[PATCH v2 01/12] ARM: dts: imx51-ts4800: Fix syscon and touschscreen nodes

[PATCH v2 01/12] ARM: dts: imx51-ts4800: Fix syscon and touschscreen nodes

[Fabio Estevam]

From: Fabio Estevam <fabio.estevam@nxp.com>

The syscon node has an incorrect notation for its unit address and the
wdt node has an unneeded unit address.

Fix them so that the following build warnings with W=1 are gone:

arch/arm/boot/dts/imx51-ts4800.dtb: Warning (unit_address_vs_reg): Node /soc/aips at 80000000/weim at 83fda000/fpga at 0/syscon at b0010000/wdt at e has a unit name, but no reg property
arch/arm/boot/dts/imx51-ts4800.dtb: Warning (unit_address_vs_reg): Node /soc/aips at 80000000/weim at 83fda000/fpga at 0/touchscreen has a reg or ranges property, but no unit name
arch/arm/boot/dts/imx51-ts4800.dtb: Warning (simple_bus_reg): Node /soc/aips at 80000000/weim at 83fda000/fpga at 0/syscon at b0010000 simple-bus unit address format error, expected "10000"
arch/arm/boot/dts/imx51-ts4800.dtb: Warning (simple_bus_reg): Node /soc/aips at 80000000/weim at 83fda000/fpga at 0/touchscreen simple-bus unit address format error, expected "12000"

Cc: Damien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
---
Changes since v1:
- Removed 'Node /memory has a reg or ranges property, but no unit name' error

 arch/arm/boot/dts/imx51-ts4800.dts | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/imx51-ts4800.dts b/arch/arm/boot/dts/imx51-ts4800.dts
index 564233e..f59b02b 100644
--- a/arch/arm/boot/dts/imx51-ts4800.dts
+++ b/arch/arm/boot/dts/imx51-ts4800.dts
@@ -149,18 +149,18 @@
 		#size-cells = <1>;
 		ranges = <0 0 0 0x1d000>;
 
-		syscon: syscon at b0010000 {
+		syscon: syscon at 10000 {
 			compatible = "syscon", "simple-mfd";
 			reg = <0x10000 0x3d>;
 			reg-io-width = <2>;
 
-			wdt at e {
+			wdt {
 				compatible = "technologic,ts4800-wdt";
 				syscon = <&syscon 0xe>;
 			};
 		};
 
-		touchscreen {
+		touchscreen at 12000 {
 			compatible = "technologic,ts4800-ts";
 			reg = <0x12000 0x1000>;
 			syscon = <&syscon 0x10 6>;
-- 
2.7.4

[PATCH v2 02/12] ARM: dts: imx51-zii-rdu1: Add the unit addresses in sysled

[Fabio Estevam]

From: Fabio Estevam <fabio.estevam@nxp.com>

As described at Documentation/devicetree/bindings/mfd/mc13xxx.txt the
reg property is mandatory, so add the corresponding unit address in
order to fix the following build warnings with W=1:

arch/arm/boot/dts/imx51-zii-rdu1.dtb: Warning (unit_address_vs_reg): Node /soc/aips at 70000000/spba at 70000000/ecspi at 70010000/pmic at 0/leds/sysled0 has a reg or ranges property, but no unit name
arch/arm/boot/dts/imx51-zii-rdu1.dtb: Warning (unit_address_vs_reg): Node /soc/aips at 70000000/spba at 70000000/ecspi at 70010000/pmic at 0/leds/sysled1 has a reg or ranges property, but no unit name

Cc: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
---
Changes since v1:
- Removed 'Node /memory has a reg or ranges property, but no unit name' error

 arch/arm/boot/dts/imx51-zii-rdu1.dts | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/imx51-zii-rdu1.dts b/arch/arm/boot/dts/imx51-zii-rdu1.dts
index f9fdb7c..70fdcdd 100644
--- a/arch/arm/boot/dts/imx51-zii-rdu1.dts
+++ b/arch/arm/boot/dts/imx51-zii-rdu1.dts
@@ -428,13 +428,13 @@
 			#size-cells = <0>;
 			led-control = <0x0 0x0 0x3f83f8 0x0>;
 
-			sysled0 {
+			sysled0 at 3 {
 				reg = <3>;
 				label = "system:green:status";
 				linux,default-trigger = "default-on";
 			};
 
-			sysled1 {
+			sysled1 at 4 {
 				reg = <4>;
 				label = "system:green:act";
 				linux,default-trigger = "heartbeat";
-- 
2.7.4

[PATCH v2 02/12] ARM: dts: imx51-zii-rdu1: Add the unit addresses in sysled

[Lucas Stach]

Am Montag, den 04.12.2017, 10:20 -0200 schrieb Fabio Estevam:
> From: Fabio Estevam <fabio.estevam@nxp.com>
> 
> As described at Documentation/devicetree/bindings/mfd/mc13xxx.txt the
> reg property is mandatory, so add the corresponding unit address in
> order to fix the following build warnings with W=1:
> 
> arch/arm/boot/dts/imx51-zii-rdu1.dtb: Warning (unit_address_vs_reg):
> Node /soc/aips at 70000000/spba at 70000000/ecspi at 70010000/pmic at 0/leds/sysl
> ed0 has a reg or ranges property, but no unit name
> arch/arm/boot/dts/imx51-zii-rdu1.dtb: Warning (unit_address_vs_reg):
> Node /soc/aips at 70000000/spba at 70000000/ecspi at 70010000/pmic at 0/leds/sysl
> ed1 has a reg or ranges property, but no unit name
> 
> Cc: Lucas Stach <l.stach@pengutronix.de>
> Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>

Reviewed-by: Lucas Stach <l.stach@pengutronix.de>

> ---
> Changes since v1:
> - Removed 'Node /memory has a reg or ranges property, but no unit
> name' error
> 
> ?arch/arm/boot/dts/imx51-zii-rdu1.dts | 4 ++--
> ?1 file changed, 2 insertions(+), 2 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/imx51-zii-rdu1.dts
> b/arch/arm/boot/dts/imx51-zii-rdu1.dts
> index f9fdb7c..70fdcdd 100644
> --- a/arch/arm/boot/dts/imx51-zii-rdu1.dts
> +++ b/arch/arm/boot/dts/imx51-zii-rdu1.dts
> @@ -428,13 +428,13 @@
> ?			#size-cells = <0>;
> ?			led-control = <0x0 0x0 0x3f83f8 0x0>;
> ?
> -			sysled0 {
> +			sysled0 at 3 {
> ?				reg = <3>;
> ?				label = "system:green:status";
> ?				linux,default-trigger = "default-
> on";
> ?			};
> ?
> -			sysled1 {
> +			sysled1 at 4 {
> ?				reg = <4>;
> ?				label = "system:green:act";
> ?				linux,default-trigger = "heartbeat";

[PATCH v2 03/12] ARM: dts: imx53-m53: Remove unneeded reg property

[Fabio Estevam]

From: Fabio Estevam <fabio.estevam@nxp.com>

As described in
Documentation/devicetree/bindings/input/touchscreen/stmpe.txt
there is no 'reg' property under stmpe_touchscreen, so remove it
to fix the following build warning with W=1:

arch/arm/boot/dts/imx53-m53evk.dtb: Warning (unit_address_vs_reg): Node /soc/aips at 60000000/i2c at 63fc4000/stmpe610 at 41/stmpe_touchscreen has a reg or ranges property, but no unit name

Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
---
Changes since v1:
- None

 arch/arm/boot/dts/imx53-m53.dtsi | 1 -
 1 file changed, 1 deletion(-)

diff --git a/arch/arm/boot/dts/imx53-m53.dtsi b/arch/arm/boot/dts/imx53-m53.dtsi
index ec390aa5..7ce69c6 100644
--- a/arch/arm/boot/dts/imx53-m53.dtsi
+++ b/arch/arm/boot/dts/imx53-m53.dtsi
@@ -64,7 +64,6 @@
 
 		stmpe_touchscreen {
 			compatible = "st,stmpe-ts";
-			reg = <0>;
 			st,sample-time = <4>;
 			st,mod-12b = <1>;
 			st,ref-sel = <0>;
-- 
2.7.4

[PATCH v2 04/12] ARM: dts: imx53-tx53-x03x: Move display node out of 'soc'

[Fabio Estevam]

From: Fabio Estevam <fabio.estevam@nxp.com>

Move disp0 node from soc node to root node.

disp0 node does not have any register properties and thus
shouldn't be placed on the bus.

This fixes the following build warnings with W=1:

arch/arm/boot/dts/imx53-tx53-x03x.dtb: Warning (simple_bus_reg): Node /soc/disp0 missing or empty reg/ranges property

Cc: Lothar Wa?mann <LW@KARO-electronics.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Lothar Wa?mann <LW@KARO-electronics.de>
---
Changes since v1:
- None

 arch/arm/boot/dts/imx53-tx53-x03x.dts | 232 +++++++++++++++++-----------------
 1 file changed, 115 insertions(+), 117 deletions(-)

diff --git a/arch/arm/boot/dts/imx53-tx53-x03x.dts b/arch/arm/boot/dts/imx53-tx53-x03x.dts
index 7eb53e4..fe15c95 100644
--- a/arch/arm/boot/dts/imx53-tx53-x03x.dts
+++ b/arch/arm/boot/dts/imx53-tx53-x03x.dts
@@ -53,132 +53,130 @@
 		display = &display;
 	};
 
-	soc {
-		display: disp0 {
-			compatible = "fsl,imx-parallel-display";
-			interface-pix-fmt = "rgb24";
-			pinctrl-names = "default";
-			pinctrl-0 = <&pinctrl_rgb24_vga1>;
-			status = "okay";
+	display: disp0 {
+		compatible = "fsl,imx-parallel-display";
+		interface-pix-fmt = "rgb24";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_rgb24_vga1>;
+		status = "okay";
 
-			port {
-				display0_in: endpoint {
-					remote-endpoint = <&ipu_di0_disp0>;
-				};
+		port {
+			display0_in: endpoint {
+				remote-endpoint = <&ipu_di0_disp0>;
 			};
+		};
 
-			display-timings {
-				VGA {
-					clock-frequency = <25200000>;
-					hactive = <640>;
-					vactive = <480>;
-					hback-porch = <48>;
-					hsync-len = <96>;
-					hfront-porch = <16>;
-					vback-porch = <31>;
-					vsync-len = <2>;
-					vfront-porch = <12>;
-					hsync-active = <0>;
-					vsync-active = <0>;
-					de-active = <1>;
-					pixelclk-active = <0>;
-				};
+		display-timings {
+			VGA {
+				clock-frequency = <25200000>;
+				hactive = <640>;
+				vactive = <480>;
+				hback-porch = <48>;
+				hsync-len = <96>;
+				hfront-porch = <16>;
+				vback-porch = <31>;
+				vsync-len = <2>;
+				vfront-porch = <12>;
+				hsync-active = <0>;
+				vsync-active = <0>;
+				de-active = <1>;
+				pixelclk-active = <0>;
+			};
 
-				ETV570 {
-					clock-frequency = <25200000>;
-					hactive = <640>;
-					vactive = <480>;
-					hback-porch = <114>;
-					hsync-len = <30>;
-					hfront-porch = <16>;
-					vback-porch = <32>;
-					vsync-len = <3>;
-					vfront-porch = <10>;
-					hsync-active = <0>;
-					vsync-active = <0>;
-					de-active = <1>;
-					pixelclk-active = <0>;
-				};
+			ETV570 {
+				clock-frequency = <25200000>;
+				hactive = <640>;
+				vactive = <480>;
+				hback-porch = <114>;
+				hsync-len = <30>;
+				hfront-porch = <16>;
+				vback-porch = <32>;
+				vsync-len = <3>;
+				vfront-porch = <10>;
+				hsync-active = <0>;
+				vsync-active = <0>;
+				de-active = <1>;
+				pixelclk-active = <0>;
+			};
 
-				ET0350 {
-					clock-frequency = <6413760>;
-					hactive = <320>;
-					vactive = <240>;
-					hback-porch = <34>;
-					hsync-len = <34>;
-					hfront-porch = <20>;
-					vback-porch = <15>;
-					vsync-len = <3>;
-					vfront-porch = <4>;
-					hsync-active = <0>;
-					vsync-active = <0>;
-					de-active = <1>;
-					pixelclk-active = <0>;
-				};
+			ET0350 {
+				clock-frequency = <6413760>;
+				hactive = <320>;
+				vactive = <240>;
+				hback-porch = <34>;
+				hsync-len = <34>;
+				hfront-porch = <20>;
+				vback-porch = <15>;
+				vsync-len = <3>;
+				vfront-porch = <4>;
+				hsync-active = <0>;
+				vsync-active = <0>;
+				de-active = <1>;
+				pixelclk-active = <0>;
+			};
 
-				ET0430 {
-					clock-frequency = <9009000>;
-					hactive = <480>;
-					vactive = <272>;
-					hback-porch = <2>;
-					hsync-len = <41>;
-					hfront-porch = <2>;
-					vback-porch = <2>;
-					vsync-len = <10>;
-					vfront-porch = <2>;
-					hsync-active = <0>;
-					vsync-active = <0>;
-					de-active = <1>;
-					pixelclk-active = <1>;
-				};
+			ET0430 {
+				clock-frequency = <9009000>;
+				hactive = <480>;
+				vactive = <272>;
+				hback-porch = <2>;
+				hsync-len = <41>;
+				hfront-porch = <2>;
+				vback-porch = <2>;
+				vsync-len = <10>;
+				vfront-porch = <2>;
+				hsync-active = <0>;
+				vsync-active = <0>;
+				de-active = <1>;
+				pixelclk-active = <1>;
+			};
 
-				ET0500 {
-					clock-frequency = <33264000>;
-					hactive = <800>;
-					vactive = <480>;
-					hback-porch = <88>;
-					hsync-len = <128>;
-					hfront-porch = <40>;
-					vback-porch = <33>;
-					vsync-len = <2>;
-					vfront-porch = <10>;
-					hsync-active = <0>;
-					vsync-active = <0>;
-					de-active = <1>;
-					pixelclk-active = <0>;
-				};
+			ET0500 {
+				clock-frequency = <33264000>;
+				hactive = <800>;
+				vactive = <480>;
+				hback-porch = <88>;
+				hsync-len = <128>;
+				hfront-porch = <40>;
+				vback-porch = <33>;
+				vsync-len = <2>;
+				vfront-porch = <10>;
+				hsync-active = <0>;
+				vsync-active = <0>;
+				de-active = <1>;
+				pixelclk-active = <0>;
+			};
 
-				ET0700 { /* same as ET0500 */
-					clock-frequency = <33264000>;
-					hactive = <800>;
-					vactive = <480>;
-					hback-porch = <88>;
-					hsync-len = <128>;
-					hfront-porch = <40>;
-					vback-porch = <33>;
-					vsync-len = <2>;
-					vfront-porch = <10>;
-					hsync-active = <0>;
-					vsync-active = <0>;
-					de-active = <1>;
-					pixelclk-active = <0>;
-				};
+			ET0700 { /* same as ET0500 */
+				clock-frequency = <33264000>;
+				hactive = <800>;
+				vactive = <480>;
+				hback-porch = <88>;
+				hsync-len = <128>;
+				hfront-porch = <40>;
+				vback-porch = <33>;
+				vsync-len = <2>;
+				vfront-porch = <10>;
+				hsync-active = <0>;
+				vsync-active = <0>;
+				de-active = <1>;
+				pixelclk-active = <0>;
+			};
 
-				ETQ570 {
-					clock-frequency = <6596040>;
-					hactive = <320>;
-					vactive = <240>;
-					hback-porch = <38>;
-					hsync-len = <30>;
-					hfront-porch = <30>;
-					vback-porch = <16>;
-					vsync-len = <3>;
-					vfront-porch = <4>;
-					hsync-active = <0>;
-					vsync-active = <0>;
-					de-active = <1>;
-					pixelclk-active = <0>;
-				};
+			ETQ570 {
+				clock-frequency = <6596040>;
+				hactive = <320>;
+				vactive = <240>;
+				hback-porch = <38>;
+				hsync-len = <30>;
+				hfront-porch = <30>;
+				vback-porch = <16>;
+				vsync-len = <3>;
+				vfront-porch = <4>;
+				hsync-active = <0>;
+				vsync-active = <0>;
+				de-active = <1>;
+				pixelclk-active = <0>;
 			};
 		};
 	};
-- 
2.7.4

[PATCH v2 05/12] ARM: dts: imx6qdl-apf6dev: Move regulators out of simple-bus

[Fabio Estevam]

From: Fabio Estevam <fabio.estevam@nxp.com>

It is not recommended to place regulator nodes inside simple-bus, so
move them out in order to fix the following build warnings with W=1:

arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (simple_bus_reg): Node /regulators/3p3v missing or empty reg/ranges property
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (simple_bus_reg): Node /regulators/usb-h1-vbus missing or empty reg/ranges property
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (simple_bus_reg): Node /regulators/usb-otg-vbus missing or empty reg/ranges property

Cc: S?bastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
---
Changes since v1:
- None

 arch/arm/boot/dts/imx6qdl-apf6dev.dtsi | 44 ++++++++++++++++------------------
 1 file changed, 20 insertions(+), 24 deletions(-)

diff --git a/arch/arm/boot/dts/imx6qdl-apf6dev.dtsi b/arch/arm/boot/dts/imx6qdl-apf6dev.dtsi
index 829a479..a61dd1a 100644
--- a/arch/arm/boot/dts/imx6qdl-apf6dev.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-apf6dev.dtsi
@@ -111,32 +111,28 @@
 		};
 	};
 
-	regulators {
-		compatible = "simple-bus";
-
-		reg_3p3v: 3p3v {
-			compatible = "regulator-fixed";
-			regulator-name = "3P3V";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
 
-		reg_usbh1_vbus: usb-h1-vbus {
-			compatible = "regulator-fixed";
-			regulator-name = "usb_h1_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			regulator-always-on;
-		};
+	reg_usbh1_vbus: regulator-usb-h1-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_h1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
 
-		reg_usb_otg_vbus: usb-otg-vbus {
-			compatible = "regulator-fixed";
-			regulator-name = "usb_otg_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			regulator-always-on;
-		};
+	reg_usb_otg_vbus: regulator-usb-otg-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
 	};
 
 	sound {
-- 
2.7.4

[PATCH v2 06/12] ARM: dts: imx6qdl-aristainetos: Move regulators out of simple-bus

[Fabio Estevam]

From: Fabio Estevam <fabio.estevam@nxp.com>

It is not recommended to place regulator nodes inside simple-bus, so
move them out in order to fix the following build warnings with W=1:

arch/arm/boot/dts/imx6dl-aristainetos_4.dtb: Warning (unit_address_vs_reg): Node /regulators/regulator at 0 has a unit name, but no reg property
arch/arm/boot/dts/imx6dl-aristainetos_4.dtb: Warning (unit_address_vs_reg): Node /regulators/regulator at 1 has a unit name, but no reg property
arch/arm/boot/dts/imx6dl-aristainetos_4.dtb: Warning (unit_address_vs_reg): Node /regulators/regulator at 2 has a unit name, but no reg property
arch/arm/boot/dts/imx6dl-aristainetos_4.dtb: Warning (unit_address_vs_reg): Node /regulators/regulator at 3 has a unit name, but no reg property

Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
---
Changes since v1:
- Removed 'Node /memory has a reg or ranges property, but no unit name' error

 arch/arm/boot/dts/imx6qdl-aristainetos.dtsi  | 73 +++++++++++++-------------
 arch/arm/boot/dts/imx6qdl-aristainetos2.dtsi | 76 +++++++++++++---------------
 2 files changed, 70 insertions(+), 79 deletions(-)

diff --git a/arch/arm/boot/dts/imx6qdl-aristainetos.dtsi b/arch/arm/boot/dts/imx6qdl-aristainetos.dtsi
index 7d64075..ee4d0f8 100644
--- a/arch/arm/boot/dts/imx6qdl-aristainetos.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-aristainetos.dtsi
@@ -12,48 +12,43 @@
 #include <dt-bindings/gpio/gpio.h>
 
 / {
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_2p5v: regulator at 0 {
-			compatible = "regulator-fixed";
-			regulator-name = "2P5V";
-			regulator-min-microvolt = <2500000>;
-			regulator-max-microvolt = <2500000>;
-			regulator-always-on;
-		};
 
-		reg_3p3v: regulator at 1 {
-			compatible = "regulator-fixed";
-			regulator-name = "3P3V";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
+	reg_2p5v: regulator-2p5v {
+		compatible = "regulator-fixed";
+		regulator-name = "2P5V";
+		regulator-min-microvolt = <2500000>;
+		regulator-max-microvolt = <2500000>;
+		regulator-always-on;
+	};
 
-		reg_usbh1_vbus: regulator at 2 {
-			compatible = "regulator-fixed";
-			enable-active-high;
-			gpio = <&gpio3 31 GPIO_ACTIVE_HIGH>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&pinctrl_aristainetos_usbh1_vbus>;
-			regulator-name = "usb_h1_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-		};
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
 
-		reg_usbotg_vbus: regulator at 3 {
-			compatible = "regulator-fixed";
-			enable-active-high;
-			gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&pinctrl_aristainetos_usbotg_vbus>;
-			regulator-name = "usb_otg_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-		};
+	reg_usbh1_vbus: regulator-usbh1-vbus {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio3 31 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_aristainetos_usbh1_vbus>;
+		regulator-name = "usb_h1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_usbotg_vbus: regulator-usbotg-vbus {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_aristainetos_usbotg_vbus>;
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
 	};
 };
 
diff --git a/arch/arm/boot/dts/imx6qdl-aristainetos2.dtsi b/arch/arm/boot/dts/imx6qdl-aristainetos2.dtsi
index 1b18728..3767508 100644
--- a/arch/arm/boot/dts/imx6qdl-aristainetos2.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-aristainetos2.dtsi
@@ -52,46 +52,42 @@
 		enable-gpios = <&gpio6 31 GPIO_ACTIVE_HIGH>;
 	};
 
-	regulators {
-		compatible = "simple-bus";
-
-		reg_2p5v: 2p5v {
-			compatible = "regulator-fixed";
-			regulator-name = "2P5V";
-			regulator-min-microvolt = <2500000>;
-			regulator-max-microvolt = <2500000>;
-			regulator-always-on;
-		};
-
-		reg_3p3v: 3p3v {
-			compatible = "regulator-fixed";
-			regulator-name = "3P3V";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
-
-		reg_usbh1_vbus: usb-h1-vbus {
-			compatible = "regulator-fixed";
-			enable-active-high;
-			gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&pinctrl_aristainetos2_usbh1_vbus>;
-			regulator-name = "usb_h1_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-		};
-
-		reg_usbotg_vbus: usb-otg-vbus {
-			compatible = "regulator-fixed";
-			enable-active-high;
-			gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&pinctrl_aristainetos2_usbotg_vbus>;
-			regulator-name = "usb_otg_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-		};
+	reg_2p5v: regulator-2p5v {
+		compatible = "regulator-fixed";
+		regulator-name = "2P5V";
+		regulator-min-microvolt = <2500000>;
+		regulator-max-microvolt = <2500000>;
+		regulator-always-on;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	reg_usbh1_vbus: regulator-usbh1-vbus {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_aristainetos2_usbh1_vbus>;
+		regulator-name = "usb_h1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_usbotg_vbus: regulator-usbotg-vbus {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_aristainetos2_usbotg_vbus>;
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
 	};
 };
 
-- 
2.7.4

[PATCH v2 07/12] ARM: dts: imx6qdl-aristainetos: Move display node out of 'soc'

[Fabio Estevam]

From: Fabio Estevam <fabio.estevam@nxp.com>

Move disp0 node from soc node to root node.

disp0 node does not have any register properties and thus
shouldn't be placed on the bus.

This fixes the following build warnings with W=1:

arch/arm/boot/dts/imx6dl-aristainetos_4.dtb: Warning (simple_bus_reg): Node /soc/disp0 missing or empty reg/ranges property

Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
---
Changes since v1:
- None

 arch/arm/boot/dts/imx6dl-aristainetos_4.dts | 50 ++++++++++++++---------------
 arch/arm/boot/dts/imx6dl-aristainetos_7.dts | 48 +++++++++++++--------------
 2 files changed, 47 insertions(+), 51 deletions(-)

diff --git a/arch/arm/boot/dts/imx6dl-aristainetos_4.dts b/arch/arm/boot/dts/imx6dl-aristainetos_4.dts
index cc418ce..3c9f4af 100644
--- a/arch/arm/boot/dts/imx6dl-aristainetos_4.dts
+++ b/arch/arm/boot/dts/imx6dl-aristainetos_4.dts
@@ -31,35 +31,33 @@
 		reg = <0x10000000 0x40000000>;
 	};
 
-	soc {
-		display0: disp0 {
-			compatible = "fsl,imx-parallel-display";
-			interface-pix-fmt = "rgb24";
-			pinctrl-names = "default";
-			pinctrl-0 = <&pinctrl_ipu_disp>;
-			status = "okay";
+	display0: disp0 {
+		compatible = "fsl,imx-parallel-display";
+		interface-pix-fmt = "rgb24";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ipu_disp>;
+		status = "okay";
 
-			display-timings {
-				480x800p60 {
-					native-mode;
-					clock-frequency = <30000000>;
-					hactive = <480>;
-					vactive = <800>;
-					hfront-porch = <59>;
-					hback-porch = <10>;
-					hsync-len = <10>;
-					vback-porch = <15>;
-					vfront-porch = <15>;
-					vsync-len = <15>;
-					hsync-active = <1>;
-					vsync-active = <1>;
-				};
+		display-timings {
+			480x800p60 {
+				native-mode;
+				clock-frequency = <30000000>;
+				hactive = <480>;
+				vactive = <800>;
+				hfront-porch = <59>;
+				hback-porch = <10>;
+				hsync-len = <10>;
+				vback-porch = <15>;
+				vfront-porch = <15>;
+				vsync-len = <15>;
+				hsync-active = <1>;
+				vsync-active = <1>;
 			};
+		};
 
-			port {
-				display0_in: endpoint {
-					remote-endpoint = <&ipu1_di0_disp0>;
-				};
+		port {
+			display0_in: endpoint {
+				remote-endpoint = <&ipu1_di0_disp0>;
 			};
 		};
 	};
diff --git a/arch/arm/boot/dts/imx6dl-aristainetos_7.dts b/arch/arm/boot/dts/imx6dl-aristainetos_7.dts
index 126ff96..96cd835 100644
--- a/arch/arm/boot/dts/imx6dl-aristainetos_7.dts
+++ b/arch/arm/boot/dts/imx6dl-aristainetos_7.dts
@@ -20,34 +20,32 @@
 		reg = <0x10000000 0x40000000>;
 	};
 
-	soc {
-		display0: disp0 {
-			compatible = "fsl,imx-parallel-display";
-			interface-pix-fmt = "rgb24";
-			pinctrl-names = "default";
-			pinctrl-0 = <&pinctrl_ipu_disp>;
-			status = "okay";
+	display0: disp0 {
+		compatible = "fsl,imx-parallel-display";
+		interface-pix-fmt = "rgb24";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ipu_disp>;
+		status = "okay";
 
-			display-timings {
-				800x480p60 {
-					native-mode;
-					clock-frequency = <33246000>;
-					hactive = <800>;
-					vactive = <480>;
-					hfront-porch = <88>;
-					hback-porch = <88>;
-					hsync-len = <80>;
-					vback-porch = <10>;
-					vfront-porch = <10>;
-					vsync-len = <25>;
-					vsync-active = <1>;
-				};
+		display-timings {
+			800x480p60 {
+				native-mode;
+				clock-frequency = <33246000>;
+				hactive = <800>;
+				vactive = <480>;
+				hfront-porch = <88>;
+				hback-porch = <88>;
+				hsync-len = <80>;
+				vback-porch = <10>;
+				vfront-porch = <10>;
+				vsync-len = <25>;
+				vsync-active = <1>;
 			};
+		};
 
-			port {
-				display0_in: endpoint {
-					remote-endpoint = <&ipu1_di0_disp0>;
-				};
+		port {
+			display0_in: endpoint {
+				remote-endpoint = <&ipu1_di0_disp0>;
 			};
 		};
 	};
-- 
2.7.4

[PATCH v2 08/12] ARM: dts: imx6qdl-apalis: Remove unneeded reg property

[Fabio Estevam]

From: Fabio Estevam <fabio.estevam@nxp.com>

As described in
Documentation/devicetree/bindings/input/touchscreen/stmpe.txt
there is no 'reg' property under stmpe_touchscreen, so remove it
to fix the following build warning with W=1:

arch/arm/boot/dts/imx6q-apalis-eval.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus at 2100000/i2c at 21a4000/stmpe811 at 41/stmpe_touchscreen has a reg or ranges property, but no unit name

Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
---
Changes since v1:
- None

 arch/arm/boot/dts/imx6qdl-apalis.dtsi | 1 -
 1 file changed, 1 deletion(-)

diff --git a/arch/arm/boot/dts/imx6qdl-apalis.dtsi b/arch/arm/boot/dts/imx6qdl-apalis.dtsi
index e80fdca..4e776e0 100644
--- a/arch/arm/boot/dts/imx6qdl-apalis.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-apalis.dtsi
@@ -338,7 +338,6 @@
 
 		stmpe_touchscreen {
 			compatible = "st,stmpe-ts";
-			reg = <0>;
 			/* 3.25 MHz ADC clock speed */
 			st,adc-freq = <1>;
 			/* 8 sample average control */
-- 
2.7.4

[PATCH v2 09/12] ARM: dts: imx6qdl-colibri: Remove unneeded reg property

[Fabio Estevam]

From: Fabio Estevam <fabio.estevam@nxp.com>

As described in
Documentation/devicetree/bindings/input/touchscreen/stmpe.txt
there is no 'reg' property under stmpe_touchscreen, so remove it
to fix the following build warning with W=1:

arch/arm/boot/dts/imx6dl-colibri-eval-v3.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus at 2100000/i2c at 21a4000/stmpe811 at 41/stmpe_touchscreen has a reg or ranges property, but no unit name

Cc: Sanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
---
Changes since v1:
- None

 arch/arm/boot/dts/imx6qdl-colibri.dtsi | 1 -
 1 file changed, 1 deletion(-)

diff --git a/arch/arm/boot/dts/imx6qdl-colibri.dtsi b/arch/arm/boot/dts/imx6qdl-colibri.dtsi
index fc66bbf..e4eb300 100644
--- a/arch/arm/boot/dts/imx6qdl-colibri.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-colibri.dtsi
@@ -274,7 +274,6 @@
 
 		stmpe_touchscreen {
 			compatible = "st,stmpe-ts";
-			reg = <0>;
 			/* 3.25 MHz ADC clock speed */
 			st,adc-freq = <1>;
 			/* 8 sample average control */
-- 
2.7.4

[PATCH v2 10/12] ARM: dts: imx6q-h100: Remove unneeded unit address

[Fabio Estevam]

From: Fabio Estevam <fabio.estevam@nxp.com>

Remove the unneeded unit address for the port nodes in order to fix
the following build warnings with W=1:

arch/arm/boot/dts/imx6q-h100.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus at 2100000/i2c at 21a0000/tc358743 at f/port at 0 has a unit name, but no reg property
arch/arm/boot/dts/imx6q-h100.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus at 2100000/mipi at 21dc000/port at 0 has a unit name, but no reg property

Cc: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
---
Changes since v1:
- None

 arch/arm/boot/dts/imx6q-h100.dts | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/imx6q-h100.dts b/arch/arm/boot/dts/imx6q-h100.dts
index 743c11f..cc1ce46 100644
--- a/arch/arm/boot/dts/imx6q-h100.dts
+++ b/arch/arm/boot/dts/imx6q-h100.dts
@@ -205,7 +205,7 @@
 		reset-gpios = <&gpio6 15 GPIO_ACTIVE_LOW>;
 		/* IRQ has a wrong pull resistor which renders it useless  */
 
-		port at 0 {
+		port {
 			tc358743_out: endpoint {
 				remote-endpoint = <&mipi_csi2_in>;
 				data-lanes = <1 2 3 4>;
@@ -348,7 +348,7 @@
 &mipi_csi {
 	status = "okay";
 
-	port at 0 {
+	port {
 		mipi_csi2_in: endpoint {
 			remote-endpoint = <&tc358743_out>;
 			data-lanes = <1 2 3 4>;
-- 
2.7.4

[PATCH v2 10/12] ARM: dts: imx6q-h100: Remove unneeded unit address

[Lucas Stach]

Am Montag, den 04.12.2017, 10:20 -0200 schrieb Fabio Estevam:
> From: Fabio Estevam <fabio.estevam@nxp.com>
> 
> Remove the unneeded unit address for the port nodes in order to fix
> the following build warnings with W=1:
> 
> arch/arm/boot/dts/imx6q-h100.dtb: Warning (unit_address_vs_reg): Node
> /soc/aips-bus at 2100000/i2c at 21a0000/tc358743 at f/port at 0 has a unit name,
> but no reg property
> arch/arm/boot/dts/imx6q-h100.dtb: Warning (unit_address_vs_reg): Node
> /soc/aips-bus at 2100000/mipi at 21dc000/port at 0 has a unit name, but no reg
> property
> 
> Cc: Lucas Stach <l.stach@pengutronix.de>
> Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>

Reviewed-by: Lucas Stach <l.stach@pengutronix.de>

> ---
> Changes since v1:
> - None
> 
> ?arch/arm/boot/dts/imx6q-h100.dts | 4 ++--
> ?1 file changed, 2 insertions(+), 2 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/imx6q-h100.dts
> b/arch/arm/boot/dts/imx6q-h100.dts
> index 743c11f..cc1ce46 100644
> --- a/arch/arm/boot/dts/imx6q-h100.dts
> +++ b/arch/arm/boot/dts/imx6q-h100.dts
> @@ -205,7 +205,7 @@
> ?		reset-gpios = <&gpio6 15 GPIO_ACTIVE_LOW>;
> ?		/* IRQ has a wrong pull resistor which renders it
> useless??*/
> ?
> -		port at 0 {
> +		port {
> ?			tc358743_out: endpoint {
> ?				remote-endpoint = <&mipi_csi2_in>;
> ?				data-lanes = <1 2 3 4>;
> @@ -348,7 +348,7 @@
> ?&mipi_csi {
> ?	status = "okay";
> ?
> -	port at 0 {
> +	port {
> ?		mipi_csi2_in: endpoint {
> ?			remote-endpoint = <&tc358743_out>;
> ?			data-lanes = <1 2 3 4>;

[PATCH v2 11/12] ARM: dts: imx6qdl-nitrogen6_max: Remove unneeded unit address

[Fabio Estevam]

From: Fabio Estevam <fabio.estevam@nxp.com>

Remove the unneeded unit address for the i2cmux nodes in order to fix
the following build warnings with W=1:

arch/arm/boot/dts/imx6q-nitrogen6_max.dtb: Warning (unit_address_vs_reg): Node /i2cmux at 2 has a unit name, but no reg property
arch/arm/boot/dts/imx6q-nitrogen6_max.dtb: Warning (unit_address_vs_reg): Node /i2cmux at 3 has a unit name, but no reg property

While at it, rename the i2cmux nodes and subnodes to make it clearer to which
i2c controller the mux belongs to.

Cc: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
---
Changes since v1:
- Rename the i2cmux nodes and subnodes for making it clear (Gary).

 arch/arm/boot/dts/imx6qdl-nitrogen6_max.dtsi | 10 +++++-----
 1 file changed, 5 insertions(+), 5 deletions(-)

diff --git a/arch/arm/boot/dts/imx6qdl-nitrogen6_max.dtsi b/arch/arm/boot/dts/imx6qdl-nitrogen6_max.dtsi
index 3a77f0f..fd05f7c 100644
--- a/arch/arm/boot/dts/imx6qdl-nitrogen6_max.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-nitrogen6_max.dtsi
@@ -172,7 +172,7 @@
 		};
 	};
 
-	i2cmux at 2 {
+	i2c2mux {
 		compatible = "i2c-mux-gpio";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_i2c2mux>;
@@ -183,20 +183,20 @@
 		i2c-parent = <&i2c2>;
 		idle-state = <0>;
 
-		i2c2 at 1 {
+		i2c2mux at 1 {
 			reg = <1>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 		};
 
-		i2c2 at 2 {
+		i2c2mux at 2 {
 			reg = <2>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 		};
 	};
 
-	i2cmux at 3 {
+	i2c3mux {
 		compatible = "i2c-mux-gpio";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_i2c3mux>;
@@ -206,7 +206,7 @@
 		i2c-parent = <&i2c3>;
 		idle-state = <0>;
 
-		i2c3 at 1 {
+		i2c3mux at 1 {
 			reg = <1>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-- 
2.7.4

[PATCH v2 11/12] ARM: dts: imx6qdl-nitrogen6_max: Remove unneeded unit address

[Gary Bisson]

Hi Fabio,

On Mon, Dec 04, 2017 at 10:20:15AM -0200, Fabio Estevam wrote:
> From: Fabio Estevam <fabio.estevam@nxp.com>
> 
> Remove the unneeded unit address for the i2cmux nodes in order to fix
> the following build warnings with W=1:
> 
> arch/arm/boot/dts/imx6q-nitrogen6_max.dtb: Warning (unit_address_vs_reg): Node /i2cmux at 2 has a unit name, but no reg property
> arch/arm/boot/dts/imx6q-nitrogen6_max.dtb: Warning (unit_address_vs_reg): Node /i2cmux at 3 has a unit name, but no reg property
> 
> While at it, rename the i2cmux nodes and subnodes to make it clearer to which
> i2c controller the mux belongs to.
> 
> Cc: Gary Bisson <gary.bisson@boundarydevices.com>
> Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>

Reviewed-by: Gary Bisson <gary.bisson@boundarydevices.com>

Regards,
Gary

[PATCH v2 12/12] ARM: dts: imx6ul-14x14-evk: Move regulators out of simple-bus

[Fabio Estevam]

From: Fabio Estevam <fabio.estevam@nxp.com>

It is not recommended to place regulator nodes inside simple-bus, so
move them out in order to fix the following build warnings with W=1:

arch/arm/boot/dts/imx6ul-14x14-evk.dtb: Warning (simple_bus_reg): Node /regulators/sd1_regulator missing or empty reg/ranges property

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
---
Changes since v1:
- None

 arch/arm/boot/dts/imx6ul-14x14-evk.dts | 19 +++++++------------
 1 file changed, 7 insertions(+), 12 deletions(-)

diff --git a/arch/arm/boot/dts/imx6ul-14x14-evk.dts b/arch/arm/boot/dts/imx6ul-14x14-evk.dts
index e5d3ef8..18fdb08 100644
--- a/arch/arm/boot/dts/imx6ul-14x14-evk.dts
+++ b/arch/arm/boot/dts/imx6ul-14x14-evk.dts
@@ -30,19 +30,14 @@
 		status = "okay";
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		reg_sd1_vmmc: sd1_regulator {
-			compatible = "regulator-fixed";
-			regulator-name = "VSD_3V3";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&gpio1 9 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-		};
+	reg_sd1_vmmc: regulator-sd1-vmmc {
+		compatible = "regulator-fixed";
+		regulator-name = "VSD_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
 	};
 
 	sound {
-- 
2.7.4

[PATCH v2 01/12] ARM: dts: imx51-ts4800: Fix syscon and touschscreen nodes

[Shawn Guo]

On Mon, Dec 04, 2017 at 10:20:05AM -0200, Fabio Estevam wrote:
> From: Fabio Estevam <fabio.estevam@nxp.com>
> 
> The syscon node has an incorrect notation for its unit address and the
> wdt node has an unneeded unit address.
> 
> Fix them so that the following build warnings with W=1 are gone:
> 
> arch/arm/boot/dts/imx51-ts4800.dtb: Warning (unit_address_vs_reg): Node /soc/aips at 80000000/weim at 83fda000/fpga at 0/syscon at b0010000/wdt at e has a unit name, but no reg property
> arch/arm/boot/dts/imx51-ts4800.dtb: Warning (unit_address_vs_reg): Node /soc/aips at 80000000/weim at 83fda000/fpga at 0/touchscreen has a reg or ranges property, but no unit name
> arch/arm/boot/dts/imx51-ts4800.dtb: Warning (simple_bus_reg): Node /soc/aips at 80000000/weim at 83fda000/fpga at 0/syscon at b0010000 simple-bus unit address format error, expected "10000"
> arch/arm/boot/dts/imx51-ts4800.dtb: Warning (simple_bus_reg): Node /soc/aips at 80000000/weim at 83fda000/fpga at 0/touchscreen simple-bus unit address format error, expected "12000"
> 
> Cc: Damien Riegel <damien.riegel@savoirfairelinux.com>
> Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
> Reviewed-by: Damien Riegel <damien.riegel@savoirfairelinux.com>

Applied all, thanks.