All of lore.kernel.org
 help / color / mirror / Atom feed
From: "KAVITA MATHUR" <kavitam@cdot.in>
To: ath10k@lists.infradead.org
Subject: ath10k QCA988x firmware not supporting monitor mode
Date: Wed, 1 Mar 2017 10:38:48 +0530	[thread overview]
Message-ID: <20170301050509.M45885@cdot.in> (raw)
In-Reply-To: <20170301050002.M24080@cdot.in>



Hi!

We are using Atheros QCA9880 mPCIe module with ath10k drivers and firmware.

Kernel: 3.12
Backports: 4.4
Firmware:10.2.4.70.59-2

We are not able to run the wlan1 interface in monitor mode. The following error comes
when we do
iw phy phy1 interface add wlan1 type monitor
ifconfig wlan1 up

ath10k_pci 0001:03:00.0: firmware crashed! (uuid n/a)
ath10k_pci 0001:03:00.0: qca988x hw2.0 (0x4100016c, 0x043202ff sub 0000:0000) fw
10.2.4.70.59-2 fwapi 5 bdapi 1 htt-ver 2.1 wmi-op 5 htt-op 2 cal otp max-sta 128 raw 0
hwcrypto 1 features no-p2p,raw-mode
ath10k_pci 0001:03:00.0: debug 0 debugfs 0 tracing 0 dfs 0 testmode 0
ath10k_pci 0001:03:00.0: firmware register dump:
ath10k_pci 0001:03:00.0: [00]: 0x4100016C 0x00000000 0x0097F8D5 0x00000000
ath10k_pci 0001:03:00.0: [04]: 0x00000000 0x00000000 0x00000000 0x00000000
ath10k_pci 0001:03:00.0: [08]: 0x00000000 0x00000000 0x00000000 0x00000000
ath10k_pci 0001:03:00.0: [12]: 0x00000000 0x00000000 0x00000000 0x00000000
ath10k_pci 0001:03:00.0: [16]: 0x00000000 0x00000000 0x00000000 0x0097F8D5
ath10k_pci 0001:03:00.0: [20]: 0x00000000 0x00401930 0x00000000 0x00000000
ath10k_pci 0001:03:00.0: [24]: 0x00000000 0x00000000 0x00000000 0x00000000
ath10k_pci 0001:03:00.0: [28]: 0x00000000 0x00000000 0x00000000 0x00000000
ath10k_pci 0001:03:00.0: [32]: 0x00000000 0x00000000 0x00000000 0x00000000
ath10k_pci 0001:03:00.0: [36]: 0x00000000 0x00000000 0x00000000 0x00000000
ath10k_pci 0001:03:00.0: [40]: 0x00000000 0x00000000 0x00000000 0x00000000
ath10k_pci 0001:03:00.0: [44]: 0x00000000 0x00000000 0x00000000 0x00000000
ath10k_pci 0001:03:00.0: [48]: 0x00000000 0x00000000 0x00000000 0x00000000
ath10k_pci 0001:03:00.0: [52]: 0x00000000 0x00000000 0x00000000 0x00000000
ath10k_pci 0001:03:00.0: [56]: 0x00000000 0x00000000 0x00000000 0x00000000
ath10k_pci 0001:03:00.0: failed to set 2g txpower 0: -108
ath10k_pci 0001:03:00.0: failed to setup tx power 0: -108
ath10k_pci 0001:03:00.0: failed to recalc tx power: -108
------------[ cut here ]------------
WARNING: at fb83c3b8 [verbose debug info unavailable]
Modules linked in: ath10k_pci(O) ath10k_core(O) mac80211(O) ath(O) cfg80211(O) compat(O)
uio_pdrv_genirq
CPU: 0 PID: 17173 Comm: ifconfig Tainted: G           O 3.12.37-rt51+ #23
task: e6415500 ti: ef02a000 task.ti: ef02a000
NIP: fb83c3b8 LR: fb83c3a8 CTR: c00788f0
REGS: ef02bcb0 TRAP: 0700   Tainted: G           O  (3.12.37-rt51+)
MSR: 00029002 <CE,EE,ME>  CR: 84008482  XER: 20000000

GPR00: fb83c3a8 ef02bd60 e6415500 ffffff94 eb865a40 00000152 00000000 00000000
GPR08: 00000000 00000001 00000000 00021002 84ad2e42 10025578 10100000 00000000
GPR16: 00000000 1000acb4 1001d264 1001d264 1001d1f8 ef98200c 00000000 e0e44000
GPR24: e0e44480 ffffffff 00000001 00000000 e0e44704 e0e40000 ffffff94 ef7ccba0
NIP [fb83c3b8] ieee80211_add_virtual_monitor+0xd8/0x1c0 [mac80211]
LR [fb83c3a8] ieee80211_add_virtual_monitor+0xc8/0x1c0 [mac80211]
Call Trace:
[ef02bd60] [fb83c3a8] ieee80211_add_virtual_monitor+0xc8/0x1c0 [mac80211] (unreliable)
[ef02bd80] [fb83d168] ieee80211_do_open+0x4e8/0xa30 [mac80211]
[ef02bdc0] [c04d73a8] __dev_open+0xe8/0x160
[ef02bdf0] [c04d76a0] __dev_change_flags+0xa0/0x180
[ef02be10] [c04d785c] dev_change_flags+0x1c/0x70
[ef02be30] [c057d930] devinet_ioctl+0x600/0x8e0
[ef02be90] [c04ba6f4] sock_ioctl+0x224/0x2e0
[ef02beb0] [c0115150] do_vfs_ioctl+0x410/0x7a0
[ef02bf10] [c0115520] SyS_ioctl+0x40/0x80
[ef02bf40] [c000fb04] ret_from_syscall+0x0/0x3c
--- Exception: c01 at 0xff4ff8c
    LR = 0xffed2c0
Instruction dump:
39200008 913d038c 7fa3eb78 93dd000c 4bffe349 7fe3fb78 7fa4eb78 4bfee2cd
7c690034 5529d97e 7c7e1b78 69290001 <0f090000> 2f890000 7fa3eb78 40de00a0
---[ end trace c9df4859ac192be7 ]---
ieee80211 phy1: Hardware restart was requested
SIOCSIFFLAGS: Cannot send after transport endpoint shutdown

Please help me to set monitor mode on WiFi node.

Disclaimer:

----------

This email and any files transmitted with it are confidential and intended solely for

the use of the individual or entity to whom they are addressed.  If you are not the

intended recipient you are notified that disclosing, copying, distributing or taking

any action in reliance on the contents of this information is strictly prohibited. The

sender does not accept liability for any errors or omissions in the contents of this

message, which arise as a result
------- End of Forwarded Message -------


Thanks & Regards,
कविता माथुर Kavita Mathur 
वरिष्ठ अनुसंधान अभियंता  Senior Research Engineer 
सी-डॉट                      C-DOT
इलैक्ट्रॉनिक्स सिटी फेज़ I         Electronics City Phase I
होसूर रोड, बेंगलूरु               Hosur Road, Bengaluru – 560100
फोन  Ph 080-28529896
Disclaimer:
----------
This email and any files transmitted with it


_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k

  parent reply	other threads:[~2017-03-01  5:15 UTC|newest]

Thread overview: 4+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2017-02-14 11:41 ath10k QCA988x firmware not supporting monitor mode Diganta Jena
     [not found] ` <20170301050002.M24080@cdot.in>
2017-03-01  5:08   ` KAVITA MATHUR [this message]
2017-03-01  5:22     ` Mohammed Shafi Shajakhan
2017-03-01 10:25       ` KAVITA MATHUR

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20170301050509.M45885@cdot.in \
    --to=kavitam@cdot.in \
    --cc=ath10k@lists.infradead.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.