[PATCH v3] Axi-usb: Add support for 64-bit addressing.

[robh@kernel.org (Rob Herring)]

On Tue, May 24, 2016 at 11:47:31AM +0000, Nava kishore Manne wrote:
> 
> 
> > -----Original Message-----
> > From: Arnd Bergmann [mailto:arnd at arndb.de]
> > Sent: Tuesday, May 24, 2016 2:21 PM
> > To: Nava kishore Manne <navam@xilinx.com>
> > Cc: robh+dt at kernel.org; pawel.moll at arm.com; mark.rutland at arm.com;
> > ijc+devicetree at hellion.org.uk; galak at codeaurora.org; Michal Simek
> > <michals@xilinx.com>; Soren Brinkmann <sorenb@xilinx.com>;
> > balbi at ti.com; gregkh at linuxfoundation.org; Hyun Kwon
> > <hyunk@xilinx.com>; Nava kishore Manne <navam@xilinx.com>; Radhey
> > Shyam Pandey <radheys@xilinx.com>; devicetree at vger.kernel.org; linux-
> > arm-kernel at lists.infradead.org; linux-kernel at vger.kernel.org
> > Subject: Re: [PATCH v3] Axi-usb: Add support for 64-bit addressing.
> > 
> > On Tuesday, May 24, 2016 10:51:08 AM CEST Nava kishore Manne wrote:
> > > diff --git a/Documentation/devicetree/bindings/usb/udc-xilinx.txt
> > > b/Documentation/devicetree/bindings/usb/udc-xilinx.txt
> > > index 47b4e39..09df757 100644
> > > --- a/Documentation/devicetree/bindings/usb/udc-xilinx.txt
> > > +++ b/Documentation/devicetree/bindings/usb/udc-xilinx.txt
> > > @@ -1,18 +1,23 @@
> > >  Xilinx USB2 device controller
> > >
> > >  Required properties:
> > > -- compatible		: Should be "xlnx,usb2-device-4.00.a"
> > > +- compatible		: Should be "xlnx,usb2-device-4.00.a" or
> > > +			  "xlnx,usb2-device-5.00"
> > >  - reg			: Physical base address and size of the USB2
> > >  			  device registers map.
> > >  - interrupts		: Should contain single irq line of USB2 device
> > >  			  controller
> > >  - xlnx,has-builtin-dma	: if DMA is included
> > > +- dma-ranges		: Should be as the following
> > > +			  <child-bus-address, parent-bus-address, length>
> > 
> > A USB host should not have any children that are DMA capable, I think, so
> > this property doesn't make sense here. It should be part of the parent bus.
> > 
> Will send next version (v4) by removing this property from the DT.
> 
> > > +- xlnx,addrwidth	: Should be the dma addressing size in bits(ex: 64
> > bits)
> > 
> > I'm still unconvinced about the property definition here. What are the
> > possible options for the IP block? I don't think I ever saw a reply from you to
> > my earlier questions.
> > 
> 
> Sorry Let me clearly explain
> 
> From the IP version 5.0 onwards The IP support both 32-bit and 64-bit addressing.
> But the older version of the IP's supports only 32-bit addressing.
> 
> This addrwidth property differentiates the address width for the new IP (I mean 5.0 version on wards)
> For older IP it will be always 32-bit.

Then I think you should have a simple boolean property for 64-bit 
configuration.