From: andrej@inversepath.com (andrej at inversepath.com)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 2/2] ARM: dts: imx53: add support for USB armory board
Date: Tue, 21 Jun 2016 16:50:53 +0200 [thread overview]
Message-ID: <20160621145053.7742-3-andrej@inversepath.com> (raw)
In-Reply-To: <20160621145053.7742-1-andrej@inversepath.com>
From: Andrej Rosano <andrej@inversepath.com>
Add support for Inverse Path USB armory board, an open source
flash-drive sized computer based on NXP i.MX53 SoC.
https://inversepath.com/usbarmory
Signed-off-by: Andrej Rosano <andrej@inversepath.com>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx53-usbarmory.dts | 239 ++++++++++++++++++++++++++++++++++
2 files changed, 240 insertions(+)
create mode 100644 arch/arm/boot/dts/imx53-usbarmory.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 414b427..f8f85ab 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -303,6 +303,7 @@ dtb-$(CONFIG_SOC_IMX53) += \
imx53-smd.dtb \
imx53-tx53-x03x.dtb \
imx53-tx53-x13x.dtb \
+ imx53-usbarmory.dtb \
imx53-voipac-bsb.dtb
dtb-$(CONFIG_SOC_IMX6Q) += \
imx6dl-apf6dev.dtb \
diff --git a/arch/arm/boot/dts/imx53-usbarmory.dts b/arch/arm/boot/dts/imx53-usbarmory.dts
new file mode 100644
index 0000000..9a172fd
--- /dev/null
+++ b/arch/arm/boot/dts/imx53-usbarmory.dts
@@ -0,0 +1,239 @@
+/*
+ * USB armory MkI device tree include file
+ * https://inversepath.com/usbarmory
+ *
+ * Copyright (C) 2015, Inverse Path
+ * Andrej Rosano <andrej@inversepath.com>
+ *
+ * Licensed under GPLv2
+ */
+
+/dts-v1/;
+#include "imx53.dtsi"
+
+/ {
+ model = "Inverse Path USB armory";
+ compatible = "inversepath,imx53-usbarmory", "fsl,imx53";
+};
+
+/ {
+ chosen {
+ stdout-path = &uart1;
+ };
+
+ memory {
+ reg = <0x70000000 0x20000000>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pin_gpio4_27>;
+
+ user {
+ label = "LED";
+ gpios = <&gpio4 27 0>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+};
+
+&cpu0 {
+ operating-points = <
+ /* kHz */
+ 166666 850000
+ 400000 900000
+ 800000 1050000
+ >;
+};
+
+&esdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_esdhc1>;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+
+ imx53-usbarmory {
+ led_pin_gpio4_27: led_gpio4_27 at 0 {
+ fsl,pins = <
+ MX53_PAD_DISP0_DAT6__GPIO4_27 0x0
+ >;
+ };
+
+ pinctrl_esdhc1: esdhc1grp {
+ fsl,pins = <
+ MX53_PAD_SD1_DATA0__ESDHC1_DAT0 0x1d5
+ MX53_PAD_SD1_DATA1__ESDHC1_DAT1 0x1d5
+ MX53_PAD_SD1_DATA2__ESDHC1_DAT2 0x1d5
+ MX53_PAD_SD1_DATA3__ESDHC1_DAT3 0x1d5
+ MX53_PAD_SD1_CMD__ESDHC1_CMD 0x1d5
+ MX53_PAD_SD1_CLK__ESDHC1_CLK 0x1d5
+ >;
+ };
+
+ pinctrl_i2c1_pmic: i2c1grp_pmic {
+ fsl,pins = <
+ MX53_PAD_EIM_D21__I2C1_SCL 0x0
+ MX53_PAD_EIM_D28__I2C1_SDA 0x0
+ >;
+ };
+
+ /*
+ * UART mode pin header configration
+ * 3 - GPIO5[26], pull-down 100K
+ * 4 - GPIO5[27], pull-down 100K
+ * 5 - TX, pull-up 100K
+ * 6 - RX, pull-up 100K
+ * 7 - GPIO5[30], pull-down 100K
+ */
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX53_PAD_CSI0_DAT8__GPIO5_26 0xc0
+ MX53_PAD_CSI0_DAT9__GPIO5_27 0xc0
+ MX53_PAD_CSI0_DAT10__UART1_TXD_MUX 0x1e4
+ MX53_PAD_CSI0_DAT11__UART1_RXD_MUX 0x1e4
+ MX53_PAD_CSI0_DAT12__GPIO5_30 0xc0
+ >;
+ };
+
+ /*
+ * GPIO mode pin header configuration
+ * 3 - GPIO5[26], pull-down 100K
+ * 4 - GPIO5[27], pull-down 100K
+ * 5 - GPIO5[28], pull-down 100K
+ * 6 - GPIO5[29], pull-down 100K
+ * 7 - GPIO5[30], pull-down 100K
+ */
+ pinctrl_gpio5: gpio5grp {
+ fsl,pins = <
+ MX53_PAD_CSI0_DAT8__GPIO5_26 0xc0
+ MX53_PAD_CSI0_DAT9__GPIO5_27 0xc0
+ MX53_PAD_CSI0_DAT10__GPIO5_28 0xc0
+ MX53_PAD_CSI0_DAT11__GPIO5_29 0xc0
+ MX53_PAD_CSI0_DAT12__GPIO5_30 0xc0
+ >;
+ };
+
+ /*
+ * SPI mode pin header configuration
+ * 3 - SCLK
+ * 4 - MOSI
+ * 5 - MISO
+ * 6 - /SS0
+ * 7 - /SS1
+ */
+ pinctrl_ecspi2: ecspi2grp {
+ fsl,pins = <
+ MX53_PAD_CSI0_DAT8__ECSPI2_SCLK 0x0
+ MX53_PAD_CSI0_DAT9__ECSPI2_MOSI 0x0
+ MX53_PAD_CSI0_DAT10__ECSPI2_MISO 0x0
+ MX53_PAD_CSI0_DAT11__GPIO5_29 0x0
+ MX53_PAD_CSI0_DAT12__GPIO5_30 0x0
+ >;
+ };
+
+ /*
+ * I2C mode pin header configuration
+ * 3 - SDA
+ * 4 - SCL
+ * 5 - GPIO5[28], pull-down 100K
+ * 6 - GPIO5[29], pull-down 100K
+ * 7 - GPIO5[30], pull-down 100K
+ */
+ pinctrl_i2c1_pinheader: i2c1grp_pinheader {
+ fsl,pins = <
+ MX53_PAD_CSI0_DAT8__I2C1_SDA 0x0
+ MX53_PAD_CSI0_DAT9__I2C1_SCL 0x0
+ MX53_PAD_CSI0_DAT10__GPIO5_28 0xc0
+ MX53_PAD_CSI0_DAT11__GPIO5_29 0xc0
+ MX53_PAD_CSI0_DAT12__GPIO5_30 0xc0
+ >;
+ };
+ };
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&usbotg {
+ dr_mode = "peripheral";
+ status = "okay";
+};
+
+&i2c1 {
+ pinctrl-0 = <&pinctrl_i2c1_pmic>;
+ status = "okay";
+ ltc3589: pmic at 34 {
+ compatible = "lltc,ltc3589-2";
+ reg = <0x34>;
+ regulators {
+ sw1_reg: sw1 {
+ regulator-min-microvolt = <591930>;
+ regulator-max-microvolt = <1224671>;
+ lltc,fb-voltage-divider = <100000 158000>;
+ regulator-ramp-delay = <7000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw2_reg: sw2 {
+ regulator-min-microvolt = <704123>;
+ regulator-max-microvolt = <1456803>;
+ lltc,fb-voltage-divider = <180000 191000>;
+ regulator-ramp-delay = <7000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw3_reg: sw3 {
+ regulator-min-microvolt = <1341250>;
+ regulator-max-microvolt = <2775000>;
+ lltc,fb-voltage-divider = <270000 100000>;
+ regulator-ramp-delay = <7000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ bb_out_reg: bb-out {
+ regulator-min-microvolt = <3387341>;
+ regulator-max-microvolt = <3387341>;
+ lltc,fb-voltage-divider = <511000 158000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ ldo1_reg: ldo1 {
+ regulator-min-microvolt = <1306329>;
+ regulator-max-microvolt = <1306329>;
+ lltc,fb-voltage-divider = <100000 158000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo2_reg: ldo2 {
+ regulator-min-microvolt = <704123>;
+ regulator-max-microvolt = <1456806>;
+ lltc,fb-voltage-divider = <180000 191000>;
+ regulator-ramp-delay = <7000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo3_reg: ldo3 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-boot-on;
+ };
+
+ ldo4_reg: ldo4 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <3200000>;
+ };
+ };
+ };
+};
--
2.9.0
WARNING: multiple messages have this Message-ID (diff)
From: andrej@inversepath.com
To: devicetree@vger.kernel.org
Cc: Vagrant Cascadian <vagrant@debian.org>,
linux-kernel@vger.kernel.org,
Sascha Hauer <kernel@pengutronix.de>,
Fabio Estevam <fabio.estevam@nxp.com>,
Shawn Guo <shawnguo@kernel.org>,
linux-arm-kernel@lists.infradead.org
Subject: [PATCH 2/2] ARM: dts: imx53: add support for USB armory board
Date: Tue, 21 Jun 2016 16:50:53 +0200 [thread overview]
Message-ID: <20160621145053.7742-3-andrej@inversepath.com> (raw)
In-Reply-To: <20160621145053.7742-1-andrej@inversepath.com>
From: Andrej Rosano <andrej@inversepath.com>
Add support for Inverse Path USB armory board, an open source
flash-drive sized computer based on NXP i.MX53 SoC.
https://inversepath.com/usbarmory
Signed-off-by: Andrej Rosano <andrej@inversepath.com>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx53-usbarmory.dts | 239 ++++++++++++++++++++++++++++++++++
2 files changed, 240 insertions(+)
create mode 100644 arch/arm/boot/dts/imx53-usbarmory.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 414b427..f8f85ab 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -303,6 +303,7 @@ dtb-$(CONFIG_SOC_IMX53) += \
imx53-smd.dtb \
imx53-tx53-x03x.dtb \
imx53-tx53-x13x.dtb \
+ imx53-usbarmory.dtb \
imx53-voipac-bsb.dtb
dtb-$(CONFIG_SOC_IMX6Q) += \
imx6dl-apf6dev.dtb \
diff --git a/arch/arm/boot/dts/imx53-usbarmory.dts b/arch/arm/boot/dts/imx53-usbarmory.dts
new file mode 100644
index 0000000..9a172fd
--- /dev/null
+++ b/arch/arm/boot/dts/imx53-usbarmory.dts
@@ -0,0 +1,239 @@
+/*
+ * USB armory MkI device tree include file
+ * https://inversepath.com/usbarmory
+ *
+ * Copyright (C) 2015, Inverse Path
+ * Andrej Rosano <andrej@inversepath.com>
+ *
+ * Licensed under GPLv2
+ */
+
+/dts-v1/;
+#include "imx53.dtsi"
+
+/ {
+ model = "Inverse Path USB armory";
+ compatible = "inversepath,imx53-usbarmory", "fsl,imx53";
+};
+
+/ {
+ chosen {
+ stdout-path = &uart1;
+ };
+
+ memory {
+ reg = <0x70000000 0x20000000>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pin_gpio4_27>;
+
+ user {
+ label = "LED";
+ gpios = <&gpio4 27 0>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+};
+
+&cpu0 {
+ operating-points = <
+ /* kHz */
+ 166666 850000
+ 400000 900000
+ 800000 1050000
+ >;
+};
+
+&esdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_esdhc1>;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+
+ imx53-usbarmory {
+ led_pin_gpio4_27: led_gpio4_27@0 {
+ fsl,pins = <
+ MX53_PAD_DISP0_DAT6__GPIO4_27 0x0
+ >;
+ };
+
+ pinctrl_esdhc1: esdhc1grp {
+ fsl,pins = <
+ MX53_PAD_SD1_DATA0__ESDHC1_DAT0 0x1d5
+ MX53_PAD_SD1_DATA1__ESDHC1_DAT1 0x1d5
+ MX53_PAD_SD1_DATA2__ESDHC1_DAT2 0x1d5
+ MX53_PAD_SD1_DATA3__ESDHC1_DAT3 0x1d5
+ MX53_PAD_SD1_CMD__ESDHC1_CMD 0x1d5
+ MX53_PAD_SD1_CLK__ESDHC1_CLK 0x1d5
+ >;
+ };
+
+ pinctrl_i2c1_pmic: i2c1grp_pmic {
+ fsl,pins = <
+ MX53_PAD_EIM_D21__I2C1_SCL 0x0
+ MX53_PAD_EIM_D28__I2C1_SDA 0x0
+ >;
+ };
+
+ /*
+ * UART mode pin header configration
+ * 3 - GPIO5[26], pull-down 100K
+ * 4 - GPIO5[27], pull-down 100K
+ * 5 - TX, pull-up 100K
+ * 6 - RX, pull-up 100K
+ * 7 - GPIO5[30], pull-down 100K
+ */
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX53_PAD_CSI0_DAT8__GPIO5_26 0xc0
+ MX53_PAD_CSI0_DAT9__GPIO5_27 0xc0
+ MX53_PAD_CSI0_DAT10__UART1_TXD_MUX 0x1e4
+ MX53_PAD_CSI0_DAT11__UART1_RXD_MUX 0x1e4
+ MX53_PAD_CSI0_DAT12__GPIO5_30 0xc0
+ >;
+ };
+
+ /*
+ * GPIO mode pin header configuration
+ * 3 - GPIO5[26], pull-down 100K
+ * 4 - GPIO5[27], pull-down 100K
+ * 5 - GPIO5[28], pull-down 100K
+ * 6 - GPIO5[29], pull-down 100K
+ * 7 - GPIO5[30], pull-down 100K
+ */
+ pinctrl_gpio5: gpio5grp {
+ fsl,pins = <
+ MX53_PAD_CSI0_DAT8__GPIO5_26 0xc0
+ MX53_PAD_CSI0_DAT9__GPIO5_27 0xc0
+ MX53_PAD_CSI0_DAT10__GPIO5_28 0xc0
+ MX53_PAD_CSI0_DAT11__GPIO5_29 0xc0
+ MX53_PAD_CSI0_DAT12__GPIO5_30 0xc0
+ >;
+ };
+
+ /*
+ * SPI mode pin header configuration
+ * 3 - SCLK
+ * 4 - MOSI
+ * 5 - MISO
+ * 6 - /SS0
+ * 7 - /SS1
+ */
+ pinctrl_ecspi2: ecspi2grp {
+ fsl,pins = <
+ MX53_PAD_CSI0_DAT8__ECSPI2_SCLK 0x0
+ MX53_PAD_CSI0_DAT9__ECSPI2_MOSI 0x0
+ MX53_PAD_CSI0_DAT10__ECSPI2_MISO 0x0
+ MX53_PAD_CSI0_DAT11__GPIO5_29 0x0
+ MX53_PAD_CSI0_DAT12__GPIO5_30 0x0
+ >;
+ };
+
+ /*
+ * I2C mode pin header configuration
+ * 3 - SDA
+ * 4 - SCL
+ * 5 - GPIO5[28], pull-down 100K
+ * 6 - GPIO5[29], pull-down 100K
+ * 7 - GPIO5[30], pull-down 100K
+ */
+ pinctrl_i2c1_pinheader: i2c1grp_pinheader {
+ fsl,pins = <
+ MX53_PAD_CSI0_DAT8__I2C1_SDA 0x0
+ MX53_PAD_CSI0_DAT9__I2C1_SCL 0x0
+ MX53_PAD_CSI0_DAT10__GPIO5_28 0xc0
+ MX53_PAD_CSI0_DAT11__GPIO5_29 0xc0
+ MX53_PAD_CSI0_DAT12__GPIO5_30 0xc0
+ >;
+ };
+ };
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&usbotg {
+ dr_mode = "peripheral";
+ status = "okay";
+};
+
+&i2c1 {
+ pinctrl-0 = <&pinctrl_i2c1_pmic>;
+ status = "okay";
+ ltc3589: pmic@34 {
+ compatible = "lltc,ltc3589-2";
+ reg = <0x34>;
+ regulators {
+ sw1_reg: sw1 {
+ regulator-min-microvolt = <591930>;
+ regulator-max-microvolt = <1224671>;
+ lltc,fb-voltage-divider = <100000 158000>;
+ regulator-ramp-delay = <7000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw2_reg: sw2 {
+ regulator-min-microvolt = <704123>;
+ regulator-max-microvolt = <1456803>;
+ lltc,fb-voltage-divider = <180000 191000>;
+ regulator-ramp-delay = <7000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw3_reg: sw3 {
+ regulator-min-microvolt = <1341250>;
+ regulator-max-microvolt = <2775000>;
+ lltc,fb-voltage-divider = <270000 100000>;
+ regulator-ramp-delay = <7000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ bb_out_reg: bb-out {
+ regulator-min-microvolt = <3387341>;
+ regulator-max-microvolt = <3387341>;
+ lltc,fb-voltage-divider = <511000 158000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ ldo1_reg: ldo1 {
+ regulator-min-microvolt = <1306329>;
+ regulator-max-microvolt = <1306329>;
+ lltc,fb-voltage-divider = <100000 158000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo2_reg: ldo2 {
+ regulator-min-microvolt = <704123>;
+ regulator-max-microvolt = <1456806>;
+ lltc,fb-voltage-divider = <180000 191000>;
+ regulator-ramp-delay = <7000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo3_reg: ldo3 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-boot-on;
+ };
+
+ ldo4_reg: ldo4 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <3200000>;
+ };
+ };
+ };
+};
--
2.9.0
WARNING: multiple messages have this Message-ID (diff)
From: andrej@inversepath.com
To: devicetree@vger.kernel.org
Cc: Shawn Guo <shawnguo@kernel.org>,
Sascha Hauer <kernel@pengutronix.de>,
Fabio Estevam <fabio.estevam@nxp.com>,
linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org,
Vagrant Cascadian <vagrant@debian.org>
Subject: [PATCH 2/2] ARM: dts: imx53: add support for USB armory board
Date: Tue, 21 Jun 2016 16:50:53 +0200 [thread overview]
Message-ID: <20160621145053.7742-3-andrej@inversepath.com> (raw)
In-Reply-To: <20160621145053.7742-1-andrej@inversepath.com>
From: Andrej Rosano <andrej@inversepath.com>
Add support for Inverse Path USB armory board, an open source
flash-drive sized computer based on NXP i.MX53 SoC.
https://inversepath.com/usbarmory
Signed-off-by: Andrej Rosano <andrej@inversepath.com>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx53-usbarmory.dts | 239 ++++++++++++++++++++++++++++++++++
2 files changed, 240 insertions(+)
create mode 100644 arch/arm/boot/dts/imx53-usbarmory.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 414b427..f8f85ab 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -303,6 +303,7 @@ dtb-$(CONFIG_SOC_IMX53) += \
imx53-smd.dtb \
imx53-tx53-x03x.dtb \
imx53-tx53-x13x.dtb \
+ imx53-usbarmory.dtb \
imx53-voipac-bsb.dtb
dtb-$(CONFIG_SOC_IMX6Q) += \
imx6dl-apf6dev.dtb \
diff --git a/arch/arm/boot/dts/imx53-usbarmory.dts b/arch/arm/boot/dts/imx53-usbarmory.dts
new file mode 100644
index 0000000..9a172fd
--- /dev/null
+++ b/arch/arm/boot/dts/imx53-usbarmory.dts
@@ -0,0 +1,239 @@
+/*
+ * USB armory MkI device tree include file
+ * https://inversepath.com/usbarmory
+ *
+ * Copyright (C) 2015, Inverse Path
+ * Andrej Rosano <andrej@inversepath.com>
+ *
+ * Licensed under GPLv2
+ */
+
+/dts-v1/;
+#include "imx53.dtsi"
+
+/ {
+ model = "Inverse Path USB armory";
+ compatible = "inversepath,imx53-usbarmory", "fsl,imx53";
+};
+
+/ {
+ chosen {
+ stdout-path = &uart1;
+ };
+
+ memory {
+ reg = <0x70000000 0x20000000>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pin_gpio4_27>;
+
+ user {
+ label = "LED";
+ gpios = <&gpio4 27 0>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+};
+
+&cpu0 {
+ operating-points = <
+ /* kHz */
+ 166666 850000
+ 400000 900000
+ 800000 1050000
+ >;
+};
+
+&esdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_esdhc1>;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+
+ imx53-usbarmory {
+ led_pin_gpio4_27: led_gpio4_27@0 {
+ fsl,pins = <
+ MX53_PAD_DISP0_DAT6__GPIO4_27 0x0
+ >;
+ };
+
+ pinctrl_esdhc1: esdhc1grp {
+ fsl,pins = <
+ MX53_PAD_SD1_DATA0__ESDHC1_DAT0 0x1d5
+ MX53_PAD_SD1_DATA1__ESDHC1_DAT1 0x1d5
+ MX53_PAD_SD1_DATA2__ESDHC1_DAT2 0x1d5
+ MX53_PAD_SD1_DATA3__ESDHC1_DAT3 0x1d5
+ MX53_PAD_SD1_CMD__ESDHC1_CMD 0x1d5
+ MX53_PAD_SD1_CLK__ESDHC1_CLK 0x1d5
+ >;
+ };
+
+ pinctrl_i2c1_pmic: i2c1grp_pmic {
+ fsl,pins = <
+ MX53_PAD_EIM_D21__I2C1_SCL 0x0
+ MX53_PAD_EIM_D28__I2C1_SDA 0x0
+ >;
+ };
+
+ /*
+ * UART mode pin header configration
+ * 3 - GPIO5[26], pull-down 100K
+ * 4 - GPIO5[27], pull-down 100K
+ * 5 - TX, pull-up 100K
+ * 6 - RX, pull-up 100K
+ * 7 - GPIO5[30], pull-down 100K
+ */
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX53_PAD_CSI0_DAT8__GPIO5_26 0xc0
+ MX53_PAD_CSI0_DAT9__GPIO5_27 0xc0
+ MX53_PAD_CSI0_DAT10__UART1_TXD_MUX 0x1e4
+ MX53_PAD_CSI0_DAT11__UART1_RXD_MUX 0x1e4
+ MX53_PAD_CSI0_DAT12__GPIO5_30 0xc0
+ >;
+ };
+
+ /*
+ * GPIO mode pin header configuration
+ * 3 - GPIO5[26], pull-down 100K
+ * 4 - GPIO5[27], pull-down 100K
+ * 5 - GPIO5[28], pull-down 100K
+ * 6 - GPIO5[29], pull-down 100K
+ * 7 - GPIO5[30], pull-down 100K
+ */
+ pinctrl_gpio5: gpio5grp {
+ fsl,pins = <
+ MX53_PAD_CSI0_DAT8__GPIO5_26 0xc0
+ MX53_PAD_CSI0_DAT9__GPIO5_27 0xc0
+ MX53_PAD_CSI0_DAT10__GPIO5_28 0xc0
+ MX53_PAD_CSI0_DAT11__GPIO5_29 0xc0
+ MX53_PAD_CSI0_DAT12__GPIO5_30 0xc0
+ >;
+ };
+
+ /*
+ * SPI mode pin header configuration
+ * 3 - SCLK
+ * 4 - MOSI
+ * 5 - MISO
+ * 6 - /SS0
+ * 7 - /SS1
+ */
+ pinctrl_ecspi2: ecspi2grp {
+ fsl,pins = <
+ MX53_PAD_CSI0_DAT8__ECSPI2_SCLK 0x0
+ MX53_PAD_CSI0_DAT9__ECSPI2_MOSI 0x0
+ MX53_PAD_CSI0_DAT10__ECSPI2_MISO 0x0
+ MX53_PAD_CSI0_DAT11__GPIO5_29 0x0
+ MX53_PAD_CSI0_DAT12__GPIO5_30 0x0
+ >;
+ };
+
+ /*
+ * I2C mode pin header configuration
+ * 3 - SDA
+ * 4 - SCL
+ * 5 - GPIO5[28], pull-down 100K
+ * 6 - GPIO5[29], pull-down 100K
+ * 7 - GPIO5[30], pull-down 100K
+ */
+ pinctrl_i2c1_pinheader: i2c1grp_pinheader {
+ fsl,pins = <
+ MX53_PAD_CSI0_DAT8__I2C1_SDA 0x0
+ MX53_PAD_CSI0_DAT9__I2C1_SCL 0x0
+ MX53_PAD_CSI0_DAT10__GPIO5_28 0xc0
+ MX53_PAD_CSI0_DAT11__GPIO5_29 0xc0
+ MX53_PAD_CSI0_DAT12__GPIO5_30 0xc0
+ >;
+ };
+ };
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&usbotg {
+ dr_mode = "peripheral";
+ status = "okay";
+};
+
+&i2c1 {
+ pinctrl-0 = <&pinctrl_i2c1_pmic>;
+ status = "okay";
+ ltc3589: pmic@34 {
+ compatible = "lltc,ltc3589-2";
+ reg = <0x34>;
+ regulators {
+ sw1_reg: sw1 {
+ regulator-min-microvolt = <591930>;
+ regulator-max-microvolt = <1224671>;
+ lltc,fb-voltage-divider = <100000 158000>;
+ regulator-ramp-delay = <7000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw2_reg: sw2 {
+ regulator-min-microvolt = <704123>;
+ regulator-max-microvolt = <1456803>;
+ lltc,fb-voltage-divider = <180000 191000>;
+ regulator-ramp-delay = <7000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw3_reg: sw3 {
+ regulator-min-microvolt = <1341250>;
+ regulator-max-microvolt = <2775000>;
+ lltc,fb-voltage-divider = <270000 100000>;
+ regulator-ramp-delay = <7000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ bb_out_reg: bb-out {
+ regulator-min-microvolt = <3387341>;
+ regulator-max-microvolt = <3387341>;
+ lltc,fb-voltage-divider = <511000 158000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ ldo1_reg: ldo1 {
+ regulator-min-microvolt = <1306329>;
+ regulator-max-microvolt = <1306329>;
+ lltc,fb-voltage-divider = <100000 158000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo2_reg: ldo2 {
+ regulator-min-microvolt = <704123>;
+ regulator-max-microvolt = <1456806>;
+ lltc,fb-voltage-divider = <180000 191000>;
+ regulator-ramp-delay = <7000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo3_reg: ldo3 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-boot-on;
+ };
+
+ ldo4_reg: ldo4 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <3200000>;
+ };
+ };
+ };
+};
--
2.9.0
next prev parent reply other threads:[~2016-06-21 14:50 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-06-21 14:50 [PATCH 0/2] ARM: dts: imx53: add support for USB armory board andrej at inversepath.com
2016-06-21 14:50 ` andrej
2016-06-21 14:50 ` andrej
2016-06-21 14:50 ` [PATCH 1/2] devicetree: Add vendor prefix for Inverse Path andrej at inversepath.com
2016-06-21 14:50 ` andrej
2016-06-21 14:50 ` andrej
2016-06-21 21:59 ` Rob Herring
2016-06-21 21:59 ` Rob Herring
2016-06-21 14:50 ` andrej at inversepath.com [this message]
2016-06-21 14:50 ` [PATCH 2/2] ARM: dts: imx53: add support for USB armory board andrej
2016-06-21 14:50 ` andrej
2016-06-28 1:50 ` Shawn Guo
2016-06-28 1:50 ` Shawn Guo
2016-06-28 1:50 ` Shawn Guo
2016-06-28 13:24 ` Andrej Rosano
2016-06-28 13:24 ` Andrej Rosano
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20160621145053.7742-3-andrej@inversepath.com \
--to=andrej@inversepath.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.