From: Charles Keepax <ckeepax-yzvPICuk2AATkU/dhu1WVueM+bqZidxxQQ4Iyu8u01E@public.gmane.org>
To: Inha Song <ideal.song-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
Cc: lee.jones-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org,
devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
alsa-devel-K7yf7f+aM1XWsZ/bQMPhNw@public.gmane.org,
linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
patches-yzvPICuk2AATkU/dhu1WVueM+bqZidxxQQ4Iyu8u01E@public.gmane.org,
cw00.choi-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org,
broonie-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org,
rf-yzvPICuk2AATkU/dhu1WVueM+bqZidxxQQ4Iyu8u01E@public.gmane.org,
robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org,
pawel.moll-5wv7dgnIgG8@public.gmane.org,
mark.rutland-5wv7dgnIgG8@public.gmane.org,
ijc+devicetree-KcIKpvwj1kUDXYZnReoRVg@public.gmane.org
Subject: Re: [alsa-devel] [PATCH 1/2] extcon: arizona: Add support for select accessory detect mode when headphone detection"
Date: Fri, 17 Apr 2015 10:00:47 +0100 [thread overview]
Message-ID: <20150417090047.GC3480@opensource.wolfsonmicro.com> (raw)
In-Reply-To: <1429259579-16563-2-git-send-email-ideal.song-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
On Fri, Apr 17, 2015 at 05:32:58PM +0900, Inha Song wrote:
> This patch add support for select accessory detect mode to HPDETL or HPDETR.
> Arizona provides a headphone detection circuit on the HPDETL and HPDETR pins
> to measure the impedance of an external load connected to the headphone.
>
> Depending on board design, headphone detect pins can change to HPDETR or HPDETL.
>
> Signed-off-by: Inha Song <ideal.song-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
> ---
> drivers/extcon/extcon-arizona.c | 34 ++++++++++++++++++++++++++++++----
> include/linux/mfd/arizona/pdata.h | 3 +++
> 2 files changed, 33 insertions(+), 4 deletions(-)
>
> diff --git a/drivers/extcon/extcon-arizona.c b/drivers/extcon/extcon-arizona.c
> index 63f01c4..7bc9159 100644
> --- a/drivers/extcon/extcon-arizona.c
> +++ b/drivers/extcon/extcon-arizona.c
> @@ -95,6 +95,7 @@ struct arizona_extcon_info {
> int jack_flips;
>
> int hpdet_ip;
> + int hpdet_channel;
Don't really think this is necessary we can just use the pdata
value where required doesn't add much copying it to extcon_info.
>
> struct extcon_dev *edev;
> };
> @@ -653,9 +654,9 @@ static void arizona_identify_headphone(struct arizona_extcon_info *info)
> ret = regmap_update_bits(arizona->regmap,
> ARIZONA_ACCESSORY_DETECT_MODE_1,
> ARIZONA_ACCDET_MODE_MASK,
> - ARIZONA_ACCDET_MODE_HPL);
> + info->hpdet_channel);
> if (ret != 0) {
> - dev_err(arizona->dev, "Failed to set HPDETL mode: %d\n", ret);
> + dev_err(arizona->dev, "Failed to set HPDET mode: %d\n", ret);
> goto err;
> }
>
> @@ -705,9 +706,9 @@ static void arizona_start_hpdet_acc_id(struct arizona_extcon_info *info)
> ARIZONA_ACCESSORY_DETECT_MODE_1,
> ARIZONA_ACCDET_SRC | ARIZONA_ACCDET_MODE_MASK,
> info->micd_modes[0].src |
> - ARIZONA_ACCDET_MODE_HPL);
> + info->hpdet_channel);
> if (ret != 0) {
> - dev_err(arizona->dev, "Failed to set HPDETL mode: %d\n", ret);
> + dev_err(arizona->dev, "Failed to set HPDET mode: %d\n", ret);
> goto err;
> }
>
> @@ -1103,6 +1104,23 @@ static void arizona_micd_set_level(struct arizona *arizona, int index,
> regmap_update_bits(arizona->regmap, reg, mask, level);
> }
>
> +#ifdef CONFIG_OF
> +static int arizona_of_get_extcon_pdata(struct arizona *arizona)
> +{
> + struct arizona_pdata *pdata = &arizona->pdata;
> +
> + of_property_read_u32(arizona->dev->of_node, "wlf,hpdet-channel",
> + &pdata->hpdet_channel);
> +
> + return 0;
> +}
> +#else
> +static inline int arizona_of_get_extcon_pdata(struct arizona *arizona)
> +{
> + return 0;
> +}
> +#endif
> +
I believe it is preferred to leave this as not ifdef'ed...
> static int arizona_extcon_probe(struct platform_device *pdev)
> {
> struct arizona *arizona = dev_get_drvdata(pdev->dev.parent);
> @@ -1120,6 +1138,9 @@ static int arizona_extcon_probe(struct platform_device *pdev)
> if (!info)
> return -ENOMEM;
>
> + if (!dev_get_platdata(arizona->dev))
> + arizona_of_get_extcon_pdata(arizona);
And to wrap this in an if (IS_ENABLED(CONFIG_OF)).
> +
> info->micvdd = devm_regulator_get(&pdev->dev, "MICVDD");
> if (IS_ERR(info->micvdd)) {
> ret = PTR_ERR(info->micvdd);
> @@ -1338,6 +1359,11 @@ static int arizona_extcon_probe(struct platform_device *pdev)
>
> arizona_extcon_set_mode(info, 0);
>
> + if (arizona->pdata.hpdet_channel)
> + info->hpdet_channel = ARIZONA_ACCDET_MODE_HPR;
> + else
> + info->hpdet_channel = ARIZONA_ACCDET_MODE_HPL;
> +
Just move the two defines in include/dt-bindings/mfd/arizona.h
and have the pdata get set directly to one of the values.
> pm_runtime_enable(&pdev->dev);
> pm_runtime_idle(&pdev->dev);
> pm_runtime_get_sync(&pdev->dev);
> diff --git a/include/linux/mfd/arizona/pdata.h b/include/linux/mfd/arizona/pdata.h
> index 4578c72..feb5903 100644
> --- a/include/linux/mfd/arizona/pdata.h
> +++ b/include/linux/mfd/arizona/pdata.h
> @@ -139,6 +139,9 @@ struct arizona_pdata {
> /** GPIO used for mic isolation with HPDET */
> int hpdet_id_gpio;
>
> + /** Channel to use for headphone detection */
> + int hpdet_channel;
Lets use and unsigned here, we don't need it to be signed and it
saves type issues with read_u32.
> +
> /** Extra debounce timeout used during initial mic detection (ms) */
> int micd_detect_debounce;
>
> --
> 2.0.0.390.gcb682f8
>
Thanks,
Charles
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
WARNING: multiple messages have this Message-ID (diff)
From: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
To: Inha Song <ideal.song@samsung.com>
Cc: lee.jones@linaro.org, devicetree@vger.kernel.org,
alsa-devel@alsa-project.org, linux-kernel@vger.kernel.org,
patches@opensource.wolfsonmicro.com, cw00.choi@samsung.com,
broonie@kernel.org, rf@opensource.wolfsonmicro.com,
robh+dt@kernel.org, pawel.moll@arm.com, mark.rutland@arm.com,
ijc+devicetree@hellion.org.uk
Subject: Re: [alsa-devel] [PATCH 1/2] extcon: arizona: Add support for select accessory detect mode when headphone detection"
Date: Fri, 17 Apr 2015 10:00:47 +0100 [thread overview]
Message-ID: <20150417090047.GC3480@opensource.wolfsonmicro.com> (raw)
In-Reply-To: <1429259579-16563-2-git-send-email-ideal.song@samsung.com>
On Fri, Apr 17, 2015 at 05:32:58PM +0900, Inha Song wrote:
> This patch add support for select accessory detect mode to HPDETL or HPDETR.
> Arizona provides a headphone detection circuit on the HPDETL and HPDETR pins
> to measure the impedance of an external load connected to the headphone.
>
> Depending on board design, headphone detect pins can change to HPDETR or HPDETL.
>
> Signed-off-by: Inha Song <ideal.song@samsung.com>
> ---
> drivers/extcon/extcon-arizona.c | 34 ++++++++++++++++++++++++++++++----
> include/linux/mfd/arizona/pdata.h | 3 +++
> 2 files changed, 33 insertions(+), 4 deletions(-)
>
> diff --git a/drivers/extcon/extcon-arizona.c b/drivers/extcon/extcon-arizona.c
> index 63f01c4..7bc9159 100644
> --- a/drivers/extcon/extcon-arizona.c
> +++ b/drivers/extcon/extcon-arizona.c
> @@ -95,6 +95,7 @@ struct arizona_extcon_info {
> int jack_flips;
>
> int hpdet_ip;
> + int hpdet_channel;
Don't really think this is necessary we can just use the pdata
value where required doesn't add much copying it to extcon_info.
>
> struct extcon_dev *edev;
> };
> @@ -653,9 +654,9 @@ static void arizona_identify_headphone(struct arizona_extcon_info *info)
> ret = regmap_update_bits(arizona->regmap,
> ARIZONA_ACCESSORY_DETECT_MODE_1,
> ARIZONA_ACCDET_MODE_MASK,
> - ARIZONA_ACCDET_MODE_HPL);
> + info->hpdet_channel);
> if (ret != 0) {
> - dev_err(arizona->dev, "Failed to set HPDETL mode: %d\n", ret);
> + dev_err(arizona->dev, "Failed to set HPDET mode: %d\n", ret);
> goto err;
> }
>
> @@ -705,9 +706,9 @@ static void arizona_start_hpdet_acc_id(struct arizona_extcon_info *info)
> ARIZONA_ACCESSORY_DETECT_MODE_1,
> ARIZONA_ACCDET_SRC | ARIZONA_ACCDET_MODE_MASK,
> info->micd_modes[0].src |
> - ARIZONA_ACCDET_MODE_HPL);
> + info->hpdet_channel);
> if (ret != 0) {
> - dev_err(arizona->dev, "Failed to set HPDETL mode: %d\n", ret);
> + dev_err(arizona->dev, "Failed to set HPDET mode: %d\n", ret);
> goto err;
> }
>
> @@ -1103,6 +1104,23 @@ static void arizona_micd_set_level(struct arizona *arizona, int index,
> regmap_update_bits(arizona->regmap, reg, mask, level);
> }
>
> +#ifdef CONFIG_OF
> +static int arizona_of_get_extcon_pdata(struct arizona *arizona)
> +{
> + struct arizona_pdata *pdata = &arizona->pdata;
> +
> + of_property_read_u32(arizona->dev->of_node, "wlf,hpdet-channel",
> + &pdata->hpdet_channel);
> +
> + return 0;
> +}
> +#else
> +static inline int arizona_of_get_extcon_pdata(struct arizona *arizona)
> +{
> + return 0;
> +}
> +#endif
> +
I believe it is preferred to leave this as not ifdef'ed...
> static int arizona_extcon_probe(struct platform_device *pdev)
> {
> struct arizona *arizona = dev_get_drvdata(pdev->dev.parent);
> @@ -1120,6 +1138,9 @@ static int arizona_extcon_probe(struct platform_device *pdev)
> if (!info)
> return -ENOMEM;
>
> + if (!dev_get_platdata(arizona->dev))
> + arizona_of_get_extcon_pdata(arizona);
And to wrap this in an if (IS_ENABLED(CONFIG_OF)).
> +
> info->micvdd = devm_regulator_get(&pdev->dev, "MICVDD");
> if (IS_ERR(info->micvdd)) {
> ret = PTR_ERR(info->micvdd);
> @@ -1338,6 +1359,11 @@ static int arizona_extcon_probe(struct platform_device *pdev)
>
> arizona_extcon_set_mode(info, 0);
>
> + if (arizona->pdata.hpdet_channel)
> + info->hpdet_channel = ARIZONA_ACCDET_MODE_HPR;
> + else
> + info->hpdet_channel = ARIZONA_ACCDET_MODE_HPL;
> +
Just move the two defines in include/dt-bindings/mfd/arizona.h
and have the pdata get set directly to one of the values.
> pm_runtime_enable(&pdev->dev);
> pm_runtime_idle(&pdev->dev);
> pm_runtime_get_sync(&pdev->dev);
> diff --git a/include/linux/mfd/arizona/pdata.h b/include/linux/mfd/arizona/pdata.h
> index 4578c72..feb5903 100644
> --- a/include/linux/mfd/arizona/pdata.h
> +++ b/include/linux/mfd/arizona/pdata.h
> @@ -139,6 +139,9 @@ struct arizona_pdata {
> /** GPIO used for mic isolation with HPDET */
> int hpdet_id_gpio;
>
> + /** Channel to use for headphone detection */
> + int hpdet_channel;
Lets use and unsigned here, we don't need it to be signed and it
saves type issues with read_u32.
> +
> /** Extra debounce timeout used during initial mic detection (ms) */
> int micd_detect_debounce;
>
> --
> 2.0.0.390.gcb682f8
>
Thanks,
Charles
next prev parent reply other threads:[~2015-04-17 9:00 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-04-17 8:32 [PATCH 0/2] Add support for select accessory detect mode to HPDETL or HPDETR Inha Song
2015-04-17 8:32 ` [alsa-devel] " Inha Song
2015-04-17 8:32 ` [alsa-devel] [PATCH 1/2] extcon: arizona: Add support for select accessory detect mode when headphone detection" Inha Song
[not found] ` <1429259579-16563-2-git-send-email-ideal.song-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
2015-04-17 9:00 ` Charles Keepax [this message]
2015-04-17 9:00 ` Charles Keepax
2015-04-20 1:45 ` Inha Song
2015-04-20 8:29 ` Charles Keepax
2015-04-20 8:29 ` Charles Keepax
2015-04-17 9:30 ` Charles Keepax
2015-04-17 9:30 ` Charles Keepax
2015-04-17 8:32 ` [alsa-devel] [PATCH 2/2] mfd: arizona: Update DT binding to support hpdet channel Inha Song
[not found] ` <1429259579-16563-3-git-send-email-ideal.song-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
2015-04-17 9:01 ` Charles Keepax
2015-04-17 9:01 ` Charles Keepax
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20150417090047.GC3480@opensource.wolfsonmicro.com \
--to=ckeepax-yzvpicuk2aatku/dhu1wvuem+bqzidxxqq4iyu8u01e@public.gmane.org \
--cc=alsa-devel-K7yf7f+aM1XWsZ/bQMPhNw@public.gmane.org \
--cc=broonie-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org \
--cc=cw00.choi-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org \
--cc=devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=ideal.song-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org \
--cc=ijc+devicetree-KcIKpvwj1kUDXYZnReoRVg@public.gmane.org \
--cc=lee.jones-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org \
--cc=linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=mark.rutland-5wv7dgnIgG8@public.gmane.org \
--cc=patches-yzvPICuk2AATkU/dhu1WVueM+bqZidxxQQ4Iyu8u01E@public.gmane.org \
--cc=pawel.moll-5wv7dgnIgG8@public.gmane.org \
--cc=rf-yzvPICuk2AATkU/dhu1WVueM+bqZidxxQQ4Iyu8u01E@public.gmane.org \
--cc=robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.