[PATCH 0/4] Few dm816x fixes and improvments

[PATCH 0/4] Few dm816x fixes and improvments

[Tony Lindgren]

Hi all,

Here are few dm816x related fixes and improvments. Mostly to get
GPIO interrupts working, and add DMA for the USB.

Note that the USB still depends on the USB PHY driver posted in
"[PATCH v2] phy: Add a driver for dm816x USB PHY".

Regards,

Tony


Tony Lindgren (4):
  ARM: dts: Fix gpio interrupts for dm816x
  ARM: dts: Fix typo for dm816x usb0_pins
  ARM: dts: Add cppi41 support for dm816x MUSB
  ARM: dts: Remove PIN_INPUT for dm816x McSPI

 arch/arm/boot/dts/dm8168-evm.dts | 33 +++++++++++++----
 arch/arm/boot/dts/dm816x.dtsi    | 78 +++++++++++++++++++++++++++++++++++++---
 2 files changed, 100 insertions(+), 11 deletions(-)

-- 
2.1.4

[PATCH 0/4] Few dm816x fixes and improvments

[Tony Lindgren]

Hi all,

Here are few dm816x related fixes and improvments. Mostly to get
GPIO interrupts working, and add DMA for the USB.

Note that the USB still depends on the USB PHY driver posted in
"[PATCH v2] phy: Add a driver for dm816x USB PHY".

Regards,

Tony


Tony Lindgren (4):
  ARM: dts: Fix gpio interrupts for dm816x
  ARM: dts: Fix typo for dm816x usb0_pins
  ARM: dts: Add cppi41 support for dm816x MUSB
  ARM: dts: Remove PIN_INPUT for dm816x McSPI

 arch/arm/boot/dts/dm8168-evm.dts | 33 +++++++++++++----
 arch/arm/boot/dts/dm816x.dtsi    | 78 +++++++++++++++++++++++++++++++++++++---
 2 files changed, 100 insertions(+), 11 deletions(-)

-- 
2.1.4

[PATCH 1/4] ARM: dts: Fix gpio interrupts for dm816x

[Tony Lindgren]

Commit 7800064ba507 ("ARM: dts: Add basic dm816x device tree
configuration") added basic devices for dm816x, but I was not able
to test the GPIO interrupts earlier until I found some suitable pins
to test with. We can mux the MMC card detect and write protect pins
from SD_SDCD and SD_SDWP mode to use a normal GPIO interrupts that
are also suitable for the MMC subsystem.

This turned out several issues that need to be fixed:

- I set the GPIO type wrong to be compatible with omap3 instead
  of omap4. The GPIO controller on dm816x has EOI interrupt
  register like omap4 and am335x.

- I got the GPIO interrupt numbers wrong as each bank has two
  and we only use one. They need to be set up the same way as
  on am335x.

- The gpio banks are missing interrupt controller related
  properties.

With these changes the GPIO interrupts can be used with the
MMC card detect pin, so let's wire that up. Let's also mux all
the MMC lines for completeness while at it.

For the first GPIO bank I tested using GPMC lines temporarily
muxed to GPIOs on the dip switch 10.

Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/boot/dts/dm8168-evm.dts | 19 +++++++++++++++++++
 arch/arm/boot/dts/dm816x.dtsi    | 18 ++++++++++++++----
 2 files changed, 33 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/dm8168-evm.dts b/arch/arm/boot/dts/dm8168-evm.dts
index d3a29c1..afe678f 100644
--- a/arch/arm/boot/dts/dm8168-evm.dts
+++ b/arch/arm/boot/dts/dm8168-evm.dts
@@ -36,6 +36,20 @@
 		>;
 	};
 
+	mmc_pins: pinmux_mmc_pins {
+		pinctrl-single,pins = <
+			DM816X_IOPAD(0x0a70, MUX_MODE0)			/* SD_POW */
+			DM816X_IOPAD(0x0a74, MUX_MODE0)			/* SD_CLK */
+			DM816X_IOPAD(0x0a78, MUX_MODE0)			/* SD_CMD */
+			DM816X_IOPAD(0x0a7C, MUX_MODE0)			/* SD_DAT0 */
+			DM816X_IOPAD(0x0a80, MUX_MODE0)			/* SD_DAT1 */
+			DM816X_IOPAD(0x0a84, MUX_MODE0)			/* SD_DAT2 */
+			DM816X_IOPAD(0x0a88, MUX_MODE0)			/* SD_DAT2 */
+			DM816X_IOPAD(0x0a8c, MUX_MODE2)			/* GP1[7] */
+			DM816X_IOPAD(0x0a90, MUX_MODE2)			/* GP1[8] */
+		>;
+	};
+
 	usb0_pins: pinmux_usb0_pins {
 		pinctrl-single,pins = <
 			DM816X_IOPAD(0x0d00, MUX_MODE0)			/* USB0_DRVVBUS */
@@ -137,7 +151,12 @@
 };
 
 &mmc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc_pins>;
 	vmmc-supply = <&vmmcsd_fixed>;
+	bus-width = <4>;
+	cd-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio2 8 GPIO_ACTIVE_LOW>;
 };
 
 /* At least dm8168-evm rev c won't support multipoint, later may */
diff --git a/arch/arm/boot/dts/dm816x.dtsi b/arch/arm/boot/dts/dm816x.dtsi
index 3c97b5f..f35715b 100644
--- a/arch/arm/boot/dts/dm816x.dtsi
+++ b/arch/arm/boot/dts/dm816x.dtsi
@@ -150,17 +150,27 @@
 		};
 
 		gpio1: gpio@48032000 {
-			compatible = "ti,omap3-gpio";
+			compatible = "ti,omap4-gpio";
 			ti,hwmods = "gpio1";
+			ti,gpio-always-on;
 			reg = <0x48032000 0x1000>;
-			interrupts = <97>;
+			interrupts = <96>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
 		};
 
 		gpio2: gpio@4804c000 {
-			compatible = "ti,omap3-gpio";
+			compatible = "ti,omap4-gpio";
 			ti,hwmods = "gpio2";
+			ti,gpio-always-on;
 			reg = <0x4804c000 0x1000>;
-			interrupts = <99>;
+			interrupts = <98>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
 		};
 
 		gpmc: gpmc@50000000 {
-- 
2.1.4

[PATCH 1/4] ARM: dts: Fix gpio interrupts for dm816x

[Tony Lindgren]

Commit 7800064ba507 ("ARM: dts: Add basic dm816x device tree
configuration") added basic devices for dm816x, but I was not able
to test the GPIO interrupts earlier until I found some suitable pins
to test with. We can mux the MMC card detect and write protect pins
from SD_SDCD and SD_SDWP mode to use a normal GPIO interrupts that
are also suitable for the MMC subsystem.

This turned out several issues that need to be fixed:

- I set the GPIO type wrong to be compatible with omap3 instead
  of omap4. The GPIO controller on dm816x has EOI interrupt
  register like omap4 and am335x.

- I got the GPIO interrupt numbers wrong as each bank has two
  and we only use one. They need to be set up the same way as
  on am335x.

- The gpio banks are missing interrupt controller related
  properties.

With these changes the GPIO interrupts can be used with the
MMC card detect pin, so let's wire that up. Let's also mux all
the MMC lines for completeness while at it.

For the first GPIO bank I tested using GPMC lines temporarily
muxed to GPIOs on the dip switch 10.

Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/boot/dts/dm8168-evm.dts | 19 +++++++++++++++++++
 arch/arm/boot/dts/dm816x.dtsi    | 18 ++++++++++++++----
 2 files changed, 33 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/dm8168-evm.dts b/arch/arm/boot/dts/dm8168-evm.dts
index d3a29c1..afe678f 100644
--- a/arch/arm/boot/dts/dm8168-evm.dts
+++ b/arch/arm/boot/dts/dm8168-evm.dts
@@ -36,6 +36,20 @@
 		>;
 	};
 
+	mmc_pins: pinmux_mmc_pins {
+		pinctrl-single,pins = <
+			DM816X_IOPAD(0x0a70, MUX_MODE0)			/* SD_POW */
+			DM816X_IOPAD(0x0a74, MUX_MODE0)			/* SD_CLK */
+			DM816X_IOPAD(0x0a78, MUX_MODE0)			/* SD_CMD */
+			DM816X_IOPAD(0x0a7C, MUX_MODE0)			/* SD_DAT0 */
+			DM816X_IOPAD(0x0a80, MUX_MODE0)			/* SD_DAT1 */
+			DM816X_IOPAD(0x0a84, MUX_MODE0)			/* SD_DAT2 */
+			DM816X_IOPAD(0x0a88, MUX_MODE0)			/* SD_DAT2 */
+			DM816X_IOPAD(0x0a8c, MUX_MODE2)			/* GP1[7] */
+			DM816X_IOPAD(0x0a90, MUX_MODE2)			/* GP1[8] */
+		>;
+	};
+
 	usb0_pins: pinmux_usb0_pins {
 		pinctrl-single,pins = <
 			DM816X_IOPAD(0x0d00, MUX_MODE0)			/* USB0_DRVVBUS */
@@ -137,7 +151,12 @@
 };
 
 &mmc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc_pins>;
 	vmmc-supply = <&vmmcsd_fixed>;
+	bus-width = <4>;
+	cd-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio2 8 GPIO_ACTIVE_LOW>;
 };
 
 /* At least dm8168-evm rev c won't support multipoint, later may */
diff --git a/arch/arm/boot/dts/dm816x.dtsi b/arch/arm/boot/dts/dm816x.dtsi
index 3c97b5f..f35715b 100644
--- a/arch/arm/boot/dts/dm816x.dtsi
+++ b/arch/arm/boot/dts/dm816x.dtsi
@@ -150,17 +150,27 @@
 		};
 
 		gpio1: gpio at 48032000 {
-			compatible = "ti,omap3-gpio";
+			compatible = "ti,omap4-gpio";
 			ti,hwmods = "gpio1";
+			ti,gpio-always-on;
 			reg = <0x48032000 0x1000>;
-			interrupts = <97>;
+			interrupts = <96>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
 		};
 
 		gpio2: gpio at 4804c000 {
-			compatible = "ti,omap3-gpio";
+			compatible = "ti,omap4-gpio";
 			ti,hwmods = "gpio2";
+			ti,gpio-always-on;
 			reg = <0x4804c000 0x1000>;
-			interrupts = <99>;
+			interrupts = <98>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
 		};
 
 		gpmc: gpmc at 50000000 {
-- 
2.1.4

[PATCH 2/4] ARM: dts: Fix typo for dm816x usb0_pins

[Tony Lindgren]

Commit a54879a00859 ("ARM: dts: Fix USB dts configuration for dm816x")
attempted to fix the USB features introduced by commit 7800064ba507
("ARM: dts: Add basic dm816x device tree configuration") but obviously
I did not read the dmesg as more USB issues still keep trickling in.

It should be usb1_pins instead not usb0_pins for the second interface
to avoid warnings from pinctrl framework.

Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/boot/dts/dm8168-evm.dts | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/dm8168-evm.dts b/arch/arm/boot/dts/dm8168-evm.dts
index afe678f..b520a8b 100644
--- a/arch/arm/boot/dts/dm8168-evm.dts
+++ b/arch/arm/boot/dts/dm8168-evm.dts
@@ -52,13 +52,13 @@
 
 	usb0_pins: pinmux_usb0_pins {
 		pinctrl-single,pins = <
-			DM816X_IOPAD(0x0d00, MUX_MODE0)			/* USB0_DRVVBUS */
+			DM816X_IOPAD(0x0d04, MUX_MODE0)			/* USB0_DRVVBUS */
 		>;
 	};
 
-	usb1_pins: pinmux_usb0_pins {
+	usb1_pins: pinmux_usb1_pins {
 		pinctrl-single,pins = <
-			DM816X_IOPAD(0x0d04, MUX_MODE0)			/* USB1_DRVVBUS */
+			DM816X_IOPAD(0x0d08, MUX_MODE0)			/* USB1_DRVVBUS */
 		>;
 	};
 };
-- 
2.1.4

[PATCH 2/4] ARM: dts: Fix typo for dm816x usb0_pins

[Tony Lindgren]

Commit a54879a00859 ("ARM: dts: Fix USB dts configuration for dm816x")
attempted to fix the USB features introduced by commit 7800064ba507
("ARM: dts: Add basic dm816x device tree configuration") but obviously
I did not read the dmesg as more USB issues still keep trickling in.

It should be usb1_pins instead not usb0_pins for the second interface
to avoid warnings from pinctrl framework.

Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/boot/dts/dm8168-evm.dts | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/dm8168-evm.dts b/arch/arm/boot/dts/dm8168-evm.dts
index afe678f..b520a8b 100644
--- a/arch/arm/boot/dts/dm8168-evm.dts
+++ b/arch/arm/boot/dts/dm8168-evm.dts
@@ -52,13 +52,13 @@
 
 	usb0_pins: pinmux_usb0_pins {
 		pinctrl-single,pins = <
-			DM816X_IOPAD(0x0d00, MUX_MODE0)			/* USB0_DRVVBUS */
+			DM816X_IOPAD(0x0d04, MUX_MODE0)			/* USB0_DRVVBUS */
 		>;
 	};
 
-	usb1_pins: pinmux_usb0_pins {
+	usb1_pins: pinmux_usb1_pins {
 		pinctrl-single,pins = <
-			DM816X_IOPAD(0x0d04, MUX_MODE0)			/* USB1_DRVVBUS */
+			DM816X_IOPAD(0x0d08, MUX_MODE0)			/* USB1_DRVVBUS */
 		>;
 	};
 };
-- 
2.1.4

[PATCH 3/4] ARM: dts: Add cppi41 support for dm816x MUSB

[Tony Lindgren]

Looks like we have cppi41 on dm816x just like on am335x.

Cc: Bin Liu <binmlist@gmail.com>
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/boot/dts/dm816x.dtsi | 60 +++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 60 insertions(+)

diff --git a/arch/arm/boot/dts/dm816x.dtsi b/arch/arm/boot/dts/dm816x.dtsi
index f35715b..de8427b 100644
--- a/arch/arm/boot/dts/dm816x.dtsi
+++ b/arch/arm/boot/dts/dm816x.dtsi
@@ -396,6 +396,29 @@
 				mentor,num-eps = <16>;
 				mentor,ram-bits = <12>;
 				mentor,power = <500>;
+
+				dmas = <&cppi41dma  0 0 &cppi41dma  1 0
+					&cppi41dma  2 0 &cppi41dma  3 0
+					&cppi41dma  4 0 &cppi41dma  5 0
+					&cppi41dma  6 0 &cppi41dma  7 0
+					&cppi41dma  8 0 &cppi41dma  9 0
+					&cppi41dma 10 0 &cppi41dma 11 0
+					&cppi41dma 12 0 &cppi41dma 13 0
+					&cppi41dma 14 0 &cppi41dma  0 1
+					&cppi41dma  1 1 &cppi41dma  2 1
+					&cppi41dma  3 1 &cppi41dma  4 1
+					&cppi41dma  5 1 &cppi41dma  6 1
+					&cppi41dma  7 1 &cppi41dma  8 1
+					&cppi41dma  9 1 &cppi41dma 10 1
+					&cppi41dma 11 1 &cppi41dma 12 1
+					&cppi41dma 13 1 &cppi41dma 14 1>;
+				dma-names =
+					"rx1", "rx2", "rx3", "rx4", "rx5", "rx6", "rx7",
+					"rx8", "rx9", "rx10", "rx11", "rx12", "rx13",
+					"rx14", "rx15",
+					"tx1", "tx2", "tx3", "tx4", "tx5", "tx6", "tx7",
+					"tx8", "tx9", "tx10", "tx11", "tx12", "tx13",
+					"tx14", "tx15";
 			};
 
 			usb1: usb@47401800 {
@@ -413,6 +436,43 @@
 				mentor,num-eps = <16>;
 				mentor,ram-bits = <12>;
 				mentor,power = <500>;
+
+				dmas = <&cppi41dma 15 0 &cppi41dma 16 0
+					&cppi41dma 17 0 &cppi41dma 18 0
+					&cppi41dma 19 0 &cppi41dma 20 0
+					&cppi41dma 21 0 &cppi41dma 22 0
+					&cppi41dma 23 0 &cppi41dma 24 0
+					&cppi41dma 25 0 &cppi41dma 26 0
+					&cppi41dma 27 0 &cppi41dma 28 0
+					&cppi41dma 29 0 &cppi41dma 15 1
+					&cppi41dma 16 1 &cppi41dma 17 1
+					&cppi41dma 18 1 &cppi41dma 19 1
+					&cppi41dma 20 1 &cppi41dma 21 1
+					&cppi41dma 22 1 &cppi41dma 23 1
+					&cppi41dma 24 1 &cppi41dma 25 1
+					&cppi41dma 26 1 &cppi41dma 27 1
+					&cppi41dma 28 1 &cppi41dma 29 1>;
+				dma-names =
+					"rx1", "rx2", "rx3", "rx4", "rx5", "rx6", "rx7",
+					"rx8", "rx9", "rx10", "rx11", "rx12", "rx13",
+					"rx14", "rx15",
+					"tx1", "tx2", "tx3", "tx4", "tx5", "tx6", "tx7",
+					"tx8", "tx9", "tx10", "tx11", "tx12", "tx13",
+					"tx14", "tx15";
+			};
+
+			cppi41dma: dma-controller@47402000 {
+				compatible = "ti,am3359-cppi41";
+				reg =  <0x47400000 0x1000
+					0x47402000 0x1000
+					0x47403000 0x1000
+					0x47404000 0x4000>;
+				reg-names = "glue", "controller", "scheduler", "queuemgr";
+				interrupts = <17>;
+				interrupt-names = "glue";
+				#dma-cells = <2>;
+				#dma-channels = <30>;
+				#dma-requests = <256>;
 			};
 		};
 
-- 
2.1.4

[PATCH 3/4] ARM: dts: Add cppi41 support for dm816x MUSB

[Tony Lindgren]

Looks like we have cppi41 on dm816x just like on am335x.

Cc: Bin Liu <binmlist@gmail.com>
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/boot/dts/dm816x.dtsi | 60 +++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 60 insertions(+)

diff --git a/arch/arm/boot/dts/dm816x.dtsi b/arch/arm/boot/dts/dm816x.dtsi
index f35715b..de8427b 100644
--- a/arch/arm/boot/dts/dm816x.dtsi
+++ b/arch/arm/boot/dts/dm816x.dtsi
@@ -396,6 +396,29 @@
 				mentor,num-eps = <16>;
 				mentor,ram-bits = <12>;
 				mentor,power = <500>;
+
+				dmas = <&cppi41dma  0 0 &cppi41dma  1 0
+					&cppi41dma  2 0 &cppi41dma  3 0
+					&cppi41dma  4 0 &cppi41dma  5 0
+					&cppi41dma  6 0 &cppi41dma  7 0
+					&cppi41dma  8 0 &cppi41dma  9 0
+					&cppi41dma 10 0 &cppi41dma 11 0
+					&cppi41dma 12 0 &cppi41dma 13 0
+					&cppi41dma 14 0 &cppi41dma  0 1
+					&cppi41dma  1 1 &cppi41dma  2 1
+					&cppi41dma  3 1 &cppi41dma  4 1
+					&cppi41dma  5 1 &cppi41dma  6 1
+					&cppi41dma  7 1 &cppi41dma  8 1
+					&cppi41dma  9 1 &cppi41dma 10 1
+					&cppi41dma 11 1 &cppi41dma 12 1
+					&cppi41dma 13 1 &cppi41dma 14 1>;
+				dma-names =
+					"rx1", "rx2", "rx3", "rx4", "rx5", "rx6", "rx7",
+					"rx8", "rx9", "rx10", "rx11", "rx12", "rx13",
+					"rx14", "rx15",
+					"tx1", "tx2", "tx3", "tx4", "tx5", "tx6", "tx7",
+					"tx8", "tx9", "tx10", "tx11", "tx12", "tx13",
+					"tx14", "tx15";
 			};
 
 			usb1: usb at 47401800 {
@@ -413,6 +436,43 @@
 				mentor,num-eps = <16>;
 				mentor,ram-bits = <12>;
 				mentor,power = <500>;
+
+				dmas = <&cppi41dma 15 0 &cppi41dma 16 0
+					&cppi41dma 17 0 &cppi41dma 18 0
+					&cppi41dma 19 0 &cppi41dma 20 0
+					&cppi41dma 21 0 &cppi41dma 22 0
+					&cppi41dma 23 0 &cppi41dma 24 0
+					&cppi41dma 25 0 &cppi41dma 26 0
+					&cppi41dma 27 0 &cppi41dma 28 0
+					&cppi41dma 29 0 &cppi41dma 15 1
+					&cppi41dma 16 1 &cppi41dma 17 1
+					&cppi41dma 18 1 &cppi41dma 19 1
+					&cppi41dma 20 1 &cppi41dma 21 1
+					&cppi41dma 22 1 &cppi41dma 23 1
+					&cppi41dma 24 1 &cppi41dma 25 1
+					&cppi41dma 26 1 &cppi41dma 27 1
+					&cppi41dma 28 1 &cppi41dma 29 1>;
+				dma-names =
+					"rx1", "rx2", "rx3", "rx4", "rx5", "rx6", "rx7",
+					"rx8", "rx9", "rx10", "rx11", "rx12", "rx13",
+					"rx14", "rx15",
+					"tx1", "tx2", "tx3", "tx4", "tx5", "tx6", "tx7",
+					"tx8", "tx9", "tx10", "tx11", "tx12", "tx13",
+					"tx14", "tx15";
+			};
+
+			cppi41dma: dma-controller at 47402000 {
+				compatible = "ti,am3359-cppi41";
+				reg =  <0x47400000 0x1000
+					0x47402000 0x1000
+					0x47403000 0x1000
+					0x47404000 0x4000>;
+				reg-names = "glue", "controller", "scheduler", "queuemgr";
+				interrupts = <17>;
+				interrupt-names = "glue";
+				#dma-cells = <2>;
+				#dma-channels = <30>;
+				#dma-requests = <256>;
 			};
 		};
 
-- 
2.1.4

Re: [PATCH 3/4] ARM: dts: Add cppi41 support for dm816x MUSB

[Felipe Balbi]

[-- Attachment #1: Type: text/plain, Size: 434 bytes --]

Hi,

On Tue, Mar 17, 2015 at 05:19:20PM -0700, Tony Lindgren wrote:
> Looks like we have cppi41 on dm816x just like on am335x.
> 
> Cc: Bin Liu <binmlist@gmail.com>
> Cc: Brian Hutchinson <b.hutchman@gmail.com>
> Cc: Felipe Balbi <balbi@ti.com>
> Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
> Signed-off-by: Tony Lindgren <tony@atomide.com>

Any logs available ? Any throughput improvements with DMA ?

-- 
balbi

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]

[PATCH 3/4] ARM: dts: Add cppi41 support for dm816x MUSB

[Felipe Balbi]

Hi,

On Tue, Mar 17, 2015 at 05:19:20PM -0700, Tony Lindgren wrote:
> Looks like we have cppi41 on dm816x just like on am335x.
> 
> Cc: Bin Liu <binmlist@gmail.com>
> Cc: Brian Hutchinson <b.hutchman@gmail.com>
> Cc: Felipe Balbi <balbi@ti.com>
> Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
> Signed-off-by: Tony Lindgren <tony@atomide.com>

Any logs available ? Any throughput improvements with DMA ?

-- 
balbi
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20150317/47d68d58/attachment-0001.sig>

Re: [PATCH 3/4] ARM: dts: Add cppi41 support for dm816x MUSB

[Tony Lindgren]

* Felipe Balbi <balbi@ti.com> [150317 17:32]:
> Hi,
> 
> On Tue, Mar 17, 2015 at 05:19:20PM -0700, Tony Lindgren wrote:
> > Looks like we have cppi41 on dm816x just like on am335x.
> > 
> > Cc: Bin Liu <binmlist@gmail.com>
> > Cc: Brian Hutchinson <b.hutchman@gmail.com>
> > Cc: Felipe Balbi <balbi@ti.com>
> > Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
> > Signed-off-by: Tony Lindgren <tony@atomide.com>
> 
> Any logs available ? Any throughput improvements with DMA ?

So far I only logged with the debug option on. I can do some
test runs with your for-next branch to a USB mass storage device
if you prefer that, or got some other test in mind?

Regards,

Tony

[PATCH 3/4] ARM: dts: Add cppi41 support for dm816x MUSB

[Tony Lindgren]

* Felipe Balbi <balbi@ti.com> [150317 17:32]:
> Hi,
> 
> On Tue, Mar 17, 2015 at 05:19:20PM -0700, Tony Lindgren wrote:
> > Looks like we have cppi41 on dm816x just like on am335x.
> > 
> > Cc: Bin Liu <binmlist@gmail.com>
> > Cc: Brian Hutchinson <b.hutchman@gmail.com>
> > Cc: Felipe Balbi <balbi@ti.com>
> > Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
> > Signed-off-by: Tony Lindgren <tony@atomide.com>
> 
> Any logs available ? Any throughput improvements with DMA ?

So far I only logged with the debug option on. I can do some
test runs with your for-next branch to a USB mass storage device
if you prefer that, or got some other test in mind?

Regards,

Tony

Re: [PATCH 3/4] ARM: dts: Add cppi41 support for dm816x MUSB

[Felipe Balbi]

[-- Attachment #1: Type: text/plain, Size: 876 bytes --]

On Tue, Mar 17, 2015 at 06:18:37PM -0700, Tony Lindgren wrote:
> * Felipe Balbi <balbi@ti.com> [150317 17:32]:
> > Hi,
> > 
> > On Tue, Mar 17, 2015 at 05:19:20PM -0700, Tony Lindgren wrote:
> > > Looks like we have cppi41 on dm816x just like on am335x.
> > > 
> > > Cc: Bin Liu <binmlist@gmail.com>
> > > Cc: Brian Hutchinson <b.hutchman@gmail.com>
> > > Cc: Felipe Balbi <balbi@ti.com>
> > > Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
> > > Signed-off-by: Tony Lindgren <tony@atomide.com>
> > 
> > Any logs available ? Any throughput improvements with DMA ?
> 
> So far I only logged with the debug option on. I can do some
> test runs with your for-next branch to a USB mass storage device
> if you prefer that, or got some other test in mind?

mass storage should be fine, just wanna know if you're getting
acceptable throughput.

-- 
balbi

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]

[PATCH 3/4] ARM: dts: Add cppi41 support for dm816x MUSB

[Felipe Balbi]

On Tue, Mar 17, 2015 at 06:18:37PM -0700, Tony Lindgren wrote:
> * Felipe Balbi <balbi@ti.com> [150317 17:32]:
> > Hi,
> > 
> > On Tue, Mar 17, 2015 at 05:19:20PM -0700, Tony Lindgren wrote:
> > > Looks like we have cppi41 on dm816x just like on am335x.
> > > 
> > > Cc: Bin Liu <binmlist@gmail.com>
> > > Cc: Brian Hutchinson <b.hutchman@gmail.com>
> > > Cc: Felipe Balbi <balbi@ti.com>
> > > Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
> > > Signed-off-by: Tony Lindgren <tony@atomide.com>
> > 
> > Any logs available ? Any throughput improvements with DMA ?
> 
> So far I only logged with the debug option on. I can do some
> test runs with your for-next branch to a USB mass storage device
> if you prefer that, or got some other test in mind?

mass storage should be fine, just wanna know if you're getting
acceptable throughput.

-- 
balbi
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20150318/869be06b/attachment.sig>

Re: [PATCH 3/4] ARM: dts: Add cppi41 support for dm816x MUSB

[Tony Lindgren]

* Felipe Balbi <balbi@ti.com> [150318 07:41]:
> On Tue, Mar 17, 2015 at 06:18:37PM -0700, Tony Lindgren wrote:
> > * Felipe Balbi <balbi@ti.com> [150317 17:32]:
> > > Hi,
> > > 
> > > On Tue, Mar 17, 2015 at 05:19:20PM -0700, Tony Lindgren wrote:
> > > > Looks like we have cppi41 on dm816x just like on am335x.
> > > > 
> > > > Cc: Bin Liu <binmlist@gmail.com>
> > > > Cc: Brian Hutchinson <b.hutchman@gmail.com>
> > > > Cc: Felipe Balbi <balbi@ti.com>
> > > > Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
> > > > Signed-off-by: Tony Lindgren <tony@atomide.com>
> > > 
> > > Any logs available ? Any throughput improvements with DMA ?
> > 
> > So far I only logged with the debug option on. I can do some
> > test runs with your for-next branch to a USB mass storage device
> > if you prefer that, or got some other test in mind?
> 
> mass storage should be fine, just wanna know if you're getting
> acceptable throughput.

No luck with your current merge branch with DMA right now, it's
producing an error both on bbb and dm816x:

"musb-hdrc musb-hdrc.0.auto: Need DT for the DMA engine." 

So here are some test results against -rc4.

CONFIG_MUSB_PIO_ONLY

Copy a 10MB file to /dev/sda right after a reboot:

# time /bin/sh -c 'cp filler /mnt/ && sync'
real    0m2.480s
user    0m0.000s
sys     0m0.320s

Run hdparm a few times:

# hdparm -t /dev/sda

/dev/sda:
 Timing buffered disk reads:  34 MB in  3.16 seconds =  10.75 MB/sec


CONFIG_USB_TI_CPPI41_DMA

Copy a 10MB file to /dev/sda right after a reboot:

# time /bin/sh -c 'cp filler /mnt/ && sync'
real    0m2.095s
user    0m0.000s
sys     0m0.310s

Run hdparm a few times:

# hdparm -t /dev/sda

/dev/sda:
 Timing buffered disk reads:  52 MB in  3.07 seconds =  16.94 MB/sec

Regards,

Tony

[PATCH 3/4] ARM: dts: Add cppi41 support for dm816x MUSB

[Tony Lindgren]

* Felipe Balbi <balbi@ti.com> [150318 07:41]:
> On Tue, Mar 17, 2015 at 06:18:37PM -0700, Tony Lindgren wrote:
> > * Felipe Balbi <balbi@ti.com> [150317 17:32]:
> > > Hi,
> > > 
> > > On Tue, Mar 17, 2015 at 05:19:20PM -0700, Tony Lindgren wrote:
> > > > Looks like we have cppi41 on dm816x just like on am335x.
> > > > 
> > > > Cc: Bin Liu <binmlist@gmail.com>
> > > > Cc: Brian Hutchinson <b.hutchman@gmail.com>
> > > > Cc: Felipe Balbi <balbi@ti.com>
> > > > Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
> > > > Signed-off-by: Tony Lindgren <tony@atomide.com>
> > > 
> > > Any logs available ? Any throughput improvements with DMA ?
> > 
> > So far I only logged with the debug option on. I can do some
> > test runs with your for-next branch to a USB mass storage device
> > if you prefer that, or got some other test in mind?
> 
> mass storage should be fine, just wanna know if you're getting
> acceptable throughput.

No luck with your current merge branch with DMA right now, it's
producing an error both on bbb and dm816x:

"musb-hdrc musb-hdrc.0.auto: Need DT for the DMA engine." 

So here are some test results against -rc4.

CONFIG_MUSB_PIO_ONLY

Copy a 10MB file to /dev/sda right after a reboot:

# time /bin/sh -c 'cp filler /mnt/ && sync'
real    0m2.480s
user    0m0.000s
sys     0m0.320s

Run hdparm a few times:

# hdparm -t /dev/sda

/dev/sda:
 Timing buffered disk reads:  34 MB in  3.16 seconds =  10.75 MB/sec


CONFIG_USB_TI_CPPI41_DMA

Copy a 10MB file to /dev/sda right after a reboot:

# time /bin/sh -c 'cp filler /mnt/ && sync'
real    0m2.095s
user    0m0.000s
sys     0m0.310s

Run hdparm a few times:

# hdparm -t /dev/sda

/dev/sda:
 Timing buffered disk reads:  52 MB in  3.07 seconds =  16.94 MB/sec

Regards,

Tony

[PATCH 4/4] ARM: dts: Remove PIN_INPUT for dm816x McSPI

[Tony Lindgren]

On dm816x we have no PIN_INPUT vs PIN_OUTPUT configuration, there
are just pulls. Let's remove the bogus flags.

Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/boot/dts/dm8168-evm.dts | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/dm8168-evm.dts b/arch/arm/boot/dts/dm8168-evm.dts
index b520a8b..169a855 100644
--- a/arch/arm/boot/dts/dm8168-evm.dts
+++ b/arch/arm/boot/dts/dm8168-evm.dts
@@ -29,10 +29,10 @@
 &dm816x_pinmux {
 	mcspi1_pins: pinmux_mcspi1_pins {
 		pinctrl-single,pins = <
-			DM816X_IOPAD(0x0a94, PIN_INPUT | MUX_MODE0)	/* SPI_SCLK */
-			DM816X_IOPAD(0x0a98, PIN_OUTPUT | MUX_MODE0)	/* SPI_SCS0 */
-			DM816X_IOPAD(0x0aa8, PIN_INPUT | MUX_MODE0)	/* SPI_D0 */
-			DM816X_IOPAD(0x0aac, PIN_INPUT | MUX_MODE0)	/* SPI_D1 */
+			DM816X_IOPAD(0x0a94, MUX_MODE0)			/* SPI_SCLK */
+			DM816X_IOPAD(0x0a98, MUX_MODE0)			/* SPI_SCS0 */
+			DM816X_IOPAD(0x0aa8, MUX_MODE0)			/* SPI_D0 */
+			DM816X_IOPAD(0x0aac, MUX_MODE0)			/* SPI_D1 */
 		>;
 	};
 
-- 
2.1.4

[PATCH 4/4] ARM: dts: Remove PIN_INPUT for dm816x McSPI

[Tony Lindgren]

On dm816x we have no PIN_INPUT vs PIN_OUTPUT configuration, there
are just pulls. Let's remove the bogus flags.

Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/boot/dts/dm8168-evm.dts | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/dm8168-evm.dts b/arch/arm/boot/dts/dm8168-evm.dts
index b520a8b..169a855 100644
--- a/arch/arm/boot/dts/dm8168-evm.dts
+++ b/arch/arm/boot/dts/dm8168-evm.dts
@@ -29,10 +29,10 @@
 &dm816x_pinmux {
 	mcspi1_pins: pinmux_mcspi1_pins {
 		pinctrl-single,pins = <
-			DM816X_IOPAD(0x0a94, PIN_INPUT | MUX_MODE0)	/* SPI_SCLK */
-			DM816X_IOPAD(0x0a98, PIN_OUTPUT | MUX_MODE0)	/* SPI_SCS0 */
-			DM816X_IOPAD(0x0aa8, PIN_INPUT | MUX_MODE0)	/* SPI_D0 */
-			DM816X_IOPAD(0x0aac, PIN_INPUT | MUX_MODE0)	/* SPI_D1 */
+			DM816X_IOPAD(0x0a94, MUX_MODE0)			/* SPI_SCLK */
+			DM816X_IOPAD(0x0a98, MUX_MODE0)			/* SPI_SCS0 */
+			DM816X_IOPAD(0x0aa8, MUX_MODE0)			/* SPI_D0 */
+			DM816X_IOPAD(0x0aac, MUX_MODE0)			/* SPI_D1 */
 		>;
 	};
 
-- 
2.1.4