* [PATCH v3 1/2] arm64: dts: Add dts files for Marvell Berlin4CT SoC
@ 2015-07-22 8:57 ` Jisheng Zhang
0 siblings, 0 replies; 14+ messages in thread
From: Jisheng Zhang @ 2015-07-22 8:57 UTC (permalink / raw)
To: catalin.marinas, will.deacon, khilman, arnd, olof, mark.rutland,
sudeep.holla, robh+dt, galak, pawel.moll
Cc: linux-arm-kernel, linux-kernel, devicetree, Jisheng Zhang
Add initial dtsi file to support Marvell Berlin4CT SoC with
quad Cortex-A53 CPUs.
It also adds dts file for Marvell Berlin4CT DMP board which is
based on Berlin4CT SoC.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
---
arch/arm64/boot/dts/Makefile | 1 +
arch/arm64/boot/dts/marvell/Makefile | 5 +
arch/arm64/boot/dts/marvell/berlin4ct-dmp.dts | 67 +++++++++++
arch/arm64/boot/dts/marvell/berlin4ct.dtsi | 164 ++++++++++++++++++++++++++
4 files changed, 237 insertions(+)
create mode 100644 arch/arm64/boot/dts/marvell/Makefile
create mode 100644 arch/arm64/boot/dts/marvell/berlin4ct-dmp.dts
create mode 100644 arch/arm64/boot/dts/marvell/berlin4ct.dtsi
diff --git a/arch/arm64/boot/dts/Makefile b/arch/arm64/boot/dts/Makefile
index 0c57290..61e9493 100644
--- a/arch/arm64/boot/dts/Makefile
+++ b/arch/arm64/boot/dts/Makefile
@@ -5,6 +5,7 @@ dts-dirs += cavium
dts-dirs += exynos
dts-dirs += freescale
dts-dirs += hisilicon
+dts-dirs += marvell
dts-dirs += mediatek
dts-dirs += qcom
dts-dirs += rockchip
diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile
new file mode 100644
index 0000000..e2f6afa
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/Makefile
@@ -0,0 +1,5 @@
+dtb-$(CONFIG_ARCH_BERLIN) += berlin4ct-dmp.dtb
+
+always := $(dtb-y)
+subdir-y := $(dts-dirs)
+clean-files := *.dtb
diff --git a/arch/arm64/boot/dts/marvell/berlin4ct-dmp.dts b/arch/arm64/boot/dts/marvell/berlin4ct-dmp.dts
new file mode 100644
index 0000000..58ed7f1
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/berlin4ct-dmp.dts
@@ -0,0 +1,67 @@
+/*
+ * Copyright (C) 2015 Marvell Technology Group Ltd.
+ *
+ * Author: Jisheng Zhang <jszhang@marvell.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPLv2 or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "berlin4ct.dtsi"
+
+/ {
+ model = "MARVELL BG4CT DMP BOARD";
+ compatible = "marvell,berlin4ct-dmp", "marvell,berlin4ct", "marvell,berlin";
+
+ chosen {
+ bootargs = "earlycon=uart8250,mmio32,0xf7fcd000";
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory {
+ device_type = "memory";
+ /* the first 16MB is for firmwares's usage */
+ reg = <0 0x01000000 0 0x80000000>;
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/marvell/berlin4ct.dtsi b/arch/arm64/boot/dts/marvell/berlin4ct.dtsi
new file mode 100644
index 0000000..becaedc
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/berlin4ct.dtsi
@@ -0,0 +1,164 @@
+/*
+ * Copyright (C) 2015 Marvell Technology Group Ltd.
+ *
+ * Author: Jisheng Zhang <jszhang@marvell.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPLv2 or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+ compatible = "marvell,berlin";
+ interrupt-parent = <&gic>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ psci {
+ compatible = "arm,psci-0.2";
+ method = "smc";
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: cpu@0 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <0x0>;
+ enable-method = "psci";
+ };
+
+ cpu1: cpu@1 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <0x1>;
+ enable-method = "psci";
+ };
+
+ cpu2: cpu@2 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <0x2>;
+ enable-method = "psci";
+ };
+
+ cpu3: cpu@3 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <0x3>;
+ enable-method = "psci";
+ };
+ };
+
+ pmu {
+ compatible = "arm,armv8-pmuv3";
+ interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-affinity = <&cpu0>,
+ <&cpu1>,
+ <&cpu2>,
+ <&cpu3>;
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+ };
+
+ soc {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0 0xf7000000 0x1000000>;
+
+ osc: osc {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <25000000>;
+ };
+
+ gic: interrupt-controller@901000 {
+ compatible = "arm,gic-400";
+ #interrupt-cells = <3>;
+ interrupt-controller;
+ reg = <0x901000 0x1000>,
+ <0x902000 0x2000>,
+ <0x904000 0x2000>,
+ <0x906000 0x2000>;
+ interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+ };
+
+ apb@fc0000 {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0xfc0000 0x10000>;
+ interrupt-parent = <&sic>;
+
+ sic: interrupt-controller@1000 {
+ compatible = "snps,dw-apb-ictl";
+ reg = <0x1000 0x30>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ interrupt-parent = <&gic>;
+ interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ uart0: uart@d000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0xd000 0x100>;
+ interrupts = <8>;
+ clocks = <&osc>;
+ reg-shift = <2>;
+ status = "disabled";
+ };
+ };
+ };
+};
--
2.1.4
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH v3 1/2] arm64: dts: Add dts files for Marvell Berlin4CT SoC
@ 2015-07-22 8:57 ` Jisheng Zhang
0 siblings, 0 replies; 14+ messages in thread
From: Jisheng Zhang @ 2015-07-22 8:57 UTC (permalink / raw)
To: catalin.marinas, will.deacon, khilman, arnd, olof, mark.rutland,
sudeep.holla, robh+dt, galak, pawel.moll
Cc: linux-arm-kernel, linux-kernel, devicetree, Jisheng Zhang
Add initial dtsi file to support Marvell Berlin4CT SoC with
quad Cortex-A53 CPUs.
It also adds dts file for Marvell Berlin4CT DMP board which is
based on Berlin4CT SoC.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
---
arch/arm64/boot/dts/Makefile | 1 +
arch/arm64/boot/dts/marvell/Makefile | 5 +
arch/arm64/boot/dts/marvell/berlin4ct-dmp.dts | 67 +++++++++++
arch/arm64/boot/dts/marvell/berlin4ct.dtsi | 164 ++++++++++++++++++++++++++
4 files changed, 237 insertions(+)
create mode 100644 arch/arm64/boot/dts/marvell/Makefile
create mode 100644 arch/arm64/boot/dts/marvell/berlin4ct-dmp.dts
create mode 100644 arch/arm64/boot/dts/marvell/berlin4ct.dtsi
diff --git a/arch/arm64/boot/dts/Makefile b/arch/arm64/boot/dts/Makefile
index 0c57290..61e9493 100644
--- a/arch/arm64/boot/dts/Makefile
+++ b/arch/arm64/boot/dts/Makefile
@@ -5,6 +5,7 @@ dts-dirs += cavium
dts-dirs += exynos
dts-dirs += freescale
dts-dirs += hisilicon
+dts-dirs += marvell
dts-dirs += mediatek
dts-dirs += qcom
dts-dirs += rockchip
diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile
new file mode 100644
index 0000000..e2f6afa
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/Makefile
@@ -0,0 +1,5 @@
+dtb-$(CONFIG_ARCH_BERLIN) += berlin4ct-dmp.dtb
+
+always := $(dtb-y)
+subdir-y := $(dts-dirs)
+clean-files := *.dtb
diff --git a/arch/arm64/boot/dts/marvell/berlin4ct-dmp.dts b/arch/arm64/boot/dts/marvell/berlin4ct-dmp.dts
new file mode 100644
index 0000000..58ed7f1
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/berlin4ct-dmp.dts
@@ -0,0 +1,67 @@
+/*
+ * Copyright (C) 2015 Marvell Technology Group Ltd.
+ *
+ * Author: Jisheng Zhang <jszhang@marvell.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPLv2 or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "berlin4ct.dtsi"
+
+/ {
+ model = "MARVELL BG4CT DMP BOARD";
+ compatible = "marvell,berlin4ct-dmp", "marvell,berlin4ct", "marvell,berlin";
+
+ chosen {
+ bootargs = "earlycon=uart8250,mmio32,0xf7fcd000";
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory {
+ device_type = "memory";
+ /* the first 16MB is for firmwares's usage */
+ reg = <0 0x01000000 0 0x80000000>;
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/marvell/berlin4ct.dtsi b/arch/arm64/boot/dts/marvell/berlin4ct.dtsi
new file mode 100644
index 0000000..becaedc
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/berlin4ct.dtsi
@@ -0,0 +1,164 @@
+/*
+ * Copyright (C) 2015 Marvell Technology Group Ltd.
+ *
+ * Author: Jisheng Zhang <jszhang@marvell.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPLv2 or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+ compatible = "marvell,berlin";
+ interrupt-parent = <&gic>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ psci {
+ compatible = "arm,psci-0.2";
+ method = "smc";
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: cpu@0 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <0x0>;
+ enable-method = "psci";
+ };
+
+ cpu1: cpu@1 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <0x1>;
+ enable-method = "psci";
+ };
+
+ cpu2: cpu@2 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <0x2>;
+ enable-method = "psci";
+ };
+
+ cpu3: cpu@3 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <0x3>;
+ enable-method = "psci";
+ };
+ };
+
+ pmu {
+ compatible = "arm,armv8-pmuv3";
+ interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-affinity = <&cpu0>,
+ <&cpu1>,
+ <&cpu2>,
+ <&cpu3>;
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+ };
+
+ soc {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0 0xf7000000 0x1000000>;
+
+ osc: osc {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <25000000>;
+ };
+
+ gic: interrupt-controller@901000 {
+ compatible = "arm,gic-400";
+ #interrupt-cells = <3>;
+ interrupt-controller;
+ reg = <0x901000 0x1000>,
+ <0x902000 0x2000>,
+ <0x904000 0x2000>,
+ <0x906000 0x2000>;
+ interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+ };
+
+ apb@fc0000 {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0xfc0000 0x10000>;
+ interrupt-parent = <&sic>;
+
+ sic: interrupt-controller@1000 {
+ compatible = "snps,dw-apb-ictl";
+ reg = <0x1000 0x30>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ interrupt-parent = <&gic>;
+ interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ uart0: uart@d000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0xd000 0x100>;
+ interrupts = <8>;
+ clocks = <&osc>;
+ reg-shift = <2>;
+ status = "disabled";
+ };
+ };
+ };
+};
--
2.1.4
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH v3 1/2] arm64: dts: Add dts files for Marvell Berlin4CT SoC
@ 2015-07-22 9:19 ` Sudeep Holla
0 siblings, 0 replies; 14+ messages in thread
From: Sudeep Holla @ 2015-07-22 9:19 UTC (permalink / raw)
To: linux-arm-kernel
On 22/07/15 09:57, Jisheng Zhang wrote:
> Add initial dtsi file to support Marvell Berlin4CT SoC with
> quad Cortex-A53 CPUs.
>
> It also adds dts file for Marvell Berlin4CT DMP board which is
> based on Berlin4CT SoC.
>
> Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
> ---
> arch/arm64/boot/dts/Makefile | 1 +
> arch/arm64/boot/dts/marvell/Makefile | 5 +
> arch/arm64/boot/dts/marvell/berlin4ct-dmp.dts | 67 +++++++++++
> arch/arm64/boot/dts/marvell/berlin4ct.dtsi | 164 ++++++++++++++++++++++++++
> 4 files changed, 237 insertions(+)
> create mode 100644 arch/arm64/boot/dts/marvell/Makefile
> create mode 100644 arch/arm64/boot/dts/marvell/berlin4ct-dmp.dts
> create mode 100644 arch/arm64/boot/dts/marvell/berlin4ct.dtsi
>
[..]
> diff --git a/arch/arm64/boot/dts/marvell/berlin4ct-dmp.dts b/arch/arm64/boot/dts/marvell/berlin4ct-dmp.dts
> new file mode 100644
> index 0000000..58ed7f1
> --- /dev/null
> +++ b/arch/arm64/boot/dts/marvell/berlin4ct-dmp.dts
> @@ -0,0 +1,67 @@
[..]
> +/dts-v1/;
> +
> +#include "berlin4ct.dtsi"
> +
> +/ {
> + model = "MARVELL BG4CT DMP BOARD";
> + compatible = "marvell,berlin4ct-dmp", "marvell,berlin4ct", "marvell,berlin";
> +
> + chosen {
> + bootargs = "earlycon=uart8250,mmio32,0xf7fcd000";
> + stdout-path = "serial0:115200n8";
Just earlycon without any parameters will suffice. Currently earlycon
parsing code has issues and it's being worked out[1]. The serial port
details specified in stdout-path will be used by earlycon.
Regards,
Sudeep
[1] https://lkml.org/lkml/2015/4/8/604
^ permalink raw reply [flat|nested] 14+ messages in thread* Re: [PATCH v3 1/2] arm64: dts: Add dts files for Marvell Berlin4CT SoC
@ 2015-07-22 9:19 ` Sudeep Holla
0 siblings, 0 replies; 14+ messages in thread
From: Sudeep Holla @ 2015-07-22 9:19 UTC (permalink / raw)
To: Jisheng Zhang, Catalin Marinas, Will Deacon, khilman@linaro.org,
arnd@arndb.de, olof@lixom.net, Mark Rutland, robh+dt@kernel.org,
galak@codeaurora.org, Pawel Moll
Cc: Sudeep Holla, linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org, devicetree@vger.kernel.org
On 22/07/15 09:57, Jisheng Zhang wrote:
> Add initial dtsi file to support Marvell Berlin4CT SoC with
> quad Cortex-A53 CPUs.
>
> It also adds dts file for Marvell Berlin4CT DMP board which is
> based on Berlin4CT SoC.
>
> Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
> ---
> arch/arm64/boot/dts/Makefile | 1 +
> arch/arm64/boot/dts/marvell/Makefile | 5 +
> arch/arm64/boot/dts/marvell/berlin4ct-dmp.dts | 67 +++++++++++
> arch/arm64/boot/dts/marvell/berlin4ct.dtsi | 164 ++++++++++++++++++++++++++
> 4 files changed, 237 insertions(+)
> create mode 100644 arch/arm64/boot/dts/marvell/Makefile
> create mode 100644 arch/arm64/boot/dts/marvell/berlin4ct-dmp.dts
> create mode 100644 arch/arm64/boot/dts/marvell/berlin4ct.dtsi
>
[..]
> diff --git a/arch/arm64/boot/dts/marvell/berlin4ct-dmp.dts b/arch/arm64/boot/dts/marvell/berlin4ct-dmp.dts
> new file mode 100644
> index 0000000..58ed7f1
> --- /dev/null
> +++ b/arch/arm64/boot/dts/marvell/berlin4ct-dmp.dts
> @@ -0,0 +1,67 @@
[..]
> +/dts-v1/;
> +
> +#include "berlin4ct.dtsi"
> +
> +/ {
> + model = "MARVELL BG4CT DMP BOARD";
> + compatible = "marvell,berlin4ct-dmp", "marvell,berlin4ct", "marvell,berlin";
> +
> + chosen {
> + bootargs = "earlycon=uart8250,mmio32,0xf7fcd000";
> + stdout-path = "serial0:115200n8";
Just earlycon without any parameters will suffice. Currently earlycon
parsing code has issues and it's being worked out[1]. The serial port
details specified in stdout-path will be used by earlycon.
Regards,
Sudeep
[1] https://lkml.org/lkml/2015/4/8/604
^ permalink raw reply [flat|nested] 14+ messages in thread* Re: [PATCH v3 1/2] arm64: dts: Add dts files for Marvell Berlin4CT SoC
@ 2015-07-22 9:19 ` Sudeep Holla
0 siblings, 0 replies; 14+ messages in thread
From: Sudeep Holla @ 2015-07-22 9:19 UTC (permalink / raw)
To: Jisheng Zhang, Catalin Marinas, Will Deacon,
khilman-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org,
arnd-r2nGTMty4D4@public.gmane.org,
olof-nZhT3qVonbNeoWH0uzbU5w@public.gmane.org, Mark Rutland,
robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org,
galak-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org, Pawel Moll
Cc: Sudeep Holla,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org,
linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
On 22/07/15 09:57, Jisheng Zhang wrote:
> Add initial dtsi file to support Marvell Berlin4CT SoC with
> quad Cortex-A53 CPUs.
>
> It also adds dts file for Marvell Berlin4CT DMP board which is
> based on Berlin4CT SoC.
>
> Signed-off-by: Jisheng Zhang <jszhang-eYqpPyKDWXRBDgjK7y7TUQ@public.gmane.org>
> ---
> arch/arm64/boot/dts/Makefile | 1 +
> arch/arm64/boot/dts/marvell/Makefile | 5 +
> arch/arm64/boot/dts/marvell/berlin4ct-dmp.dts | 67 +++++++++++
> arch/arm64/boot/dts/marvell/berlin4ct.dtsi | 164 ++++++++++++++++++++++++++
> 4 files changed, 237 insertions(+)
> create mode 100644 arch/arm64/boot/dts/marvell/Makefile
> create mode 100644 arch/arm64/boot/dts/marvell/berlin4ct-dmp.dts
> create mode 100644 arch/arm64/boot/dts/marvell/berlin4ct.dtsi
>
[..]
> diff --git a/arch/arm64/boot/dts/marvell/berlin4ct-dmp.dts b/arch/arm64/boot/dts/marvell/berlin4ct-dmp.dts
> new file mode 100644
> index 0000000..58ed7f1
> --- /dev/null
> +++ b/arch/arm64/boot/dts/marvell/berlin4ct-dmp.dts
> @@ -0,0 +1,67 @@
[..]
> +/dts-v1/;
> +
> +#include "berlin4ct.dtsi"
> +
> +/ {
> + model = "MARVELL BG4CT DMP BOARD";
> + compatible = "marvell,berlin4ct-dmp", "marvell,berlin4ct", "marvell,berlin";
> +
> + chosen {
> + bootargs = "earlycon=uart8250,mmio32,0xf7fcd000";
> + stdout-path = "serial0:115200n8";
Just earlycon without any parameters will suffice. Currently earlycon
parsing code has issues and it's being worked out[1]. The serial port
details specified in stdout-path will be used by earlycon.
Regards,
Sudeep
[1] https://lkml.org/lkml/2015/4/8/604
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 14+ messages in thread* [PATCH v3 1/2] arm64: dts: Add dts files for Marvell Berlin4CT SoC
2015-07-22 9:19 ` Sudeep Holla
@ 2015-07-22 9:35 ` Jisheng Zhang
-1 siblings, 0 replies; 14+ messages in thread
From: Jisheng Zhang @ 2015-07-22 9:35 UTC (permalink / raw)
To: linux-arm-kernel
Dear Sudeep,
On Wed, 22 Jul 2015 10:19:19 +0100
Sudeep Holla <sudeep.holla@arm.com> wrote:
>
>
> On 22/07/15 09:57, Jisheng Zhang wrote:
> > Add initial dtsi file to support Marvell Berlin4CT SoC with
> > quad Cortex-A53 CPUs.
> >
> > It also adds dts file for Marvell Berlin4CT DMP board which is
> > based on Berlin4CT SoC.
> >
> > Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
> > ---
> > arch/arm64/boot/dts/Makefile | 1 +
> > arch/arm64/boot/dts/marvell/Makefile | 5 +
> > arch/arm64/boot/dts/marvell/berlin4ct-dmp.dts | 67 +++++++++++
> > arch/arm64/boot/dts/marvell/berlin4ct.dtsi | 164 ++++++++++++++++++++++++++
> > 4 files changed, 237 insertions(+)
> > create mode 100644 arch/arm64/boot/dts/marvell/Makefile
> > create mode 100644 arch/arm64/boot/dts/marvell/berlin4ct-dmp.dts
> > create mode 100644 arch/arm64/boot/dts/marvell/berlin4ct.dtsi
> >
>
> [..]
>
> > diff --git a/arch/arm64/boot/dts/marvell/berlin4ct-dmp.dts b/arch/arm64/boot/dts/marvell/berlin4ct-dmp.dts
> > new file mode 100644
> > index 0000000..58ed7f1
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/marvell/berlin4ct-dmp.dts
> > @@ -0,0 +1,67 @@
>
> [..]
>
> > +/dts-v1/;
> > +
> > +#include "berlin4ct.dtsi"
> > +
> > +/ {
> > + model = "MARVELL BG4CT DMP BOARD";
> > + compatible = "marvell,berlin4ct-dmp", "marvell,berlin4ct", "marvell,berlin";
> > +
> > + chosen {
> > + bootargs = "earlycon=uart8250,mmio32,0xf7fcd000";
> > + stdout-path = "serial0:115200n8";
>
> Just earlycon without any parameters will suffice. Currently earlycon
> parsing code has issues and it's being worked out[1]. The serial port
> details specified in stdout-path will be used by earlycon.
>
> Regards,
> Sudeep
>
> [1] https://lkml.org/lkml/2015/4/8/604
I just found all arm64 ports don't have bootargs, so neither earlycon, I will
follow this behavior. Will send out v4 later.
Thanks
^ permalink raw reply [flat|nested] 14+ messages in thread* Re: [PATCH v3 1/2] arm64: dts: Add dts files for Marvell Berlin4CT SoC
@ 2015-07-22 9:35 ` Jisheng Zhang
0 siblings, 0 replies; 14+ messages in thread
From: Jisheng Zhang @ 2015-07-22 9:35 UTC (permalink / raw)
To: Sudeep Holla
Cc: Catalin Marinas, Will Deacon, khilman@linaro.org, arnd@arndb.de,
olof@lixom.net, Mark Rutland, robh+dt@kernel.org,
galak@codeaurora.org, Pawel Moll,
linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org, devicetree@vger.kernel.org
Dear Sudeep,
On Wed, 22 Jul 2015 10:19:19 +0100
Sudeep Holla <sudeep.holla@arm.com> wrote:
>
>
> On 22/07/15 09:57, Jisheng Zhang wrote:
> > Add initial dtsi file to support Marvell Berlin4CT SoC with
> > quad Cortex-A53 CPUs.
> >
> > It also adds dts file for Marvell Berlin4CT DMP board which is
> > based on Berlin4CT SoC.
> >
> > Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
> > ---
> > arch/arm64/boot/dts/Makefile | 1 +
> > arch/arm64/boot/dts/marvell/Makefile | 5 +
> > arch/arm64/boot/dts/marvell/berlin4ct-dmp.dts | 67 +++++++++++
> > arch/arm64/boot/dts/marvell/berlin4ct.dtsi | 164 ++++++++++++++++++++++++++
> > 4 files changed, 237 insertions(+)
> > create mode 100644 arch/arm64/boot/dts/marvell/Makefile
> > create mode 100644 arch/arm64/boot/dts/marvell/berlin4ct-dmp.dts
> > create mode 100644 arch/arm64/boot/dts/marvell/berlin4ct.dtsi
> >
>
> [..]
>
> > diff --git a/arch/arm64/boot/dts/marvell/berlin4ct-dmp.dts b/arch/arm64/boot/dts/marvell/berlin4ct-dmp.dts
> > new file mode 100644
> > index 0000000..58ed7f1
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/marvell/berlin4ct-dmp.dts
> > @@ -0,0 +1,67 @@
>
> [..]
>
> > +/dts-v1/;
> > +
> > +#include "berlin4ct.dtsi"
> > +
> > +/ {
> > + model = "MARVELL BG4CT DMP BOARD";
> > + compatible = "marvell,berlin4ct-dmp", "marvell,berlin4ct", "marvell,berlin";
> > +
> > + chosen {
> > + bootargs = "earlycon=uart8250,mmio32,0xf7fcd000";
> > + stdout-path = "serial0:115200n8";
>
> Just earlycon without any parameters will suffice. Currently earlycon
> parsing code has issues and it's being worked out[1]. The serial port
> details specified in stdout-path will be used by earlycon.
>
> Regards,
> Sudeep
>
> [1] https://lkml.org/lkml/2015/4/8/604
I just found all arm64 ports don't have bootargs, so neither earlycon, I will
follow this behavior. Will send out v4 later.
Thanks
^ permalink raw reply [flat|nested] 14+ messages in thread