[PATCH 1/2] ARM: dts: BCM5301X: Specify serial console parameters

[PATCH 1/2] ARM: dts: BCM5301X: Specify serial console parameters

[Rafał Miłecki]

From: Rafa? Mi?ecki <rafal@milecki.pl>

This adds baud rate, parity & number of data bits. It's required to get
serial working correctly.

Signed-off-by: Rafa? Mi?ecki <rafal@milecki.pl>
---
 arch/arm/boot/dts/bcm5301x.dtsi | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/bcm5301x.dtsi b/arch/arm/boot/dts/bcm5301x.dtsi
index 8fd1ef9f0c2d..468107166a6f 100644
--- a/arch/arm/boot/dts/bcm5301x.dtsi
+++ b/arch/arm/boot/dts/bcm5301x.dtsi
@@ -18,8 +18,12 @@
 / {
 	interrupt-parent = <&gic>;
 
+	aliases {
+		serial0 = &uart0;
+	};
+
 	chosen {
-		stdout-path = &uart0;
+		stdout-path = "serial0:115200n8";
 	};
 
 	chipcommonA {
-- 
2.11.0

[PATCH 1/2] ARM: dts: BCM5301X: Specify serial console parameters

[Rafał Miłecki]

From: Rafał Miłecki <rafal-g1n6cQUeyibVItvQsEIGlw@public.gmane.org>

This adds baud rate, parity & number of data bits. It's required to get
serial working correctly.

Signed-off-by: Rafał Miłecki <rafal-g1n6cQUeyibVItvQsEIGlw@public.gmane.org>
---
 arch/arm/boot/dts/bcm5301x.dtsi | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/bcm5301x.dtsi b/arch/arm/boot/dts/bcm5301x.dtsi
index 8fd1ef9f0c2d..468107166a6f 100644
--- a/arch/arm/boot/dts/bcm5301x.dtsi
+++ b/arch/arm/boot/dts/bcm5301x.dtsi
@@ -18,8 +18,12 @@
 / {
 	interrupt-parent = <&gic>;
 
+	aliases {
+		serial0 = &uart0;
+	};
+
 	chosen {
-		stdout-path = &uart0;
+		stdout-path = "serial0:115200n8";
 	};
 
 	chipcommonA {
-- 
2.11.0

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 2/2] ARM: dts: BCM53573: Specify serial console parameters

[Rafał Miłecki]

From: Rafa? Mi?ecki <rafal@milecki.pl>

This adds baud rate, parity & number of data bits. It's required to get
serial working correctly.

Signed-off-by: Rafa? Mi?ecki <rafal@milecki.pl>
---
 arch/arm/boot/dts/bcm53573.dtsi | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/bcm53573.dtsi b/arch/arm/boot/dts/bcm53573.dtsi
index 71ce23e46d30..eae623f76401 100644
--- a/arch/arm/boot/dts/bcm53573.dtsi
+++ b/arch/arm/boot/dts/bcm53573.dtsi
@@ -13,8 +13,12 @@
 / {
 	interrupt-parent = <&gic>;
 
+	aliases {
+		serial0 = &uart0;
+	};
+
 	chosen {
-		stdout-path = &uart0;
+		stdout-path = "serial0:115200n8";
 	};
 
 	cpus {
-- 
2.11.0

[PATCH 2/2] ARM: dts: BCM53573: Specify serial console parameters

[Rafał Miłecki]

From: Rafał Miłecki <rafal-g1n6cQUeyibVItvQsEIGlw@public.gmane.org>

This adds baud rate, parity & number of data bits. It's required to get
serial working correctly.

Signed-off-by: Rafał Miłecki <rafal-g1n6cQUeyibVItvQsEIGlw@public.gmane.org>
---
 arch/arm/boot/dts/bcm53573.dtsi | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/bcm53573.dtsi b/arch/arm/boot/dts/bcm53573.dtsi
index 71ce23e46d30..eae623f76401 100644
--- a/arch/arm/boot/dts/bcm53573.dtsi
+++ b/arch/arm/boot/dts/bcm53573.dtsi
@@ -13,8 +13,12 @@
 / {
 	interrupt-parent = <&gic>;
 
+	aliases {
+		serial0 = &uart0;
+	};
+
 	chosen {
-		stdout-path = &uart0;
+		stdout-path = "serial0:115200n8";
 	};
 
 	cpus {
-- 
2.11.0

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 1/2] ARM: dts: BCM5301X: Specify serial console parameters

[Andrew Lunn]

On Tue, Mar 14, 2017 at 08:58:29AM +0100, Rafa?? Mi??ecki wrote:
> From: Rafa?? Mi??ecki <rafal@milecki.pl>
> 
> This adds baud rate, parity & number of data bits. It's required to get
> serial working correctly.
> 
> Signed-off-by: Rafa?? Mi??ecki <rafal@milecki.pl>
> ---
>  arch/arm/boot/dts/bcm5301x.dtsi | 6 +++++-
>  1 file changed, 5 insertions(+), 1 deletion(-)
> 
> diff --git a/arch/arm/boot/dts/bcm5301x.dtsi b/arch/arm/boot/dts/bcm5301x.dtsi
> index 8fd1ef9f0c2d..468107166a6f 100644
> --- a/arch/arm/boot/dts/bcm5301x.dtsi
> +++ b/arch/arm/boot/dts/bcm5301x.dtsi
> @@ -18,8 +18,12 @@
>  / {
>  	interrupt-parent = <&gic>;
>  
> +	aliases {
> +		serial0 = &uart0;
> +	};
> +
>  	chosen {
> -		stdout-path = &uart0;
> +		stdout-path = "serial0:115200n8";
>  	};

Hi Rafal

The alias is fine. But putting the stdout-path here is unusual. Which
serial port is used for console is board specific, where as
bcm5301x.dtsi is very generic, it describes the SoC, not a board.  If
you look at other .dtsi files, those that specify stdout-path contain
properties which are common to a range of similar boards.

	   Andrew

Re: [PATCH 1/2] ARM: dts: BCM5301X: Specify serial console parameters

[Andrew Lunn]

On Tue, Mar 14, 2017 at 08:58:29AM +0100, Rafa?? Mi??ecki wrote:
> From: Rafa?? Mi??ecki <rafal-g1n6cQUeyibVItvQsEIGlw@public.gmane.org>
> 
> This adds baud rate, parity & number of data bits. It's required to get
> serial working correctly.
> 
> Signed-off-by: Rafa?? Mi??ecki <rafal-g1n6cQUeyibVItvQsEIGlw@public.gmane.org>
> ---
>  arch/arm/boot/dts/bcm5301x.dtsi | 6 +++++-
>  1 file changed, 5 insertions(+), 1 deletion(-)
> 
> diff --git a/arch/arm/boot/dts/bcm5301x.dtsi b/arch/arm/boot/dts/bcm5301x.dtsi
> index 8fd1ef9f0c2d..468107166a6f 100644
> --- a/arch/arm/boot/dts/bcm5301x.dtsi
> +++ b/arch/arm/boot/dts/bcm5301x.dtsi
> @@ -18,8 +18,12 @@
>  / {
>  	interrupt-parent = <&gic>;
>  
> +	aliases {
> +		serial0 = &uart0;
> +	};
> +
>  	chosen {
> -		stdout-path = &uart0;
> +		stdout-path = "serial0:115200n8";
>  	};

Hi Rafal

The alias is fine. But putting the stdout-path here is unusual. Which
serial port is used for console is board specific, where as
bcm5301x.dtsi is very generic, it describes the SoC, not a board.  If
you look at other .dtsi files, those that specify stdout-path contain
properties which are common to a range of similar boards.

	   Andrew
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 1/2] ARM: dts: BCM5301X: Specify serial console parameters

[Rafał Miłecki]

On 03/14/2017 01:26 PM, Andrew Lunn wrote:
> On Tue, Mar 14, 2017 at 08:58:29AM +0100, Rafa?? Mi??ecki wrote:
>> From: Rafa?? Mi??ecki <rafal@milecki.pl>
>>
>> This adds baud rate, parity & number of data bits. It's required to get
>> serial working correctly.
>>
>> Signed-off-by: Rafa?? Mi??ecki <rafal@milecki.pl>
>> ---
>>  arch/arm/boot/dts/bcm5301x.dtsi | 6 +++++-
>>  1 file changed, 5 insertions(+), 1 deletion(-)
>>
>> diff --git a/arch/arm/boot/dts/bcm5301x.dtsi b/arch/arm/boot/dts/bcm5301x.dtsi
>> index 8fd1ef9f0c2d..468107166a6f 100644
>> --- a/arch/arm/boot/dts/bcm5301x.dtsi
>> +++ b/arch/arm/boot/dts/bcm5301x.dtsi
>> @@ -18,8 +18,12 @@
>>  / {
>>  	interrupt-parent = <&gic>;
>>
>> +	aliases {
>> +		serial0 = &uart0;
>> +	};
>> +
>>  	chosen {
>> -		stdout-path = &uart0;
>> +		stdout-path = "serial0:115200n8";
>>  	};
>
> Hi Rafal
>
> The alias is fine. But putting the stdout-path here is unusual. Which
> serial port is used for console is board specific, where as
> bcm5301x.dtsi is very generic, it describes the SoC, not a board.  If
> you look at other .dtsi files, those that specify stdout-path contain
> properties which are common to a range of similar boards.

So far I've never seen any board using other uart. Also uart0 is disabled by
default and we enable it per board family (BCM4708 / BCM47081 / BCM4709 /
BCM47094). I think it's just more practical to have simple DTS that covers
99,9% boards by default and handled that margin of devices separately.

We already got a lot of duplicated code for enabling uart0, see:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=7b790d3b2943bf8e7e7bafe184008bd6451fe0bd

Jon Mason from Broadcom who knows this hardware and designs very well confirmed
it's a sane/safe assumption.

Re: [PATCH 1/2] ARM: dts: BCM5301X: Specify serial console parameters

[Rafał Miłecki]

On 03/14/2017 01:26 PM, Andrew Lunn wrote:
> On Tue, Mar 14, 2017 at 08:58:29AM +0100, Rafa?? Mi??ecki wrote:
>> From: Rafa?? Mi??ecki <rafal-g1n6cQUeyibVItvQsEIGlw@public.gmane.org>
>>
>> This adds baud rate, parity & number of data bits. It's required to get
>> serial working correctly.
>>
>> Signed-off-by: Rafa?? Mi??ecki <rafal-g1n6cQUeyibVItvQsEIGlw@public.gmane.org>
>> ---
>>  arch/arm/boot/dts/bcm5301x.dtsi | 6 +++++-
>>  1 file changed, 5 insertions(+), 1 deletion(-)
>>
>> diff --git a/arch/arm/boot/dts/bcm5301x.dtsi b/arch/arm/boot/dts/bcm5301x.dtsi
>> index 8fd1ef9f0c2d..468107166a6f 100644
>> --- a/arch/arm/boot/dts/bcm5301x.dtsi
>> +++ b/arch/arm/boot/dts/bcm5301x.dtsi
>> @@ -18,8 +18,12 @@
>>  / {
>>  	interrupt-parent = <&gic>;
>>
>> +	aliases {
>> +		serial0 = &uart0;
>> +	};
>> +
>>  	chosen {
>> -		stdout-path = &uart0;
>> +		stdout-path = "serial0:115200n8";
>>  	};
>
> Hi Rafal
>
> The alias is fine. But putting the stdout-path here is unusual. Which
> serial port is used for console is board specific, where as
> bcm5301x.dtsi is very generic, it describes the SoC, not a board.  If
> you look at other .dtsi files, those that specify stdout-path contain
> properties which are common to a range of similar boards.

So far I've never seen any board using other uart. Also uart0 is disabled by
default and we enable it per board family (BCM4708 / BCM47081 / BCM4709 /
BCM47094). I think it's just more practical to have simple DTS that covers
99,9% boards by default and handled that margin of devices separately.

We already got a lot of duplicated code for enabling uart0, see:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=7b790d3b2943bf8e7e7bafe184008bd6451fe0bd

Jon Mason from Broadcom who knows this hardware and designs very well confirmed
it's a sane/safe assumption.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 1/2] ARM: dts: BCM5301X: Specify serial console parameters

[Rafał Miłecki]

On 03/14/2017 01:32 PM, Rafa? Mi?ecki wrote:
> On 03/14/2017 01:26 PM, Andrew Lunn wrote:
>> On Tue, Mar 14, 2017 at 08:58:29AM +0100, Rafa?? Mi??ecki wrote:
>>> From: Rafa?? Mi??ecki <rafal@milecki.pl>
>>>
>>> This adds baud rate, parity & number of data bits. It's required to get
>>> serial working correctly.
>>>
>>> Signed-off-by: Rafa?? Mi??ecki <rafal@milecki.pl>
>>> ---
>>>  arch/arm/boot/dts/bcm5301x.dtsi | 6 +++++-
>>>  1 file changed, 5 insertions(+), 1 deletion(-)
>>>
>>> diff --git a/arch/arm/boot/dts/bcm5301x.dtsi b/arch/arm/boot/dts/bcm5301x.dtsi
>>> index 8fd1ef9f0c2d..468107166a6f 100644
>>> --- a/arch/arm/boot/dts/bcm5301x.dtsi
>>> +++ b/arch/arm/boot/dts/bcm5301x.dtsi
>>> @@ -18,8 +18,12 @@
>>>  / {
>>>      interrupt-parent = <&gic>;
>>>
>>> +    aliases {
>>> +        serial0 = &uart0;
>>> +    };
>>> +
>>>      chosen {
>>> -        stdout-path = &uart0;
>>> +        stdout-path = "serial0:115200n8";
>>>      };
>>
>> Hi Rafal
>>
>> The alias is fine. But putting the stdout-path here is unusual. Which
>> serial port is used for console is board specific, where as
>> bcm5301x.dtsi is very generic, it describes the SoC, not a board.  If
>> you look at other .dtsi files, those that specify stdout-path contain
>> properties which are common to a range of similar boards.
>
> So far I've never seen any board using other uart. Also uart0 is disabled by
> default and we enable it per board family (BCM4708 / BCM47081 / BCM4709 /
> BCM47094). I think it's just more practical to have simple DTS that covers
> 99,9% boards by default and handled that margin of devices separately.
>
> We already got a lot of duplicated code for enabling uart0, see:
> https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=7b790d3b2943bf8e7e7bafe184008bd6451fe0bd
>
> Jon Mason from Broadcom who knows this hardware and designs very well confirmed
> it's a sane/safe assumption.

That was supposed to be "any other uart or parameters".

Re: [PATCH 1/2] ARM: dts: BCM5301X: Specify serial console parameters

[Rafał Miłecki]

On 03/14/2017 01:32 PM, Rafał Miłecki wrote:
> On 03/14/2017 01:26 PM, Andrew Lunn wrote:
>> On Tue, Mar 14, 2017 at 08:58:29AM +0100, Rafa?? Mi??ecki wrote:
>>> From: Rafa?? Mi??ecki <rafal@milecki.pl>
>>>
>>> This adds baud rate, parity & number of data bits. It's required to get
>>> serial working correctly.
>>>
>>> Signed-off-by: Rafa?? Mi??ecki <rafal@milecki.pl>
>>> ---
>>>  arch/arm/boot/dts/bcm5301x.dtsi | 6 +++++-
>>>  1 file changed, 5 insertions(+), 1 deletion(-)
>>>
>>> diff --git a/arch/arm/boot/dts/bcm5301x.dtsi b/arch/arm/boot/dts/bcm5301x.dtsi
>>> index 8fd1ef9f0c2d..468107166a6f 100644
>>> --- a/arch/arm/boot/dts/bcm5301x.dtsi
>>> +++ b/arch/arm/boot/dts/bcm5301x.dtsi
>>> @@ -18,8 +18,12 @@
>>>  / {
>>>      interrupt-parent = <&gic>;
>>>
>>> +    aliases {
>>> +        serial0 = &uart0;
>>> +    };
>>> +
>>>      chosen {
>>> -        stdout-path = &uart0;
>>> +        stdout-path = "serial0:115200n8";
>>>      };
>>
>> Hi Rafal
>>
>> The alias is fine. But putting the stdout-path here is unusual. Which
>> serial port is used for console is board specific, where as
>> bcm5301x.dtsi is very generic, it describes the SoC, not a board.  If
>> you look at other .dtsi files, those that specify stdout-path contain
>> properties which are common to a range of similar boards.
>
> So far I've never seen any board using other uart. Also uart0 is disabled by
> default and we enable it per board family (BCM4708 / BCM47081 / BCM4709 /
> BCM47094). I think it's just more practical to have simple DTS that covers
> 99,9% boards by default and handled that margin of devices separately.
>
> We already got a lot of duplicated code for enabling uart0, see:
> https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=7b790d3b2943bf8e7e7bafe184008bd6451fe0bd
>
> Jon Mason from Broadcom who knows this hardware and designs very well confirmed
> it's a sane/safe assumption.

That was supposed to be "any other uart or parameters".

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 1/2] ARM: dts: BCM5301X: Specify serial console parameters

[Andrew Lunn]

> >The alias is fine. But putting the stdout-path here is unusual. Which
> >serial port is used for console is board specific, where as
> >bcm5301x.dtsi is very generic, it describes the SoC, not a board.  If
> >you look at other .dtsi files, those that specify stdout-path contain
> >properties which are common to a range of similar boards.
> 
> So far I've never seen any board using other uart. Also uart0 is disabled by
> default and we enable it per board family (BCM4708 / BCM47081 / BCM4709 /
> BCM47094). I think it's just more practical to have simple DTS that covers
> 99,9% boards by default and handled that margin of devices separately.
> 
> We already got a lot of duplicated code for enabling uart0, see:
> https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=7b790d3b2943bf8e7e7bafe184008bd6451fe0bd
> 
> Jon Mason from Broadcom who knows this hardware and designs very well confirmed
> it's a sane/safe assumption.

I don't disagree with you, it does make sense. But it is just
different to every other SoC .dtsi file Linux has. And we try to avoid
things being different.

It is down to Florian to decide, as maintainer.

   Andrew

Re: [PATCH 1/2] ARM: dts: BCM5301X: Specify serial console parameters

[Andrew Lunn]

> >The alias is fine. But putting the stdout-path here is unusual. Which
> >serial port is used for console is board specific, where as
> >bcm5301x.dtsi is very generic, it describes the SoC, not a board.  If
> >you look at other .dtsi files, those that specify stdout-path contain
> >properties which are common to a range of similar boards.
> 
> So far I've never seen any board using other uart. Also uart0 is disabled by
> default and we enable it per board family (BCM4708 / BCM47081 / BCM4709 /
> BCM47094). I think it's just more practical to have simple DTS that covers
> 99,9% boards by default and handled that margin of devices separately.
> 
> We already got a lot of duplicated code for enabling uart0, see:
> https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=7b790d3b2943bf8e7e7bafe184008bd6451fe0bd
> 
> Jon Mason from Broadcom who knows this hardware and designs very well confirmed
> it's a sane/safe assumption.

I don't disagree with you, it does make sense. But it is just
different to every other SoC .dtsi file Linux has. And we try to avoid
things being different.

It is down to Florian to decide, as maintainer.

   Andrew
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 1/2] ARM: dts: BCM5301X: Specify serial console parameters

[Jon Mason]

On Tue, Mar 14, 2017 at 8:32 AM, Rafa? Mi?ecki <zajec5@gmail.com> wrote:
> On 03/14/2017 01:26 PM, Andrew Lunn wrote:
>>
>> On Tue, Mar 14, 2017 at 08:58:29AM +0100, Rafa?? Mi??ecki wrote:
>>>
>>> From: Rafa?? Mi??ecki <rafal@milecki.pl>
>>>
>>> This adds baud rate, parity & number of data bits. It's required to get
>>> serial working correctly.
>>>
>>> Signed-off-by: Rafa?? Mi??ecki <rafal@milecki.pl>
>>> ---
>>>  arch/arm/boot/dts/bcm5301x.dtsi | 6 +++++-
>>>  1 file changed, 5 insertions(+), 1 deletion(-)
>>>
>>> diff --git a/arch/arm/boot/dts/bcm5301x.dtsi
>>> b/arch/arm/boot/dts/bcm5301x.dtsi
>>> index 8fd1ef9f0c2d..468107166a6f 100644
>>> --- a/arch/arm/boot/dts/bcm5301x.dtsi
>>> +++ b/arch/arm/boot/dts/bcm5301x.dtsi
>>> @@ -18,8 +18,12 @@
>>>  / {
>>>         interrupt-parent = <&gic>;
>>>
>>> +       aliases {
>>> +               serial0 = &uart0;
>>> +       };
>>> +
>>>         chosen {
>>> -               stdout-path = &uart0;
>>> +               stdout-path = "serial0:115200n8";
>>>         };
>>
>>
>> Hi Rafal
>>
>> The alias is fine. But putting the stdout-path here is unusual. Which
>> serial port is used for console is board specific, where as
>> bcm5301x.dtsi is very generic, it describes the SoC, not a board.  If
>> you look at other .dtsi files, those that specify stdout-path contain
>> properties which are common to a range of similar boards.
>
>
> So far I've never seen any board using other uart. Also uart0 is disabled by
> default and we enable it per board family (BCM4708 / BCM47081 / BCM4709 /
> BCM47094). I think it's just more practical to have simple DTS that covers
> 99,9% boards by default and handled that margin of devices separately.
>
> We already got a lot of duplicated code for enabling uart0, see:
> https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=7b790d3b2943bf8e7e7bafe184008bd6451fe0bd
>
> Jon Mason from Broadcom who knows this hardware and designs very well
> confirmed
> it's a sane/safe assumption.


It should work for all the boards.  The question is whether it should
be in the DTSI or DTS file.  This code replicates code I have in
arch/arm/boot/dts/bcm953012k.dts
So, either it should be removed or we should change all of the other
DTS files to have this entry.  My understanding is that the latter
approach is the acceptable one (which matches Andrew's comment), but I
can make the other changes if necessary.

Thanks,
Jon

Re: [PATCH 1/2] ARM: dts: BCM5301X: Specify serial console parameters

[Jon Mason]

On Tue, Mar 14, 2017 at 8:32 AM, Rafał Miłecki <zajec5@gmail.com> wrote:
> On 03/14/2017 01:26 PM, Andrew Lunn wrote:
>>
>> On Tue, Mar 14, 2017 at 08:58:29AM +0100, Rafa?? Mi??ecki wrote:
>>>
>>> From: Rafa?? Mi??ecki <rafal@milecki.pl>
>>>
>>> This adds baud rate, parity & number of data bits. It's required to get
>>> serial working correctly.
>>>
>>> Signed-off-by: Rafa?? Mi??ecki <rafal@milecki.pl>
>>> ---
>>>  arch/arm/boot/dts/bcm5301x.dtsi | 6 +++++-
>>>  1 file changed, 5 insertions(+), 1 deletion(-)
>>>
>>> diff --git a/arch/arm/boot/dts/bcm5301x.dtsi
>>> b/arch/arm/boot/dts/bcm5301x.dtsi
>>> index 8fd1ef9f0c2d..468107166a6f 100644
>>> --- a/arch/arm/boot/dts/bcm5301x.dtsi
>>> +++ b/arch/arm/boot/dts/bcm5301x.dtsi
>>> @@ -18,8 +18,12 @@
>>>  / {
>>>         interrupt-parent = <&gic>;
>>>
>>> +       aliases {
>>> +               serial0 = &uart0;
>>> +       };
>>> +
>>>         chosen {
>>> -               stdout-path = &uart0;
>>> +               stdout-path = "serial0:115200n8";
>>>         };
>>
>>
>> Hi Rafal
>>
>> The alias is fine. But putting the stdout-path here is unusual. Which
>> serial port is used for console is board specific, where as
>> bcm5301x.dtsi is very generic, it describes the SoC, not a board.  If
>> you look at other .dtsi files, those that specify stdout-path contain
>> properties which are common to a range of similar boards.
>
>
> So far I've never seen any board using other uart. Also uart0 is disabled by
> default and we enable it per board family (BCM4708 / BCM47081 / BCM4709 /
> BCM47094). I think it's just more practical to have simple DTS that covers
> 99,9% boards by default and handled that margin of devices separately.
>
> We already got a lot of duplicated code for enabling uart0, see:
> https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=7b790d3b2943bf8e7e7bafe184008bd6451fe0bd
>
> Jon Mason from Broadcom who knows this hardware and designs very well
> confirmed
> it's a sane/safe assumption.


It should work for all the boards.  The question is whether it should
be in the DTSI or DTS file.  This code replicates code I have in
arch/arm/boot/dts/bcm953012k.dts
So, either it should be removed or we should change all of the other
DTS files to have this entry.  My understanding is that the latter
approach is the acceptable one (which matches Andrew's comment), but I
can make the other changes if necessary.

Thanks,
Jon

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 1/2] ARM: dts: BCM5301X: Specify serial console parameters

[Scott Branden]

On 17-03-14 07:53 AM, Jon Mason wrote:
> On Tue, Mar 14, 2017 at 8:32 AM, Rafa? Mi?ecki <zajec5@gmail.com> wrote:
>> On 03/14/2017 01:26 PM, Andrew Lunn wrote:
>>>
>>> On Tue, Mar 14, 2017 at 08:58:29AM +0100, Rafa?? Mi??ecki wrote:
>>>>
>>>> From: Rafa?? Mi??ecki <rafal@milecki.pl>
>>>>
>>>> This adds baud rate, parity & number of data bits. It's required to get
>>>> serial working correctly.
>>>>
>>>> Signed-off-by: Rafa?? Mi??ecki <rafal@milecki.pl>
>>>> ---
>>>>  arch/arm/boot/dts/bcm5301x.dtsi | 6 +++++-
>>>>  1 file changed, 5 insertions(+), 1 deletion(-)
>>>>
>>>> diff --git a/arch/arm/boot/dts/bcm5301x.dtsi
>>>> b/arch/arm/boot/dts/bcm5301x.dtsi
>>>> index 8fd1ef9f0c2d..468107166a6f 100644
>>>> --- a/arch/arm/boot/dts/bcm5301x.dtsi
>>>> +++ b/arch/arm/boot/dts/bcm5301x.dtsi
>>>> @@ -18,8 +18,12 @@
>>>>  / {
>>>>         interrupt-parent = <&gic>;
>>>>
>>>> +       aliases {
>>>> +               serial0 = &uart0;
>>>> +       };
>>>> +
>>>>         chosen {
>>>> -               stdout-path = &uart0;
>>>> +               stdout-path = "serial0:115200n8";
>>>>         };
>>>
>>>
>>> Hi Rafal
>>>
>>> The alias is fine. But putting the stdout-path here is unusual. Which
>>> serial port is used for console is board specific, where as
>>> bcm5301x.dtsi is very generic, it describes the SoC, not a board.  If
>>> you look at other .dtsi files, those that specify stdout-path contain
>>> properties which are common to a range of similar boards.
>>
>>
>> So far I've never seen any board using other uart. Also uart0 is disabled by
>> default and we enable it per board family (BCM4708 / BCM47081 / BCM4709 /
>> BCM47094). I think it's just more practical to have simple DTS that covers
>> 99,9% boards by default and handled that margin of devices separately.
>>
>> We already got a lot of duplicated code for enabling uart0, see:
>> https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=7b790d3b2943bf8e7e7bafe184008bd6451fe0bd
>>
>> Jon Mason from Broadcom who knows this hardware and designs very well
>> confirmed
>> it's a sane/safe assumption.
>
>
> It should work for all the boards.  The question is whether it should
> be in the DTSI or DTS file.  This code replicates code I have in
> arch/arm/boot/dts/bcm953012k.dts
> So, either it should be removed or we should change all of the other
> DTS files to have this entry.  My understanding is that the latter
> approach is the acceptable one (which matches Andrew's comment), but I
> can make the other changes if necessary.
dtsi file is fine to handle 99% of the use cases and not duplicate the 
entry.  This is what we do for newer SoCs (such as Cygnus) where the 
console will always be a particular UART (as the BootROM already uses a 
certain UART the boards are designed to use that UART as the console 
always).  For bcm953012 a similar situation exists as a common 
bootloader is used across boards.  So, the uart used as the terminal 
will always be the same.

I don't see a good reason for duplicating the code in every dts file.

Acked-by: Scott Branden <scott.branden@broadcom.com>
>
> Thanks,
> Jon
>

Re: [PATCH 1/2] ARM: dts: BCM5301X: Specify serial console parameters

[Scott Branden]

On 17-03-14 07:53 AM, Jon Mason wrote:
> On Tue, Mar 14, 2017 at 8:32 AM, Rafał Miłecki <zajec5-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> wrote:
>> On 03/14/2017 01:26 PM, Andrew Lunn wrote:
>>>
>>> On Tue, Mar 14, 2017 at 08:58:29AM +0100, Rafa?? Mi??ecki wrote:
>>>>
>>>> From: Rafa?? Mi??ecki <rafal-g1n6cQUeyibVItvQsEIGlw@public.gmane.org>
>>>>
>>>> This adds baud rate, parity & number of data bits. It's required to get
>>>> serial working correctly.
>>>>
>>>> Signed-off-by: Rafa?? Mi??ecki <rafal-g1n6cQUeyibVItvQsEIGlw@public.gmane.org>
>>>> ---
>>>>  arch/arm/boot/dts/bcm5301x.dtsi | 6 +++++-
>>>>  1 file changed, 5 insertions(+), 1 deletion(-)
>>>>
>>>> diff --git a/arch/arm/boot/dts/bcm5301x.dtsi
>>>> b/arch/arm/boot/dts/bcm5301x.dtsi
>>>> index 8fd1ef9f0c2d..468107166a6f 100644
>>>> --- a/arch/arm/boot/dts/bcm5301x.dtsi
>>>> +++ b/arch/arm/boot/dts/bcm5301x.dtsi
>>>> @@ -18,8 +18,12 @@
>>>>  / {
>>>>         interrupt-parent = <&gic>;
>>>>
>>>> +       aliases {
>>>> +               serial0 = &uart0;
>>>> +       };
>>>> +
>>>>         chosen {
>>>> -               stdout-path = &uart0;
>>>> +               stdout-path = "serial0:115200n8";
>>>>         };
>>>
>>>
>>> Hi Rafal
>>>
>>> The alias is fine. But putting the stdout-path here is unusual. Which
>>> serial port is used for console is board specific, where as
>>> bcm5301x.dtsi is very generic, it describes the SoC, not a board.  If
>>> you look at other .dtsi files, those that specify stdout-path contain
>>> properties which are common to a range of similar boards.
>>
>>
>> So far I've never seen any board using other uart. Also uart0 is disabled by
>> default and we enable it per board family (BCM4708 / BCM47081 / BCM4709 /
>> BCM47094). I think it's just more practical to have simple DTS that covers
>> 99,9% boards by default and handled that margin of devices separately.
>>
>> We already got a lot of duplicated code for enabling uart0, see:
>> https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=7b790d3b2943bf8e7e7bafe184008bd6451fe0bd
>>
>> Jon Mason from Broadcom who knows this hardware and designs very well
>> confirmed
>> it's a sane/safe assumption.
>
>
> It should work for all the boards.  The question is whether it should
> be in the DTSI or DTS file.  This code replicates code I have in
> arch/arm/boot/dts/bcm953012k.dts
> So, either it should be removed or we should change all of the other
> DTS files to have this entry.  My understanding is that the latter
> approach is the acceptable one (which matches Andrew's comment), but I
> can make the other changes if necessary.
dtsi file is fine to handle 99% of the use cases and not duplicate the 
entry.  This is what we do for newer SoCs (such as Cygnus) where the 
console will always be a particular UART (as the BootROM already uses a 
certain UART the boards are designed to use that UART as the console 
always).  For bcm953012 a similar situation exists as a common 
bootloader is used across boards.  So, the uart used as the terminal 
will always be the same.

I don't see a good reason for duplicating the code in every dts file.

Acked-by: Scott Branden <scott.branden-dY08KVG/lbpWk0Htik3J/w@public.gmane.org>
>
> Thanks,
> Jon
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 1/2] ARM: dts: BCM5301X: Specify serial console parameters

[Jon Mason]

On Tue, Mar 14, 2017 at 4:44 PM, Scott Branden
<scott.branden@broadcom.com> wrote:
>
>
> On 17-03-14 07:53 AM, Jon Mason wrote:
>>
>> On Tue, Mar 14, 2017 at 8:32 AM, Rafa? Mi?ecki <zajec5@gmail.com> wrote:
>>>
>>> On 03/14/2017 01:26 PM, Andrew Lunn wrote:
>>>>
>>>>
>>>> On Tue, Mar 14, 2017 at 08:58:29AM +0100, Rafa?? Mi??ecki wrote:
>>>>>
>>>>>
>>>>> From: Rafa?? Mi??ecki <rafal@milecki.pl>
>>>>>
>>>>> This adds baud rate, parity & number of data bits. It's required to get
>>>>> serial working correctly.
>>>>>
>>>>> Signed-off-by: Rafa?? Mi??ecki <rafal@milecki.pl>
>>>>> ---
>>>>>  arch/arm/boot/dts/bcm5301x.dtsi | 6 +++++-
>>>>>  1 file changed, 5 insertions(+), 1 deletion(-)
>>>>>
>>>>> diff --git a/arch/arm/boot/dts/bcm5301x.dtsi
>>>>> b/arch/arm/boot/dts/bcm5301x.dtsi
>>>>> index 8fd1ef9f0c2d..468107166a6f 100644
>>>>> --- a/arch/arm/boot/dts/bcm5301x.dtsi
>>>>> +++ b/arch/arm/boot/dts/bcm5301x.dtsi
>>>>> @@ -18,8 +18,12 @@
>>>>>  / {
>>>>>         interrupt-parent = <&gic>;
>>>>>
>>>>> +       aliases {
>>>>> +               serial0 = &uart0;
>>>>> +       };
>>>>> +
>>>>>         chosen {
>>>>> -               stdout-path = &uart0;
>>>>> +               stdout-path = "serial0:115200n8";
>>>>>         };
>>>>
>>>>
>>>>
>>>> Hi Rafal
>>>>
>>>> The alias is fine. But putting the stdout-path here is unusual. Which
>>>> serial port is used for console is board specific, where as
>>>> bcm5301x.dtsi is very generic, it describes the SoC, not a board.  If
>>>> you look at other .dtsi files, those that specify stdout-path contain
>>>> properties which are common to a range of similar boards.
>>>
>>>
>>>
>>> So far I've never seen any board using other uart. Also uart0 is disabled
>>> by
>>> default and we enable it per board family (BCM4708 / BCM47081 / BCM4709 /
>>> BCM47094). I think it's just more practical to have simple DTS that
>>> covers
>>> 99,9% boards by default and handled that margin of devices separately.
>>>
>>> We already got a lot of duplicated code for enabling uart0, see:
>>>
>>> https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=7b790d3b2943bf8e7e7bafe184008bd6451fe0bd
>>>
>>> Jon Mason from Broadcom who knows this hardware and designs very well
>>> confirmed
>>> it's a sane/safe assumption.
>>
>>
>>
>> It should work for all the boards.  The question is whether it should
>> be in the DTSI or DTS file.  This code replicates code I have in
>> arch/arm/boot/dts/bcm953012k.dts
>> So, either it should be removed or we should change all of the other
>> DTS files to have this entry.  My understanding is that the latter
>> approach is the acceptable one (which matches Andrew's comment), but I
>> can make the other changes if necessary.
>
> dtsi file is fine to handle 99% of the use cases and not duplicate the
> entry.  This is what we do for newer SoCs (such as Cygnus) where the console
> will always be a particular UART (as the BootROM already uses a certain UART
> the boards are designed to use that UART as the console always).  For
> bcm953012 a similar situation exists as a common bootloader is used across
> boards.  So, the uart used as the terminal will always be the same.

Unfortunately, there is not a common bootloader.  CFE is used for the
4708/9 boards, and u-boot is used for the 5301x boards.

Thanks,
Jon

> I don't see a good reason for duplicating the code in every dts file.
>
> Acked-by: Scott Branden <scott.branden@broadcom.com>
>>
>>
>> Thanks,
>> Jon
>>
>

Re: [PATCH 1/2] ARM: dts: BCM5301X: Specify serial console parameters

[Jon Mason]

On Tue, Mar 14, 2017 at 4:44 PM, Scott Branden
<scott.branden-dY08KVG/lbpWk0Htik3J/w@public.gmane.org> wrote:
>
>
> On 17-03-14 07:53 AM, Jon Mason wrote:
>>
>> On Tue, Mar 14, 2017 at 8:32 AM, Rafał Miłecki <zajec5@gmail.com> wrote:
>>>
>>> On 03/14/2017 01:26 PM, Andrew Lunn wrote:
>>>>
>>>>
>>>> On Tue, Mar 14, 2017 at 08:58:29AM +0100, Rafa?? Mi??ecki wrote:
>>>>>
>>>>>
>>>>> From: Rafa?? Mi??ecki <rafal-g1n6cQUeyibVItvQsEIGlw@public.gmane.org>
>>>>>
>>>>> This adds baud rate, parity & number of data bits. It's required to get
>>>>> serial working correctly.
>>>>>
>>>>> Signed-off-by: Rafa?? Mi??ecki <rafal-g1n6cQUeyibVItvQsEIGlw@public.gmane.org>
>>>>> ---
>>>>>  arch/arm/boot/dts/bcm5301x.dtsi | 6 +++++-
>>>>>  1 file changed, 5 insertions(+), 1 deletion(-)
>>>>>
>>>>> diff --git a/arch/arm/boot/dts/bcm5301x.dtsi
>>>>> b/arch/arm/boot/dts/bcm5301x.dtsi
>>>>> index 8fd1ef9f0c2d..468107166a6f 100644
>>>>> --- a/arch/arm/boot/dts/bcm5301x.dtsi
>>>>> +++ b/arch/arm/boot/dts/bcm5301x.dtsi
>>>>> @@ -18,8 +18,12 @@
>>>>>  / {
>>>>>         interrupt-parent = <&gic>;
>>>>>
>>>>> +       aliases {
>>>>> +               serial0 = &uart0;
>>>>> +       };
>>>>> +
>>>>>         chosen {
>>>>> -               stdout-path = &uart0;
>>>>> +               stdout-path = "serial0:115200n8";
>>>>>         };
>>>>
>>>>
>>>>
>>>> Hi Rafal
>>>>
>>>> The alias is fine. But putting the stdout-path here is unusual. Which
>>>> serial port is used for console is board specific, where as
>>>> bcm5301x.dtsi is very generic, it describes the SoC, not a board.  If
>>>> you look at other .dtsi files, those that specify stdout-path contain
>>>> properties which are common to a range of similar boards.
>>>
>>>
>>>
>>> So far I've never seen any board using other uart. Also uart0 is disabled
>>> by
>>> default and we enable it per board family (BCM4708 / BCM47081 / BCM4709 /
>>> BCM47094). I think it's just more practical to have simple DTS that
>>> covers
>>> 99,9% boards by default and handled that margin of devices separately.
>>>
>>> We already got a lot of duplicated code for enabling uart0, see:
>>>
>>> https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=7b790d3b2943bf8e7e7bafe184008bd6451fe0bd
>>>
>>> Jon Mason from Broadcom who knows this hardware and designs very well
>>> confirmed
>>> it's a sane/safe assumption.
>>
>>
>>
>> It should work for all the boards.  The question is whether it should
>> be in the DTSI or DTS file.  This code replicates code I have in
>> arch/arm/boot/dts/bcm953012k.dts
>> So, either it should be removed or we should change all of the other
>> DTS files to have this entry.  My understanding is that the latter
>> approach is the acceptable one (which matches Andrew's comment), but I
>> can make the other changes if necessary.
>
> dtsi file is fine to handle 99% of the use cases and not duplicate the
> entry.  This is what we do for newer SoCs (such as Cygnus) where the console
> will always be a particular UART (as the BootROM already uses a certain UART
> the boards are designed to use that UART as the console always).  For
> bcm953012 a similar situation exists as a common bootloader is used across
> boards.  So, the uart used as the terminal will always be the same.

Unfortunately, there is not a common bootloader.  CFE is used for the
4708/9 boards, and u-boot is used for the 5301x boards.

Thanks,
Jon

> I don't see a good reason for duplicating the code in every dts file.
>
> Acked-by: Scott Branden <scott.branden-dY08KVG/lbpWk0Htik3J/w@public.gmane.org>
>>
>>
>> Thanks,
>> Jon
>>
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 1/2] ARM: dts: BCM5301X: Specify serial console parameters

[Scott Branden]

On 17-03-14 02:18 PM, Jon Mason wrote:
> On Tue, Mar 14, 2017 at 4:44 PM, Scott Branden
> <scott.branden@broadcom.com> wrote:
>>
>>
>> On 17-03-14 07:53 AM, Jon Mason wrote:
>>>
>>> On Tue, Mar 14, 2017 at 8:32 AM, Rafa? Mi?ecki <zajec5@gmail.com> wrote:
>>>>
>>>> On 03/14/2017 01:26 PM, Andrew Lunn wrote:
>>>>>
>>>>>
>>>>> On Tue, Mar 14, 2017 at 08:58:29AM +0100, Rafa?? Mi??ecki wrote:
>>>>>>
>>>>>>
>>>>>> From: Rafa?? Mi??ecki <rafal@milecki.pl>
>>>>>>
>>>>>> This adds baud rate, parity & number of data bits. It's required to get
>>>>>> serial working correctly.
>>>>>>
>>>>>> Signed-off-by: Rafa?? Mi??ecki <rafal@milecki.pl>
>>>>>> ---
>>>>>>  arch/arm/boot/dts/bcm5301x.dtsi | 6 +++++-
>>>>>>  1 file changed, 5 insertions(+), 1 deletion(-)
>>>>>>
>>>>>> diff --git a/arch/arm/boot/dts/bcm5301x.dtsi
>>>>>> b/arch/arm/boot/dts/bcm5301x.dtsi
>>>>>> index 8fd1ef9f0c2d..468107166a6f 100644
>>>>>> --- a/arch/arm/boot/dts/bcm5301x.dtsi
>>>>>> +++ b/arch/arm/boot/dts/bcm5301x.dtsi
>>>>>> @@ -18,8 +18,12 @@
>>>>>>  / {
>>>>>>         interrupt-parent = <&gic>;
>>>>>>
>>>>>> +       aliases {
>>>>>> +               serial0 = &uart0;
>>>>>> +       };
>>>>>> +
>>>>>>         chosen {
>>>>>> -               stdout-path = &uart0;
>>>>>> +               stdout-path = "serial0:115200n8";
>>>>>>         };
>>>>>
>>>>>
>>>>>
>>>>> Hi Rafal
>>>>>
>>>>> The alias is fine. But putting the stdout-path here is unusual. Which
>>>>> serial port is used for console is board specific, where as
>>>>> bcm5301x.dtsi is very generic, it describes the SoC, not a board.  If
>>>>> you look at other .dtsi files, those that specify stdout-path contain
>>>>> properties which are common to a range of similar boards.
>>>>
>>>>
>>>>
>>>> So far I've never seen any board using other uart. Also uart0 is disabled
>>>> by
>>>> default and we enable it per board family (BCM4708 / BCM47081 / BCM4709 /
>>>> BCM47094). I think it's just more practical to have simple DTS that
>>>> covers
>>>> 99,9% boards by default and handled that margin of devices separately.
>>>>
>>>> We already got a lot of duplicated code for enabling uart0, see:
>>>>
>>>> https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=7b790d3b2943bf8e7e7bafe184008bd6451fe0bd
>>>>
>>>> Jon Mason from Broadcom who knows this hardware and designs very well
>>>> confirmed
>>>> it's a sane/safe assumption.
>>>
>>>
>>>
>>> It should work for all the boards.  The question is whether it should
>>> be in the DTSI or DTS file.  This code replicates code I have in
>>> arch/arm/boot/dts/bcm953012k.dts
>>> So, either it should be removed or we should change all of the other
>>> DTS files to have this entry.  My understanding is that the latter
>>> approach is the acceptable one (which matches Andrew's comment), but I
>>> can make the other changes if necessary.
>>
>> dtsi file is fine to handle 99% of the use cases and not duplicate the
>> entry.  This is what we do for newer SoCs (such as Cygnus) where the console
>> will always be a particular UART (as the BootROM already uses a certain UART
>> the boards are designed to use that UART as the console always).  For
>> bcm953012 a similar situation exists as a common bootloader is used across
>> boards.  So, the uart used as the terminal will always be the same.
>
> Unfortunately, there is not a common bootloader.  CFE is used for the
> 4708/9 boards, and u-boot is used for the 5301x boards.
OK, little different situation not having a boot rom with console output 
enforcing all designs to use the same UART.
Do both of the bootloaders happen to use the same UART and all the 
boards are designed to use the same UART?
>
> Thanks,
> Jon
>
>> I don't see a good reason for duplicating the code in every dts file.
>>
>> Acked-by: Scott Branden <scott.branden@broadcom.com>
>>>
>>>
>>> Thanks,
>>> Jon
>>>
>>

Re: [PATCH 1/2] ARM: dts: BCM5301X: Specify serial console parameters

[Scott Branden]

On 17-03-14 02:18 PM, Jon Mason wrote:
> On Tue, Mar 14, 2017 at 4:44 PM, Scott Branden
> <scott.branden-dY08KVG/lbpWk0Htik3J/w@public.gmane.org> wrote:
>>
>>
>> On 17-03-14 07:53 AM, Jon Mason wrote:
>>>
>>> On Tue, Mar 14, 2017 at 8:32 AM, Rafał Miłecki <zajec5-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> wrote:
>>>>
>>>> On 03/14/2017 01:26 PM, Andrew Lunn wrote:
>>>>>
>>>>>
>>>>> On Tue, Mar 14, 2017 at 08:58:29AM +0100, Rafa?? Mi??ecki wrote:
>>>>>>
>>>>>>
>>>>>> From: Rafa?? Mi??ecki <rafal-g1n6cQUeyibVItvQsEIGlw@public.gmane.org>
>>>>>>
>>>>>> This adds baud rate, parity & number of data bits. It's required to get
>>>>>> serial working correctly.
>>>>>>
>>>>>> Signed-off-by: Rafa?? Mi??ecki <rafal-g1n6cQUeyibVItvQsEIGlw@public.gmane.org>
>>>>>> ---
>>>>>>  arch/arm/boot/dts/bcm5301x.dtsi | 6 +++++-
>>>>>>  1 file changed, 5 insertions(+), 1 deletion(-)
>>>>>>
>>>>>> diff --git a/arch/arm/boot/dts/bcm5301x.dtsi
>>>>>> b/arch/arm/boot/dts/bcm5301x.dtsi
>>>>>> index 8fd1ef9f0c2d..468107166a6f 100644
>>>>>> --- a/arch/arm/boot/dts/bcm5301x.dtsi
>>>>>> +++ b/arch/arm/boot/dts/bcm5301x.dtsi
>>>>>> @@ -18,8 +18,12 @@
>>>>>>  / {
>>>>>>         interrupt-parent = <&gic>;
>>>>>>
>>>>>> +       aliases {
>>>>>> +               serial0 = &uart0;
>>>>>> +       };
>>>>>> +
>>>>>>         chosen {
>>>>>> -               stdout-path = &uart0;
>>>>>> +               stdout-path = "serial0:115200n8";
>>>>>>         };
>>>>>
>>>>>
>>>>>
>>>>> Hi Rafal
>>>>>
>>>>> The alias is fine. But putting the stdout-path here is unusual. Which
>>>>> serial port is used for console is board specific, where as
>>>>> bcm5301x.dtsi is very generic, it describes the SoC, not a board.  If
>>>>> you look at other .dtsi files, those that specify stdout-path contain
>>>>> properties which are common to a range of similar boards.
>>>>
>>>>
>>>>
>>>> So far I've never seen any board using other uart. Also uart0 is disabled
>>>> by
>>>> default and we enable it per board family (BCM4708 / BCM47081 / BCM4709 /
>>>> BCM47094). I think it's just more practical to have simple DTS that
>>>> covers
>>>> 99,9% boards by default and handled that margin of devices separately.
>>>>
>>>> We already got a lot of duplicated code for enabling uart0, see:
>>>>
>>>> https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=7b790d3b2943bf8e7e7bafe184008bd6451fe0bd
>>>>
>>>> Jon Mason from Broadcom who knows this hardware and designs very well
>>>> confirmed
>>>> it's a sane/safe assumption.
>>>
>>>
>>>
>>> It should work for all the boards.  The question is whether it should
>>> be in the DTSI or DTS file.  This code replicates code I have in
>>> arch/arm/boot/dts/bcm953012k.dts
>>> So, either it should be removed or we should change all of the other
>>> DTS files to have this entry.  My understanding is that the latter
>>> approach is the acceptable one (which matches Andrew's comment), but I
>>> can make the other changes if necessary.
>>
>> dtsi file is fine to handle 99% of the use cases and not duplicate the
>> entry.  This is what we do for newer SoCs (such as Cygnus) where the console
>> will always be a particular UART (as the BootROM already uses a certain UART
>> the boards are designed to use that UART as the console always).  For
>> bcm953012 a similar situation exists as a common bootloader is used across
>> boards.  So, the uart used as the terminal will always be the same.
>
> Unfortunately, there is not a common bootloader.  CFE is used for the
> 4708/9 boards, and u-boot is used for the 5301x boards.
OK, little different situation not having a boot rom with console output 
enforcing all designs to use the same UART.
Do both of the bootloaders happen to use the same UART and all the 
boards are designed to use the same UART?
>
> Thanks,
> Jon
>
>> I don't see a good reason for duplicating the code in every dts file.
>>
>> Acked-by: Scott Branden <scott.branden-dY08KVG/lbpWk0Htik3J/w@public.gmane.org>
>>>
>>>
>>> Thanks,
>>> Jon
>>>
>>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 1/2] ARM: dts: BCM5301X: Specify serial console parameters

[Andrew Lunn]

> >Unfortunately, there is not a common bootloader.  CFE is used for the
> >4708/9 boards, and u-boot is used for the 5301x boards.
> OK, little different situation not having a boot rom with console
> output enforcing all designs to use the same UART.
> Do both of the bootloaders happen to use the same UART and all the
> boards are designed to use the same UART?

You need to be a little bit careful here. Some vendor could use a
different UART in there design, use some other bootloader,
etc. Somebody in the community might want to throw out uboot and use
barebox etc....

Device tree does allow .dtsi properties to be over written, so it is
not an issue in practice.

    Andrew

Re: [PATCH 1/2] ARM: dts: BCM5301X: Specify serial console parameters

[Andrew Lunn]

> >Unfortunately, there is not a common bootloader.  CFE is used for the
> >4708/9 boards, and u-boot is used for the 5301x boards.
> OK, little different situation not having a boot rom with console
> output enforcing all designs to use the same UART.
> Do both of the bootloaders happen to use the same UART and all the
> boards are designed to use the same UART?

You need to be a little bit careful here. Some vendor could use a
different UART in there design, use some other bootloader,
etc. Somebody in the community might want to throw out uboot and use
barebox etc....

Device tree does allow .dtsi properties to be over written, so it is
not an issue in practice.

    Andrew
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH V2 1/2] ARM: dts: BCM5301X: Specify serial console params in dtsi files

[Rafał Miłecki]

From: Rafa? Mi?ecki <rafal@milecki.pl>

So far every Northstar device we have seen was using the same serial
console params (115200n8). It probably make the most sense to put it in
some proper dtsi files instead of repeating over and over for every
single device. As different boards may use different bootloaders it
seems the safest idea is to use board specific dtsi files.

Just in case some vendor decides to use different UART (parameters) this
can be always easily overwritten.

Signed-off-by: Rafa? Mi?ecki <rafal@milecki.pl>
---
V2: Use board dtsi files, update existing bcm9*dts files, update commit message.
---
 arch/arm/boot/dts/bcm4708.dtsi    | 8 ++++++++
 arch/arm/boot/dts/bcm47081.dtsi   | 8 ++++++++
 arch/arm/boot/dts/bcm5301x.dtsi   | 4 ----
 arch/arm/boot/dts/bcm94708.dts    | 8 --------
 arch/arm/boot/dts/bcm94709.dts    | 8 --------
 arch/arm/boot/dts/bcm953012er.dts | 8 --------
 arch/arm/boot/dts/bcm953012hr.dts | 8 --------
 arch/arm/boot/dts/bcm953012k.dts  | 4 ----
 8 files changed, 16 insertions(+), 40 deletions(-)

diff --git a/arch/arm/boot/dts/bcm4708.dtsi b/arch/arm/boot/dts/bcm4708.dtsi
index d0eec099f1f8..1a19e97a987d 100644
--- a/arch/arm/boot/dts/bcm4708.dtsi
+++ b/arch/arm/boot/dts/bcm4708.dtsi
@@ -12,6 +12,14 @@
 / {
 	compatible = "brcm,bcm4708";
 
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
 	cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;
diff --git a/arch/arm/boot/dts/bcm47081.dtsi b/arch/arm/boot/dts/bcm47081.dtsi
index 7bcd536198fc..9829d044aaf4 100644
--- a/arch/arm/boot/dts/bcm47081.dtsi
+++ b/arch/arm/boot/dts/bcm47081.dtsi
@@ -22,6 +22,14 @@
 / {
 	compatible = "brcm,bcm47081";
 
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
 	cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;
diff --git a/arch/arm/boot/dts/bcm5301x.dtsi b/arch/arm/boot/dts/bcm5301x.dtsi
index 8fd1ef9f0c2d..65dc67e86ae1 100644
--- a/arch/arm/boot/dts/bcm5301x.dtsi
+++ b/arch/arm/boot/dts/bcm5301x.dtsi
@@ -18,10 +18,6 @@
 / {
 	interrupt-parent = <&gic>;
 
-	chosen {
-		stdout-path = &uart0;
-	};
-
 	chipcommonA {
 		compatible = "simple-bus";
 		ranges = <0x00000000 0x18000000 0x00001000>;
diff --git a/arch/arm/boot/dts/bcm94708.dts b/arch/arm/boot/dts/bcm94708.dts
index 42855a7c1bfa..2e08c895f281 100644
--- a/arch/arm/boot/dts/bcm94708.dts
+++ b/arch/arm/boot/dts/bcm94708.dts
@@ -38,14 +38,6 @@
 	model = "NorthStar SVK (BCM94708)";
 	compatible = "brcm,bcm94708", "brcm,bcm4708";
 
-	aliases {
-		serial0 = &uart0;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
 	memory {
 		reg = <0x00000000 0x08000000>;
 	};
diff --git a/arch/arm/boot/dts/bcm94709.dts b/arch/arm/boot/dts/bcm94709.dts
index 95e8be65f2f1..c37616c67edc 100644
--- a/arch/arm/boot/dts/bcm94709.dts
+++ b/arch/arm/boot/dts/bcm94709.dts
@@ -38,14 +38,6 @@
 	model = "NorthStar SVK (BCM94709)";
 	compatible = "brcm,bcm94709", "brcm,bcm4709", "brcm,bcm4708";
 
-	aliases {
-		serial0 = &uart0;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
 	memory {
 		reg = <0x00000000 0x08000000>;
 	};
diff --git a/arch/arm/boot/dts/bcm953012er.dts b/arch/arm/boot/dts/bcm953012er.dts
index decd86bae901..40e694bfe5ca 100644
--- a/arch/arm/boot/dts/bcm953012er.dts
+++ b/arch/arm/boot/dts/bcm953012er.dts
@@ -39,14 +39,6 @@
 	model = "NorthStar Enterprise Router (BCM953012ER)";
 	compatible = "brcm,bcm953012er", "brcm,brcm53012", "brcm,bcm4708";
 
-	aliases {
-		serial0 = &uart0;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
 	memory {
 		reg = <0x00000000 0x8000000>;
 	};
diff --git a/arch/arm/boot/dts/bcm953012hr.dts b/arch/arm/boot/dts/bcm953012hr.dts
index 85f9b0b872ac..5be4225324a3 100644
--- a/arch/arm/boot/dts/bcm953012hr.dts
+++ b/arch/arm/boot/dts/bcm953012hr.dts
@@ -39,14 +39,6 @@
 	model = "NorthStar HR (BCM953012HR)";
 	compatible = "brcm,bcm953012hr", "brcm,brcm53012", "brcm,bcm4708";
 
-	aliases {
-		serial0 = &uart0;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
 	memory at 80000000 {
 		reg = <0x80000000 0x10000000>;
 	};
diff --git a/arch/arm/boot/dts/bcm953012k.dts b/arch/arm/boot/dts/bcm953012k.dts
index a00c4e1dfb4c..fbc6219e977a 100644
--- a/arch/arm/boot/dts/bcm953012k.dts
+++ b/arch/arm/boot/dts/bcm953012k.dts
@@ -43,10 +43,6 @@
 		serial1 = &uart1;
 	};
 
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
 	memory {
 		reg = <0x00000000 0x10000000>;
 	};
-- 
2.11.0

[PATCH V2 1/2] ARM: dts: BCM5301X: Specify serial console params in dtsi files

[Rafał Miłecki]

From: Rafał Miłecki <rafal-g1n6cQUeyibVItvQsEIGlw@public.gmane.org>

So far every Northstar device we have seen was using the same serial
console params (115200n8). It probably make the most sense to put it in
some proper dtsi files instead of repeating over and over for every
single device. As different boards may use different bootloaders it
seems the safest idea is to use board specific dtsi files.

Just in case some vendor decides to use different UART (parameters) this
can be always easily overwritten.

Signed-off-by: Rafał Miłecki <rafal-g1n6cQUeyibVItvQsEIGlw@public.gmane.org>
---
V2: Use board dtsi files, update existing bcm9*dts files, update commit message.
---
 arch/arm/boot/dts/bcm4708.dtsi    | 8 ++++++++
 arch/arm/boot/dts/bcm47081.dtsi   | 8 ++++++++
 arch/arm/boot/dts/bcm5301x.dtsi   | 4 ----
 arch/arm/boot/dts/bcm94708.dts    | 8 --------
 arch/arm/boot/dts/bcm94709.dts    | 8 --------
 arch/arm/boot/dts/bcm953012er.dts | 8 --------
 arch/arm/boot/dts/bcm953012hr.dts | 8 --------
 arch/arm/boot/dts/bcm953012k.dts  | 4 ----
 8 files changed, 16 insertions(+), 40 deletions(-)

diff --git a/arch/arm/boot/dts/bcm4708.dtsi b/arch/arm/boot/dts/bcm4708.dtsi
index d0eec099f1f8..1a19e97a987d 100644
--- a/arch/arm/boot/dts/bcm4708.dtsi
+++ b/arch/arm/boot/dts/bcm4708.dtsi
@@ -12,6 +12,14 @@
 / {
 	compatible = "brcm,bcm4708";
 
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
 	cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;
diff --git a/arch/arm/boot/dts/bcm47081.dtsi b/arch/arm/boot/dts/bcm47081.dtsi
index 7bcd536198fc..9829d044aaf4 100644
--- a/arch/arm/boot/dts/bcm47081.dtsi
+++ b/arch/arm/boot/dts/bcm47081.dtsi
@@ -22,6 +22,14 @@
 / {
 	compatible = "brcm,bcm47081";
 
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
 	cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;
diff --git a/arch/arm/boot/dts/bcm5301x.dtsi b/arch/arm/boot/dts/bcm5301x.dtsi
index 8fd1ef9f0c2d..65dc67e86ae1 100644
--- a/arch/arm/boot/dts/bcm5301x.dtsi
+++ b/arch/arm/boot/dts/bcm5301x.dtsi
@@ -18,10 +18,6 @@
 / {
 	interrupt-parent = <&gic>;
 
-	chosen {
-		stdout-path = &uart0;
-	};
-
 	chipcommonA {
 		compatible = "simple-bus";
 		ranges = <0x00000000 0x18000000 0x00001000>;
diff --git a/arch/arm/boot/dts/bcm94708.dts b/arch/arm/boot/dts/bcm94708.dts
index 42855a7c1bfa..2e08c895f281 100644
--- a/arch/arm/boot/dts/bcm94708.dts
+++ b/arch/arm/boot/dts/bcm94708.dts
@@ -38,14 +38,6 @@
 	model = "NorthStar SVK (BCM94708)";
 	compatible = "brcm,bcm94708", "brcm,bcm4708";
 
-	aliases {
-		serial0 = &uart0;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
 	memory {
 		reg = <0x00000000 0x08000000>;
 	};
diff --git a/arch/arm/boot/dts/bcm94709.dts b/arch/arm/boot/dts/bcm94709.dts
index 95e8be65f2f1..c37616c67edc 100644
--- a/arch/arm/boot/dts/bcm94709.dts
+++ b/arch/arm/boot/dts/bcm94709.dts
@@ -38,14 +38,6 @@
 	model = "NorthStar SVK (BCM94709)";
 	compatible = "brcm,bcm94709", "brcm,bcm4709", "brcm,bcm4708";
 
-	aliases {
-		serial0 = &uart0;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
 	memory {
 		reg = <0x00000000 0x08000000>;
 	};
diff --git a/arch/arm/boot/dts/bcm953012er.dts b/arch/arm/boot/dts/bcm953012er.dts
index decd86bae901..40e694bfe5ca 100644
--- a/arch/arm/boot/dts/bcm953012er.dts
+++ b/arch/arm/boot/dts/bcm953012er.dts
@@ -39,14 +39,6 @@
 	model = "NorthStar Enterprise Router (BCM953012ER)";
 	compatible = "brcm,bcm953012er", "brcm,brcm53012", "brcm,bcm4708";
 
-	aliases {
-		serial0 = &uart0;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
 	memory {
 		reg = <0x00000000 0x8000000>;
 	};
diff --git a/arch/arm/boot/dts/bcm953012hr.dts b/arch/arm/boot/dts/bcm953012hr.dts
index 85f9b0b872ac..5be4225324a3 100644
--- a/arch/arm/boot/dts/bcm953012hr.dts
+++ b/arch/arm/boot/dts/bcm953012hr.dts
@@ -39,14 +39,6 @@
 	model = "NorthStar HR (BCM953012HR)";
 	compatible = "brcm,bcm953012hr", "brcm,brcm53012", "brcm,bcm4708";
 
-	aliases {
-		serial0 = &uart0;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
 	memory@80000000 {
 		reg = <0x80000000 0x10000000>;
 	};
diff --git a/arch/arm/boot/dts/bcm953012k.dts b/arch/arm/boot/dts/bcm953012k.dts
index a00c4e1dfb4c..fbc6219e977a 100644
--- a/arch/arm/boot/dts/bcm953012k.dts
+++ b/arch/arm/boot/dts/bcm953012k.dts
@@ -43,10 +43,6 @@
 		serial1 = &uart1;
 	};
 
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
 	memory {
 		reg = <0x00000000 0x10000000>;
 	};
-- 
2.11.0

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH V2 2/2] ARM: dts: BCM53573: Specify serial console parameters

[Rafał Miłecki]

From: Rafa? Mi?ecki <rafal@milecki.pl>

This adds baud rate, parity & number of data bits. It's required to get
serial working correctly.

Signed-off-by: Rafa? Mi?ecki <rafal@milecki.pl>
---
 arch/arm/boot/dts/bcm53573.dtsi | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/bcm53573.dtsi b/arch/arm/boot/dts/bcm53573.dtsi
index 71ce23e46d30..eae623f76401 100644
--- a/arch/arm/boot/dts/bcm53573.dtsi
+++ b/arch/arm/boot/dts/bcm53573.dtsi
@@ -13,8 +13,12 @@
 / {
 	interrupt-parent = <&gic>;
 
+	aliases {
+		serial0 = &uart0;
+	};
+
 	chosen {
-		stdout-path = &uart0;
+		stdout-path = "serial0:115200n8";
 	};
 
 	cpus {
-- 
2.11.0

[PATCH V2 2/2] ARM: dts: BCM53573: Specify serial console parameters

[Rafał Miłecki]

From: Rafał Miłecki <rafal-g1n6cQUeyibVItvQsEIGlw@public.gmane.org>

This adds baud rate, parity & number of data bits. It's required to get
serial working correctly.

Signed-off-by: Rafał Miłecki <rafal-g1n6cQUeyibVItvQsEIGlw@public.gmane.org>
---
 arch/arm/boot/dts/bcm53573.dtsi | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/bcm53573.dtsi b/arch/arm/boot/dts/bcm53573.dtsi
index 71ce23e46d30..eae623f76401 100644
--- a/arch/arm/boot/dts/bcm53573.dtsi
+++ b/arch/arm/boot/dts/bcm53573.dtsi
@@ -13,8 +13,12 @@
 / {
 	interrupt-parent = <&gic>;
 
+	aliases {
+		serial0 = &uart0;
+	};
+
 	chosen {
-		stdout-path = &uart0;
+		stdout-path = "serial0:115200n8";
 	};
 
 	cpus {
-- 
2.11.0

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH V2 1/2] ARM: dts: BCM5301X: Specify serial console params in dtsi files

[Florian Fainelli]

On 03/15/2017 10:03 AM, Rafa? Mi?ecki wrote:
> From: Rafa? Mi?ecki <rafal@milecki.pl>
> 
> So far every Northstar device we have seen was using the same serial
> console params (115200n8). It probably make the most sense to put it in
> some proper dtsi files instead of repeating over and over for every
> single device. As different boards may use different bootloaders it
> seems the safest idea is to use board specific dtsi files.
> 
> Just in case some vendor decides to use different UART (parameters) this
> can be always easily overwritten.
> 
> Signed-off-by: Rafa? Mi?ecki <rafal@milecki.pl>

Applied, thanks!
-- 
Florian

Re: [PATCH V2 1/2] ARM: dts: BCM5301X: Specify serial console params in dtsi files

[Florian Fainelli]

On 03/15/2017 10:03 AM, Rafał Miłecki wrote:
> From: Rafał Miłecki <rafal-g1n6cQUeyibVItvQsEIGlw@public.gmane.org>
> 
> So far every Northstar device we have seen was using the same serial
> console params (115200n8). It probably make the most sense to put it in
> some proper dtsi files instead of repeating over and over for every
> single device. As different boards may use different bootloaders it
> seems the safest idea is to use board specific dtsi files.
> 
> Just in case some vendor decides to use different UART (parameters) this
> can be always easily overwritten.
> 
> Signed-off-by: Rafał Miłecki <rafal-g1n6cQUeyibVItvQsEIGlw@public.gmane.org>

Applied, thanks!
-- 
Florian
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html