From: Tvrtko Ursulin <tursulin@ursulin.net>
To: Intel-gfx@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org,
Masahiro Yamada <yamada.masahiro@socionext.com>,
Andy Shevchenko <andy.shevchenko@gmail.com>
Subject: [PATCH v6 2/5] lib/scatterlist: Avoid potential scatterlist entry overflow
Date: Thu, 3 Aug 2017 10:13:12 +0100 [thread overview]
Message-ID: <20170803091312.22875-1-tvrtko.ursulin@linux.intel.com> (raw)
In-Reply-To: <20170731185512.20010-2-tvrtko.ursulin@linux.intel.com>
From: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Since the scatterlist length field is an unsigned int, make
sure that sg_alloc_table_from_pages does not overflow it while
coalescing pages to a single entry.
v2: Drop reference to future use. Use UINT_MAX.
v3: max_segment must be page aligned.
v4: Do not rely on compiler to optimise out the rounddown.
(Joonas Lahtinen)
v5: Simplified loops and use post-increments rather than
pre-increments. Use PAGE_MASK and fix comment typo.
(Andy Shevchenko)
v6: Commit spelling fix.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
---
include/linux/scatterlist.h | 6 ++++++
lib/scatterlist.c | 31 ++++++++++++++++++++-----------
2 files changed, 26 insertions(+), 11 deletions(-)
diff --git a/include/linux/scatterlist.h b/include/linux/scatterlist.h
index 205aefb4ed93..6dd2ddbc6230 100644
--- a/include/linux/scatterlist.h
+++ b/include/linux/scatterlist.h
@@ -21,6 +21,12 @@ struct scatterlist {
};
/*
+ * Since the above length field is an unsigned int, below we define the maximum
+ * length in bytes that can be stored in one scatterlist entry.
+ */
+#define SCATTERLIST_MAX_SEGMENT (UINT_MAX & PAGE_MASK)
+
+/*
* These macros should be used after a dma_map_sg call has been done
* to get bus addresses of each of the SG entries and their lengths.
* You should only work with the number of sg entries dma_map_sg
diff --git a/lib/scatterlist.c b/lib/scatterlist.c
index dee0c5004e2f..7b2e74da2c44 100644
--- a/lib/scatterlist.c
+++ b/lib/scatterlist.c
@@ -394,17 +394,22 @@ int sg_alloc_table_from_pages(struct sg_table *sgt,
unsigned int offset, unsigned long size,
gfp_t gfp_mask)
{
- unsigned int chunks;
- unsigned int i;
- unsigned int cur_page;
+ const unsigned int max_segment = SCATTERLIST_MAX_SEGMENT;
+ unsigned int chunks, cur_page, seg_len, i;
int ret;
struct scatterlist *s;
/* compute number of contiguous chunks */
chunks = 1;
- for (i = 1; i < n_pages; ++i)
- if (page_to_pfn(pages[i]) != page_to_pfn(pages[i - 1]) + 1)
- ++chunks;
+ seg_len = 0;
+ for (i = 1; i < n_pages; i++) {
+ seg_len += PAGE_SIZE;
+ if (seg_len >= max_segment ||
+ page_to_pfn(pages[i]) != page_to_pfn(pages[i - 1]) + 1) {
+ chunks++;
+ seg_len = 0;
+ }
+ }
ret = sg_alloc_table(sgt, chunks, gfp_mask);
if (unlikely(ret))
@@ -413,17 +418,21 @@ int sg_alloc_table_from_pages(struct sg_table *sgt,
/* merging chunks and putting them into the scatterlist */
cur_page = 0;
for_each_sg(sgt->sgl, s, sgt->orig_nents, i) {
- unsigned long chunk_size;
- unsigned int j;
+ unsigned int j, chunk_size;
/* look for the end of the current chunk */
- for (j = cur_page + 1; j < n_pages; ++j)
- if (page_to_pfn(pages[j]) !=
+ seg_len = 0;
+ for (j = cur_page + 1; j < n_pages; j++) {
+ seg_len += PAGE_SIZE;
+ if (seg_len >= max_segment ||
+ page_to_pfn(pages[j]) !=
page_to_pfn(pages[j - 1]) + 1)
break;
+ }
chunk_size = ((j - cur_page) << PAGE_SHIFT) - offset;
- sg_set_page(s, pages[cur_page], min(size, chunk_size), offset);
+ sg_set_page(s, pages[cur_page],
+ min_t(unsigned long, size, chunk_size), offset);
size -= chunk_size;
offset = 0;
cur_page = j;
--
2.9.4
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
WARNING: multiple messages have this Message-ID (diff)
From: Tvrtko Ursulin <tursulin@ursulin.net>
To: Intel-gfx@lists.freedesktop.org
Cc: tursulin@ursulin.net, Tvrtko Ursulin <tvrtko.ursulin@intel.com>,
Masahiro Yamada <yamada.masahiro@socionext.com>,
linux-kernel@vger.kernel.org,
Joonas Lahtinen <joonas.lahtinen@linux.intel.com>,
Andy Shevchenko <andy.shevchenko@gmail.com>
Subject: [PATCH v6 2/5] lib/scatterlist: Avoid potential scatterlist entry overflow
Date: Thu, 3 Aug 2017 10:13:12 +0100 [thread overview]
Message-ID: <20170803091312.22875-1-tvrtko.ursulin@linux.intel.com> (raw)
In-Reply-To: <20170731185512.20010-2-tvrtko.ursulin@linux.intel.com>
From: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Since the scatterlist length field is an unsigned int, make
sure that sg_alloc_table_from_pages does not overflow it while
coalescing pages to a single entry.
v2: Drop reference to future use. Use UINT_MAX.
v3: max_segment must be page aligned.
v4: Do not rely on compiler to optimise out the rounddown.
(Joonas Lahtinen)
v5: Simplified loops and use post-increments rather than
pre-increments. Use PAGE_MASK and fix comment typo.
(Andy Shevchenko)
v6: Commit spelling fix.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
---
include/linux/scatterlist.h | 6 ++++++
lib/scatterlist.c | 31 ++++++++++++++++++++-----------
2 files changed, 26 insertions(+), 11 deletions(-)
diff --git a/include/linux/scatterlist.h b/include/linux/scatterlist.h
index 205aefb4ed93..6dd2ddbc6230 100644
--- a/include/linux/scatterlist.h
+++ b/include/linux/scatterlist.h
@@ -21,6 +21,12 @@ struct scatterlist {
};
/*
+ * Since the above length field is an unsigned int, below we define the maximum
+ * length in bytes that can be stored in one scatterlist entry.
+ */
+#define SCATTERLIST_MAX_SEGMENT (UINT_MAX & PAGE_MASK)
+
+/*
* These macros should be used after a dma_map_sg call has been done
* to get bus addresses of each of the SG entries and their lengths.
* You should only work with the number of sg entries dma_map_sg
diff --git a/lib/scatterlist.c b/lib/scatterlist.c
index dee0c5004e2f..7b2e74da2c44 100644
--- a/lib/scatterlist.c
+++ b/lib/scatterlist.c
@@ -394,17 +394,22 @@ int sg_alloc_table_from_pages(struct sg_table *sgt,
unsigned int offset, unsigned long size,
gfp_t gfp_mask)
{
- unsigned int chunks;
- unsigned int i;
- unsigned int cur_page;
+ const unsigned int max_segment = SCATTERLIST_MAX_SEGMENT;
+ unsigned int chunks, cur_page, seg_len, i;
int ret;
struct scatterlist *s;
/* compute number of contiguous chunks */
chunks = 1;
- for (i = 1; i < n_pages; ++i)
- if (page_to_pfn(pages[i]) != page_to_pfn(pages[i - 1]) + 1)
- ++chunks;
+ seg_len = 0;
+ for (i = 1; i < n_pages; i++) {
+ seg_len += PAGE_SIZE;
+ if (seg_len >= max_segment ||
+ page_to_pfn(pages[i]) != page_to_pfn(pages[i - 1]) + 1) {
+ chunks++;
+ seg_len = 0;
+ }
+ }
ret = sg_alloc_table(sgt, chunks, gfp_mask);
if (unlikely(ret))
@@ -413,17 +418,21 @@ int sg_alloc_table_from_pages(struct sg_table *sgt,
/* merging chunks and putting them into the scatterlist */
cur_page = 0;
for_each_sg(sgt->sgl, s, sgt->orig_nents, i) {
- unsigned long chunk_size;
- unsigned int j;
+ unsigned int j, chunk_size;
/* look for the end of the current chunk */
- for (j = cur_page + 1; j < n_pages; ++j)
- if (page_to_pfn(pages[j]) !=
+ seg_len = 0;
+ for (j = cur_page + 1; j < n_pages; j++) {
+ seg_len += PAGE_SIZE;
+ if (seg_len >= max_segment ||
+ page_to_pfn(pages[j]) !=
page_to_pfn(pages[j - 1]) + 1)
break;
+ }
chunk_size = ((j - cur_page) << PAGE_SHIFT) - offset;
- sg_set_page(s, pages[cur_page], min(size, chunk_size), offset);
+ sg_set_page(s, pages[cur_page],
+ min_t(unsigned long, size, chunk_size), offset);
size -= chunk_size;
offset = 0;
cur_page = j;
--
2.9.4
next prev parent reply other threads:[~2017-08-03 9:13 UTC|newest]
Thread overview: 30+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-07-31 18:55 [PATCH 1/5] lib/scatterlist: Fix offset type in sg_alloc_table_from_pages Tvrtko Ursulin
2017-07-31 18:55 ` [PATCH 2/5] lib/scatterlist: Avoid potential scatterlist entry overflow Tvrtko Ursulin
2017-07-31 18:55 ` Tvrtko Ursulin
2017-08-03 9:13 ` Tvrtko Ursulin [this message]
2017-08-03 9:13 ` [PATCH v6 " Tvrtko Ursulin
2017-07-31 18:55 ` [PATCH 3/5] lib/scatterlist: Introduce and export __sg_alloc_table_from_pages Tvrtko Ursulin
2017-07-31 18:55 ` Tvrtko Ursulin
2017-08-03 9:13 ` [PATCH v7 " Tvrtko Ursulin
2017-08-03 9:13 ` Tvrtko Ursulin
2017-07-31 18:55 ` [PATCH 4/5] drm/i915: Use __sg_alloc_table_from_pages for userptr allocations Tvrtko Ursulin
2017-07-31 18:55 ` Tvrtko Ursulin
2017-08-03 9:14 ` [PATCH v8 " Tvrtko Ursulin
2017-08-03 9:14 ` Tvrtko Ursulin
2017-07-31 18:55 ` [PATCH 5/5] tools/testing/scatterlist: Test new __sg_alloc_table_from_pages Tvrtko Ursulin
2017-07-31 18:55 ` Tvrtko Ursulin
2017-09-05 10:24 ` [PATCH v2 " Tvrtko Ursulin
2017-09-06 10:48 ` Chris Wilson
2017-09-06 10:48 ` Chris Wilson
2017-09-06 12:10 ` Tvrtko Ursulin
2017-09-06 12:10 ` [Intel-gfx] " Tvrtko Ursulin
2017-09-06 12:39 ` Chris Wilson
2017-09-06 14:55 ` [PATCH v3 " Tvrtko Ursulin
2017-09-06 14:55 ` Tvrtko Ursulin
2017-07-31 19:25 ` ✓ Fi.CI.BAT: success for series starting with [1/5] lib/scatterlist: Fix offset type in sg_alloc_table_from_pages Patchwork
2017-08-03 9:41 ` ✓ Fi.CI.BAT: success for series starting with [1/5] lib/scatterlist: Fix offset type in sg_alloc_table_from_pages (rev4) Patchwork
2017-09-05 10:42 ` ✓ Fi.CI.BAT: success for series starting with [1/5] lib/scatterlist: Fix offset type in sg_alloc_table_from_pages (rev5) Patchwork
2017-09-05 11:54 ` ✓ Fi.CI.IGT: " Patchwork
2017-09-06 15:32 ` ✗ Fi.CI.BAT: failure for series starting with [1/5] lib/scatterlist: Fix offset type in sg_alloc_table_from_pages (rev6) Patchwork
2017-09-07 9:22 ` ✓ Fi.CI.BAT: success " Patchwork
2017-09-07 10:49 ` ✗ Fi.CI.IGT: failure " Patchwork
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20170803091312.22875-1-tvrtko.ursulin@linux.intel.com \
--to=tursulin@ursulin.net \
--cc=Intel-gfx@lists.freedesktop.org \
--cc=andy.shevchenko@gmail.com \
--cc=linux-kernel@vger.kernel.org \
--cc=yamada.masahiro@socionext.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.