From: Tony Lindgren <tony-4v6yS6AI5VpBDgjK7y7TUQ@public.gmane.org>
To: linux-omap-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org,
"Benoît Cousson"
<bcousson-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>,
devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
"Tero Kristo" <t-kristo-l0cyMroinI0@public.gmane.org>
Subject: [PATCH 04/10] ARM: dts: omap4: add clkctrl nodes
Date: Wed, 20 Sep 2017 15:46:15 -0700 [thread overview]
Message-ID: <20170920224621.16236-5-tony@atomide.com> (raw)
In-Reply-To: <20170920224621.16236-1-tony-4v6yS6AI5VpBDgjK7y7TUQ@public.gmane.org>
From: Tero Kristo <t-kristo-l0cyMroinI0@public.gmane.org>
Add clkctrl nodes for OMAP4 SoC. These are going to be acting as
replacement for part of the existing clock data and the existing
clkctrl hooks under hwmod data.
Signed-off-by: Tero Kristo <t-kristo-l0cyMroinI0@public.gmane.org>
Signed-off-by: Tony Lindgren <tony-4v6yS6AI5VpBDgjK7y7TUQ@public.gmane.org>
---
arch/arm/boot/dts/omap4.dtsi | 1 +
arch/arm/boot/dts/omap44xx-clocks.dtsi | 289 +++++++++++++++++++++++++++++++++
2 files changed, 290 insertions(+)
diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi
--- a/arch/arm/boot/dts/omap4.dtsi
+++ b/arch/arm/boot/dts/omap4.dtsi
@@ -9,6 +9,7 @@
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/pinctrl/omap.h>
+#include <dt-bindings/clock/omap4.h>
/ {
compatible = "ti,omap4430", "ti,omap4";
diff --git a/arch/arm/boot/dts/omap44xx-clocks.dtsi b/arch/arm/boot/dts/omap44xx-clocks.dtsi
--- a/arch/arm/boot/dts/omap44xx-clocks.dtsi
+++ b/arch/arm/boot/dts/omap44xx-clocks.dtsi
@@ -628,6 +628,7 @@
clock-frequency = <0>;
};
};
+
&prm_clocks {
sys_clkin_ck: sys_clkin_ck@110 {
#clock-cells = <0>;
@@ -1631,3 +1632,291 @@
reg = <0x0224>;
};
};
+
+&cm1 {
+ mpuss_cm: mpuss_cm@300 {
+ compatible = "ti,omap4-cm";
+ reg = <0x300 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x300 0x100>;
+
+ mpuss_clkctrl: clk@20 {
+ compatible = "ti,clkctrl";
+ reg = <0x20 0x4>;
+ #clock-cells = <2>;
+ };
+ };
+
+ tesla_cm: tesla_cm@400 {
+ compatible = "ti,omap4-cm";
+ reg = <0x400 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x400 0x100>;
+
+ tesla_clkctrl: clk@20 {
+ compatible = "ti,clkctrl";
+ reg = <0x20 0x4>;
+ #clock-cells = <2>;
+ };
+ };
+
+ abe_cm: abe_cm@500 {
+ compatible = "ti,omap4-cm";
+ reg = <0x500 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x500 0x100>;
+
+ abe_clkctrl: clk@20 {
+ compatible = "ti,clkctrl";
+ reg = <0x20 0x6c>;
+ #clock-cells = <2>;
+ };
+ };
+
+};
+
+&cm2 {
+ l4_ao_cm: l4_ao_cm@600 {
+ compatible = "ti,omap4-cm";
+ reg = <0x600 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x600 0x100>;
+
+ l4_ao_clkctrl: clk@20 {
+ compatible = "ti,clkctrl";
+ reg = <0x20 0x1c>;
+ #clock-cells = <2>;
+ };
+ };
+
+ l3_1_cm: l3_1_cm@700 {
+ compatible = "ti,omap4-cm";
+ reg = <0x700 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x700 0x100>;
+
+ l3_1_clkctrl: clk@20 {
+ compatible = "ti,clkctrl";
+ reg = <0x20 0x4>;
+ #clock-cells = <2>;
+ };
+ };
+
+ l3_2_cm: l3_2_cm@800 {
+ compatible = "ti,omap4-cm";
+ reg = <0x800 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x800 0x100>;
+
+ l3_2_clkctrl: clk@20 {
+ compatible = "ti,clkctrl";
+ reg = <0x20 0x14>;
+ #clock-cells = <2>;
+ };
+ };
+
+ ducati_cm: ducati_cm@900 {
+ compatible = "ti,omap4-cm";
+ reg = <0x900 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x900 0x100>;
+
+ ducati_clkctrl: clk@20 {
+ compatible = "ti,clkctrl";
+ reg = <0x20 0x4>;
+ #clock-cells = <2>;
+ };
+ };
+
+ l3_dma_cm: l3_dma_cm@a00 {
+ compatible = "ti,omap4-cm";
+ reg = <0xa00 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0xa00 0x100>;
+
+ l3_dma_clkctrl: clk@20 {
+ compatible = "ti,clkctrl";
+ reg = <0x20 0x4>;
+ #clock-cells = <2>;
+ };
+ };
+
+ l3_emif_cm: l3_emif_cm@b00 {
+ compatible = "ti,omap4-cm";
+ reg = <0xb00 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0xb00 0x100>;
+
+ l3_emif_clkctrl: clk@20 {
+ compatible = "ti,clkctrl";
+ reg = <0x20 0x1c>;
+ #clock-cells = <2>;
+ };
+ };
+
+ d2d_cm: d2d_cm@c00 {
+ compatible = "ti,omap4-cm";
+ reg = <0xc00 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0xc00 0x100>;
+
+ d2d_clkctrl: clk@20 {
+ compatible = "ti,clkctrl";
+ reg = <0x20 0x4>;
+ #clock-cells = <2>;
+ };
+ };
+
+ l4_cfg_cm: l4_cfg_cm@d00 {
+ compatible = "ti,omap4-cm";
+ reg = <0xd00 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0xd00 0x100>;
+
+ l4_cfg_clkctrl: clk@20 {
+ compatible = "ti,clkctrl";
+ reg = <0x20 0x14>;
+ #clock-cells = <2>;
+ };
+ };
+
+ l3_instr_cm: l3_instr_cm@e00 {
+ compatible = "ti,omap4-cm";
+ reg = <0xe00 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0xe00 0x100>;
+
+ l3_instr_clkctrl: clk@20 {
+ compatible = "ti,clkctrl";
+ reg = <0x20 0x24>;
+ #clock-cells = <2>;
+ };
+ };
+
+ ivahd_cm: ivahd_cm@f00 {
+ compatible = "ti,omap4-cm";
+ reg = <0xf00 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0xf00 0x100>;
+
+ ivahd_clkctrl: clk@20 {
+ compatible = "ti,clkctrl";
+ reg = <0x20 0xc>;
+ #clock-cells = <2>;
+ };
+ };
+
+ iss_cm: iss_cm@1000 {
+ compatible = "ti,omap4-cm";
+ reg = <0x1000 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x1000 0x100>;
+
+ iss_clkctrl: clk@20 {
+ compatible = "ti,clkctrl";
+ reg = <0x20 0xc>;
+ #clock-cells = <2>;
+ };
+ };
+
+ l3_dss_cm: l3_dss_cm@1100 {
+ compatible = "ti,omap4-cm";
+ reg = <0x1100 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x1100 0x100>;
+
+ l3_dss_clkctrl: clk@20 {
+ compatible = "ti,clkctrl";
+ reg = <0x20 0x4>;
+ #clock-cells = <2>;
+ };
+ };
+
+ l3_gfx_cm: l3_gfx_cm@1200 {
+ compatible = "ti,omap4-cm";
+ reg = <0x1200 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x1200 0x100>;
+
+ l3_gfx_clkctrl: clk@20 {
+ compatible = "ti,clkctrl";
+ reg = <0x20 0x4>;
+ #clock-cells = <2>;
+ };
+ };
+
+ l3_init_cm: l3_init_cm@1300 {
+ compatible = "ti,omap4-cm";
+ reg = <0x1300 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x1300 0x100>;
+
+ l3_init_clkctrl: clk@20 {
+ compatible = "ti,clkctrl";
+ reg = <0x20 0xc4>;
+ #clock-cells = <2>;
+ };
+ };
+
+ l4_per_cm: l4_per_cm@1400 {
+ compatible = "ti,omap4-cm";
+ reg = <0x1400 0x200>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x1400 0x200>;
+
+ l4_per_clkctrl: clk@20 {
+ compatible = "ti,clkctrl";
+ reg = <0x20 0x144>;
+ #clock-cells = <2>;
+ };
+ };
+
+};
+
+&prm {
+ l4_wkup_cm: l4_wkup_cm@1800 {
+ compatible = "ti,omap4-cm";
+ reg = <0x1800 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x1800 0x100>;
+
+ l4_wkup_clkctrl: clk@20 {
+ compatible = "ti,clkctrl";
+ reg = <0x20 0x5c>;
+ #clock-cells = <2>;
+ };
+ };
+
+ emu_sys_cm: emu_sys_cm@1a00 {
+ compatible = "ti,omap4-cm";
+ reg = <0x1a00 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x1a00 0x100>;
+
+ emu_sys_clkctrl: clk@20 {
+ compatible = "ti,clkctrl";
+ reg = <0x20 0x4>;
+ #clock-cells = <2>;
+ };
+ };
+};
--
2.14.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
WARNING: multiple messages have this Message-ID (diff)
From: tony@atomide.com (Tony Lindgren)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 04/10] ARM: dts: omap4: add clkctrl nodes
Date: Wed, 20 Sep 2017 15:46:15 -0700 [thread overview]
Message-ID: <20170920224621.16236-5-tony@atomide.com> (raw)
In-Reply-To: <20170920224621.16236-1-tony@atomide.com>
From: Tero Kristo <t-kristo@ti.com>
Add clkctrl nodes for OMAP4 SoC. These are going to be acting as
replacement for part of the existing clock data and the existing
clkctrl hooks under hwmod data.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/boot/dts/omap4.dtsi | 1 +
arch/arm/boot/dts/omap44xx-clocks.dtsi | 289 +++++++++++++++++++++++++++++++++
2 files changed, 290 insertions(+)
diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi
--- a/arch/arm/boot/dts/omap4.dtsi
+++ b/arch/arm/boot/dts/omap4.dtsi
@@ -9,6 +9,7 @@
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/pinctrl/omap.h>
+#include <dt-bindings/clock/omap4.h>
/ {
compatible = "ti,omap4430", "ti,omap4";
diff --git a/arch/arm/boot/dts/omap44xx-clocks.dtsi b/arch/arm/boot/dts/omap44xx-clocks.dtsi
--- a/arch/arm/boot/dts/omap44xx-clocks.dtsi
+++ b/arch/arm/boot/dts/omap44xx-clocks.dtsi
@@ -628,6 +628,7 @@
clock-frequency = <0>;
};
};
+
&prm_clocks {
sys_clkin_ck: sys_clkin_ck at 110 {
#clock-cells = <0>;
@@ -1631,3 +1632,291 @@
reg = <0x0224>;
};
};
+
+&cm1 {
+ mpuss_cm: mpuss_cm at 300 {
+ compatible = "ti,omap4-cm";
+ reg = <0x300 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x300 0x100>;
+
+ mpuss_clkctrl: clk at 20 {
+ compatible = "ti,clkctrl";
+ reg = <0x20 0x4>;
+ #clock-cells = <2>;
+ };
+ };
+
+ tesla_cm: tesla_cm at 400 {
+ compatible = "ti,omap4-cm";
+ reg = <0x400 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x400 0x100>;
+
+ tesla_clkctrl: clk at 20 {
+ compatible = "ti,clkctrl";
+ reg = <0x20 0x4>;
+ #clock-cells = <2>;
+ };
+ };
+
+ abe_cm: abe_cm at 500 {
+ compatible = "ti,omap4-cm";
+ reg = <0x500 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x500 0x100>;
+
+ abe_clkctrl: clk at 20 {
+ compatible = "ti,clkctrl";
+ reg = <0x20 0x6c>;
+ #clock-cells = <2>;
+ };
+ };
+
+};
+
+&cm2 {
+ l4_ao_cm: l4_ao_cm at 600 {
+ compatible = "ti,omap4-cm";
+ reg = <0x600 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x600 0x100>;
+
+ l4_ao_clkctrl: clk at 20 {
+ compatible = "ti,clkctrl";
+ reg = <0x20 0x1c>;
+ #clock-cells = <2>;
+ };
+ };
+
+ l3_1_cm: l3_1_cm at 700 {
+ compatible = "ti,omap4-cm";
+ reg = <0x700 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x700 0x100>;
+
+ l3_1_clkctrl: clk at 20 {
+ compatible = "ti,clkctrl";
+ reg = <0x20 0x4>;
+ #clock-cells = <2>;
+ };
+ };
+
+ l3_2_cm: l3_2_cm at 800 {
+ compatible = "ti,omap4-cm";
+ reg = <0x800 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x800 0x100>;
+
+ l3_2_clkctrl: clk at 20 {
+ compatible = "ti,clkctrl";
+ reg = <0x20 0x14>;
+ #clock-cells = <2>;
+ };
+ };
+
+ ducati_cm: ducati_cm at 900 {
+ compatible = "ti,omap4-cm";
+ reg = <0x900 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x900 0x100>;
+
+ ducati_clkctrl: clk at 20 {
+ compatible = "ti,clkctrl";
+ reg = <0x20 0x4>;
+ #clock-cells = <2>;
+ };
+ };
+
+ l3_dma_cm: l3_dma_cm at a00 {
+ compatible = "ti,omap4-cm";
+ reg = <0xa00 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0xa00 0x100>;
+
+ l3_dma_clkctrl: clk at 20 {
+ compatible = "ti,clkctrl";
+ reg = <0x20 0x4>;
+ #clock-cells = <2>;
+ };
+ };
+
+ l3_emif_cm: l3_emif_cm at b00 {
+ compatible = "ti,omap4-cm";
+ reg = <0xb00 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0xb00 0x100>;
+
+ l3_emif_clkctrl: clk at 20 {
+ compatible = "ti,clkctrl";
+ reg = <0x20 0x1c>;
+ #clock-cells = <2>;
+ };
+ };
+
+ d2d_cm: d2d_cm at c00 {
+ compatible = "ti,omap4-cm";
+ reg = <0xc00 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0xc00 0x100>;
+
+ d2d_clkctrl: clk at 20 {
+ compatible = "ti,clkctrl";
+ reg = <0x20 0x4>;
+ #clock-cells = <2>;
+ };
+ };
+
+ l4_cfg_cm: l4_cfg_cm at d00 {
+ compatible = "ti,omap4-cm";
+ reg = <0xd00 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0xd00 0x100>;
+
+ l4_cfg_clkctrl: clk at 20 {
+ compatible = "ti,clkctrl";
+ reg = <0x20 0x14>;
+ #clock-cells = <2>;
+ };
+ };
+
+ l3_instr_cm: l3_instr_cm at e00 {
+ compatible = "ti,omap4-cm";
+ reg = <0xe00 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0xe00 0x100>;
+
+ l3_instr_clkctrl: clk at 20 {
+ compatible = "ti,clkctrl";
+ reg = <0x20 0x24>;
+ #clock-cells = <2>;
+ };
+ };
+
+ ivahd_cm: ivahd_cm at f00 {
+ compatible = "ti,omap4-cm";
+ reg = <0xf00 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0xf00 0x100>;
+
+ ivahd_clkctrl: clk at 20 {
+ compatible = "ti,clkctrl";
+ reg = <0x20 0xc>;
+ #clock-cells = <2>;
+ };
+ };
+
+ iss_cm: iss_cm at 1000 {
+ compatible = "ti,omap4-cm";
+ reg = <0x1000 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x1000 0x100>;
+
+ iss_clkctrl: clk at 20 {
+ compatible = "ti,clkctrl";
+ reg = <0x20 0xc>;
+ #clock-cells = <2>;
+ };
+ };
+
+ l3_dss_cm: l3_dss_cm at 1100 {
+ compatible = "ti,omap4-cm";
+ reg = <0x1100 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x1100 0x100>;
+
+ l3_dss_clkctrl: clk at 20 {
+ compatible = "ti,clkctrl";
+ reg = <0x20 0x4>;
+ #clock-cells = <2>;
+ };
+ };
+
+ l3_gfx_cm: l3_gfx_cm at 1200 {
+ compatible = "ti,omap4-cm";
+ reg = <0x1200 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x1200 0x100>;
+
+ l3_gfx_clkctrl: clk at 20 {
+ compatible = "ti,clkctrl";
+ reg = <0x20 0x4>;
+ #clock-cells = <2>;
+ };
+ };
+
+ l3_init_cm: l3_init_cm at 1300 {
+ compatible = "ti,omap4-cm";
+ reg = <0x1300 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x1300 0x100>;
+
+ l3_init_clkctrl: clk at 20 {
+ compatible = "ti,clkctrl";
+ reg = <0x20 0xc4>;
+ #clock-cells = <2>;
+ };
+ };
+
+ l4_per_cm: l4_per_cm at 1400 {
+ compatible = "ti,omap4-cm";
+ reg = <0x1400 0x200>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x1400 0x200>;
+
+ l4_per_clkctrl: clk at 20 {
+ compatible = "ti,clkctrl";
+ reg = <0x20 0x144>;
+ #clock-cells = <2>;
+ };
+ };
+
+};
+
+&prm {
+ l4_wkup_cm: l4_wkup_cm at 1800 {
+ compatible = "ti,omap4-cm";
+ reg = <0x1800 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x1800 0x100>;
+
+ l4_wkup_clkctrl: clk at 20 {
+ compatible = "ti,clkctrl";
+ reg = <0x20 0x5c>;
+ #clock-cells = <2>;
+ };
+ };
+
+ emu_sys_cm: emu_sys_cm at 1a00 {
+ compatible = "ti,omap4-cm";
+ reg = <0x1a00 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x1a00 0x100>;
+
+ emu_sys_clkctrl: clk at 20 {
+ compatible = "ti,clkctrl";
+ reg = <0x20 0x4>;
+ #clock-cells = <2>;
+ };
+ };
+};
--
2.14.1
next prev parent reply other threads:[~2017-09-20 22:46 UTC|newest]
Thread overview: 42+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-09-20 22:46 [PATCHv3 00/10] Fix remaining issues to drop more omap platform data Tony Lindgren
2017-09-20 22:46 ` Tony Lindgren
2017-09-20 22:46 ` [PATCH 02/10] ARM: dts: omap4: add fck under timer1 Tony Lindgren
2017-09-20 22:46 ` Tony Lindgren
2017-09-20 22:46 ` [PATCH 03/10] ARM: dts: omap4: add bus functionality to base PRCM nodes Tony Lindgren
2017-09-20 22:46 ` Tony Lindgren
2017-09-20 22:46 ` [PATCH 07/10] bus: ti-sysc: Add minimal TI sysc interconnect target driver Tony Lindgren
2017-09-20 22:46 ` Tony Lindgren
[not found] ` <20170920224621.16236-1-tony-4v6yS6AI5VpBDgjK7y7TUQ@public.gmane.org>
2017-09-20 22:46 ` [PATCH 01/10] dt-bindings: bus: Minimal TI sysc interconnect target module binding Tony Lindgren
2017-09-20 22:46 ` Tony Lindgren
[not found] ` <20170920224621.16236-2-tony-4v6yS6AI5VpBDgjK7y7TUQ@public.gmane.org>
2017-09-25 6:35 ` Matthijs van Duin
2017-09-25 6:35 ` Matthijs van Duin
[not found] ` <20170925063545.nn3gr5drea6o2g6m-2pNSKKP3PSK44ywRPIzf9A@public.gmane.org>
2017-09-25 14:25 ` Tony Lindgren
2017-09-25 14:25 ` Tony Lindgren
[not found] ` <20170925142520.GE4394-4v6yS6AI5VpBDgjK7y7TUQ@public.gmane.org>
2017-09-25 17:21 ` Matthijs van Duin
2017-09-25 17:21 ` Matthijs van Duin
[not found] ` <20170925172120.xu6k3leg4ac6mjya-2pNSKKP3PSK44ywRPIzf9A@public.gmane.org>
2017-09-25 17:44 ` Tony Lindgren
2017-09-25 17:44 ` Tony Lindgren
[not found] ` <20170925174413.GH4394-4v6yS6AI5VpBDgjK7y7TUQ@public.gmane.org>
2017-09-27 9:56 ` Matthijs van Duin
2017-09-27 9:56 ` Matthijs van Duin
[not found] ` <20170927095646.fi4l7jbbvrubfe25-2pNSKKP3PSK44ywRPIzf9A@public.gmane.org>
2017-09-29 17:51 ` Tony Lindgren
2017-09-29 17:51 ` Tony Lindgren
2017-09-25 7:03 ` Matthijs van Duin
2017-09-25 7:03 ` Matthijs van Duin
[not found] ` <20170925070345.2uraikhswru77rm4-2pNSKKP3PSK44ywRPIzf9A@public.gmane.org>
2017-09-25 14:37 ` Tony Lindgren
2017-09-25 14:37 ` Tony Lindgren
2017-09-20 22:46 ` Tony Lindgren [this message]
2017-09-20 22:46 ` [PATCH 04/10] ARM: dts: omap4: add clkctrl nodes Tony Lindgren
2017-09-20 22:46 ` [PATCH 05/10] ARM: OMAP2+: Parse module IO range from dts for legacy "ti,hwmods" support Tony Lindgren
2017-09-20 22:46 ` [PATCH 05/10] ARM: OMAP2+: Parse module IO range from dts for legacy "ti, hwmods" support Tony Lindgren
2017-09-20 22:46 ` [PATCH 06/10] ARM: OMAP2+: Populate legacy resources for dma and smartreflex Tony Lindgren
2017-09-20 22:46 ` Tony Lindgren
2017-09-20 22:46 ` [PATCH 08/10] ARM: dts: Add nodes for missing omap4 interconnect target modules Tony Lindgren
2017-09-20 22:46 ` Tony Lindgren
[not found] ` <20170920224621.16236-9-tony-4v6yS6AI5VpBDgjK7y7TUQ@public.gmane.org>
2017-09-21 2:56 ` Matthijs van Duin
2017-09-21 2:56 ` Matthijs van Duin
[not found] ` <20170921025656.omeoippus7b4mmig-2pNSKKP3PSK44ywRPIzf9A@public.gmane.org>
2017-09-21 14:27 ` Tony Lindgren
2017-09-21 14:27 ` Tony Lindgren
2017-09-20 22:46 ` [PATCH 09/10] ARM: dts: Configure SmartReflex only to idle the interconnect target module Tony Lindgren
2017-09-20 22:46 ` Tony Lindgren
2017-09-20 22:46 ` [PATCH 10/10] ARM: dts: Use ti-sysc module driver for omap4 musb Tony Lindgren
2017-09-20 22:46 ` Tony Lindgren
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20170920224621.16236-5-tony@atomide.com \
--to=tony-4v6ys6ai5vpbdgjk7y7tuq@public.gmane.org \
--cc=bcousson-rdvid1DuHRBWk0Htik3J/w@public.gmane.org \
--cc=devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org \
--cc=linux-omap-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=t-kristo-l0cyMroinI0@public.gmane.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.