF_NO_IR = 1<<7, + __NL80211_RRF_NO_IBSS = 1<<8, + NL80211_RRF_AUTO_BW = 1<<11, }; +#define NL80211_RRF_PASSIVE_SCAN NL80211_RRF_NO_IR +#define NL80211_RRF_NO_IBSS NL80211_RRF_NO_IR +#define NL80211_RRF_NO_IR NL80211_RRF_NO_IR + +/* For backport compatibility with older userspace */ +#define NL80211_RRF_NO_IR_ALL (NL80211_RRF_NO_IR | __NL80211_RRF_NO_IBSS) + /** * enum nl80211_dfs_regions - regulatory DFS regions * @@ -2395,6 +2632,8 @@ enum nl80211_survey_info { * @NL80211_MNTR_FLAG_OTHER_BSS: disable BSSID filtering * @NL80211_MNTR_FLAG_COOK_FRAMES: report frames after processing. * overrides all other flags. + * @NL80211_MNTR_FLAG_ACTIVE: use the configured MAC address + * and ACK incoming unicast packets. * * @__NL80211_MNTR_FLAG_AFTER_LAST: internal use * @NL80211_MNTR_FLAG_MAX: highest possible monitor flag @@ -2406,6 +2645,7 @@ enum nl80211_mntr_flags { NL80211_MNTR_FLAG_CONTROL, NL80211_MNTR_FLAG_OTHER_BSS, NL80211_MNTR_FLAG_COOK_FRAMES, + NL80211_MNTR_FLAG_ACTIVE, /* keep last */ __NL80211_MNTR_FLAG_AFTER_LAST, @@ -2541,6 +2781,10 @@ enum nl80211_mesh_power_mode { * * @NL80211_MESHCONF_AWAKE_WINDOW: awake window duration (in TUs) * + * @NL80211_MESHCONF_PLINK_TIMEOUT: If no tx activity is seen from a STA we've + * established peering with for longer than this time (in seconds), then + * remove it from the STA's list of peers. Default is 30 minutes. + * * @__NL80211_MESHCONF_ATTR_AFTER_LAST: internal use */ enum nl80211_meshconf_params { @@ -2572,6 +2816,7 @@ enum nl80211_meshconf_params { NL80211_MESHCONF_HWMP_CONFIRMATION_INTERVAL, NL80211_MESHCONF_POWER_MODE, NL80211_MESHCONF_AWAKE_WINDOW, + NL80211_MESHCONF_PLINK_TIMEOUT, /* keep last */ __NL80211_MESHCONF_ATTR_AFTER_LAST, @@ -2619,6 +2864,10 @@ enum nl80211_meshconf_params { * @NL80211_MESH_SETUP_USERSPACE_MPM: Enable this option if userspace will * implement an MPM which handles peer allocation and state. * + * @NL80211_MESH_SETUP_AUTH_PROTOCOL: Inform the kernel of the authentication + * method (u8, as defined in IEEE 8.4.2.100.6, e.g. 0x1 for SAE). + * Default is no authentication method required. + * * @NL80211_MESH_SETUP_ATTR_MAX: highest possible mesh setup attribute number * * @__NL80211_MESH_SETUP_ATTR_AFTER_LAST: Internal use @@ -2632,6 +2881,7 @@ enum nl80211_mesh_setup_params { NL80211_MESH_SETUP_USERSPACE_AMPE, NL80211_MESH_SETUP_ENABLE_VENDOR_SYNC, NL80211_MESH_SETUP_USERSPACE_MPM, + NL80211_MESH_SETUP_AUTH_PROTOCOL, /* keep last */ __NL80211_MESH_SETUP_ATTR_AFTER_LAST, @@ -2712,6 +2962,8 @@ enum nl80211_channel_type { * and %NL80211_ATTR_CENTER_FREQ2 attributes must be provided as well * @NL80211_CHAN_WIDTH_160: 160 MHz channel, the %NL80211_ATTR_CENTER_FREQ1 * attribute must be provided as well + * @NL80211_CHAN_WIDTH_5: 5 MHz OFDM channel + * @NL80211_CHAN_WIDTH_10: 10 MHz OFDM channel */ enum nl80211_chan_width { NL80211_CHAN_WIDTH_20_NOHT, @@ -2720,6 +2972,23 @@ enum nl80211_chan_width { NL80211_CHAN_WIDTH_80, NL80211_CHAN_WIDTH_80P80, NL80211_CHAN_WIDTH_160, + NL80211_CHAN_WIDTH_5, + NL80211_CHAN_WIDTH_10, +}; + +/** + * enum nl80211_bss_scan_width - control channel width for a BSS + * + * These values are used with the %NL80211_BSS_CHAN_WIDTH attribute. + * + * @NL80211_BSS_CHAN_WIDTH_20: control channel is 20 MHz wide or compatible + * @NL80211_BSS_CHAN_WIDTH_10: control channel is 10 MHz wide + * @NL80211_BSS_CHAN_WIDTH_5: control channel is 5 MHz wide + */ +enum nl80211_bss_scan_width { + NL80211_BSS_CHAN_WIDTH_20, + NL80211_BSS_CHAN_WIDTH_10, + NL80211_BSS_CHAN_WIDTH_5, }; /** @@ -2746,6 +3015,8 @@ enum nl80211_chan_width { * @NL80211_BSS_BEACON_IES: binary attribute containing the raw information * elements from a Beacon frame (bin); not present if no Beacon frame has * yet been received + * @NL80211_BSS_CHAN_WIDTH: channel width of the control channel + * (u32, enum nl80211_bss_scan_width) * @__NL80211_BSS_AFTER_LAST: internal * @NL80211_BSS_MAX: highest BSS attribute */ @@ -2762,6 +3033,7 @@ enum nl80211_bss { NL80211_BSS_STATUS, NL80211_BSS_SEEN_MS_AGO, NL80211_BSS_BEACON_IES, + NL80211_BSS_CHAN_WIDTH, /* keep last */ __NL80211_BSS_AFTER_LAST, @@ -2902,21 +3174,43 @@ enum nl80211_key_attributes { * in an array of rates as defined in IEEE 802.11 7.3.2.2 (u8 values with * 1 = 500 kbps) but without the IE length restriction (at most * %NL80211_MAX_SUPP_RATES in a single array). - * @NL80211_TXRATE_MCS: HT (MCS) rates allowed for TX rate selection + * @NL80211_TXRATE_HT: HT (MCS) rates allowed for TX rate selection * in an array of MCS numbers. + * @NL80211_TXRATE_VHT: VHT rates allowed for TX rate selection, + * see &struct nl80211_txrate_vht + * @NL80211_TXRATE_GI: configure GI, see &enum nl80211_txrate_gi * @__NL80211_TXRATE_AFTER_LAST: internal * @NL80211_TXRATE_MAX: highest TX rate attribute */ enum nl80211_tx_rate_attributes { __NL80211_TXRATE_INVALID, NL80211_TXRATE_LEGACY, - NL80211_TXRATE_MCS, + NL80211_TXRATE_HT, + NL80211_TXRATE_VHT, + NL80211_TXRATE_GI, /* keep last */ __NL80211_TXRATE_AFTER_LAST, NL80211_TXRATE_MAX = __NL80211_TXRATE_AFTER_LAST - 1 }; +#define NL80211_TXRATE_MCS NL80211_TXRATE_HT +#define NL80211_VHT_NSS_MAX 8 + +/** + * struct nl80211_txrate_vht - VHT MCS/NSS txrate bitmap + * @mcs: MCS bitmap table for each NSS (array index 0 for 1 stream, etc.) + */ +struct nl80211_txrate_vht { + __u16 mcs[NL80211_VHT_NSS_MAX]; +}; + +enum nl80211_txrate_gi { + NL80211_TXRATE_DEFAULT_GI, + NL80211_TXRATE_FORCE_SGI, + NL80211_TXRATE_FORCE_LGI, +}; + /** * enum nl80211_band - Frequency band * @NL80211_BAND_2GHZ: 2.4 GHz ISM band @@ -3010,11 +3304,11 @@ enum nl80211_tx_power_setting { }; /** - * enum nl80211_wowlan_packet_pattern_attr - WoWLAN packet pattern attribute - * @__NL80211_WOWLAN_PKTPAT_INVALID: invalid number for nested attribute - * @NL80211_WOWLAN_PKTPAT_PATTERN: the pattern, values where the mask has + * enum nl80211_packet_pattern_attr - packet pattern attribute + * @__NL80211_PKTPAT_INVALID: invalid number for nested attribute + * @NL80211_PKTPAT_PATTERN: the pattern, values where the mask has * a zero bit are ignored - * @NL80211_WOWLAN_PKTPAT_MASK: pattern mask, must be long enough to have + * @NL80211_PKTPAT_MASK: pattern mask, must be long enough to have * a bit for each byte in the pattern. The lowest-order bit corresponds * to the first byte of the pattern, but the bytes of the pattern are * in a little-endian-like format, i.e. the 9th byte of the pattern @@ -3025,39 +3319,50 @@ enum nl80211_tx_power_setting { * Note that the pattern matching is done as though frames were not * 802.11 frames but 802.3 frames, i.e. the frame is fully unpacked * first (including SNAP header unpacking) and then matched. - * @NL80211_WOWLAN_PKTPAT_OFFSET: packet offset, pattern is matched after + * @NL80211_PKTPAT_OFFSET: packet offset, pattern is matched after * these fixed number of bytes of received packet - * @NUM_NL80211_WOWLAN_PKTPAT: number of attributes - * @MAX_NL80211_WOWLAN_PKTPAT: max attribute number + * @NUM_NL80211_PKTPAT: number of attributes + * @MAX_NL80211_PKTPAT: max attribute number */ -enum nl80211_wowlan_packet_pattern_attr { - __NL80211_WOWLAN_PKTPAT_INVALID, - NL80211_WOWLAN_PKTPAT_MASK, - NL80211_WOWLAN_PKTPAT_PATTERN, - NL80211_WOWLAN_PKTPAT_OFFSET, - - NUM_NL80211_WOWLAN_PKTPAT, - MAX_NL80211_WOWLAN_PKTPAT = NUM_NL80211_WOWLAN_PKTPAT - 1, +enum nl80211_packet_pattern_attr { + __NL80211_PKTPAT_INVALID, + NL80211_PKTPAT_MASK, + NL80211_PKTPAT_PATTERN, + NL80211_PKTPAT_OFFSET, + + NUM_NL80211_PKTPAT, + MAX_NL80211_PKTPAT = NUM_NL80211_PKTPAT - 1, }; /** - * struct nl80211_wowlan_pattern_support - pattern support information + * struct nl80211_pattern_support - packet pattern support information * @max_patterns: maximum number of patterns supported * @min_pattern_len: minimum length of each pattern * @max_pattern_len: maximum length of each pattern * @max_pkt_offset: maximum Rx packet offset * * This struct is carried in %NL80211_WOWLAN_TRIG_PKT_PATTERN when - * that is part of %NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED in the - * capability information given by the kernel to userspace. + * that is part of %NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED or in + * %NL80211_ATTR_COALESCE_RULE_PKT_PATTERN when that is part of + * %NL80211_ATTR_COALESCE_RULE in the capability information given + * by the kernel to userspace. */ -struct nl80211_wowlan_pattern_support { +struct nl80211_pattern_support { __u32 max_patterns; __u32 min_pattern_len; __u32 max_pattern_len; __u32 max_pkt_offset; } __attribute__((packed)); +/* only for backward compatibility */ +#define __NL80211_WOWLAN_PKTPAT_INVALID __NL80211_PKTPAT_INVALID +#define NL80211_WOWLAN_PKTPAT_MASK NL80211_PKTPAT_MASK +#define NL80211_WOWLAN_PKTPAT_PATTERN NL80211_PKTPAT_PATTERN +#define NL80211_WOWLAN_PKTPAT_OFFSET NL80211_PKTPAT_OFFSET +#define NUM_NL80211_WOWLAN_PKTPAT NUM_NL80211_PKTPAT +#define MAX_NL80211_WOWLAN_PKTPAT MAX_NL80211_PKTPAT +#define nl80211_wowlan_pattern_support nl80211_pattern_support + /** * enum nl80211_wowlan_triggers - WoWLAN trigger definitions * @__NL80211_WOWLAN_TRIG_INVALID: invalid number for nested attributes @@ -3077,7 +3382,7 @@ struct nl80211_wowlan_pattern_support { * pattern matching is done after the packet is converted to the MSDU. * * In %NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED, it is a binary attribute - * carrying a &struct nl80211_wowlan_pattern_support. + * carrying a &struct nl80211_pattern_support. * * When reporting wakeup. it is a u32 attribute containing the 0-based * index of the pattern that caused the wakeup, in the patterns passed @@ -3234,7 +3539,7 @@ struct nl80211_wowlan_tcp_data_token_feature { * @NL80211_WOWLAN_TCP_WAKE_PAYLOAD: wake packet payload, for advertising a * u32 attribute holding the maximum length * @NL80211_WOWLAN_TCP_WAKE_MASK: Wake packet payload mask, not used for - * feature advertising. The mask works like @NL80211_WOWLAN_PKTPAT_MASK + * feature advertising. The mask works like @NL80211_PKTPAT_MASK * but on the TCP payload only. * @NUM_NL80211_WOWLAN_TCP: number of TCP attributes * @MAX_NL80211_WOWLAN_TCP: highest attribute number @@ -3259,6 +3564,55 @@ enum nl80211_wowlan_tcp_attrs { }; /** + * struct nl80211_coalesce_rule_support - coalesce rule support information + * @max_rules: maximum number of rules supported + * @pat: packet pattern support information + * @max_delay: maximum supported coalescing delay in msecs + * + * This struct is carried in %NL80211_ATTR_COALESCE_RULE in the + * capability information given by the kernel to userspace. + */ +struct nl80211_coalesce_rule_support { + __u32 max_rules; + struct nl80211_pattern_support pat; + __u32 max_delay; +} __attribute__((packed)); + +/** + * enum nl80211_attr_coalesce_rule - coalesce rule attribute + * @__NL80211_COALESCE_RULE_INVALID: invalid number for nested attribute + * @NL80211_ATTR_COALESCE_RULE_DELAY: delay in msecs used for packet coalescing + * @NL80211_ATTR_COALESCE_RULE_CONDITION: condition for packet coalescence, + * see &enum nl80211_coalesce_condition. + * @NL80211_ATTR_COALESCE_RULE_PKT_PATTERN: packet offset, pattern is matched + * after these fixed number of bytes of received packet + * @NUM_NL80211_ATTR_COALESCE_RULE: number of attributes + * @NL80211_ATTR_COALESCE_RULE_MAX: max attribute number + */ +enum nl80211_attr_coalesce_rule { + __NL80211_COALESCE_RULE_INVALID, + NL80211_ATTR_COALESCE_RULE_DELAY, + NL80211_ATTR_COALESCE_RULE_CONDITION, + NL80211_ATTR_COALESCE_RULE_PKT_PATTERN, + + /* keep last */ + NUM_NL80211_ATTR_COALESCE_RULE, + NL80211_ATTR_COALESCE_RULE_MAX = NUM_NL80211_ATTR_COALESCE_RULE - 1 +}; + +/** + * enum nl80211_coalesce_condition - coalesce rule conditions + * @NL80211_COALESCE_CONDITION_MATCH: coalaesce Rx packets when patterns + * in a rule are matched. + * @NL80211_COALESCE_CONDITION_NO_MATCH: coalesce Rx packets when patterns + * in a rule are not matched. + */ +enum nl80211_coalesce_condition { + NL80211_COALESCE_CONDITION_MATCH, + NL80211_COALESCE_CONDITION_NO_MATCH +}; + +/** * enum nl80211_iface_limit_attrs - limit attributes * @NL80211_IFACE_LIMIT_UNSPEC: (reserved) * @NL80211_IFACE_LIMIT_MAX: maximum number of interfaces that @@ -3502,11 +3856,6 @@ enum nl80211_ap_sme_features { * @NL80211_FEATURE_CELL_BASE_REG_HINTS: This driver has been tested * to work properly to suppport receiving regulatory hints from * cellular base stations. - * @NL80211_FEATURE_P2P_DEVICE_NEEDS_CHANNEL: If this is set, an active - * P2P Device (%NL80211_IFTYPE_P2P_DEVICE) requires its own channel - * in the interface combinations, even when it's only used for scan - * and remain-on-channel. This could be due to, for example, the - * remain-on-channel implementation requiring a channel context. * @NL80211_FEATURE_SAE: This driver supports simultaneous authentication of * equals (SAE) with user space SME (NL80211_CMD_AUTHENTICATE) in station * mode @@ -3538,13 +3887,17 @@ enum nl80211_ap_sme_features { * Peering Management entity which may be implemented by registering for * beacons or NL80211_CMD_NEW_PEER_CANDIDATE events. The mesh beacon is * still generated by the driver. + * @NL80211_FEATURE_ACTIVE_MONITOR: This driver supports an active monitor + * interface. An active monitor interface behaves like a normal monitor + * interface, but gets added to the driver. It ensures that incoming + * unicast packets directed at the configured interface address get ACKed. */ enum nl80211_feature_flags { NL80211_FEATURE_SK_TX_STATUS = 1 << 0, NL80211_FEATURE_HT_IBSS = 1 << 1, NL80211_FEATURE_INACTIVITY_TIMER = 1 << 2, NL80211_FEATURE_CELL_BASE_REG_HINTS = 1 << 3, - NL80211_FEATURE_P2P_DEVICE_NEEDS_CHANNEL = 1 << 4, + /* bit 4 is reserved - don't use */ NL80211_FEATURE_SAE = 1 << 5, NL80211_FEATURE_LOW_PRIORITY_SCAN = 1 << 6, NL80211_FEATURE_SCAN_FLUSH = 1 << 7, @@ -3557,6 +3910,7 @@ enum nl80211_feature_flags { NL80211_FEATURE_ADVERTISE_CHAN_LIMITS = 1 << 14, NL80211_FEATURE_FULL_AP_CLIENT_STATE = 1 << 15, NL80211_FEATURE_USERSPACE_MPM = 1 << 16, + NL80211_FEATURE_ACTIVE_MONITOR = 1 << 17, }; /** @@ -3657,13 +4011,12 @@ enum nl80211_radar_event { * * Channel states used by the DFS code. * - * @IEEE80211_DFS_USABLE: The channel can be used, but channel availability + * @NL80211_DFS_USABLE: The channel can be used, but channel availability * check (CAC) must be performed before using it for AP or IBSS. - * @IEEE80211_DFS_UNAVAILABLE: A radar has been detected on this channel, it + * @NL80211_DFS_UNAVAILABLE: A radar has been detected on this channel, it * is therefore marked as not available. - * @IEEE80211_DFS_AVAILABLE: The channel has been CAC checked and is available. + * @NL80211_DFS_AVAILABLE: The channel has been CAC checked and is available. */ - enum nl80211_dfs_state { NL80211_DFS_USABLE, NL80211_DFS_UNAVAILABLE, @@ -3682,4 +4035,72 @@ enum nl80211_protocol_features { NL80211_PROTOCOL_FEATURE_SPLIT_WIPHY_DUMP = 1 << 0, }; +/** + * enum nl80211_crit_proto_id - nl80211 critical protocol identifiers + * + * @NL80211_CRIT_PROTO_UNSPEC: protocol unspecified. + * @NL80211_CRIT_PROTO_DHCP: BOOTP or DHCPv6 protocol. + * @NL80211_CRIT_PROTO_EAPOL: EAPOL protocol. + * @NL80211_CRIT_PROTO_APIPA: APIPA protocol. + * @NUM_NL80211_CRIT_PROTO: must be kept last. + */ +enum nl80211_crit_proto_id { + NL80211_CRIT_PROTO_UNSPEC, + NL80211_CRIT_PROTO_DHCP, + NL80211_CRIT_PROTO_EAPOL, + NL80211_CRIT_PROTO_APIPA, + /* add other protocols before this one */ + NUM_NL80211_CRIT_PROTO +}; + +/* maximum duration for critical protocol measures */ +#define NL80211_CRIT_PROTO_MAX_DURATION 5000 /* msec */ + +/** + * enum nl80211_rxmgmt_flags - flags for received management frame. + * + * Used by cfg80211_rx_mgmt() + * + * @NL80211_RXMGMT_FLAG_ANSWERED: frame was answered by device/driver. + */ +enum nl80211_rxmgmt_flags { + NL80211_RXMGMT_FLAG_ANSWERED = 1 << 0, +}; + +/* + * If this flag is unset, the lower 24 bits are an OUI, if set + * a Linux nl80211 vendor ID is used (no such IDs are allocated + * yet, so that's not valid so far) + */ +#define NL80211_VENDOR_ID_IS_LINUX 0x80000000 + +/** + * struct nl80211_vendor_cmd_info - vendor command data + * @vendor_id: If the %NL80211_VENDOR_ID_IS_LINUX flag is clear, then the + * value is a 24-bit OUI; if it is set then a separately allocated ID + * may be used, but no such IDs are allocated yet. New IDs should be + * added to this file when needed. + * @subcmd: sub-command ID for the command + */ +struct nl80211_vendor_cmd_info { + __u32 vendor_id; + __u32 subcmd; +}; + +/** + * enum nl80211_tdls_peer_capability - TDLS peer flags. + * + * Used by tdls_mgmt() to determine which conditional elements need + * to be added to TDLS Setup frames. + * + * @NL80211_TDLS_PEER_HT: TDLS peer is HT capable. + * @NL80211_TDLS_PEER_VHT: TDLS peer is VHT capable. + * @NL80211_TDLS_PEER_WMM: TDLS peer is WMM capable. + */ +enum nl80211_tdls_peer_capability { + NL80211_TDLS_PEER_HT = 1<<0, + NL80211_TDLS_PEER_VHT = 1<<1, + NL80211_TDLS_PEER_WMM = 1<<2, +}; + #endif /* __LINUX_NL80211_H */ diff --git a/reglib.h b/reglib.h index d570c36..afd5ef6 100644 --- a/reglib.h +++ b/reglib.h @@ -37,9 +37,6 @@ struct ieee80211_regdomain { struct ieee80211_reg_rule reg_rules[]; }; -/* Remove this once upstream nl80211.h gets this */ -#define NL80211_RRF_NO_IR (1<<7) - #define REGLIB_MHZ_TO_KHZ(freq) ((freq) * 1000) #define REGLIB_KHZ_TO_MHZ(freq) ((freq) / 1000) #define REGLIB_DBI_TO_MBI(gain) ((gain) * 100) -- 1.7.9.5 _______________________________________________ wireless-regdb mailing list wireless-regdb@lists.infradead.org http://lists.infradead.org/mailman/listinfo/wireless-regdb ^ permalink raw reply related [flat|nested] 13+ messages in thread
* [PATCH 2/2] crda: add AUTO-BW rule flag support 2014-05-09 8:38 ` [wireless-regdb] " Janusz Dziedzic @ 2014-05-09 8:38 ` Janusz Dziedzic -1 siblings, 0 replies; 13+ messages in thread From: Janusz Dziedzic @ 2014-05-09 8:38 UTC (permalink / raw) To: wireless-regdb; +Cc: linux-wireless, mcgrof, Janusz Dziedzic Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com> --- regdb.h | 1 + reglib.c | 4 ++++ 2 files changed, 5 insertions(+) diff --git a/regdb.h b/regdb.h index 20f29e9..3ffb781 100644 --- a/regdb.h +++ b/regdb.h @@ -81,6 +81,7 @@ enum reg_rule_flags { * Point links */ RRF_NO_IR = 1<<7, /* do not initiate radiation */ __RRF_NO_IBSS = 1<<8, /* old no-IBSS rule, maps to no-ir */ + RRF_AUTO_BW = 1<<11, /* Auto BW calculations */ }; #define RRF_NO_IR_ALL (RRF_NO_IR | __RRF_NO_IBSS) diff --git a/reglib.c b/reglib.c index 1e57634..3deca4a 100644 --- a/reglib.c +++ b/reglib.c @@ -750,6 +750,8 @@ static void print_reg_rule(const struct ieee80211_reg_rule *rule) printf(", PTMP-ONLY"); if (rule->flags & RRF_NO_IR_ALL) printf(", NO-IR"); + if (rule->flags & RRF_AUTO_BW) + printf(", AUTO-BW"); printf("\n"); } @@ -793,6 +795,8 @@ static uint32_t reglib_parse_rule_flag(char *flag_s) return RRF_PTMP_ONLY; if (strncmp(flag_s, "NO-IR", 5) == 0) return RRF_NO_IR; + if (strncmp(flag_s, "AUTO-BW", 7) == 0) + return RRF_AUTO_BW; return 0; } -- 1.7.9.5 ^ permalink raw reply related [flat|nested] 13+ messages in thread
* [wireless-regdb] [PATCH 2/2] crda: add AUTO-BW rule flag support @ 2014-05-09 8:38 ` Janusz Dziedzic 0 siblings, 0 replies; 13+ messages in thread From: Janusz Dziedzic @ 2014-05-09 8:38 UTC (permalink / raw) To: wireless-regdb; +Cc: Janusz Dziedzic, linux-wireless, mcgrof Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com> --- regdb.h | 1 + reglib.c | 4 ++++ 2 files changed, 5 insertions(+) diff --git a/regdb.h b/regdb.h index 20f29e9..3ffb781 100644 --- a/regdb.h +++ b/regdb.h @@ -81,6 +81,7 @@ enum reg_rule_flags { * Point links */ RRF_NO_IR = 1<<7, /* do not initiate radiation */ __RRF_NO_IBSS = 1<<8, /* old no-IBSS rule, maps to no-ir */ + RRF_AUTO_BW = 1<<11, /* Auto BW calculations */ }; #define RRF_NO_IR_ALL (RRF_NO_IR | __RRF_NO_IBSS) diff --git a/reglib.c b/reglib.c index 1e57634..3deca4a 100644 --- a/reglib.c +++ b/reglib.c @@ -750,6 +750,8 @@ static void print_reg_rule(const struct ieee80211_reg_rule *rule) printf(", PTMP-ONLY"); if (rule->flags & RRF_NO_IR_ALL) printf(", NO-IR"); + if (rule->flags & RRF_AUTO_BW) + printf(", AUTO-BW"); printf("\n"); } @@ -793,6 +795,8 @@ static uint32_t reglib_parse_rule_flag(char *flag_s) return RRF_PTMP_ONLY; if (strncmp(flag_s, "NO-IR", 5) == 0) return RRF_NO_IR; + if (strncmp(flag_s, "AUTO-BW", 7) == 0) + return RRF_AUTO_BW; return 0; } -- 1.7.9.5 _______________________________________________ wireless-regdb mailing list wireless-regdb@lists.infradead.org http://lists.infradead.org/mailman/listinfo/wireless-regdb ^ permalink raw reply related [flat|nested] 13+ messages in thread
* Re: [PATCH 2/2] crda: add AUTO-BW rule flag support 2014-05-09 8:38 ` [wireless-regdb] " Janusz Dziedzic @ 2014-06-10 21:52 ` Luis R. Rodriguez -1 siblings, 0 replies; 13+ messages in thread From: Luis R. Rodriguez @ 2014-06-10 21:52 UTC (permalink / raw) To: Janusz Dziedzic; +Cc: wireless-regdb@lists.infradead.org, linux-wireless On Fri, May 9, 2014 at 1:38 AM, Janusz Dziedzic <janusz.dziedzic@tieto.com> wrote: > Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com> Applied and pushed, thanks. Luis ^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [wireless-regdb] [PATCH 2/2] crda: add AUTO-BW rule flag support @ 2014-06-10 21:52 ` Luis R. Rodriguez 0 siblings, 0 replies; 13+ messages in thread From: Luis R. Rodriguez @ 2014-06-10 21:52 UTC (permalink / raw) To: Janusz Dziedzic; +Cc: linux-wireless, wireless-regdb@lists.infradead.org On Fri, May 9, 2014 at 1:38 AM, Janusz Dziedzic <janusz.dziedzic@tieto.com> wrote: > Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com> Applied and pushed, thanks. Luis _______________________________________________ wireless-regdb mailing list wireless-regdb@lists.infradead.org http://lists.infradead.org/mailman/listinfo/wireless-regdb ^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH] wireless-regdb: add AUTO-BW rule flag 2014-05-09 8:38 ` [wireless-regdb] " Janusz Dziedzic @ 2014-05-20 7:59 ` Luis R. Rodriguez -1 siblings, 0 replies; 13+ messages in thread From: Luis R. Rodriguez @ 2014-05-20 7:59 UTC (permalink / raw) To: Janusz Dziedzic; +Cc: wireless-regdb@lists.infradead.org, linux-wireless On Fri, May 9, 2014 at 1:38 AM, Janusz Dziedzic <janusz.dziedzic@tieto.com> wrote: > Sync with latest nl80211.h and add AUTO-BW flag. > If this flag set, maximum available bandwidth should > be calculated base on contiguous rules and wider channels > will be allowed to cross multiple contiguous/overlapping > frequency ranges. > > Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com> Once John merges this I'll merge on CRDA, just as with the DFS CAC patch, please do let me know if and when that happens. Luis ^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [wireless-regdb] [PATCH] wireless-regdb: add AUTO-BW rule flag @ 2014-05-20 7:59 ` Luis R. Rodriguez 0 siblings, 0 replies; 13+ messages in thread From: Luis R. Rodriguez @ 2014-05-20 7:59 UTC (permalink / raw) To: Janusz Dziedzic; +Cc: linux-wireless, wireless-regdb@lists.infradead.org On Fri, May 9, 2014 at 1:38 AM, Janusz Dziedzic <janusz.dziedzic@tieto.com> wrote: > Sync with latest nl80211.h and add AUTO-BW flag. > If this flag set, maximum available bandwidth should > be calculated base on contiguous rules and wider channels > will be allowed to cross multiple contiguous/overlapping > frequency ranges. > > Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com> Once John merges this I'll merge on CRDA, just as with the DFS CAC patch, please do let me know if and when that happens. Luis _______________________________________________ wireless-regdb mailing list wireless-regdb@lists.infradead.org http://lists.infradead.org/mailman/listinfo/wireless-regdb ^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH] wireless-regdb: add AUTO-BW rule flag 2014-05-20 7:59 ` [wireless-regdb] " Luis R. Rodriguez @ 2014-05-20 14:06 ` John W. Linville -1 siblings, 0 replies; 13+ messages in thread From: John W. Linville @ 2014-05-20 14:06 UTC (permalink / raw) To: Luis R. Rodriguez Cc: Janusz Dziedzic, wireless-regdb@lists.infradead.org, linux-wireless On Tue, May 20, 2014 at 12:59:29AM -0700, Luis R. Rodriguez wrote: > On Fri, May 9, 2014 at 1:38 AM, Janusz Dziedzic > <janusz.dziedzic@tieto.com> wrote: > > Sync with latest nl80211.h and add AUTO-BW flag. > > If this flag set, maximum available bandwidth should > > be calculated base on contiguous rules and wider channels > > will be allowed to cross multiple contiguous/overlapping > > frequency ranges. > > > > Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com> > > Once John merges this I'll merge on CRDA, just as with the DFS CAC > patch, please do let me know if and when that happens. I just merged this yesterday: commit e90f7a95b9c646b398d56cfe381bf1cc3508d96e Author: Janusz Dziedzic <janusz.dziedzic@tieto.com> Date: Tue Feb 25 08:21:18 2014 +0100 wireless-regdb: add AUTO-BW rule flag Sync with latest nl80211.h and add AUTO-BW flag. If this flag set, maximum available bandwidth should be calculated base on contiguous rules and wider channels will be allowed to cross multiple contiguous/overlapping frequency ranges. Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> -- John W. Linville Someday the world will need a hero, and you linville@tuxdriver.com might be all we have. Be ready. ^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [wireless-regdb] [PATCH] wireless-regdb: add AUTO-BW rule flag @ 2014-05-20 14:06 ` John W. Linville 0 siblings, 0 replies; 13+ messages in thread From: John W. Linville @ 2014-05-20 14:06 UTC (permalink / raw) To: Luis R. Rodriguez Cc: Janusz Dziedzic, linux-wireless, wireless-regdb@lists.infradead.org On Tue, May 20, 2014 at 12:59:29AM -0700, Luis R. Rodriguez wrote: > On Fri, May 9, 2014 at 1:38 AM, Janusz Dziedzic > <janusz.dziedzic@tieto.com> wrote: > > Sync with latest nl80211.h and add AUTO-BW flag. > > If this flag set, maximum available bandwidth should > > be calculated base on contiguous rules and wider channels > > will be allowed to cross multiple contiguous/overlapping > > frequency ranges. > > > > Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com> > > Once John merges this I'll merge on CRDA, just as with the DFS CAC > patch, please do let me know if and when that happens. I just merged this yesterday: commit e90f7a95b9c646b398d56cfe381bf1cc3508d96e Author: Janusz Dziedzic <janusz.dziedzic@tieto.com> Date: Tue Feb 25 08:21:18 2014 +0100 wireless-regdb: add AUTO-BW rule flag Sync with latest nl80211.h and add AUTO-BW flag. If this flag set, maximum available bandwidth should be calculated base on contiguous rules and wider channels will be allowed to cross multiple contiguous/overlapping frequency ranges. Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> -- John W. Linville Someday the world will need a hero, and you linville@tuxdriver.com might be all we have. Be ready. _______________________________________________ wireless-regdb mailing list wireless-regdb@lists.infradead.org http://lists.infradead.org/mailman/listinfo/wireless-regdb ^ permalink raw reply [flat|nested] 13+ messages in thread
* [PATCH] wireless-regdb: add AUTO-BW rule flag @ 2014-02-25 7:21 Janusz Dziedzic 0 siblings, 0 replies; 13+ messages in thread From: Janusz Dziedzic @ 2014-02-25 7:21 UTC (permalink / raw) To: wireless-regdb Cc: linux-wireless, johannes, mcgrof, linville, Janusz Dziedzic Sync with latest nl80211.h and add AUTO-BW flag. If this flag set, maximum available bandwidth should be calculated base on contiguous rules and wider channels will be allowed to cross multiple contiguous/overlapping frequency ranges. Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com> --- dbparse.py | 1 + 1 file changed, 1 insertion(+) diff --git a/dbparse.py b/dbparse.py index ac7234b..b735b6a 100755 --- a/dbparse.py +++ b/dbparse.py @@ -16,6 +16,7 @@ flag_definitions = { # hole at bit 8 # hole at bit 9. FIXME: Where is NO-HT40 defined? 'NO-HT40': 1<<10, + 'AUTO-BW': 1<<11, } dfs_regions = { -- 1.7.9.5 ^ permalink raw reply related [flat|nested] 13+ messages in thread
end of thread, other threads:[~2014-06-10 21:52 UTC | newest] Thread overview: 13+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2014-05-09 8:38 [PATCH] wireless-regdb: add AUTO-BW rule flag Janusz Dziedzic 2014-05-09 8:38 ` [wireless-regdb] " Janusz Dziedzic 2014-05-09 8:38 ` [PATCH 1/2] crda: sync with latest nl80211.h Janusz Dziedzic 2014-05-09 8:38 ` [wireless-regdb] " Janusz Dziedzic 2014-05-09 8:38 ` [PATCH 2/2] crda: add AUTO-BW rule flag support Janusz Dziedzic 2014-05-09 8:38 ` [wireless-regdb] " Janusz Dziedzic 2014-06-10 21:52 ` Luis R. Rodriguez 2014-06-10 21:52 ` [wireless-regdb] " Luis R. Rodriguez 2014-05-20 7:59 ` [PATCH] wireless-regdb: add AUTO-BW rule flag Luis R. Rodriguez 2014-05-20 7:59 ` [wireless-regdb] " Luis R. Rodriguez 2014-05-20 14:06 ` John W. Linville 2014-05-20 14:06 ` [wireless-regdb] " John W. Linville -- strict thread matches above, loose matches on Subject: below -- 2014-02-25 7:21 Janusz Dziedzic
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.