From: Ryan Tandy <ryan@nardis.ca>
To: Roger Shimizu <rogershimizu@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>, Martin Michlmayr <tbm@cyrius.com>,
Sylver Bruneau <sylver.bruneau@googlemail.com>,
Herbert Valerio Riedel <hvr@gnu.org>,
Florian Fainelli <f.fainelli@gmail.com>,
linux-pm@vger.kernel.org, devicetree@vger.kernel.org,
linux-arm-kernel@lists.infradead.org
Subject: Re: [PATCH v4 1/2] power: reset: add linkstation-reset driver
Date: Sun, 8 Jan 2017 09:02:09 -0800 [thread overview]
Message-ID: <20170108170209.GD573@kiwi.nardis.ca> (raw)
In-Reply-To: <20170107150451.17912-2-rogershimizu@gmail.com>
Hi Roger,
On Sun, Jan 08, 2017 at 12:04:50AM +0900, Roger Shimizu wrote:
>+config POWER_RESET_LINKSTATION
>+ bool "Buffalo Linkstation and its variants reset driver"
>+ depends on OF_GPIO && PLAT_ORION
>+ help
>+ This driver supports power off Buffalo Linkstation / KuroBox Pro
>+ NAS and their variants by sending commands to the micro-controller
>+ which controls the main power.
>+
>+ Say Y if you have a Buffalo Linkstation / KuroBox Pro NAS.
>+
Would it make sense to mention something about these being the
ARM9/orion5x Linkstations? If I understand correctly, the older PPC
Linkstations have a single-byte poweroff command. (Maybe they could even
be supported by qnap-poweroff.)
See arch/powerpc/platforms/embedded6xx/linkstation.c around line 123,
and arch/powerpc/platforms/embedded6xx/ls_uart.c.
WARNING: multiple messages have this Message-ID (diff)
From: ryan@nardis.ca (Ryan Tandy)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v4 1/2] power: reset: add linkstation-reset driver
Date: Sun, 8 Jan 2017 09:02:09 -0800 [thread overview]
Message-ID: <20170108170209.GD573@kiwi.nardis.ca> (raw)
In-Reply-To: <20170107150451.17912-2-rogershimizu@gmail.com>
Hi Roger,
On Sun, Jan 08, 2017 at 12:04:50AM +0900, Roger Shimizu wrote:
>+config POWER_RESET_LINKSTATION
>+ bool "Buffalo Linkstation and its variants reset driver"
>+ depends on OF_GPIO && PLAT_ORION
>+ help
>+ This driver supports power off Buffalo Linkstation / KuroBox Pro
>+ NAS and their variants by sending commands to the micro-controller
>+ which controls the main power.
>+
>+ Say Y if you have a Buffalo Linkstation / KuroBox Pro NAS.
>+
Would it make sense to mention something about these being the
ARM9/orion5x Linkstations? If I understand correctly, the older PPC
Linkstations have a single-byte poweroff command. (Maybe they could even
be supported by qnap-poweroff.)
See arch/powerpc/platforms/embedded6xx/linkstation.c around line 123,
and arch/powerpc/platforms/embedded6xx/ls_uart.c.
next prev parent reply other threads:[~2017-01-08 17:02 UTC|newest]
Thread overview: 68+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-12-05 12:45 [PATCH 0/3] make kurobox-pro be able to shutdown after device-tree migration Roger Shimizu
2016-12-05 12:45 ` [PATCH 1/3] power: reset: make qnap-poweroff flexible on hello magic command to uart1 Roger Shimizu
2016-12-05 12:45 ` [PATCH 2/3] power: reset: make qnap-poweroff flexible on length of power-off command Roger Shimizu
2016-12-05 12:45 ` [PATCH 3/3] power: reset: make qnap-poweroff support kurobox-pro Roger Shimizu
2016-12-06 17:34 ` [PATCH 0/3] make kurobox-pro be able to shutdown after device-tree migration Andrew Lunn
2016-12-07 17:24 ` [PATCH v1 " Roger Shimizu
2016-12-07 17:24 ` [PATCH v1 1/3] power: reset: make qnap-poweroff flexible on hello magic command to uart1 Roger Shimizu
2016-12-07 17:24 ` [PATCH v1 2/3] power: reset: make qnap-poweroff flexible on length of power-off command Roger Shimizu
2016-12-07 17:24 ` [PATCH v1 3/3] power: reset: make qnap-poweroff support kurobox-pro Roger Shimizu
2016-12-07 18:04 ` [PATCH v1 0/3] make kurobox-pro be able to shutdown after device-tree migration Andrew Lunn
2016-12-16 10:05 ` [PATCH v2] power: reset: add linkstation-reset driver Roger Shimizu
2016-12-19 0:34 ` Roger Shimizu
2016-12-19 15:38 ` Sebastian Reichel
2016-12-19 16:03 ` Andrew Lunn
2016-12-19 16:12 ` Roger Shimizu
2016-12-19 17:37 ` Roger Shimizu
[not found] ` <CAEQ9gEnQEHdcA4ox3teOXKcrdf2AAqUMp=A6W6c7nXhk4VrKiw-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2016-12-21 15:59 ` Sebastian Reichel
2016-12-21 16:41 ` Andrew Lunn
[not found] ` <20161221164136.GM30952-g2DYL2Zd6BY@public.gmane.org>
2016-12-22 14:49 ` Sebastian Reichel
2016-12-26 16:13 ` Roger Shimizu
2016-12-27 7:06 ` [PATCH v3 0/3] make kurobox-pro be able to shutdown after device-tree migration Roger Shimizu
2016-12-27 7:06 ` Roger Shimizu
2016-12-27 7:06 ` [PATCH v3 1/3] power: reset: add linkstation-reset driver Roger Shimizu
2016-12-27 7:06 ` Roger Shimizu
[not found] ` <20161227070611.14852-2-rogershimizu-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
2017-01-03 5:19 ` Florian Fainelli
2017-01-03 5:19 ` Florian Fainelli
2017-01-03 13:09 ` Andrew Lunn
2017-01-03 13:09 ` Andrew Lunn
2017-01-03 14:08 ` Roger Shimizu
2017-01-03 14:08 ` Roger Shimizu
[not found] ` <CAEQ9gE=MoQcr3eX0DAxZtvx0FW9pzgkUGjdxKHcsKwH7_+UsUw-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2017-01-03 18:39 ` Florian Fainelli
2017-01-03 18:39 ` Florian Fainelli
2016-12-27 7:06 ` [PATCH v3 2/3] DT: bingdings: power: reset: add linkstation-reset doc Roger Shimizu
2016-12-27 7:06 ` Roger Shimizu
2017-01-03 5:21 ` Florian Fainelli
2017-01-03 5:21 ` Florian Fainelli
2017-01-03 13:12 ` Andrew Lunn
2017-01-03 13:12 ` Andrew Lunn
2017-01-03 14:11 ` Roger Shimizu
2017-01-03 14:11 ` Roger Shimizu
2017-01-03 17:09 ` Rob Herring
2017-01-03 17:09 ` Rob Herring
2017-01-06 12:18 ` Roger Shimizu
2017-01-06 12:18 ` Roger Shimizu
2016-12-27 7:06 ` [PATCH v3 3/3] ARM: DT: add power-off support to linkstation lsgl and kuroboxpro Roger Shimizu
2016-12-27 7:06 ` Roger Shimizu
2017-01-07 15:04 ` [PATCH v4 0/2] make kurobox-pro be able to shutdown after device-tree migration Roger Shimizu
2017-01-07 15:04 ` Roger Shimizu
[not found] ` <20170107150451.17912-1-rogershimizu-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
2017-01-07 15:04 ` [PATCH v4 1/2] power: reset: add linkstation-reset driver Roger Shimizu
2017-01-07 15:04 ` Roger Shimizu
2017-01-08 17:02 ` Ryan Tandy [this message]
2017-01-08 17:02 ` Ryan Tandy
2017-01-09 3:31 ` Roger Shimizu
2017-01-09 3:31 ` Roger Shimizu
2017-01-09 5:43 ` Ryan Tandy
2017-01-09 5:43 ` Ryan Tandy
2017-01-18 12:08 ` Roger Shimizu
2017-01-18 12:08 ` Roger Shimizu
2017-01-19 4:43 ` Sebastian Reichel
2017-01-19 4:43 ` Sebastian Reichel
2017-01-26 15:28 ` Gregory CLEMENT
2017-01-26 15:28 ` Gregory CLEMENT
2017-01-26 15:33 ` Roger Shimizu
2017-01-26 15:33 ` Roger Shimizu
2017-01-27 9:15 ` Gregory CLEMENT
2017-01-27 9:15 ` Gregory CLEMENT
2017-01-07 15:04 ` [PATCH v4 2/2] ARM: DT: add power-off support to linkstation lsgl and kuroboxpro Roger Shimizu
2017-01-07 15:04 ` Roger Shimizu
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20170108170209.GD573@kiwi.nardis.ca \
--to=ryan@nardis.ca \
--cc=andrew@lunn.ch \
--cc=devicetree@vger.kernel.org \
--cc=f.fainelli@gmail.com \
--cc=hvr@gnu.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-pm@vger.kernel.org \
--cc=rogershimizu@gmail.com \
--cc=sylver.bruneau@googlemail.com \
--cc=tbm@cyrius.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.