[PATCH v5 05/10] dt-bindings: net: dwmac-sun8i: update documentation about integrated PHY

[clabbe.montjoie@gmail.com (Corentin Labbe)]

On Tue, Sep 19, 2017 at 09:49:52PM -0500, Rob Herring wrote:
> On Thu, Sep 14, 2017 at 2:19 PM, Andrew Lunn <andrew@lunn.ch> wrote:
> >> > Is the MDIO controller "allwinner,sun8i-h3-emac" or "snps,dwmac-mdio"?
> >> > If the latter, then I think the node is fine, but then the mux should be
> >> > a child node of it. IOW, the child of an MDIO controller should either
> >> > be a mux node or slave devices.
> >
> > Hi Rob
> >
> > Up until now, children of an MDIO bus have been MDIO devices. Those
> > MDIO devices are either Ethernet PHYs, Ethernet Switches, or the
> > oddball devices that Broadcom iProc has, like generic PHYs.
> >
> > We have never had MDIO-muxes as MDIO children. A Mux is not an MDIO
> > device, and does not have the properties of an MDIO device. It is not
> > addressable on the MDIO bus. The current MUXes are addressed via GPIOs
> > or MMIO.
> 
> The DT parent/child relationship defines the bus topology. We describe
> MDIO buses in that way and if a mux is sitting between the controller
> and the devices, then the DT hierarchy should reflect that. Now
> sometimes we have 2 options for what interface has the parent/child
> relationship (e.g. an I2C controlled USB hub chip), but in this case
> we don't.
> 

Putting mdio-mux as a child of it (the mdio node) give me:
[   18.175338] libphy: stmmac: probed
[   18.175379] mdio_bus stmmac-0: /soc/ethernet at 1c30000/mdio/mdio-mux has invalid PHY address
[   18.175408] mdio_bus stmmac-0: scan phy mdio-mux at address 0
[   18.175450] mdio_bus stmmac-0: scan phy mdio-mux at address 1
[   18.175482] mdio_bus stmmac-0: scan phy mdio-mux at address 2
[   18.175513] mdio_bus stmmac-0: scan phy mdio-mux at address 3
[   18.175544] mdio_bus stmmac-0: scan phy mdio-mux at address 4
[   18.175575] mdio_bus stmmac-0: scan phy mdio-mux at address 5
[   18.175607] mdio_bus stmmac-0: scan phy mdio-mux at address 6
[   18.175638] mdio_bus stmmac-0: scan phy mdio-mux at address 7
[   18.175669] mdio_bus stmmac-0: scan phy mdio-mux at address 8
[   18.175700] mdio_bus stmmac-0: scan phy mdio-mux at address 9
[   18.175731] mdio_bus stmmac-0: scan phy mdio-mux at address 10
[   18.175762] mdio_bus stmmac-0: scan phy mdio-mux at address 11
[   18.175795] mdio_bus stmmac-0: scan phy mdio-mux at address 12
[   18.175827] mdio_bus stmmac-0: scan phy mdio-mux at address 13
[   18.175858] mdio_bus stmmac-0: scan phy mdio-mux at address 14
[   18.175889] mdio_bus stmmac-0: scan phy mdio-mux at address 15
[   18.175919] mdio_bus stmmac-0: scan phy mdio-mux at address 16
[   18.175951] mdio_bus stmmac-0: scan phy mdio-mux at address 17
[   18.175982] mdio_bus stmmac-0: scan phy mdio-mux at address 18
[   18.176014] mdio_bus stmmac-0: scan phy mdio-mux at address 19
[   18.176045] mdio_bus stmmac-0: scan phy mdio-mux at address 20
[   18.176076] mdio_bus stmmac-0: scan phy mdio-mux at address 21
[   18.176107] mdio_bus stmmac-0: scan phy mdio-mux at address 22
[   18.176139] mdio_bus stmmac-0: scan phy mdio-mux at address 23
[   18.176170] mdio_bus stmmac-0: scan phy mdio-mux at address 24
[   18.176202] mdio_bus stmmac-0: scan phy mdio-mux at address 25
[   18.176233] mdio_bus stmmac-0: scan phy mdio-mux at address 26
[   18.176271] mdio_bus stmmac-0: scan phy mdio-mux at address 27
[   18.176320] mdio_bus stmmac-0: scan phy mdio-mux at address 28
[   18.176371] mdio_bus stmmac-0: scan phy mdio-mux at address 29
[   18.176420] mdio_bus stmmac-0: scan phy mdio-mux at address 30
[   18.176452] mdio_bus stmmac-0: scan phy mdio-mux at address 31

Adding a fake <reg> to mdio-mux remove it, but I found that a bit ugly.
Or perhaps patching of_mdiobus_register() to not scan node with compatible "mdio-mux".

What do you think ?

Regards