* [PATCH v9 0/2] Add a new board TOPEET iTOP for Exynos 4412 [not found] <devicetree@vger.kernel.org> 2016-10-18 17:18 ` Randy Li @ 2016-10-18 17:18 ` Randy Li 0 siblings, 0 replies; 23+ messages in thread From: Randy Li @ 2016-10-18 17:18 UTC (permalink / raw) To: devicetree-u79uwXL29TY76Z2rM5mHXA Cc: mark.rutland-5wv7dgnIgG8, linux-I+IVW8TIWO2tmTQ+vhA3Yw, kgene-DgEjT+Ai2ygdnm+yROfE0A, krzk-DgEjT+Ai2ygdnm+yROfE0A, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, linux-samsung-soc-u79uwXL29TY76Z2rM5mHXA, linux-kernel-u79uwXL29TY76Z2rM5mHXA, robh-DgEjT+Ai2ygdnm+yROfE0A, Randy Li Changelog: - v9: - fix some warnings. - use the new pin defined for pinctrl. - v8: - add the missing LDOs for PMIC, the pins for LDOs are not avaiabled in core board. - re-order the header files in core board. - skip the vendor prefix file - v7: - add a missing header file - add a rootdelay to bootargs or it can't mount root filesystem - fix the memory node - v6: - move pwms pinctrl to pwms node - fix the order of the dtb file in Makefile - v5: - correct the mail format - v4: - re-order some nodes in alphabetical order - fix some minor bugs - add a entry in vendor list - v3: - fixing the rtc clock, using clock source from PMIC - enable the tmu - enable the fimc for elite board - suuport the audio codec at elite board, but the audio sound a little distortion - fixing minor bugs in the last commit - v2: - removing rtc node the clock source driver is not done yet. - adding exynos-bus - fixing the MFC Randy Li (2): ARM: dts: Add TOPEET itop core board SCP package version ARM: dts: add TOPEET itop elite based board .../bindings/arm/samsung/samsung-boards.txt | 3 + arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/exynos4412-itop-elite.dts | 240 ++++++++++ arch/arm/boot/dts/exynos4412-itop-scp-core.dtsi | 501 +++++++++++++++++++++ 4 files changed, 745 insertions(+) create mode 100644 arch/arm/boot/dts/exynos4412-itop-elite.dts create mode 100644 arch/arm/boot/dts/exynos4412-itop-scp-core.dtsi -- 2.7.4 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 23+ messages in thread
* [PATCH v9 0/2] Add a new board TOPEET iTOP for Exynos 4412 @ 2016-10-18 17:18 ` Randy Li 0 siblings, 0 replies; 23+ messages in thread From: Randy Li @ 2016-10-18 17:18 UTC (permalink / raw) To: devicetree Cc: mark.rutland, linux, kgene, krzk, linux-arm-kernel, linux-samsung-soc, linux-kernel, robh, Randy Li Changelog: - v9: - fix some warnings. - use the new pin defined for pinctrl. - v8: - add the missing LDOs for PMIC, the pins for LDOs are not avaiabled in core board. - re-order the header files in core board. - skip the vendor prefix file - v7: - add a missing header file - add a rootdelay to bootargs or it can't mount root filesystem - fix the memory node - v6: - move pwms pinctrl to pwms node - fix the order of the dtb file in Makefile - v5: - correct the mail format - v4: - re-order some nodes in alphabetical order - fix some minor bugs - add a entry in vendor list - v3: - fixing the rtc clock, using clock source from PMIC - enable the tmu - enable the fimc for elite board - suuport the audio codec at elite board, but the audio sound a little distortion - fixing minor bugs in the last commit - v2: - removing rtc node the clock source driver is not done yet. - adding exynos-bus - fixing the MFC Randy Li (2): ARM: dts: Add TOPEET itop core board SCP package version ARM: dts: add TOPEET itop elite based board .../bindings/arm/samsung/samsung-boards.txt | 3 + arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/exynos4412-itop-elite.dts | 240 ++++++++++ arch/arm/boot/dts/exynos4412-itop-scp-core.dtsi | 501 +++++++++++++++++++++ 4 files changed, 745 insertions(+) create mode 100644 arch/arm/boot/dts/exynos4412-itop-elite.dts create mode 100644 arch/arm/boot/dts/exynos4412-itop-scp-core.dtsi -- 2.7.4 ^ permalink raw reply [flat|nested] 23+ messages in thread
* [PATCH v9 0/2] Add a new board TOPEET iTOP for Exynos 4412 @ 2016-10-18 17:18 ` Randy Li 0 siblings, 0 replies; 23+ messages in thread From: Randy Li @ 2016-10-18 17:18 UTC (permalink / raw) To: linux-arm-kernel Changelog: - v9: - fix some warnings. - use the new pin defined for pinctrl. - v8: - add the missing LDOs for PMIC, the pins for LDOs are not avaiabled in core board. - re-order the header files in core board. - skip the vendor prefix file - v7: - add a missing header file - add a rootdelay to bootargs or it can't mount root filesystem - fix the memory node - v6: - move pwms pinctrl to pwms node - fix the order of the dtb file in Makefile - v5: - correct the mail format - v4: - re-order some nodes in alphabetical order - fix some minor bugs - add a entry in vendor list - v3: - fixing the rtc clock, using clock source from PMIC - enable the tmu - enable the fimc for elite board - suuport the audio codec at elite board, but the audio sound a little distortion - fixing minor bugs in the last commit - v2: - removing rtc node the clock source driver is not done yet. - adding exynos-bus - fixing the MFC Randy Li (2): ARM: dts: Add TOPEET itop core board SCP package version ARM: dts: add TOPEET itop elite based board .../bindings/arm/samsung/samsung-boards.txt | 3 + arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/exynos4412-itop-elite.dts | 240 ++++++++++ arch/arm/boot/dts/exynos4412-itop-scp-core.dtsi | 501 +++++++++++++++++++++ 4 files changed, 745 insertions(+) create mode 100644 arch/arm/boot/dts/exynos4412-itop-elite.dts create mode 100644 arch/arm/boot/dts/exynos4412-itop-scp-core.dtsi -- 2.7.4 ^ permalink raw reply [flat|nested] 23+ messages in thread
[parent not found: <1476811129-4450-1-git-send-email-ayaka-xPW3/0Ywev/iB9QmIjCX8w@public.gmane.org>]
* [PATCH v9 1/2] ARM: dts: Add TOPEET itop core board SCP package version 2016-10-18 17:18 ` Randy Li (?) @ 2016-10-18 17:18 ` Randy Li -1 siblings, 0 replies; 23+ messages in thread From: Randy Li @ 2016-10-18 17:18 UTC (permalink / raw) To: devicetree-u79uwXL29TY76Z2rM5mHXA Cc: mark.rutland-5wv7dgnIgG8, linux-I+IVW8TIWO2tmTQ+vhA3Yw, kgene-DgEjT+Ai2ygdnm+yROfE0A, krzk-DgEjT+Ai2ygdnm+yROfE0A, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, linux-samsung-soc-u79uwXL29TY76Z2rM5mHXA, linux-kernel-u79uwXL29TY76Z2rM5mHXA, robh-DgEjT+Ai2ygdnm+yROfE0A, Randy Li The TOPEET itop is a samsung exnynos 4412 core board, which have two package versions. This patch add the support for SCP version. Currently supported are USB3503A HSIC, USB OTG, eMMC, rtc and PMIC. The future features are in the based board. Also MFC and watchdog have been enabled. Signed-off-by: Randy Li <ayaka-xPW3/0Ywev/iB9QmIjCX8w@public.gmane.org> --- arch/arm/boot/dts/exynos4412-itop-scp-core.dtsi | 501 ++++++++++++++++++++++++ 1 file changed, 501 insertions(+) create mode 100644 arch/arm/boot/dts/exynos4412-itop-scp-core.dtsi diff --git a/arch/arm/boot/dts/exynos4412-itop-scp-core.dtsi b/arch/arm/boot/dts/exynos4412-itop-scp-core.dtsi new file mode 100644 index 0000000..881dc76 --- /dev/null +++ b/arch/arm/boot/dts/exynos4412-itop-scp-core.dtsi @@ -0,0 +1,501 @@ +/* + * TOPEET's Exynos4412 based itop board device tree source + * + * Copyright (c) 2016 SUMOMO Computer Association + * https://www.sumomo.mobi + * Randy Li <ayaka-xPW3/0Ywev/iB9QmIjCX8w@public.gmane.org> + * + * Device tree source file for TOPEET iTop Exynos 4412 SCP package core + * board which is based on Samsung's Exynos4412 SoC. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <dt-bindings/clock/samsung,s2mps11.h> +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include "exynos4412.dtsi" +#include "exynos4412-ppmu-common.dtsi" +#include "exynos-mfc-reserved-memory.dtsi" + +/ { + memory@40000000 { + device_type = "memory"; + reg = <0x40000000 0x40000000>; + }; + + firmware@0203F000 { + compatible = "samsung,secure-firmware"; + reg = <0x0203F000 0x1000>; + }; + + fixed-rate-clocks { + xxti { + compatible = "samsung,clock-xxti"; + clock-frequency = <0>; + }; + + xusbxti { + compatible = "samsung,clock-xusbxti"; + clock-frequency = <24000000>; + }; + }; + + thermal-zones { + cpu_thermal: cpu-thermal { + cooling-maps { + map0 { + /* Corresponds to 800MHz at freq_table */ + cooling-device = <&cpu0 7 7>; + }; + map1 { + /* Corresponds to 200MHz at freq_table */ + cooling-device = <&cpu0 13 13>; + }; + }; + }; + }; + + usb-hub { + compatible = "smsc,usb3503a"; + reset-gpios = <&gpm2 4 GPIO_ACTIVE_LOW>; + connect-gpios = <&gpm3 3 GPIO_ACTIVE_HIGH>; + intn-gpios = <&gpx2 3 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&hsic_reset>; + }; +}; + +&bus_dmc { + devfreq-events = <&ppmu_dmc0_3>, <&ppmu_dmc1_3>; + vdd-supply = <&buck1_reg>; + status = "okay"; +}; + +&bus_acp { + devfreq = <&bus_dmc>; + status = "okay"; +}; + +&bus_c2c { + devfreq = <&bus_dmc>; + status = "okay"; +}; + +&bus_leftbus { + devfreq-events = <&ppmu_leftbus_3>, <&ppmu_rightbus_3>; + vdd-supply = <&buck3_reg>; + status = "okay"; +}; + +&bus_rightbus { + devfreq = <&bus_leftbus>; + status = "okay"; +}; + +&bus_fsys { + devfreq = <&bus_leftbus>; + status = "okay"; +}; + +&bus_peri { + devfreq = <&bus_leftbus>; + status = "okay"; +}; + +&bus_mfc { + devfreq = <&bus_leftbus>; + status = "okay"; +}; + +&cpu0 { + cpu0-supply = <&buck2_reg>; +}; + +&hsotg { + vusb_d-supply = <&ldo15_reg>; + vusb_a-supply = <&ldo12_reg>; +}; + +&i2c_1 { + #address-cells = <1>; + #size-cells = <0>; + samsung,i2c-sda-delay = <100>; + samsung,i2c-max-bus-freq = <400000>; + pinctrl-0 = <&i2c1_bus>; + pinctrl-names = "default"; + status = "okay"; + + s5m8767: s5m8767-pmic@66 { + compatible = "samsung,s5m8767-pmic"; + reg = <0x66>; + + s5m8767,pmic-buck-default-dvs-idx = <3>; + + s5m8767,pmic-buck-dvs-gpios = <&gpb 5 GPIO_ACTIVE_HIGH>, + <&gpb 6 GPIO_ACTIVE_HIGH>, + <&gpb 7 GPIO_ACTIVE_HIGH>; + + s5m8767,pmic-buck-ds-gpios = <&gpm3 5 GPIO_ACTIVE_HIGH>, + <&gpm3 6 GPIO_ACTIVE_HIGH>, + <&gpm3 7 GPIO_ACTIVE_HIGH>; + + /* VDD_ARM */ + s5m8767,pmic-buck2-dvs-voltage = <1356250>, <1300000>, + <1243750>, <1118750>, + <1068750>, <1012500>, + <956250>, <900000>; + /* VDD_INT */ + s5m8767,pmic-buck3-dvs-voltage = <1000000>, <1000000>, + <925000>, <925000>, + <887500>, <887500>, + <850000>, <850000>; + /* VDD_G3D */ + s5m8767,pmic-buck4-dvs-voltage = <1081250>, <1081250>, + <1025000>, <950000>, + <918750>, <900000>, + <875000>, <831250>; + + regulators { + ldo1_reg: LDO1 { + regulator-name = "VDD_ALIVE"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + regulator-boot-on; + op_mode = <1>; /* Normal Mode */ + }; + + /* SCP uses 1.5v, POP uses 1.2v */ + ldo2_reg: LDO2 { + regulator-name = "VDDQ_M12"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-boot-on; + op_mode = <1>; /* Normal Mode */ + }; + + ldo3_reg: LDO3 { + regulator-name = "VDDIOAP_18"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + op_mode = <1>; /* Normal Mode */ + }; + + ldo4_reg: LDO4 { + regulator-name = "VDDQ_PRE"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + op_mode = <1>; /* Normal Mode */ + }; + + ldo5_reg: LDO5 { + regulator-name = "VDD_LDO5"; + op_mode = <0>; /* Always off Mode */ + }; + + ldo6_reg: LDO6 { + regulator-name = "VDD10_MPLL"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + op_mode = <1>; /* Normal Mode */ + }; + + ldo7_reg: LDO7 { + regulator-name = "VDD10_XPLL"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + op_mode = <1>; /* Normal Mode */ + }; + + ldo8_reg: LDO8 { + regulator-name = "VDD10_MIPI"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + op_mode = <1>; /* Normal Mode */ + }; + + ldo9_reg: LDO9 { + regulator-name = "VDD33_LCD"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + op_mode = <1>; /* Normal Mode */ + }; + + ldo10_reg: LDO10 { + regulator-name = "VDD18_MIPI"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + op_mode = <1>; /* Normal Mode */ + }; + + ldo11_reg: LDO11 { + regulator-name = "VDD18_ABB1"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + op_mode = <1>; /* Normal Mode */ + }; + + ldo12_reg: LDO12 { + regulator-name = "VDD33_UOTG"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + op_mode = <1>; /* Normal Mode */ + }; + + ldo13_reg: LDO13 { + regulator-name = "VDDIOPERI_18"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + op_mode = <1>; /* Normal Mode */ + }; + + ldo14_reg: LDO14 { + regulator-name = "VDD18_ABB02"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + op_mode = <1>; /* Normal Mode */ + }; + + ldo15_reg: LDO15 { + regulator-name = "VDD10_USH"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + op_mode = <1>; /* Normal Mode */ + }; + + ldo16_reg: LDO16 { + regulator-name = "VDD18_HSIC"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + op_mode = <1>; /* Normal Mode */ + }; + + ldo17_reg: LDO17 { + regulator-name = "VDDIOAP_MMC012_28"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + op_mode = <1>; /* Normal Mode */ + }; + + /* Used by HSIC */ + ldo18_reg: LDO18 { + regulator-name = "VDDIOPERI_28"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + op_mode = <1>; /* Normal Mode */ + }; + + ldo19_reg: LDO19 { + regulator-name = "VDD_LDO19"; + op_mode = <0>; /* Always off Mode */ + }; + + ldo20_reg: LDO20 { + regulator-name = "VDD28_CAM"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2800000>; + op_mode = <1>; /* Normal Mode */ + }; + + ldo21_reg: LDO21 { + regulator-name = "VDD28_AF"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2800000>; + op_mode = <1>; /* Normal Mode */ + }; + + ldo22_reg: LDO22 { + regulator-name = "VDDA28_2M"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + op_mode = <1>; /* Normal Mode */ + }; + + ldo23_reg: LDO23 { + regulator-name = "VDD28_TF"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + op_mode = <1>; /* Normal Mode */ + }; + + ldo24_reg: LDO24 { + regulator-name = "VDD33_A31"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + op_mode = <1>; /* Normal Mode */ + }; + + ldo25_reg: LDO25 { + regulator-name = "VDD18_CAM"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + op_mode = <1>; /* Normal Mode */ + }; + + ldo26_reg: LDO26 { + regulator-name = "VDD18_A31"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + op_mode = <1>; /* Normal Mode */ + }; + + ldo27_reg: LDO27 { + regulator-name = "GPS_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + op_mode = <1>; /* Normal Mode */ + }; + + ldo28_reg: LDO28 { + regulator-name = "DVDD12"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + op_mode = <1>; /* Normal Mode */ + }; + + buck1_reg: BUCK1 { + regulator-name = "vdd_mif"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + regulator-boot-on; + op_mode = <1>; /* Normal Mode */ + }; + + buck2_reg: BUCK2 { + regulator-name = "vdd_arm"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1456250>; + regulator-always-on; + regulator-boot-on; + op_mode = <1>; /* Normal Mode */ + }; + + buck3_reg: BUCK3 { + regulator-name = "vdd_int"; + regulator-min-microvolt = <875000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-boot-on; + op_mode = <1>; /* Normal Mode */ + }; + + buck4_reg: BUCK4 { + regulator-name = "vdd_g3d"; + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-boot-on; + op_mode = <1>; /* Normal Mode */ + }; + + buck5_reg: BUCK5 { + regulator-name = "vdd_m12"; + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-boot-on; + op_mode = <1>; /* Normal Mode */ + }; + + buck6_reg: BUCK6 { + regulator-name = "vdd12_5m"; + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-boot-on; + op_mode = <1>; /* Normal Mode */ + }; + + buck7_reg: BUCK7 { + regulator-name = "pvdd_buck7"; + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <2000000>; + regulator-boot-on; + regulator-always-on; + op_mode = <1>; /* Normal Mode */ + }; + + buck8_reg: BUCK8 { + regulator-name = "pvdd_buck8"; + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <1500000>; + regulator-boot-on; + regulator-always-on; + op_mode = <1>; /* Normal Mode */ + }; + + buck9_reg: BUCK9 { + regulator-name = "vddf28_emmc"; + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <3000000>; + op_mode = <1>; /* Normal Mode */ + }; + }; + + s5m8767_osc: clocks { + #clock-cells = <1>; + clock-output-names = "s5m8767_ap", + "s5m8767_cp", "s5m8767_bt"; + }; + + }; +}; + +&mfc { + status = "okay"; +}; + +&mshc_0 { + pinctrl-0 = <&sd4_clk &sd4_cmd &sd4_bus4 &sd4_bus8>; + pinctrl-names = "default"; + status = "okay"; + vmmc-supply = <&buck9_reg>; + num-slots = <1>; + broken-cd; + card-detect-delay = <200>; + samsung,dw-mshc-ciu-div = <3>; + samsung,dw-mshc-sdr-timing = <2 3>; + samsung,dw-mshc-ddr-timing = <1 2>; + bus-width = <8>; + cap-mmc-highspeed; +}; + +&pinctrl_1 { + hsic_reset: hsic-reset { + samsung,pins = "gpm2-4"; + samsung,pin-function = <EXYNOS_PIN_PDN_OUT1>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>; + }; +}; + +&rtc { + status = "okay"; + clocks = <&clock CLK_RTC>, <&s5m8767_osc S2MPS11_CLK_AP>; + clock-names = "rtc", "rtc_src"; +}; + +&tmu { + vtmu-supply = <&ldo16_reg>; + status = "okay"; +}; + +&watchdog { + status = "okay"; +}; -- 2.7.4 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply related [flat|nested] 23+ messages in thread
* [PATCH v9 1/2] ARM: dts: Add TOPEET itop core board SCP package version @ 2016-10-18 17:18 ` Randy Li 0 siblings, 0 replies; 23+ messages in thread From: Randy Li @ 2016-10-18 17:18 UTC (permalink / raw) To: devicetree Cc: mark.rutland, linux, kgene, krzk, linux-arm-kernel, linux-samsung-soc, linux-kernel, robh, Randy Li The TOPEET itop is a samsung exnynos 4412 core board, which have two package versions. This patch add the support for SCP version. Currently supported are USB3503A HSIC, USB OTG, eMMC, rtc and PMIC. The future features are in the based board. Also MFC and watchdog have been enabled. Signed-off-by: Randy Li <ayaka@soulik.info> --- arch/arm/boot/dts/exynos4412-itop-scp-core.dtsi | 501 ++++++++++++++++++++++++ 1 file changed, 501 insertions(+) create mode 100644 arch/arm/boot/dts/exynos4412-itop-scp-core.dtsi diff --git a/arch/arm/boot/dts/exynos4412-itop-scp-core.dtsi b/arch/arm/boot/dts/exynos4412-itop-scp-core.dtsi new file mode 100644 index 0000000..881dc76 --- /dev/null +++ b/arch/arm/boot/dts/exynos4412-itop-scp-core.dtsi @@ -0,0 +1,501 @@ +/* + * TOPEET's Exynos4412 based itop board device tree source + * + * Copyright (c) 2016 SUMOMO Computer Association + * https://www.sumomo.mobi + * Randy Li <ayaka@soulik.info> + * + * Device tree source file for TOPEET iTop Exynos 4412 SCP package core + * board which is based on Samsung's Exynos4412 SoC. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <dt-bindings/clock/samsung,s2mps11.h> +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include "exynos4412.dtsi" +#include "exynos4412-ppmu-common.dtsi" +#include "exynos-mfc-reserved-memory.dtsi" + +/ { + memory@40000000 { + device_type = "memory"; + reg = <0x40000000 0x40000000>; + }; + + firmware@0203F000 { + compatible = "samsung,secure-firmware"; + reg = <0x0203F000 0x1000>; + }; + + fixed-rate-clocks { + xxti { + compatible = "samsung,clock-xxti"; + clock-frequency = <0>; + }; + + xusbxti { + compatible = "samsung,clock-xusbxti"; + clock-frequency = <24000000>; + }; + }; + + thermal-zones { + cpu_thermal: cpu-thermal { + cooling-maps { + map0 { + /* Corresponds to 800MHz at freq_table */ + cooling-device = <&cpu0 7 7>; + }; + map1 { + /* Corresponds to 200MHz at freq_table */ + cooling-device = <&cpu0 13 13>; + }; + }; + }; + }; + + usb-hub { + compatible = "smsc,usb3503a"; + reset-gpios = <&gpm2 4 GPIO_ACTIVE_LOW>; + connect-gpios = <&gpm3 3 GPIO_ACTIVE_HIGH>; + intn-gpios = <&gpx2 3 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&hsic_reset>; + }; +}; + +&bus_dmc { + devfreq-events = <&ppmu_dmc0_3>, <&ppmu_dmc1_3>; + vdd-supply = <&buck1_reg>; + status = "okay"; +}; + +&bus_acp { + devfreq = <&bus_dmc>; + status = "okay"; +}; + +&bus_c2c { + devfreq = <&bus_dmc>; + status = "okay"; +}; + +&bus_leftbus { + devfreq-events = <&ppmu_leftbus_3>, <&ppmu_rightbus_3>; + vdd-supply = <&buck3_reg>; + status = "okay"; +}; + +&bus_rightbus { + devfreq = <&bus_leftbus>; + status = "okay"; +}; + +&bus_fsys { + devfreq = <&bus_leftbus>; + status = "okay"; +}; + +&bus_peri { + devfreq = <&bus_leftbus>; + status = "okay"; +}; + +&bus_mfc { + devfreq = <&bus_leftbus>; + status = "okay"; +}; + +&cpu0 { + cpu0-supply = <&buck2_reg>; +}; + +&hsotg { + vusb_d-supply = <&ldo15_reg>; + vusb_a-supply = <&ldo12_reg>; +}; + +&i2c_1 { + #address-cells = <1>; + #size-cells = <0>; + samsung,i2c-sda-delay = <100>; + samsung,i2c-max-bus-freq = <400000>; + pinctrl-0 = <&i2c1_bus>; + pinctrl-names = "default"; + status = "okay"; + + s5m8767: s5m8767-pmic@66 { + compatible = "samsung,s5m8767-pmic"; + reg = <0x66>; + + s5m8767,pmic-buck-default-dvs-idx = <3>; + + s5m8767,pmic-buck-dvs-gpios = <&gpb 5 GPIO_ACTIVE_HIGH>, + <&gpb 6 GPIO_ACTIVE_HIGH>, + <&gpb 7 GPIO_ACTIVE_HIGH>; + + s5m8767,pmic-buck-ds-gpios = <&gpm3 5 GPIO_ACTIVE_HIGH>, + <&gpm3 6 GPIO_ACTIVE_HIGH>, + <&gpm3 7 GPIO_ACTIVE_HIGH>; + + /* VDD_ARM */ + s5m8767,pmic-buck2-dvs-voltage = <1356250>, <1300000>, + <1243750>, <1118750>, + <1068750>, <1012500>, + <956250>, <900000>; + /* VDD_INT */ + s5m8767,pmic-buck3-dvs-voltage = <1000000>, <1000000>, + <925000>, <925000>, + <887500>, <887500>, + <850000>, <850000>; + /* VDD_G3D */ + s5m8767,pmic-buck4-dvs-voltage = <1081250>, <1081250>, + <1025000>, <950000>, + <918750>, <900000>, + <875000>, <831250>; + + regulators { + ldo1_reg: LDO1 { + regulator-name = "VDD_ALIVE"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + regulator-boot-on; + op_mode = <1>; /* Normal Mode */ + }; + + /* SCP uses 1.5v, POP uses 1.2v */ + ldo2_reg: LDO2 { + regulator-name = "VDDQ_M12"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-boot-on; + op_mode = <1>; /* Normal Mode */ + }; + + ldo3_reg: LDO3 { + regulator-name = "VDDIOAP_18"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + op_mode = <1>; /* Normal Mode */ + }; + + ldo4_reg: LDO4 { + regulator-name = "VDDQ_PRE"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + op_mode = <1>; /* Normal Mode */ + }; + + ldo5_reg: LDO5 { + regulator-name = "VDD_LDO5"; + op_mode = <0>; /* Always off Mode */ + }; + + ldo6_reg: LDO6 { + regulator-name = "VDD10_MPLL"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + op_mode = <1>; /* Normal Mode */ + }; + + ldo7_reg: LDO7 { + regulator-name = "VDD10_XPLL"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + op_mode = <1>; /* Normal Mode */ + }; + + ldo8_reg: LDO8 { + regulator-name = "VDD10_MIPI"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + op_mode = <1>; /* Normal Mode */ + }; + + ldo9_reg: LDO9 { + regulator-name = "VDD33_LCD"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + op_mode = <1>; /* Normal Mode */ + }; + + ldo10_reg: LDO10 { + regulator-name = "VDD18_MIPI"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + op_mode = <1>; /* Normal Mode */ + }; + + ldo11_reg: LDO11 { + regulator-name = "VDD18_ABB1"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + op_mode = <1>; /* Normal Mode */ + }; + + ldo12_reg: LDO12 { + regulator-name = "VDD33_UOTG"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + op_mode = <1>; /* Normal Mode */ + }; + + ldo13_reg: LDO13 { + regulator-name = "VDDIOPERI_18"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + op_mode = <1>; /* Normal Mode */ + }; + + ldo14_reg: LDO14 { + regulator-name = "VDD18_ABB02"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + op_mode = <1>; /* Normal Mode */ + }; + + ldo15_reg: LDO15 { + regulator-name = "VDD10_USH"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + op_mode = <1>; /* Normal Mode */ + }; + + ldo16_reg: LDO16 { + regulator-name = "VDD18_HSIC"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + op_mode = <1>; /* Normal Mode */ + }; + + ldo17_reg: LDO17 { + regulator-name = "VDDIOAP_MMC012_28"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + op_mode = <1>; /* Normal Mode */ + }; + + /* Used by HSIC */ + ldo18_reg: LDO18 { + regulator-name = "VDDIOPERI_28"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + op_mode = <1>; /* Normal Mode */ + }; + + ldo19_reg: LDO19 { + regulator-name = "VDD_LDO19"; + op_mode = <0>; /* Always off Mode */ + }; + + ldo20_reg: LDO20 { + regulator-name = "VDD28_CAM"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2800000>; + op_mode = <1>; /* Normal Mode */ + }; + + ldo21_reg: LDO21 { + regulator-name = "VDD28_AF"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2800000>; + op_mode = <1>; /* Normal Mode */ + }; + + ldo22_reg: LDO22 { + regulator-name = "VDDA28_2M"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + op_mode = <1>; /* Normal Mode */ + }; + + ldo23_reg: LDO23 { + regulator-name = "VDD28_TF"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + op_mode = <1>; /* Normal Mode */ + }; + + ldo24_reg: LDO24 { + regulator-name = "VDD33_A31"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + op_mode = <1>; /* Normal Mode */ + }; + + ldo25_reg: LDO25 { + regulator-name = "VDD18_CAM"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + op_mode = <1>; /* Normal Mode */ + }; + + ldo26_reg: LDO26 { + regulator-name = "VDD18_A31"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + op_mode = <1>; /* Normal Mode */ + }; + + ldo27_reg: LDO27 { + regulator-name = "GPS_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + op_mode = <1>; /* Normal Mode */ + }; + + ldo28_reg: LDO28 { + regulator-name = "DVDD12"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + op_mode = <1>; /* Normal Mode */ + }; + + buck1_reg: BUCK1 { + regulator-name = "vdd_mif"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + regulator-boot-on; + op_mode = <1>; /* Normal Mode */ + }; + + buck2_reg: BUCK2 { + regulator-name = "vdd_arm"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1456250>; + regulator-always-on; + regulator-boot-on; + op_mode = <1>; /* Normal Mode */ + }; + + buck3_reg: BUCK3 { + regulator-name = "vdd_int"; + regulator-min-microvolt = <875000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-boot-on; + op_mode = <1>; /* Normal Mode */ + }; + + buck4_reg: BUCK4 { + regulator-name = "vdd_g3d"; + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-boot-on; + op_mode = <1>; /* Normal Mode */ + }; + + buck5_reg: BUCK5 { + regulator-name = "vdd_m12"; + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-boot-on; + op_mode = <1>; /* Normal Mode */ + }; + + buck6_reg: BUCK6 { + regulator-name = "vdd12_5m"; + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-boot-on; + op_mode = <1>; /* Normal Mode */ + }; + + buck7_reg: BUCK7 { + regulator-name = "pvdd_buck7"; + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <2000000>; + regulator-boot-on; + regulator-always-on; + op_mode = <1>; /* Normal Mode */ + }; + + buck8_reg: BUCK8 { + regulator-name = "pvdd_buck8"; + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <1500000>; + regulator-boot-on; + regulator-always-on; + op_mode = <1>; /* Normal Mode */ + }; + + buck9_reg: BUCK9 { + regulator-name = "vddf28_emmc"; + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <3000000>; + op_mode = <1>; /* Normal Mode */ + }; + }; + + s5m8767_osc: clocks { + #clock-cells = <1>; + clock-output-names = "s5m8767_ap", + "s5m8767_cp", "s5m8767_bt"; + }; + + }; +}; + +&mfc { + status = "okay"; +}; + +&mshc_0 { + pinctrl-0 = <&sd4_clk &sd4_cmd &sd4_bus4 &sd4_bus8>; + pinctrl-names = "default"; + status = "okay"; + vmmc-supply = <&buck9_reg>; + num-slots = <1>; + broken-cd; + card-detect-delay = <200>; + samsung,dw-mshc-ciu-div = <3>; + samsung,dw-mshc-sdr-timing = <2 3>; + samsung,dw-mshc-ddr-timing = <1 2>; + bus-width = <8>; + cap-mmc-highspeed; +}; + +&pinctrl_1 { + hsic_reset: hsic-reset { + samsung,pins = "gpm2-4"; + samsung,pin-function = <EXYNOS_PIN_PDN_OUT1>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>; + }; +}; + +&rtc { + status = "okay"; + clocks = <&clock CLK_RTC>, <&s5m8767_osc S2MPS11_CLK_AP>; + clock-names = "rtc", "rtc_src"; +}; + +&tmu { + vtmu-supply = <&ldo16_reg>; + status = "okay"; +}; + +&watchdog { + status = "okay"; +}; -- 2.7.4 ^ permalink raw reply related [flat|nested] 23+ messages in thread
* [PATCH v9 1/2] ARM: dts: Add TOPEET itop core board SCP package version @ 2016-10-18 17:18 ` Randy Li 0 siblings, 0 replies; 23+ messages in thread From: Randy Li @ 2016-10-18 17:18 UTC (permalink / raw) To: linux-arm-kernel The TOPEET itop is a samsung exnynos 4412 core board, which have two package versions. This patch add the support for SCP version. Currently supported are USB3503A HSIC, USB OTG, eMMC, rtc and PMIC. The future features are in the based board. Also MFC and watchdog have been enabled. Signed-off-by: Randy Li <ayaka@soulik.info> --- arch/arm/boot/dts/exynos4412-itop-scp-core.dtsi | 501 ++++++++++++++++++++++++ 1 file changed, 501 insertions(+) create mode 100644 arch/arm/boot/dts/exynos4412-itop-scp-core.dtsi diff --git a/arch/arm/boot/dts/exynos4412-itop-scp-core.dtsi b/arch/arm/boot/dts/exynos4412-itop-scp-core.dtsi new file mode 100644 index 0000000..881dc76 --- /dev/null +++ b/arch/arm/boot/dts/exynos4412-itop-scp-core.dtsi @@ -0,0 +1,501 @@ +/* + * TOPEET's Exynos4412 based itop board device tree source + * + * Copyright (c) 2016 SUMOMO Computer Association + * https://www.sumomo.mobi + * Randy Li <ayaka@soulik.info> + * + * Device tree source file for TOPEET iTop Exynos 4412 SCP package core + * board which is based on Samsung's Exynos4412 SoC. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <dt-bindings/clock/samsung,s2mps11.h> +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include "exynos4412.dtsi" +#include "exynos4412-ppmu-common.dtsi" +#include "exynos-mfc-reserved-memory.dtsi" + +/ { + memory at 40000000 { + device_type = "memory"; + reg = <0x40000000 0x40000000>; + }; + + firmware at 0203F000 { + compatible = "samsung,secure-firmware"; + reg = <0x0203F000 0x1000>; + }; + + fixed-rate-clocks { + xxti { + compatible = "samsung,clock-xxti"; + clock-frequency = <0>; + }; + + xusbxti { + compatible = "samsung,clock-xusbxti"; + clock-frequency = <24000000>; + }; + }; + + thermal-zones { + cpu_thermal: cpu-thermal { + cooling-maps { + map0 { + /* Corresponds to 800MHz at freq_table */ + cooling-device = <&cpu0 7 7>; + }; + map1 { + /* Corresponds to 200MHz at freq_table */ + cooling-device = <&cpu0 13 13>; + }; + }; + }; + }; + + usb-hub { + compatible = "smsc,usb3503a"; + reset-gpios = <&gpm2 4 GPIO_ACTIVE_LOW>; + connect-gpios = <&gpm3 3 GPIO_ACTIVE_HIGH>; + intn-gpios = <&gpx2 3 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&hsic_reset>; + }; +}; + +&bus_dmc { + devfreq-events = <&ppmu_dmc0_3>, <&ppmu_dmc1_3>; + vdd-supply = <&buck1_reg>; + status = "okay"; +}; + +&bus_acp { + devfreq = <&bus_dmc>; + status = "okay"; +}; + +&bus_c2c { + devfreq = <&bus_dmc>; + status = "okay"; +}; + +&bus_leftbus { + devfreq-events = <&ppmu_leftbus_3>, <&ppmu_rightbus_3>; + vdd-supply = <&buck3_reg>; + status = "okay"; +}; + +&bus_rightbus { + devfreq = <&bus_leftbus>; + status = "okay"; +}; + +&bus_fsys { + devfreq = <&bus_leftbus>; + status = "okay"; +}; + +&bus_peri { + devfreq = <&bus_leftbus>; + status = "okay"; +}; + +&bus_mfc { + devfreq = <&bus_leftbus>; + status = "okay"; +}; + +&cpu0 { + cpu0-supply = <&buck2_reg>; +}; + +&hsotg { + vusb_d-supply = <&ldo15_reg>; + vusb_a-supply = <&ldo12_reg>; +}; + +&i2c_1 { + #address-cells = <1>; + #size-cells = <0>; + samsung,i2c-sda-delay = <100>; + samsung,i2c-max-bus-freq = <400000>; + pinctrl-0 = <&i2c1_bus>; + pinctrl-names = "default"; + status = "okay"; + + s5m8767: s5m8767-pmic at 66 { + compatible = "samsung,s5m8767-pmic"; + reg = <0x66>; + + s5m8767,pmic-buck-default-dvs-idx = <3>; + + s5m8767,pmic-buck-dvs-gpios = <&gpb 5 GPIO_ACTIVE_HIGH>, + <&gpb 6 GPIO_ACTIVE_HIGH>, + <&gpb 7 GPIO_ACTIVE_HIGH>; + + s5m8767,pmic-buck-ds-gpios = <&gpm3 5 GPIO_ACTIVE_HIGH>, + <&gpm3 6 GPIO_ACTIVE_HIGH>, + <&gpm3 7 GPIO_ACTIVE_HIGH>; + + /* VDD_ARM */ + s5m8767,pmic-buck2-dvs-voltage = <1356250>, <1300000>, + <1243750>, <1118750>, + <1068750>, <1012500>, + <956250>, <900000>; + /* VDD_INT */ + s5m8767,pmic-buck3-dvs-voltage = <1000000>, <1000000>, + <925000>, <925000>, + <887500>, <887500>, + <850000>, <850000>; + /* VDD_G3D */ + s5m8767,pmic-buck4-dvs-voltage = <1081250>, <1081250>, + <1025000>, <950000>, + <918750>, <900000>, + <875000>, <831250>; + + regulators { + ldo1_reg: LDO1 { + regulator-name = "VDD_ALIVE"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + regulator-boot-on; + op_mode = <1>; /* Normal Mode */ + }; + + /* SCP uses 1.5v, POP uses 1.2v */ + ldo2_reg: LDO2 { + regulator-name = "VDDQ_M12"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-boot-on; + op_mode = <1>; /* Normal Mode */ + }; + + ldo3_reg: LDO3 { + regulator-name = "VDDIOAP_18"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + op_mode = <1>; /* Normal Mode */ + }; + + ldo4_reg: LDO4 { + regulator-name = "VDDQ_PRE"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + op_mode = <1>; /* Normal Mode */ + }; + + ldo5_reg: LDO5 { + regulator-name = "VDD_LDO5"; + op_mode = <0>; /* Always off Mode */ + }; + + ldo6_reg: LDO6 { + regulator-name = "VDD10_MPLL"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + op_mode = <1>; /* Normal Mode */ + }; + + ldo7_reg: LDO7 { + regulator-name = "VDD10_XPLL"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + op_mode = <1>; /* Normal Mode */ + }; + + ldo8_reg: LDO8 { + regulator-name = "VDD10_MIPI"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + op_mode = <1>; /* Normal Mode */ + }; + + ldo9_reg: LDO9 { + regulator-name = "VDD33_LCD"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + op_mode = <1>; /* Normal Mode */ + }; + + ldo10_reg: LDO10 { + regulator-name = "VDD18_MIPI"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + op_mode = <1>; /* Normal Mode */ + }; + + ldo11_reg: LDO11 { + regulator-name = "VDD18_ABB1"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + op_mode = <1>; /* Normal Mode */ + }; + + ldo12_reg: LDO12 { + regulator-name = "VDD33_UOTG"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + op_mode = <1>; /* Normal Mode */ + }; + + ldo13_reg: LDO13 { + regulator-name = "VDDIOPERI_18"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + op_mode = <1>; /* Normal Mode */ + }; + + ldo14_reg: LDO14 { + regulator-name = "VDD18_ABB02"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + op_mode = <1>; /* Normal Mode */ + }; + + ldo15_reg: LDO15 { + regulator-name = "VDD10_USH"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + op_mode = <1>; /* Normal Mode */ + }; + + ldo16_reg: LDO16 { + regulator-name = "VDD18_HSIC"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + op_mode = <1>; /* Normal Mode */ + }; + + ldo17_reg: LDO17 { + regulator-name = "VDDIOAP_MMC012_28"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + op_mode = <1>; /* Normal Mode */ + }; + + /* Used by HSIC */ + ldo18_reg: LDO18 { + regulator-name = "VDDIOPERI_28"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + op_mode = <1>; /* Normal Mode */ + }; + + ldo19_reg: LDO19 { + regulator-name = "VDD_LDO19"; + op_mode = <0>; /* Always off Mode */ + }; + + ldo20_reg: LDO20 { + regulator-name = "VDD28_CAM"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2800000>; + op_mode = <1>; /* Normal Mode */ + }; + + ldo21_reg: LDO21 { + regulator-name = "VDD28_AF"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2800000>; + op_mode = <1>; /* Normal Mode */ + }; + + ldo22_reg: LDO22 { + regulator-name = "VDDA28_2M"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + op_mode = <1>; /* Normal Mode */ + }; + + ldo23_reg: LDO23 { + regulator-name = "VDD28_TF"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + op_mode = <1>; /* Normal Mode */ + }; + + ldo24_reg: LDO24 { + regulator-name = "VDD33_A31"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + op_mode = <1>; /* Normal Mode */ + }; + + ldo25_reg: LDO25 { + regulator-name = "VDD18_CAM"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + op_mode = <1>; /* Normal Mode */ + }; + + ldo26_reg: LDO26 { + regulator-name = "VDD18_A31"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + op_mode = <1>; /* Normal Mode */ + }; + + ldo27_reg: LDO27 { + regulator-name = "GPS_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + op_mode = <1>; /* Normal Mode */ + }; + + ldo28_reg: LDO28 { + regulator-name = "DVDD12"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + op_mode = <1>; /* Normal Mode */ + }; + + buck1_reg: BUCK1 { + regulator-name = "vdd_mif"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + regulator-boot-on; + op_mode = <1>; /* Normal Mode */ + }; + + buck2_reg: BUCK2 { + regulator-name = "vdd_arm"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1456250>; + regulator-always-on; + regulator-boot-on; + op_mode = <1>; /* Normal Mode */ + }; + + buck3_reg: BUCK3 { + regulator-name = "vdd_int"; + regulator-min-microvolt = <875000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-boot-on; + op_mode = <1>; /* Normal Mode */ + }; + + buck4_reg: BUCK4 { + regulator-name = "vdd_g3d"; + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-boot-on; + op_mode = <1>; /* Normal Mode */ + }; + + buck5_reg: BUCK5 { + regulator-name = "vdd_m12"; + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-boot-on; + op_mode = <1>; /* Normal Mode */ + }; + + buck6_reg: BUCK6 { + regulator-name = "vdd12_5m"; + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-boot-on; + op_mode = <1>; /* Normal Mode */ + }; + + buck7_reg: BUCK7 { + regulator-name = "pvdd_buck7"; + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <2000000>; + regulator-boot-on; + regulator-always-on; + op_mode = <1>; /* Normal Mode */ + }; + + buck8_reg: BUCK8 { + regulator-name = "pvdd_buck8"; + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <1500000>; + regulator-boot-on; + regulator-always-on; + op_mode = <1>; /* Normal Mode */ + }; + + buck9_reg: BUCK9 { + regulator-name = "vddf28_emmc"; + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <3000000>; + op_mode = <1>; /* Normal Mode */ + }; + }; + + s5m8767_osc: clocks { + #clock-cells = <1>; + clock-output-names = "s5m8767_ap", + "s5m8767_cp", "s5m8767_bt"; + }; + + }; +}; + +&mfc { + status = "okay"; +}; + +&mshc_0 { + pinctrl-0 = <&sd4_clk &sd4_cmd &sd4_bus4 &sd4_bus8>; + pinctrl-names = "default"; + status = "okay"; + vmmc-supply = <&buck9_reg>; + num-slots = <1>; + broken-cd; + card-detect-delay = <200>; + samsung,dw-mshc-ciu-div = <3>; + samsung,dw-mshc-sdr-timing = <2 3>; + samsung,dw-mshc-ddr-timing = <1 2>; + bus-width = <8>; + cap-mmc-highspeed; +}; + +&pinctrl_1 { + hsic_reset: hsic-reset { + samsung,pins = "gpm2-4"; + samsung,pin-function = <EXYNOS_PIN_PDN_OUT1>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>; + }; +}; + +&rtc { + status = "okay"; + clocks = <&clock CLK_RTC>, <&s5m8767_osc S2MPS11_CLK_AP>; + clock-names = "rtc", "rtc_src"; +}; + +&tmu { + vtmu-supply = <&ldo16_reg>; + status = "okay"; +}; + +&watchdog { + status = "okay"; +}; -- 2.7.4 ^ permalink raw reply related [flat|nested] 23+ messages in thread
[parent not found: <1476811129-4450-2-git-send-email-ayaka-xPW3/0Ywev/iB9QmIjCX8w@public.gmane.org>]
* Re: [PATCH v9 1/2] ARM: dts: Add TOPEET itop core board SCP package version 2016-10-18 17:18 ` Randy Li (?) @ 2016-10-18 17:34 ` Krzysztof Kozlowski -1 siblings, 0 replies; 23+ messages in thread From: Krzysztof Kozlowski @ 2016-10-18 17:34 UTC (permalink / raw) To: Randy Li Cc: devicetree-u79uwXL29TY76Z2rM5mHXA, mark.rutland-5wv7dgnIgG8, linux-I+IVW8TIWO2tmTQ+vhA3Yw, kgene-DgEjT+Ai2ygdnm+yROfE0A, krzk-DgEjT+Ai2ygdnm+yROfE0A, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, linux-samsung-soc-u79uwXL29TY76Z2rM5mHXA, linux-kernel-u79uwXL29TY76Z2rM5mHXA, robh-DgEjT+Ai2ygdnm+yROfE0A On Wed, Oct 19, 2016 at 01:18:48AM +0800, Randy Li wrote: > The TOPEET itop is a samsung exnynos 4412 core board, which have > two package versions. This patch add the support for SCP version. > > Currently supported are USB3503A HSIC, USB OTG, eMMC, rtc and > PMIC. The future features are in the based board. Also MFC and > watchdog have been enabled. > > Signed-off-by: Randy Li <ayaka-xPW3/0Ywev/iB9QmIjCX8w@public.gmane.org> > --- > arch/arm/boot/dts/exynos4412-itop-scp-core.dtsi | 501 ++++++++++++++++++++++++ > 1 file changed, 501 insertions(+) > create mode 100644 arch/arm/boot/dts/exynos4412-itop-scp-core.dtsi Thanks, applied, with minor changes in commit msg and fix in pin function (you used macro for pull up/down instead of function). Best regards, Krzysztof -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 23+ messages in thread
* Re: [PATCH v9 1/2] ARM: dts: Add TOPEET itop core board SCP package version @ 2016-10-18 17:34 ` Krzysztof Kozlowski 0 siblings, 0 replies; 23+ messages in thread From: Krzysztof Kozlowski @ 2016-10-18 17:34 UTC (permalink / raw) To: Randy Li Cc: devicetree, mark.rutland, linux, kgene, krzk, linux-arm-kernel, linux-samsung-soc, linux-kernel, robh On Wed, Oct 19, 2016 at 01:18:48AM +0800, Randy Li wrote: > The TOPEET itop is a samsung exnynos 4412 core board, which have > two package versions. This patch add the support for SCP version. > > Currently supported are USB3503A HSIC, USB OTG, eMMC, rtc and > PMIC. The future features are in the based board. Also MFC and > watchdog have been enabled. > > Signed-off-by: Randy Li <ayaka@soulik.info> > --- > arch/arm/boot/dts/exynos4412-itop-scp-core.dtsi | 501 ++++++++++++++++++++++++ > 1 file changed, 501 insertions(+) > create mode 100644 arch/arm/boot/dts/exynos4412-itop-scp-core.dtsi Thanks, applied, with minor changes in commit msg and fix in pin function (you used macro for pull up/down instead of function). Best regards, Krzysztof ^ permalink raw reply [flat|nested] 23+ messages in thread
* [PATCH v9 1/2] ARM: dts: Add TOPEET itop core board SCP package version @ 2016-10-18 17:34 ` Krzysztof Kozlowski 0 siblings, 0 replies; 23+ messages in thread From: Krzysztof Kozlowski @ 2016-10-18 17:34 UTC (permalink / raw) To: linux-arm-kernel On Wed, Oct 19, 2016 at 01:18:48AM +0800, Randy Li wrote: > The TOPEET itop is a samsung exnynos 4412 core board, which have > two package versions. This patch add the support for SCP version. > > Currently supported are USB3503A HSIC, USB OTG, eMMC, rtc and > PMIC. The future features are in the based board. Also MFC and > watchdog have been enabled. > > Signed-off-by: Randy Li <ayaka@soulik.info> > --- > arch/arm/boot/dts/exynos4412-itop-scp-core.dtsi | 501 ++++++++++++++++++++++++ > 1 file changed, 501 insertions(+) > create mode 100644 arch/arm/boot/dts/exynos4412-itop-scp-core.dtsi Thanks, applied, with minor changes in commit msg and fix in pin function (you used macro for pull up/down instead of function). Best regards, Krzysztof ^ permalink raw reply [flat|nested] 23+ messages in thread
* [PATCH v9 2/2] ARM: dts: add TOPEET itop elite based board 2016-10-18 17:18 ` Randy Li (?) @ 2016-10-18 17:18 ` Randy Li -1 siblings, 0 replies; 23+ messages in thread From: Randy Li @ 2016-10-18 17:18 UTC (permalink / raw) To: devicetree-u79uwXL29TY76Z2rM5mHXA Cc: mark.rutland-5wv7dgnIgG8, linux-I+IVW8TIWO2tmTQ+vhA3Yw, kgene-DgEjT+Ai2ygdnm+yROfE0A, krzk-DgEjT+Ai2ygdnm+yROfE0A, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, linux-samsung-soc-u79uwXL29TY76Z2rM5mHXA, linux-kernel-u79uwXL29TY76Z2rM5mHXA, robh-DgEjT+Ai2ygdnm+yROfE0A, Randy Li The TOPEET itop exynos 4412 have three versions base board. The Elite version is the cheap one without too much peripheral devices on it. Currently supported are serial console, wired networking(USB), USB OTG in peripheral mode, USB host, SD storage, GPIO buttons, PWM beeper, ADC and LEDs. The WM8960 analog audio codec is also enabled. The FIMC is not used for camera currently, I enabled it just for a colorspace converter. Signed-off-by: Randy Li <ayaka-xPW3/0Ywev/iB9QmIjCX8w@public.gmane.org> Reviewed-by: Krzysztof Kozlowski <krzk-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org> --- .../bindings/arm/samsung/samsung-boards.txt | 3 + arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/exynos4412-itop-elite.dts | 240 +++++++++++++++++++++ 3 files changed, 244 insertions(+) create mode 100644 arch/arm/boot/dts/exynos4412-itop-elite.dts diff --git a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt index 0ea7f14..5160fa5 100644 --- a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt +++ b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt @@ -22,6 +22,9 @@ Required root node properties: * FriendlyARM - "friendlyarm,tiny4412" - for Exynos4412-based FriendlyARM TINY4412 board. + * TOPEET + - "topeet,itop4412-elite" - for Exynos4412-based TOPEET + Elite base board. * Google - "google,pi" - for Exynos5800-based Google Peach Pi diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index befcd26..d709f74 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -136,6 +136,7 @@ dtb-$(CONFIG_ARCH_EXYNOS4) += \ exynos4210-smdkv310.dtb \ exynos4210-trats.dtb \ exynos4210-universal_c210.dtb \ + exynos4412-itop-elite.dtb \ exynos4412-odroidu3.dtb \ exynos4412-odroidx.dtb \ exynos4412-odroidx2.dtb \ diff --git a/arch/arm/boot/dts/exynos4412-itop-elite.dts b/arch/arm/boot/dts/exynos4412-itop-elite.dts new file mode 100644 index 0000000..7440e54 --- /dev/null +++ b/arch/arm/boot/dts/exynos4412-itop-elite.dts @@ -0,0 +1,240 @@ +/* + * TOPEET's Exynos4412 based itop board device tree source + * + * Copyright (c) 2016 SUMOMO Computer Association + * https://www.sumomo.mobi + * Randy Li <ayaka-xPW3/0Ywev/iB9QmIjCX8w@public.gmane.org> + * + * Device tree source file for TOPEET iTop Exynos 4412 core board + * which is based on Samsung's Exynos4412 SoC. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/dts-v1/; +#include <dt-bindings/pwm/pwm.h> +#include <dt-bindings/sound/samsung-i2s.h> +#include "exynos4412-itop-scp-core.dtsi" + +/ { + model = "TOPEET iTop 4412 Elite board based on Exynos4412"; + compatible = "topeet,itop4412-elite", "samsung,exynos4412", "samsung,exynos4"; + + chosen { + bootargs = "root=/dev/mmcblk0p2 rw rootfstype=ext4 rootdelay=1 rootwait"; + stdout-path = "serial2:115200n8"; + }; + + leds { + compatible = "gpio-leds"; + + led2 { + label = "red:system"; + gpios = <&gpx1 0 GPIO_ACTIVE_HIGH>; + default-state = "off"; + linux,default-trigger = "heartbeat"; + }; + + led3 { + label = "red:user"; + gpios = <&gpk1 1 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + + home { + label = "GPIO Key Home"; + linux,code = <KEY_HOME>; + gpios = <&gpx1 1 GPIO_ACTIVE_LOW>; + }; + + back { + label = "GPIO Key Back"; + linux,code = <KEY_BACK>; + gpios = <&gpx1 2 GPIO_ACTIVE_LOW>; + }; + + sleep { + label = "GPIO Key Sleep"; + linux,code = <KEY_POWER>; + gpios = <&gpx3 3 GPIO_ACTIVE_LOW>; + }; + + vol-up { + label = "GPIO Key Vol+"; + linux,code = <KEY_UP>; + gpios = <&gpx2 1 GPIO_ACTIVE_LOW>; + }; + + vol-down { + label = "GPIO Key Vol-"; + linux,code = <KEY_DOWN>; + gpios = <&gpx2 0 GPIO_ACTIVE_LOW>; + }; + }; + + sound { + compatible = "simple-audio-card"; + simple-audio-card,name = "wm-sound"; + + assigned-clocks = <&clock_audss EXYNOS_MOUT_AUDSS>, + <&clock_audss EXYNOS_MOUT_I2S>, + <&clock_audss EXYNOS_DOUT_SRP>, + <&clock_audss EXYNOS_DOUT_AUD_BUS>; + assigned-clock-parents = <&clock CLK_FOUT_EPLL>, + <&clock_audss EXYNOS_MOUT_AUDSS>; + assigned-clock-rates = <0>, + <0>, + <112896000>, + <11289600>; + + simple-audio-card,format = "i2s"; + simple-audio-card,bitclock-master = <&link0_codec>; + simple-audio-card,frame-master = <&link0_codec>; + + simple-audio-card,widgets = + "Microphone", "Mic Jack", + "Line", "Line In", + "Line", "Line Out", + "Speaker", "Speaker", + "Headphone", "Headphone Jack"; + simple-audio-card,routing = + "Headphone Jack", "HP_L", + "Headphone Jack", "HP_R", + "Speaker", "SPK_LP", + "Speaker", "SPK_LN", + "Speaker", "SPK_RP", + "Speaker", "SPK_RN", + "LINPUT1", "Mic Jack", + "LINPUT3", "Mic Jack", + "RINPUT1", "Mic Jack", + "RINPUT2", "Mic Jack"; + + simple-audio-card,cpu { + sound-dai = <&i2s0 0>; + }; + + link0_codec: simple-audio-card,codec { + sound-dai = <&codec>; + clocks = <&i2s0 CLK_I2S_CDCLK>; + system-clock-frequency = <11289600>; + }; + }; + + beep { + compatible = "pwm-beeper"; + pwms = <&pwm 0 4000000 PWM_POLARITY_INVERTED>; + }; + + camera: camera { + pinctrl-0 = <&cam_port_a_clk_active>; + pinctrl-names = "default"; + status = "okay"; + assigned-clocks = <&clock CLK_MOUT_CAM0>; + assigned-clock-parents = <&clock CLK_XUSBXTI>; + }; +}; + +&adc { + vdd-supply = <&ldo3_reg>; + status = "okay"; +}; + +&ehci { + status = "okay"; + /* In order to reset USB ethernet */ + samsung,vbus-gpio = <&gpc0 1 GPIO_ACTIVE_HIGH>; + + port@0 { + status = "okay"; + }; + + port@2 { + status = "okay"; + }; +}; + +&exynos_usbphy { + status = "okay"; +}; + +&fimc_0 { + status = "okay"; + assigned-clocks = <&clock CLK_MOUT_FIMC0>, + <&clock CLK_SCLK_FIMC0>; + assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>; + assigned-clock-rates = <0>, <176000000>; +}; + +&hsotg { + dr_mode = "peripheral"; + status = "okay"; +}; + +&i2c_4 { + samsung,i2c-sda-delay = <100>; + samsung,i2c-slave-addr = <0x10>; + samsung,i2c-max-bus-freq = <100000>; + pinctrl-0 = <&i2c4_bus>; + pinctrl-names = "default"; + status = "okay"; + + codec: wm8960@1a { + compatible = "wlf,wm8960"; + reg = <0x1a>; + clocks = <&pmu_system_controller 0>; + clock-names = "MCLK1"; + wlf,shared-lrclk; + #sound-dai-cells = <0>; + }; +}; + +&i2s0 { + pinctrl-0 = <&i2s0_bus>; + pinctrl-names = "default"; + status = "okay"; + clocks = <&clock_audss EXYNOS_I2S_BUS>, + <&clock_audss EXYNOS_DOUT_AUD_BUS>, + <&clock_audss EXYNOS_SCLK_I2S>; + clock-names = "iis", "i2s_opclk0", "i2s_opclk1"; +}; + +&pinctrl_1 { + ether-reset { + samsung,pins = "gpc0-1"; + samsung,pin-function = <EXYNOS_PIN_PDN_OUT1>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; + }; +}; + +&pwm { + status = "okay"; + pinctrl-0 = <&pwm0_out>; + pinctrl-names = "default"; + samsung,pwm-outputs = <0>; +}; + +&sdhci_2 { + bus-width = <4>; + pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4>; + pinctrl-names = "default"; + cd-gpio = <&gpx0 7 GPIO_ACTIVE_LOW>; + cap-sd-highspeed; + vmmc-supply = <&ldo23_reg>; + vqmmc-supply = <&ldo17_reg>; + status = "okay"; +}; + +&serial_1 { + status = "okay"; +}; + +&serial_2 { + status = "okay"; +}; -- 2.7.4 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply related [flat|nested] 23+ messages in thread
* [PATCH v9 2/2] ARM: dts: add TOPEET itop elite based board @ 2016-10-18 17:18 ` Randy Li 0 siblings, 0 replies; 23+ messages in thread From: Randy Li @ 2016-10-18 17:18 UTC (permalink / raw) To: devicetree Cc: mark.rutland, linux, kgene, krzk, linux-arm-kernel, linux-samsung-soc, linux-kernel, robh, Randy Li The TOPEET itop exynos 4412 have three versions base board. The Elite version is the cheap one without too much peripheral devices on it. Currently supported are serial console, wired networking(USB), USB OTG in peripheral mode, USB host, SD storage, GPIO buttons, PWM beeper, ADC and LEDs. The WM8960 analog audio codec is also enabled. The FIMC is not used for camera currently, I enabled it just for a colorspace converter. Signed-off-by: Randy Li <ayaka@soulik.info> Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org> --- .../bindings/arm/samsung/samsung-boards.txt | 3 + arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/exynos4412-itop-elite.dts | 240 +++++++++++++++++++++ 3 files changed, 244 insertions(+) create mode 100644 arch/arm/boot/dts/exynos4412-itop-elite.dts diff --git a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt index 0ea7f14..5160fa5 100644 --- a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt +++ b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt @@ -22,6 +22,9 @@ Required root node properties: * FriendlyARM - "friendlyarm,tiny4412" - for Exynos4412-based FriendlyARM TINY4412 board. + * TOPEET + - "topeet,itop4412-elite" - for Exynos4412-based TOPEET + Elite base board. * Google - "google,pi" - for Exynos5800-based Google Peach Pi diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index befcd26..d709f74 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -136,6 +136,7 @@ dtb-$(CONFIG_ARCH_EXYNOS4) += \ exynos4210-smdkv310.dtb \ exynos4210-trats.dtb \ exynos4210-universal_c210.dtb \ + exynos4412-itop-elite.dtb \ exynos4412-odroidu3.dtb \ exynos4412-odroidx.dtb \ exynos4412-odroidx2.dtb \ diff --git a/arch/arm/boot/dts/exynos4412-itop-elite.dts b/arch/arm/boot/dts/exynos4412-itop-elite.dts new file mode 100644 index 0000000..7440e54 --- /dev/null +++ b/arch/arm/boot/dts/exynos4412-itop-elite.dts @@ -0,0 +1,240 @@ +/* + * TOPEET's Exynos4412 based itop board device tree source + * + * Copyright (c) 2016 SUMOMO Computer Association + * https://www.sumomo.mobi + * Randy Li <ayaka@soulik.info> + * + * Device tree source file for TOPEET iTop Exynos 4412 core board + * which is based on Samsung's Exynos4412 SoC. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/dts-v1/; +#include <dt-bindings/pwm/pwm.h> +#include <dt-bindings/sound/samsung-i2s.h> +#include "exynos4412-itop-scp-core.dtsi" + +/ { + model = "TOPEET iTop 4412 Elite board based on Exynos4412"; + compatible = "topeet,itop4412-elite", "samsung,exynos4412", "samsung,exynos4"; + + chosen { + bootargs = "root=/dev/mmcblk0p2 rw rootfstype=ext4 rootdelay=1 rootwait"; + stdout-path = "serial2:115200n8"; + }; + + leds { + compatible = "gpio-leds"; + + led2 { + label = "red:system"; + gpios = <&gpx1 0 GPIO_ACTIVE_HIGH>; + default-state = "off"; + linux,default-trigger = "heartbeat"; + }; + + led3 { + label = "red:user"; + gpios = <&gpk1 1 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + + home { + label = "GPIO Key Home"; + linux,code = <KEY_HOME>; + gpios = <&gpx1 1 GPIO_ACTIVE_LOW>; + }; + + back { + label = "GPIO Key Back"; + linux,code = <KEY_BACK>; + gpios = <&gpx1 2 GPIO_ACTIVE_LOW>; + }; + + sleep { + label = "GPIO Key Sleep"; + linux,code = <KEY_POWER>; + gpios = <&gpx3 3 GPIO_ACTIVE_LOW>; + }; + + vol-up { + label = "GPIO Key Vol+"; + linux,code = <KEY_UP>; + gpios = <&gpx2 1 GPIO_ACTIVE_LOW>; + }; + + vol-down { + label = "GPIO Key Vol-"; + linux,code = <KEY_DOWN>; + gpios = <&gpx2 0 GPIO_ACTIVE_LOW>; + }; + }; + + sound { + compatible = "simple-audio-card"; + simple-audio-card,name = "wm-sound"; + + assigned-clocks = <&clock_audss EXYNOS_MOUT_AUDSS>, + <&clock_audss EXYNOS_MOUT_I2S>, + <&clock_audss EXYNOS_DOUT_SRP>, + <&clock_audss EXYNOS_DOUT_AUD_BUS>; + assigned-clock-parents = <&clock CLK_FOUT_EPLL>, + <&clock_audss EXYNOS_MOUT_AUDSS>; + assigned-clock-rates = <0>, + <0>, + <112896000>, + <11289600>; + + simple-audio-card,format = "i2s"; + simple-audio-card,bitclock-master = <&link0_codec>; + simple-audio-card,frame-master = <&link0_codec>; + + simple-audio-card,widgets = + "Microphone", "Mic Jack", + "Line", "Line In", + "Line", "Line Out", + "Speaker", "Speaker", + "Headphone", "Headphone Jack"; + simple-audio-card,routing = + "Headphone Jack", "HP_L", + "Headphone Jack", "HP_R", + "Speaker", "SPK_LP", + "Speaker", "SPK_LN", + "Speaker", "SPK_RP", + "Speaker", "SPK_RN", + "LINPUT1", "Mic Jack", + "LINPUT3", "Mic Jack", + "RINPUT1", "Mic Jack", + "RINPUT2", "Mic Jack"; + + simple-audio-card,cpu { + sound-dai = <&i2s0 0>; + }; + + link0_codec: simple-audio-card,codec { + sound-dai = <&codec>; + clocks = <&i2s0 CLK_I2S_CDCLK>; + system-clock-frequency = <11289600>; + }; + }; + + beep { + compatible = "pwm-beeper"; + pwms = <&pwm 0 4000000 PWM_POLARITY_INVERTED>; + }; + + camera: camera { + pinctrl-0 = <&cam_port_a_clk_active>; + pinctrl-names = "default"; + status = "okay"; + assigned-clocks = <&clock CLK_MOUT_CAM0>; + assigned-clock-parents = <&clock CLK_XUSBXTI>; + }; +}; + +&adc { + vdd-supply = <&ldo3_reg>; + status = "okay"; +}; + +&ehci { + status = "okay"; + /* In order to reset USB ethernet */ + samsung,vbus-gpio = <&gpc0 1 GPIO_ACTIVE_HIGH>; + + port@0 { + status = "okay"; + }; + + port@2 { + status = "okay"; + }; +}; + +&exynos_usbphy { + status = "okay"; +}; + +&fimc_0 { + status = "okay"; + assigned-clocks = <&clock CLK_MOUT_FIMC0>, + <&clock CLK_SCLK_FIMC0>; + assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>; + assigned-clock-rates = <0>, <176000000>; +}; + +&hsotg { + dr_mode = "peripheral"; + status = "okay"; +}; + +&i2c_4 { + samsung,i2c-sda-delay = <100>; + samsung,i2c-slave-addr = <0x10>; + samsung,i2c-max-bus-freq = <100000>; + pinctrl-0 = <&i2c4_bus>; + pinctrl-names = "default"; + status = "okay"; + + codec: wm8960@1a { + compatible = "wlf,wm8960"; + reg = <0x1a>; + clocks = <&pmu_system_controller 0>; + clock-names = "MCLK1"; + wlf,shared-lrclk; + #sound-dai-cells = <0>; + }; +}; + +&i2s0 { + pinctrl-0 = <&i2s0_bus>; + pinctrl-names = "default"; + status = "okay"; + clocks = <&clock_audss EXYNOS_I2S_BUS>, + <&clock_audss EXYNOS_DOUT_AUD_BUS>, + <&clock_audss EXYNOS_SCLK_I2S>; + clock-names = "iis", "i2s_opclk0", "i2s_opclk1"; +}; + +&pinctrl_1 { + ether-reset { + samsung,pins = "gpc0-1"; + samsung,pin-function = <EXYNOS_PIN_PDN_OUT1>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; + }; +}; + +&pwm { + status = "okay"; + pinctrl-0 = <&pwm0_out>; + pinctrl-names = "default"; + samsung,pwm-outputs = <0>; +}; + +&sdhci_2 { + bus-width = <4>; + pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4>; + pinctrl-names = "default"; + cd-gpio = <&gpx0 7 GPIO_ACTIVE_LOW>; + cap-sd-highspeed; + vmmc-supply = <&ldo23_reg>; + vqmmc-supply = <&ldo17_reg>; + status = "okay"; +}; + +&serial_1 { + status = "okay"; +}; + +&serial_2 { + status = "okay"; +}; -- 2.7.4 ^ permalink raw reply related [flat|nested] 23+ messages in thread
* [PATCH v9 2/2] ARM: dts: add TOPEET itop elite based board @ 2016-10-18 17:18 ` Randy Li 0 siblings, 0 replies; 23+ messages in thread From: Randy Li @ 2016-10-18 17:18 UTC (permalink / raw) To: linux-arm-kernel The TOPEET itop exynos 4412 have three versions base board. The Elite version is the cheap one without too much peripheral devices on it. Currently supported are serial console, wired networking(USB), USB OTG in peripheral mode, USB host, SD storage, GPIO buttons, PWM beeper, ADC and LEDs. The WM8960 analog audio codec is also enabled. The FIMC is not used for camera currently, I enabled it just for a colorspace converter. Signed-off-by: Randy Li <ayaka@soulik.info> Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org> --- .../bindings/arm/samsung/samsung-boards.txt | 3 + arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/exynos4412-itop-elite.dts | 240 +++++++++++++++++++++ 3 files changed, 244 insertions(+) create mode 100644 arch/arm/boot/dts/exynos4412-itop-elite.dts diff --git a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt index 0ea7f14..5160fa5 100644 --- a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt +++ b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt @@ -22,6 +22,9 @@ Required root node properties: * FriendlyARM - "friendlyarm,tiny4412" - for Exynos4412-based FriendlyARM TINY4412 board. + * TOPEET + - "topeet,itop4412-elite" - for Exynos4412-based TOPEET + Elite base board. * Google - "google,pi" - for Exynos5800-based Google Peach Pi diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index befcd26..d709f74 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -136,6 +136,7 @@ dtb-$(CONFIG_ARCH_EXYNOS4) += \ exynos4210-smdkv310.dtb \ exynos4210-trats.dtb \ exynos4210-universal_c210.dtb \ + exynos4412-itop-elite.dtb \ exynos4412-odroidu3.dtb \ exynos4412-odroidx.dtb \ exynos4412-odroidx2.dtb \ diff --git a/arch/arm/boot/dts/exynos4412-itop-elite.dts b/arch/arm/boot/dts/exynos4412-itop-elite.dts new file mode 100644 index 0000000..7440e54 --- /dev/null +++ b/arch/arm/boot/dts/exynos4412-itop-elite.dts @@ -0,0 +1,240 @@ +/* + * TOPEET's Exynos4412 based itop board device tree source + * + * Copyright (c) 2016 SUMOMO Computer Association + * https://www.sumomo.mobi + * Randy Li <ayaka@soulik.info> + * + * Device tree source file for TOPEET iTop Exynos 4412 core board + * which is based on Samsung's Exynos4412 SoC. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/dts-v1/; +#include <dt-bindings/pwm/pwm.h> +#include <dt-bindings/sound/samsung-i2s.h> +#include "exynos4412-itop-scp-core.dtsi" + +/ { + model = "TOPEET iTop 4412 Elite board based on Exynos4412"; + compatible = "topeet,itop4412-elite", "samsung,exynos4412", "samsung,exynos4"; + + chosen { + bootargs = "root=/dev/mmcblk0p2 rw rootfstype=ext4 rootdelay=1 rootwait"; + stdout-path = "serial2:115200n8"; + }; + + leds { + compatible = "gpio-leds"; + + led2 { + label = "red:system"; + gpios = <&gpx1 0 GPIO_ACTIVE_HIGH>; + default-state = "off"; + linux,default-trigger = "heartbeat"; + }; + + led3 { + label = "red:user"; + gpios = <&gpk1 1 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + + home { + label = "GPIO Key Home"; + linux,code = <KEY_HOME>; + gpios = <&gpx1 1 GPIO_ACTIVE_LOW>; + }; + + back { + label = "GPIO Key Back"; + linux,code = <KEY_BACK>; + gpios = <&gpx1 2 GPIO_ACTIVE_LOW>; + }; + + sleep { + label = "GPIO Key Sleep"; + linux,code = <KEY_POWER>; + gpios = <&gpx3 3 GPIO_ACTIVE_LOW>; + }; + + vol-up { + label = "GPIO Key Vol+"; + linux,code = <KEY_UP>; + gpios = <&gpx2 1 GPIO_ACTIVE_LOW>; + }; + + vol-down { + label = "GPIO Key Vol-"; + linux,code = <KEY_DOWN>; + gpios = <&gpx2 0 GPIO_ACTIVE_LOW>; + }; + }; + + sound { + compatible = "simple-audio-card"; + simple-audio-card,name = "wm-sound"; + + assigned-clocks = <&clock_audss EXYNOS_MOUT_AUDSS>, + <&clock_audss EXYNOS_MOUT_I2S>, + <&clock_audss EXYNOS_DOUT_SRP>, + <&clock_audss EXYNOS_DOUT_AUD_BUS>; + assigned-clock-parents = <&clock CLK_FOUT_EPLL>, + <&clock_audss EXYNOS_MOUT_AUDSS>; + assigned-clock-rates = <0>, + <0>, + <112896000>, + <11289600>; + + simple-audio-card,format = "i2s"; + simple-audio-card,bitclock-master = <&link0_codec>; + simple-audio-card,frame-master = <&link0_codec>; + + simple-audio-card,widgets = + "Microphone", "Mic Jack", + "Line", "Line In", + "Line", "Line Out", + "Speaker", "Speaker", + "Headphone", "Headphone Jack"; + simple-audio-card,routing = + "Headphone Jack", "HP_L", + "Headphone Jack", "HP_R", + "Speaker", "SPK_LP", + "Speaker", "SPK_LN", + "Speaker", "SPK_RP", + "Speaker", "SPK_RN", + "LINPUT1", "Mic Jack", + "LINPUT3", "Mic Jack", + "RINPUT1", "Mic Jack", + "RINPUT2", "Mic Jack"; + + simple-audio-card,cpu { + sound-dai = <&i2s0 0>; + }; + + link0_codec: simple-audio-card,codec { + sound-dai = <&codec>; + clocks = <&i2s0 CLK_I2S_CDCLK>; + system-clock-frequency = <11289600>; + }; + }; + + beep { + compatible = "pwm-beeper"; + pwms = <&pwm 0 4000000 PWM_POLARITY_INVERTED>; + }; + + camera: camera { + pinctrl-0 = <&cam_port_a_clk_active>; + pinctrl-names = "default"; + status = "okay"; + assigned-clocks = <&clock CLK_MOUT_CAM0>; + assigned-clock-parents = <&clock CLK_XUSBXTI>; + }; +}; + +&adc { + vdd-supply = <&ldo3_reg>; + status = "okay"; +}; + +&ehci { + status = "okay"; + /* In order to reset USB ethernet */ + samsung,vbus-gpio = <&gpc0 1 GPIO_ACTIVE_HIGH>; + + port at 0 { + status = "okay"; + }; + + port at 2 { + status = "okay"; + }; +}; + +&exynos_usbphy { + status = "okay"; +}; + +&fimc_0 { + status = "okay"; + assigned-clocks = <&clock CLK_MOUT_FIMC0>, + <&clock CLK_SCLK_FIMC0>; + assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>; + assigned-clock-rates = <0>, <176000000>; +}; + +&hsotg { + dr_mode = "peripheral"; + status = "okay"; +}; + +&i2c_4 { + samsung,i2c-sda-delay = <100>; + samsung,i2c-slave-addr = <0x10>; + samsung,i2c-max-bus-freq = <100000>; + pinctrl-0 = <&i2c4_bus>; + pinctrl-names = "default"; + status = "okay"; + + codec: wm8960 at 1a { + compatible = "wlf,wm8960"; + reg = <0x1a>; + clocks = <&pmu_system_controller 0>; + clock-names = "MCLK1"; + wlf,shared-lrclk; + #sound-dai-cells = <0>; + }; +}; + +&i2s0 { + pinctrl-0 = <&i2s0_bus>; + pinctrl-names = "default"; + status = "okay"; + clocks = <&clock_audss EXYNOS_I2S_BUS>, + <&clock_audss EXYNOS_DOUT_AUD_BUS>, + <&clock_audss EXYNOS_SCLK_I2S>; + clock-names = "iis", "i2s_opclk0", "i2s_opclk1"; +}; + +&pinctrl_1 { + ether-reset { + samsung,pins = "gpc0-1"; + samsung,pin-function = <EXYNOS_PIN_PDN_OUT1>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; + }; +}; + +&pwm { + status = "okay"; + pinctrl-0 = <&pwm0_out>; + pinctrl-names = "default"; + samsung,pwm-outputs = <0>; +}; + +&sdhci_2 { + bus-width = <4>; + pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4>; + pinctrl-names = "default"; + cd-gpio = <&gpx0 7 GPIO_ACTIVE_LOW>; + cap-sd-highspeed; + vmmc-supply = <&ldo23_reg>; + vqmmc-supply = <&ldo17_reg>; + status = "okay"; +}; + +&serial_1 { + status = "okay"; +}; + +&serial_2 { + status = "okay"; +}; -- 2.7.4 ^ permalink raw reply related [flat|nested] 23+ messages in thread
* Re: [PATCH v9 2/2] ARM: dts: add TOPEET itop elite based board 2016-10-18 17:18 ` Randy Li @ 2016-10-18 17:37 ` Krzysztof Kozlowski -1 siblings, 0 replies; 23+ messages in thread From: Krzysztof Kozlowski @ 2016-10-18 17:37 UTC (permalink / raw) To: Randy Li Cc: devicetree, mark.rutland, linux, kgene, krzk, linux-arm-kernel, linux-samsung-soc, linux-kernel, robh On Wed, Oct 19, 2016 at 01:18:49AM +0800, Randy Li wrote: > The TOPEET itop exynos 4412 have three versions base board. The > Elite version is the cheap one without too much peripheral devices > on it. > > Currently supported are serial console, wired networking(USB), > USB OTG in peripheral mode, USB host, SD storage, GPIO buttons, > PWM beeper, ADC and LEDs. The WM8960 analog audio codec is also > enabled. > > The FIMC is not used for camera currently, I enabled it just for a > colorspace converter. > > Signed-off-by: Randy Li <ayaka@soulik.info> > Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org> Thanks, applied, with missing Rob's ack, minor changes in commit msg and fix in pin function (you used macro for pull up/down instead of function). Best regards, Krzysztof ^ permalink raw reply [flat|nested] 23+ messages in thread
* [PATCH v9 2/2] ARM: dts: add TOPEET itop elite based board @ 2016-10-18 17:37 ` Krzysztof Kozlowski 0 siblings, 0 replies; 23+ messages in thread From: Krzysztof Kozlowski @ 2016-10-18 17:37 UTC (permalink / raw) To: linux-arm-kernel On Wed, Oct 19, 2016 at 01:18:49AM +0800, Randy Li wrote: > The TOPEET itop exynos 4412 have three versions base board. The > Elite version is the cheap one without too much peripheral devices > on it. > > Currently supported are serial console, wired networking(USB), > USB OTG in peripheral mode, USB host, SD storage, GPIO buttons, > PWM beeper, ADC and LEDs. The WM8960 analog audio codec is also > enabled. > > The FIMC is not used for camera currently, I enabled it just for a > colorspace converter. > > Signed-off-by: Randy Li <ayaka@soulik.info> > Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org> Thanks, applied, with missing Rob's ack, minor changes in commit msg and fix in pin function (you used macro for pull up/down instead of function). Best regards, Krzysztof ^ permalink raw reply [flat|nested] 23+ messages in thread
* Re: [PATCH v9 2/2] ARM: dts: add TOPEET itop elite based board 2016-10-18 17:37 ` Krzysztof Kozlowski @ 2016-10-18 17:47 ` Krzysztof Kozlowski -1 siblings, 0 replies; 23+ messages in thread From: Krzysztof Kozlowski @ 2016-10-18 17:47 UTC (permalink / raw) To: Krzysztof Kozlowski Cc: Randy Li, devicetree, mark.rutland, linux, kgene, linux-arm-kernel, linux-samsung-soc, linux-kernel, robh On Tue, Oct 18, 2016 at 08:37:48PM +0300, Krzysztof Kozlowski wrote: > On Wed, Oct 19, 2016 at 01:18:49AM +0800, Randy Li wrote: > > The TOPEET itop exynos 4412 have three versions base board. The > > Elite version is the cheap one without too much peripheral devices > > on it. > > > > Currently supported are serial console, wired networking(USB), > > USB OTG in peripheral mode, USB host, SD storage, GPIO buttons, > > PWM beeper, ADC and LEDs. The WM8960 analog audio codec is also > > enabled. > > > > The FIMC is not used for camera currently, I enabled it just for a > > colorspace converter. > > > > Signed-off-by: Randy Li <ayaka@soulik.info> > > Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org> > > Thanks, applied, with missing Rob's ack, minor changes in commit msg and > fix in pin function (you used macro for pull up/down instead of > function). I also changed your name in commit message from "ayaka" to "Randy Li". The author of a patch (equal to "From:" in email) should match the Signed-off-by. For the future, please fix your gitconfig and/or mail transfer program. Sample gitconfig regarding this: [user] name = Mr Foo Bar email = foobar@gmail.com [sendemail] smtpencryption = tls smtpserver = smtp.gmail.com smtpuser = foobar@gmail.com smtpserverport = 587 confirm = auto Best regards, Krzysztof ^ permalink raw reply [flat|nested] 23+ messages in thread
* [PATCH v9 2/2] ARM: dts: add TOPEET itop elite based board @ 2016-10-18 17:47 ` Krzysztof Kozlowski 0 siblings, 0 replies; 23+ messages in thread From: Krzysztof Kozlowski @ 2016-10-18 17:47 UTC (permalink / raw) To: linux-arm-kernel On Tue, Oct 18, 2016 at 08:37:48PM +0300, Krzysztof Kozlowski wrote: > On Wed, Oct 19, 2016 at 01:18:49AM +0800, Randy Li wrote: > > The TOPEET itop exynos 4412 have three versions base board. The > > Elite version is the cheap one without too much peripheral devices > > on it. > > > > Currently supported are serial console, wired networking(USB), > > USB OTG in peripheral mode, USB host, SD storage, GPIO buttons, > > PWM beeper, ADC and LEDs. The WM8960 analog audio codec is also > > enabled. > > > > The FIMC is not used for camera currently, I enabled it just for a > > colorspace converter. > > > > Signed-off-by: Randy Li <ayaka@soulik.info> > > Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org> > > Thanks, applied, with missing Rob's ack, minor changes in commit msg and > fix in pin function (you used macro for pull up/down instead of > function). I also changed your name in commit message from "ayaka" to "Randy Li". The author of a patch (equal to "From:" in email) should match the Signed-off-by. For the future, please fix your gitconfig and/or mail transfer program. Sample gitconfig regarding this: [user] name = Mr Foo Bar email = foobar at gmail.com [sendemail] smtpencryption = tls smtpserver = smtp.gmail.com smtpuser = foobar at gmail.com smtpserverport = 587 confirm = auto Best regards, Krzysztof ^ permalink raw reply [flat|nested] 23+ messages in thread
* Re: [PATCH v9 2/2] ARM: dts: add TOPEET itop elite based board 2016-10-18 17:47 ` Krzysztof Kozlowski @ 2016-10-18 17:57 ` Krzysztof Kozlowski -1 siblings, 0 replies; 23+ messages in thread From: Krzysztof Kozlowski @ 2016-10-18 17:57 UTC (permalink / raw) To: Krzysztof Kozlowski Cc: Randy Li, devicetree, mark.rutland, linux, kgene, linux-arm-kernel, linux-samsung-soc, linux-kernel, robh On Tue, Oct 18, 2016 at 8:47 PM, Krzysztof Kozlowski <krzk@kernel.org> wrote: > On Tue, Oct 18, 2016 at 08:37:48PM +0300, Krzysztof Kozlowski wrote: >> On Wed, Oct 19, 2016 at 01:18:49AM +0800, Randy Li wrote: >> > The TOPEET itop exynos 4412 have three versions base board. The >> > Elite version is the cheap one without too much peripheral devices >> > on it. >> > >> > Currently supported are serial console, wired networking(USB), >> > USB OTG in peripheral mode, USB host, SD storage, GPIO buttons, >> > PWM beeper, ADC and LEDs. The WM8960 analog audio codec is also >> > enabled. >> > >> > The FIMC is not used for camera currently, I enabled it just for a >> > colorspace converter. >> > >> > Signed-off-by: Randy Li <ayaka@soulik.info> >> > Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org> >> >> Thanks, applied, with missing Rob's ack, minor changes in commit msg and >> fix in pin function (you used macro for pull up/down instead of >> function). > > I also changed your name in commit message from "ayaka" to "Randy Li". > The author of a patch (equal to "From:" in email) should match the > Signed-off-by. For the future, please fix your gitconfig and/or mail > transfer program. Ahhh, it is not your fault but patchwork's. Damn it. Patchwork stores the first username he encounters and uses it further even if From is different. I will send an email to kernel.org Patchwork admin about this. Best regards, Krzysztof ^ permalink raw reply [flat|nested] 23+ messages in thread
* [PATCH v9 2/2] ARM: dts: add TOPEET itop elite based board @ 2016-10-18 17:57 ` Krzysztof Kozlowski 0 siblings, 0 replies; 23+ messages in thread From: Krzysztof Kozlowski @ 2016-10-18 17:57 UTC (permalink / raw) To: linux-arm-kernel On Tue, Oct 18, 2016 at 8:47 PM, Krzysztof Kozlowski <krzk@kernel.org> wrote: > On Tue, Oct 18, 2016 at 08:37:48PM +0300, Krzysztof Kozlowski wrote: >> On Wed, Oct 19, 2016 at 01:18:49AM +0800, Randy Li wrote: >> > The TOPEET itop exynos 4412 have three versions base board. The >> > Elite version is the cheap one without too much peripheral devices >> > on it. >> > >> > Currently supported are serial console, wired networking(USB), >> > USB OTG in peripheral mode, USB host, SD storage, GPIO buttons, >> > PWM beeper, ADC and LEDs. The WM8960 analog audio codec is also >> > enabled. >> > >> > The FIMC is not used for camera currently, I enabled it just for a >> > colorspace converter. >> > >> > Signed-off-by: Randy Li <ayaka@soulik.info> >> > Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org> >> >> Thanks, applied, with missing Rob's ack, minor changes in commit msg and >> fix in pin function (you used macro for pull up/down instead of >> function). > > I also changed your name in commit message from "ayaka" to "Randy Li". > The author of a patch (equal to "From:" in email) should match the > Signed-off-by. For the future, please fix your gitconfig and/or mail > transfer program. Ahhh, it is not your fault but patchwork's. Damn it. Patchwork stores the first username he encounters and uses it further even if From is different. I will send an email to kernel.org Patchwork admin about this. Best regards, Krzysztof ^ permalink raw reply [flat|nested] 23+ messages in thread
* Re: [PATCH v9 2/2] ARM: dts: add TOPEET itop elite based board 2016-10-18 17:37 ` Krzysztof Kozlowski @ 2016-10-19 1:15 ` Ayaka -1 siblings, 0 replies; 23+ messages in thread From: Ayaka @ 2016-10-19 1:15 UTC (permalink / raw) To: Krzysztof Kozlowski Cc: devicetree, mark.rutland, linux, kgene, linux-arm-kernel, linux-samsung-soc, linux-kernel, robh 從我的 iPad 傳送 > Krzysztof Kozlowski <krzk@kernel.org> 於 2016年10月19日 上午1:37 寫道： > >> On Wed, Oct 19, 2016 at 01:18:49AM +0800, Randy Li wrote: >> The TOPEET itop exynos 4412 have three versions base board. The >> Elite version is the cheap one without too much peripheral devices >> on it. >> >> Currently supported are serial console, wired networking(USB), >> USB OTG in peripheral mode, USB host, SD storage, GPIO buttons, >> PWM beeper, ADC and LEDs. The WM8960 analog audio codec is also >> enabled. >> >> The FIMC is not used for camera currently, I enabled it just for a >> colorspace converter. >> >> Signed-off-by: Randy Li <ayaka@soulik.info> >> Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org> > > Thanks, applied, with missing Rob's ack, minor changes in commit msg and > fix in pin function (you used macro for pull up/down instead of > function). The last time I saw the other dts have applied that, but they are not now. A header file is also missed reported by kbuild, but I didn't meet that. > > Best regards, > Krzysztof ^ permalink raw reply [flat|nested] 23+ messages in thread
* [PATCH v9 2/2] ARM: dts: add TOPEET itop elite based board @ 2016-10-19 1:15 ` Ayaka 0 siblings, 0 replies; 23+ messages in thread From: Ayaka @ 2016-10-19 1:15 UTC (permalink / raw) To: linux-arm-kernel ??? iPad ?? > Krzysztof Kozlowski <krzk@kernel.org> ? 2016?10?19? ??1:37 ??? > >> On Wed, Oct 19, 2016 at 01:18:49AM +0800, Randy Li wrote: >> The TOPEET itop exynos 4412 have three versions base board. The >> Elite version is the cheap one without too much peripheral devices >> on it. >> >> Currently supported are serial console, wired networking(USB), >> USB OTG in peripheral mode, USB host, SD storage, GPIO buttons, >> PWM beeper, ADC and LEDs. The WM8960 analog audio codec is also >> enabled. >> >> The FIMC is not used for camera currently, I enabled it just for a >> colorspace converter. >> >> Signed-off-by: Randy Li <ayaka@soulik.info> >> Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org> > > Thanks, applied, with missing Rob's ack, minor changes in commit msg and > fix in pin function (you used macro for pull up/down instead of > function). The last time I saw the other dts have applied that, but they are not now. A header file is also missed reported by kbuild, but I didn't meet that. > > Best regards, > Krzysztof ^ permalink raw reply [flat|nested] 23+ messages in thread
[parent not found: <58DB0A67-6C74-409B-80B2-9F02492D3A55-xPW3/0Ywev/iB9QmIjCX8w@public.gmane.org>]
* Re: [PATCH v9 2/2] ARM: dts: add TOPEET itop elite based board 2016-10-19 1:15 ` Ayaka (?) @ 2016-10-19 5:51 ` Krzysztof Kozlowski -1 siblings, 0 replies; 23+ messages in thread From: Krzysztof Kozlowski @ 2016-10-19 5:51 UTC (permalink / raw) To: Ayaka Cc: devicetree-u79uwXL29TY76Z2rM5mHXA, mark.rutland-5wv7dgnIgG8, linux-I+IVW8TIWO2tmTQ+vhA3Yw, kgene-DgEjT+Ai2ygdnm+yROfE0A, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, linux-samsung-soc-u79uwXL29TY76Z2rM5mHXA, linux-kernel-u79uwXL29TY76Z2rM5mHXA, robh-DgEjT+Ai2ygdnm+yROfE0A On Wed, Oct 19, 2016 at 4:15 AM, Ayaka <ayaka-xPW3/0Ywev/iB9QmIjCX8w@public.gmane.org> wrote: > > > 從我的 iPad 傳送 > >> Krzysztof Kozlowski <krzk-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org> 於 2016年10月19日 上午1:37 寫道： >> >>> On Wed, Oct 19, 2016 at 01:18:49AM +0800, Randy Li wrote: >>> The TOPEET itop exynos 4412 have three versions base board. The >>> Elite version is the cheap one without too much peripheral devices >>> on it. >>> >>> Currently supported are serial console, wired networking(USB), >>> USB OTG in peripheral mode, USB host, SD storage, GPIO buttons, >>> PWM beeper, ADC and LEDs. The WM8960 analog audio codec is also >>> enabled. >>> >>> The FIMC is not used for camera currently, I enabled it just for a >>> colorspace converter. >>> >>> Signed-off-by: Randy Li <ayaka-xPW3/0Ywev/iB9QmIjCX8w@public.gmane.org> >>> Reviewed-by: Krzysztof Kozlowski <krzk-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org> >> >> Thanks, applied, with missing Rob's ack, minor changes in commit msg and >> fix in pin function (you used macro for pull up/down instead of >> function). > The last time I saw the other dts have applied that, but they are not now. A header file is also missed reported by kbuild, but I didn't meet that. I wonder why I didn't encounter the build error on my machine... This needs a follow up fix. Best regards, Krzysztof -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 23+ messages in thread
* Re: [PATCH v9 2/2] ARM: dts: add TOPEET itop elite based board @ 2016-10-19 5:51 ` Krzysztof Kozlowski 0 siblings, 0 replies; 23+ messages in thread From: Krzysztof Kozlowski @ 2016-10-19 5:51 UTC (permalink / raw) To: Ayaka Cc: devicetree, mark.rutland, linux, kgene, linux-arm-kernel, linux-samsung-soc, linux-kernel, robh On Wed, Oct 19, 2016 at 4:15 AM, Ayaka <ayaka@soulik.info> wrote: > > > 從我的 iPad 傳送 > >> Krzysztof Kozlowski <krzk@kernel.org> 於 2016年10月19日 上午1:37 寫道： >> >>> On Wed, Oct 19, 2016 at 01:18:49AM +0800, Randy Li wrote: >>> The TOPEET itop exynos 4412 have three versions base board. The >>> Elite version is the cheap one without too much peripheral devices >>> on it. >>> >>> Currently supported are serial console, wired networking(USB), >>> USB OTG in peripheral mode, USB host, SD storage, GPIO buttons, >>> PWM beeper, ADC and LEDs. The WM8960 analog audio codec is also >>> enabled. >>> >>> The FIMC is not used for camera currently, I enabled it just for a >>> colorspace converter. >>> >>> Signed-off-by: Randy Li <ayaka@soulik.info> >>> Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org> >> >> Thanks, applied, with missing Rob's ack, minor changes in commit msg and >> fix in pin function (you used macro for pull up/down instead of >> function). > The last time I saw the other dts have applied that, but they are not now. A header file is also missed reported by kbuild, but I didn't meet that. I wonder why I didn't encounter the build error on my machine... This needs a follow up fix. Best regards, Krzysztof ^ permalink raw reply [flat|nested] 23+ messages in thread
* [PATCH v9 2/2] ARM: dts: add TOPEET itop elite based board @ 2016-10-19 5:51 ` Krzysztof Kozlowski 0 siblings, 0 replies; 23+ messages in thread From: Krzysztof Kozlowski @ 2016-10-19 5:51 UTC (permalink / raw) To: linux-arm-kernel On Wed, Oct 19, 2016 at 4:15 AM, Ayaka <ayaka@soulik.info> wrote: > > > ??? iPad ?? > >> Krzysztof Kozlowski <krzk@kernel.org> ? 2016?10?19? ??1:37 ??? >> >>> On Wed, Oct 19, 2016 at 01:18:49AM +0800, Randy Li wrote: >>> The TOPEET itop exynos 4412 have three versions base board. The >>> Elite version is the cheap one without too much peripheral devices >>> on it. >>> >>> Currently supported are serial console, wired networking(USB), >>> USB OTG in peripheral mode, USB host, SD storage, GPIO buttons, >>> PWM beeper, ADC and LEDs. The WM8960 analog audio codec is also >>> enabled. >>> >>> The FIMC is not used for camera currently, I enabled it just for a >>> colorspace converter. >>> >>> Signed-off-by: Randy Li <ayaka@soulik.info> >>> Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org> >> >> Thanks, applied, with missing Rob's ack, minor changes in commit msg and >> fix in pin function (you used macro for pull up/down instead of >> function). > The last time I saw the other dts have applied that, but they are not now. A header file is also missed reported by kbuild, but I didn't meet that. I wonder why I didn't encounter the build error on my machine... This needs a follow up fix. Best regards, Krzysztof ^ permalink raw reply [flat|nested] 23+ messages in thread
end of thread, other threads:[~2016-10-19 5:51 UTC | newest]
Thread overview: 23+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <devicetree@vger.kernel.org>
2016-10-18 17:18 ` [PATCH v9 0/2] Add a new board TOPEET iTOP for Exynos 4412 Randy Li
2016-10-18 17:18 ` Randy Li
2016-10-18 17:18 ` Randy Li
[not found] ` <1476811129-4450-1-git-send-email-ayaka-xPW3/0Ywev/iB9QmIjCX8w@public.gmane.org>
2016-10-18 17:18 ` [PATCH v9 1/2] ARM: dts: Add TOPEET itop core board SCP package version Randy Li
2016-10-18 17:18 ` Randy Li
2016-10-18 17:18 ` Randy Li
[not found] ` <1476811129-4450-2-git-send-email-ayaka-xPW3/0Ywev/iB9QmIjCX8w@public.gmane.org>
2016-10-18 17:34 ` Krzysztof Kozlowski
2016-10-18 17:34 ` Krzysztof Kozlowski
2016-10-18 17:34 ` Krzysztof Kozlowski
2016-10-18 17:18 ` [PATCH v9 2/2] ARM: dts: add TOPEET itop elite based board Randy Li
2016-10-18 17:18 ` Randy Li
2016-10-18 17:18 ` Randy Li
2016-10-18 17:37 ` Krzysztof Kozlowski
2016-10-18 17:37 ` Krzysztof Kozlowski
2016-10-18 17:47 ` Krzysztof Kozlowski
2016-10-18 17:47 ` Krzysztof Kozlowski
2016-10-18 17:57 ` Krzysztof Kozlowski
2016-10-18 17:57 ` Krzysztof Kozlowski
2016-10-19 1:15 ` Ayaka
2016-10-19 1:15 ` Ayaka
[not found] ` <58DB0A67-6C74-409B-80B2-9F02492D3A55-xPW3/0Ywev/iB9QmIjCX8w@public.gmane.org>
2016-10-19 5:51 ` Krzysztof Kozlowski
2016-10-19 5:51 ` Krzysztof Kozlowski
2016-10-19 5:51 ` Krzysztof Kozlowski
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.