[linux-sunxi] Re: [PATCH] ARM: dts: sun7i: Add dts file for Bananapi M1 Plus board

[maxime.ripard@free-electrons.com (Maxime Ripard)]

Hi,

On Wed, Jun 01, 2016 at 10:40:18AM +0800, luoyi wrote:
> This is the new version of the patch.  and I think maybe every board
> should have their own dtb files. and we can you some cpp  macro tricks
> to merge their coressponding dts file.

Please submit it as a new patch with send-email, with the version
(using the -v option) and a log of your changes.

> 
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index e06a5ab..fde407f 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -685,6 +685,7 @@ dtb-$(CONFIG_MACH_SUN6I) += \
>      sun6i-a31s-yones-toptech-bs1078-v2.dtb
>  dtb-$(CONFIG_MACH_SUN7I) += \
>      sun7i-a20-bananapi.dtb \
> +    sun7i-a20-bananapi-m1-plus.dtb \
>      sun7i-a20-bananapro.dtb \
>      sun7i-a20-cubieboard2.dtb \
>      sun7i-a20-cubietruck.dtb \
> diff --git a/arch/arm/boot/dts/sun7i-a20-bananapi-m1-plus.dts
> b/arch/arm/boot/dts/sun7i-a20-bananapi-m1-plus.dts
> new file mode 100644
> index 0000000..548ed31
> --- /dev/null
> +++ b/arch/arm/boot/dts/sun7i-a20-bananapi-m1-plus.dts
> @@ -0,0 +1,266 @@
> +/*
> + * Copyright 2016 Luo Yi <luoyi.ly@gmail.com>
> + *
> + * Thanks to the original work by Hans de Goede <hdegoede@redhat.com>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + *  a) This file is free software; you can redistribute it and/or
> + *     modify it under the terms of the GNU General Public License as
> + *     published by the Free Software Foundation; either version 2 of the
> + *     License, or (at your option) any later version.
> + *
> + *     This file is distributed in the hope that it will be useful,
> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + *     GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + *  b) Permission is hereby granted, free of charge, to any person
> + *     obtaining a copy of this software and associated documentation
> + *     files (the "Software"), to deal in the Software without
> + *     restriction, including without limitation the rights to use,
> + *     copy, modify, merge, publish, distribute, sublicense, and/or
> + *     sell copies of the Software, and to permit persons to whom the
> + *     Software is furnished to do so, subject to the following
> + *     conditions:
> + *
> + *     The above copyright notice and this permission notice shall be
> + *     included in all copies or substantial portions of the Software.
> + *
> + *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + *     OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +#include "sun7i-a20.dtsi"
> +#include "sunxi-common-regulators.dtsi"
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +
> +/ {
> +    model = "Banana Pi BPI-M1-Plus";
> +    compatible = "sinovoip,bpi-m1-plus", "allwinner,sun7i-a20";
> +
> +    aliases {
> +        serial0 = &uart0;
> +    };
> +
> +    chosen {
> +        stdout-path = "serial0:115200n8";
> +    };
> +
> +    leds {
> +        compatible = "gpio-leds";
> +        pinctrl-names = "default";
> +        pinctrl-0 = <&led_pins_bananapi>;
> +
> +        green {
> +            label = "bananapi:green:usr";
> +            gpios = <&pio 7 24 GPIO_ACTIVE_HIGH>;
> +        };
> +
> +        red {
> +            label = "bananapi:red:usr";
> +            gpios = <&pio 7 25 GPIO_ACTIVE_HIGH>;
> +            linux,default-trigger = "default-on";
> +        };
> +
> +    };
> +
> +    mmc3_pwrseq: mmc3_pwrseq {
> +        compatible = "mmc-pwrseq-simple";
> +        pinctrl-names = "default";
> +        pinctrl-0 = <&mmc3_pwrseq_pin_bananapim1plus>;
> +        reset-gpios = <&pio 7 22 GPIO_ACTIVE_LOW>; /* PH22 WL-PMU-EN */
> +    };
> +
> +    reg_gmac_3v3: gmac-3v3 {
> +        compatible = "regulator-fixed";
> +        pinctrl-names = "default";
> +        pinctrl-0 = <&gmac_power_pin_bananapi>;
> +        regulator-name = "gmac-3v3";
> +        regulator-min-microvolt = <3300000>;
> +        regulator-max-microvolt = <3300000>;
> +        startup-delay-us = <100000>;
> +        enable-active-high;
> +        gpio = <&pio 7 23 GPIO_ACTIVE_HIGH>;
> +    };
> +
> +};
> +
> +&ahci {
> +    status = "okay";
> +};
> +
> +&codec {
> +    status = "okay";
> +};
> +
> +&ehci0 {
> +    status = "okay";
> +};
> +
> +&ehci1 {
> +    status = "okay";
> +};
> +
> +&gmac {
> +    pinctrl-names = "default";
> +    pinctrl-0 = <&gmac_pins_rgmii_a>;
> +    phy = <&phy1>;
> +    phy-mode = "rgmii";
> +    phy-supply = <&reg_gmac_3v3>;
> +    status = "okay";
> +
> +    phy1: ethernet-phy at 1 {
> +        reg = <1>;
> +    };
> +};
> +
> +&i2c0 {
> +    pinctrl-names = "default";
> +    pinctrl-0 = <&i2c0_pins_a>;
> +    status = "okay";
> +
> +    axp209: pmic at 34 {
> +        compatible = "x-powers,axp209";
> +        reg = <0x34>;
> +        interrupt-parent = <&nmi_intc>;
> +        interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
> +
> +        interrupt-controller;
> +        #interrupt-cells = <1>;
> +    };
> +};
> +
> +&ir0 {
> +    pinctrl-names = "default";
> +    pinctrl-0 = <&ir0_rx_pins_a>;
> +    status = "okay";
> +};
> +
> +&mmc0 {
> +    pinctrl-names = "default";
> +    pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_bananapi>;
> +    vmmc-supply = <&reg_vcc3v3>;
> +    bus-width = <4>;
> +    cd-gpios = <&pio 7 10 GPIO_ACTIVE_HIGH>; /* PH10 */
> +    cd-inverted;
> +    status = "okay";
> +};
> +
> +&mmc3 {
> +
> +    #address-cells = <1>;
> +    #size-cells = <0>;
> +    pinctrl-names = "default";
> +    pinctrl-0 = <&mmc3_pins_a>;
> +    vmmc-supply = <&reg_vcc3v3>;
> +    mmc-pwrseq = <&mmc3_pwrseq>;
> +    bus-width = <4>;
> +    non-removable;
> +    enable-sdio-wakeup;
> +    status = "okay";
> +
> +    brcmf: bcrmf at 1 {
> +        reg = <1>;
> +        compatible = "brcm,bcm4329-fmac";
> +        interrupt-parent = <&pio>;
> +        interrupts = <7 15 IRQ_TYPE_LEVEL_LOW>;
> +        interrupt-names = "host-wake";
> +    };
> +
> +};
> +
> +&mmc3_pins_a {
> +    /* AP6210 requires pull-up */
> +    allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
> +};
> +
> +&ohci0 {
> +    status = "okay";
> +};
> +
> +&ohci1 {
> +    status = "okay";
> +};
> +
> +&pio {
> +    gmac_power_pin_bananapi: gmac_power_pin at 0 {
> +        allwinner,pins = "PH23";
> +        allwinner,function = "gpio_out";
> +        allwinner,drive = <SUN4I_PINCTRL_10_MA>;
> +        allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> +    };
> +
> +    led_pins_bananapi: led_pins at 0 {
> +        allwinner,pins = "PH24", "PG2";
> +        allwinner,function = "gpio_out";
> +        allwinner,drive = <SUN4I_PINCTRL_10_MA>;
> +        allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> +    };
> +
> +    mmc0_cd_pin_bananapi: mmc0_cd_pin at 0 {
> +        allwinner,pins = "PH10";
> +        allwinner,function = "gpio_in";
> +        allwinner,drive = <SUN4I_PINCTRL_10_MA>;
> +        allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
> +    };
> +
> +    mmc3_pwrseq_pin_bananapim1plus: mmc3_pwrseq_pin at 0 {
> +        allwinner,pins = "PH22";
> +        allwinner,function = "gpio_out";
> +        allwinner,drive = <SUN4I_PINCTRL_10_MA>;
> +        allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> +    };
> +
> +    usb1_vbus_pin_bananapi: usb1_vbus_pin at 0 {
> +        allwinner,pins = "PH0";
> +        allwinner,function = "gpio_out";
> +        allwinner,drive = <SUN4I_PINCTRL_10_MA>;
> +        allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> +    };
> +
> +    usb2_vbus_pin_bananapi: usb2_vbus_pin at 0 {
> +        allwinner,pins = "PH1";
> +        allwinner,function = "gpio_out";
> +        allwinner,drive = <SUN4I_PINCTRL_10_MA>;
> +        allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> +    };
> +
> +};
> +
> +&reg_usb1_vbus {
> +    pinctrl-0 = <&usb1_vbus_pin_bananapi>;
> +    gpio = <&pio 7 0 GPIO_ACTIVE_HIGH>; /* PH0 */
> +    status = "okay";
> +};
> +
> +&reg_usb2_vbus {
> +    pinctrl-0 = <&usb2_vbus_pin_bananapi>;
> +    gpio = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
> +    status = "okay";
> +};
> +
> +&uart0 {
> +    pinctrl-names = "default";
> +    pinctrl-0 = <&uart0_pins_a>;
> +    status = "okay";
> +};
> +
> +&usbphy {
> +    usb1_vbus-supply = <&reg_usb1_vbus>;
> +    usb2_vbus-supply = <&reg_usb2_vbus>;
> +    status = "okay";
> +};

Please include the bananapro dts to not duplicate all the common parts.

Thanks!
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20160601/d214c323/attachment.sig>