All of lore.kernel.org
 help / color / mirror / Atom feed
From: moritz.fischer@ettus.com (Moritz Fischer)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v2 5/5] fpga manager: cyclone-ps-spi: make delay variable
Date: Fri, 28 Oct 2016 10:41:42 -0700	[thread overview]
Message-ID: <20161028174142.GA18325@live.com> (raw)
In-Reply-To: <2239ffc8aba7d053825d2bea122a3c16cdd9f6e1.1477669745.git.stillcompiling@gmail.com>

Hi Joshua,

looks good to me; however, I think since you're adding initial support,
I'd squash this together with [3/5].

On Fri, Oct 28, 2016 at 09:56:42AM -0700, Joshua Clayton wrote:
> The status pin may not show ready in the time described in the
> Altetera manual. check the value several times before giving up

s/Altetera/Altera
> For the hardware I am working on, the status pin takes 250 us,
> 5 times as long as described by Altera.
> 
> Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
> ---
>  drivers/fpga/cyclone-ps-spi.c | 13 ++++++++-----
>  1 file changed, 8 insertions(+), 5 deletions(-)
> 
> diff --git a/drivers/fpga/cyclone-ps-spi.c b/drivers/fpga/cyclone-ps-spi.c
> index 4b70d5c..c368223 100644
> --- a/drivers/fpga/cyclone-ps-spi.c
> +++ b/drivers/fpga/cyclone-ps-spi.c
> @@ -20,6 +20,7 @@
>  
>  #define FPGA_RESET_TIME		50   /* time in usecs to trigger FPGA config */
> -#define FPGA_MIN_DELAY		250  /* min usecs to wait for config status */
> +#define FPGA_MIN_DELAY		50   /* min usecs to wait for config status */
> +#define FPGA_MAX_DELAY		1000 /* max usecs to wait for config status */
>  
>  struct cyclonespi_conf {
>  	struct gpio_desc *config;
> @@ -42,6 +43,7 @@ static int cyclonespi_write_init(struct fpga_manager *mgr, u32 flags,
>  				 const char *buf, size_t count)
>  {
>  	struct cyclonespi_conf *conf = (struct cyclonespi_conf *)mgr->priv;
> +	int i;
>  
>  	if (flags & FPGA_MGR_PARTIAL_RECONFIG) {
>  		dev_err(&mgr->dev, "Partial reconfiguration not supported.\n");
> @@ -56,13 +58,14 @@ static int cyclonespi_write_init(struct fpga_manager *mgr, u32 flags,
>  	}
>  
>  	gpiod_set_value(conf->config, 1);
> -	usleep_range(FPGA_MIN_DELAY, FPGA_MIN_DELAY + 20);
> -	if (gpiod_get_value(conf->status) == 0) {
> -		dev_err(&mgr->dev, "Status pin not ready.\n");
> -		return -EIO;
> +	for (i = 0; i < (FPGA_MAX_DELAY / FPGA_MIN_DELAY); i++) {
> +		usleep_range(FPGA_MIN_DELAY, FPGA_MIN_DELAY + 20);
> +		if (gpiod_get_value(conf->status))
> +			return 0;
>  	}
>  
> -	return 0;
> +	dev_err(&mgr->dev, "Status pin not ready.\n");
> +	return -EIO;
>  }
>  
>  static void rev_buf(void *buf, size_t len)
> -- 
> 2.7.4
> 

Cheers,

Moritz

WARNING: multiple messages have this Message-ID (diff)
From: Moritz Fischer <moritz.fischer@ettus.com>
To: Joshua Clayton <stillcompiling@gmail.com>
Cc: Alan Tull <atull@opensource.altera.com>,
	Rob Herring <robh+dt@kernel.org>,
	Mark Rutland <mark.rutland@arm.com>,
	Shawn Guo <shawnguo@kernel.org>,
	Sascha Hauer <kernel@pengutronix.de>,
	Fabio Estevam <fabio.estevam@nxp.com>,
	Russell King <linux@armlinux.org.uk>,
	devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
	linux-arm-kernel@lists.infradead.org
Subject: Re: [PATCH v2 5/5] fpga manager: cyclone-ps-spi: make delay variable
Date: Fri, 28 Oct 2016 10:41:42 -0700	[thread overview]
Message-ID: <20161028174142.GA18325@live.com> (raw)
In-Reply-To: <2239ffc8aba7d053825d2bea122a3c16cdd9f6e1.1477669745.git.stillcompiling@gmail.com>

Hi Joshua,

looks good to me; however, I think since you're adding initial support,
I'd squash this together with [3/5].

On Fri, Oct 28, 2016 at 09:56:42AM -0700, Joshua Clayton wrote:
> The status pin may not show ready in the time described in the
> Altetera manual. check the value several times before giving up

s/Altetera/Altera
> For the hardware I am working on, the status pin takes 250 us,
> 5 times as long as described by Altera.
> 
> Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
> ---
>  drivers/fpga/cyclone-ps-spi.c | 13 ++++++++-----
>  1 file changed, 8 insertions(+), 5 deletions(-)
> 
> diff --git a/drivers/fpga/cyclone-ps-spi.c b/drivers/fpga/cyclone-ps-spi.c
> index 4b70d5c..c368223 100644
> --- a/drivers/fpga/cyclone-ps-spi.c
> +++ b/drivers/fpga/cyclone-ps-spi.c
> @@ -20,6 +20,7 @@
>  
>  #define FPGA_RESET_TIME		50   /* time in usecs to trigger FPGA config */
> -#define FPGA_MIN_DELAY		250  /* min usecs to wait for config status */
> +#define FPGA_MIN_DELAY		50   /* min usecs to wait for config status */
> +#define FPGA_MAX_DELAY		1000 /* max usecs to wait for config status */
>  
>  struct cyclonespi_conf {
>  	struct gpio_desc *config;
> @@ -42,6 +43,7 @@ static int cyclonespi_write_init(struct fpga_manager *mgr, u32 flags,
>  				 const char *buf, size_t count)
>  {
>  	struct cyclonespi_conf *conf = (struct cyclonespi_conf *)mgr->priv;
> +	int i;
>  
>  	if (flags & FPGA_MGR_PARTIAL_RECONFIG) {
>  		dev_err(&mgr->dev, "Partial reconfiguration not supported.\n");
> @@ -56,13 +58,14 @@ static int cyclonespi_write_init(struct fpga_manager *mgr, u32 flags,
>  	}
>  
>  	gpiod_set_value(conf->config, 1);
> -	usleep_range(FPGA_MIN_DELAY, FPGA_MIN_DELAY + 20);
> -	if (gpiod_get_value(conf->status) == 0) {
> -		dev_err(&mgr->dev, "Status pin not ready.\n");
> -		return -EIO;
> +	for (i = 0; i < (FPGA_MAX_DELAY / FPGA_MIN_DELAY); i++) {
> +		usleep_range(FPGA_MIN_DELAY, FPGA_MIN_DELAY + 20);
> +		if (gpiod_get_value(conf->status))
> +			return 0;
>  	}
>  
> -	return 0;
> +	dev_err(&mgr->dev, "Status pin not ready.\n");
> +	return -EIO;
>  }
>  
>  static void rev_buf(void *buf, size_t len)
> -- 
> 2.7.4
> 

Cheers,

Moritz

  reply	other threads:[~2016-10-28 17:41 UTC|newest]

Thread overview: 36+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2016-10-28 16:56 [PATCH v2 0/4] Altera Cyclone Passive Serial SPI FPGA Manager Joshua Clayton
2016-10-28 16:56 ` Joshua Clayton
2016-10-28 16:56 ` Joshua Clayton
2016-10-28 16:56 ` [PATCH v2 1/5] lib: add bitrev8x4() Joshua Clayton
2016-10-28 16:56   ` Joshua Clayton
2016-10-28 18:50   ` kbuild test robot
2016-10-28 18:50     ` kbuild test robot
2016-10-28 18:50     ` kbuild test robot
2016-10-28 16:56 ` [PATCH v2 2/5] doc: dt: add cyclone-spi binding document Joshua Clayton
2016-10-28 16:56   ` Joshua Clayton
2016-10-28 16:56   ` Joshua Clayton
2016-10-31  6:16   ` Rob Herring
2016-10-31  6:16     ` Rob Herring
2016-10-31  6:16     ` Rob Herring
2016-10-28 16:56 ` [PATCH v2 3/5] fpga manager: Add cyclone-ps-spi driver for Altera FPGAs Joshua Clayton
2016-10-28 16:56   ` Joshua Clayton
2016-10-28 18:55   ` kbuild test robot
2016-10-28 18:55     ` kbuild test robot
2016-10-28 18:55     ` kbuild test robot
2016-10-28 19:26   ` kbuild test robot
2016-10-28 19:26     ` kbuild test robot
2016-10-28 19:26     ` kbuild test robot
2016-10-28 20:41   ` kbuild test robot
2016-10-28 20:41     ` kbuild test robot
2016-10-28 20:41     ` kbuild test robot
2016-10-28 21:05     ` Joshua Clayton
2016-10-28 21:05       ` Joshua Clayton
2016-10-28 21:05       ` Joshua Clayton
2016-10-28 16:56 ` [PATCH v2 4/5] ARM: dts: imx6q-evi: support cyclonespi Joshua Clayton
2016-10-28 16:56   ` Joshua Clayton
2016-10-28 16:56 ` [PATCH v2 5/5] fpga manager: cyclone-ps-spi: make delay variable Joshua Clayton
2016-10-28 16:56   ` Joshua Clayton
2016-10-28 17:41   ` Moritz Fischer [this message]
2016-10-28 17:41     ` Moritz Fischer
2016-10-28 19:49     ` Joshua Clayton
2016-10-28 19:49       ` Joshua Clayton

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20161028174142.GA18325@live.com \
    --to=moritz.fischer@ettus.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.