[PATCH net-next v10 0/1] net: phy: Cleanup the Edge-Rate feature in Microsemi PHYs.

[PATCH net-next v10 0/1] net: phy: Cleanup the Edge-Rate feature in Microsemi PHYs.

[Allan W. Nielsen]

Hi All,

Yet another iteration on the edge rate.

Included in this iteration:
- vdd and slowdown is removed from private structure
- rate_magic added to private structure
- devicetree settings is read and validated in probe instead of init
- unused reference in device-tree doc removed

Please review

/Allan

[PATCH net-next v10 1/1] net: phy: Cleanup the Edge-Rate feature in Microsemi PHYs.

[Allan W. Nielsen]

Edge-Rate cleanup include the following:
- Updated device tree bindings documentation for edge-rate
- The edge-rate is now specified as a "slowdown", meaning that it is now
  being specified as positive values instead of negative (both
  documentation and implementation wise).
- Only explicitly documented values for "vsc8531,vddmac" and
  "vsc8531,edge-slowdown" are accepted by the device driver.
- Deleted include/dt-bindings/net/mscc-phy-vsc8531.h as it was not needed.
- Read/validate devicetree settings in probe instead of init

Signed-off-by: Allan W. Nielsen <allan.nielsen@microsemi.com>
Signed-off-by: Raju Lakkaraju <raju.lakkaraju@microsemi.com>
---
 .../devicetree/bindings/net/mscc-phy-vsc8531.txt   |  51 +++++----
 drivers/net/phy/mscc.c                             | 127 ++++++++++-----------
 include/dt-bindings/net/mscc-phy-vsc8531.h         |  21 ----
 3 files changed, 86 insertions(+), 113 deletions(-)
 delete mode 100644 include/dt-bindings/net/mscc-phy-vsc8531.h

diff --git a/Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt b/Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt
index 99c7eb0..bdefefc6 100644
--- a/Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt
+++ b/Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt
@@ -6,22 +6,27 @@ Required properties:
 		  Documentation/devicetree/bindings/net/phy.txt
 
 Optional properties:
-- vsc8531,vddmac	: The vddmac in mV.
+- vsc8531,vddmac	: The vddmac in mV. Allowed values is listed
+			  in the first row of Table 1 (below).
+			  This property is only used in combination
+			  with the 'edge-slowdown' property.
+			  Default value is 3300.
 - vsc8531,edge-slowdown	: % the edge should be slowed down relative to
-			  the fastest possible edge time. Native sign
-			  need not enter.
+			  the fastest possible edge time.
 			  Edge rate sets the drive strength of the MAC
-			  interface output signals.  Changing the drive
-			  strength will affect the edge rate of the output
-			  signal.  The goal of this setting is to help
-			  reduce electrical emission (EMI) by being able
-			  to reprogram drive strength and in effect slow
-			  down the edge rate if desired.  Table 1 shows the
-			  impact to the edge rate per VDDMAC supply for each
-			  drive strength setting.
-			  Ref: Table:1 - Edge rate change below.
-
-Note: see dt-bindings/net/mscc-phy-vsc8531.h for applicable values
+			  interface output signals.  Changing the
+			  drive strength will affect the edge rate of
+			  the output signal.  The goal of this setting
+			  is to help reduce electrical emission (EMI)
+			  by being able to reprogram drive strength
+			  and in effect slow down the edge rate if
+			  desired.
+			  To adjust the edge-slowdown, the 'vddmac'
+			  must be specified. Table 1 lists the
+			  supported edge-slowdown values for a given
+			  'vddmac'.
+			  Default value is 0%.
+			  Ref: Table:1 - Edge rate change (below).
 
 Table: 1 - Edge rate change
 ----------------------------------------------------------------|
@@ -29,23 +34,23 @@ Table: 1 - Edge rate change
 |								|
 | 3300 mV	2500 mV		1800 mV		1500 mV		|
 |---------------------------------------------------------------|
-| Default	Deafult		Default		Default		|
+| 0%		0%		0%		0%		|
 | (Fastest)			(recommended)	(recommended)	|
 |---------------------------------------------------------------|
-| -2%		-3%		-5%		-6%		|
+| 2%		3%		5%		6%		|
 |---------------------------------------------------------------|
-| -4%		-6%		-9%		-14%		|
+| 4%		6%		9%		14%		|
 |---------------------------------------------------------------|
-| -7%		-10%		-16%		-21%		|
+| 7%		10%		16%		21%		|
 |(recommended)	(recommended)					|
 |---------------------------------------------------------------|
-| -10%		-14%		-23%		-29%		|
+| 10%		14%		23%		29%		|
 |---------------------------------------------------------------|
-| -17%		-23%		-35%		-42%		|
+| 17%		23%		35%		42%		|
 |---------------------------------------------------------------|
-| -29%		-37%		-52%		-58%		|
+| 29%		37%		52%		58%		|
 |---------------------------------------------------------------|
-| -53%		-63%		-76%		-77%		|
+| 53%		63%		76%		77%		|
 | (slowest)							|
 |---------------------------------------------------------------|
 
@@ -54,5 +59,5 @@ Example:
         vsc8531_0: ethernet-phy@0 {
                 compatible = "ethernet-phy-id0007.0570";
                 vsc8531,vddmac		= <3300>;
-                vsc8531,edge-slowdown	= <21>;
+                vsc8531,edge-slowdown	= <7>;
         };
diff --git a/drivers/net/phy/mscc.c b/drivers/net/phy/mscc.c
index a17573e..405ab0e 100644
--- a/drivers/net/phy/mscc.c
+++ b/drivers/net/phy/mscc.c
@@ -12,7 +12,6 @@
 #include <linux/mii.h>
 #include <linux/phy.h>
 #include <linux/of.h>
-#include <dt-bindings/net/mscc-phy-vsc8531.h>
 
 enum rgmii_rx_clock_delay {
 	RGMII_RX_CLK_DELAY_0_2_NS = 0,
@@ -56,23 +55,29 @@ enum rgmii_rx_clock_delay {
 #define PHY_ID_VSC8531			  0x00070570
 #define PHY_ID_VSC8541			  0x00070770
 
-struct edge_rate_table {
-	u16 vddmac;
-	int slowdown[MSCC_SLOWDOWN_MAX];
-};
+#define MSCC_VDDMAC_1500		  1500
+#define MSCC_VDDMAC_1800		  1800
+#define MSCC_VDDMAC_2500		  2500
+#define MSCC_VDDMAC_3300		  3300
 
-struct edge_rate_table edge_table[MSCC_VDDMAC_MAX] = {
-	{3300, { 0, -2, -4,  -7,  -10, -17, -29, -53} },
-	{2500, { 0, -3, -6,  -10, -14, -23, -37, -63} },
-	{1800, { 0, -5, -9,  -16, -23, -35, -52, -76} },
-	{1500, { 0, -6, -14, -21, -29, -42, -58, -77} },
+struct vsc8531_private {
+	int rate_magic;
 };
 
-struct vsc8531_private {
-	u8 edge_slowdown;
+#ifdef CONFIG_OF_MDIO
+struct vsc8531_edge_rate_table {
 	u16 vddmac;
+	u8 slowdown[8];
 };
 
+static const struct vsc8531_edge_rate_table edge_table[] = {
+	{MSCC_VDDMAC_3300, { 0, 2,  4,  7, 10, 17, 29, 53} },
+	{MSCC_VDDMAC_2500, { 0, 3,  6, 10, 14, 23, 37, 63} },
+	{MSCC_VDDMAC_1800, { 0, 5,  9, 16, 23, 35, 52, 76} },
+	{MSCC_VDDMAC_1500, { 0, 6, 14, 21, 29, 42, 58, 77} },
+};
+#endif /* CONFIG_OF_MDIO */
+
 static int vsc85xx_phy_page_set(struct phy_device *phydev, u8 page)
 {
 	int rc;
@@ -81,29 +86,43 @@ static int vsc85xx_phy_page_set(struct phy_device *phydev, u8 page)
 	return rc;
 }
 
-static u8 edge_rate_magic_get(u16 vddmac,
-			      int slowdown)
+#ifdef CONFIG_OF_MDIO
+static int vsc85xx_edge_rate_magic_get(struct phy_device *phydev)
 {
-	int rc = (MSCC_SLOWDOWN_MAX - 1);
-	u8 vdd;
 	u8 sd;
+	u16 vdd;
+	int rc, i, j;
+	struct device *dev = &phydev->mdio.dev;
+	struct device_node *of_node = dev->of_node;
+	u8 sd_array_size = ARRAY_SIZE(edge_table[0].slowdown);
 
-	for (vdd = 0; vdd < MSCC_VDDMAC_MAX; vdd++) {
-		if (edge_table[vdd].vddmac == vddmac) {
-			for (sd = 0; sd < MSCC_SLOWDOWN_MAX; sd++) {
-				if (edge_table[vdd].slowdown[sd] <= slowdown) {
-					rc = (MSCC_SLOWDOWN_MAX - sd - 1);
-					break;
-				}
-			}
-		}
-	}
+	if (!of_node)
+		return -ENODEV;
 
-	return rc;
+	rc = of_property_read_u16(of_node, "vsc8531,vddmac", &vdd);
+	if (rc != 0)
+		vdd = MSCC_VDDMAC_3300;
+
+	rc = of_property_read_u8(of_node, "vsc8531,edge-slowdown", &sd);
+	if (rc != 0)
+		sd = 0;
+
+	for (i = 0; i < ARRAY_SIZE(edge_table); i++)
+		if (edge_table[i].vddmac == vdd)
+			for (j = 0; j < sd_array_size; j++)
+				if (edge_table[i].slowdown[j] == sd)
+					return (sd_array_size - j - 1);
+
+	return -EINVAL;
+}
+#else
+static int vsc85xx_edge_rate_magic_get(struct phy_device *phydev)
+{
+	return 0;
 }
+#endif /* CONFIG_OF_MDIO */
 
-static int vsc85xx_edge_rate_cntl_set(struct phy_device *phydev,
-				      u8 edge_rate)
+static int vsc85xx_edge_rate_cntl_set(struct phy_device *phydev, u8 edge_rate)
 {
 	int rc;
 	u16 reg_val;
@@ -184,45 +203,10 @@ out_unlock:
 	return rc;
 }
 
-#ifdef CONFIG_OF_MDIO
-static int vsc8531_of_init(struct phy_device *phydev)
-{
-	int rc;
-	struct vsc8531_private *vsc8531 = phydev->priv;
-	struct device *dev = &phydev->mdio.dev;
-	struct device_node *of_node = dev->of_node;
-
-	if (!of_node)
-		return -ENODEV;
-
-	rc = of_property_read_u16(of_node, "vsc8531,vddmac",
-				  &vsc8531->vddmac);
-	if (rc == -EINVAL)
-		vsc8531->vddmac = MSCC_VDDMAC_3300;
-	rc = of_property_read_u8(of_node, "vsc8531,edge-slowdown",
-				 &vsc8531->edge_slowdown);
-	if (rc == -EINVAL)
-		vsc8531->edge_slowdown = 0;
-
-	rc = 0;
-	return rc;
-}
-#else
-static int vsc8531_of_init(struct phy_device *phydev)
-{
-	return 0;
-}
-#endif /* CONFIG_OF_MDIO */
-
 static int vsc85xx_config_init(struct phy_device *phydev)
 {
 	int rc;
 	struct vsc8531_private *vsc8531 = phydev->priv;
-	u8 edge_rate;
-
-	rc = vsc8531_of_init(phydev);
-	if (rc)
-		return rc;
 
 	rc = vsc85xx_default_config(phydev);
 	if (rc)
@@ -232,9 +216,7 @@ static int vsc85xx_config_init(struct phy_device *phydev)
 	if (rc)
 		return rc;
 
-	edge_rate = edge_rate_magic_get(vsc8531->vddmac,
-					-(int)vsc8531->edge_slowdown);
-	rc = vsc85xx_edge_rate_cntl_set(phydev, edge_rate);
+	rc = vsc85xx_edge_rate_cntl_set(phydev, vsc8531->rate_magic);
 	if (rc)
 		return rc;
 
@@ -272,14 +254,21 @@ static int vsc85xx_config_intr(struct phy_device *phydev)
 
 static int vsc85xx_probe(struct phy_device *phydev)
 {
+	int rate_magic;
 	struct vsc8531_private *vsc8531;
 
+	rate_magic = vsc85xx_edge_rate_magic_get(phydev);
+	if (rate_magic < 0)
+		return rate_magic;
+
 	vsc8531 = devm_kzalloc(&phydev->mdio.dev, sizeof(*vsc8531), GFP_KERNEL);
 	if (!vsc8531)
 		return -ENOMEM;
 
 	phydev->priv = vsc8531;
 
+	vsc8531->rate_magic = rate_magic;
+
 	return 0;
 }
 
@@ -300,7 +289,7 @@ static struct phy_driver vsc85xx_driver[] = {
 	.config_intr    = &vsc85xx_config_intr,
 	.suspend	= &genphy_suspend,
 	.resume		= &genphy_resume,
-	.probe          = &vsc85xx_probe,
+	.probe		= &vsc85xx_probe,
 },
 {
 	.phy_id		= PHY_ID_VSC8541,
@@ -317,7 +306,7 @@ static struct phy_driver vsc85xx_driver[] = {
 	.config_intr    = &vsc85xx_config_intr,
 	.suspend	= &genphy_suspend,
 	.resume		= &genphy_resume,
-	.probe          = &vsc85xx_probe,
+	.probe		= &vsc85xx_probe,
 }
 
 };
diff --git a/include/dt-bindings/net/mscc-phy-vsc8531.h b/include/dt-bindings/net/mscc-phy-vsc8531.h
deleted file mode 100644
index 2383dd2..0000000
--- a/include/dt-bindings/net/mscc-phy-vsc8531.h
+++ /dev/null
@@ -1,21 +0,0 @@
-/*
- * Device Tree constants for Microsemi VSC8531 PHY
- *
- * Author: Nagaraju Lakkaraju
- *
- * License: Dual MIT/GPL
- * Copyright (c) 2016 Microsemi Corporation
- */
-
-#ifndef _DT_BINDINGS_MSCC_VSC8531_H
-#define _DT_BINDINGS_MSCC_VSC8531_H
-
-/* MAC interface Edge rate control VDDMAC in milli Volts */
-#define MSCC_VDDMAC_3300		 3300
-#define MSCC_VDDMAC_2500		 2500
-#define MSCC_VDDMAC_1800		 1800
-#define MSCC_VDDMAC_1500		 1500
-#define MSCC_VDDMAC_MAX			 4
-#define MSCC_SLOWDOWN_MAX		 8
-
-#endif
-- 
2.7.3

Re: [PATCH net-next v10 1/1] net: phy: Cleanup the Edge-Rate feature in Microsemi PHYs.

[Andrew Lunn]

On Mon, Oct 10, 2016 at 04:13:45PM +0200, Allan W. Nielsen wrote:
> Edge-Rate cleanup include the following:
> - Updated device tree bindings documentation for edge-rate
> - The edge-rate is now specified as a "slowdown", meaning that it is now
>   being specified as positive values instead of negative (both
>   documentation and implementation wise).
> - Only explicitly documented values for "vsc8531,vddmac" and
>   "vsc8531,edge-slowdown" are accepted by the device driver.
> - Deleted include/dt-bindings/net/mscc-phy-vsc8531.h as it was not needed.
> - Read/validate devicetree settings in probe instead of init
> 
> Signed-off-by: Allan W. Nielsen <allan.nielsen@microsemi.com>
> Signed-off-by: Raju Lakkaraju <raju.lakkaraju@microsemi.com>

Hi Raju, Allan

Thanks for keeping at this.

Reviewed-by: Andrew Lunn <andrew@lunn.ch>

    Andrew

Re: [PATCH net-next v10 1/1] net: phy: Cleanup the Edge-Rate feature in Microsemi PHYs.

[Florian Fainelli]

On 10/10/2016 07:13 AM, Allan W. Nielsen wrote:
> Edge-Rate cleanup include the following:
> - Updated device tree bindings documentation for edge-rate
> - The edge-rate is now specified as a "slowdown", meaning that it is now
>   being specified as positive values instead of negative (both
>   documentation and implementation wise).
> - Only explicitly documented values for "vsc8531,vddmac" and
>   "vsc8531,edge-slowdown" are accepted by the device driver.
> - Deleted include/dt-bindings/net/mscc-phy-vsc8531.h as it was not needed.
> - Read/validate devicetree settings in probe instead of init
> 
> Signed-off-by: Allan W. Nielsen <allan.nielsen@microsemi.com>
> Signed-off-by: Raju Lakkaraju <raju.lakkaraju@microsemi.com>

Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
-- 
Florian

Re: [PATCH net-next v10 1/1] net: phy: Cleanup the Edge-Rate feature in Microsemi PHYs.

[David Miller]

From: "Allan W. Nielsen" <allan.nielsen@microsemi.com>
Date: Mon, 10 Oct 2016 16:13:45 +0200

> Edge-Rate cleanup include the following:
> - Updated device tree bindings documentation for edge-rate
> - The edge-rate is now specified as a "slowdown", meaning that it is now
>   being specified as positive values instead of negative (both
>   documentation and implementation wise).
> - Only explicitly documented values for "vsc8531,vddmac" and
>   "vsc8531,edge-slowdown" are accepted by the device driver.
> - Deleted include/dt-bindings/net/mscc-phy-vsc8531.h as it was not needed.
> - Read/validate devicetree settings in probe instead of init
> 
> Signed-off-by: Allan W. Nielsen <allan.nielsen@microsemi.com>
> Signed-off-by: Raju Lakkaraju <raju.lakkaraju@microsemi.com>

This doesn't apply cleanly to net-next, please respin.

Thanks.

[PATCH net-next v11 0/1] net: phy: Cleanup the Edge-Rate feature in Microsemi PHYs (rebase)

[Allan W. Nielsen]

Hi,

On 13/10/16 10:01, David Miller wrote:
> This doesn't apply cleanly to net-next, please respin.
Sorry about that... But, I have already send a rebased version (v11) which does
apply cleanly. This time I will try and see if I can get git-send-email to use
the same thread ID.

Anyway, here is a re-post of version 11 (which should apply cleanly on-top of
net-next)

v10 was reviewed by Florian and Andrew:

On 12/10/16 02:14, Florian Fainelli wrote:
> On 10/10/2016 07:13 AM, Allan W. Nielsen wrote:
> > Edge-Rate cleanup include the following:
> > ...
> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>

On 11/10/16 15:09, Andrew Lunn wrote:
> On Mon, Oct 10, 2016 at 04:13:45PM +0200, Allan W. Nielsen wrote:
> > Edge-Rate cleanup include the following:
> > ...
> Reviewed-by: Andrew Lunn <andrew@lunn.ch>

Best regards
Allan W. Nielsen

[PATCH net-next v11 1/1] net: phy: Cleanup the Edge-Rate feature in Microsemi PHYs.

[Allan W. Nielsen]

Edge-Rate cleanup include the following:
- Updated device tree bindings documentation for edge-rate
- The edge-rate is now specified as a "slowdown", meaning that it is now
  being specified as positive values instead of negative (both
  documentation and implementation wise).
- Only explicitly documented values for "vsc8531,vddmac" and
  "vsc8531,edge-slowdown" are accepted by the device driver.
- Deleted include/dt-bindings/net/mscc-phy-vsc8531.h as it was not needed.
- Read/validate devicetree settings in probe instead of init

Signed-off-by: Allan W. Nielsen <allan.nielsen@microsemi.com>
Signed-off-by: Raju Lakkaraju <raju.lakkaraju@microsemi.com>
---
 .../devicetree/bindings/net/mscc-phy-vsc8531.txt   |  51 ++++----
 drivers/net/phy/mscc.c                             | 135 ++++++++++-----------
 include/dt-bindings/net/mscc-phy-vsc8531.h         |  21 ----
 3 files changed, 90 insertions(+), 117 deletions(-)
 delete mode 100644 include/dt-bindings/net/mscc-phy-vsc8531.h

diff --git a/Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt b/Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt
index 99c7eb0..bdefefc6 100644
--- a/Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt
+++ b/Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt
@@ -6,22 +6,27 @@ Required properties:
 		  Documentation/devicetree/bindings/net/phy.txt
 
 Optional properties:
-- vsc8531,vddmac	: The vddmac in mV.
+- vsc8531,vddmac	: The vddmac in mV. Allowed values is listed
+			  in the first row of Table 1 (below).
+			  This property is only used in combination
+			  with the 'edge-slowdown' property.
+			  Default value is 3300.
 - vsc8531,edge-slowdown	: % the edge should be slowed down relative to
-			  the fastest possible edge time. Native sign
-			  need not enter.
+			  the fastest possible edge time.
 			  Edge rate sets the drive strength of the MAC
-			  interface output signals.  Changing the drive
-			  strength will affect the edge rate of the output
-			  signal.  The goal of this setting is to help
-			  reduce electrical emission (EMI) by being able
-			  to reprogram drive strength and in effect slow
-			  down the edge rate if desired.  Table 1 shows the
-			  impact to the edge rate per VDDMAC supply for each
-			  drive strength setting.
-			  Ref: Table:1 - Edge rate change below.
-
-Note: see dt-bindings/net/mscc-phy-vsc8531.h for applicable values
+			  interface output signals.  Changing the
+			  drive strength will affect the edge rate of
+			  the output signal.  The goal of this setting
+			  is to help reduce electrical emission (EMI)
+			  by being able to reprogram drive strength
+			  and in effect slow down the edge rate if
+			  desired.
+			  To adjust the edge-slowdown, the 'vddmac'
+			  must be specified. Table 1 lists the
+			  supported edge-slowdown values for a given
+			  'vddmac'.
+			  Default value is 0%.
+			  Ref: Table:1 - Edge rate change (below).
 
 Table: 1 - Edge rate change
 ----------------------------------------------------------------|
@@ -29,23 +34,23 @@ Table: 1 - Edge rate change
 |								|
 | 3300 mV	2500 mV		1800 mV		1500 mV		|
 |---------------------------------------------------------------|
-| Default	Deafult		Default		Default		|
+| 0%		0%		0%		0%		|
 | (Fastest)			(recommended)	(recommended)	|
 |---------------------------------------------------------------|
-| -2%		-3%		-5%		-6%		|
+| 2%		3%		5%		6%		|
 |---------------------------------------------------------------|
-| -4%		-6%		-9%		-14%		|
+| 4%		6%		9%		14%		|
 |---------------------------------------------------------------|
-| -7%		-10%		-16%		-21%		|
+| 7%		10%		16%		21%		|
 |(recommended)	(recommended)					|
 |---------------------------------------------------------------|
-| -10%		-14%		-23%		-29%		|
+| 10%		14%		23%		29%		|
 |---------------------------------------------------------------|
-| -17%		-23%		-35%		-42%		|
+| 17%		23%		35%		42%		|
 |---------------------------------------------------------------|
-| -29%		-37%		-52%		-58%		|
+| 29%		37%		52%		58%		|
 |---------------------------------------------------------------|
-| -53%		-63%		-76%		-77%		|
+| 53%		63%		76%		77%		|
 | (slowest)							|
 |---------------------------------------------------------------|
 
@@ -54,5 +59,5 @@ Example:
         vsc8531_0: ethernet-phy@0 {
                 compatible = "ethernet-phy-id0007.0570";
                 vsc8531,vddmac		= <3300>;
-                vsc8531,edge-slowdown	= <21>;
+                vsc8531,edge-slowdown	= <7>;
         };
diff --git a/drivers/net/phy/mscc.c b/drivers/net/phy/mscc.c
index 77a6671..113616b 100644
--- a/drivers/net/phy/mscc.c
+++ b/drivers/net/phy/mscc.c
@@ -12,7 +12,6 @@
 #include <linux/mii.h>
 #include <linux/phy.h>
 #include <linux/of.h>
-#include <dt-bindings/net/mscc-phy-vsc8531.h>
 #include <linux/netdevice.h>
 
 enum rgmii_rx_clock_delay {
@@ -69,23 +68,29 @@ enum rgmii_rx_clock_delay {
 #define PHY_ID_VSC8531			  0x00070570
 #define PHY_ID_VSC8541			  0x00070770
 
-struct edge_rate_table {
-	u16 vddmac;
-	int slowdown[MSCC_SLOWDOWN_MAX];
-};
+#define MSCC_VDDMAC_1500		  1500
+#define MSCC_VDDMAC_1800		  1800
+#define MSCC_VDDMAC_2500		  2500
+#define MSCC_VDDMAC_3300		  3300
 
-struct edge_rate_table edge_table[MSCC_VDDMAC_MAX] = {
-	{3300, { 0, -2, -4,  -7,  -10, -17, -29, -53} },
-	{2500, { 0, -3, -6,  -10, -14, -23, -37, -63} },
-	{1800, { 0, -5, -9,  -16, -23, -35, -52, -76} },
-	{1500, { 0, -6, -14, -21, -29, -42, -58, -77} },
+struct vsc8531_private {
+	int rate_magic;
 };
 
-struct vsc8531_private {
-	u8 edge_slowdown;
+#ifdef CONFIG_OF_MDIO
+struct vsc8531_edge_rate_table {
 	u16 vddmac;
+	u8 slowdown[8];
 };
 
+static const struct vsc8531_edge_rate_table edge_table[] = {
+	{MSCC_VDDMAC_3300, { 0, 2,  4,  7, 10, 17, 29, 53} },
+	{MSCC_VDDMAC_2500, { 0, 3,  6, 10, 14, 23, 37, 63} },
+	{MSCC_VDDMAC_1800, { 0, 5,  9, 16, 23, 35, 52, 76} },
+	{MSCC_VDDMAC_1500, { 0, 6, 14, 21, 29, 42, 58, 77} },
+};
+#endif /* CONFIG_OF_MDIO */
+
 static int vsc85xx_phy_page_set(struct phy_device *phydev, u8 page)
 {
 	int rc;
@@ -205,29 +210,43 @@ static void vsc85xx_wol_get(struct phy_device *phydev,
 	mutex_unlock(&phydev->lock);
 }
 
-static u8 edge_rate_magic_get(u16 vddmac,
-			      int slowdown)
+#ifdef CONFIG_OF_MDIO
+static int vsc85xx_edge_rate_magic_get(struct phy_device *phydev)
 {
-	int rc = (MSCC_SLOWDOWN_MAX - 1);
-	u8 vdd;
 	u8 sd;
+	u16 vdd;
+	int rc, i, j;
+	struct device *dev = &phydev->mdio.dev;
+	struct device_node *of_node = dev->of_node;
+	u8 sd_array_size = ARRAY_SIZE(edge_table[0].slowdown);
 
-	for (vdd = 0; vdd < MSCC_VDDMAC_MAX; vdd++) {
-		if (edge_table[vdd].vddmac == vddmac) {
-			for (sd = 0; sd < MSCC_SLOWDOWN_MAX; sd++) {
-				if (edge_table[vdd].slowdown[sd] <= slowdown) {
-					rc = (MSCC_SLOWDOWN_MAX - sd - 1);
-					break;
-				}
-			}
-		}
-	}
+	if (!of_node)
+		return -ENODEV;
 
-	return rc;
+	rc = of_property_read_u16(of_node, "vsc8531,vddmac", &vdd);
+	if (rc != 0)
+		vdd = MSCC_VDDMAC_3300;
+
+	rc = of_property_read_u8(of_node, "vsc8531,edge-slowdown", &sd);
+	if (rc != 0)
+		sd = 0;
+
+	for (i = 0; i < ARRAY_SIZE(edge_table); i++)
+		if (edge_table[i].vddmac == vdd)
+			for (j = 0; j < sd_array_size; j++)
+				if (edge_table[i].slowdown[j] == sd)
+					return (sd_array_size - j - 1);
+
+	return -EINVAL;
+}
+#else
+static int vsc85xx_edge_rate_magic_get(struct phy_device *phydev)
+{
+	return 0;
 }
+#endif /* CONFIG_OF_MDIO */
 
-static int vsc85xx_edge_rate_cntl_set(struct phy_device *phydev,
-				      u8 edge_rate)
+static int vsc85xx_edge_rate_cntl_set(struct phy_device *phydev, u8 edge_rate)
 {
 	int rc;
 	u16 reg_val;
@@ -308,45 +327,10 @@ static int vsc85xx_default_config(struct phy_device *phydev)
 	return rc;
 }
 
-#ifdef CONFIG_OF_MDIO
-static int vsc8531_of_init(struct phy_device *phydev)
-{
-	int rc;
-	struct vsc8531_private *vsc8531 = phydev->priv;
-	struct device *dev = &phydev->mdio.dev;
-	struct device_node *of_node = dev->of_node;
-
-	if (!of_node)
-		return -ENODEV;
-
-	rc = of_property_read_u16(of_node, "vsc8531,vddmac",
-				  &vsc8531->vddmac);
-	if (rc == -EINVAL)
-		vsc8531->vddmac = MSCC_VDDMAC_3300;
-	rc = of_property_read_u8(of_node, "vsc8531,edge-slowdown",
-				 &vsc8531->edge_slowdown);
-	if (rc == -EINVAL)
-		vsc8531->edge_slowdown = 0;
-
-	rc = 0;
-	return rc;
-}
-#else
-static int vsc8531_of_init(struct phy_device *phydev)
-{
-	return 0;
-}
-#endif /* CONFIG_OF_MDIO */
-
 static int vsc85xx_config_init(struct phy_device *phydev)
 {
 	int rc;
 	struct vsc8531_private *vsc8531 = phydev->priv;
-	u8 edge_rate;
-
-	rc = vsc8531_of_init(phydev);
-	if (rc)
-		return rc;
 
 	rc = vsc85xx_default_config(phydev);
 	if (rc)
@@ -356,9 +340,7 @@ static int vsc85xx_config_init(struct phy_device *phydev)
 	if (rc)
 		return rc;
 
-	edge_rate = edge_rate_magic_get(vsc8531->vddmac,
-					-(int)vsc8531->edge_slowdown);
-	rc = vsc85xx_edge_rate_cntl_set(phydev, edge_rate);
+	rc = vsc85xx_edge_rate_cntl_set(phydev, vsc8531->rate_magic);
 	if (rc)
 		return rc;
 
@@ -396,14 +378,21 @@ static int vsc85xx_config_intr(struct phy_device *phydev)
 
 static int vsc85xx_probe(struct phy_device *phydev)
 {
+	int rate_magic;
 	struct vsc8531_private *vsc8531;
 
+	rate_magic = vsc85xx_edge_rate_magic_get(phydev);
+	if (rate_magic < 0)
+		return rate_magic;
+
 	vsc8531 = devm_kzalloc(&phydev->mdio.dev, sizeof(*vsc8531), GFP_KERNEL);
 	if (!vsc8531)
 		return -ENOMEM;
 
 	phydev->priv = vsc8531;
 
+	vsc8531->rate_magic = rate_magic;
+
 	return 0;
 }
 
@@ -424,9 +413,9 @@ static struct phy_driver vsc85xx_driver[] = {
 	.config_intr    = &vsc85xx_config_intr,
 	.suspend	= &genphy_suspend,
 	.resume		= &genphy_resume,
-	.probe          = &vsc85xx_probe,
-	.set_wol        = &vsc85xx_wol_set,
-	.get_wol        = &vsc85xx_wol_get,
+	.probe		= &vsc85xx_probe,
+	.set_wol	= &vsc85xx_wol_set,
+	.get_wol	= &vsc85xx_wol_get,
 },
 {
 	.phy_id		= PHY_ID_VSC8541,
@@ -443,9 +432,9 @@ static struct phy_driver vsc85xx_driver[] = {
 	.config_intr    = &vsc85xx_config_intr,
 	.suspend	= &genphy_suspend,
 	.resume		= &genphy_resume,
-	.probe          = &vsc85xx_probe,
-	.set_wol        = &vsc85xx_wol_set,
-	.get_wol        = &vsc85xx_wol_get,
+	.probe		= &vsc85xx_probe,
+	.set_wol	= &vsc85xx_wol_set,
+	.get_wol	= &vsc85xx_wol_get,
 }
 
 };
diff --git a/include/dt-bindings/net/mscc-phy-vsc8531.h b/include/dt-bindings/net/mscc-phy-vsc8531.h
deleted file mode 100644
index 2383dd2..0000000
--- a/include/dt-bindings/net/mscc-phy-vsc8531.h
+++ /dev/null
@@ -1,21 +0,0 @@
-/*
- * Device Tree constants for Microsemi VSC8531 PHY
- *
- * Author: Nagaraju Lakkaraju
- *
- * License: Dual MIT/GPL
- * Copyright (c) 2016 Microsemi Corporation
- */
-
-#ifndef _DT_BINDINGS_MSCC_VSC8531_H
-#define _DT_BINDINGS_MSCC_VSC8531_H
-
-/* MAC interface Edge rate control VDDMAC in milli Volts */
-#define MSCC_VDDMAC_3300		 3300
-#define MSCC_VDDMAC_2500		 2500
-#define MSCC_VDDMAC_1800		 1800
-#define MSCC_VDDMAC_1500		 1500
-#define MSCC_VDDMAC_MAX			 4
-#define MSCC_SLOWDOWN_MAX		 8
-
-#endif
-- 
2.7.3

Re: [PATCH net-next v11 1/1] net: phy: Cleanup the Edge-Rate feature in Microsemi PHYs.

[David Miller]

From: "Allan W. Nielsen" <allan.nielsen@microsemi.com>
Date: Thu, 13 Oct 2016 20:21:30 +0200

> Edge-Rate cleanup include the following:
> - Updated device tree bindings documentation for edge-rate
> - The edge-rate is now specified as a "slowdown", meaning that it is now
>   being specified as positive values instead of negative (both
>   documentation and implementation wise).
> - Only explicitly documented values for "vsc8531,vddmac" and
>   "vsc8531,edge-slowdown" are accepted by the device driver.
> - Deleted include/dt-bindings/net/mscc-phy-vsc8531.h as it was not needed.
> - Read/validate devicetree settings in probe instead of init
> 
> Signed-off-by: Allan W. Nielsen <allan.nielsen@microsemi.com>
> Signed-off-by: Raju Lakkaraju <raju.lakkaraju@microsemi.com>

This patch does not apply to the net-next tree.

Take my tree, put this email of your's into a file, and run this:

bash$ git am file

and you will get:

[davem@dhcp-10-15-49-210 net-next]$ git am --signoff net-next-v11-1-1-net-phy-Cleanup-the-Edge-Rate-feature-in-Microsemi-PHYs..patch 
Applying: net: phy: Cleanup the Edge-Rate feature in Microsemi PHYs.
error: patch failed: Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt:6
error: Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt: patch does not apply
error: patch failed: drivers/net/phy/mscc.c:12
error: drivers/net/phy/mscc.c: patch does not apply
error: include/dt-bindings/net/mscc-phy-vsc8531.h: does not exist in index
Patch failed at 0001 net: phy: Cleanup the Edge-Rate feature in Microsemi PHYs.
The copy of the patch that failed is found in:
   /home/davem/src/GIT/net-next/.git/rebase-apply/patch
When you have resolved this problem, run "git am --continue".
If you prefer to skip this patch, run "git am --skip" instead.
To restore the original branch and stop patching, run "git am --abort".

Please do not resubmit this patch until you can successfully email the
patch to yourself and apply it cleanly to the net-next tree.

Re: [PATCH net-next v11 1/1] net: phy: Cleanup the Edge-Rate feature in Microsemi PHYs.

[Allan W. Nielsen]

Hi David,

I'm really sorry if I messed up, or is not following the protocol...

But you have applied it already:
http://git.kernel.org/cgit/linux/kernel/git/davem/net-next.git/commit/?id=4f58e6dceb0e44ca8f21568ed81e1df24e55964c

> commit 4f58e6dceb0e44ca8f21568ed81e1df24e55964c
> Author:     Allan W. Nielsen <allan.nielsen@microsemi.com>
> AuthorDate: Wed Oct 12 15:47:51 2016 +0200
> Commit:     David S. Miller <davem@davemloft.net>
> CommitDate: Fri Oct 14 10:06:13 2016 -0400
> 
>     net: phy: Cleanup the Edge-Rate feature in Microsemi PHYs.
> 
>     Edge-Rate cleanup include the following:
>     - Updated device tree bindings documentation for edge-rate
>     - The edge-rate is now specified as a "slowdown", meaning that it is now
>       being specified as positive values instead of negative (both
>       documentation and implementation wise).
>     - Only explicitly documented values for "vsc8531,vddmac" and
>       "vsc8531,edge-slowdown" are accepted by the device driver.
>     - Deleted include/dt-bindings/net/mscc-phy-vsc8531.h as it was not needed.
>     - Read/validate devicetree settings in probe instead of init
> 
>     Signed-off-by: Allan W. Nielsen <allan.nielsen@microsemi.com>
>     Signed-off-by: Raju Lakkaraju <raju.lakkaraju@microsemi.com>
>     Signed-off-by: David S. Miller <davem@davemloft.net>

Maybe the misunderstanding was caused by me posting the re-based version in
another thread.

Anyway, thanks a lot for the big effort you put into maintaining this
sub-system. I will be more care full next time to avoid such confusions.

Best regards
Allan W. Nielsen





On 14/10/16 11:05, David Miller wrote:
> EXTERNAL EMAIL
> 
> 
> From: "Allan W. Nielsen" <allan.nielsen@microsemi.com>
> Date: Thu, 13 Oct 2016 20:21:30 +0200
> 
> > Edge-Rate cleanup include the following:
> > - Updated device tree bindings documentation for edge-rate
> > - The edge-rate is now specified as a "slowdown", meaning that it is now
> >   being specified as positive values instead of negative (both
> >   documentation and implementation wise).
> > - Only explicitly documented values for "vsc8531,vddmac" and
> >   "vsc8531,edge-slowdown" are accepted by the device driver.
> > - Deleted include/dt-bindings/net/mscc-phy-vsc8531.h as it was not needed.
> > - Read/validate devicetree settings in probe instead of init
> >
> > Signed-off-by: Allan W. Nielsen <allan.nielsen@microsemi.com>
> > Signed-off-by: Raju Lakkaraju <raju.lakkaraju@microsemi.com>
> 
> This patch does not apply to the net-next tree.
> 
> Take my tree, put this email of your's into a file, and run this:
> 
> bash$ git am file
> 
> and you will get:
> 
> [davem@dhcp-10-15-49-210 net-next]$ git am --signoff net-next-v11-1-1-net-phy-Cleanup-the-Edge-Rate-feature-in-Microsemi-PHYs..patch
> Applying: net: phy: Cleanup the Edge-Rate feature in Microsemi PHYs.
> error: patch failed: Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt:6
> error: Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt: patch does not apply
> error: patch failed: drivers/net/phy/mscc.c:12
> error: drivers/net/phy/mscc.c: patch does not apply
> error: include/dt-bindings/net/mscc-phy-vsc8531.h: does not exist in index
> Patch failed at 0001 net: phy: Cleanup the Edge-Rate feature in Microsemi PHYs.
> The copy of the patch that failed is found in:
>    /home/davem/src/GIT/net-next/.git/rebase-apply/patch
> When you have resolved this problem, run "git am --continue".
> If you prefer to skip this patch, run "git am --skip" instead.
> To restore the original branch and stop patching, run "git am --abort".
> 
> Please do not resubmit this patch until you can successfully email the
> patch to yourself and apply it cleanly to the net-next tree.
> 
> 

[PATCH net-next v11 0/1] net: phy: Rebase Edge-Rate clean up

[Allan W. Nielsen]

Hi,

I can see that the "Add Wake-on-LAN driver for Microsemi PHYs" (0a55c12f97)
patch has been applied to net-next, and that it is causing the Edge-Rate patch
to conflict.

I have therefore rebased v10 of the patch to fit on top of net-next.

/Allan

-- 
2.7.3

[PATCH net-next v11 1/1] net: phy: Cleanup the Edge-Rate feature in Microsemi PHYs.

[Allan W. Nielsen]

Edge-Rate cleanup include the following:
- Updated device tree bindings documentation for edge-rate
- The edge-rate is now specified as a "slowdown", meaning that it is now
  being specified as positive values instead of negative (both
  documentation and implementation wise).
- Only explicitly documented values for "vsc8531,vddmac" and
  "vsc8531,edge-slowdown" are accepted by the device driver.
- Deleted include/dt-bindings/net/mscc-phy-vsc8531.h as it was not needed.
- Read/validate devicetree settings in probe instead of init

Signed-off-by: Allan W. Nielsen <allan.nielsen@microsemi.com>
Signed-off-by: Raju Lakkaraju <raju.lakkaraju@microsemi.com>
---
 .../devicetree/bindings/net/mscc-phy-vsc8531.txt   |  51 ++++----
 drivers/net/phy/mscc.c                             | 135 ++++++++++-----------
 include/dt-bindings/net/mscc-phy-vsc8531.h         |  21 ----
 3 files changed, 90 insertions(+), 117 deletions(-)
 delete mode 100644 include/dt-bindings/net/mscc-phy-vsc8531.h

diff --git a/Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt b/Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt
index 99c7eb0..bdefefc6 100644
--- a/Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt
+++ b/Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt
@@ -6,22 +6,27 @@ Required properties:
 		  Documentation/devicetree/bindings/net/phy.txt
 
 Optional properties:
-- vsc8531,vddmac	: The vddmac in mV.
+- vsc8531,vddmac	: The vddmac in mV. Allowed values is listed
+			  in the first row of Table 1 (below).
+			  This property is only used in combination
+			  with the 'edge-slowdown' property.
+			  Default value is 3300.
 - vsc8531,edge-slowdown	: % the edge should be slowed down relative to
-			  the fastest possible edge time. Native sign
-			  need not enter.
+			  the fastest possible edge time.
 			  Edge rate sets the drive strength of the MAC
-			  interface output signals.  Changing the drive
-			  strength will affect the edge rate of the output
-			  signal.  The goal of this setting is to help
-			  reduce electrical emission (EMI) by being able
-			  to reprogram drive strength and in effect slow
-			  down the edge rate if desired.  Table 1 shows the
-			  impact to the edge rate per VDDMAC supply for each
-			  drive strength setting.
-			  Ref: Table:1 - Edge rate change below.
-
-Note: see dt-bindings/net/mscc-phy-vsc8531.h for applicable values
+			  interface output signals.  Changing the
+			  drive strength will affect the edge rate of
+			  the output signal.  The goal of this setting
+			  is to help reduce electrical emission (EMI)
+			  by being able to reprogram drive strength
+			  and in effect slow down the edge rate if
+			  desired.
+			  To adjust the edge-slowdown, the 'vddmac'
+			  must be specified. Table 1 lists the
+			  supported edge-slowdown values for a given
+			  'vddmac'.
+			  Default value is 0%.
+			  Ref: Table:1 - Edge rate change (below).
 
 Table: 1 - Edge rate change
 ----------------------------------------------------------------|
@@ -29,23 +34,23 @@ Table: 1 - Edge rate change
 |								|
 | 3300 mV	2500 mV		1800 mV		1500 mV		|
 |---------------------------------------------------------------|
-| Default	Deafult		Default		Default		|
+| 0%		0%		0%		0%		|
 | (Fastest)			(recommended)	(recommended)	|
 |---------------------------------------------------------------|
-| -2%		-3%		-5%		-6%		|
+| 2%		3%		5%		6%		|
 |---------------------------------------------------------------|
-| -4%		-6%		-9%		-14%		|
+| 4%		6%		9%		14%		|
 |---------------------------------------------------------------|
-| -7%		-10%		-16%		-21%		|
+| 7%		10%		16%		21%		|
 |(recommended)	(recommended)					|
 |---------------------------------------------------------------|
-| -10%		-14%		-23%		-29%		|
+| 10%		14%		23%		29%		|
 |---------------------------------------------------------------|
-| -17%		-23%		-35%		-42%		|
+| 17%		23%		35%		42%		|
 |---------------------------------------------------------------|
-| -29%		-37%		-52%		-58%		|
+| 29%		37%		52%		58%		|
 |---------------------------------------------------------------|
-| -53%		-63%		-76%		-77%		|
+| 53%		63%		76%		77%		|
 | (slowest)							|
 |---------------------------------------------------------------|
 
@@ -54,5 +59,5 @@ Example:
         vsc8531_0: ethernet-phy@0 {
                 compatible = "ethernet-phy-id0007.0570";
                 vsc8531,vddmac		= <3300>;
-                vsc8531,edge-slowdown	= <21>;
+                vsc8531,edge-slowdown	= <7>;
         };
diff --git a/drivers/net/phy/mscc.c b/drivers/net/phy/mscc.c
index 77a6671..113616b 100644
--- a/drivers/net/phy/mscc.c
+++ b/drivers/net/phy/mscc.c
@@ -12,7 +12,6 @@
 #include <linux/mii.h>
 #include <linux/phy.h>
 #include <linux/of.h>
-#include <dt-bindings/net/mscc-phy-vsc8531.h>
 #include <linux/netdevice.h>
 
 enum rgmii_rx_clock_delay {
@@ -69,23 +68,29 @@ enum rgmii_rx_clock_delay {
 #define PHY_ID_VSC8531			  0x00070570
 #define PHY_ID_VSC8541			  0x00070770
 
-struct edge_rate_table {
-	u16 vddmac;
-	int slowdown[MSCC_SLOWDOWN_MAX];
-};
+#define MSCC_VDDMAC_1500		  1500
+#define MSCC_VDDMAC_1800		  1800
+#define MSCC_VDDMAC_2500		  2500
+#define MSCC_VDDMAC_3300		  3300
 
-struct edge_rate_table edge_table[MSCC_VDDMAC_MAX] = {
-	{3300, { 0, -2, -4,  -7,  -10, -17, -29, -53} },
-	{2500, { 0, -3, -6,  -10, -14, -23, -37, -63} },
-	{1800, { 0, -5, -9,  -16, -23, -35, -52, -76} },
-	{1500, { 0, -6, -14, -21, -29, -42, -58, -77} },
+struct vsc8531_private {
+	int rate_magic;
 };
 
-struct vsc8531_private {
-	u8 edge_slowdown;
+#ifdef CONFIG_OF_MDIO
+struct vsc8531_edge_rate_table {
 	u16 vddmac;
+	u8 slowdown[8];
 };
 
+static const struct vsc8531_edge_rate_table edge_table[] = {
+	{MSCC_VDDMAC_3300, { 0, 2,  4,  7, 10, 17, 29, 53} },
+	{MSCC_VDDMAC_2500, { 0, 3,  6, 10, 14, 23, 37, 63} },
+	{MSCC_VDDMAC_1800, { 0, 5,  9, 16, 23, 35, 52, 76} },
+	{MSCC_VDDMAC_1500, { 0, 6, 14, 21, 29, 42, 58, 77} },
+};
+#endif /* CONFIG_OF_MDIO */
+
 static int vsc85xx_phy_page_set(struct phy_device *phydev, u8 page)
 {
 	int rc;
@@ -205,29 +210,43 @@ static void vsc85xx_wol_get(struct phy_device *phydev,
 	mutex_unlock(&phydev->lock);
 }
 
-static u8 edge_rate_magic_get(u16 vddmac,
-			      int slowdown)
+#ifdef CONFIG_OF_MDIO
+static int vsc85xx_edge_rate_magic_get(struct phy_device *phydev)
 {
-	int rc = (MSCC_SLOWDOWN_MAX - 1);
-	u8 vdd;
 	u8 sd;
+	u16 vdd;
+	int rc, i, j;
+	struct device *dev = &phydev->mdio.dev;
+	struct device_node *of_node = dev->of_node;
+	u8 sd_array_size = ARRAY_SIZE(edge_table[0].slowdown);
 
-	for (vdd = 0; vdd < MSCC_VDDMAC_MAX; vdd++) {
-		if (edge_table[vdd].vddmac == vddmac) {
-			for (sd = 0; sd < MSCC_SLOWDOWN_MAX; sd++) {
-				if (edge_table[vdd].slowdown[sd] <= slowdown) {
-					rc = (MSCC_SLOWDOWN_MAX - sd - 1);
-					break;
-				}
-			}
-		}
-	}
+	if (!of_node)
+		return -ENODEV;
 
-	return rc;
+	rc = of_property_read_u16(of_node, "vsc8531,vddmac", &vdd);
+	if (rc != 0)
+		vdd = MSCC_VDDMAC_3300;
+
+	rc = of_property_read_u8(of_node, "vsc8531,edge-slowdown", &sd);
+	if (rc != 0)
+		sd = 0;
+
+	for (i = 0; i < ARRAY_SIZE(edge_table); i++)
+		if (edge_table[i].vddmac == vdd)
+			for (j = 0; j < sd_array_size; j++)
+				if (edge_table[i].slowdown[j] == sd)
+					return (sd_array_size - j - 1);
+
+	return -EINVAL;
+}
+#else
+static int vsc85xx_edge_rate_magic_get(struct phy_device *phydev)
+{
+	return 0;
 }
+#endif /* CONFIG_OF_MDIO */
 
-static int vsc85xx_edge_rate_cntl_set(struct phy_device *phydev,
-				      u8 edge_rate)
+static int vsc85xx_edge_rate_cntl_set(struct phy_device *phydev, u8 edge_rate)
 {
 	int rc;
 	u16 reg_val;
@@ -308,45 +327,10 @@ static int vsc85xx_default_config(struct phy_device *phydev)
 	return rc;
 }
 
-#ifdef CONFIG_OF_MDIO
-static int vsc8531_of_init(struct phy_device *phydev)
-{
-	int rc;
-	struct vsc8531_private *vsc8531 = phydev->priv;
-	struct device *dev = &phydev->mdio.dev;
-	struct device_node *of_node = dev->of_node;
-
-	if (!of_node)
-		return -ENODEV;
-
-	rc = of_property_read_u16(of_node, "vsc8531,vddmac",
-				  &vsc8531->vddmac);
-	if (rc == -EINVAL)
-		vsc8531->vddmac = MSCC_VDDMAC_3300;
-	rc = of_property_read_u8(of_node, "vsc8531,edge-slowdown",
-				 &vsc8531->edge_slowdown);
-	if (rc == -EINVAL)
-		vsc8531->edge_slowdown = 0;
-
-	rc = 0;
-	return rc;
-}
-#else
-static int vsc8531_of_init(struct phy_device *phydev)
-{
-	return 0;
-}
-#endif /* CONFIG_OF_MDIO */
-
 static int vsc85xx_config_init(struct phy_device *phydev)
 {
 	int rc;
 	struct vsc8531_private *vsc8531 = phydev->priv;
-	u8 edge_rate;
-
-	rc = vsc8531_of_init(phydev);
-	if (rc)
-		return rc;
 
 	rc = vsc85xx_default_config(phydev);
 	if (rc)
@@ -356,9 +340,7 @@ static int vsc85xx_config_init(struct phy_device *phydev)
 	if (rc)
 		return rc;
 
-	edge_rate = edge_rate_magic_get(vsc8531->vddmac,
-					-(int)vsc8531->edge_slowdown);
-	rc = vsc85xx_edge_rate_cntl_set(phydev, edge_rate);
+	rc = vsc85xx_edge_rate_cntl_set(phydev, vsc8531->rate_magic);
 	if (rc)
 		return rc;
 
@@ -396,14 +378,21 @@ static int vsc85xx_config_intr(struct phy_device *phydev)
 
 static int vsc85xx_probe(struct phy_device *phydev)
 {
+	int rate_magic;
 	struct vsc8531_private *vsc8531;
 
+	rate_magic = vsc85xx_edge_rate_magic_get(phydev);
+	if (rate_magic < 0)
+		return rate_magic;
+
 	vsc8531 = devm_kzalloc(&phydev->mdio.dev, sizeof(*vsc8531), GFP_KERNEL);
 	if (!vsc8531)
 		return -ENOMEM;
 
 	phydev->priv = vsc8531;
 
+	vsc8531->rate_magic = rate_magic;
+
 	return 0;
 }
 
@@ -424,9 +413,9 @@ static struct phy_driver vsc85xx_driver[] = {
 	.config_intr    = &vsc85xx_config_intr,
 	.suspend	= &genphy_suspend,
 	.resume		= &genphy_resume,
-	.probe          = &vsc85xx_probe,
-	.set_wol        = &vsc85xx_wol_set,
-	.get_wol        = &vsc85xx_wol_get,
+	.probe		= &vsc85xx_probe,
+	.set_wol	= &vsc85xx_wol_set,
+	.get_wol	= &vsc85xx_wol_get,
 },
 {
 	.phy_id		= PHY_ID_VSC8541,
@@ -443,9 +432,9 @@ static struct phy_driver vsc85xx_driver[] = {
 	.config_intr    = &vsc85xx_config_intr,
 	.suspend	= &genphy_suspend,
 	.resume		= &genphy_resume,
-	.probe          = &vsc85xx_probe,
-	.set_wol        = &vsc85xx_wol_set,
-	.get_wol        = &vsc85xx_wol_get,
+	.probe		= &vsc85xx_probe,
+	.set_wol	= &vsc85xx_wol_set,
+	.get_wol	= &vsc85xx_wol_get,
 }
 
 };
diff --git a/include/dt-bindings/net/mscc-phy-vsc8531.h b/include/dt-bindings/net/mscc-phy-vsc8531.h
deleted file mode 100644
index 2383dd2..0000000
--- a/include/dt-bindings/net/mscc-phy-vsc8531.h
+++ /dev/null
@@ -1,21 +0,0 @@
-/*
- * Device Tree constants for Microsemi VSC8531 PHY
- *
- * Author: Nagaraju Lakkaraju
- *
- * License: Dual MIT/GPL
- * Copyright (c) 2016 Microsemi Corporation
- */
-
-#ifndef _DT_BINDINGS_MSCC_VSC8531_H
-#define _DT_BINDINGS_MSCC_VSC8531_H
-
-/* MAC interface Edge rate control VDDMAC in milli Volts */
-#define MSCC_VDDMAC_3300		 3300
-#define MSCC_VDDMAC_2500		 2500
-#define MSCC_VDDMAC_1800		 1800
-#define MSCC_VDDMAC_1500		 1500
-#define MSCC_VDDMAC_MAX			 4
-#define MSCC_SLOWDOWN_MAX		 8
-
-#endif
-- 
2.7.3