[PATCH v1 4/4] stmmac: pci: split out common_default_data() helper

[Andy Shevchenko <andriy.shevchenko@linux.intel.com>]

New helper is added in order to prevent misconfiguration happened
for one of the platforms when configuration data is expanded.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
---
 drivers/net/ethernet/stmicro/stmmac/stmmac_pci.c | 52 ++++++++----------------
 1 file changed, 18 insertions(+), 34 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_pci.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_pci.c
index 2456e0a945ef..22f910795be4 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_pci.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_pci.c
@@ -70,11 +70,8 @@ static int stmmac_pci_find_phy_addr(struct stmmac_pci_info *info)
 	return -ENODEV;
 }
 
-static void stmmac_default_data(struct plat_stmmacenet_data *plat)
+static void common_default_data(struct plat_stmmacenet_data *plat)
 {
-	plat->bus_id = 1;
-	plat->phy_addr = 0;
-	plat->interface = PHY_INTERFACE_MODE_GMII;
 	plat->clk_csr = 2;	/* clk_csr_i = 20-35MHz & MDC = clk_csr_i/16 */
 	plat->has_gmac = 1;
 	plat->force_sf_dma_mode = 1;
@@ -82,10 +79,6 @@ static void stmmac_default_data(struct plat_stmmacenet_data *plat)
 	plat->mdio_bus_data->phy_reset = NULL;
 	plat->mdio_bus_data->phy_mask = 0;
 
-	plat->dma_cfg->pbl = 32;
-	plat->dma_cfg->pblx8 = true;
-	/* TODO: AXI */
-
 	/* Set default value for multicast hash bins */
 	plat->multicast_filter_bins = HASH_TABLE_SIZE;
 
@@ -107,12 +100,29 @@ static void stmmac_default_data(struct plat_stmmacenet_data *plat)
 	plat->rx_queues_cfg[0].pkt_route = 0x0;
 }
 
+static void stmmac_default_data(struct plat_stmmacenet_data *plat)
+{
+	/* Set common default data first */
+	common_default_data(plat);
+
+	plat->bus_id = 1;
+	plat->phy_addr = 0;
+	plat->interface = PHY_INTERFACE_MODE_GMII;
+
+	plat->dma_cfg->pbl = 32;
+	plat->dma_cfg->pblx8 = true;
+	/* TODO: AXI */
+}
+
 static int quark_default_data(struct plat_stmmacenet_data *plat,
 			      struct stmmac_pci_info *info)
 {
 	struct pci_dev *pdev = info->pdev;
 	int ret;
 
+	/* Set common default data first */
+	common_default_data(plat);
+
 	/*
 	 * Refuse to load the driver and register net device if MAC controller
 	 * does not connect to any PHY interface.
@@ -124,38 +134,12 @@ static int quark_default_data(struct plat_stmmacenet_data *plat,
 	plat->bus_id = PCI_DEVID(pdev->bus->number, pdev->devfn);
 	plat->phy_addr = ret;
 	plat->interface = PHY_INTERFACE_MODE_RMII;
-	plat->clk_csr = 2;
-	plat->has_gmac = 1;
-	plat->force_sf_dma_mode = 1;
-
-	plat->mdio_bus_data->phy_reset = NULL;
-	plat->mdio_bus_data->phy_mask = 0;
 
 	plat->dma_cfg->pbl = 16;
 	plat->dma_cfg->pblx8 = true;
 	plat->dma_cfg->fixed_burst = 1;
 	/* AXI (TODO) */
 
-	/* Set default value for multicast hash bins */
-	plat->multicast_filter_bins = HASH_TABLE_SIZE;
-
-	/* Set default value for unicast filter entries */
-	plat->unicast_filter_entries = 1;
-
-	/* Set the maxmtu to a default of JUMBO_LEN */
-	plat->maxmtu = JUMBO_LEN;
-
-	/* Set default number of RX and TX queues to use */
-	plat->tx_queues_to_use = 1;
-	plat->rx_queues_to_use = 1;
-
-	/* Disable Priority config by default */
-	plat->tx_queues_cfg[0].use_prio = false;
-	plat->rx_queues_cfg[0].use_prio = false;
-
-	/* Disable RX queues routing by default */
-	plat->rx_queues_cfg[0].pkt_route = 0x0;
-
 	return 0;
 }
 
-- 
2.11.0