* [PATCH 1/9] phy: ti-pipe3: Disable clocks on system suspend
2015-01-31 14:28 [GIT PULL 0/9] phy: for 3.20 merge window Kishon Vijay Abraham I
@ 2015-01-31 14:28 ` Kishon Vijay Abraham I
2015-01-31 14:28 ` [PATCH 2/9] phy: ti-pipe3: Fix SATA across suspend/resume Kishon Vijay Abraham I
` (8 subsequent siblings)
9 siblings, 0 replies; 11+ messages in thread
From: Kishon Vijay Abraham I @ 2015-01-31 14:28 UTC (permalink / raw)
To: gregkh; +Cc: kishon, linux-kernel
From: Roger Quadros <rogerq@ti.com>
On system suspend, the runtime_suspend() driver hook doesn't get
called for USB phy and so the clocks are not disabled in the driver.
This causes the L3INIT_960M_GFCLK and L3INIT_480M_GFCLK to remain
active on the DRA7 platform while in system suspend.
In case of pcie-phy, the runtime_suspend hook gets called after
the suspend hook so we introduce a flag phy->enabled to keep
track if our clocks are enabled or not to prevent multiple
enable/disables.
Add suspend/resume hooks to the driver.
Move enabling/disabling clock code into helper functions.
Reported-by: Nishant Menon <nm@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
---
drivers/phy/phy-ti-pipe3.c | 99 ++++++++++++++++++++++++++++++++++----------
1 file changed, 77 insertions(+), 22 deletions(-)
diff --git a/drivers/phy/phy-ti-pipe3.c b/drivers/phy/phy-ti-pipe3.c
index 465de2c..8c85468 100644
--- a/drivers/phy/phy-ti-pipe3.c
+++ b/drivers/phy/phy-ti-pipe3.c
@@ -28,6 +28,7 @@
#include <linux/delay.h>
#include <linux/phy/omap_control_phy.h>
#include <linux/of_platform.h>
+#include <linux/spinlock.h>
#define PLL_STATUS 0x00000004
#define PLL_GO 0x00000008
@@ -82,6 +83,8 @@ struct ti_pipe3 {
struct clk *refclk;
struct clk *div_clk;
struct pipe3_dpll_map *dpll_map;
+ bool enabled;
+ spinlock_t lock; /* serialize clock enable/disable */
};
static struct pipe3_dpll_map dpll_map_usb[] = {
@@ -307,6 +310,7 @@ static int ti_pipe3_probe(struct platform_device *pdev)
return -ENOMEM;
phy->dev = &pdev->dev;
+ spin_lock_init(&phy->lock);
if (!of_device_is_compatible(node, "ti,phy-pipe3-pcie")) {
match = of_match_device(of_match_ptr(ti_pipe3_id_table),
@@ -427,24 +431,14 @@ static int ti_pipe3_remove(struct platform_device *pdev)
#ifdef CONFIG_PM
-static int ti_pipe3_runtime_suspend(struct device *dev)
+static int ti_pipe3_enable_clocks(struct ti_pipe3 *phy)
{
- struct ti_pipe3 *phy = dev_get_drvdata(dev);
-
- if (!IS_ERR(phy->wkupclk))
- clk_disable_unprepare(phy->wkupclk);
- if (!IS_ERR(phy->refclk))
- clk_disable_unprepare(phy->refclk);
- if (!IS_ERR(phy->div_clk))
- clk_disable_unprepare(phy->div_clk);
-
- return 0;
-}
+ int ret = 0;
+ unsigned long flags;
-static int ti_pipe3_runtime_resume(struct device *dev)
-{
- u32 ret = 0;
- struct ti_pipe3 *phy = dev_get_drvdata(dev);
+ spin_lock_irqsave(&phy->lock, flags);
+ if (phy->enabled)
+ goto err1;
if (!IS_ERR(phy->refclk)) {
ret = clk_prepare_enable(phy->refclk);
@@ -469,6 +463,9 @@ static int ti_pipe3_runtime_resume(struct device *dev)
goto err3;
}
}
+
+ phy->enabled = true;
+ spin_unlock_irqrestore(&phy->lock, flags);
return 0;
err3:
@@ -480,19 +477,77 @@ err2:
clk_disable_unprepare(phy->refclk);
err1:
+ spin_unlock_irqrestore(&phy->lock, flags);
+ return ret;
+}
+
+static void ti_pipe3_disable_clocks(struct ti_pipe3 *phy)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&phy->lock, flags);
+ if (!phy->enabled) {
+ spin_unlock_irqrestore(&phy->lock, flags);
+ return;
+ }
+
+ if (!IS_ERR(phy->wkupclk))
+ clk_disable_unprepare(phy->wkupclk);
+ if (!IS_ERR(phy->refclk))
+ clk_disable_unprepare(phy->refclk);
+ if (!IS_ERR(phy->div_clk))
+ clk_disable_unprepare(phy->div_clk);
+ phy->enabled = false;
+ spin_unlock_irqrestore(&phy->lock, flags);
+}
+
+static int ti_pipe3_runtime_suspend(struct device *dev)
+{
+ struct ti_pipe3 *phy = dev_get_drvdata(dev);
+
+ ti_pipe3_disable_clocks(phy);
+ return 0;
+}
+
+static int ti_pipe3_runtime_resume(struct device *dev)
+{
+ struct ti_pipe3 *phy = dev_get_drvdata(dev);
+ int ret = 0;
+
+ ret = ti_pipe3_enable_clocks(phy);
return ret;
}
+static int ti_pipe3_suspend(struct device *dev)
+{
+ struct ti_pipe3 *phy = dev_get_drvdata(dev);
+
+ ti_pipe3_disable_clocks(phy);
+ return 0;
+}
+
+static int ti_pipe3_resume(struct device *dev)
+{
+ struct ti_pipe3 *phy = dev_get_drvdata(dev);
+ int ret;
+
+ ret = ti_pipe3_enable_clocks(phy);
+ if (ret)
+ return ret;
+
+ pm_runtime_disable(dev);
+ pm_runtime_set_active(dev);
+ pm_runtime_enable(dev);
+ return 0;
+}
+#endif
+
static const struct dev_pm_ops ti_pipe3_pm_ops = {
SET_RUNTIME_PM_OPS(ti_pipe3_runtime_suspend,
ti_pipe3_runtime_resume, NULL)
+ SET_SYSTEM_SLEEP_PM_OPS(ti_pipe3_suspend, ti_pipe3_resume)
};
-#define DEV_PM_OPS (&ti_pipe3_pm_ops)
-#else
-#define DEV_PM_OPS NULL
-#endif
-
#ifdef CONFIG_OF
static const struct of_device_id ti_pipe3_id_table[] = {
{
@@ -520,7 +575,7 @@ static struct platform_driver ti_pipe3_driver = {
.remove = ti_pipe3_remove,
.driver = {
.name = "ti-pipe3",
- .pm = DEV_PM_OPS,
+ .pm = &ti_pipe3_pm_ops,
.of_match_table = of_match_ptr(ti_pipe3_id_table),
},
};
--
1.7.9.5
^ permalink raw reply related [flat|nested] 11+ messages in thread* [PATCH 2/9] phy: ti-pipe3: Fix SATA across suspend/resume
2015-01-31 14:28 [GIT PULL 0/9] phy: for 3.20 merge window Kishon Vijay Abraham I
2015-01-31 14:28 ` [PATCH 1/9] phy: ti-pipe3: Disable clocks on system suspend Kishon Vijay Abraham I
@ 2015-01-31 14:28 ` Kishon Vijay Abraham I
2015-01-31 14:28 ` [PATCH 3/9] phy: fix return value check in armada375_usb_phy_probe() Kishon Vijay Abraham I
` (7 subsequent siblings)
9 siblings, 0 replies; 11+ messages in thread
From: Kishon Vijay Abraham I @ 2015-01-31 14:28 UTC (permalink / raw)
To: gregkh; +Cc: kishon, linux-kernel
From: Roger Quadros <rogerq@ti.com>
Failed test case: Boot without SATA drive connected. Suspend/resume
the board and then connect SATA drive. It fails to enumerate.
Due to Errata i783 "SATA Lockup After SATA DPLL Unlock/Relock"
we can't allow SATA DPLL to be in the unlocked state.
The SATA refclk (sata_ref_clk) is the source of the SATA_DPLL.
This clock is being controlled only by the AHCI SATA driver and is
shut off during system suspend (if the SATA drive was not already attached)
causing the SATA DPLL to be unlocked and so causing errata i783.
To prevent sata_ref_clk from being disabled, we add the control of
this clock to the SATA PHY driver and prevent it from being disabled.
This also fixes the issue of SATA not working on OMAP5/DRA7 when
AHCI platform driver is built as a module.
NOTE: Device tree changes also required for OMAP5 & DRA7.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
---
drivers/phy/phy-ti-pipe3.c | 58 ++++++++++++++++++++++++++++++++------------
1 file changed, 42 insertions(+), 16 deletions(-)
diff --git a/drivers/phy/phy-ti-pipe3.c b/drivers/phy/phy-ti-pipe3.c
index 8c85468..95c88f9 100644
--- a/drivers/phy/phy-ti-pipe3.c
+++ b/drivers/phy/phy-ti-pipe3.c
@@ -85,6 +85,8 @@ struct ti_pipe3 {
struct pipe3_dpll_map *dpll_map;
bool enabled;
spinlock_t lock; /* serialize clock enable/disable */
+ /* the below flag is needed specifically for SATA */
+ bool refclk_enabled;
};
static struct pipe3_dpll_map dpll_map_usb[] = {
@@ -337,21 +339,24 @@ static int ti_pipe3_probe(struct platform_device *pdev)
}
}
+ phy->refclk = devm_clk_get(phy->dev, "refclk");
+ if (IS_ERR(phy->refclk)) {
+ dev_err(&pdev->dev, "unable to get refclk\n");
+ /* older DTBs have missing refclk in SATA PHY
+ * so don't bail out in case of SATA PHY.
+ */
+ if (!of_device_is_compatible(node, "ti,phy-pipe3-sata"))
+ return PTR_ERR(phy->refclk);
+ }
+
if (!of_device_is_compatible(node, "ti,phy-pipe3-sata")) {
phy->wkupclk = devm_clk_get(phy->dev, "wkupclk");
if (IS_ERR(phy->wkupclk)) {
dev_err(&pdev->dev, "unable to get wkupclk\n");
return PTR_ERR(phy->wkupclk);
}
-
- phy->refclk = devm_clk_get(phy->dev, "refclk");
- if (IS_ERR(phy->refclk)) {
- dev_err(&pdev->dev, "unable to get refclk\n");
- return PTR_ERR(phy->refclk);
- }
} else {
phy->wkupclk = ERR_PTR(-ENODEV);
- phy->refclk = ERR_PTR(-ENODEV);
}
if (of_device_is_compatible(node, "ti,phy-pipe3-pcie")) {
@@ -430,6 +435,29 @@ static int ti_pipe3_remove(struct platform_device *pdev)
}
#ifdef CONFIG_PM
+static int ti_pipe3_enable_refclk(struct ti_pipe3 *phy)
+{
+ if (!IS_ERR(phy->refclk) && !phy->refclk_enabled) {
+ int ret;
+
+ ret = clk_prepare_enable(phy->refclk);
+ if (ret) {
+ dev_err(phy->dev, "Failed to enable refclk %d\n", ret);
+ return ret;
+ }
+ phy->refclk_enabled = true;
+ }
+
+ return 0;
+}
+
+static void ti_pipe3_disable_refclk(struct ti_pipe3 *phy)
+{
+ if (!IS_ERR(phy->refclk))
+ clk_disable_unprepare(phy->refclk);
+
+ phy->refclk_enabled = false;
+}
static int ti_pipe3_enable_clocks(struct ti_pipe3 *phy)
{
@@ -440,13 +468,9 @@ static int ti_pipe3_enable_clocks(struct ti_pipe3 *phy)
if (phy->enabled)
goto err1;
- if (!IS_ERR(phy->refclk)) {
- ret = clk_prepare_enable(phy->refclk);
- if (ret) {
- dev_err(phy->dev, "Failed to enable refclk %d\n", ret);
- goto err1;
- }
- }
+ ret = ti_pipe3_enable_refclk(phy);
+ if (ret)
+ goto err1;
if (!IS_ERR(phy->wkupclk)) {
ret = clk_prepare_enable(phy->wkupclk);
@@ -476,6 +500,7 @@ err2:
if (!IS_ERR(phy->refclk))
clk_disable_unprepare(phy->refclk);
+ ti_pipe3_disable_refclk(phy);
err1:
spin_unlock_irqrestore(&phy->lock, flags);
return ret;
@@ -493,8 +518,9 @@ static void ti_pipe3_disable_clocks(struct ti_pipe3 *phy)
if (!IS_ERR(phy->wkupclk))
clk_disable_unprepare(phy->wkupclk);
- if (!IS_ERR(phy->refclk))
- clk_disable_unprepare(phy->refclk);
+ /* Don't disable refclk for SATA PHY due to Errata i783 */
+ if (!of_device_is_compatible(phy->dev->of_node, "ti,phy-pipe3-sata"))
+ ti_pipe3_disable_refclk(phy);
if (!IS_ERR(phy->div_clk))
clk_disable_unprepare(phy->div_clk);
phy->enabled = false;
--
1.7.9.5
^ permalink raw reply related [flat|nested] 11+ messages in thread* [PATCH 3/9] phy: fix return value check in armada375_usb_phy_probe()
2015-01-31 14:28 [GIT PULL 0/9] phy: for 3.20 merge window Kishon Vijay Abraham I
2015-01-31 14:28 ` [PATCH 1/9] phy: ti-pipe3: Disable clocks on system suspend Kishon Vijay Abraham I
2015-01-31 14:28 ` [PATCH 2/9] phy: ti-pipe3: Fix SATA across suspend/resume Kishon Vijay Abraham I
@ 2015-01-31 14:28 ` Kishon Vijay Abraham I
2015-01-31 14:28 ` [PATCH 4/9] phy: miphy28lp: Pass sysconfig register offsets via syscfg dt property Kishon Vijay Abraham I
` (6 subsequent siblings)
9 siblings, 0 replies; 11+ messages in thread
From: Kishon Vijay Abraham I @ 2015-01-31 14:28 UTC (permalink / raw)
To: gregkh; +Cc: kishon, linux-kernel
From: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
In case of error, the function devm_ioremap_resource() returns
ERR_PTR() and never returns NULL. The NULL test in the return
value check should be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
---
drivers/phy/phy-armada375-usb2.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/drivers/phy/phy-armada375-usb2.c b/drivers/phy/phy-armada375-usb2.c
index ac7d99d..7c99ca2 100644
--- a/drivers/phy/phy-armada375-usb2.c
+++ b/drivers/phy/phy-armada375-usb2.c
@@ -118,8 +118,8 @@ static int armada375_usb_phy_probe(struct platform_device *pdev)
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
usb_cluster_base = devm_ioremap_resource(&pdev->dev, res);
- if (!usb_cluster_base)
- return -ENOMEM;
+ if (IS_ERR(usb_cluster_base))
+ return PTR_ERR(usb_cluster_base);
phy = devm_phy_create(dev, NULL, &armada375_usb_phy_ops);
if (IS_ERR(phy)) {
--
1.7.9.5
^ permalink raw reply related [flat|nested] 11+ messages in thread* [PATCH 4/9] phy: miphy28lp: Pass sysconfig register offsets via syscfg dt property.
2015-01-31 14:28 [GIT PULL 0/9] phy: for 3.20 merge window Kishon Vijay Abraham I
` (2 preceding siblings ...)
2015-01-31 14:28 ` [PATCH 3/9] phy: fix return value check in armada375_usb_phy_probe() Kishon Vijay Abraham I
@ 2015-01-31 14:28 ` Kishon Vijay Abraham I
2015-01-31 14:28 ` [PATCH 5/9] phy: phy-stih407-usb: Pass sysconfig register offsets via syscfg property Kishon Vijay Abraham I
` (5 subsequent siblings)
9 siblings, 0 replies; 11+ messages in thread
From: Kishon Vijay Abraham I @ 2015-01-31 14:28 UTC (permalink / raw)
To: gregkh; +Cc: kishon, linux-kernel
From: Gabriel FERNANDEZ <gabriel.fernandez@st.com>
Based on Arnds review comments here https://lkml.org/lkml/2014/11/13/161,
update the miphy28lp phy driver to access sysconfig register offsets via
syscfg dt property.
This is because the reg property should not be mixing address spaces like
it does currently for miphy28lp. This change then also aligns us to how other
platforms such as keystone and bcm7445 pass there syscon offsets via DT.
I have updated the miphy28lp phy driver same way as Peter's implementation.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
---
.../devicetree/bindings/phy/phy-miphy28lp.txt | 43 +++++---------
drivers/phy/phy-miphy28lp.c | 61 ++++++++++----------
2 files changed, 48 insertions(+), 56 deletions(-)
diff --git a/Documentation/devicetree/bindings/phy/phy-miphy28lp.txt b/Documentation/devicetree/bindings/phy/phy-miphy28lp.txt
index 46a135d..89caa88 100644
--- a/Documentation/devicetree/bindings/phy/phy-miphy28lp.txt
+++ b/Documentation/devicetree/bindings/phy/phy-miphy28lp.txt
@@ -26,6 +26,7 @@ Required properties (port (child) node):
filled in "reg". It can also contain the offset of the system configuration
registers used as glue-logic to setup the device for SATA/PCIe or USB3
devices.
+- st,syscfg : Offset of the parent configuration register.
- resets : phandle to the parent reset controller.
- reset-names : Associated name must be "miphy-sw-rst".
@@ -54,18 +55,12 @@ example:
phy_port0: port@9b22000 {
reg = <0x9b22000 0xff>,
<0x9b09000 0xff>,
- <0x9b04000 0xff>,
- <0x114 0x4>, /* sysctrl MiPHY cntrl */
- <0x818 0x4>, /* sysctrl MiPHY status*/
- <0xe0 0x4>, /* sysctrl PCIe */
- <0xec 0x4>; /* sysctrl SATA */
+ <0x9b04000 0xff>;
reg-names = "sata-up",
"pcie-up",
- "pipew",
- "miphy-ctrl-glue",
- "miphy-status-glue",
- "pcie-glue",
- "sata-glue";
+ "pipew";
+
+ st,syscfg = <0x114 0x818 0xe0 0xec>;
#phy-cells = <1>;
st,osc-rdy;
reset-names = "miphy-sw-rst";
@@ -75,18 +70,13 @@ example:
phy_port1: port@9b2a000 {
reg = <0x9b2a000 0xff>,
<0x9b19000 0xff>,
- <0x9b14000 0xff>,
- <0x118 0x4>,
- <0x81c 0x4>,
- <0xe4 0x4>,
- <0xf0 0x4>;
+ <0x9b14000 0xff>;
reg-names = "sata-up",
"pcie-up",
- "pipew",
- "miphy-ctrl-glue",
- "miphy-status-glue",
- "pcie-glue",
- "sata-glue";
+ "pipew";
+
+ st,syscfg = <0x118 0x81c 0xe4 0xf0>;
+
#phy-cells = <1>;
st,osc-force-ext;
reset-names = "miphy-sw-rst";
@@ -95,13 +85,12 @@ example:
phy_port2: port@8f95000 {
reg = <0x8f95000 0xff>,
- <0x8f90000 0xff>,
- <0x11c 0x4>,
- <0x820 0x4>;
+ <0x8f90000 0xff>;
reg-names = "pipew",
- "usb3-up",
- "miphy-ctrl-glue",
- "miphy-status-glue";
+ "usb3-up";
+
+ st,syscfg = <0x11c 0x820>;
+
#phy-cells = <1>;
reset-names = "miphy-sw-rst";
resets = <&softreset STIH407_MIPHY2_SOFTRESET>;
@@ -125,4 +114,4 @@ example:
Macro definitions for the supported miphy configuration can be found in:
-include/dt-bindings/phy/phy-miphy28lp.h
+include/dt-bindings/phy/phy.h
diff --git a/drivers/phy/phy-miphy28lp.c b/drivers/phy/phy-miphy28lp.c
index 27fa62c..9b2848e 100644
--- a/drivers/phy/phy-miphy28lp.c
+++ b/drivers/phy/phy-miphy28lp.c
@@ -194,6 +194,14 @@
#define MIPHY_SATA_BANK_NB 3
#define MIPHY_PCIE_BANK_NB 2
+enum {
+ SYSCFG_CTRL,
+ SYSCFG_STATUS,
+ SYSCFG_PCI,
+ SYSCFG_SATA,
+ SYSCFG_REG_MAX,
+};
+
struct miphy28lp_phy {
struct phy *phy;
struct miphy28lp_dev *phydev;
@@ -211,10 +219,7 @@ struct miphy28lp_phy {
u32 sata_gen;
/* Sysconfig registers offsets needed to configure the device */
- u32 syscfg_miphy_ctrl;
- u32 syscfg_miphy_status;
- u32 syscfg_pci;
- u32 syscfg_sata;
+ u32 syscfg_reg[SYSCFG_REG_MAX];
u8 type;
};
@@ -834,12 +839,12 @@ static int miphy_osc_is_ready(struct miphy28lp_phy *miphy_phy)
if (!miphy_phy->osc_rdy)
return 0;
- if (!miphy_phy->syscfg_miphy_status)
+ if (!miphy_phy->syscfg_reg[SYSCFG_STATUS])
return -EINVAL;
do {
- regmap_read(miphy_dev->regmap, miphy_phy->syscfg_miphy_status,
- &val);
+ regmap_read(miphy_dev->regmap,
+ miphy_phy->syscfg_reg[SYSCFG_STATUS], &val);
if ((val & MIPHY_OSC_RDY) != MIPHY_OSC_RDY)
cpu_relax();
@@ -888,7 +893,7 @@ static int miphy28lp_setup(struct miphy28lp_phy *miphy_phy, u32 miphy_val)
int err;
struct miphy28lp_dev *miphy_dev = miphy_phy->phydev;
- if (!miphy_phy->syscfg_miphy_ctrl)
+ if (!miphy_phy->syscfg_reg[SYSCFG_CTRL])
return -EINVAL;
err = reset_control_assert(miphy_phy->miphy_rst);
@@ -900,7 +905,8 @@ static int miphy28lp_setup(struct miphy28lp_phy *miphy_phy, u32 miphy_val)
if (miphy_phy->osc_force_ext)
miphy_val |= MIPHY_OSC_FORCE_EXT;
- regmap_update_bits(miphy_dev->regmap, miphy_phy->syscfg_miphy_ctrl,
+ regmap_update_bits(miphy_dev->regmap,
+ miphy_phy->syscfg_reg[SYSCFG_CTRL],
MIPHY_CTRL_MASK, miphy_val);
err = reset_control_deassert(miphy_phy->miphy_rst);
@@ -917,8 +923,9 @@ static int miphy28lp_init_sata(struct miphy28lp_phy *miphy_phy)
struct miphy28lp_dev *miphy_dev = miphy_phy->phydev;
int err, sata_conf = SATA_CTRL_SELECT_SATA;
- if ((!miphy_phy->syscfg_sata) || (!miphy_phy->syscfg_pci)
- || (!miphy_phy->base))
+ if ((!miphy_phy->syscfg_reg[SYSCFG_SATA]) ||
+ (!miphy_phy->syscfg_reg[SYSCFG_PCI]) ||
+ (!miphy_phy->base))
return -EINVAL;
dev_info(miphy_dev->dev, "sata-up mode, addr 0x%p\n", miphy_phy->base);
@@ -926,10 +933,11 @@ static int miphy28lp_init_sata(struct miphy28lp_phy *miphy_phy)
/* Configure the glue-logic */
sata_conf |= ((miphy_phy->sata_gen - SATA_GEN1) << SATA_SPDMODE);
- regmap_update_bits(miphy_dev->regmap, miphy_phy->syscfg_sata,
+ regmap_update_bits(miphy_dev->regmap,
+ miphy_phy->syscfg_reg[SYSCFG_SATA],
SATA_CTRL_MASK, sata_conf);
- regmap_update_bits(miphy_dev->regmap, miphy_phy->syscfg_pci,
+ regmap_update_bits(miphy_dev->regmap, miphy_phy->syscfg_reg[SYSCFG_PCI],
PCIE_CTRL_MASK, SATA_CTRL_SELECT_PCIE);
/* MiPHY path and clocking init */
@@ -951,17 +959,19 @@ static int miphy28lp_init_pcie(struct miphy28lp_phy *miphy_phy)
struct miphy28lp_dev *miphy_dev = miphy_phy->phydev;
int err;
- if ((!miphy_phy->syscfg_sata) || (!miphy_phy->syscfg_pci)
+ if ((!miphy_phy->syscfg_reg[SYSCFG_SATA]) ||
+ (!miphy_phy->syscfg_reg[SYSCFG_PCI])
|| (!miphy_phy->base) || (!miphy_phy->pipebase))
return -EINVAL;
dev_info(miphy_dev->dev, "pcie-up mode, addr 0x%p\n", miphy_phy->base);
/* Configure the glue-logic */
- regmap_update_bits(miphy_dev->regmap, miphy_phy->syscfg_sata,
+ regmap_update_bits(miphy_dev->regmap,
+ miphy_phy->syscfg_reg[SYSCFG_SATA],
SATA_CTRL_MASK, SATA_CTRL_SELECT_PCIE);
- regmap_update_bits(miphy_dev->regmap, miphy_phy->syscfg_pci,
+ regmap_update_bits(miphy_dev->regmap, miphy_phy->syscfg_reg[SYSCFG_PCI],
PCIE_CTRL_MASK, SYSCFG_PCIE_PCIE_VAL);
/* MiPHY path and clocking init */
@@ -1156,7 +1166,8 @@ static int miphy28lp_probe_resets(struct device_node *node,
static int miphy28lp_of_probe(struct device_node *np,
struct miphy28lp_phy *miphy_phy)
{
- struct resource res;
+ int i;
+ u32 ctrlreg;
miphy_phy->osc_force_ext =
of_property_read_bool(np, "st,osc-force-ext");
@@ -1175,18 +1186,10 @@ static int miphy28lp_of_probe(struct device_node *np,
if (!miphy_phy->sata_gen)
miphy_phy->sata_gen = SATA_GEN1;
- if (!miphy28lp_get_resource_byname(np, "miphy-ctrl-glue", &res))
- miphy_phy->syscfg_miphy_ctrl = res.start;
-
- if (!miphy28lp_get_resource_byname(np, "miphy-status-glue", &res))
- miphy_phy->syscfg_miphy_status = res.start;
-
- if (!miphy28lp_get_resource_byname(np, "pcie-glue", &res))
- miphy_phy->syscfg_pci = res.start;
-
- if (!miphy28lp_get_resource_byname(np, "sata-glue", &res))
- miphy_phy->syscfg_sata = res.start;
-
+ for (i = 0; i < SYSCFG_REG_MAX; i++) {
+ if (!of_property_read_u32_index(np, "st,syscfg", i, &ctrlreg))
+ miphy_phy->syscfg_reg[i] = ctrlreg;
+ }
return 0;
}
--
1.7.9.5
^ permalink raw reply related [flat|nested] 11+ messages in thread* [PATCH 5/9] phy: phy-stih407-usb: Pass sysconfig register offsets via syscfg property.
2015-01-31 14:28 [GIT PULL 0/9] phy: for 3.20 merge window Kishon Vijay Abraham I
` (3 preceding siblings ...)
2015-01-31 14:28 ` [PATCH 4/9] phy: miphy28lp: Pass sysconfig register offsets via syscfg dt property Kishon Vijay Abraham I
@ 2015-01-31 14:28 ` Kishon Vijay Abraham I
2015-01-31 14:28 ` [PATCH 6/9] Documentation: bindings: add dt documentation for Rockchip usb PHY Kishon Vijay Abraham I
` (4 subsequent siblings)
9 siblings, 0 replies; 11+ messages in thread
From: Kishon Vijay Abraham I @ 2015-01-31 14:28 UTC (permalink / raw)
To: gregkh; +Cc: kishon, linux-kernel
From: Peter Griffin <peter.griffin@linaro.org>
Based on Arnds review comments here https://lkml.org/lkml/2014/11/13/161,
update the phy driver to not use the reg property to access the sysconfig
register offsets.
This is because other phy's (miphy28, miphy365) have a combination of
memory mapped registers and sysconfig control regs, and we shouldn't
be mixing address spaces in the reg property. In addition we would
ideally like the sysconfig offsets to be passed via DT in a uniform way.
This new method will also allow us to support devices which have sysconfig
registers in different banks more easily and it is also analagous to how
keystone and bcm7745 platforms pass there syscon offsets in DT.
This breaks DT compatibility, but this platform is considered WIP, and
is only used by a few developers who are upstreaming support for it.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
---
.../devicetree/bindings/phy/phy-stih407-usb.txt | 10 ++------
drivers/phy/phy-stih407-usb.c | 25 +++++++++++---------
2 files changed, 16 insertions(+), 19 deletions(-)
diff --git a/Documentation/devicetree/bindings/phy/phy-stih407-usb.txt b/Documentation/devicetree/bindings/phy/phy-stih407-usb.txt
index 1ef8228..de6a706 100644
--- a/Documentation/devicetree/bindings/phy/phy-stih407-usb.txt
+++ b/Documentation/devicetree/bindings/phy/phy-stih407-usb.txt
@@ -5,10 +5,7 @@ host controllers (when controlling usb2/1.1 devices) available on STiH407 SoC fa
Required properties:
- compatible : should be "st,stih407-usb2-phy"
-- reg : contain the offset and length of the system configuration registers
- used as glue logic to control & parameter phy
-- reg-names : the names of the system configuration registers in "reg", should be "param" and "reg"
-- st,syscfg : sysconfig register to manage phy parameter at driver level
+- st,syscfg : phandle of sysconfig bank plus integer array containing phyparam and phyctrl register offsets
- resets : list of phandle and reset specifier pairs. There should be two entries, one
for the whole phy and one for the port
- reset-names : list of reset signal names. Should be "global" and "port"
@@ -19,11 +16,8 @@ Example:
usb2_picophy0: usbpicophy@f8 {
compatible = "st,stih407-usb2-phy";
- reg = <0xf8 0x04>, /* syscfg 5062 */
- <0xf4 0x04>; /* syscfg 5061 */
- reg-names = "param", "ctrl";
#phy-cells = <0>;
- st,syscfg = <&syscfg_core>;
+ st,syscfg = <&syscfg_core 0x100 0xf4>;
resets = <&softreset STIH407_PICOPHY_SOFTRESET>,
<&picophyreset STIH407_PICOPHY0_RESET>;
reset-names = "global", "port";
diff --git a/drivers/phy/phy-stih407-usb.c b/drivers/phy/phy-stih407-usb.c
index 74f0fab..1d5ae5f 100644
--- a/drivers/phy/phy-stih407-usb.c
+++ b/drivers/phy/phy-stih407-usb.c
@@ -22,6 +22,9 @@
#include <linux/mfd/syscon.h>
#include <linux/phy/phy.h>
+#define PHYPARAM_REG 1
+#define PHYCTRL_REG 2
+
/* Default PHY_SEL and REFCLKSEL configuration */
#define STIH407_USB_PICOPHY_CTRL_PORT_CONF 0x6
#define STIH407_USB_PICOPHY_CTRL_PORT_MASK 0x1f
@@ -93,7 +96,7 @@ static int stih407_usb2_picophy_probe(struct platform_device *pdev)
struct device_node *np = dev->of_node;
struct phy_provider *phy_provider;
struct phy *phy;
- struct resource *res;
+ int ret;
phy_dev = devm_kzalloc(dev, sizeof(*phy_dev), GFP_KERNEL);
if (!phy_dev)
@@ -123,19 +126,19 @@ static int stih407_usb2_picophy_probe(struct platform_device *pdev)
return PTR_ERR(phy_dev->regmap);
}
- res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "ctrl");
- if (!res) {
- dev_err(dev, "No ctrl reg found\n");
- return -ENXIO;
+ ret = of_property_read_u32_index(np, "st,syscfg", PHYPARAM_REG,
+ &phy_dev->param);
+ if (ret) {
+ dev_err(dev, "can't get phyparam offset (%d)\n", ret);
+ return ret;
}
- phy_dev->ctrl = res->start;
- res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "param");
- if (!res) {
- dev_err(dev, "No param reg found\n");
- return -ENXIO;
+ ret = of_property_read_u32_index(np, "st,syscfg", PHYCTRL_REG,
+ &phy_dev->ctrl);
+ if (ret) {
+ dev_err(dev, "can't get phyctrl offset (%d)\n", ret);
+ return ret;
}
- phy_dev->param = res->start;
phy = devm_phy_create(dev, NULL, &stih407_usb2_picophy_data);
if (IS_ERR(phy)) {
--
1.7.9.5
^ permalink raw reply related [flat|nested] 11+ messages in thread* [PATCH 6/9] Documentation: bindings: add dt documentation for Rockchip usb PHY
2015-01-31 14:28 [GIT PULL 0/9] phy: for 3.20 merge window Kishon Vijay Abraham I
` (4 preceding siblings ...)
2015-01-31 14:28 ` [PATCH 5/9] phy: phy-stih407-usb: Pass sysconfig register offsets via syscfg property Kishon Vijay Abraham I
@ 2015-01-31 14:28 ` Kishon Vijay Abraham I
2015-01-31 14:28 ` [PATCH 7/9] phy: add a driver for the Rockchip SoC internal USB2.0 PHY Kishon Vijay Abraham I
` (3 subsequent siblings)
9 siblings, 0 replies; 11+ messages in thread
From: Kishon Vijay Abraham I @ 2015-01-31 14:28 UTC (permalink / raw)
To: gregkh; +Cc: kishon, linux-kernel
From: Yunzhi Li <lyz@rock-chips.com>
This patch adds a binding that describes the Rockchip usb PHYs
found on Rockchip SoCs usb interface.
Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
---
.../devicetree/bindings/phy/rockchip-usb-phy.txt | 37 ++++++++++++++++++++
1 file changed, 37 insertions(+)
create mode 100644 Documentation/devicetree/bindings/phy/rockchip-usb-phy.txt
diff --git a/Documentation/devicetree/bindings/phy/rockchip-usb-phy.txt b/Documentation/devicetree/bindings/phy/rockchip-usb-phy.txt
new file mode 100644
index 0000000..826454a
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/rockchip-usb-phy.txt
@@ -0,0 +1,37 @@
+ROCKCHIP USB2 PHY
+
+Required properties:
+ - compatible: rockchip,rk3288-usb-phy
+ - rockchip,grf : phandle to the syscon managing the "general
+ register files"
+ - #address-cells: should be 1
+ - #size-cells: should be 0
+
+Sub-nodes:
+Each PHY should be represented as a sub-node.
+
+Sub-nodes
+required properties:
+- #phy-cells: should be 0
+- reg: PHY configure reg address offset in GRF
+ "0x320" - for PHY attach to OTG controller
+ "0x334" - for PHY attach to HOST0 controller
+ "0x348" - for PHY attach to HOST1 controller
+
+Optional Properties:
+- clocks : phandle + clock specifier for the phy clocks
+- clock-names: string, clock name, must be "phyclk"
+
+Example:
+
+usbphy: phy {
+ compatible = "rockchip,rk3288-usb-phy";
+ rockchip,grf = <&grf>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ usbphy0: usb-phy0 {
+ #phy-cells = <0>;
+ reg = <0x320>;
+ };
+};
--
1.7.9.5
^ permalink raw reply related [flat|nested] 11+ messages in thread* [PATCH 7/9] phy: add a driver for the Rockchip SoC internal USB2.0 PHY
2015-01-31 14:28 [GIT PULL 0/9] phy: for 3.20 merge window Kishon Vijay Abraham I
` (5 preceding siblings ...)
2015-01-31 14:28 ` [PATCH 6/9] Documentation: bindings: add dt documentation for Rockchip usb PHY Kishon Vijay Abraham I
@ 2015-01-31 14:28 ` Kishon Vijay Abraham I
2015-01-31 14:28 ` [PATCH 8/9] phy: exynos-video-mipi: Fix regression by adding support for PMU regmap Kishon Vijay Abraham I
` (2 subsequent siblings)
9 siblings, 0 replies; 11+ messages in thread
From: Kishon Vijay Abraham I @ 2015-01-31 14:28 UTC (permalink / raw)
To: gregkh; +Cc: kishon, linux-kernel
From: Yunzhi Li <lyz@rock-chips.com>
This patch to add a generic PHY driver for ROCKCHIP usb PHYs,
currently this driver can support RK3288. The RK3288 SoC have
three independent USB PHY IPs which are all configured through a
set of registers located in the GRF (general register files)
module.
Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
---
drivers/phy/Kconfig | 7 ++
drivers/phy/Makefile | 1 +
drivers/phy/phy-rockchip-usb.c | 158 ++++++++++++++++++++++++++++++++++++++++
3 files changed, 166 insertions(+)
create mode 100644 drivers/phy/phy-rockchip-usb.c
diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
index ccad880..b24500a 100644
--- a/drivers/phy/Kconfig
+++ b/drivers/phy/Kconfig
@@ -239,6 +239,13 @@ config PHY_QCOM_IPQ806X_SATA
depends on OF
select GENERIC_PHY
+config PHY_ROCKCHIP_USB
+ tristate "Rockchip USB2 PHY Driver"
+ depends on ARCH_ROCKCHIP && OF
+ select GENERIC_PHY
+ help
+ Enable this to support the Rockchip USB 2.0 PHY.
+
config PHY_ST_SPEAR1310_MIPHY
tristate "ST SPEAR1310-MIPHY driver"
select GENERIC_PHY
diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
index aa74f96..48bf5a1 100644
--- a/drivers/phy/Makefile
+++ b/drivers/phy/Makefile
@@ -28,6 +28,7 @@ phy-exynos-usb2-$(CONFIG_PHY_EXYNOS5250_USB2) += phy-exynos5250-usb2.o
phy-exynos-usb2-$(CONFIG_PHY_S5PV210_USB2) += phy-s5pv210-usb2.o
obj-$(CONFIG_PHY_EXYNOS5_USBDRD) += phy-exynos5-usbdrd.o
obj-$(CONFIG_PHY_QCOM_APQ8064_SATA) += phy-qcom-apq8064-sata.o
+obj-$(CONFIG_PHY_ROCKCHIP_USB) += phy-rockchip-usb.o
obj-$(CONFIG_PHY_QCOM_IPQ806X_SATA) += phy-qcom-ipq806x-sata.o
obj-$(CONFIG_PHY_ST_SPEAR1310_MIPHY) += phy-spear1310-miphy.o
obj-$(CONFIG_PHY_ST_SPEAR1340_MIPHY) += phy-spear1340-miphy.o
diff --git a/drivers/phy/phy-rockchip-usb.c b/drivers/phy/phy-rockchip-usb.c
new file mode 100644
index 0000000..22011c3
--- /dev/null
+++ b/drivers/phy/phy-rockchip-usb.c
@@ -0,0 +1,158 @@
+/*
+ * Rockchip usb PHY driver
+ *
+ * Copyright (C) 2014 Yunzhi Li <lyz@rock-chips.com>
+ * Copyright (C) 2014 ROCKCHIP, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/consumer.h>
+#include <linux/reset.h>
+#include <linux/regmap.h>
+#include <linux/mfd/syscon.h>
+
+/*
+ * The higher 16-bit of this register is used for write protection
+ * only if BIT(13 + 16) set to 1 the BIT(13) can be written.
+ */
+#define SIDDQ_WRITE_ENA BIT(29)
+#define SIDDQ_ON BIT(13)
+#define SIDDQ_OFF (0 << 13)
+
+struct rockchip_usb_phy {
+ unsigned int reg_offset;
+ struct regmap *reg_base;
+ struct clk *clk;
+ struct phy *phy;
+};
+
+static int rockchip_usb_phy_power(struct rockchip_usb_phy *phy,
+ bool siddq)
+{
+ return regmap_write(phy->reg_base, phy->reg_offset,
+ SIDDQ_WRITE_ENA | (siddq ? SIDDQ_ON : SIDDQ_OFF));
+}
+
+static int rockchip_usb_phy_power_off(struct phy *_phy)
+{
+ struct rockchip_usb_phy *phy = phy_get_drvdata(_phy);
+ int ret = 0;
+
+ /* Power down usb phy analog blocks by set siddq 1 */
+ ret = rockchip_usb_phy_power(phy, 1);
+ if (ret)
+ return ret;
+
+ clk_disable_unprepare(phy->clk);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static int rockchip_usb_phy_power_on(struct phy *_phy)
+{
+ struct rockchip_usb_phy *phy = phy_get_drvdata(_phy);
+ int ret = 0;
+
+ ret = clk_prepare_enable(phy->clk);
+ if (ret)
+ return ret;
+
+ /* Power up usb phy analog blocks by set siddq 0 */
+ ret = rockchip_usb_phy_power(phy, 0);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static struct phy_ops ops = {
+ .power_on = rockchip_usb_phy_power_on,
+ .power_off = rockchip_usb_phy_power_off,
+ .owner = THIS_MODULE,
+};
+
+static int rockchip_usb_phy_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct rockchip_usb_phy *rk_phy;
+ struct phy_provider *phy_provider;
+ struct device_node *child;
+ struct regmap *grf;
+ unsigned int reg_offset;
+
+ grf = syscon_regmap_lookup_by_phandle(dev->of_node, "rockchip,grf");
+ if (IS_ERR(grf)) {
+ dev_err(&pdev->dev, "Missing rockchip,grf property\n");
+ return PTR_ERR(grf);
+ }
+
+ for_each_available_child_of_node(dev->of_node, child) {
+ rk_phy = devm_kzalloc(dev, sizeof(*rk_phy), GFP_KERNEL);
+ if (!rk_phy)
+ return -ENOMEM;
+
+ if (of_property_read_u32(child, "reg", ®_offset)) {
+ dev_err(dev, "missing reg property in node %s\n",
+ child->name);
+ return -EINVAL;
+ }
+
+ rk_phy->reg_offset = reg_offset;
+ rk_phy->reg_base = grf;
+
+ rk_phy->clk = of_clk_get_by_name(child, "phyclk");
+ if (IS_ERR(rk_phy->clk))
+ rk_phy->clk = NULL;
+
+ rk_phy->phy = devm_phy_create(dev, child, &ops);
+ if (IS_ERR(rk_phy->phy)) {
+ dev_err(dev, "failed to create PHY\n");
+ return PTR_ERR(rk_phy->phy);
+ }
+ phy_set_drvdata(rk_phy->phy, rk_phy);
+ }
+
+ phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+ return PTR_ERR_OR_ZERO(phy_provider);
+}
+
+static const struct of_device_id rockchip_usb_phy_dt_ids[] = {
+ { .compatible = "rockchip,rk3288-usb-phy" },
+ {}
+};
+
+MODULE_DEVICE_TABLE(of, rockchip_usb_phy_dt_ids);
+
+static struct platform_driver rockchip_usb_driver = {
+ .probe = rockchip_usb_phy_probe,
+ .driver = {
+ .name = "rockchip-usb-phy",
+ .owner = THIS_MODULE,
+ .of_match_table = rockchip_usb_phy_dt_ids,
+ },
+};
+
+module_platform_driver(rockchip_usb_driver);
+
+MODULE_AUTHOR("Yunzhi Li <lyz@rock-chips.com>");
+MODULE_DESCRIPTION("Rockchip USB 2.0 PHY driver");
+MODULE_LICENSE("GPL v2");
--
1.7.9.5
^ permalink raw reply related [flat|nested] 11+ messages in thread* [PATCH 8/9] phy: exynos-video-mipi: Fix regression by adding support for PMU regmap
2015-01-31 14:28 [GIT PULL 0/9] phy: for 3.20 merge window Kishon Vijay Abraham I
` (6 preceding siblings ...)
2015-01-31 14:28 ` [PATCH 7/9] phy: add a driver for the Rockchip SoC internal USB2.0 PHY Kishon Vijay Abraham I
@ 2015-01-31 14:28 ` Kishon Vijay Abraham I
2015-01-31 14:28 ` [PATCH 9/9] phy: miphy365x: Pass sysconfig register offsets via syscfg dt property Kishon Vijay Abraham I
2015-01-31 16:54 ` [GIT PULL 0/9] phy: for 3.20 merge window Greg KH
9 siblings, 0 replies; 11+ messages in thread
From: Kishon Vijay Abraham I @ 2015-01-31 14:28 UTC (permalink / raw)
To: gregkh; +Cc: kishon, linux-kernel
From: Sylwester Nawrocki <s.nawrocki@samsung.com>
After the Exynos Power Management Unit (PMU) driver was converted
to the platform device driver in commit 14fc8b93d47323561edf5d482
("ARM: EXYNOS: Add platform driver support for Exynos PMU") and
then PMU device nodes added to Exynos4 DTs in commit
7b9613aca42a5522d269 ("ARM: dts: add PMU syscon node for exynos4")
the mipi video phy driver started failing probing, due to overlapping
memory mapped register region resources.
Now all the Exynos peripheral devices which have registers in the PMU
region are supposed to use the regmap provided by the syscon driver.
So support for regmap is added in this patch, this unfortunately
creates yet another indirection into that supposedly trivial driver.
The additional mutex is required because single register is used by
PHY pairs (they share bit in a register). An improvement here could
be to allow a PHY instance be created with a driver custom mutex,
which would then be common for each PHY pair. This would eliminate
one of 3 mutexes which need to be taken in the phy_power_on/
phy_power_off code path. However, I tried to keep this bug fix patch
possibly simple.
This change is needed to make MIPI DSI displays and MIPI CSI-2
camera sensors working again on Exynos4 boards.
Cc: Pankaj Dubey <pankaj.dubey@samsung.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
---
.../devicetree/bindings/phy/samsung-phy.txt | 2 +-
drivers/phy/phy-exynos-mipi-video.c | 89 +++++++++++++-------
include/linux/mfd/syscon/exynos4-pmu.h | 21 +++++
3 files changed, 79 insertions(+), 33 deletions(-)
create mode 100644 include/linux/mfd/syscon/exynos4-pmu.h
diff --git a/Documentation/devicetree/bindings/phy/samsung-phy.txt b/Documentation/devicetree/bindings/phy/samsung-phy.txt
index d5bad92..91e38cf 100644
--- a/Documentation/devicetree/bindings/phy/samsung-phy.txt
+++ b/Documentation/devicetree/bindings/phy/samsung-phy.txt
@@ -3,8 +3,8 @@ Samsung S5P/EXYNOS SoC series MIPI CSIS/DSIM DPHY
Required properties:
- compatible : should be "samsung,s5pv210-mipi-video-phy";
-- reg : offset and length of the MIPI DPHY register set;
- #phy-cells : from the generic phy bindings, must be 1;
+- syscon - phandle to the PMU system controller;
For "samsung,s5pv210-mipi-video-phy" compatible PHYs the second cell in
the PHY specifier identifies the PHY and its meaning is as follows:
diff --git a/drivers/phy/phy-exynos-mipi-video.c b/drivers/phy/phy-exynos-mipi-video.c
index 943e0f8..f017b2f 100644
--- a/drivers/phy/phy-exynos-mipi-video.c
+++ b/drivers/phy/phy-exynos-mipi-video.c
@@ -12,19 +12,18 @@
#include <linux/err.h>
#include <linux/io.h>
#include <linux/kernel.h>
+#include <linux/mfd/syscon/exynos4-pmu.h>
#include <linux/module.h>
#include <linux/of.h>
#include <linux/of_address.h>
#include <linux/phy/phy.h>
#include <linux/platform_device.h>
+#include <linux/regmap.h>
#include <linux/spinlock.h>
+#include <linux/mfd/syscon.h>
-/* MIPI_PHYn_CONTROL register offset: n = 0..1 */
+/* MIPI_PHYn_CONTROL reg. offset (for base address from ioremap): n = 0..1 */
#define EXYNOS_MIPI_PHY_CONTROL(n) ((n) * 4)
-#define EXYNOS_MIPI_PHY_ENABLE (1 << 0)
-#define EXYNOS_MIPI_PHY_SRESETN (1 << 1)
-#define EXYNOS_MIPI_PHY_MRESETN (1 << 2)
-#define EXYNOS_MIPI_PHY_RESET_MASK (3 << 1)
enum exynos_mipi_phy_id {
EXYNOS_MIPI_PHY_ID_CSIS0,
@@ -38,43 +37,62 @@ enum exynos_mipi_phy_id {
((id) == EXYNOS_MIPI_PHY_ID_DSIM0 || (id) == EXYNOS_MIPI_PHY_ID_DSIM1)
struct exynos_mipi_video_phy {
- spinlock_t slock;
struct video_phy_desc {
struct phy *phy;
unsigned int index;
} phys[EXYNOS_MIPI_PHYS_NUM];
+ spinlock_t slock;
void __iomem *regs;
+ struct mutex mutex;
+ struct regmap *regmap;
};
static int __set_phy_state(struct exynos_mipi_video_phy *state,
enum exynos_mipi_phy_id id, unsigned int on)
{
+ const unsigned int offset = EXYNOS4_MIPI_PHY_CONTROL(id / 2);
void __iomem *addr;
- u32 reg, reset;
-
- addr = state->regs + EXYNOS_MIPI_PHY_CONTROL(id / 2);
+ u32 val, reset;
if (is_mipi_dsim_phy_id(id))
- reset = EXYNOS_MIPI_PHY_MRESETN;
- else
- reset = EXYNOS_MIPI_PHY_SRESETN;
-
- spin_lock(&state->slock);
- reg = readl(addr);
- if (on)
- reg |= reset;
+ reset = EXYNOS4_MIPI_PHY_MRESETN;
else
- reg &= ~reset;
- writel(reg, addr);
-
- /* Clear ENABLE bit only if MRESETN, SRESETN bits are not set. */
- if (on)
- reg |= EXYNOS_MIPI_PHY_ENABLE;
- else if (!(reg & EXYNOS_MIPI_PHY_RESET_MASK))
- reg &= ~EXYNOS_MIPI_PHY_ENABLE;
+ reset = EXYNOS4_MIPI_PHY_SRESETN;
+
+ if (state->regmap) {
+ mutex_lock(&state->mutex);
+ regmap_read(state->regmap, offset, &val);
+ if (on)
+ val |= reset;
+ else
+ val &= ~reset;
+ regmap_write(state->regmap, offset, val);
+ if (on)
+ val |= EXYNOS4_MIPI_PHY_ENABLE;
+ else if (!(val & EXYNOS4_MIPI_PHY_RESET_MASK))
+ val &= ~EXYNOS4_MIPI_PHY_ENABLE;
+ regmap_write(state->regmap, offset, val);
+ mutex_unlock(&state->mutex);
+ } else {
+ addr = state->regs + EXYNOS_MIPI_PHY_CONTROL(id / 2);
+
+ spin_lock(&state->slock);
+ val = readl(addr);
+ if (on)
+ val |= reset;
+ else
+ val &= ~reset;
+ writel(val, addr);
+ /* Clear ENABLE bit only if MRESETN, SRESETN bits are not set */
+ if (on)
+ val |= EXYNOS4_MIPI_PHY_ENABLE;
+ else if (!(val & EXYNOS4_MIPI_PHY_RESET_MASK))
+ val &= ~EXYNOS4_MIPI_PHY_ENABLE;
+
+ writel(val, addr);
+ spin_unlock(&state->slock);
+ }
- writel(reg, addr);
- spin_unlock(&state->slock);
return 0;
}
@@ -118,7 +136,6 @@ static int exynos_mipi_video_phy_probe(struct platform_device *pdev)
{
struct exynos_mipi_video_phy *state;
struct device *dev = &pdev->dev;
- struct resource *res;
struct phy_provider *phy_provider;
unsigned int i;
@@ -126,14 +143,22 @@ static int exynos_mipi_video_phy_probe(struct platform_device *pdev)
if (!state)
return -ENOMEM;
- res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ state->regmap = syscon_regmap_lookup_by_phandle(dev->of_node, "syscon");
+ if (IS_ERR(state->regmap)) {
+ struct resource *res;
- state->regs = devm_ioremap_resource(dev, res);
- if (IS_ERR(state->regs))
- return PTR_ERR(state->regs);
+ dev_info(dev, "regmap lookup failed: %ld\n",
+ PTR_ERR(state->regmap));
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ state->regs = devm_ioremap_resource(dev, res);
+ if (IS_ERR(state->regs))
+ return PTR_ERR(state->regs);
+ }
dev_set_drvdata(dev, state);
spin_lock_init(&state->slock);
+ mutex_init(&state->mutex);
for (i = 0; i < EXYNOS_MIPI_PHYS_NUM; i++) {
struct phy *phy = devm_phy_create(dev, NULL,
diff --git a/include/linux/mfd/syscon/exynos4-pmu.h b/include/linux/mfd/syscon/exynos4-pmu.h
new file mode 100644
index 0000000..278b1b1
--- /dev/null
+++ b/include/linux/mfd/syscon/exynos4-pmu.h
@@ -0,0 +1,21 @@
+/*
+ * Copyright (C) 2015 Samsung Electronics Co., Ltd.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef _LINUX_MFD_SYSCON_PMU_EXYNOS4_H_
+#define _LINUX_MFD_SYSCON_PMU_EXYNOS4_H_
+
+/* Exynos4 PMU register definitions */
+
+/* MIPI_PHYn_CONTROL register offset: n = 0..1 */
+#define EXYNOS4_MIPI_PHY_CONTROL(n) (0x710 + (n) * 4)
+#define EXYNOS4_MIPI_PHY_ENABLE (1 << 0)
+#define EXYNOS4_MIPI_PHY_SRESETN (1 << 1)
+#define EXYNOS4_MIPI_PHY_MRESETN (1 << 2)
+#define EXYNOS4_MIPI_PHY_RESET_MASK (3 << 1)
+
+#endif /* _LINUX_MFD_SYSCON_PMU_EXYNOS4_H_ */
--
1.7.9.5
^ permalink raw reply related [flat|nested] 11+ messages in thread* [PATCH 9/9] phy: miphy365x: Pass sysconfig register offsets via syscfg dt property.
2015-01-31 14:28 [GIT PULL 0/9] phy: for 3.20 merge window Kishon Vijay Abraham I
` (7 preceding siblings ...)
2015-01-31 14:28 ` [PATCH 8/9] phy: exynos-video-mipi: Fix regression by adding support for PMU regmap Kishon Vijay Abraham I
@ 2015-01-31 14:28 ` Kishon Vijay Abraham I
2015-01-31 16:54 ` [GIT PULL 0/9] phy: for 3.20 merge window Greg KH
9 siblings, 0 replies; 11+ messages in thread
From: Kishon Vijay Abraham I @ 2015-01-31 14:28 UTC (permalink / raw)
To: gregkh; +Cc: kishon, linux-kernel
From: Peter Griffin <peter.griffin@linaro.org>
Based on Arnds review comments here https://lkml.org/lkml/2014/11/13/161,
update the miphy365 phy driver to access sysconfig register offsets via
syscfg dt property.
This is because the reg property should not be mixing address spaces
like it does currently for miphy365. This change then also aligns us
to how other platforms such as keystone and bcm7445 pass there syscon
offsets via DT.
This patch breaks DT compatibility, but this platform is considered WIP,
and is only used by a few developers who are upstreaming support for it.
This change has been done as a single atomic commit to ensure it is
bisectable.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Tested-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
---
.../devicetree/bindings/phy/phy-miphy365x.txt | 15 +++++-----
arch/arm/boot/dts/stih416.dtsi | 10 +++----
drivers/phy/phy-miphy365x.c | 29 +++++++-------------
3 files changed, 23 insertions(+), 31 deletions(-)
diff --git a/Documentation/devicetree/bindings/phy/phy-miphy365x.txt b/Documentation/devicetree/bindings/phy/phy-miphy365x.txt
index 42c8808..9802d5d 100644
--- a/Documentation/devicetree/bindings/phy/phy-miphy365x.txt
+++ b/Documentation/devicetree/bindings/phy/phy-miphy365x.txt
@@ -6,8 +6,10 @@ for SATA and PCIe.
Required properties (controller (parent) node):
- compatible : Should be "st,miphy365x-phy"
-- st,syscfg : Should be a phandle of the system configuration register group
- which contain the SATA, PCIe mode setting bits
+- st,syscfg : Phandle / integer array property. Phandle of sysconfig group
+ containing the miphy registers and integer array should contain
+ an entry for each port sub-node, specifying the control
+ register offset inside the sysconfig group.
Required nodes : A sub-node is required for each channel the controller
provides. Address range information including the usual
@@ -26,7 +28,6 @@ Required properties (port (child) node):
registers filled in "reg":
- sata: For SATA devices
- pcie: For PCIe devices
- - syscfg: To specify the syscfg based config register
Optional properties (port (child) node):
- st,sata-gen : Generation of locally attached SATA IP. Expected values
@@ -39,20 +40,20 @@ Example:
miphy365x_phy: miphy365x@fe382000 {
compatible = "st,miphy365x-phy";
- st,syscfg = <&syscfg_rear>;
+ st,syscfg = <&syscfg_rear 0x824 0x828>;
#address-cells = <1>;
#size-cells = <1>;
ranges;
phy_port0: port@fe382000 {
- reg = <0xfe382000 0x100>, <0xfe394000 0x100>, <0x824 0x4>;
- reg-names = "sata", "pcie", "syscfg";
+ reg = <0xfe382000 0x100>, <0xfe394000 0x100>;
+ reg-names = "sata", "pcie";
#phy-cells = <1>;
st,sata-gen = <3>;
};
phy_port1: port@fe38a000 {
- reg = <0xfe38a000 0x100>, <0xfe804000 0x100>, <0x828 0x4>;;
+ reg = <0xfe38a000 0x100>, <0xfe804000 0x100>;;
reg-names = "sata", "pcie", "syscfg";
#phy-cells = <1>;
st,pcie-tx-pol-inv;
diff --git a/arch/arm/boot/dts/stih416.dtsi b/arch/arm/boot/dts/stih416.dtsi
index fad9073..85afe01 100644
--- a/arch/arm/boot/dts/stih416.dtsi
+++ b/arch/arm/boot/dts/stih416.dtsi
@@ -283,21 +283,21 @@
miphy365x_phy: phy@fe382000 {
compatible = "st,miphy365x-phy";
- st,syscfg = <&syscfg_rear>;
+ st,syscfg = <&syscfg_rear 0x824 0x828>;
#address-cells = <1>;
#size-cells = <1>;
ranges;
phy_port0: port@fe382000 {
#phy-cells = <1>;
- reg = <0xfe382000 0x100>, <0xfe394000 0x100>, <0x824 0x4>;
- reg-names = "sata", "pcie", "syscfg";
+ reg = <0xfe382000 0x100>, <0xfe394000 0x100>;
+ reg-names = "sata", "pcie";
};
phy_port1: port@fe38a000 {
#phy-cells = <1>;
- reg = <0xfe38a000 0x100>, <0xfe804000 0x100>, <0x828 0x4>;
- reg-names = "sata", "pcie", "syscfg";
+ reg = <0xfe38a000 0x100>, <0xfe804000 0x100>;
+ reg-names = "sata", "pcie";
};
};
diff --git a/drivers/phy/phy-miphy365x.c b/drivers/phy/phy-miphy365x.c
index 6ab43a8..6c80154 100644
--- a/drivers/phy/phy-miphy365x.c
+++ b/drivers/phy/phy-miphy365x.c
@@ -141,7 +141,7 @@ struct miphy365x_phy {
bool pcie_tx_pol_inv;
bool sata_tx_pol_inv;
u32 sata_gen;
- u64 ctrlreg;
+ u32 ctrlreg;
u8 type;
};
@@ -179,7 +179,7 @@ static int miphy365x_set_path(struct miphy365x_phy *miphy_phy,
bool sata = (miphy_phy->type == MIPHY_TYPE_SATA);
return regmap_update_bits(miphy_dev->regmap,
- (unsigned int)miphy_phy->ctrlreg,
+ miphy_phy->ctrlreg,
SYSCFG_SELECT_SATA_MASK,
sata << SYSCFG_SELECT_SATA_POS);
}
@@ -445,7 +445,6 @@ int miphy365x_get_addr(struct device *dev, struct miphy365x_phy *miphy_phy,
{
struct device_node *phynode = miphy_phy->phy->dev.of_node;
const char *name;
- const __be32 *taddr;
int type = miphy_phy->type;
int ret;
@@ -455,22 +454,6 @@ int miphy365x_get_addr(struct device *dev, struct miphy365x_phy *miphy_phy,
return ret;
}
- if (!strncmp(name, "syscfg", 6)) {
- taddr = of_get_address(phynode, index, NULL, NULL);
- if (!taddr) {
- dev_err(dev, "failed to fetch syscfg address\n");
- return -EINVAL;
- }
-
- miphy_phy->ctrlreg = of_translate_address(phynode, taddr);
- if (miphy_phy->ctrlreg == OF_BAD_ADDR) {
- dev_err(dev, "failed to translate syscfg address\n");
- return -EINVAL;
- }
-
- return 0;
- }
-
if (!((!strncmp(name, "sata", 4) && type == MIPHY_TYPE_SATA) ||
(!strncmp(name, "pcie", 4) && type == MIPHY_TYPE_PCIE)))
return 0;
@@ -606,7 +589,15 @@ static int miphy365x_probe(struct platform_device *pdev)
return ret;
phy_set_drvdata(phy, miphy_dev->phys[port]);
+
port++;
+ /* sysconfig offsets are indexed from 1 */
+ ret = of_property_read_u32_index(np, "st,syscfg", port,
+ &miphy_phy->ctrlreg);
+ if (ret) {
+ dev_err(&pdev->dev, "No sysconfig offset found\n");
+ return ret;
+ }
}
provider = devm_of_phy_provider_register(&pdev->dev, miphy365x_xlate);
--
1.7.9.5
^ permalink raw reply related [flat|nested] 11+ messages in thread* Re: [GIT PULL 0/9] phy: for 3.20 merge window
2015-01-31 14:28 [GIT PULL 0/9] phy: for 3.20 merge window Kishon Vijay Abraham I
` (8 preceding siblings ...)
2015-01-31 14:28 ` [PATCH 9/9] phy: miphy365x: Pass sysconfig register offsets via syscfg dt property Kishon Vijay Abraham I
@ 2015-01-31 16:54 ` Greg KH
9 siblings, 0 replies; 11+ messages in thread
From: Greg KH @ 2015-01-31 16:54 UTC (permalink / raw)
To: Kishon Vijay Abraham I; +Cc: linux-kernel
On Sat, Jan 31, 2015 at 07:58:07PM +0530, Kishon Vijay Abraham I wrote:
> Hi Greg,
>
> Please find the PULL REQUEST for 3.20 merge window. It's a rather
> short pull request which includes a new PHY driver for rockchip and contains few
> misc fixes.
>
> There is a patch which modifies the dt data for stih416 and I've included it
> in this pull request after getting ack from STI maintainer (Maxime Coquelin).
>
> Let me know If I have to change something.
>
> Cheers
> Kishon
>
> The following changes since commit ec6f34e5b552fb0a52e6aae1a5afbbb1605cc6cc:
>
> Linux 3.19-rc5 (2015-01-18 18:02:20 +1200)
>
> are available in the git repository at:
>
> git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy.git tags/for-3.20
Pulled and pushed out, thanks.
greg k-h
^ permalink raw reply [flat|nested] 11+ messages in thread