From: Tony Lindgren <tony@atomide.com>
To: linux-omap@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Subject: [PATCH] ARM: OMAP4: Remove legacy PMIC platform code
Date: Wed, 14 Jan 2015 16:58:33 -0800 [thread overview]
Message-ID: <20150115005833.GA18552@atomide.com> (raw)
We've had omap4 booting in DT only mode for quite some time
now, let's remove the legacy PMIC code that's no longer
needed.
Signed-off-by: Tony Lindgren <tony@atomide.com>
--- a/arch/arm/mach-omap2/twl-common.c
+++ b/arch/arm/mach-omap2/twl-common.c
@@ -39,7 +39,7 @@ static struct i2c_board_info __initdata pmic_i2c_board_info = {
.flags = I2C_CLIENT_WAKE,
};
-#if defined(CONFIG_ARCH_OMAP3) || defined(CONFIG_ARCH_OMAP4)
+#if defined(CONFIG_ARCH_OMAP3)
static int twl_set_voltage(void *data, int target_uV)
{
struct voltagedomain *voltdm = (struct voltagedomain *)data;
@@ -66,20 +66,6 @@ void __init omap_pmic_init(int bus, u32 clkrate,
omap_register_i2c_bus(bus, clkrate, &pmic_i2c_board_info, 1);
}
-void __init omap4_pmic_init(const char *pmic_type,
- struct twl4030_platform_data *pmic_data,
- struct i2c_board_info *devices, int nr_devices)
-{
- /* PMIC part*/
- omap_mux_init_signal("sys_nirq1", OMAP_PIN_INPUT_PULLUP | OMAP_PIN_OFF_WAKEUPENABLE);
- omap_mux_init_signal("fref_clk0_out.sys_drm_msecure", OMAP_PIN_OUTPUT);
- omap_pmic_init(1, 400, pmic_type, 7 + OMAP44XX_IRQ_GIC_START, pmic_data);
-
- /* Register additional devices on i2c1 bus if needed */
- if (devices)
- i2c_register_board_info(1, devices, nr_devices);
-}
-
void __init omap_pmic_late_init(void)
{
/* Init the OMAP TWL parameters (if PMIC has been registerd) */
@@ -236,297 +222,6 @@ void __init omap3_pmic_get_config(struct twl4030_platform_data *pmic_data,
}
#endif /* CONFIG_ARCH_OMAP3 */
-#if defined(CONFIG_ARCH_OMAP4)
-static struct twl4030_usb_data omap4_usb_pdata = {
-};
-
-static struct regulator_consumer_supply omap4_vdda_hdmi_dac_supplies[] = {
- REGULATOR_SUPPLY("vdda_hdmi_dac", "omapdss_hdmi"),
-};
-
-static struct regulator_init_data omap4_vdac_idata = {
- .constraints = {
- .min_uV = 1800000,
- .max_uV = 1800000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(omap4_vdda_hdmi_dac_supplies),
- .consumer_supplies = omap4_vdda_hdmi_dac_supplies,
- .supply_regulator = "V2V1",
-};
-
-static struct regulator_init_data omap4_vaux2_idata = {
- .constraints = {
- .min_uV = 1200000,
- .max_uV = 2800000,
- .apply_uV = true,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
- | REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
-};
-
-static struct regulator_init_data omap4_vaux3_idata = {
- .constraints = {
- .min_uV = 1000000,
- .max_uV = 3000000,
- .apply_uV = true,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
- | REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
-};
-
-static struct regulator_consumer_supply omap4_vmmc_supply[] = {
- REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
-};
-
-/* VMMC1 for MMC1 card */
-static struct regulator_init_data omap4_vmmc_idata = {
- .constraints = {
- .min_uV = 1200000,
- .max_uV = 3000000,
- .apply_uV = true,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
- | REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(omap4_vmmc_supply),
- .consumer_supplies = omap4_vmmc_supply,
-};
-
-static struct regulator_init_data omap4_vpp_idata = {
- .constraints = {
- .min_uV = 1800000,
- .max_uV = 2500000,
- .apply_uV = true,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
- | REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
-};
-
-static struct regulator_init_data omap4_vana_idata = {
- .constraints = {
- .min_uV = 2100000,
- .max_uV = 2100000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
-};
-
-static struct regulator_consumer_supply omap4_vcxio_supply[] = {
- REGULATOR_SUPPLY("vdds_dsi", "omapdss_dss"),
- REGULATOR_SUPPLY("vdds_dsi", "omapdss_dsi.0"),
- REGULATOR_SUPPLY("vdds_dsi", "omapdss_dsi.1"),
-};
-
-static struct regulator_init_data omap4_vcxio_idata = {
- .constraints = {
- .min_uV = 1800000,
- .max_uV = 1800000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- .always_on = true,
- },
- .num_consumer_supplies = ARRAY_SIZE(omap4_vcxio_supply),
- .consumer_supplies = omap4_vcxio_supply,
- .supply_regulator = "V2V1",
-};
-
-static struct regulator_init_data omap4_vusb_idata = {
- .constraints = {
- .min_uV = 3300000,
- .max_uV = 3300000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
-};
-
-static struct regulator_init_data omap4_clk32kg_idata = {
- .constraints = {
- .valid_ops_mask = REGULATOR_CHANGE_STATUS,
- },
-};
-
-static struct regulator_consumer_supply omap4_vdd1_supply[] = {
- REGULATOR_SUPPLY("vcc", "cpu0"),
-};
-
-static struct regulator_consumer_supply omap4_vdd2_supply[] = {
- REGULATOR_SUPPLY("vcc", "iva.0"),
-};
-
-static struct regulator_consumer_supply omap4_vdd3_supply[] = {
- REGULATOR_SUPPLY("vcc", "l3_main.0"),
-};
-
-static struct regulator_init_data omap4_vdd1 = {
- .constraints = {
- .name = "vdd_mpu",
- .min_uV = 500000,
- .max_uV = 1500000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE,
- },
- .num_consumer_supplies = ARRAY_SIZE(omap4_vdd1_supply),
- .consumer_supplies = omap4_vdd1_supply,
-};
-
-static struct regulator_init_data omap4_vdd2 = {
- .constraints = {
- .name = "vdd_iva",
- .min_uV = 500000,
- .max_uV = 1500000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE,
- },
- .num_consumer_supplies = ARRAY_SIZE(omap4_vdd2_supply),
- .consumer_supplies = omap4_vdd2_supply,
-};
-
-static struct regulator_init_data omap4_vdd3 = {
- .constraints = {
- .name = "vdd_core",
- .min_uV = 500000,
- .max_uV = 1500000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE,
- },
- .num_consumer_supplies = ARRAY_SIZE(omap4_vdd3_supply),
- .consumer_supplies = omap4_vdd3_supply,
-};
-
-
-static struct twl_regulator_driver_data omap4_vdd1_drvdata = {
- .get_voltage = twl_get_voltage,
- .set_voltage = twl_set_voltage,
-};
-
-static struct twl_regulator_driver_data omap4_vdd2_drvdata = {
- .get_voltage = twl_get_voltage,
- .set_voltage = twl_set_voltage,
-};
-
-static struct twl_regulator_driver_data omap4_vdd3_drvdata = {
- .get_voltage = twl_get_voltage,
- .set_voltage = twl_set_voltage,
-};
-
-static struct regulator_consumer_supply omap4_v1v8_supply[] = {
- REGULATOR_SUPPLY("vio", "1-004b"),
-};
-
-static struct regulator_init_data omap4_v1v8_idata = {
- .constraints = {
- .min_uV = 1800000,
- .max_uV = 1800000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- .always_on = true,
- },
- .num_consumer_supplies = ARRAY_SIZE(omap4_v1v8_supply),
- .consumer_supplies = omap4_v1v8_supply,
-};
-
-static struct regulator_consumer_supply omap4_v2v1_supply[] = {
- REGULATOR_SUPPLY("v2v1", "1-004b"),
-};
-
-static struct regulator_init_data omap4_v2v1_idata = {
- .constraints = {
- .min_uV = 2100000,
- .max_uV = 2100000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(omap4_v2v1_supply),
- .consumer_supplies = omap4_v2v1_supply,
-};
-
-void __init omap4_pmic_get_config(struct twl4030_platform_data *pmic_data,
- u32 pdata_flags, u32 regulators_flags)
-{
- if (!pmic_data->vdd1) {
- omap4_vdd1.driver_data = &omap4_vdd1_drvdata;
- omap4_vdd1_drvdata.data = voltdm_lookup("mpu");
- pmic_data->vdd1 = &omap4_vdd1;
- }
-
- if (!pmic_data->vdd2) {
- omap4_vdd2.driver_data = &omap4_vdd2_drvdata;
- omap4_vdd2_drvdata.data = voltdm_lookup("iva");
- pmic_data->vdd2 = &omap4_vdd2;
- }
-
- if (!pmic_data->vdd3) {
- omap4_vdd3.driver_data = &omap4_vdd3_drvdata;
- omap4_vdd3_drvdata.data = voltdm_lookup("core");
- pmic_data->vdd3 = &omap4_vdd3;
- }
-
- /* Common platform data configurations */
- if (pdata_flags & TWL_COMMON_PDATA_USB && !pmic_data->usb)
- pmic_data->usb = &omap4_usb_pdata;
-
- /* Common regulator configurations */
- if (regulators_flags & TWL_COMMON_REGULATOR_VDAC && !pmic_data->vdac)
- pmic_data->vdac = &omap4_vdac_idata;
-
- if (regulators_flags & TWL_COMMON_REGULATOR_VAUX2 && !pmic_data->vaux2)
- pmic_data->vaux2 = &omap4_vaux2_idata;
-
- if (regulators_flags & TWL_COMMON_REGULATOR_VAUX3 && !pmic_data->vaux3)
- pmic_data->vaux3 = &omap4_vaux3_idata;
-
- if (regulators_flags & TWL_COMMON_REGULATOR_VMMC && !pmic_data->vmmc)
- pmic_data->vmmc = &omap4_vmmc_idata;
-
- if (regulators_flags & TWL_COMMON_REGULATOR_VPP && !pmic_data->vpp)
- pmic_data->vpp = &omap4_vpp_idata;
-
- if (regulators_flags & TWL_COMMON_REGULATOR_VANA && !pmic_data->vana)
- pmic_data->vana = &omap4_vana_idata;
-
- if (regulators_flags & TWL_COMMON_REGULATOR_VCXIO && !pmic_data->vcxio)
- pmic_data->vcxio = &omap4_vcxio_idata;
-
- if (regulators_flags & TWL_COMMON_REGULATOR_VUSB && !pmic_data->vusb)
- pmic_data->vusb = &omap4_vusb_idata;
-
- if (regulators_flags & TWL_COMMON_REGULATOR_CLK32KG &&
- !pmic_data->clk32kg)
- pmic_data->clk32kg = &omap4_clk32kg_idata;
-
- if (regulators_flags & TWL_COMMON_REGULATOR_V1V8 && !pmic_data->v1v8)
- pmic_data->v1v8 = &omap4_v1v8_idata;
-
- if (regulators_flags & TWL_COMMON_REGULATOR_V2V1 && !pmic_data->v2v1)
- pmic_data->v2v1 = &omap4_v2v1_idata;
-}
-#endif /* CONFIG_ARCH_OMAP4 */
-
#if defined(CONFIG_SND_OMAP_SOC_OMAP_TWL4030) || \
defined(CONFIG_SND_OMAP_SOC_OMAP_TWL4030_MODULE)
#include <linux/platform_data/omap-twl4030.h>
--- a/arch/arm/mach-omap2/twl-common.h
+++ b/arch/arm/mach-omap2/twl-common.h
@@ -31,7 +31,6 @@
struct twl4030_platform_data;
-struct twl6040_platform_data;
struct omap_tw4030_pdata;
struct i2c_board_info;
@@ -51,16 +50,9 @@ static inline void omap3_pmic_init(const char *pmic_type,
omap_pmic_init(1, 2600, pmic_type, 7 + OMAP_INTC_START, pmic_data);
}
-void omap4_pmic_init(const char *pmic_type,
- struct twl4030_platform_data *pmic_data,
- struct i2c_board_info *devices, int nr_devices);
-
void omap3_pmic_get_config(struct twl4030_platform_data *pmic_data,
u32 pdata_flags, u32 regulators_flags);
-void omap4_pmic_get_config(struct twl4030_platform_data *pmic_data,
- u32 pdata_flags, u32 regulators_flags);
-
void omap_twl4030_audio_init(char *card_name, struct omap_tw4030_pdata *pdata);
#endif /* __OMAP_PMIC_COMMON__ */
WARNING: multiple messages have this Message-ID (diff)
From: tony@atomide.com (Tony Lindgren)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH] ARM: OMAP4: Remove legacy PMIC platform code
Date: Wed, 14 Jan 2015 16:58:33 -0800 [thread overview]
Message-ID: <20150115005833.GA18552@atomide.com> (raw)
We've had omap4 booting in DT only mode for quite some time
now, let's remove the legacy PMIC code that's no longer
needed.
Signed-off-by: Tony Lindgren <tony@atomide.com>
--- a/arch/arm/mach-omap2/twl-common.c
+++ b/arch/arm/mach-omap2/twl-common.c
@@ -39,7 +39,7 @@ static struct i2c_board_info __initdata pmic_i2c_board_info = {
.flags = I2C_CLIENT_WAKE,
};
-#if defined(CONFIG_ARCH_OMAP3) || defined(CONFIG_ARCH_OMAP4)
+#if defined(CONFIG_ARCH_OMAP3)
static int twl_set_voltage(void *data, int target_uV)
{
struct voltagedomain *voltdm = (struct voltagedomain *)data;
@@ -66,20 +66,6 @@ void __init omap_pmic_init(int bus, u32 clkrate,
omap_register_i2c_bus(bus, clkrate, &pmic_i2c_board_info, 1);
}
-void __init omap4_pmic_init(const char *pmic_type,
- struct twl4030_platform_data *pmic_data,
- struct i2c_board_info *devices, int nr_devices)
-{
- /* PMIC part*/
- omap_mux_init_signal("sys_nirq1", OMAP_PIN_INPUT_PULLUP | OMAP_PIN_OFF_WAKEUPENABLE);
- omap_mux_init_signal("fref_clk0_out.sys_drm_msecure", OMAP_PIN_OUTPUT);
- omap_pmic_init(1, 400, pmic_type, 7 + OMAP44XX_IRQ_GIC_START, pmic_data);
-
- /* Register additional devices on i2c1 bus if needed */
- if (devices)
- i2c_register_board_info(1, devices, nr_devices);
-}
-
void __init omap_pmic_late_init(void)
{
/* Init the OMAP TWL parameters (if PMIC has been registerd) */
@@ -236,297 +222,6 @@ void __init omap3_pmic_get_config(struct twl4030_platform_data *pmic_data,
}
#endif /* CONFIG_ARCH_OMAP3 */
-#if defined(CONFIG_ARCH_OMAP4)
-static struct twl4030_usb_data omap4_usb_pdata = {
-};
-
-static struct regulator_consumer_supply omap4_vdda_hdmi_dac_supplies[] = {
- REGULATOR_SUPPLY("vdda_hdmi_dac", "omapdss_hdmi"),
-};
-
-static struct regulator_init_data omap4_vdac_idata = {
- .constraints = {
- .min_uV = 1800000,
- .max_uV = 1800000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(omap4_vdda_hdmi_dac_supplies),
- .consumer_supplies = omap4_vdda_hdmi_dac_supplies,
- .supply_regulator = "V2V1",
-};
-
-static struct regulator_init_data omap4_vaux2_idata = {
- .constraints = {
- .min_uV = 1200000,
- .max_uV = 2800000,
- .apply_uV = true,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
- | REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
-};
-
-static struct regulator_init_data omap4_vaux3_idata = {
- .constraints = {
- .min_uV = 1000000,
- .max_uV = 3000000,
- .apply_uV = true,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
- | REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
-};
-
-static struct regulator_consumer_supply omap4_vmmc_supply[] = {
- REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
-};
-
-/* VMMC1 for MMC1 card */
-static struct regulator_init_data omap4_vmmc_idata = {
- .constraints = {
- .min_uV = 1200000,
- .max_uV = 3000000,
- .apply_uV = true,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
- | REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(omap4_vmmc_supply),
- .consumer_supplies = omap4_vmmc_supply,
-};
-
-static struct regulator_init_data omap4_vpp_idata = {
- .constraints = {
- .min_uV = 1800000,
- .max_uV = 2500000,
- .apply_uV = true,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
- | REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
-};
-
-static struct regulator_init_data omap4_vana_idata = {
- .constraints = {
- .min_uV = 2100000,
- .max_uV = 2100000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
-};
-
-static struct regulator_consumer_supply omap4_vcxio_supply[] = {
- REGULATOR_SUPPLY("vdds_dsi", "omapdss_dss"),
- REGULATOR_SUPPLY("vdds_dsi", "omapdss_dsi.0"),
- REGULATOR_SUPPLY("vdds_dsi", "omapdss_dsi.1"),
-};
-
-static struct regulator_init_data omap4_vcxio_idata = {
- .constraints = {
- .min_uV = 1800000,
- .max_uV = 1800000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- .always_on = true,
- },
- .num_consumer_supplies = ARRAY_SIZE(omap4_vcxio_supply),
- .consumer_supplies = omap4_vcxio_supply,
- .supply_regulator = "V2V1",
-};
-
-static struct regulator_init_data omap4_vusb_idata = {
- .constraints = {
- .min_uV = 3300000,
- .max_uV = 3300000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
-};
-
-static struct regulator_init_data omap4_clk32kg_idata = {
- .constraints = {
- .valid_ops_mask = REGULATOR_CHANGE_STATUS,
- },
-};
-
-static struct regulator_consumer_supply omap4_vdd1_supply[] = {
- REGULATOR_SUPPLY("vcc", "cpu0"),
-};
-
-static struct regulator_consumer_supply omap4_vdd2_supply[] = {
- REGULATOR_SUPPLY("vcc", "iva.0"),
-};
-
-static struct regulator_consumer_supply omap4_vdd3_supply[] = {
- REGULATOR_SUPPLY("vcc", "l3_main.0"),
-};
-
-static struct regulator_init_data omap4_vdd1 = {
- .constraints = {
- .name = "vdd_mpu",
- .min_uV = 500000,
- .max_uV = 1500000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE,
- },
- .num_consumer_supplies = ARRAY_SIZE(omap4_vdd1_supply),
- .consumer_supplies = omap4_vdd1_supply,
-};
-
-static struct regulator_init_data omap4_vdd2 = {
- .constraints = {
- .name = "vdd_iva",
- .min_uV = 500000,
- .max_uV = 1500000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE,
- },
- .num_consumer_supplies = ARRAY_SIZE(omap4_vdd2_supply),
- .consumer_supplies = omap4_vdd2_supply,
-};
-
-static struct regulator_init_data omap4_vdd3 = {
- .constraints = {
- .name = "vdd_core",
- .min_uV = 500000,
- .max_uV = 1500000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE,
- },
- .num_consumer_supplies = ARRAY_SIZE(omap4_vdd3_supply),
- .consumer_supplies = omap4_vdd3_supply,
-};
-
-
-static struct twl_regulator_driver_data omap4_vdd1_drvdata = {
- .get_voltage = twl_get_voltage,
- .set_voltage = twl_set_voltage,
-};
-
-static struct twl_regulator_driver_data omap4_vdd2_drvdata = {
- .get_voltage = twl_get_voltage,
- .set_voltage = twl_set_voltage,
-};
-
-static struct twl_regulator_driver_data omap4_vdd3_drvdata = {
- .get_voltage = twl_get_voltage,
- .set_voltage = twl_set_voltage,
-};
-
-static struct regulator_consumer_supply omap4_v1v8_supply[] = {
- REGULATOR_SUPPLY("vio", "1-004b"),
-};
-
-static struct regulator_init_data omap4_v1v8_idata = {
- .constraints = {
- .min_uV = 1800000,
- .max_uV = 1800000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- .always_on = true,
- },
- .num_consumer_supplies = ARRAY_SIZE(omap4_v1v8_supply),
- .consumer_supplies = omap4_v1v8_supply,
-};
-
-static struct regulator_consumer_supply omap4_v2v1_supply[] = {
- REGULATOR_SUPPLY("v2v1", "1-004b"),
-};
-
-static struct regulator_init_data omap4_v2v1_idata = {
- .constraints = {
- .min_uV = 2100000,
- .max_uV = 2100000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(omap4_v2v1_supply),
- .consumer_supplies = omap4_v2v1_supply,
-};
-
-void __init omap4_pmic_get_config(struct twl4030_platform_data *pmic_data,
- u32 pdata_flags, u32 regulators_flags)
-{
- if (!pmic_data->vdd1) {
- omap4_vdd1.driver_data = &omap4_vdd1_drvdata;
- omap4_vdd1_drvdata.data = voltdm_lookup("mpu");
- pmic_data->vdd1 = &omap4_vdd1;
- }
-
- if (!pmic_data->vdd2) {
- omap4_vdd2.driver_data = &omap4_vdd2_drvdata;
- omap4_vdd2_drvdata.data = voltdm_lookup("iva");
- pmic_data->vdd2 = &omap4_vdd2;
- }
-
- if (!pmic_data->vdd3) {
- omap4_vdd3.driver_data = &omap4_vdd3_drvdata;
- omap4_vdd3_drvdata.data = voltdm_lookup("core");
- pmic_data->vdd3 = &omap4_vdd3;
- }
-
- /* Common platform data configurations */
- if (pdata_flags & TWL_COMMON_PDATA_USB && !pmic_data->usb)
- pmic_data->usb = &omap4_usb_pdata;
-
- /* Common regulator configurations */
- if (regulators_flags & TWL_COMMON_REGULATOR_VDAC && !pmic_data->vdac)
- pmic_data->vdac = &omap4_vdac_idata;
-
- if (regulators_flags & TWL_COMMON_REGULATOR_VAUX2 && !pmic_data->vaux2)
- pmic_data->vaux2 = &omap4_vaux2_idata;
-
- if (regulators_flags & TWL_COMMON_REGULATOR_VAUX3 && !pmic_data->vaux3)
- pmic_data->vaux3 = &omap4_vaux3_idata;
-
- if (regulators_flags & TWL_COMMON_REGULATOR_VMMC && !pmic_data->vmmc)
- pmic_data->vmmc = &omap4_vmmc_idata;
-
- if (regulators_flags & TWL_COMMON_REGULATOR_VPP && !pmic_data->vpp)
- pmic_data->vpp = &omap4_vpp_idata;
-
- if (regulators_flags & TWL_COMMON_REGULATOR_VANA && !pmic_data->vana)
- pmic_data->vana = &omap4_vana_idata;
-
- if (regulators_flags & TWL_COMMON_REGULATOR_VCXIO && !pmic_data->vcxio)
- pmic_data->vcxio = &omap4_vcxio_idata;
-
- if (regulators_flags & TWL_COMMON_REGULATOR_VUSB && !pmic_data->vusb)
- pmic_data->vusb = &omap4_vusb_idata;
-
- if (regulators_flags & TWL_COMMON_REGULATOR_CLK32KG &&
- !pmic_data->clk32kg)
- pmic_data->clk32kg = &omap4_clk32kg_idata;
-
- if (regulators_flags & TWL_COMMON_REGULATOR_V1V8 && !pmic_data->v1v8)
- pmic_data->v1v8 = &omap4_v1v8_idata;
-
- if (regulators_flags & TWL_COMMON_REGULATOR_V2V1 && !pmic_data->v2v1)
- pmic_data->v2v1 = &omap4_v2v1_idata;
-}
-#endif /* CONFIG_ARCH_OMAP4 */
-
#if defined(CONFIG_SND_OMAP_SOC_OMAP_TWL4030) || \
defined(CONFIG_SND_OMAP_SOC_OMAP_TWL4030_MODULE)
#include <linux/platform_data/omap-twl4030.h>
--- a/arch/arm/mach-omap2/twl-common.h
+++ b/arch/arm/mach-omap2/twl-common.h
@@ -31,7 +31,6 @@
struct twl4030_platform_data;
-struct twl6040_platform_data;
struct omap_tw4030_pdata;
struct i2c_board_info;
@@ -51,16 +50,9 @@ static inline void omap3_pmic_init(const char *pmic_type,
omap_pmic_init(1, 2600, pmic_type, 7 + OMAP_INTC_START, pmic_data);
}
-void omap4_pmic_init(const char *pmic_type,
- struct twl4030_platform_data *pmic_data,
- struct i2c_board_info *devices, int nr_devices);
-
void omap3_pmic_get_config(struct twl4030_platform_data *pmic_data,
u32 pdata_flags, u32 regulators_flags);
-void omap4_pmic_get_config(struct twl4030_platform_data *pmic_data,
- u32 pdata_flags, u32 regulators_flags);
-
void omap_twl4030_audio_init(char *card_name, struct omap_tw4030_pdata *pdata);
#endif /* __OMAP_PMIC_COMMON__ */
next reply other threads:[~2015-01-15 1:02 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-01-15 0:58 Tony Lindgren [this message]
2015-01-15 0:58 ` [PATCH] ARM: OMAP4: Remove legacy PMIC platform code Tony Lindgren
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20150115005833.GA18552@atomide.com \
--to=tony@atomide.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-omap@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.