Re: [PATCH 08/11] MTD: m25p80: Add option to limit SPI transfer size.

[Marek Vasut <marex@denx.de>]

On Monday, July 27, 2015 at 10:43:05 PM, Michal Suchanek wrote:
> On 27 July 2015 at 19:43, Marek Vasut <marex@denx.de> wrote:
> > On Monday, July 27, 2015 at 11:46:25 AM, Michal Suchanek wrote:
> >> On 24 July 2015 at 10:34, Marek Vasut <marex@denx.de> wrote:
> >> > On Thursday, July 23, 2015 at 07:03:47 PM, Michal Suchanek wrote:
> >> Ok, so here is some summary.
> >> 
> >> I have a NOR flash attached to a s3c64xx SPI controller with 64byte
> >> fifo and a pl330 dma controller.
> >> 
> >> Normally DMA controller is used for transfers that do not fit into the
> >> FIFO.
> >> 
> >> I tried adding the flash memory ID to the spi-nor driver table and
> >> adding a DT node for it.
> >> 
> >> The flash is rated at 120MHz so I used that speed but the ID was
> >> bit-shifted and identification failed. There is DT property
> >> samsung,spi-feedback-delay for addressing this and at 120MHz it must
> >> be 2 or 3 on this board. 40MHz works with default value 0.
> >> 
> >> The next step after identification worked was to try reading the flash
> >> content. For this the DMA controller is used because data is
> >> transferred in blocks larger than 64 bytes. When reading the whole 4MB
> >> flash the transfer failed silently. I got a 4MB file of all ones or
> >> all zeroes.
> >> 
> >> It turns out that
> >> 
> >>  - the pl330 locks up when transfering large amount of data.
> >> 
> >> Specifically, the maximum power of 2 sized transfer at 120MHz is 128
> >> bytes and 64k at 40MHz. Transferring more than this results in the
> >> pl330 locking up and never signalling completion of the transfer.
> > 
> > Hypothesis:
> > I think this might just be that the controller didn't catch all the
> > inbound clock ticks and thus counted less inbound data than it was
> > set up to receive. The controller thus waits for more data.
> 
> The flash chip can transfer data as long as you keep the clock going,
> especially when you transfer 64k off a 4M flash.
> 
> The read command is bound just by stopping the clock. There is always
> more data to be had.

Sure, if you keep clocking the chip, the data will keep going. Is the
chip being clocked ?

Doesn't the PL330 have some kind of a counter register where you can check
how much data were received so far ? That should be sufficient to verify
this hypothesis of mine.

> >> Data
> >> is left in FIFO which causes subsequent commands to fail since garbage
> >> is returned instead of command reply. Also subsequent read may cause
> >> I/O error or or return an empty page depending on the garbage around.
> > 
> > So the driver for the DMA controller might need to be augmented to handle
> > this case -- add a timeout and in case DMA times out, drain the FIFO to
> > make sure subsequent transfers do not fail.
> 
> There is no way to add timeout in the DMA driver since it does not
> know the SPI clock.
> 
> The timeout is handled by the SPI driver and it should be possible to
> augment it to drain the FIFO when DMA fails so long as FIFO level is
> readable somewhere.

If the DMA doesn't complete in certain amount of time, it should time out
I'd say. Don't you think ?

> >> - the I/O errors are not checked in spi-nor at all which leads to
> >> silent data corruption.
> >> 
> >> On a suggestion that this may improve reliability I changed the
> >> s3c64xx driver to use DMA for all transfers. This caused
> >> identification to fail in spin-nor because the ID was prefixed with
> >> extra 00  byte. Testing with spidev confirmed that everything is
> >> prefixed with extra 00.
> > 
> > The determinism of this is in fact excellent news.
> > 
> >> Also when the DMA controller locked up no
> >> transfers were possible anymore. When DMA was not used for sending
> >> commands the controller would recover on next command. I made the
> >> option to always use DMA configurable and it turns out that the
> >> returned data is prefixed with 00 only when no transfer without DMA
> >> was ever made. Loading the spi-nor driver with the dma-only option off
> >> and then with dma-only option on results in correct operation. Only
> >> loading the dma-only driver first causes the 00 prefix.
> > 
> > Can we conclude that the PIO codepath somehow programs a register
> > somewhere which gets rid of this 0x00 prefix ? If so, this should then
> > also be part of the DMA codepath, or even better, this should be set in
> > probe() somewhere.
> 
> Yes, it looks like it.

Did you find what this could be please ?