* [PATCH v2 0/3] ARM: dts: sun7i: Add Banana Pi board @ 2014-10-01 7:26 ` Hans de Goede 0 siblings, 0 replies; 10+ messages in thread From: Hans de Goede @ 2014-10-01 7:26 UTC (permalink / raw) To: linux-arm-kernel Hi Maxime, Here is v2 of the Bananapi board addition. Sorry for taking so long. Changes from v2: -Move uart3_pins definition from a20-sun7i-bananapi.dts to a20-sun7i.dtsi, the addition of the pinctrl node is done in a separate patch -Use the new dual license header as license header Regards, Hans ^ permalink raw reply [flat|nested] 10+ messages in thread
* [PATCH v2 0/3] ARM: dts: sun7i: Add Banana Pi board @ 2014-10-01 7:26 ` Hans de Goede 0 siblings, 0 replies; 10+ messages in thread From: Hans de Goede @ 2014-10-01 7:26 UTC (permalink / raw) To: Maxime Ripard Cc: Ian Campbell, Karsten Merker, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, devicetree, linux-sunxi-/JYPxA39Uh5TLH3MbocFFw Hi Maxime, Here is v2 of the Bananapi board addition. Sorry for taking so long. Changes from v2: -Move uart3_pins definition from a20-sun7i-bananapi.dts to a20-sun7i.dtsi, the addition of the pinctrl node is done in a separate patch -Use the new dual license header as license header Regards, Hans ^ permalink raw reply [flat|nested] 10+ messages in thread
* [PATCH v2 1/3] ARM: dts: sun7i: Add spi0_pins_a pinctrl setting @ 2014-10-01 7:26 ` Hans de Goede 0 siblings, 0 replies; 10+ messages in thread From: Hans de Goede @ 2014-10-01 7:26 UTC (permalink / raw) To: linux-arm-kernel Signed-off-by: Hans de Goede <hdegoede@redhat.com> --- arch/arm/boot/dts/sun7i-a20.dtsi | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/arch/arm/boot/dts/sun7i-a20.dtsi b/arch/arm/boot/dts/sun7i-a20.dtsi index b22daf3..cb5abef 100644 --- a/arch/arm/boot/dts/sun7i-a20.dtsi +++ b/arch/arm/boot/dts/sun7i-a20.dtsi @@ -784,6 +784,13 @@ allwinner,pull = <0>; }; + spi0_pins_a: spi0 at 0 { + allwinner,pins = "PI10", "PI11", "PI12", "PI13", "PI14"; + allwinner,function = "spi0"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + spi1_pins_a: spi1 at 0 { allwinner,pins = "PI16", "PI17", "PI18", "PI19"; allwinner,function = "spi1"; -- 2.1.0 ^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH v2 1/3] ARM: dts: sun7i: Add spi0_pins_a pinctrl setting @ 2014-10-01 7:26 ` Hans de Goede 0 siblings, 0 replies; 10+ messages in thread From: Hans de Goede @ 2014-10-01 7:26 UTC (permalink / raw) To: Maxime Ripard Cc: Ian Campbell, Karsten Merker, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, devicetree, linux-sunxi-/JYPxA39Uh5TLH3MbocFFw, Hans de Goede Signed-off-by: Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org> --- arch/arm/boot/dts/sun7i-a20.dtsi | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/arch/arm/boot/dts/sun7i-a20.dtsi b/arch/arm/boot/dts/sun7i-a20.dtsi index b22daf3..cb5abef 100644 --- a/arch/arm/boot/dts/sun7i-a20.dtsi +++ b/arch/arm/boot/dts/sun7i-a20.dtsi @@ -784,6 +784,13 @@ allwinner,pull = <0>; }; + spi0_pins_a: spi0@0 { + allwinner,pins = "PI10", "PI11", "PI12", "PI13", "PI14"; + allwinner,function = "spi0"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + spi1_pins_a: spi1@0 { allwinner,pins = "PI16", "PI17", "PI18", "PI19"; allwinner,function = "spi1"; -- 2.1.0 ^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH v2 2/3] ARM: dts: sun7i: Add uart3_pins_b pinctrl setting @ 2014-10-01 7:26 ` Hans de Goede 0 siblings, 0 replies; 10+ messages in thread From: Hans de Goede @ 2014-10-01 7:26 UTC (permalink / raw) To: linux-arm-kernel The uart3_pins_a multiplexes the uart3 pins to port G, add a pinctrl entry for mapping them to port H (as used on the Bananapi). Signed-off-by: Hans de Goede <hdegoede@redhat.com> --- arch/arm/boot/dts/sun7i-a20.dtsi | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/arch/arm/boot/dts/sun7i-a20.dtsi b/arch/arm/boot/dts/sun7i-a20.dtsi index cb5abef..302dc1f 100644 --- a/arch/arm/boot/dts/sun7i-a20.dtsi +++ b/arch/arm/boot/dts/sun7i-a20.dtsi @@ -677,6 +677,13 @@ allwinner,pull = <0>; }; + uart3_pins_b: uart3 at 1 { + allwinner,pins = "PH0", "PH1"; + allwinner,function = "uart3"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + uart4_pins_a: uart4 at 0 { allwinner,pins = "PG10", "PG11"; allwinner,function = "uart4"; -- 2.1.0 ^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH v2 2/3] ARM: dts: sun7i: Add uart3_pins_b pinctrl setting @ 2014-10-01 7:26 ` Hans de Goede 0 siblings, 0 replies; 10+ messages in thread From: Hans de Goede @ 2014-10-01 7:26 UTC (permalink / raw) To: Maxime Ripard Cc: Ian Campbell, Karsten Merker, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, devicetree, linux-sunxi-/JYPxA39Uh5TLH3MbocFFw, Hans de Goede The uart3_pins_a multiplexes the uart3 pins to port G, add a pinctrl entry for mapping them to port H (as used on the Bananapi). Signed-off-by: Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org> --- arch/arm/boot/dts/sun7i-a20.dtsi | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/arch/arm/boot/dts/sun7i-a20.dtsi b/arch/arm/boot/dts/sun7i-a20.dtsi index cb5abef..302dc1f 100644 --- a/arch/arm/boot/dts/sun7i-a20.dtsi +++ b/arch/arm/boot/dts/sun7i-a20.dtsi @@ -677,6 +677,13 @@ allwinner,pull = <0>; }; + uart3_pins_b: uart3@1 { + allwinner,pins = "PH0", "PH1"; + allwinner,function = "uart3"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + uart4_pins_a: uart4@0 { allwinner,pins = "PG10", "PG11"; allwinner,function = "uart4"; -- 2.1.0 ^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH v2 3/3] ARM: dts: sun7i: Add Banana Pi board @ 2014-10-01 7:26 ` Hans de Goede 0 siblings, 0 replies; 10+ messages in thread From: Hans de Goede @ 2014-10-01 7:26 UTC (permalink / raw) To: linux-arm-kernel The Banana Pi is an A20 based development board using Raspberry Pi compatible IO headers. It comes with 1 GB RAM, 1 Gb ethernet, 2x USB host, sata, hdmi and stereo audio out + various expenansion headers: http://www.lemaker.org/ Signed-off-by: Hans de Goede <hdegoede@redhat.com> --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/sun7i-a20-bananapi.dts | 214 +++++++++++++++++++++++++++++++ 2 files changed, 215 insertions(+) create mode 100644 arch/arm/boot/dts/sun7i-a20-bananapi.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index b8c5cd3..c3003a4 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -414,6 +414,7 @@ dtb-$(CONFIG_MACH_SUN6I) += \ sun6i-a31-hummingbird.dtb \ sun6i-a31-m9.dtb dtb-$(CONFIG_MACH_SUN7I) += \ + sun7i-a20-bananapi.dtb \ sun7i-a20-cubieboard2.dtb \ sun7i-a20-cubietruck.dtb \ sun7i-a20-i12-tvbox.dtb \ diff --git a/arch/arm/boot/dts/sun7i-a20-bananapi.dts b/arch/arm/boot/dts/sun7i-a20-bananapi.dts new file mode 100644 index 0000000..0e7c9f5 --- /dev/null +++ b/arch/arm/boot/dts/sun7i-a20-bananapi.dts @@ -0,0 +1,214 @@ +/* + * Copyright 2014 Hans de Goede <hdegoede@redhat.com> + * + * Hans de Goede <hdegoede@redhat.com> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This library is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This library is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public + * License along with this library; if not, write to the Free + * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, + * MA 02110-1301 USA + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +/include/ "sun7i-a20.dtsi" +/include/ "sunxi-common-regulators.dtsi" + +/ { + model = "LeMaker Banana Pi"; + compatible = "lemaker,bananapi", "allwinner,sun7i-a20"; + + soc at 01c00000 { + spi0: spi at 01c05000 { + pinctrl-names = "default"; + pinctrl-0 = <&spi0_pins_a>; + status = "okay"; + }; + + mmc0: mmc at 01c0f000 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_bananapi>; + vmmc-supply = <®_vcc3v3>; + bus-width = <4>; + cd-gpios = <&pio 7 10 0>; /* PH10 */ + cd-inverted; + status = "okay"; + }; + + usbphy: phy at 01c13400 { + usb1_vbus-supply = <®_usb1_vbus>; + usb2_vbus-supply = <®_usb2_vbus>; + status = "okay"; + }; + + ehci0: usb at 01c14000 { + status = "okay"; + }; + + ohci0: usb at 01c14400 { + status = "okay"; + }; + + ahci: sata at 01c18000 { + status = "okay"; + }; + + ehci1: usb at 01c1c000 { + status = "okay"; + }; + + ohci1: usb at 01c1c400 { + status = "okay"; + }; + + pinctrl at 01c20800 { + mmc0_cd_pin_bananapi: mmc0_cd_pin at 0 { + allwinner,pins = "PH10"; + allwinner,function = "gpio_in"; + allwinner,drive = <0>; + allwinner,pull = <1>; + }; + + gmac_power_pin_bananapi: gmac_power_pin at 0 { + allwinner,pins = "PH23"; + allwinner,function = "gpio_out"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + + led_pins_bananapi: led_pins at 0 { + allwinner,pins = "PH24"; + allwinner,function = "gpio_out"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + }; + + ir0: ir at 01c21800 { + pinctrl-names = "default"; + pinctrl-0 = <&ir0_pins_a>; + status = "okay"; + }; + + uart0: serial at 01c28000 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins_a>; + status = "okay"; + }; + + uart3: serial at 01c28c00 { + pinctrl-names = "default"; + pinctrl-0 = <&uart3_pins_b>; + status = "okay"; + }; + + uart7: serial at 01c29c00 { + pinctrl-names = "default"; + pinctrl-0 = <&uart7_pins_a>; + status = "okay"; + }; + + i2c0: i2c at 01c2ac00 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins_a>; + status = "okay"; + + axp209: pmic at 34 { + compatible = "x-powers,axp209"; + reg = <0x34>; + interrupt-parent = <&nmi_intc>; + interrupts = <0 8>; + + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + + i2c2: i2c at 01c2b400 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins_a>; + status = "okay"; + }; + + gmac: ethernet at 01c50000 { + pinctrl-names = "default"; + pinctrl-0 = <&gmac_pins_rgmii_a>; + phy = <&phy1>; + phy-mode = "rgmii"; + phy-supply = <®_gmac_3v3>; + status = "okay"; + + phy1: ethernet-phy at 1 { + reg = <1>; + }; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&led_pins_bananapi>; + + green { + label = "bananapi:green:usr"; + gpios = <&pio 7 24 0>; + }; + }; + + reg_usb1_vbus: usb1-vbus { + status = "okay"; + }; + + reg_usb2_vbus: usb2-vbus { + status = "okay"; + }; + + reg_gmac_3v3: gmac-3v3 { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&gmac_power_pin_bananapi>; + regulator-name = "gmac-3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + startup-delay-us = <50000>; + enable-active-high; + gpio = <&pio 7 23 0>; + }; +}; -- 2.1.0 ^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH v2 3/3] ARM: dts: sun7i: Add Banana Pi board @ 2014-10-01 7:26 ` Hans de Goede 0 siblings, 0 replies; 10+ messages in thread From: Hans de Goede @ 2014-10-01 7:26 UTC (permalink / raw) To: Maxime Ripard Cc: Ian Campbell, Karsten Merker, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, devicetree, linux-sunxi-/JYPxA39Uh5TLH3MbocFFw, Hans de Goede The Banana Pi is an A20 based development board using Raspberry Pi compatible IO headers. It comes with 1 GB RAM, 1 Gb ethernet, 2x USB host, sata, hdmi and stereo audio out + various expenansion headers: http://www.lemaker.org/ Signed-off-by: Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org> --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/sun7i-a20-bananapi.dts | 214 +++++++++++++++++++++++++++++++ 2 files changed, 215 insertions(+) create mode 100644 arch/arm/boot/dts/sun7i-a20-bananapi.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index b8c5cd3..c3003a4 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -414,6 +414,7 @@ dtb-$(CONFIG_MACH_SUN6I) += \ sun6i-a31-hummingbird.dtb \ sun6i-a31-m9.dtb dtb-$(CONFIG_MACH_SUN7I) += \ + sun7i-a20-bananapi.dtb \ sun7i-a20-cubieboard2.dtb \ sun7i-a20-cubietruck.dtb \ sun7i-a20-i12-tvbox.dtb \ diff --git a/arch/arm/boot/dts/sun7i-a20-bananapi.dts b/arch/arm/boot/dts/sun7i-a20-bananapi.dts new file mode 100644 index 0000000..0e7c9f5 --- /dev/null +++ b/arch/arm/boot/dts/sun7i-a20-bananapi.dts @@ -0,0 +1,214 @@ +/* + * Copyright 2014 Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org> + * + * Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This library is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This library is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public + * License along with this library; if not, write to the Free + * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, + * MA 02110-1301 USA + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +/include/ "sun7i-a20.dtsi" +/include/ "sunxi-common-regulators.dtsi" + +/ { + model = "LeMaker Banana Pi"; + compatible = "lemaker,bananapi", "allwinner,sun7i-a20"; + + soc@01c00000 { + spi0: spi@01c05000 { + pinctrl-names = "default"; + pinctrl-0 = <&spi0_pins_a>; + status = "okay"; + }; + + mmc0: mmc@01c0f000 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_bananapi>; + vmmc-supply = <®_vcc3v3>; + bus-width = <4>; + cd-gpios = <&pio 7 10 0>; /* PH10 */ + cd-inverted; + status = "okay"; + }; + + usbphy: phy@01c13400 { + usb1_vbus-supply = <®_usb1_vbus>; + usb2_vbus-supply = <®_usb2_vbus>; + status = "okay"; + }; + + ehci0: usb@01c14000 { + status = "okay"; + }; + + ohci0: usb@01c14400 { + status = "okay"; + }; + + ahci: sata@01c18000 { + status = "okay"; + }; + + ehci1: usb@01c1c000 { + status = "okay"; + }; + + ohci1: usb@01c1c400 { + status = "okay"; + }; + + pinctrl@01c20800 { + mmc0_cd_pin_bananapi: mmc0_cd_pin@0 { + allwinner,pins = "PH10"; + allwinner,function = "gpio_in"; + allwinner,drive = <0>; + allwinner,pull = <1>; + }; + + gmac_power_pin_bananapi: gmac_power_pin@0 { + allwinner,pins = "PH23"; + allwinner,function = "gpio_out"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + + led_pins_bananapi: led_pins@0 { + allwinner,pins = "PH24"; + allwinner,function = "gpio_out"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + }; + + ir0: ir@01c21800 { + pinctrl-names = "default"; + pinctrl-0 = <&ir0_pins_a>; + status = "okay"; + }; + + uart0: serial@01c28000 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins_a>; + status = "okay"; + }; + + uart3: serial@01c28c00 { + pinctrl-names = "default"; + pinctrl-0 = <&uart3_pins_b>; + status = "okay"; + }; + + uart7: serial@01c29c00 { + pinctrl-names = "default"; + pinctrl-0 = <&uart7_pins_a>; + status = "okay"; + }; + + i2c0: i2c@01c2ac00 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins_a>; + status = "okay"; + + axp209: pmic@34 { + compatible = "x-powers,axp209"; + reg = <0x34>; + interrupt-parent = <&nmi_intc>; + interrupts = <0 8>; + + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + + i2c2: i2c@01c2b400 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins_a>; + status = "okay"; + }; + + gmac: ethernet@01c50000 { + pinctrl-names = "default"; + pinctrl-0 = <&gmac_pins_rgmii_a>; + phy = <&phy1>; + phy-mode = "rgmii"; + phy-supply = <®_gmac_3v3>; + status = "okay"; + + phy1: ethernet-phy@1 { + reg = <1>; + }; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&led_pins_bananapi>; + + green { + label = "bananapi:green:usr"; + gpios = <&pio 7 24 0>; + }; + }; + + reg_usb1_vbus: usb1-vbus { + status = "okay"; + }; + + reg_usb2_vbus: usb2-vbus { + status = "okay"; + }; + + reg_gmac_3v3: gmac-3v3 { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&gmac_power_pin_bananapi>; + regulator-name = "gmac-3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + startup-delay-us = <50000>; + enable-active-high; + gpio = <&pio 7 23 0>; + }; +}; -- 2.1.0 ^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH v2 0/3] ARM: dts: sun7i: Add Banana Pi board @ 2014-10-02 9:46 ` Maxime Ripard 0 siblings, 0 replies; 10+ messages in thread From: Maxime Ripard @ 2014-10-02 9:46 UTC (permalink / raw) To: linux-arm-kernel On Wed, Oct 01, 2014 at 09:26:03AM +0200, Hans de Goede wrote: > Hi Maxime, > > Here is v2 of the Bananapi board addition. Sorry for taking so long. > > Changes from v2: > -Move uart3_pins definition from a20-sun7i-bananapi.dts to a20-sun7i.dtsi, > the addition of the pinctrl node is done in a separate patch > -Use the new dual license header as license header Merged all three for 3.19. Thanks! Maxime -- Maxime Ripard, Free Electrons Embedded Linux, Kernel and Android engineering http://free-electrons.com -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 819 bytes Desc: Digital signature URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20141002/8fbdda27/attachment.sig> ^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH v2 0/3] ARM: dts: sun7i: Add Banana Pi board @ 2014-10-02 9:46 ` Maxime Ripard 0 siblings, 0 replies; 10+ messages in thread From: Maxime Ripard @ 2014-10-02 9:46 UTC (permalink / raw) To: Hans de Goede Cc: Ian Campbell, Karsten Merker, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, devicetree, linux-sunxi-/JYPxA39Uh5TLH3MbocFFw [-- Attachment #1: Type: text/plain, Size: 536 bytes --] On Wed, Oct 01, 2014 at 09:26:03AM +0200, Hans de Goede wrote: > Hi Maxime, > > Here is v2 of the Bananapi board addition. Sorry for taking so long. > > Changes from v2: > -Move uart3_pins definition from a20-sun7i-bananapi.dts to a20-sun7i.dtsi, > the addition of the pinctrl node is done in a separate patch > -Use the new dual license header as license header Merged all three for 3.19. Thanks! Maxime -- Maxime Ripard, Free Electrons Embedded Linux, Kernel and Android engineering http://free-electrons.com [-- Attachment #2: Digital signature --] [-- Type: application/pgp-signature, Size: 819 bytes --] ^ permalink raw reply [flat|nested] 10+ messages in thread
end of thread, other threads:[~2014-10-02 9:46 UTC | newest] Thread overview: 10+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2014-10-01 7:26 [PATCH v2 0/3] ARM: dts: sun7i: Add Banana Pi board Hans de Goede 2014-10-01 7:26 ` Hans de Goede 2014-10-01 7:26 ` [PATCH v2 1/3] ARM: dts: sun7i: Add spi0_pins_a pinctrl setting Hans de Goede 2014-10-01 7:26 ` Hans de Goede 2014-10-01 7:26 ` [PATCH v2 2/3] ARM: dts: sun7i: Add uart3_pins_b " Hans de Goede 2014-10-01 7:26 ` Hans de Goede 2014-10-01 7:26 ` [PATCH v2 3/3] ARM: dts: sun7i: Add Banana Pi board Hans de Goede 2014-10-01 7:26 ` Hans de Goede 2014-10-02 9:46 ` [PATCH v2 0/3] " Maxime Ripard 2014-10-02 9:46 ` Maxime Ripard
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.