* Bluetooth agent can't get default adapter
@ 2015-12-17 6:24 Ankur Tyagi
2015-12-17 22:38 ` Ankur Tyagi
0 siblings, 1 reply; 6+ messages in thread
From: Ankur Tyagi @ 2015-12-17 6:24 UTC (permalink / raw)
To: meta-arago
[-- Attachment #1: Type: text/plain, Size: 1861 bytes --]
Hi,
I am trying to use WL1835 bluetooth with AM335x EVM. Software is
meta-arago daisy.
When I run bluetooth agent, I get error "Can't get default adapter"
Following is the sequence of commands:
root@am335x-evm:~# bluetoothd
root@am335x-evm:~# hciconfig hci0 up
[ 944.008593] (stc): chnl_id list empty :4
[ 944.012749] (stk) : st_kim_start(stk) :ldisc_install = 1uim:poll broke
due to event 10(PRI:2/ERR:8)
uim:read 1 from install
uim:@ st_uart_config
uim: signal received, opening /dev/ttyS1
uim:@ set_baud_rate
uim:set_baud_rate() done
uim:Setting speed to 3000000
uim:@ read_command_complete
uim: Command complete started
uim:@ read_hci_event
uim: read_hci_event
uim:Command complete done
[ 944.180311] (stc): st_tty_open
uim:Speed changing to 3000000, 1
uim:@ set_custom_baud_rate
(stk) :line discipline installeduim:Installed N_TI_WL Line displine
[ 944.194437] (stk) :TIInit_11.8.32.bts
uim:begin polling...
(stk) :change remote baud rate command in firmware
[ 944.214516] (stk) :skipping the wait event of change remote baud[
944.928331] (stc): add_channel_to_table: id 4
[ 944.932771] (stc): add_channel_to_table: id 2
[ 944.937149] (stc): add_channel_to_table: id 3
root@am335x-evm:~# hcitool scan
Scanning ...
00:02:72:E3:0F:7F RS232 Dongle Slave
root@am335x-evm:~# agent hci0 00:02:72:E3:0F:7F
Can't get default adapter
No such adapter
root@am335x-evm:~# dmesg | grep Bluetooth
[ 3.475348] Bluetooth: Core ver 2.18
[ 3.483613] Bluetooth: HCI device and connection manager initialized
[ 3.663793] Bluetooth: HCI socket layer initialized
[ 3.668731] Bluetooth: L2CAP socket layer initialized
[ 3.814838] Bluetooth: SCO socket layer initialized
[ 16.667945] Bluetooth: st_register failed -22
What am I missing here ?
thanks
Ankur
[-- Attachment #2: Type: text/html, Size: 2159 bytes --]
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: Bluetooth agent can't get default adapter
2015-12-17 6:24 Bluetooth agent can't get default adapter Ankur Tyagi
@ 2015-12-17 22:38 ` Ankur Tyagi
2015-12-17 23:20 ` Denys Dmytriyenko
0 siblings, 1 reply; 6+ messages in thread
From: Ankur Tyagi @ 2015-12-17 22:38 UTC (permalink / raw)
To: meta-arago
[-- Attachment #1: Type: text/plain, Size: 4033 bytes --]
Further debugged it to check dbus and bluez service
dbus is running and service file is also present
root@am335x-evm:~# cat /usr/share/dbus-1/system-services/org.bluez.service
[D-BUS Service]
Name=org.bluez
Exec=/bin/false
User=root
SystemdService=dbus-org.bluez.service
root@am335x-evm:~# cat /etc/dbus-1/system.d/bluetooth.conf
<!-- This configuration file specifies the required security policies
for Bluetooth core daemon to work. -->
<!DOCTYPE busconfig PUBLIC "-//freedesktop//DTD D-BUS Bus Configuration
1.0//EN"
"<a href="http://www.freedesktop.org/standards/dbus/1.0/busconfig.dtd">
www.freedesktop.org/.../busconfig.dtd"></a>
<busconfig>
<!-- ../system.conf have denied everything, so we just punch some holes
-->
<policy user="root">
<allow own="org.bluez"/>
<allow send_destination="org.bluez"/>
<allow send_interface="org.bluez.Agent"/>
<allow send_interface="org.bluez.PasskeyAgent"/>
</policy>
<policy context="default">
<allow own="org.bluez"/>
<allow send_destination="org.bluez"/>
<allow send_interface="org.bluez.Agent"/>
</policy>
</busconfig>
When I run bluetoothd, I can see org.bluez in dbus list
root@am335x-evm:~# dbus-send --system --dest=org.freedesktop.DBus
--type=method_call --print-reply /org/freedesktop/DBus
org.freedesktop.DBus.ListNames
method return sender=org.freedesktop.DBus -> dest=:1.4 reply_serial=2
array [
string "org.freedesktop.DBus"
string ":1.4"
string ":1.0"
string "org.bluez"
]
But when I query default adapter, I don't get a response
root@am335x-evm:~# dbus-send --system --print-reply --dest=org.bluez /
org.bluez.Manager.ListAdapters
method return sender=:1.0 -> dest=:1.5 reply_serial=2
array [
]
What's missing to get it working ? Any help is appreciated
Thanks
Ankur
"Knowledge is knowing tomato is a fruit, wisdom is not putting it in a
fruit salad"
On Thu, Dec 17, 2015 at 7:24 PM, Ankur Tyagi <ankur.tyagi85@gmail.com>
wrote:
>
> Hi,
>
> I am trying to use WL1835 bluetooth with AM335x EVM. Software is
> meta-arago daisy.
>
> When I run bluetooth agent, I get error "Can't get default adapter"
>
> Following is the sequence of commands:
>
> root@am335x-evm:~# bluetoothd
>
> root@am335x-evm:~# hciconfig hci0 up
>
> [ 944.008593] (stc): chnl_id list empty :4
> [ 944.012749] (stk) : st_kim_start(stk) :ldisc_install = 1uim:poll broke
> due to event 10(PRI:2/ERR:8)
>
> uim:read 1 from install
>
> uim:@ st_uart_config
> uim: signal received, opening /dev/ttyS1
> uim:@ set_baud_rate
> uim:set_baud_rate() done
> uim:Setting speed to 3000000
> uim:@ read_command_complete
> uim: Command complete started
> uim:@ read_hci_event
> uim: read_hci_event
> uim:Command complete done
> [ 944.180311] (stc): st_tty_open
> uim:Speed changing to 3000000, 1
> uim:@ set_custom_baud_rate
> (stk) :line discipline installeduim:Installed N_TI_WL Line displine
> [ 944.194437] (stk) :TIInit_11.8.32.bts
> uim:begin polling...
> (stk) :change remote baud rate command in firmware
> [ 944.214516] (stk) :skipping the wait event of change remote baud[
> 944.928331] (stc): add_channel_to_table: id 4
> [ 944.932771] (stc): add_channel_to_table: id 2
> [ 944.937149] (stc): add_channel_to_table: id 3
>
> root@am335x-evm:~# hcitool scan
> Scanning ...
> 00:02:72:E3:0F:7F RS232 Dongle Slave
>
> root@am335x-evm:~# agent hci0 00:02:72:E3:0F:7F
> Can't get default adapter
> No such adapter
>
> root@am335x-evm:~# dmesg | grep Bluetooth
> [ 3.475348] Bluetooth: Core ver 2.18
> [ 3.483613] Bluetooth: HCI device and connection manager initialized
> [ 3.663793] Bluetooth: HCI socket layer initialized
> [ 3.668731] Bluetooth: L2CAP socket layer initialized
> [ 3.814838] Bluetooth: SCO socket layer initialized
> [ 16.667945] Bluetooth: st_register failed -22
>
> What am I missing here ?
>
> thanks
> Ankur
>
[-- Attachment #2: Type: text/html, Size: 10333 bytes --]
^ permalink raw reply [flat|nested] 6+ messages in thread
* Bluetooth agent can't get default adapter
@ 2015-12-17 22:40 Ankur Tyagi
0 siblings, 0 replies; 6+ messages in thread
From: Ankur Tyagi @ 2015-12-17 22:40 UTC (permalink / raw)
To: openembedded-devel
Hi,
I am trying to use WL1835 bluetooth with AM335x EVM. Software is meta-arago
daisy.
When I run bluetooth agent, I get error "Can't get default adapter"
Following is the sequence of commands:
root@am335x-evm:~# bluetoothd
root@am335x-evm:~# hciconfig hci0 up
[ 944.008593] (stc): chnl_id list empty :4
[ 944.012749] (stk) : st_kim_start(stk) :ldisc_install = 1uim:poll broke
due to event 10(PRI:2/ERR:8)
uim:read 1 from install
uim:@ st_uart_config
uim: signal received, opening /dev/ttyS1
uim:@ set_baud_rate
uim:set_baud_rate() done
uim:Setting speed to 3000000
uim:@ read_command_complete
uim: Command complete started
uim:@ read_hci_event
uim: read_hci_event
uim:Command complete done
[ 944.180311] (stc): st_tty_open
uim:Speed changing to 3000000, 1
uim:@ set_custom_baud_rate
(stk) :line discipline installeduim:Installed N_TI_WL Line displine
[ 944.194437] (stk) :TIInit_11.8.32.bts
uim:begin polling...
(stk) :change remote baud rate command in firmware
[ 944.214516] (stk) :skipping the wait event of change remote baud[
944.928331] (stc): add_channel_to_table: id 4
[ 944.932771] (stc): add_channel_to_table: id 2
[ 944.937149] (stc): add_channel_to_table: id 3
root@am335x-evm:~# hcitool scan
Scanning ...
00:02:72:E3:0F:7F RS232 Dongle Slave
root@am335x-evm:~# agent hci0 00:02:72:E3:0F:7F
Can't get default adapter
No such adapter
root@am335x-evm:~# dmesg | grep Bluetooth
[ 3.475348] Bluetooth: Core ver 2.18
[ 3.483613] Bluetooth: HCI device and connection manager initialized
[ 3.663793] Bluetooth: HCI socket layer initialized
[ 3.668731] Bluetooth: L2CAP socket layer initialized
[ 3.814838] Bluetooth: SCO socket layer initialized
[ 16.667945] Bluetooth: st_register failed -22
dbus is running and service file is also present
root@am335x-evm:~# cat /usr/share/dbus-1/system-services/org.bluez.service
[D-BUS Service]
Name=org.bluez
Exec=/bin/false
User=root
SystemdService=dbus-org.bluez.service
root@am335x-evm:~# cat /etc/dbus-1/system.d/bluetooth.conf
<!-- This configuration file specifies the required security policies
for Bluetooth core daemon to work. -->
<!DOCTYPE busconfig PUBLIC "-//freedesktop//DTD D-BUS Bus Configuration
1.0//EN"
"<a href="http://www.freedesktop.org/standards/dbus/1.0/busconfig.dtd">
www.freedesktop.org/.../busconfig.dtd"></a>
<busconfig>
<!-- ../system.conf have denied everything, so we just punch some holes
-->
<policy user="root">
<allow own="org.bluez"/>
<allow send_destination="org.bluez"/>
<allow send_interface="org.bluez.Agent"/>
<allow send_interface="org.bluez.PasskeyAgent"/>
</policy>
<policy context="default">
<allow own="org.bluez"/>
<allow send_destination="org.bluez"/>
<allow send_interface="org.bluez.Agent"/>
</policy>
</busconfig>
When I run bluetoothd, I can see org.bluez in dbus list
root@am335x-evm:~# dbus-send --system --dest=org.freedesktop.DBus
--type=method_call --print-reply /org/freedesktop/DBus
org.freedesktop.DBus.ListNames
method return sender=org.freedesktop.DBus -> dest=:1.4 reply_serial=2
array [
string "org.freedesktop.DBus"
string ":1.4"
string ":1.0"
string "org.bluez"
]
But when I query default adapter, I don't get a response
root@am335x-evm:~# dbus-send --system --print-reply --dest=org.bluez /
org.bluez.Manager.ListAdapters
method return sender=:1.0 -> dest=:1.5 reply_serial=2
array [
]
What's missing to get it working ? Any help is appreciated
Thanks
Ankur
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: Bluetooth agent can't get default adapter
2015-12-17 22:38 ` Ankur Tyagi
@ 2015-12-17 23:20 ` Denys Dmytriyenko
2015-12-17 23:58 ` Ankur Tyagi
0 siblings, 1 reply; 6+ messages in thread
From: Denys Dmytriyenko @ 2015-12-17 23:20 UTC (permalink / raw)
To: Ankur Tyagi; +Cc: meta-arago
Any specific reason you are trying 3.14? Can you try 4.1 instead?
--
Denys
On Fri, Dec 18, 2015 at 11:38:40AM +1300, Ankur Tyagi wrote:
> Further debugged it to check dbus and bluez service
>
>
> dbus is running and service file is also present
>
> root@am335x-evm:~# cat /usr/share/dbus-1/system-services/org.bluez.service
> [D-BUS Service]
> Name=org.bluez
> Exec=/bin/false
> User=root
> SystemdService=dbus-org.bluez.service
>
> root@am335x-evm:~# cat /etc/dbus-1/system.d/bluetooth.conf
> <!-- This configuration file specifies the required security policies
> for Bluetooth core daemon to work. -->
> <!DOCTYPE busconfig PUBLIC "-//freedesktop//DTD D-BUS Bus Configuration
> 1.0//EN"
> "<a href="http://www.freedesktop.org/standards/dbus/1.0/busconfig.dtd">
> www.freedesktop.org/.../busconfig.dtd"></a>
> <busconfig>
> <!-- ../system.conf have denied everything, so we just punch some holes
> -->
> <policy user="root">
> <allow own="org.bluez"/>
> <allow send_destination="org.bluez"/>
> <allow send_interface="org.bluez.Agent"/>
> <allow send_interface="org.bluez.PasskeyAgent"/>
> </policy>
>
> <policy context="default">
> <allow own="org.bluez"/>
> <allow send_destination="org.bluez"/>
> <allow send_interface="org.bluez.Agent"/>
> </policy>
>
> </busconfig>
>
>
> When I run bluetoothd, I can see org.bluez in dbus list
>
> root@am335x-evm:~# dbus-send --system --dest=org.freedesktop.DBus
> --type=method_call --print-reply /org/freedesktop/DBus
> org.freedesktop.DBus.ListNames
> method return sender=org.freedesktop.DBus -> dest=:1.4 reply_serial=2
> array [
> string "org.freedesktop.DBus"
> string ":1.4"
> string ":1.0"
> string "org.bluez"
> ]
>
> But when I query default adapter, I don't get a response
>
> root@am335x-evm:~# dbus-send --system --print-reply --dest=org.bluez /
> org.bluez.Manager.ListAdapters
> method return sender=:1.0 -> dest=:1.5 reply_serial=2
> array [
> ]
>
> What's missing to get it working ? Any help is appreciated
>
> Thanks
> Ankur
>
> "Knowledge is knowing tomato is a fruit, wisdom is not putting it in a
> fruit salad"
>
> On Thu, Dec 17, 2015 at 7:24 PM, Ankur Tyagi <ankur.tyagi85@gmail.com>
> wrote:
>
> >
> > Hi,
> >
> > I am trying to use WL1835 bluetooth with AM335x EVM. Software is
> > meta-arago daisy.
> >
> > When I run bluetooth agent, I get error "Can't get default adapter"
> >
> > Following is the sequence of commands:
> >
> > root@am335x-evm:~# bluetoothd
> >
> > root@am335x-evm:~# hciconfig hci0 up
> >
> > [ 944.008593] (stc): chnl_id list empty :4
> > [ 944.012749] (stk) : st_kim_start(stk) :ldisc_install = 1uim:poll broke
> > due to event 10(PRI:2/ERR:8)
> >
> > uim:read 1 from install
> >
> > uim:@ st_uart_config
> > uim: signal received, opening /dev/ttyS1
> > uim:@ set_baud_rate
> > uim:set_baud_rate() done
> > uim:Setting speed to 3000000
> > uim:@ read_command_complete
> > uim: Command complete started
> > uim:@ read_hci_event
> > uim: read_hci_event
> > uim:Command complete done
> > [ 944.180311] (stc): st_tty_open
> > uim:Speed changing to 3000000, 1
> > uim:@ set_custom_baud_rate
> > (stk) :line discipline installeduim:Installed N_TI_WL Line displine
> > [ 944.194437] (stk) :TIInit_11.8.32.bts
> > uim:begin polling...
> > (stk) :change remote baud rate command in firmware
> > [ 944.214516] (stk) :skipping the wait event of change remote baud[
> > 944.928331] (stc): add_channel_to_table: id 4
> > [ 944.932771] (stc): add_channel_to_table: id 2
> > [ 944.937149] (stc): add_channel_to_table: id 3
> >
> > root@am335x-evm:~# hcitool scan
> > Scanning ...
> > 00:02:72:E3:0F:7F RS232 Dongle Slave
> >
> > root@am335x-evm:~# agent hci0 00:02:72:E3:0F:7F
> > Can't get default adapter
> > No such adapter
> >
> > root@am335x-evm:~# dmesg | grep Bluetooth
> > [ 3.475348] Bluetooth: Core ver 2.18
> > [ 3.483613] Bluetooth: HCI device and connection manager initialized
> > [ 3.663793] Bluetooth: HCI socket layer initialized
> > [ 3.668731] Bluetooth: L2CAP socket layer initialized
> > [ 3.814838] Bluetooth: SCO socket layer initialized
> > [ 16.667945] Bluetooth: st_register failed -22
> >
> > What am I missing here ?
> >
> > thanks
> > Ankur
> >
> _______________________________________________
> meta-arago mailing list
> meta-arago@arago-project.org
> http://arago-project.org/cgi-bin/mailman/listinfo/meta-arago
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: Bluetooth agent can't get default adapter
2015-12-17 23:20 ` Denys Dmytriyenko
@ 2015-12-17 23:58 ` Ankur Tyagi
2016-01-06 21:19 ` Ankur Tyagi
0 siblings, 1 reply; 6+ messages in thread
From: Ankur Tyagi @ 2015-12-17 23:58 UTC (permalink / raw)
To: Denys Dmytriyenko; +Cc: meta-arago
[-- Attachment #1: Type: text/plain, Size: 5253 bytes --]
Because our product is based on 3.14
Now we are trying to add Wi-Fi, Bluetooth capability to it
I am happy to back-port some stuff from 4.1 if it can fix it
regards
Ankur
"Knowledge is knowing tomato is a fruit, wisdom is not putting it in a
fruit salad"
On Fri, Dec 18, 2015 at 12:20 PM, Denys Dmytriyenko <denys@ti.com> wrote:
> Any specific reason you are trying 3.14? Can you try 4.1 instead?
>
> --
> Denys
>
>
> On Fri, Dec 18, 2015 at 11:38:40AM +1300, Ankur Tyagi wrote:
> > Further debugged it to check dbus and bluez service
> >
> >
> > dbus is running and service file is also present
> >
> > root@am335x-evm:~# cat
> /usr/share/dbus-1/system-services/org.bluez.service
> > [D-BUS Service]
> > Name=org.bluez
> > Exec=/bin/false
> > User=root
> > SystemdService=dbus-org.bluez.service
> >
> > root@am335x-evm:~# cat /etc/dbus-1/system.d/bluetooth.conf
> > <!-- This configuration file specifies the required security policies
> > for Bluetooth core daemon to work. -->
> > <!DOCTYPE busconfig PUBLIC "-//freedesktop//DTD D-BUS Bus Configuration
> > 1.0//EN"
> > "<a href="http://www.freedesktop.org/standards/dbus/1.0/busconfig.dtd">
> > www.freedesktop.org/.../busconfig.dtd"></a>
> > <busconfig>
> > <!-- ../system.conf have denied everything, so we just punch some holes
> > -->
> > <policy user="root">
> > <allow own="org.bluez"/>
> > <allow send_destination="org.bluez"/>
> > <allow send_interface="org.bluez.Agent"/>
> > <allow send_interface="org.bluez.PasskeyAgent"/>
> > </policy>
> >
> > <policy context="default">
> > <allow own="org.bluez"/>
> > <allow send_destination="org.bluez"/>
> > <allow send_interface="org.bluez.Agent"/>
> > </policy>
> >
> > </busconfig>
> >
> >
> > When I run bluetoothd, I can see org.bluez in dbus list
> >
> > root@am335x-evm:~# dbus-send --system --dest=org.freedesktop.DBus
> > --type=method_call --print-reply /org/freedesktop/DBus
> > org.freedesktop.DBus.ListNames
> > method return sender=org.freedesktop.DBus -> dest=:1.4 reply_serial=2
> > array [
> > string "org.freedesktop.DBus"
> > string ":1.4"
> > string ":1.0"
> > string "org.bluez"
> > ]
> >
> > But when I query default adapter, I don't get a response
> >
> > root@am335x-evm:~# dbus-send --system --print-reply --dest=org.bluez /
> > org.bluez.Manager.ListAdapters
> > method return sender=:1.0 -> dest=:1.5 reply_serial=2
> > array [
> > ]
> >
> > What's missing to get it working ? Any help is appreciated
> >
> > Thanks
> > Ankur
> >
> > "Knowledge is knowing tomato is a fruit, wisdom is not putting it in a
> > fruit salad"
> >
> > On Thu, Dec 17, 2015 at 7:24 PM, Ankur Tyagi <ankur.tyagi85@gmail.com>
> > wrote:
> >
> > >
> > > Hi,
> > >
> > > I am trying to use WL1835 bluetooth with AM335x EVM. Software is
> > > meta-arago daisy.
> > >
> > > When I run bluetooth agent, I get error "Can't get default adapter"
> > >
> > > Following is the sequence of commands:
> > >
> > > root@am335x-evm:~# bluetoothd
> > >
> > > root@am335x-evm:~# hciconfig hci0 up
> > >
> > > [ 944.008593] (stc): chnl_id list empty :4
> > > [ 944.012749] (stk) : st_kim_start(stk) :ldisc_install = 1uim:poll
> broke
> > > due to event 10(PRI:2/ERR:8)
> > >
> > > uim:read 1 from install
> > >
> > > uim:@ st_uart_config
> > > uim: signal received, opening /dev/ttyS1
> > > uim:@ set_baud_rate
> > > uim:set_baud_rate() done
> > > uim:Setting speed to 3000000
> > > uim:@ read_command_complete
> > > uim: Command complete started
> > > uim:@ read_hci_event
> > > uim: read_hci_event
> > > uim:Command complete done
> > > [ 944.180311] (stc): st_tty_open
> > > uim:Speed changing to 3000000, 1
> > > uim:@ set_custom_baud_rate
> > > (stk) :line discipline installeduim:Installed N_TI_WL Line displine
> > > [ 944.194437] (stk) :TIInit_11.8.32.bts
> > > uim:begin polling...
> > > (stk) :change remote baud rate command in firmware
> > > [ 944.214516] (stk) :skipping the wait event of change remote baud[
> > > 944.928331] (stc): add_channel_to_table: id 4
> > > [ 944.932771] (stc): add_channel_to_table: id 2
> > > [ 944.937149] (stc): add_channel_to_table: id 3
> > >
> > > root@am335x-evm:~# hcitool scan
> > > Scanning ...
> > > 00:02:72:E3:0F:7F RS232 Dongle Slave
> > >
> > > root@am335x-evm:~# agent hci0 00:02:72:E3:0F:7F
> > > Can't get default adapter
> > > No such adapter
> > >
> > > root@am335x-evm:~# dmesg | grep Bluetooth
> > > [ 3.475348] Bluetooth: Core ver 2.18
> > > [ 3.483613] Bluetooth: HCI device and connection manager initialized
> > > [ 3.663793] Bluetooth: HCI socket layer initialized
> > > [ 3.668731] Bluetooth: L2CAP socket layer initialized
> > > [ 3.814838] Bluetooth: SCO socket layer initialized
> > > [ 16.667945] Bluetooth: st_register failed -22
> > >
> > > What am I missing here ?
> > >
> > > thanks
> > > Ankur
> > >
>
> > _______________________________________________
> > meta-arago mailing list
> > meta-arago@arago-project.org
> > http://arago-project.org/cgi-bin/mailman/listinfo/meta-arago
>
>
[-- Attachment #2: Type: text/html, Size: 8130 bytes --]
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: Bluetooth agent can't get default adapter
2015-12-17 23:58 ` Ankur Tyagi
@ 2016-01-06 21:19 ` Ankur Tyagi
0 siblings, 0 replies; 6+ messages in thread
From: Ankur Tyagi @ 2016-01-06 21:19 UTC (permalink / raw)
To: Denys Dmytriyenko; +Cc: meta-arago
[-- Attachment #1: Type: text/plain, Size: 5619 bytes --]
Managed to get it working by disabling TI's shared transport in kernel
along with kim, uim.
On Fri, Dec 18, 2015 at 12:58 PM, Ankur Tyagi <ankur.tyagi85@gmail.com>
wrote:
> Because our product is based on 3.14
>
> Now we are trying to add Wi-Fi, Bluetooth capability to it
>
> I am happy to back-port some stuff from 4.1 if it can fix it
>
> regards
> Ankur
>
> "Knowledge is knowing tomato is a fruit, wisdom is not putting it in a
> fruit salad"
>
> On Fri, Dec 18, 2015 at 12:20 PM, Denys Dmytriyenko <denys@ti.com> wrote:
>
>> Any specific reason you are trying 3.14? Can you try 4.1 instead?
>>
>> --
>> Denys
>>
>>
>> On Fri, Dec 18, 2015 at 11:38:40AM +1300, Ankur Tyagi wrote:
>> > Further debugged it to check dbus and bluez service
>> >
>> >
>> > dbus is running and service file is also present
>> >
>> > root@am335x-evm:~# cat
>> /usr/share/dbus-1/system-services/org.bluez.service
>> > [D-BUS Service]
>> > Name=org.bluez
>> > Exec=/bin/false
>> > User=root
>> > SystemdService=dbus-org.bluez.service
>> >
>> > root@am335x-evm:~# cat /etc/dbus-1/system.d/bluetooth.conf
>> > <!-- This configuration file specifies the required security policies
>> > for Bluetooth core daemon to work. -->
>> > <!DOCTYPE busconfig PUBLIC "-//freedesktop//DTD D-BUS Bus Configuration
>> > 1.0//EN"
>> > "<a href="http://www.freedesktop.org/standards/dbus/1.0/busconfig.dtd
>> ">
>> > www.freedesktop.org/.../busconfig.dtd"></a>
>> > <busconfig>
>> > <!-- ../system.conf have denied everything, so we just punch some
>> holes
>> > -->
>> > <policy user="root">
>> > <allow own="org.bluez"/>
>> > <allow send_destination="org.bluez"/>
>> > <allow send_interface="org.bluez.Agent"/>
>> > <allow send_interface="org.bluez.PasskeyAgent"/>
>> > </policy>
>> >
>> > <policy context="default">
>> > <allow own="org.bluez"/>
>> > <allow send_destination="org.bluez"/>
>> > <allow send_interface="org.bluez.Agent"/>
>> > </policy>
>> >
>> > </busconfig>
>> >
>> >
>> > When I run bluetoothd, I can see org.bluez in dbus list
>> >
>> > root@am335x-evm:~# dbus-send --system --dest=org.freedesktop.DBus
>> > --type=method_call --print-reply /org/freedesktop/DBus
>> > org.freedesktop.DBus.ListNames
>> > method return sender=org.freedesktop.DBus -> dest=:1.4 reply_serial=2
>> > array [
>> > string "org.freedesktop.DBus"
>> > string ":1.4"
>> > string ":1.0"
>> > string "org.bluez"
>> > ]
>> >
>> > But when I query default adapter, I don't get a response
>> >
>> > root@am335x-evm:~# dbus-send --system --print-reply --dest=org.bluez /
>> > org.bluez.Manager.ListAdapters
>> > method return sender=:1.0 -> dest=:1.5 reply_serial=2
>> > array [
>> > ]
>> >
>> > What's missing to get it working ? Any help is appreciated
>> >
>> > Thanks
>> > Ankur
>> >
>> > "Knowledge is knowing tomato is a fruit, wisdom is not putting it in a
>> > fruit salad"
>> >
>> > On Thu, Dec 17, 2015 at 7:24 PM, Ankur Tyagi <ankur.tyagi85@gmail.com>
>> > wrote:
>> >
>> > >
>> > > Hi,
>> > >
>> > > I am trying to use WL1835 bluetooth with AM335x EVM. Software is
>> > > meta-arago daisy.
>> > >
>> > > When I run bluetooth agent, I get error "Can't get default adapter"
>> > >
>> > > Following is the sequence of commands:
>> > >
>> > > root@am335x-evm:~# bluetoothd
>> > >
>> > > root@am335x-evm:~# hciconfig hci0 up
>> > >
>> > > [ 944.008593] (stc): chnl_id list empty :4
>> > > [ 944.012749] (stk) : st_kim_start(stk) :ldisc_install = 1uim:poll
>> broke
>> > > due to event 10(PRI:2/ERR:8)
>> > >
>> > > uim:read 1 from install
>> > >
>> > > uim:@ st_uart_config
>> > > uim: signal received, opening /dev/ttyS1
>> > > uim:@ set_baud_rate
>> > > uim:set_baud_rate() done
>> > > uim:Setting speed to 3000000
>> > > uim:@ read_command_complete
>> > > uim: Command complete started
>> > > uim:@ read_hci_event
>> > > uim: read_hci_event
>> > > uim:Command complete done
>> > > [ 944.180311] (stc): st_tty_open
>> > > uim:Speed changing to 3000000, 1
>> > > uim:@ set_custom_baud_rate
>> > > (stk) :line discipline installeduim:Installed N_TI_WL Line displine
>> > > [ 944.194437] (stk) :TIInit_11.8.32.bts
>> > > uim:begin polling...
>> > > (stk) :change remote baud rate command in firmware
>> > > [ 944.214516] (stk) :skipping the wait event of change remote baud[
>> > > 944.928331] (stc): add_channel_to_table: id 4
>> > > [ 944.932771] (stc): add_channel_to_table: id 2
>> > > [ 944.937149] (stc): add_channel_to_table: id 3
>> > >
>> > > root@am335x-evm:~# hcitool scan
>> > > Scanning ...
>> > > 00:02:72:E3:0F:7F RS232 Dongle Slave
>> > >
>> > > root@am335x-evm:~# agent hci0 00:02:72:E3:0F:7F
>> > > Can't get default adapter
>> > > No such adapter
>> > >
>> > > root@am335x-evm:~# dmesg | grep Bluetooth
>> > > [ 3.475348] Bluetooth: Core ver 2.18
>> > > [ 3.483613] Bluetooth: HCI device and connection manager
>> initialized
>> > > [ 3.663793] Bluetooth: HCI socket layer initialized
>> > > [ 3.668731] Bluetooth: L2CAP socket layer initialized
>> > > [ 3.814838] Bluetooth: SCO socket layer initialized
>> > > [ 16.667945] Bluetooth: st_register failed -22
>> > >
>> > > What am I missing here ?
>> > >
>> > > thanks
>> > > Ankur
>> > >
>>
>> > _______________________________________________
>> > meta-arago mailing list
>> > meta-arago@arago-project.org
>> > http://arago-project.org/cgi-bin/mailman/listinfo/meta-arago
>>
>>
>
[-- Attachment #2: Type: text/html, Size: 8813 bytes --]
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2016-01-06 21:19 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2015-12-17 6:24 Bluetooth agent can't get default adapter Ankur Tyagi
2015-12-17 22:38 ` Ankur Tyagi
2015-12-17 23:20 ` Denys Dmytriyenko
2015-12-17 23:58 ` Ankur Tyagi
2016-01-06 21:19 ` Ankur Tyagi
-- strict thread matches above, loose matches on Subject: below --
2015-12-17 22:40 Ankur Tyagi
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.