* ath10k QCA988x firmware not supporting monitor mode
@ 2017-02-14 11:41 Diganta Jena
[not found] ` <20170301050002.M24080@cdot.in>
0 siblings, 1 reply; 4+ messages in thread
From: Diganta Jena @ 2017-02-14 11:41 UTC (permalink / raw)
To: ath10k
Hi!
We are using Atheros QCA9880 mPCIe module with ath10k drivers and firmware.
Kernel: 3.12
Backports: 4.4
Firmware:10.2.4.70.59-2
We are not able to run the wlan1 interface in monitor mode. The following error comes
when we do
iw phy phy1 interface add wlan1 type monitor
ifconfig wlan1 up
ath10k_pci 0001:03:00.0: firmware crashed! (uuid n/a)
ath10k_pci 0001:03:00.0: qca988x hw2.0 (0x4100016c, 0x043202ff sub 0000:0000) fw
10.2.4.70.59-2 fwapi 5 bdapi 1 htt-ver 2.1 wmi-op 5 htt-op 2 cal otp max-sta 128 raw 0
hwcrypto 1 features no-p2p,raw-mode
ath10k_pci 0001:03:00.0: debug 0 debugfs 0 tracing 0 dfs 0 testmode 0
ath10k_pci 0001:03:00.0: firmware register dump:
ath10k_pci 0001:03:00.0: [00]: 0x4100016C 0x00000000 0x0097F8D5 0x00000000
ath10k_pci 0001:03:00.0: [04]: 0x00000000 0x00000000 0x00000000 0x00000000
ath10k_pci 0001:03:00.0: [08]: 0x00000000 0x00000000 0x00000000 0x00000000
ath10k_pci 0001:03:00.0: [12]: 0x00000000 0x00000000 0x00000000 0x00000000
ath10k_pci 0001:03:00.0: [16]: 0x00000000 0x00000000 0x00000000 0x0097F8D5
ath10k_pci 0001:03:00.0: [20]: 0x00000000 0x00401930 0x00000000 0x00000000
ath10k_pci 0001:03:00.0: [24]: 0x00000000 0x00000000 0x00000000 0x00000000
ath10k_pci 0001:03:00.0: [28]: 0x00000000 0x00000000 0x00000000 0x00000000
ath10k_pci 0001:03:00.0: [32]: 0x00000000 0x00000000 0x00000000 0x00000000
ath10k_pci 0001:03:00.0: [36]: 0x00000000 0x00000000 0x00000000 0x00000000
ath10k_pci 0001:03:00.0: [40]: 0x00000000 0x00000000 0x00000000 0x00000000
ath10k_pci 0001:03:00.0: [44]: 0x00000000 0x00000000 0x00000000 0x00000000
ath10k_pci 0001:03:00.0: [48]: 0x00000000 0x00000000 0x00000000 0x00000000
ath10k_pci 0001:03:00.0: [52]: 0x00000000 0x00000000 0x00000000 0x00000000
ath10k_pci 0001:03:00.0: [56]: 0x00000000 0x00000000 0x00000000 0x00000000
ath10k_pci 0001:03:00.0: failed to set 2g txpower 0: -108
ath10k_pci 0001:03:00.0: failed to setup tx power 0: -108
ath10k_pci 0001:03:00.0: failed to recalc tx power: -108
------------[ cut here ]------------
WARNING: at fb83c3b8 [verbose debug info unavailable]
Modules linked in: ath10k_pci(O) ath10k_core(O) mac80211(O) ath(O) cfg80211(O) compat(O)
uio_pdrv_genirq
CPU: 0 PID: 17173 Comm: ifconfig Tainted: G O 3.12.37-rt51+ #23
task: e6415500 ti: ef02a000 task.ti: ef02a000
NIP: fb83c3b8 LR: fb83c3a8 CTR: c00788f0
REGS: ef02bcb0 TRAP: 0700 Tainted: G O (3.12.37-rt51+)
MSR: 00029002 <CE,EE,ME> CR: 84008482 XER: 20000000
GPR00: fb83c3a8 ef02bd60 e6415500 ffffff94 eb865a40 00000152 00000000 00000000
GPR08: 00000000 00000001 00000000 00021002 84ad2e42 10025578 10100000 00000000
GPR16: 00000000 1000acb4 1001d264 1001d264 1001d1f8 ef98200c 00000000 e0e44000
GPR24: e0e44480 ffffffff 00000001 00000000 e0e44704 e0e40000 ffffff94 ef7ccba0
NIP [fb83c3b8] ieee80211_add_virtual_monitor+0xd8/0x1c0 [mac80211]
LR [fb83c3a8] ieee80211_add_virtual_monitor+0xc8/0x1c0 [mac80211]
Call Trace:
[ef02bd60] [fb83c3a8] ieee80211_add_virtual_monitor+0xc8/0x1c0 [mac80211] (unreliable)
[ef02bd80] [fb83d168] ieee80211_do_open+0x4e8/0xa30 [mac80211]
[ef02bdc0] [c04d73a8] __dev_open+0xe8/0x160
[ef02bdf0] [c04d76a0] __dev_change_flags+0xa0/0x180
[ef02be10] [c04d785c] dev_change_flags+0x1c/0x70
[ef02be30] [c057d930] devinet_ioctl+0x600/0x8e0
[ef02be90] [c04ba6f4] sock_ioctl+0x224/0x2e0
[ef02beb0] [c0115150] do_vfs_ioctl+0x410/0x7a0
[ef02bf10] [c0115520] SyS_ioctl+0x40/0x80
[ef02bf40] [c000fb04] ret_from_syscall+0x0/0x3c
--- Exception: c01 at 0xff4ff8c
LR = 0xffed2c0
Instruction dump:
39200008 913d038c 7fa3eb78 93dd000c 4bffe349 7fe3fb78 7fa4eb78 4bfee2cd
7c690034 5529d97e 7c7e1b78 69290001 <0f090000> 2f890000 7fa3eb78 40de00a0
---[ end trace c9df4859ac192be7 ]---
ieee80211 phy1: Hardware restart was requested
SIOCSIFFLAGS: Cannot send after transport endpoint shutdown
Thank you
Regards
Diganta Jena
Disclaimer:
----------
This email and any files transmitted with it are confidential and intended solely for
the use of the individual or entity to whom they are addressed. If you are not the
intended recipient you are notified that disclosing, copying, distributing or taking
any action in reliance on the contents of this information is strictly prohibited. The
sender does not accept liability for any errors or omissions in the contents of this
message, which arise as a result
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
^ permalink raw reply [flat|nested] 4+ messages in thread
* ath10k QCA988x firmware not supporting monitor mode
[not found] ` <20170301050002.M24080@cdot.in>
@ 2017-03-01 5:08 ` KAVITA MATHUR
2017-03-01 5:22 ` Mohammed Shafi Shajakhan
0 siblings, 1 reply; 4+ messages in thread
From: KAVITA MATHUR @ 2017-03-01 5:08 UTC (permalink / raw)
To: ath10k
Hi!
We are using Atheros QCA9880 mPCIe module with ath10k drivers and firmware.
Kernel: 3.12
Backports: 4.4
Firmware:10.2.4.70.59-2
We are not able to run the wlan1 interface in monitor mode. The following error comes
when we do
iw phy phy1 interface add wlan1 type monitor
ifconfig wlan1 up
ath10k_pci 0001:03:00.0: firmware crashed! (uuid n/a)
ath10k_pci 0001:03:00.0: qca988x hw2.0 (0x4100016c, 0x043202ff sub 0000:0000) fw
10.2.4.70.59-2 fwapi 5 bdapi 1 htt-ver 2.1 wmi-op 5 htt-op 2 cal otp max-sta 128 raw 0
hwcrypto 1 features no-p2p,raw-mode
ath10k_pci 0001:03:00.0: debug 0 debugfs 0 tracing 0 dfs 0 testmode 0
ath10k_pci 0001:03:00.0: firmware register dump:
ath10k_pci 0001:03:00.0: [00]: 0x4100016C 0x00000000 0x0097F8D5 0x00000000
ath10k_pci 0001:03:00.0: [04]: 0x00000000 0x00000000 0x00000000 0x00000000
ath10k_pci 0001:03:00.0: [08]: 0x00000000 0x00000000 0x00000000 0x00000000
ath10k_pci 0001:03:00.0: [12]: 0x00000000 0x00000000 0x00000000 0x00000000
ath10k_pci 0001:03:00.0: [16]: 0x00000000 0x00000000 0x00000000 0x0097F8D5
ath10k_pci 0001:03:00.0: [20]: 0x00000000 0x00401930 0x00000000 0x00000000
ath10k_pci 0001:03:00.0: [24]: 0x00000000 0x00000000 0x00000000 0x00000000
ath10k_pci 0001:03:00.0: [28]: 0x00000000 0x00000000 0x00000000 0x00000000
ath10k_pci 0001:03:00.0: [32]: 0x00000000 0x00000000 0x00000000 0x00000000
ath10k_pci 0001:03:00.0: [36]: 0x00000000 0x00000000 0x00000000 0x00000000
ath10k_pci 0001:03:00.0: [40]: 0x00000000 0x00000000 0x00000000 0x00000000
ath10k_pci 0001:03:00.0: [44]: 0x00000000 0x00000000 0x00000000 0x00000000
ath10k_pci 0001:03:00.0: [48]: 0x00000000 0x00000000 0x00000000 0x00000000
ath10k_pci 0001:03:00.0: [52]: 0x00000000 0x00000000 0x00000000 0x00000000
ath10k_pci 0001:03:00.0: [56]: 0x00000000 0x00000000 0x00000000 0x00000000
ath10k_pci 0001:03:00.0: failed to set 2g txpower 0: -108
ath10k_pci 0001:03:00.0: failed to setup tx power 0: -108
ath10k_pci 0001:03:00.0: failed to recalc tx power: -108
------------[ cut here ]------------
WARNING: at fb83c3b8 [verbose debug info unavailable]
Modules linked in: ath10k_pci(O) ath10k_core(O) mac80211(O) ath(O) cfg80211(O) compat(O)
uio_pdrv_genirq
CPU: 0 PID: 17173 Comm: ifconfig Tainted: G O 3.12.37-rt51+ #23
task: e6415500 ti: ef02a000 task.ti: ef02a000
NIP: fb83c3b8 LR: fb83c3a8 CTR: c00788f0
REGS: ef02bcb0 TRAP: 0700 Tainted: G O (3.12.37-rt51+)
MSR: 00029002 <CE,EE,ME> CR: 84008482 XER: 20000000
GPR00: fb83c3a8 ef02bd60 e6415500 ffffff94 eb865a40 00000152 00000000 00000000
GPR08: 00000000 00000001 00000000 00021002 84ad2e42 10025578 10100000 00000000
GPR16: 00000000 1000acb4 1001d264 1001d264 1001d1f8 ef98200c 00000000 e0e44000
GPR24: e0e44480 ffffffff 00000001 00000000 e0e44704 e0e40000 ffffff94 ef7ccba0
NIP [fb83c3b8] ieee80211_add_virtual_monitor+0xd8/0x1c0 [mac80211]
LR [fb83c3a8] ieee80211_add_virtual_monitor+0xc8/0x1c0 [mac80211]
Call Trace:
[ef02bd60] [fb83c3a8] ieee80211_add_virtual_monitor+0xc8/0x1c0 [mac80211] (unreliable)
[ef02bd80] [fb83d168] ieee80211_do_open+0x4e8/0xa30 [mac80211]
[ef02bdc0] [c04d73a8] __dev_open+0xe8/0x160
[ef02bdf0] [c04d76a0] __dev_change_flags+0xa0/0x180
[ef02be10] [c04d785c] dev_change_flags+0x1c/0x70
[ef02be30] [c057d930] devinet_ioctl+0x600/0x8e0
[ef02be90] [c04ba6f4] sock_ioctl+0x224/0x2e0
[ef02beb0] [c0115150] do_vfs_ioctl+0x410/0x7a0
[ef02bf10] [c0115520] SyS_ioctl+0x40/0x80
[ef02bf40] [c000fb04] ret_from_syscall+0x0/0x3c
--- Exception: c01 at 0xff4ff8c
LR = 0xffed2c0
Instruction dump:
39200008 913d038c 7fa3eb78 93dd000c 4bffe349 7fe3fb78 7fa4eb78 4bfee2cd
7c690034 5529d97e 7c7e1b78 69290001 <0f090000> 2f890000 7fa3eb78 40de00a0
---[ end trace c9df4859ac192be7 ]---
ieee80211 phy1: Hardware restart was requested
SIOCSIFFLAGS: Cannot send after transport endpoint shutdown
Please help me to set monitor mode on WiFi node.
Disclaimer:
----------
This email and any files transmitted with it are confidential and intended solely for
the use of the individual or entity to whom they are addressed. If you are not the
intended recipient you are notified that disclosing, copying, distributing or taking
any action in reliance on the contents of this information is strictly prohibited. The
sender does not accept liability for any errors or omissions in the contents of this
message, which arise as a result
------- End of Forwarded Message -------
Thanks & Regards,
कविता माथुर Kavita Mathur
वरिष्ठ अनुसंधान अभियंता Senior Research Engineer
सी-डॉट C-DOT
इलैक्ट्रॉनिक्स सिटी फेज़ I Electronics City Phase I
होसूर रोड, बेंगलूरु Hosur Road, Bengaluru – 560100
फोन Ph 080-28529896
Disclaimer:
----------
This email and any files transmitted with it
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: ath10k QCA988x firmware not supporting monitor mode
2017-03-01 5:08 ` KAVITA MATHUR
@ 2017-03-01 5:22 ` Mohammed Shafi Shajakhan
2017-03-01 10:25 ` KAVITA MATHUR
0 siblings, 1 reply; 4+ messages in thread
From: Mohammed Shafi Shajakhan @ 2017-03-01 5:22 UTC (permalink / raw)
To: KAVITA MATHUR; +Cc: ath10k
On Wed, Mar 01, 2017 at 10:38:48AM +0530, KAVITA MATHUR wrote:
>
>
> Hi!
>
> We are using Atheros QCA9880 mPCIe module with ath10k drivers and firmware.
>
> Kernel: 3.12
> Backports: 4.4
> Firmware:10.2.4.70.59-2
[shafi] worth trying updated firmware
https://source.codeaurora.org/quic/qsdk/oss/firmware/ath10k-firmware/plain/ath10k/QCA988X/hw2.0/
>
> We are not able to run the wlan1 interface in monitor mode. The following error comes
> when we do
> iw phy phy1 interface add wlan1 type monitor
> ifconfig wlan1 up
[shafi] can you please confirm the below fix is already available
(its cced to stable though)
https://patchwork.kernel.org/patch/8481281/
and if you see still see the issue in latest backports
http://buildbot.w1.fi/backports-wireless-testing/
please revert back
>
> ath10k_pci 0001:03:00.0: firmware crashed! (uuid n/a)
> ath10k_pci 0001:03:00.0: qca988x hw2.0 (0x4100016c, 0x043202ff sub 0000:0000) fw
> 10.2.4.70.59-2 fwapi 5 bdapi 1 htt-ver 2.1 wmi-op 5 htt-op 2 cal otp max-sta 128 raw 0
> hwcrypto 1 features no-p2p,raw-mode
> ath10k_pci 0001:03:00.0: debug 0 debugfs 0 tracing 0 dfs 0 testmode 0
> ath10k_pci 0001:03:00.0: firmware register dump:
> ath10k_pci 0001:03:00.0: [00]: 0x4100016C 0x00000000 0x0097F8D5 0x00000000
> ath10k_pci 0001:03:00.0: [04]: 0x00000000 0x00000000 0x00000000 0x00000000
> ath10k_pci 0001:03:00.0: [08]: 0x00000000 0x00000000 0x00000000 0x00000000
> ath10k_pci 0001:03:00.0: [12]: 0x00000000 0x00000000 0x00000000 0x00000000
> ath10k_pci 0001:03:00.0: [16]: 0x00000000 0x00000000 0x00000000 0x0097F8D5
> ath10k_pci 0001:03:00.0: [20]: 0x00000000 0x00401930 0x00000000 0x00000000
> ath10k_pci 0001:03:00.0: [24]: 0x00000000 0x00000000 0x00000000 0x00000000
> ath10k_pci 0001:03:00.0: [28]: 0x00000000 0x00000000 0x00000000 0x00000000
> ath10k_pci 0001:03:00.0: [32]: 0x00000000 0x00000000 0x00000000 0x00000000
> ath10k_pci 0001:03:00.0: [36]: 0x00000000 0x00000000 0x00000000 0x00000000
> ath10k_pci 0001:03:00.0: [40]: 0x00000000 0x00000000 0x00000000 0x00000000
> ath10k_pci 0001:03:00.0: [44]: 0x00000000 0x00000000 0x00000000 0x00000000
> ath10k_pci 0001:03:00.0: [48]: 0x00000000 0x00000000 0x00000000 0x00000000
> ath10k_pci 0001:03:00.0: [52]: 0x00000000 0x00000000 0x00000000 0x00000000
> ath10k_pci 0001:03:00.0: [56]: 0x00000000 0x00000000 0x00000000 0x00000000
> ath10k_pci 0001:03:00.0: failed to set 2g txpower 0: -108
> ath10k_pci 0001:03:00.0: failed to setup tx power 0: -108
> ath10k_pci 0001:03:00.0: failed to recalc tx power: -108
> ------------[ cut here ]------------
> WARNING: at fb83c3b8 [verbose debug info unavailable]
> Modules linked in: ath10k_pci(O) ath10k_core(O) mac80211(O) ath(O) cfg80211(O) compat(O)
> uio_pdrv_genirq
> CPU: 0 PID: 17173 Comm: ifconfig Tainted: G O 3.12.37-rt51+ #23
> task: e6415500 ti: ef02a000 task.ti: ef02a000
> NIP: fb83c3b8 LR: fb83c3a8 CTR: c00788f0
> REGS: ef02bcb0 TRAP: 0700 Tainted: G O (3.12.37-rt51+)
> MSR: 00029002 <CE,EE,ME> CR: 84008482 XER: 20000000
>
> GPR00: fb83c3a8 ef02bd60 e6415500 ffffff94 eb865a40 00000152 00000000 00000000
> GPR08: 00000000 00000001 00000000 00021002 84ad2e42 10025578 10100000 00000000
> GPR16: 00000000 1000acb4 1001d264 1001d264 1001d1f8 ef98200c 00000000 e0e44000
> GPR24: e0e44480 ffffffff 00000001 00000000 e0e44704 e0e40000 ffffff94 ef7ccba0
> NIP [fb83c3b8] ieee80211_add_virtual_monitor+0xd8/0x1c0 [mac80211]
> LR [fb83c3a8] ieee80211_add_virtual_monitor+0xc8/0x1c0 [mac80211]
> Call Trace:
> [ef02bd60] [fb83c3a8] ieee80211_add_virtual_monitor+0xc8/0x1c0 [mac80211] (unreliable)
> [ef02bd80] [fb83d168] ieee80211_do_open+0x4e8/0xa30 [mac80211]
> [ef02bdc0] [c04d73a8] __dev_open+0xe8/0x160
> [ef02bdf0] [c04d76a0] __dev_change_flags+0xa0/0x180
> [ef02be10] [c04d785c] dev_change_flags+0x1c/0x70
> [ef02be30] [c057d930] devinet_ioctl+0x600/0x8e0
> [ef02be90] [c04ba6f4] sock_ioctl+0x224/0x2e0
> [ef02beb0] [c0115150] do_vfs_ioctl+0x410/0x7a0
> [ef02bf10] [c0115520] SyS_ioctl+0x40/0x80
> [ef02bf40] [c000fb04] ret_from_syscall+0x0/0x3c
> --- Exception: c01 at 0xff4ff8c
> LR = 0xffed2c0
> Instruction dump:
> 39200008 913d038c 7fa3eb78 93dd000c 4bffe349 7fe3fb78 7fa4eb78 4bfee2cd
> 7c690034 5529d97e 7c7e1b78 69290001 <0f090000> 2f890000 7fa3eb78 40de00a0
> ---[ end trace c9df4859ac192be7 ]---
> ieee80211 phy1: Hardware restart was requested
> SIOCSIFFLAGS: Cannot send after transport endpoint shutdown
>
> Please help me to set monitor mode on WiFi node.
>
> Disclaimer:
>
> ----------
>
> This email and any files transmitted with it are confidential and intended solely for
>
> the use of the individual or entity to whom they are addressed. If you are not the
>
> intended recipient you are notified that disclosing, copying, distributing or taking
>
> any action in reliance on the contents of this information is strictly prohibited. The
>
> sender does not accept liability for any errors or omissions in the contents of this
>
> message, which arise as a result
> ------- End of Forwarded Message -------
>
>
> Thanks & Regards,
> कविता माथुर Kavita Mathur
> वरिष्ठ अनुसंधान अभियंता Senior Research Engineer
> सी-डॉट C-DOT
> इलैक्ट्रॉनिक्स सिटी फेज़ I Electronics City Phase I
> होसूर रोड, बेंगलूरु Hosur Road, Bengaluru – 560100
> फोन Ph 080-28529896
> Disclaimer:
> ----------
> This email and any files transmitted with it
>
>
> _______________________________________________
> ath10k mailing list
> ath10k@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/ath10k
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: ath10k QCA988x firmware not supporting monitor mode
2017-03-01 5:22 ` Mohammed Shafi Shajakhan
@ 2017-03-01 10:25 ` KAVITA MATHUR
0 siblings, 0 replies; 4+ messages in thread
From: KAVITA MATHUR @ 2017-03-01 10:25 UTC (permalink / raw)
To: Mohammed Shafi Shajakhan; +Cc: ath10k
Hi,
Thanks a lot..
Now I am able to set monitor mode after applying the patch and latest firmware.
Thanks & Regards,
Kavita
On Wed, 1 Mar 2017 10:52:42 +0530, Mohammed Shafi Shajakhan wrote
> On Wed, Mar 01, 2017 at 10:38:48AM +0530, KAVITA MATHUR wrote:
> >
> >
> > Hi!
> >
> > We are using Atheros QCA9880 mPCIe module with ath10k drivers and firmware.
> >
> > Kernel: 3.12
> > Backports: 4.4
> > Firmware:10.2.4.70.59-2
>
> [shafi] worth trying updated firmware
>
https://source.codeaurora.org/quic/qsdk/oss/firmware/ath10k-firmware/plain/ath10k/QCA988X/hw2.0/
>
> >
> > We are not able to run the wlan1 interface in monitor mode. The following error comes
> > when we do
> > iw phy phy1 interface add wlan1 type monitor
> > ifconfig wlan1 up
>
> [shafi] can you please confirm the below fix is already available
> (its cced to stable though)
> https://patchwork.kernel.org/patch/8481281/
>
> and if you see still see the issue in latest backports
> http://buildbot.w1.fi/backports-wireless-testing/
>
> please revert back
>
> >
> > ath10k_pci 0001:03:00.0: firmware crashed! (uuid n/a)
> > ath10k_pci 0001:03:00.0: qca988x hw2.0 (0x4100016c, 0x043202ff sub 0000:0000) fw
> > 10.2.4.70.59-2 fwapi 5 bdapi 1 htt-ver 2.1 wmi-op 5 htt-op 2 cal otp max-sta 128 raw 0
> > hwcrypto 1 features no-p2p,raw-mode
> > ath10k_pci 0001:03:00.0: debug 0 debugfs 0 tracing 0 dfs 0 testmode 0
> > ath10k_pci 0001:03:00.0: firmware register dump:
> > ath10k_pci 0001:03:00.0: [00]: 0x4100016C 0x00000000 0x0097F8D5 0x00000000
> > ath10k_pci 0001:03:00.0: [04]: 0x00000000 0x00000000 0x00000000 0x00000000
> > ath10k_pci 0001:03:00.0: [08]: 0x00000000 0x00000000 0x00000000 0x00000000
> > ath10k_pci 0001:03:00.0: [12]: 0x00000000 0x00000000 0x00000000 0x00000000
> > ath10k_pci 0001:03:00.0: [16]: 0x00000000 0x00000000 0x00000000 0x0097F8D5
> > ath10k_pci 0001:03:00.0: [20]: 0x00000000 0x00401930 0x00000000 0x00000000
> > ath10k_pci 0001:03:00.0: [24]: 0x00000000 0x00000000 0x00000000 0x00000000
> > ath10k_pci 0001:03:00.0: [28]: 0x00000000 0x00000000 0x00000000 0x00000000
> > ath10k_pci 0001:03:00.0: [32]: 0x00000000 0x00000000 0x00000000 0x00000000
> > ath10k_pci 0001:03:00.0: [36]: 0x00000000 0x00000000 0x00000000 0x00000000
> > ath10k_pci 0001:03:00.0: [40]: 0x00000000 0x00000000 0x00000000 0x00000000
> > ath10k_pci 0001:03:00.0: [44]: 0x00000000 0x00000000 0x00000000 0x00000000
> > ath10k_pci 0001:03:00.0: [48]: 0x00000000 0x00000000 0x00000000 0x00000000
> > ath10k_pci 0001:03:00.0: [52]: 0x00000000 0x00000000 0x00000000 0x00000000
> > ath10k_pci 0001:03:00.0: [56]: 0x00000000 0x00000000 0x00000000 0x00000000
> > ath10k_pci 0001:03:00.0: failed to set 2g txpower 0: -108
> > ath10k_pci 0001:03:00.0: failed to setup tx power 0: -108
> > ath10k_pci 0001:03:00.0: failed to recalc tx power: -108
> > ------------[ cut here ]------------
> > WARNING: at fb83c3b8 [verbose debug info unavailable]
> > Modules linked in: ath10k_pci(O) ath10k_core(O) mac80211(O) ath(O) cfg80211(O) compat(O)
> > uio_pdrv_genirq
> > CPU: 0 PID: 17173 Comm: ifconfig Tainted: G O 3.12.37-rt51+ #23
> > task: e6415500 ti: ef02a000 task.ti: ef02a000
> > NIP: fb83c3b8 LR: fb83c3a8 CTR: c00788f0
> > REGS: ef02bcb0 TRAP: 0700 Tainted: G O (3.12.37-rt51+)
> > MSR: 00029002 <CE,EE,ME> CR: 84008482 XER: 20000000
> >
> > GPR00: fb83c3a8 ef02bd60 e6415500 ffffff94 eb865a40 00000152 00000000 00000000
> > GPR08: 00000000 00000001 00000000 00021002 84ad2e42 10025578 10100000 00000000
> > GPR16: 00000000 1000acb4 1001d264 1001d264 1001d1f8 ef98200c 00000000 e0e44000
> > GPR24: e0e44480 ffffffff 00000001 00000000 e0e44704 e0e40000 ffffff94 ef7ccba0
> > NIP [fb83c3b8] ieee80211_add_virtual_monitor+0xd8/0x1c0 [mac80211]
> > LR [fb83c3a8] ieee80211_add_virtual_monitor+0xc8/0x1c0 [mac80211]
> > Call Trace:
> > [ef02bd60] [fb83c3a8] ieee80211_add_virtual_monitor+0xc8/0x1c0 [mac80211] (unreliable)
> > [ef02bd80] [fb83d168] ieee80211_do_open+0x4e8/0xa30 [mac80211]
> > [ef02bdc0] [c04d73a8] __dev_open+0xe8/0x160
> > [ef02bdf0] [c04d76a0] __dev_change_flags+0xa0/0x180
> > [ef02be10] [c04d785c] dev_change_flags+0x1c/0x70
> > [ef02be30] [c057d930] devinet_ioctl+0x600/0x8e0
> > [ef02be90] [c04ba6f4] sock_ioctl+0x224/0x2e0
> > [ef02beb0] [c0115150] do_vfs_ioctl+0x410/0x7a0
> > [ef02bf10] [c0115520] SyS_ioctl+0x40/0x80
> > [ef02bf40] [c000fb04] ret_from_syscall+0x0/0x3c
> > --- Exception: c01 at 0xff4ff8c
> > LR = 0xffed2c0
> > Instruction dump:
> > 39200008 913d038c 7fa3eb78 93dd000c 4bffe349 7fe3fb78 7fa4eb78 4bfee2cd
> > 7c690034 5529d97e 7c7e1b78 69290001 <0f090000> 2f890000 7fa3eb78 40de00a0
> > ---[ end trace c9df4859ac192be7 ]---
> > ieee80211 phy1: Hardware restart was requested
> > SIOCSIFFLAGS: Cannot send after transport endpoint shutdown
> >
> > Please help me to set monitor mode on WiFi node.
> >
> > Disclaimer:
> >
> > ----------
> >
> > This email and any files transmitted with it are confidential and intended solely for
> >
> > the use of the individual or entity to whom they are addressed. If you are not the
> >
> > intended recipient you are notified that disclosing, copying, distributing or taking
> >
> > any action in reliance on the contents of this information is strictly prohibited. The
> >
> > sender does not accept liability for any errors or omissions in the contents of this
> >
> > message, which arise as a result
> > ------- End of Forwarded Message -------
> >
> >
> > Thanks & Regards,
> > कविता माथुर Kavita Mathur
> > वरिष्ठ अनुसंधान अभियंता Senior Research Engineer
> > सी-डॉट C-DOT
> > इलैक्ट्रॉनिक्स सिटी फेज़ I Electronics City Phase I
> > होसूर रोड, बेंगलूरु Hosur Road, Bengaluru – 560100
> > फोन Ph 080-28529896
> > Disclaimer:
> > ----------
> > This email and any files transmitted with it
> >
> >
> > _______________________________________________
> > ath10k mailing list
> > ath10k@lists.infradead.org
> > http://lists.infradead.org/mailman/listinfo/ath10k
Thanks & Regards,
कविता माथुर Kavita Mathur
वरिष्ठ अनुसंधान अभियंता Senior Research Engineer
सी-डॉट C-DOT
इलैक्ट्रॉनिक्स सिटी फेज़ I Electronics City Phase I
होसूर रोड, बेंगलूरु Hosur Road, Bengaluru – 560100
फोन Ph 080-28529896
Disclaimer:
----------
This email and any files transmitted with it
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2017-03-01 10:31 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2017-02-14 11:41 ath10k QCA988x firmware not supporting monitor mode Diganta Jena
[not found] ` <20170301050002.M24080@cdot.in>
2017-03-01 5:08 ` KAVITA MATHUR
2017-03-01 5:22 ` Mohammed Shafi Shajakhan
2017-03-01 10:25 ` KAVITA MATHUR
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.