From: shawnguo@kernel.org (Shawn Guo)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCHv2 7/8] ARM: dts: imx6: add support for more Ka-Ro electronics modules
Date: Thu, 31 Mar 2016 14:10:23 +0800 [thread overview]
Message-ID: <20160331061023.GO28207@tiger> (raw)
In-Reply-To: <1457424244-14549-8-git-send-email-LW@KARO-electronics.de>
On Tue, Mar 08, 2016 at 09:04:03AM +0100, Lothar Wa?mann wrote:
> Add support for the following i.MX6 based modules from Ka-Ro
> electronics GmbH:
> TX6S-8034:
> Processor Freescale i.MX 6 Solo, 800MHz
> RAM 256MiB DDR3 SDRAM
> ROM 128MiB NAND Flash
> Power supply Single 3.1V to 5.5V
> Size 31mm SO-DIMM
> Temp. Range industrial grade (-40?C/-25?C to 105?C Tj)
>
> TX6S-8035:
> Processor Freescale i.MX 6 Solo, 800MHz
> RAM 512MiB DDR3 SDRAM
> ROM 4GiB eMMC
> Power supply Single 3.1V to 5.5V
> Size 31mm SO-DIMM
> Temp. Range industrial grade (-40?C/-25?C to 105?C Tj)
>
> TX6U-8033:
> Processor Freescale i.MX 6 Dual Lite, 800MHz
> RAM 1GiB DDR3 SDRAM
> ROM 4GiB eMMC
> Power supply Single 3.1V to 5.5V
> Size 31mm SO-DIMM
> Temp. Range industrial grade (-40?C/-25?C to 105?C Tj)
>
> TX6Q-1036:
> Processor Freescale i.MX 6Quad, 1GHz
> RAM 1GB DDR3 SDRAM 64-bit
> ROM 8GiB eMMC
> Power supply Single 3.1V to 5.5V
> Size 31mm SO-DIMM
> Temp. Range Extended Consumer Grade (-20?C to 105?C Tj)
>
> Signed-off-by: Lothar Wa?mann <LW@KARO-electronics.de>
> ---
> arch/arm/boot/dts/Makefile | 4 +
> arch/arm/boot/dts/imx6dl-tx6s-8034.dts | 249 ++++++++++++++++++++++++++++
> arch/arm/boot/dts/imx6dl-tx6s-8035.dts | 246 +++++++++++++++++++++++++++
> arch/arm/boot/dts/imx6dl-tx6u-8033.dts | 248 +++++++++++++++++++++++++++
> arch/arm/boot/dts/imx6q-tx6q-1036.dts | 295 +++++++++++++++++++++++++++++++++
> 5 files changed, 1042 insertions(+)
> create mode 100644 arch/arm/boot/dts/imx6dl-tx6s-8034.dts
> create mode 100644 arch/arm/boot/dts/imx6dl-tx6s-8035.dts
> create mode 100644 arch/arm/boot/dts/imx6dl-tx6u-8033.dts
> create mode 100644 arch/arm/boot/dts/imx6q-tx6q-1036.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 072294f..71b5cd3 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -320,6 +320,9 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
> imx6dl-sabrelite.dtb \
> imx6dl-sabresd.dtb \
> imx6dl-tx6dl-comtft.dtb \
> + imx6dl-tx6s-8034.dtb \
> + imx6dl-tx6s-8035.dtb \
> + imx6dl-tx6u-8033.dtb \
imx6dl-tx6u-8033.dtb should go after imx6dl-tx6u-801x.dtb?
Shawn
> imx6dl-tx6u-801x.dtb \
> imx6dl-tx6u-811x.dtb \
> imx6dl-udoo.dtb \
> @@ -360,6 +363,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
> imx6q-tx6q-1010-comtft.dtb \
> imx6q-tx6q-1020.dtb \
> imx6q-tx6q-1020-comtft.dtb \
> + imx6q-tx6q-1036.dtb \
> imx6q-tx6q-1110.dtb \
> imx6q-udoo.dtb \
> imx6q-wandboard.dtb \
> diff --git a/arch/arm/boot/dts/imx6dl-tx6s-8034.dts b/arch/arm/boot/dts/imx6dl-tx6s-8034.dts
> new file mode 100644
> index 0000000..0d3df6e
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6dl-tx6s-8034.dts
> @@ -0,0 +1,237 @@
> +/*
> + * Copyright 2015-2016 Lothar Wa?mann <LW@KARO-electronics.de>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License
> + * version 2 as published by the Free Software Foundation.
> + *
> + * This file is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +#include "imx6dl.dtsi"
> +#include "imx6qdl-tx6.dtsi"
> +
> +/ {
> + model = "Ka-Ro electronics TX6S-8034 Module";
> + compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl";
> +
> + aliases {
> + display = &display;
> + ipu1 = &ipu1;
> + };
> +
> + cpus {
> + /delete-node/ cpu at 1;
> + };
> +
> + backlight: backlight {
> + compatible = "pwm-backlight";
> + pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_lcd0_pwr>;
> + enable-gpios = <&gpio3 29 GPIO_ACTIVE_HIGH>;
> + power-supply = <®_lcd1_pwr>;
> + /*
> + * a poor man's way to create a 1:1 relationship between
> + * the PWM value and the actual duty cycle
> + */
> + brightness-levels = < 0 1 2 3 4 5 6 7 8 9
> + 10 11 12 13 14 15 16 17 18 19
> + 20 21 22 23 24 25 26 27 28 29
> + 30 31 32 33 34 35 36 37 38 39
> + 40 41 42 43 44 45 46 47 48 49
> + 50 51 52 53 54 55 56 57 58 59
> + 60 61 62 63 64 65 66 67 68 69
> + 70 71 72 73 74 75 76 77 78 79
> + 80 81 82 83 84 85 86 87 88 89
> + 90 91 92 93 94 95 96 97 98 99
> + 100>;
> + default-brightness-level = <50>;
> + };
> +
> + display: display at di0 {
> + compatible = "fsl,imx-parallel-display";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_disp0_2>;
> + interface-pix-fmt = "rgb24";
> + status = "okay";
> +
> + port {
> + display0_in: endpoint {
> + remote-endpoint = <&ipu1_di0_disp0>;
> + };
> + };
> +
> + display-timings {
> + native-mode = <&vga>;
> +
> + vga: VGA {
> + clock-frequency = <25200000>;
> + hactive = <640>;
> + vactive = <480>;
> + hback-porch = <48>;
> + hsync-len = <96>;
> + hfront-porch = <16>;
> + vback-porch = <31>;
> + vsync-len = <2>;
> + vfront-porch = <12>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ETV570 {
> + clock-frequency = <25200000>;
> + hactive = <640>;
> + vactive = <480>;
> + hback-porch = <114>;
> + hsync-len = <30>;
> + hfront-porch = <16>;
> + vback-porch = <32>;
> + vsync-len = <3>;
> + vfront-porch = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ET0350 {
> + clock-frequency = <6413760>;
> + hactive = <320>;
> + vactive = <240>;
> + hback-porch = <34>;
> + hsync-len = <34>;
> + hfront-porch = <20>;
> + vback-porch = <15>;
> + vsync-len = <3>;
> + vfront-porch = <4>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ET0430 {
> + clock-frequency = <9009000>;
> + hactive = <480>;
> + vactive = <272>;
> + hback-porch = <2>;
> + hsync-len = <41>;
> + hfront-porch = <2>;
> + vback-porch = <2>;
> + vsync-len = <10>;
> + vfront-porch = <2>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <1>;
> + };
> +
> + ET0500 {
> + clock-frequency = <33264000>;
> + hactive = <800>;
> + vactive = <480>;
> + hback-porch = <88>;
> + hsync-len = <128>;
> + hfront-porch = <40>;
> + vback-porch = <33>;
> + vsync-len = <2>;
> + vfront-porch = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ET0700 { /* same as ET0500 */
> + clock-frequency = <33264000>;
> + hactive = <800>;
> + vactive = <480>;
> + hback-porch = <88>;
> + hsync-len = <128>;
> + hfront-porch = <40>;
> + vback-porch = <33>;
> + vsync-len = <2>;
> + vfront-porch = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ETQ570 {
> + clock-frequency = <6596040>;
> + hactive = <320>;
> + vactive = <240>;
> + hback-porch = <38>;
> + hsync-len = <30>;
> + hfront-porch = <30>;
> + vback-porch = <16>;
> + vsync-len = <3>;
> + vfront-porch = <4>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> + };
> + };
> +};
> +
> +&ds1339 {
> + status = "disabled";
> +};
> +
> +&pinctrl_usdhc1 {
> + fsl,pins = <
> + MX6QDL_PAD_SD1_CMD__SD1_CMD 0x070b1
> + MX6QDL_PAD_SD1_CLK__SD1_CLK 0x07099
> + MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x070b1
> + MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x070b1
> + MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x070b1
> + MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x070b1
> + MX6QDL_PAD_SD3_CMD__GPIO7_IO02 0x170b0 /* SD1 CD */
> + >;
> +};
> +
> +&ipu1_di0_disp0 {
> + remote-endpoint = <&display0_in>;
> +};
> +
> +®_lcd0_pwr {
> + status = "disabled";
> +};
> diff --git a/arch/arm/boot/dts/imx6dl-tx6s-8035.dts b/arch/arm/boot/dts/imx6dl-tx6s-8035.dts
> new file mode 100644
> index 0000000..2f9efdb
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6dl-tx6s-8035.dts
> @@ -0,0 +1,253 @@
> +/*
> + * Copyright 2015-2016 Lothar Wa?mann <LW@KARO-electronics.de>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License
> + * version 2 as published by the Free Software Foundation.
> + *
> + * This file is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +#include "imx6dl.dtsi"
> +#include "imx6qdl-tx6.dtsi"
> +
> +/ {
> + model = "Ka-Ro electronics TX6S-8035 Module";
> + compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl";
> +
> + aliases {
> + display = &display;
> + ipu1 = &ipu1;
> + };
> +
> + cpus {
> + /delete-node/ cpu at 1;
> + };
> +
> + backlight: backlight {
> + compatible = "pwm-backlight";
> + pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_lcd0_pwr>;
> + enable-gpios = <&gpio3 29 GPIO_ACTIVE_HIGH>;
> + power-supply = <®_lcd1_pwr>;
> + /*
> + * a poor man's way to create a 1:1 relationship between
> + * the PWM value and the actual duty cycle
> + */
> + brightness-levels = < 0 1 2 3 4 5 6 7 8 9
> + 10 11 12 13 14 15 16 17 18 19
> + 20 21 22 23 24 25 26 27 28 29
> + 30 31 32 33 34 35 36 37 38 39
> + 40 41 42 43 44 45 46 47 48 49
> + 50 51 52 53 54 55 56 57 58 59
> + 60 61 62 63 64 65 66 67 68 69
> + 70 71 72 73 74 75 76 77 78 79
> + 80 81 82 83 84 85 86 87 88 89
> + 90 91 92 93 94 95 96 97 98 99
> + 100>;
> + default-brightness-level = <50>;
> + };
> +
> + display: display at di0 {
> + compatible = "fsl,imx-parallel-display";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_disp0_2>;
> + interface-pix-fmt = "rgb24";
> + status = "okay";
> +
> + port {
> + display0_in: endpoint {
> + remote-endpoint = <&ipu1_di0_disp0>;
> + };
> + };
> +
> + display-timings {
> + native-mode = <&vga>;
> +
> + vga: VGA {
> + clock-frequency = <25200000>;
> + hactive = <640>;
> + vactive = <480>;
> + hback-porch = <48>;
> + hsync-len = <96>;
> + hfront-porch = <16>;
> + vback-porch = <31>;
> + vsync-len = <2>;
> + vfront-porch = <12>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ETV570 {
> + clock-frequency = <25200000>;
> + hactive = <640>;
> + vactive = <480>;
> + hback-porch = <114>;
> + hsync-len = <30>;
> + hfront-porch = <16>;
> + vback-porch = <32>;
> + vsync-len = <3>;
> + vfront-porch = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ET0350 {
> + clock-frequency = <6413760>;
> + hactive = <320>;
> + vactive = <240>;
> + hback-porch = <34>;
> + hsync-len = <34>;
> + hfront-porch = <20>;
> + vback-porch = <15>;
> + vsync-len = <3>;
> + vfront-porch = <4>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ET0430 {
> + clock-frequency = <9009000>;
> + hactive = <480>;
> + vactive = <272>;
> + hback-porch = <2>;
> + hsync-len = <41>;
> + hfront-porch = <2>;
> + vback-porch = <2>;
> + vsync-len = <10>;
> + vfront-porch = <2>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <1>;
> + };
> +
> + ET0500 {
> + clock-frequency = <33264000>;
> + hactive = <800>;
> + vactive = <480>;
> + hback-porch = <88>;
> + hsync-len = <128>;
> + hfront-porch = <40>;
> + vback-porch = <33>;
> + vsync-len = <2>;
> + vfront-porch = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ET0700 { /* same as ET0500 */
> + clock-frequency = <33264000>;
> + hactive = <800>;
> + vactive = <480>;
> + hback-porch = <88>;
> + hsync-len = <128>;
> + hfront-porch = <40>;
> + vback-porch = <33>;
> + vsync-len = <2>;
> + vfront-porch = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ETQ570 {
> + clock-frequency = <6596040>;
> + hactive = <320>;
> + vactive = <240>;
> + hback-porch = <38>;
> + hsync-len = <30>;
> + hfront-porch = <30>;
> + vback-porch = <16>;
> + vsync-len = <3>;
> + vfront-porch = <4>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> + };
> + };
> +};
> +
> +&ds1339 {
> + status = "disabled";
> +};
> +
> +&gpmi {
> + status = "disabled";
> +};
> +
> +&ipu1_di0_disp0 {
> + remote-endpoint = <&display0_in>;
> +};
> +
> +®_lcd0_pwr {
> + status = "disabled";
> +};
> +
> +&usdhc4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usdhc4>;
> + bus-width = <4>;
> + non-removable;
> + no-1-8-v;
> + fsl,wp-controller;
> + status = "okay";
> +};
> +
> +&iomuxc {
> + pinctrl_usdhc4: usdhc4grp {
> + fsl,pins = <
> + MX6QDL_PAD_SD4_CMD__SD4_CMD 0x070b1
> + MX6QDL_PAD_SD4_CLK__SD4_CLK 0x070b1
> + MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x070b1
> + MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x070b1
> + MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x070b1
> + MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x070b1
> + MX6QDL_PAD_NANDF_ALE__SD4_RESET 0x0b0b1
> + >;
> + };
> +};
> diff --git a/arch/arm/boot/dts/imx6dl-tx6u-8033.dts b/arch/arm/boot/dts/imx6dl-tx6u-8033.dts
> new file mode 100644
> index 0000000..4d3204a
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6dl-tx6u-8033.dts
> @@ -0,0 +1,248 @@
> +/*
> + * Copyright 2014-2016 Lothar Wa?mann <LW@KARO-electronics.de>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License
> + * version 2 as published by the Free Software Foundation.
> + *
> + * This file is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +#include "imx6dl.dtsi"
> +#include "imx6qdl-tx6.dtsi"
> +
> +/ {
> + model = "Ka-Ro electronics TX6U-8033 Module";
> + compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl";
> +
> + aliases {
> + display = &display;
> + };
> +
> + backlight: backlight {
> + compatible = "pwm-backlight";
> + pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_lcd0_pwr>;
> + enable-gpios = <&gpio3 29 GPIO_ACTIVE_HIGH>;
> + power-supply = <®_lcd1_pwr>;
> + /*
> + * a poor man's way to create a 1:1 relationship between
> + * the PWM value and the actual duty cycle
> + */
> + brightness-levels = < 0 1 2 3 4 5 6 7 8 9
> + 10 11 12 13 14 15 16 17 18 19
> + 20 21 22 23 24 25 26 27 28 29
> + 30 31 32 33 34 35 36 37 38 39
> + 40 41 42 43 44 45 46 47 48 49
> + 50 51 52 53 54 55 56 57 58 59
> + 60 61 62 63 64 65 66 67 68 69
> + 70 71 72 73 74 75 76 77 78 79
> + 80 81 82 83 84 85 86 87 88 89
> + 90 91 92 93 94 95 96 97 98 99
> + 100>;
> + default-brightness-level = <50>;
> + };
> +
> + display: display at di0 {
> + compatible = "fsl,imx-parallel-display";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_disp0_2>;
> + interface-pix-fmt = "rgb24";
> + status = "okay";
> +
> + port {
> + display0_in: endpoint {
> + remote-endpoint = <&ipu1_di0_disp0>;
> + };
> + };
> +
> + display-timings {
> + native-mode = <&vga>;
> +
> + vga: VGA {
> + clock-frequency = <25200000>;
> + hactive = <640>;
> + vactive = <480>;
> + hback-porch = <48>;
> + hsync-len = <96>;
> + hfront-porch = <16>;
> + vback-porch = <31>;
> + vsync-len = <2>;
> + vfront-porch = <12>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ETV570 {
> + clock-frequency = <25200000>;
> + hactive = <640>;
> + vactive = <480>;
> + hback-porch = <114>;
> + hsync-len = <30>;
> + hfront-porch = <16>;
> + vback-porch = <32>;
> + vsync-len = <3>;
> + vfront-porch = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ET0350 {
> + clock-frequency = <6413760>;
> + hactive = <320>;
> + vactive = <240>;
> + hback-porch = <34>;
> + hsync-len = <34>;
> + hfront-porch = <20>;
> + vback-porch = <15>;
> + vsync-len = <3>;
> + vfront-porch = <4>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ET0430 {
> + clock-frequency = <9009000>;
> + hactive = <480>;
> + vactive = <272>;
> + hback-porch = <2>;
> + hsync-len = <41>;
> + hfront-porch = <2>;
> + vback-porch = <2>;
> + vsync-len = <10>;
> + vfront-porch = <2>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <1>;
> + };
> +
> + ET0500 {
> + clock-frequency = <33264000>;
> + hactive = <800>;
> + vactive = <480>;
> + hback-porch = <88>;
> + hsync-len = <128>;
> + hfront-porch = <40>;
> + vback-porch = <33>;
> + vsync-len = <2>;
> + vfront-porch = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ET0700 { /* same as ET0500 */
> + clock-frequency = <33264000>;
> + hactive = <800>;
> + vactive = <480>;
> + hback-porch = <88>;
> + hsync-len = <128>;
> + hfront-porch = <40>;
> + vback-porch = <33>;
> + vsync-len = <2>;
> + vfront-porch = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ETQ570 {
> + clock-frequency = <6596040>;
> + hactive = <320>;
> + vactive = <240>;
> + hback-porch = <38>;
> + hsync-len = <30>;
> + hfront-porch = <30>;
> + vback-porch = <16>;
> + vsync-len = <3>;
> + vfront-porch = <4>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> + };
> + };
> +};
> +
> +&ds1339 {
> + status = "disabled";
> +};
> +
> +&gpmi {
> + status = "disabled";
> +};
> +
> +&ipu1_di0_disp0 {
> + remote-endpoint = <&display0_in>;
> +};
> +
> +®_lcd0_pwr {
> + status = "disabled";
> +};
> +
> +&usdhc4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usdhc4>;
> + bus-width = <4>;
> + non-removable;
> + no-1-8-v;
> + fsl,wp-controller;
> + status = "okay";
> +};
> +
> +&iomuxc {
> + pinctrl_usdhc4: usdhc4grp {
> + fsl,pins = <
> + MX6QDL_PAD_SD4_CMD__SD4_CMD 0x070b1
> + MX6QDL_PAD_SD4_CLK__SD4_CLK 0x070b1
> + MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x070b1
> + MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x070b1
> + MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x070b1
> + MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x070b1
> + MX6QDL_PAD_NANDF_ALE__SD4_RESET 0x0b0b1
> + >;
> + };
> +};
> diff --git a/arch/arm/boot/dts/imx6q-tx6q-1036.dts b/arch/arm/boot/dts/imx6q-tx6q-1036.dts
> new file mode 100644
> index 0000000..70c478b
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6q-tx6q-1036.dts
> @@ -0,0 +1,252 @@
> +/*
> + * Copyright 2014-2016 Lothar Wa?mann <LW@KARO-electronics.de>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License
> + * version 2 as published by the Free Software Foundation.
> + *
> + * This file is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +#include "imx6q.dtsi"
> +#include "imx6qdl-tx6.dtsi"
> +
> +/ {
> + model = "Ka-Ro electronics TX6Q-1036 Module";
> + compatible = "karo,imx6q-tx6q", "fsl,imx6q";
> +
> + aliases {
> + display = &display;
> + };
> +
> + backlight: backlight {
> + compatible = "pwm-backlight";
> + pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_lcd0_pwr>;
> + enable-gpios = <&gpio3 29 GPIO_ACTIVE_HIGH>;
> + power-supply = <®_lcd1_pwr>;
> + /*
> + * a poor man's way to create a 1:1 relationship between
> + * the PWM value and the actual duty cycle
> + */
> + brightness-levels = < 0 1 2 3 4 5 6 7 8 9
> + 10 11 12 13 14 15 16 17 18 19
> + 20 21 22 23 24 25 26 27 28 29
> + 30 31 32 33 34 35 36 37 38 39
> + 40 41 42 43 44 45 46 47 48 49
> + 50 51 52 53 54 55 56 57 58 59
> + 60 61 62 63 64 65 66 67 68 69
> + 70 71 72 73 74 75 76 77 78 79
> + 80 81 82 83 84 85 86 87 88 89
> + 90 91 92 93 94 95 96 97 98 99
> + 100>;
> + default-brightness-level = <50>;
> + };
> +
> + display: display at di0 {
> + compatible = "fsl,imx-parallel-display";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_disp0_2>;
> + interface-pix-fmt = "rgb24";
> + status = "okay";
> +
> + port {
> + display0_in: endpoint {
> + remote-endpoint = <&ipu1_di0_disp0>;
> + };
> + };
> +
> + display-timings {
> + native-mode = <&vga>;
> +
> + vga: VGA {
> + clock-frequency = <25200000>;
> + hactive = <640>;
> + vactive = <480>;
> + hback-porch = <48>;
> + hsync-len = <96>;
> + hfront-porch = <16>;
> + vback-porch = <31>;
> + vsync-len = <2>;
> + vfront-porch = <12>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ETV570 {
> + clock-frequency = <25200000>;
> + hactive = <640>;
> + vactive = <480>;
> + hback-porch = <114>;
> + hsync-len = <30>;
> + hfront-porch = <16>;
> + vback-porch = <32>;
> + vsync-len = <3>;
> + vfront-porch = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ET0350 {
> + clock-frequency = <6413760>;
> + hactive = <320>;
> + vactive = <240>;
> + hback-porch = <34>;
> + hsync-len = <34>;
> + hfront-porch = <20>;
> + vback-porch = <15>;
> + vsync-len = <3>;
> + vfront-porch = <4>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ET0430 {
> + clock-frequency = <9009000>;
> + hactive = <480>;
> + vactive = <272>;
> + hback-porch = <2>;
> + hsync-len = <41>;
> + hfront-porch = <2>;
> + vback-porch = <2>;
> + vsync-len = <10>;
> + vfront-porch = <2>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <1>;
> + };
> +
> + ET0500 {
> + clock-frequency = <33264000>;
> + hactive = <800>;
> + vactive = <480>;
> + hback-porch = <88>;
> + hsync-len = <128>;
> + hfront-porch = <40>;
> + vback-porch = <33>;
> + vsync-len = <2>;
> + vfront-porch = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ET0700 { /* same as ET0500 */
> + clock-frequency = <33264000>;
> + hactive = <800>;
> + vactive = <480>;
> + hback-porch = <88>;
> + hsync-len = <128>;
> + hfront-porch = <40>;
> + vback-porch = <33>;
> + vsync-len = <2>;
> + vfront-porch = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ETQ570 {
> + clock-frequency = <6596040>;
> + hactive = <320>;
> + vactive = <240>;
> + hback-porch = <38>;
> + hsync-len = <30>;
> + hfront-porch = <30>;
> + vback-porch = <16>;
> + vsync-len = <3>;
> + vfront-porch = <4>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> + };
> + };
> +};
> +
> +&ds1339 {
> + status = "disabled";
> +};
> +
> +&gpmi {
> + status = "disabled";
> +};
> +
> +&ipu1_di0_disp0 {
> + remote-endpoint = <&display0_in>;
> +};
> +
> +&ipu2 {
> + status = "disabled";
> +};
> +
> +®_lcd0_pwr {
> + status = "disabled";
> +};
> +
> +&usdhc4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usdhc4>;
> + bus-width = <4>;
> + non-removable;
> + no-1-8-v;
> + fsl,wp-controller;
> + status = "okay";
> +};
> +
> +&iomuxc {
> + pinctrl_usdhc4: usdhc4grp {
> + fsl,pins = <
> + MX6QDL_PAD_SD4_CMD__SD4_CMD 0x070b1
> + MX6QDL_PAD_SD4_CLK__SD4_CLK 0x070b1
> + MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x070b1
> + MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x070b1
> + MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x070b1
> + MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x070b1
> + MX6QDL_PAD_NANDF_ALE__SD4_RESET 0x0b0b1
> + >;
> + };
> +};
> --
> 2.1.4
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
WARNING: multiple messages have this Message-ID (diff)
From: Shawn Guo <shawnguo@kernel.org>
To: "Lothar Waßmann" <LW@KARO-electronics.de>
Cc: Dan Williams <dan.j.williams@intel.com>,
Ian Campbell <ijc+devicetree@hellion.org.uk>,
Kumar Gala <galak@codeaurora.org>,
Mark Rutland <mark.rutland@arm.com>,
Pawel Moll <pawel.moll@arm.com>, Rob Herring <robh+dt@kernel.org>,
Russell King <linux@arm.linux.org.uk>,
Sascha Hauer <kernel@pengutronix.de>,
Vinod Koul <vinod.koul@intel.com>,
devicetree@vger.kernel.org, dmaengine@vger.kernel.org,
linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org
Subject: Re: [PATCHv2 7/8] ARM: dts: imx6: add support for more Ka-Ro electronics modules
Date: Thu, 31 Mar 2016 14:10:23 +0800 [thread overview]
Message-ID: <20160331061023.GO28207@tiger> (raw)
In-Reply-To: <1457424244-14549-8-git-send-email-LW@KARO-electronics.de>
On Tue, Mar 08, 2016 at 09:04:03AM +0100, Lothar Waßmann wrote:
> Add support for the following i.MX6 based modules from Ka-Ro
> electronics GmbH:
> TX6S-8034:
> Processor Freescale i.MX 6 Solo, 800MHz
> RAM 256MiB DDR3 SDRAM
> ROM 128MiB NAND Flash
> Power supply Single 3.1V to 5.5V
> Size 31mm SO-DIMM
> Temp. Range industrial grade (-40°C/-25°C to 105°C Tj)
>
> TX6S-8035:
> Processor Freescale i.MX 6 Solo, 800MHz
> RAM 512MiB DDR3 SDRAM
> ROM 4GiB eMMC
> Power supply Single 3.1V to 5.5V
> Size 31mm SO-DIMM
> Temp. Range industrial grade (-40°C/-25°C to 105°C Tj)
>
> TX6U-8033:
> Processor Freescale i.MX 6 Dual Lite, 800MHz
> RAM 1GiB DDR3 SDRAM
> ROM 4GiB eMMC
> Power supply Single 3.1V to 5.5V
> Size 31mm SO-DIMM
> Temp. Range industrial grade (-40°C/-25°C to 105°C Tj)
>
> TX6Q-1036:
> Processor Freescale i.MX 6Quad, 1GHz
> RAM 1GB DDR3 SDRAM 64-bit
> ROM 8GiB eMMC
> Power supply Single 3.1V to 5.5V
> Size 31mm SO-DIMM
> Temp. Range Extended Consumer Grade (-20°C to 105°C Tj)
>
> Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
> ---
> arch/arm/boot/dts/Makefile | 4 +
> arch/arm/boot/dts/imx6dl-tx6s-8034.dts | 249 ++++++++++++++++++++++++++++
> arch/arm/boot/dts/imx6dl-tx6s-8035.dts | 246 +++++++++++++++++++++++++++
> arch/arm/boot/dts/imx6dl-tx6u-8033.dts | 248 +++++++++++++++++++++++++++
> arch/arm/boot/dts/imx6q-tx6q-1036.dts | 295 +++++++++++++++++++++++++++++++++
> 5 files changed, 1042 insertions(+)
> create mode 100644 arch/arm/boot/dts/imx6dl-tx6s-8034.dts
> create mode 100644 arch/arm/boot/dts/imx6dl-tx6s-8035.dts
> create mode 100644 arch/arm/boot/dts/imx6dl-tx6u-8033.dts
> create mode 100644 arch/arm/boot/dts/imx6q-tx6q-1036.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 072294f..71b5cd3 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -320,6 +320,9 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
> imx6dl-sabrelite.dtb \
> imx6dl-sabresd.dtb \
> imx6dl-tx6dl-comtft.dtb \
> + imx6dl-tx6s-8034.dtb \
> + imx6dl-tx6s-8035.dtb \
> + imx6dl-tx6u-8033.dtb \
imx6dl-tx6u-8033.dtb should go after imx6dl-tx6u-801x.dtb?
Shawn
> imx6dl-tx6u-801x.dtb \
> imx6dl-tx6u-811x.dtb \
> imx6dl-udoo.dtb \
> @@ -360,6 +363,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
> imx6q-tx6q-1010-comtft.dtb \
> imx6q-tx6q-1020.dtb \
> imx6q-tx6q-1020-comtft.dtb \
> + imx6q-tx6q-1036.dtb \
> imx6q-tx6q-1110.dtb \
> imx6q-udoo.dtb \
> imx6q-wandboard.dtb \
> diff --git a/arch/arm/boot/dts/imx6dl-tx6s-8034.dts b/arch/arm/boot/dts/imx6dl-tx6s-8034.dts
> new file mode 100644
> index 0000000..0d3df6e
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6dl-tx6s-8034.dts
> @@ -0,0 +1,237 @@
> +/*
> + * Copyright 2015-2016 Lothar Waßmann <LW@KARO-electronics.de>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License
> + * version 2 as published by the Free Software Foundation.
> + *
> + * This file is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +#include "imx6dl.dtsi"
> +#include "imx6qdl-tx6.dtsi"
> +
> +/ {
> + model = "Ka-Ro electronics TX6S-8034 Module";
> + compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl";
> +
> + aliases {
> + display = &display;
> + ipu1 = &ipu1;
> + };
> +
> + cpus {
> + /delete-node/ cpu@1;
> + };
> +
> + backlight: backlight {
> + compatible = "pwm-backlight";
> + pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_lcd0_pwr>;
> + enable-gpios = <&gpio3 29 GPIO_ACTIVE_HIGH>;
> + power-supply = <®_lcd1_pwr>;
> + /*
> + * a poor man's way to create a 1:1 relationship between
> + * the PWM value and the actual duty cycle
> + */
> + brightness-levels = < 0 1 2 3 4 5 6 7 8 9
> + 10 11 12 13 14 15 16 17 18 19
> + 20 21 22 23 24 25 26 27 28 29
> + 30 31 32 33 34 35 36 37 38 39
> + 40 41 42 43 44 45 46 47 48 49
> + 50 51 52 53 54 55 56 57 58 59
> + 60 61 62 63 64 65 66 67 68 69
> + 70 71 72 73 74 75 76 77 78 79
> + 80 81 82 83 84 85 86 87 88 89
> + 90 91 92 93 94 95 96 97 98 99
> + 100>;
> + default-brightness-level = <50>;
> + };
> +
> + display: display@di0 {
> + compatible = "fsl,imx-parallel-display";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_disp0_2>;
> + interface-pix-fmt = "rgb24";
> + status = "okay";
> +
> + port {
> + display0_in: endpoint {
> + remote-endpoint = <&ipu1_di0_disp0>;
> + };
> + };
> +
> + display-timings {
> + native-mode = <&vga>;
> +
> + vga: VGA {
> + clock-frequency = <25200000>;
> + hactive = <640>;
> + vactive = <480>;
> + hback-porch = <48>;
> + hsync-len = <96>;
> + hfront-porch = <16>;
> + vback-porch = <31>;
> + vsync-len = <2>;
> + vfront-porch = <12>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ETV570 {
> + clock-frequency = <25200000>;
> + hactive = <640>;
> + vactive = <480>;
> + hback-porch = <114>;
> + hsync-len = <30>;
> + hfront-porch = <16>;
> + vback-porch = <32>;
> + vsync-len = <3>;
> + vfront-porch = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ET0350 {
> + clock-frequency = <6413760>;
> + hactive = <320>;
> + vactive = <240>;
> + hback-porch = <34>;
> + hsync-len = <34>;
> + hfront-porch = <20>;
> + vback-porch = <15>;
> + vsync-len = <3>;
> + vfront-porch = <4>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ET0430 {
> + clock-frequency = <9009000>;
> + hactive = <480>;
> + vactive = <272>;
> + hback-porch = <2>;
> + hsync-len = <41>;
> + hfront-porch = <2>;
> + vback-porch = <2>;
> + vsync-len = <10>;
> + vfront-porch = <2>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <1>;
> + };
> +
> + ET0500 {
> + clock-frequency = <33264000>;
> + hactive = <800>;
> + vactive = <480>;
> + hback-porch = <88>;
> + hsync-len = <128>;
> + hfront-porch = <40>;
> + vback-porch = <33>;
> + vsync-len = <2>;
> + vfront-porch = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ET0700 { /* same as ET0500 */
> + clock-frequency = <33264000>;
> + hactive = <800>;
> + vactive = <480>;
> + hback-porch = <88>;
> + hsync-len = <128>;
> + hfront-porch = <40>;
> + vback-porch = <33>;
> + vsync-len = <2>;
> + vfront-porch = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ETQ570 {
> + clock-frequency = <6596040>;
> + hactive = <320>;
> + vactive = <240>;
> + hback-porch = <38>;
> + hsync-len = <30>;
> + hfront-porch = <30>;
> + vback-porch = <16>;
> + vsync-len = <3>;
> + vfront-porch = <4>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> + };
> + };
> +};
> +
> +&ds1339 {
> + status = "disabled";
> +};
> +
> +&pinctrl_usdhc1 {
> + fsl,pins = <
> + MX6QDL_PAD_SD1_CMD__SD1_CMD 0x070b1
> + MX6QDL_PAD_SD1_CLK__SD1_CLK 0x07099
> + MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x070b1
> + MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x070b1
> + MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x070b1
> + MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x070b1
> + MX6QDL_PAD_SD3_CMD__GPIO7_IO02 0x170b0 /* SD1 CD */
> + >;
> +};
> +
> +&ipu1_di0_disp0 {
> + remote-endpoint = <&display0_in>;
> +};
> +
> +®_lcd0_pwr {
> + status = "disabled";
> +};
> diff --git a/arch/arm/boot/dts/imx6dl-tx6s-8035.dts b/arch/arm/boot/dts/imx6dl-tx6s-8035.dts
> new file mode 100644
> index 0000000..2f9efdb
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6dl-tx6s-8035.dts
> @@ -0,0 +1,253 @@
> +/*
> + * Copyright 2015-2016 Lothar Waßmann <LW@KARO-electronics.de>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License
> + * version 2 as published by the Free Software Foundation.
> + *
> + * This file is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +#include "imx6dl.dtsi"
> +#include "imx6qdl-tx6.dtsi"
> +
> +/ {
> + model = "Ka-Ro electronics TX6S-8035 Module";
> + compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl";
> +
> + aliases {
> + display = &display;
> + ipu1 = &ipu1;
> + };
> +
> + cpus {
> + /delete-node/ cpu@1;
> + };
> +
> + backlight: backlight {
> + compatible = "pwm-backlight";
> + pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_lcd0_pwr>;
> + enable-gpios = <&gpio3 29 GPIO_ACTIVE_HIGH>;
> + power-supply = <®_lcd1_pwr>;
> + /*
> + * a poor man's way to create a 1:1 relationship between
> + * the PWM value and the actual duty cycle
> + */
> + brightness-levels = < 0 1 2 3 4 5 6 7 8 9
> + 10 11 12 13 14 15 16 17 18 19
> + 20 21 22 23 24 25 26 27 28 29
> + 30 31 32 33 34 35 36 37 38 39
> + 40 41 42 43 44 45 46 47 48 49
> + 50 51 52 53 54 55 56 57 58 59
> + 60 61 62 63 64 65 66 67 68 69
> + 70 71 72 73 74 75 76 77 78 79
> + 80 81 82 83 84 85 86 87 88 89
> + 90 91 92 93 94 95 96 97 98 99
> + 100>;
> + default-brightness-level = <50>;
> + };
> +
> + display: display@di0 {
> + compatible = "fsl,imx-parallel-display";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_disp0_2>;
> + interface-pix-fmt = "rgb24";
> + status = "okay";
> +
> + port {
> + display0_in: endpoint {
> + remote-endpoint = <&ipu1_di0_disp0>;
> + };
> + };
> +
> + display-timings {
> + native-mode = <&vga>;
> +
> + vga: VGA {
> + clock-frequency = <25200000>;
> + hactive = <640>;
> + vactive = <480>;
> + hback-porch = <48>;
> + hsync-len = <96>;
> + hfront-porch = <16>;
> + vback-porch = <31>;
> + vsync-len = <2>;
> + vfront-porch = <12>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ETV570 {
> + clock-frequency = <25200000>;
> + hactive = <640>;
> + vactive = <480>;
> + hback-porch = <114>;
> + hsync-len = <30>;
> + hfront-porch = <16>;
> + vback-porch = <32>;
> + vsync-len = <3>;
> + vfront-porch = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ET0350 {
> + clock-frequency = <6413760>;
> + hactive = <320>;
> + vactive = <240>;
> + hback-porch = <34>;
> + hsync-len = <34>;
> + hfront-porch = <20>;
> + vback-porch = <15>;
> + vsync-len = <3>;
> + vfront-porch = <4>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ET0430 {
> + clock-frequency = <9009000>;
> + hactive = <480>;
> + vactive = <272>;
> + hback-porch = <2>;
> + hsync-len = <41>;
> + hfront-porch = <2>;
> + vback-porch = <2>;
> + vsync-len = <10>;
> + vfront-porch = <2>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <1>;
> + };
> +
> + ET0500 {
> + clock-frequency = <33264000>;
> + hactive = <800>;
> + vactive = <480>;
> + hback-porch = <88>;
> + hsync-len = <128>;
> + hfront-porch = <40>;
> + vback-porch = <33>;
> + vsync-len = <2>;
> + vfront-porch = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ET0700 { /* same as ET0500 */
> + clock-frequency = <33264000>;
> + hactive = <800>;
> + vactive = <480>;
> + hback-porch = <88>;
> + hsync-len = <128>;
> + hfront-porch = <40>;
> + vback-porch = <33>;
> + vsync-len = <2>;
> + vfront-porch = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ETQ570 {
> + clock-frequency = <6596040>;
> + hactive = <320>;
> + vactive = <240>;
> + hback-porch = <38>;
> + hsync-len = <30>;
> + hfront-porch = <30>;
> + vback-porch = <16>;
> + vsync-len = <3>;
> + vfront-porch = <4>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> + };
> + };
> +};
> +
> +&ds1339 {
> + status = "disabled";
> +};
> +
> +&gpmi {
> + status = "disabled";
> +};
> +
> +&ipu1_di0_disp0 {
> + remote-endpoint = <&display0_in>;
> +};
> +
> +®_lcd0_pwr {
> + status = "disabled";
> +};
> +
> +&usdhc4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usdhc4>;
> + bus-width = <4>;
> + non-removable;
> + no-1-8-v;
> + fsl,wp-controller;
> + status = "okay";
> +};
> +
> +&iomuxc {
> + pinctrl_usdhc4: usdhc4grp {
> + fsl,pins = <
> + MX6QDL_PAD_SD4_CMD__SD4_CMD 0x070b1
> + MX6QDL_PAD_SD4_CLK__SD4_CLK 0x070b1
> + MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x070b1
> + MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x070b1
> + MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x070b1
> + MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x070b1
> + MX6QDL_PAD_NANDF_ALE__SD4_RESET 0x0b0b1
> + >;
> + };
> +};
> diff --git a/arch/arm/boot/dts/imx6dl-tx6u-8033.dts b/arch/arm/boot/dts/imx6dl-tx6u-8033.dts
> new file mode 100644
> index 0000000..4d3204a
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6dl-tx6u-8033.dts
> @@ -0,0 +1,248 @@
> +/*
> + * Copyright 2014-2016 Lothar Waßmann <LW@KARO-electronics.de>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License
> + * version 2 as published by the Free Software Foundation.
> + *
> + * This file is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +#include "imx6dl.dtsi"
> +#include "imx6qdl-tx6.dtsi"
> +
> +/ {
> + model = "Ka-Ro electronics TX6U-8033 Module";
> + compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl";
> +
> + aliases {
> + display = &display;
> + };
> +
> + backlight: backlight {
> + compatible = "pwm-backlight";
> + pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_lcd0_pwr>;
> + enable-gpios = <&gpio3 29 GPIO_ACTIVE_HIGH>;
> + power-supply = <®_lcd1_pwr>;
> + /*
> + * a poor man's way to create a 1:1 relationship between
> + * the PWM value and the actual duty cycle
> + */
> + brightness-levels = < 0 1 2 3 4 5 6 7 8 9
> + 10 11 12 13 14 15 16 17 18 19
> + 20 21 22 23 24 25 26 27 28 29
> + 30 31 32 33 34 35 36 37 38 39
> + 40 41 42 43 44 45 46 47 48 49
> + 50 51 52 53 54 55 56 57 58 59
> + 60 61 62 63 64 65 66 67 68 69
> + 70 71 72 73 74 75 76 77 78 79
> + 80 81 82 83 84 85 86 87 88 89
> + 90 91 92 93 94 95 96 97 98 99
> + 100>;
> + default-brightness-level = <50>;
> + };
> +
> + display: display@di0 {
> + compatible = "fsl,imx-parallel-display";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_disp0_2>;
> + interface-pix-fmt = "rgb24";
> + status = "okay";
> +
> + port {
> + display0_in: endpoint {
> + remote-endpoint = <&ipu1_di0_disp0>;
> + };
> + };
> +
> + display-timings {
> + native-mode = <&vga>;
> +
> + vga: VGA {
> + clock-frequency = <25200000>;
> + hactive = <640>;
> + vactive = <480>;
> + hback-porch = <48>;
> + hsync-len = <96>;
> + hfront-porch = <16>;
> + vback-porch = <31>;
> + vsync-len = <2>;
> + vfront-porch = <12>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ETV570 {
> + clock-frequency = <25200000>;
> + hactive = <640>;
> + vactive = <480>;
> + hback-porch = <114>;
> + hsync-len = <30>;
> + hfront-porch = <16>;
> + vback-porch = <32>;
> + vsync-len = <3>;
> + vfront-porch = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ET0350 {
> + clock-frequency = <6413760>;
> + hactive = <320>;
> + vactive = <240>;
> + hback-porch = <34>;
> + hsync-len = <34>;
> + hfront-porch = <20>;
> + vback-porch = <15>;
> + vsync-len = <3>;
> + vfront-porch = <4>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ET0430 {
> + clock-frequency = <9009000>;
> + hactive = <480>;
> + vactive = <272>;
> + hback-porch = <2>;
> + hsync-len = <41>;
> + hfront-porch = <2>;
> + vback-porch = <2>;
> + vsync-len = <10>;
> + vfront-porch = <2>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <1>;
> + };
> +
> + ET0500 {
> + clock-frequency = <33264000>;
> + hactive = <800>;
> + vactive = <480>;
> + hback-porch = <88>;
> + hsync-len = <128>;
> + hfront-porch = <40>;
> + vback-porch = <33>;
> + vsync-len = <2>;
> + vfront-porch = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ET0700 { /* same as ET0500 */
> + clock-frequency = <33264000>;
> + hactive = <800>;
> + vactive = <480>;
> + hback-porch = <88>;
> + hsync-len = <128>;
> + hfront-porch = <40>;
> + vback-porch = <33>;
> + vsync-len = <2>;
> + vfront-porch = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ETQ570 {
> + clock-frequency = <6596040>;
> + hactive = <320>;
> + vactive = <240>;
> + hback-porch = <38>;
> + hsync-len = <30>;
> + hfront-porch = <30>;
> + vback-porch = <16>;
> + vsync-len = <3>;
> + vfront-porch = <4>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> + };
> + };
> +};
> +
> +&ds1339 {
> + status = "disabled";
> +};
> +
> +&gpmi {
> + status = "disabled";
> +};
> +
> +&ipu1_di0_disp0 {
> + remote-endpoint = <&display0_in>;
> +};
> +
> +®_lcd0_pwr {
> + status = "disabled";
> +};
> +
> +&usdhc4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usdhc4>;
> + bus-width = <4>;
> + non-removable;
> + no-1-8-v;
> + fsl,wp-controller;
> + status = "okay";
> +};
> +
> +&iomuxc {
> + pinctrl_usdhc4: usdhc4grp {
> + fsl,pins = <
> + MX6QDL_PAD_SD4_CMD__SD4_CMD 0x070b1
> + MX6QDL_PAD_SD4_CLK__SD4_CLK 0x070b1
> + MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x070b1
> + MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x070b1
> + MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x070b1
> + MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x070b1
> + MX6QDL_PAD_NANDF_ALE__SD4_RESET 0x0b0b1
> + >;
> + };
> +};
> diff --git a/arch/arm/boot/dts/imx6q-tx6q-1036.dts b/arch/arm/boot/dts/imx6q-tx6q-1036.dts
> new file mode 100644
> index 0000000..70c478b
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6q-tx6q-1036.dts
> @@ -0,0 +1,252 @@
> +/*
> + * Copyright 2014-2016 Lothar Waßmann <LW@KARO-electronics.de>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License
> + * version 2 as published by the Free Software Foundation.
> + *
> + * This file is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +#include "imx6q.dtsi"
> +#include "imx6qdl-tx6.dtsi"
> +
> +/ {
> + model = "Ka-Ro electronics TX6Q-1036 Module";
> + compatible = "karo,imx6q-tx6q", "fsl,imx6q";
> +
> + aliases {
> + display = &display;
> + };
> +
> + backlight: backlight {
> + compatible = "pwm-backlight";
> + pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_lcd0_pwr>;
> + enable-gpios = <&gpio3 29 GPIO_ACTIVE_HIGH>;
> + power-supply = <®_lcd1_pwr>;
> + /*
> + * a poor man's way to create a 1:1 relationship between
> + * the PWM value and the actual duty cycle
> + */
> + brightness-levels = < 0 1 2 3 4 5 6 7 8 9
> + 10 11 12 13 14 15 16 17 18 19
> + 20 21 22 23 24 25 26 27 28 29
> + 30 31 32 33 34 35 36 37 38 39
> + 40 41 42 43 44 45 46 47 48 49
> + 50 51 52 53 54 55 56 57 58 59
> + 60 61 62 63 64 65 66 67 68 69
> + 70 71 72 73 74 75 76 77 78 79
> + 80 81 82 83 84 85 86 87 88 89
> + 90 91 92 93 94 95 96 97 98 99
> + 100>;
> + default-brightness-level = <50>;
> + };
> +
> + display: display@di0 {
> + compatible = "fsl,imx-parallel-display";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_disp0_2>;
> + interface-pix-fmt = "rgb24";
> + status = "okay";
> +
> + port {
> + display0_in: endpoint {
> + remote-endpoint = <&ipu1_di0_disp0>;
> + };
> + };
> +
> + display-timings {
> + native-mode = <&vga>;
> +
> + vga: VGA {
> + clock-frequency = <25200000>;
> + hactive = <640>;
> + vactive = <480>;
> + hback-porch = <48>;
> + hsync-len = <96>;
> + hfront-porch = <16>;
> + vback-porch = <31>;
> + vsync-len = <2>;
> + vfront-porch = <12>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ETV570 {
> + clock-frequency = <25200000>;
> + hactive = <640>;
> + vactive = <480>;
> + hback-porch = <114>;
> + hsync-len = <30>;
> + hfront-porch = <16>;
> + vback-porch = <32>;
> + vsync-len = <3>;
> + vfront-porch = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ET0350 {
> + clock-frequency = <6413760>;
> + hactive = <320>;
> + vactive = <240>;
> + hback-porch = <34>;
> + hsync-len = <34>;
> + hfront-porch = <20>;
> + vback-porch = <15>;
> + vsync-len = <3>;
> + vfront-porch = <4>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ET0430 {
> + clock-frequency = <9009000>;
> + hactive = <480>;
> + vactive = <272>;
> + hback-porch = <2>;
> + hsync-len = <41>;
> + hfront-porch = <2>;
> + vback-porch = <2>;
> + vsync-len = <10>;
> + vfront-porch = <2>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <1>;
> + };
> +
> + ET0500 {
> + clock-frequency = <33264000>;
> + hactive = <800>;
> + vactive = <480>;
> + hback-porch = <88>;
> + hsync-len = <128>;
> + hfront-porch = <40>;
> + vback-porch = <33>;
> + vsync-len = <2>;
> + vfront-porch = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ET0700 { /* same as ET0500 */
> + clock-frequency = <33264000>;
> + hactive = <800>;
> + vactive = <480>;
> + hback-porch = <88>;
> + hsync-len = <128>;
> + hfront-porch = <40>;
> + vback-porch = <33>;
> + vsync-len = <2>;
> + vfront-porch = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ETQ570 {
> + clock-frequency = <6596040>;
> + hactive = <320>;
> + vactive = <240>;
> + hback-porch = <38>;
> + hsync-len = <30>;
> + hfront-porch = <30>;
> + vback-porch = <16>;
> + vsync-len = <3>;
> + vfront-porch = <4>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> + };
> + };
> +};
> +
> +&ds1339 {
> + status = "disabled";
> +};
> +
> +&gpmi {
> + status = "disabled";
> +};
> +
> +&ipu1_di0_disp0 {
> + remote-endpoint = <&display0_in>;
> +};
> +
> +&ipu2 {
> + status = "disabled";
> +};
> +
> +®_lcd0_pwr {
> + status = "disabled";
> +};
> +
> +&usdhc4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usdhc4>;
> + bus-width = <4>;
> + non-removable;
> + no-1-8-v;
> + fsl,wp-controller;
> + status = "okay";
> +};
> +
> +&iomuxc {
> + pinctrl_usdhc4: usdhc4grp {
> + fsl,pins = <
> + MX6QDL_PAD_SD4_CMD__SD4_CMD 0x070b1
> + MX6QDL_PAD_SD4_CLK__SD4_CLK 0x070b1
> + MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x070b1
> + MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x070b1
> + MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x070b1
> + MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x070b1
> + MX6QDL_PAD_NANDF_ALE__SD4_RESET 0x0b0b1
> + >;
> + };
> +};
> --
> 2.1.4
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2016-03-31 6:10 UTC|newest]
Thread overview: 54+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-03-08 8:03 [PATCHv2 0/8] ARM: dts: update Ka-Ro i.MX6 module support Lothar Waßmann
2016-03-08 8:03 ` Lothar Waßmann
2016-03-08 8:03 ` Lothar Waßmann
2016-03-08 8:03 ` [PATCHv2 1/8] ARM: dts: imx6-tx6: Relicense the Ka-Ro DT files under GPLv2/X11 Lothar Waßmann
2016-03-08 8:03 ` Lothar Waßmann
2016-03-08 8:03 ` Lothar Waßmann
2016-03-08 8:03 ` [PATCHv2 2/8] ARM: dts: imx6-tx6: cleanup; no functional change Lothar Waßmann
2016-03-08 8:03 ` Lothar Waßmann
2016-03-08 8:03 ` Lothar Waßmann
2016-03-08 8:03 ` [PATCHv2 3/8] ARM: dts: imx6-tx6: remove regulator bus Lothar Waßmann
2016-03-08 8:03 ` Lothar Waßmann
2016-03-08 8:03 ` Lothar Waßmann
2016-03-31 6:00 ` Shawn Guo
2016-03-31 6:00 ` Shawn Guo
2016-03-31 6:00 ` Shawn Guo
2016-03-08 8:04 ` [PATCHv2 4/8] ARM: dts: imx6-tx6: disable the spi node by default Lothar Waßmann
2016-03-08 8:04 ` Lothar Waßmann
2016-03-08 8:04 ` Lothar Waßmann
2016-03-08 8:04 ` [PATCHv2 5/8] ARM: dts: imx6-tx6: remove container node around pinctrl nodes Lothar Waßmann
2016-03-08 8:04 ` Lothar Waßmann
2016-03-08 8:04 ` [PATCHv2 6/8] ARM: dts: imx6qdl-tx6: add mdio node for ethernet phy Lothar Waßmann
2016-03-08 8:04 ` Lothar Waßmann
2016-03-08 8:04 ` [PATCHv2 7/8] ARM: dts: imx6: add support for more Ka-Ro electronics modules Lothar Waßmann
2016-03-08 8:04 ` Lothar Waßmann
2016-03-08 8:04 ` Lothar Waßmann
2016-03-31 6:10 ` Shawn Guo [this message]
2016-03-31 6:10 ` Shawn Guo
2016-03-31 6:29 ` Lothar Waßmann
2016-03-31 6:29 ` Lothar Waßmann
2016-03-31 7:47 ` Shawn Guo
2016-03-31 7:47 ` Shawn Guo
2016-03-08 8:04 ` [PATCHv2 8/8] ARM: dts: imx6: add support for the Ka-Ro electronics 'MB7' baseboard Lothar Waßmann
2016-03-08 8:04 ` Lothar Waßmann
2016-03-08 8:04 ` Lothar Waßmann
2016-03-31 6:14 ` [PATCHv2 0/8] ARM: dts: update Ka-Ro i.MX6 module support Shawn Guo
2016-03-31 6:14 ` Shawn Guo
2016-03-31 6:14 ` Shawn Guo
2016-03-31 12:33 ` [PATCHv3 0/5] " Lothar Waßmann
2016-03-31 12:33 ` Lothar Waßmann
2016-03-31 12:33 ` [PATCHv3 1/5] ARM: dts: imx6-tx6: remove regulator bus Lothar Waßmann
2016-03-31 12:33 ` Lothar Waßmann
2016-03-31 12:33 ` [PATCHv3 2/5] ARM: dts: imx6-tx6: remove LED pinctrl setting from hoggrp Lothar Waßmann
2016-03-31 12:33 ` Lothar Waßmann
2016-03-31 12:33 ` Lothar Waßmann
2016-03-31 12:33 ` [PATCHv3 3/5] ARM: dts: imx6-tx6: enable support for rtscts on UARTs Lothar Waßmann
2016-03-31 12:33 ` Lothar Waßmann
2016-03-31 12:33 ` [PATCHv3 4/5] ARM: dts: imx6: add support for more Ka-Ro electronics modules Lothar Waßmann
2016-03-31 12:33 ` Lothar Waßmann
2016-03-31 12:33 ` Lothar Waßmann
2016-03-31 12:33 ` [PATCHv3 5/5] ARM: dts: imx6: add support for the Ka-Ro electronics 'MB7' baseboard Lothar Waßmann
2016-03-31 12:33 ` Lothar Waßmann
2016-04-11 13:57 ` [PATCHv3 0/5] ARM: dts: update Ka-Ro i.MX6 module support Shawn Guo
2016-04-11 13:57 ` Shawn Guo
2016-04-11 13:57 ` Shawn Guo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20160331061023.GO28207@tiger \
--to=shawnguo@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.