[U-Boot] [PATCH v2 2/4] davinci: omapl138_lcdk: configure ddr2

[Tom Rini <trini@konsulko.com>]

On Mon, Nov 28, 2016 at 02:38:34PM +0100, Fabien Parent wrote:
> On Tue, Nov 22, 2016 at 7:10 PM, Tom Rini <trini@konsulko.com> wrote:
> > On Tue, Nov 22, 2016 at 06:13:31PM +0100, Fabien Parent wrote:
> >
> >> The SPL is unable to load u-boot because the DDR2 is not configured.
> >> Configure the DDR2.
> >>
> >> Signed-off-by: Fabien Parent <fparent@baylibre.com>
> >> ---
> >>
> >> V1 -> V2
> >>
> >>     * New patch
> >>
> >> ---
> >>  include/configs/omapl138_lcdk.h | 42 +++++++++++++++++++++++++++++++++++++++++
> >>  1 file changed, 42 insertions(+)
> >>
> >> diff --git a/include/configs/omapl138_lcdk.h b/include/configs/omapl138_lcdk.h
> >> index ce3a8f4..2cdf892 100644
> >> --- a/include/configs/omapl138_lcdk.h
> >> +++ b/include/configs/omapl138_lcdk.h
> >> @@ -31,6 +31,7 @@
> >>  #define CONFIG_SYS_HZ_CLOCK          clk_get(DAVINCI_AUXCLK_CLKID)
> >>  #define CONFIG_SYS_HZ                        1000
> >>  #define CONFIG_SYS_DA850_PLL_INIT
> >> +#define CONFIG_SYS_DA850_DDR_INIT
> >>  #define CONFIG_SKIP_LOWLEVEL_INIT
> >>  #define CONFIG_SYS_TEXT_BASE         0xc1080000
> >
> > This would be "easy" to move to Kconfig, so please do.
> >
> >> @@ -80,6 +81,47 @@
> >>  #define CONFIG_SYS_DA850_PLL1_PLLM     21
> >>
> >>  /*
> >> + * DDR2 memory configuration
> >> + */
> >> +#define CONFIG_SYS_DA850_DDR2_DDRPHYCR (DV_DDR_PHY_PWRDNEN | \
> >> +                                     DV_DDR_PHY_EXT_STRBEN | \
> >> +                                     (0x5 << DV_DDR_PHY_RD_LATENCY_SHIFT))
> >> +
> >> +#define CONFIG_SYS_DA850_DDR2_SDBCR (                  \
> >> +     (1 << DV_DDR_SDCR_DDR2EN_SHIFT)         | \
> >> +     (1 << DV_DDR_SDCR_DDREN_SHIFT)          | \
> >> +     (1 << DV_DDR_SDCR_SDRAMEN_SHIFT)        | \
> >> +     (1 << DV_DDR_SDCR_BUS_WIDTH_SHIFT)      | \
> >> +     (4 << DV_DDR_SDCR_CL_SHIFT)             | \
> >> +     (3 << DV_DDR_SDCR_IBANK_SHIFT)          | \
> >> +     (2 << DV_DDR_SDCR_PAGESIZE_SHIFT))
> >> +
> >> +/* SDBCR2 is only used if IBANK_POS bit in SDBCR is set */
> >> +#define CONFIG_SYS_DA850_DDR2_SDBCR2 0
> >> +
> >> +#define CONFIG_SYS_DA850_DDR2_SDTIMR (                 \
> >> +     (19 << DV_DDR_SDTMR1_RFC_SHIFT)         | \
> >> +     (1 << DV_DDR_SDTMR1_RP_SHIFT)           | \
> >> +     (1 << DV_DDR_SDTMR1_RCD_SHIFT)          | \
> >> +     (2 << DV_DDR_SDTMR1_WR_SHIFT)           | \
> >> +     (6 << DV_DDR_SDTMR1_RAS_SHIFT)          | \
> >> +     (8 << DV_DDR_SDTMR1_RC_SHIFT)           | \
> >> +     (1 << DV_DDR_SDTMR1_RRD_SHIFT)          | \
> >> +     (1 << DV_DDR_SDTMR1_WTR_SHIFT))
> >> +
> >> +#define CONFIG_SYS_DA850_DDR2_SDTIMR2 (                \
> >> +     (7 << DV_DDR_SDTMR2_RASMAX_SHIFT)       | \
> >> +     (2 << DV_DDR_SDTMR2_XP_SHIFT)           | \
> >> +     (0 << DV_DDR_SDTMR2_ODT_SHIFT)          | \
> >> +     (10 << DV_DDR_SDTMR2_XSNR_SHIFT)        | \
> >> +     (199 << DV_DDR_SDTMR2_XSRD_SHIFT)       | \
> >> +     (1 << DV_DDR_SDTMR2_RTP_SHIFT)          | \
> >> +     (2 << DV_DDR_SDTMR2_CKE_SHIFT))
> >> +
> >> +#define CONFIG_SYS_DA850_DDR2_SDRCR    0x00000492
> >> +#define CONFIG_SYS_DA850_DDR2_PBBPR    0x30
> >
> > This is a little harder.  I think this should be done more like
> > arch/arm/include/asm/arch-omap3/mem.h:#define where we name-space the
> > values that we construct based on the part (maker and size/speed).  Do
> > you have time to look into this migration?  Thanks!
> 
> Given that I don't have a lot of time right now, in the v3 I will just
> move CONFIG_SYS_DA850_DDR_INIT to Kconfig and keep all the config in
> the header file and at a later time once my current work on
> OMAPl138-LCDK is over I will sent a new patchset for all the
> CONFIG_SYS_DA85_DDR* options.

OK, thanks!

-- 
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20161128/3a30b336/attachment.sig>