* [PATCH v3 1/3] ARM: dts: imx6sx-sdb: Convert from fbdev to drm bindings
@ 2017-12-06 15:15 ` Marco Franchi
0 siblings, 0 replies; 12+ messages in thread
From: Marco Franchi @ 2017-12-06 15:15 UTC (permalink / raw)
To: shawnguo
Cc: robh+dt, linux-arm-kernel, linux-kernel, devicetree, festevam,
marcofrk
It is preferred to use the panel compatible string rather than passing
the LCD timing in the device tree.
So pass the "sii,43wvf1g" compatible string, which describes the parallel
LCD.
Also pass the 'backlight' property as described in
Documentation/devicetree/bindings/display/panel/simple-panel.txt
Signed-off-by: Marco Franchi <marcofrk@gmail.com>
---
Changes since v2:
-none
arch/arm/boot/dts/imx6sx-sdb.dtsi | 48 +++++++++++++++++++--------------------
1 file changed, 24 insertions(+), 24 deletions(-)
diff --git a/arch/arm/boot/dts/imx6sx-sdb.dtsi b/arch/arm/boot/dts/imx6sx-sdb.dtsi
index d57a41c..d35aa85 100644
--- a/arch/arm/boot/dts/imx6sx-sdb.dtsi
+++ b/arch/arm/boot/dts/imx6sx-sdb.dtsi
@@ -24,7 +24,7 @@
reg = <0x80000000 0x40000000>;
};
- backlight {
+ backlight_display: backlight-display {
compatible = "pwm-backlight";
pwms = <&pwm3 0 5000000>;
brightness-levels = <0 4 8 16 32 64 128 255>;
@@ -129,6 +129,13 @@
enable-active-high;
};
+ reg_lcd_5v: regulator-lcd-5v {
+ compatible = "regulator-fixed";
+ regulator-name = "lcd-5v0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
sound {
compatible = "fsl,imx6sx-sdb-wm8962", "fsl,imx-audio-wm8962";
model = "wm8962-audio";
@@ -144,6 +151,19 @@
mux-int-port = <2>;
mux-ext-port = <6>;
};
+
+ panel {
+ compatible = "sii,43wvf1g";
+ backlight = <&backlight_display>;
+ dvdd-supply = <®_lcd_3v3>;
+ avdd-supply = <®_lcd_5v>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&display_out>;
+ };
+ };
+ };
};
&audmux {
@@ -221,31 +241,11 @@
&lcdif1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_lcd>;
- lcd-supply = <®_lcd_3v3>;
- display = <&display0>;
status = "okay";
- display0: display0 {
- bits-per-pixel = <16>;
- bus-width = <24>;
-
- display-timings {
- native-mode = <&timing0>;
- timing0: timing0 {
- clock-frequency = <33500000>;
- hactive = <800>;
- vactive = <480>;
- hback-porch = <89>;
- hfront-porch = <164>;
- vback-porch = <23>;
- vfront-porch = <10>;
- hsync-len = <10>;
- vsync-len = <10>;
- hsync-active = <0>;
- vsync-active = <0>;
- de-active = <1>;
- pixelclk-active = <0>;
- };
+ port {
+ display_out: endpoint {
+ remote-endpoint = <&panel_in>;
};
};
};
--
2.7.4
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH v3 1/3] ARM: dts: imx6sx-sdb: Convert from fbdev to drm bindings
@ 2017-12-06 15:15 ` Marco Franchi
0 siblings, 0 replies; 12+ messages in thread
From: Marco Franchi @ 2017-12-06 15:15 UTC (permalink / raw)
To: shawnguo-DgEjT+Ai2ygdnm+yROfE0A
Cc: robh+dt-DgEjT+Ai2ygdnm+yROfE0A,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
festevam-Re5JQEeQqe8AvxtiuMwx3w, marcofrk-Re5JQEeQqe8AvxtiuMwx3w
It is preferred to use the panel compatible string rather than passing
the LCD timing in the device tree.
So pass the "sii,43wvf1g" compatible string, which describes the parallel
LCD.
Also pass the 'backlight' property as described in
Documentation/devicetree/bindings/display/panel/simple-panel.txt
Signed-off-by: Marco Franchi <marcofrk-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
---
Changes since v2:
-none
arch/arm/boot/dts/imx6sx-sdb.dtsi | 48 +++++++++++++++++++--------------------
1 file changed, 24 insertions(+), 24 deletions(-)
diff --git a/arch/arm/boot/dts/imx6sx-sdb.dtsi b/arch/arm/boot/dts/imx6sx-sdb.dtsi
index d57a41c..d35aa85 100644
--- a/arch/arm/boot/dts/imx6sx-sdb.dtsi
+++ b/arch/arm/boot/dts/imx6sx-sdb.dtsi
@@ -24,7 +24,7 @@
reg = <0x80000000 0x40000000>;
};
- backlight {
+ backlight_display: backlight-display {
compatible = "pwm-backlight";
pwms = <&pwm3 0 5000000>;
brightness-levels = <0 4 8 16 32 64 128 255>;
@@ -129,6 +129,13 @@
enable-active-high;
};
+ reg_lcd_5v: regulator-lcd-5v {
+ compatible = "regulator-fixed";
+ regulator-name = "lcd-5v0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
sound {
compatible = "fsl,imx6sx-sdb-wm8962", "fsl,imx-audio-wm8962";
model = "wm8962-audio";
@@ -144,6 +151,19 @@
mux-int-port = <2>;
mux-ext-port = <6>;
};
+
+ panel {
+ compatible = "sii,43wvf1g";
+ backlight = <&backlight_display>;
+ dvdd-supply = <®_lcd_3v3>;
+ avdd-supply = <®_lcd_5v>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&display_out>;
+ };
+ };
+ };
};
&audmux {
@@ -221,31 +241,11 @@
&lcdif1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_lcd>;
- lcd-supply = <®_lcd_3v3>;
- display = <&display0>;
status = "okay";
- display0: display0 {
- bits-per-pixel = <16>;
- bus-width = <24>;
-
- display-timings {
- native-mode = <&timing0>;
- timing0: timing0 {
- clock-frequency = <33500000>;
- hactive = <800>;
- vactive = <480>;
- hback-porch = <89>;
- hfront-porch = <164>;
- vback-porch = <23>;
- vfront-porch = <10>;
- hsync-len = <10>;
- vsync-len = <10>;
- hsync-active = <0>;
- vsync-active = <0>;
- de-active = <1>;
- pixelclk-active = <0>;
- };
+ port {
+ display_out: endpoint {
+ remote-endpoint = <&panel_in>;
};
};
};
--
2.7.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH v3 2/3] ARM: dts: imx6sl-evk: Rearrange the regulators node
2017-12-06 15:15 ` Marco Franchi
(?)
@ 2017-12-06 15:15 ` Marco Franchi
-1 siblings, 0 replies; 12+ messages in thread
From: Marco Franchi @ 2017-12-06 15:15 UTC (permalink / raw)
To: linux-arm-kernel
It is not recommended to place regulators inside "simple-bus", so move
them out.
The motivation for doing this is to make it easier to adding new
regulators.
Signed-off-by: Marco Franchi <marcofrk@gmail.com>
---
Changes since v2:
-include GPIO_ACTIVE_HIGH instead of numerical values
arch/arm/boot/dts/imx6sl-evk.dts | 85 +++++++++++++++++-----------------------
1 file changed, 37 insertions(+), 48 deletions(-)
diff --git a/arch/arm/boot/dts/imx6sl-evk.dts b/arch/arm/boot/dts/imx6sl-evk.dts
index 60600b4..c9114cc 100644
--- a/arch/arm/boot/dts/imx6sl-evk.dts
+++ b/arch/arm/boot/dts/imx6sl-evk.dts
@@ -39,58 +39,47 @@
};
};
- regulators {
- compatible = "simple-bus";
- #address-cells = <1>;
- #size-cells = <0>;
-
- reg_usb_otg1_vbus: regulator at 0 {
- compatible = "regulator-fixed";
- reg = <0>;
- regulator-name = "usb_otg1_vbus";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- gpio = <&gpio4 0 0>;
- enable-active-high;
- vin-supply = <&swbst_reg>;
- };
+ reg_usb_otg1_vbus: regulator-usb-otg1-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_otg1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio4 0 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ vin-supply = <&swbst_reg>;
+ };
- reg_usb_otg2_vbus: regulator at 1 {
- compatible = "regulator-fixed";
- reg = <1>;
- regulator-name = "usb_otg2_vbus";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- gpio = <&gpio4 2 0>;
- enable-active-high;
- vin-supply = <&swbst_reg>;
- };
+ reg_usb_otg2_vbus: regulator-usb-otg2-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_otg2_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio4 2 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ vin-supply = <&swbst_reg>;
+ };
- reg_aud3v: regulator at 2 {
- compatible = "regulator-fixed";
- reg = <2>;
- regulator-name = "wm8962-supply-3v15";
- regulator-min-microvolt = <3150000>;
- regulator-max-microvolt = <3150000>;
- regulator-boot-on;
- };
+ reg_aud3v: regulator-aud3v {
+ compatible = "regulator-fixed";
+ regulator-name = "wm8962-supply-3v15";
+ regulator-min-microvolt = <3150000>;
+ regulator-max-microvolt = <3150000>;
+ regulator-boot-on;
+ };
- reg_aud4v: regulator at 3 {
- compatible = "regulator-fixed";
- reg = <3>;
- regulator-name = "wm8962-supply-4v2";
- regulator-min-microvolt = <4325000>;
- regulator-max-microvolt = <4325000>;
- regulator-boot-on;
- };
+ reg_aud4v: regulator-aud4v {
+ compatible = "regulator-fixed";
+ regulator-name = "wm8962-supply-4v2";
+ regulator-min-microvolt = <4325000>;
+ regulator-max-microvolt = <4325000>;
+ regulator-boot-on;
+ };
- reg_lcd_3v3: regulator at 4 {
- compatible = "regulator-fixed";
- reg = <4>;
- regulator-name = "lcd-3v3";
- gpio = <&gpio4 3 0>;
- enable-active-high;
- };
+ reg_lcd_3v3: regulator-lcd-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "lcd-3v3";
+ gpio = <&gpio4 3 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
};
sound {
--
2.7.4
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH v3 2/3] ARM: dts: imx6sl-evk: Rearrange the regulators node
@ 2017-12-06 15:15 ` Marco Franchi
0 siblings, 0 replies; 12+ messages in thread
From: Marco Franchi @ 2017-12-06 15:15 UTC (permalink / raw)
To: shawnguo
Cc: robh+dt, linux-arm-kernel, linux-kernel, devicetree, festevam,
marcofrk
It is not recommended to place regulators inside "simple-bus", so move
them out.
The motivation for doing this is to make it easier to adding new
regulators.
Signed-off-by: Marco Franchi <marcofrk@gmail.com>
---
Changes since v2:
-include GPIO_ACTIVE_HIGH instead of numerical values
arch/arm/boot/dts/imx6sl-evk.dts | 85 +++++++++++++++++-----------------------
1 file changed, 37 insertions(+), 48 deletions(-)
diff --git a/arch/arm/boot/dts/imx6sl-evk.dts b/arch/arm/boot/dts/imx6sl-evk.dts
index 60600b4..c9114cc 100644
--- a/arch/arm/boot/dts/imx6sl-evk.dts
+++ b/arch/arm/boot/dts/imx6sl-evk.dts
@@ -39,58 +39,47 @@
};
};
- regulators {
- compatible = "simple-bus";
- #address-cells = <1>;
- #size-cells = <0>;
-
- reg_usb_otg1_vbus: regulator@0 {
- compatible = "regulator-fixed";
- reg = <0>;
- regulator-name = "usb_otg1_vbus";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- gpio = <&gpio4 0 0>;
- enable-active-high;
- vin-supply = <&swbst_reg>;
- };
+ reg_usb_otg1_vbus: regulator-usb-otg1-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_otg1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio4 0 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ vin-supply = <&swbst_reg>;
+ };
- reg_usb_otg2_vbus: regulator@1 {
- compatible = "regulator-fixed";
- reg = <1>;
- regulator-name = "usb_otg2_vbus";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- gpio = <&gpio4 2 0>;
- enable-active-high;
- vin-supply = <&swbst_reg>;
- };
+ reg_usb_otg2_vbus: regulator-usb-otg2-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_otg2_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio4 2 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ vin-supply = <&swbst_reg>;
+ };
- reg_aud3v: regulator@2 {
- compatible = "regulator-fixed";
- reg = <2>;
- regulator-name = "wm8962-supply-3v15";
- regulator-min-microvolt = <3150000>;
- regulator-max-microvolt = <3150000>;
- regulator-boot-on;
- };
+ reg_aud3v: regulator-aud3v {
+ compatible = "regulator-fixed";
+ regulator-name = "wm8962-supply-3v15";
+ regulator-min-microvolt = <3150000>;
+ regulator-max-microvolt = <3150000>;
+ regulator-boot-on;
+ };
- reg_aud4v: regulator@3 {
- compatible = "regulator-fixed";
- reg = <3>;
- regulator-name = "wm8962-supply-4v2";
- regulator-min-microvolt = <4325000>;
- regulator-max-microvolt = <4325000>;
- regulator-boot-on;
- };
+ reg_aud4v: regulator-aud4v {
+ compatible = "regulator-fixed";
+ regulator-name = "wm8962-supply-4v2";
+ regulator-min-microvolt = <4325000>;
+ regulator-max-microvolt = <4325000>;
+ regulator-boot-on;
+ };
- reg_lcd_3v3: regulator@4 {
- compatible = "regulator-fixed";
- reg = <4>;
- regulator-name = "lcd-3v3";
- gpio = <&gpio4 3 0>;
- enable-active-high;
- };
+ reg_lcd_3v3: regulator-lcd-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "lcd-3v3";
+ gpio = <&gpio4 3 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
};
sound {
--
2.7.4
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH v3 2/3] ARM: dts: imx6sl-evk: Rearrange the regulators node
@ 2017-12-06 15:15 ` Marco Franchi
0 siblings, 0 replies; 12+ messages in thread
From: Marco Franchi @ 2017-12-06 15:15 UTC (permalink / raw)
To: shawnguo
Cc: devicetree, marcofrk, linux-kernel, robh+dt, festevam,
linux-arm-kernel
It is not recommended to place regulators inside "simple-bus", so move
them out.
The motivation for doing this is to make it easier to adding new
regulators.
Signed-off-by: Marco Franchi <marcofrk@gmail.com>
---
Changes since v2:
-include GPIO_ACTIVE_HIGH instead of numerical values
arch/arm/boot/dts/imx6sl-evk.dts | 85 +++++++++++++++++-----------------------
1 file changed, 37 insertions(+), 48 deletions(-)
diff --git a/arch/arm/boot/dts/imx6sl-evk.dts b/arch/arm/boot/dts/imx6sl-evk.dts
index 60600b4..c9114cc 100644
--- a/arch/arm/boot/dts/imx6sl-evk.dts
+++ b/arch/arm/boot/dts/imx6sl-evk.dts
@@ -39,58 +39,47 @@
};
};
- regulators {
- compatible = "simple-bus";
- #address-cells = <1>;
- #size-cells = <0>;
-
- reg_usb_otg1_vbus: regulator@0 {
- compatible = "regulator-fixed";
- reg = <0>;
- regulator-name = "usb_otg1_vbus";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- gpio = <&gpio4 0 0>;
- enable-active-high;
- vin-supply = <&swbst_reg>;
- };
+ reg_usb_otg1_vbus: regulator-usb-otg1-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_otg1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio4 0 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ vin-supply = <&swbst_reg>;
+ };
- reg_usb_otg2_vbus: regulator@1 {
- compatible = "regulator-fixed";
- reg = <1>;
- regulator-name = "usb_otg2_vbus";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- gpio = <&gpio4 2 0>;
- enable-active-high;
- vin-supply = <&swbst_reg>;
- };
+ reg_usb_otg2_vbus: regulator-usb-otg2-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_otg2_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio4 2 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ vin-supply = <&swbst_reg>;
+ };
- reg_aud3v: regulator@2 {
- compatible = "regulator-fixed";
- reg = <2>;
- regulator-name = "wm8962-supply-3v15";
- regulator-min-microvolt = <3150000>;
- regulator-max-microvolt = <3150000>;
- regulator-boot-on;
- };
+ reg_aud3v: regulator-aud3v {
+ compatible = "regulator-fixed";
+ regulator-name = "wm8962-supply-3v15";
+ regulator-min-microvolt = <3150000>;
+ regulator-max-microvolt = <3150000>;
+ regulator-boot-on;
+ };
- reg_aud4v: regulator@3 {
- compatible = "regulator-fixed";
- reg = <3>;
- regulator-name = "wm8962-supply-4v2";
- regulator-min-microvolt = <4325000>;
- regulator-max-microvolt = <4325000>;
- regulator-boot-on;
- };
+ reg_aud4v: regulator-aud4v {
+ compatible = "regulator-fixed";
+ regulator-name = "wm8962-supply-4v2";
+ regulator-min-microvolt = <4325000>;
+ regulator-max-microvolt = <4325000>;
+ regulator-boot-on;
+ };
- reg_lcd_3v3: regulator@4 {
- compatible = "regulator-fixed";
- reg = <4>;
- regulator-name = "lcd-3v3";
- gpio = <&gpio4 3 0>;
- enable-active-high;
- };
+ reg_lcd_3v3: regulator-lcd-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "lcd-3v3";
+ gpio = <&gpio4 3 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
};
sound {
--
2.7.4
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH v3 3/3] ARM: dts: imx6sl-evk: Convert from fbdev to drm bindings
2017-12-06 15:15 ` Marco Franchi
(?)
@ 2017-12-06 15:15 ` Marco Franchi
-1 siblings, 0 replies; 12+ messages in thread
From: Marco Franchi @ 2017-12-06 15:15 UTC (permalink / raw)
To: linux-arm-kernel
It is preferred to use the panel compatible string rather than passing
the LCD timing in the device tree.
So pass the "sii,43wvf1g" compatible string which describes the parallel
LCD.
Also, pass the 'backlight' property as described in
Documentation/devicetree/bindings/display/panel/simple-panel.txt
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
---
Changes since v2:
-none
arch/arm/boot/dts/imx6sl-evk.dts | 48 ++++++++++++++++++++--------------------
1 file changed, 24 insertions(+), 24 deletions(-)
diff --git a/arch/arm/boot/dts/imx6sl-evk.dts b/arch/arm/boot/dts/imx6sl-evk.dts
index c9114cc..2844ab5 100644
--- a/arch/arm/boot/dts/imx6sl-evk.dts
+++ b/arch/arm/boot/dts/imx6sl-evk.dts
@@ -20,7 +20,7 @@
reg = <0x80000000 0x40000000>;
};
- backlight {
+ backlight_display: backlight_display {
compatible = "pwm-backlight";
pwms = <&pwm1 0 5000000>;
brightness-levels = <0 4 8 16 32 64 128 255>;
@@ -82,6 +82,13 @@
enable-active-high;
};
+ reg_lcd_5v: regulator-lcd-5v {
+ compatible = "regulator-fixed";
+ regulator-name = "lcd-5v0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
sound {
compatible = "fsl,imx6sl-evk-wm8962", "fsl,imx-audio-wm8962";
model = "wm8962-audio";
@@ -97,6 +104,19 @@
mux-int-port = <2>;
mux-ext-port = <3>;
};
+
+ panel {
+ compatible = "sii,43wvf1g";
+ backlight = <&backlight_display>;
+ dvdd-supply = <®_lcd_3v3>;
+ avdd-supply = <®_lcd_5v>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&display_out>;
+ };
+ };
+ };
};
&audmux {
@@ -535,31 +555,11 @@
&lcdif {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_lcd>;
- lcd-supply = <®_lcd_3v3>;
- display = <&display0>;
status = "okay";
- display0: display0 {
- bits-per-pixel = <32>;
- bus-width = <24>;
-
- display-timings {
- native-mode = <&timing0>;
- timing0: timing0 {
- clock-frequency = <33500000>;
- hactive = <800>;
- vactive = <480>;
- hback-porch = <89>;
- hfront-porch = <164>;
- vback-porch = <23>;
- vfront-porch = <10>;
- hsync-len = <10>;
- vsync-len = <10>;
- hsync-active = <0>;
- vsync-active = <0>;
- de-active = <1>;
- pixelclk-active = <0>;
- };
+ port {
+ display_out: endpoint {
+ remote-endpoint = <&panel_in>;
};
};
};
--
2.7.4
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH v3 3/3] ARM: dts: imx6sl-evk: Convert from fbdev to drm bindings
@ 2017-12-06 15:15 ` Marco Franchi
0 siblings, 0 replies; 12+ messages in thread
From: Marco Franchi @ 2017-12-06 15:15 UTC (permalink / raw)
To: shawnguo
Cc: robh+dt, linux-arm-kernel, linux-kernel, devicetree, festevam,
marcofrk, Marco Franchi
It is preferred to use the panel compatible string rather than passing
the LCD timing in the device tree.
So pass the "sii,43wvf1g" compatible string which describes the parallel
LCD.
Also, pass the 'backlight' property as described in
Documentation/devicetree/bindings/display/panel/simple-panel.txt
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
---
Changes since v2:
-none
arch/arm/boot/dts/imx6sl-evk.dts | 48 ++++++++++++++++++++--------------------
1 file changed, 24 insertions(+), 24 deletions(-)
diff --git a/arch/arm/boot/dts/imx6sl-evk.dts b/arch/arm/boot/dts/imx6sl-evk.dts
index c9114cc..2844ab5 100644
--- a/arch/arm/boot/dts/imx6sl-evk.dts
+++ b/arch/arm/boot/dts/imx6sl-evk.dts
@@ -20,7 +20,7 @@
reg = <0x80000000 0x40000000>;
};
- backlight {
+ backlight_display: backlight_display {
compatible = "pwm-backlight";
pwms = <&pwm1 0 5000000>;
brightness-levels = <0 4 8 16 32 64 128 255>;
@@ -82,6 +82,13 @@
enable-active-high;
};
+ reg_lcd_5v: regulator-lcd-5v {
+ compatible = "regulator-fixed";
+ regulator-name = "lcd-5v0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
sound {
compatible = "fsl,imx6sl-evk-wm8962", "fsl,imx-audio-wm8962";
model = "wm8962-audio";
@@ -97,6 +104,19 @@
mux-int-port = <2>;
mux-ext-port = <3>;
};
+
+ panel {
+ compatible = "sii,43wvf1g";
+ backlight = <&backlight_display>;
+ dvdd-supply = <®_lcd_3v3>;
+ avdd-supply = <®_lcd_5v>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&display_out>;
+ };
+ };
+ };
};
&audmux {
@@ -535,31 +555,11 @@
&lcdif {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_lcd>;
- lcd-supply = <®_lcd_3v3>;
- display = <&display0>;
status = "okay";
- display0: display0 {
- bits-per-pixel = <32>;
- bus-width = <24>;
-
- display-timings {
- native-mode = <&timing0>;
- timing0: timing0 {
- clock-frequency = <33500000>;
- hactive = <800>;
- vactive = <480>;
- hback-porch = <89>;
- hfront-porch = <164>;
- vback-porch = <23>;
- vfront-porch = <10>;
- hsync-len = <10>;
- vsync-len = <10>;
- hsync-active = <0>;
- vsync-active = <0>;
- de-active = <1>;
- pixelclk-active = <0>;
- };
+ port {
+ display_out: endpoint {
+ remote-endpoint = <&panel_in>;
};
};
};
--
2.7.4
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH v3 3/3] ARM: dts: imx6sl-evk: Convert from fbdev to drm bindings
@ 2017-12-06 15:15 ` Marco Franchi
0 siblings, 0 replies; 12+ messages in thread
From: Marco Franchi @ 2017-12-06 15:15 UTC (permalink / raw)
To: shawnguo
Cc: devicetree, marcofrk, linux-kernel, robh+dt, Marco Franchi,
festevam, linux-arm-kernel
It is preferred to use the panel compatible string rather than passing
the LCD timing in the device tree.
So pass the "sii,43wvf1g" compatible string which describes the parallel
LCD.
Also, pass the 'backlight' property as described in
Documentation/devicetree/bindings/display/panel/simple-panel.txt
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
---
Changes since v2:
-none
arch/arm/boot/dts/imx6sl-evk.dts | 48 ++++++++++++++++++++--------------------
1 file changed, 24 insertions(+), 24 deletions(-)
diff --git a/arch/arm/boot/dts/imx6sl-evk.dts b/arch/arm/boot/dts/imx6sl-evk.dts
index c9114cc..2844ab5 100644
--- a/arch/arm/boot/dts/imx6sl-evk.dts
+++ b/arch/arm/boot/dts/imx6sl-evk.dts
@@ -20,7 +20,7 @@
reg = <0x80000000 0x40000000>;
};
- backlight {
+ backlight_display: backlight_display {
compatible = "pwm-backlight";
pwms = <&pwm1 0 5000000>;
brightness-levels = <0 4 8 16 32 64 128 255>;
@@ -82,6 +82,13 @@
enable-active-high;
};
+ reg_lcd_5v: regulator-lcd-5v {
+ compatible = "regulator-fixed";
+ regulator-name = "lcd-5v0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
sound {
compatible = "fsl,imx6sl-evk-wm8962", "fsl,imx-audio-wm8962";
model = "wm8962-audio";
@@ -97,6 +104,19 @@
mux-int-port = <2>;
mux-ext-port = <3>;
};
+
+ panel {
+ compatible = "sii,43wvf1g";
+ backlight = <&backlight_display>;
+ dvdd-supply = <®_lcd_3v3>;
+ avdd-supply = <®_lcd_5v>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&display_out>;
+ };
+ };
+ };
};
&audmux {
@@ -535,31 +555,11 @@
&lcdif {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_lcd>;
- lcd-supply = <®_lcd_3v3>;
- display = <&display0>;
status = "okay";
- display0: display0 {
- bits-per-pixel = <32>;
- bus-width = <24>;
-
- display-timings {
- native-mode = <&timing0>;
- timing0: timing0 {
- clock-frequency = <33500000>;
- hactive = <800>;
- vactive = <480>;
- hback-porch = <89>;
- hfront-porch = <164>;
- vback-porch = <23>;
- vfront-porch = <10>;
- hsync-len = <10>;
- vsync-len = <10>;
- hsync-active = <0>;
- vsync-active = <0>;
- de-active = <1>;
- pixelclk-active = <0>;
- };
+ port {
+ display_out: endpoint {
+ remote-endpoint = <&panel_in>;
};
};
};
--
2.7.4
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH v3 1/3] ARM: dts: imx6sx-sdb: Convert from fbdev to drm bindings
@ 2017-12-21 8:22 ` Shawn Guo
0 siblings, 0 replies; 12+ messages in thread
From: Shawn Guo @ 2017-12-21 8:22 UTC (permalink / raw)
To: linux-arm-kernel
On Wed, Dec 06, 2017 at 01:15:17PM -0200, Marco Franchi wrote:
> It is preferred to use the panel compatible string rather than passing
> the LCD timing in the device tree.
>
> So pass the "sii,43wvf1g" compatible string, which describes the parallel
> LCD.
>
> Also pass the 'backlight' property as described in
> Documentation/devicetree/bindings/display/panel/simple-panel.txt
>
> Signed-off-by: Marco Franchi <marcofrk@gmail.com>
Applied all, thanks.
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH v3 1/3] ARM: dts: imx6sx-sdb: Convert from fbdev to drm bindings
@ 2017-12-21 8:22 ` Shawn Guo
0 siblings, 0 replies; 12+ messages in thread
From: Shawn Guo @ 2017-12-21 8:22 UTC (permalink / raw)
To: Marco Franchi
Cc: robh+dt, linux-arm-kernel, linux-kernel, devicetree, festevam
On Wed, Dec 06, 2017 at 01:15:17PM -0200, Marco Franchi wrote:
> It is preferred to use the panel compatible string rather than passing
> the LCD timing in the device tree.
>
> So pass the "sii,43wvf1g" compatible string, which describes the parallel
> LCD.
>
> Also pass the 'backlight' property as described in
> Documentation/devicetree/bindings/display/panel/simple-panel.txt
>
> Signed-off-by: Marco Franchi <marcofrk@gmail.com>
Applied all, thanks.
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH v3 1/3] ARM: dts: imx6sx-sdb: Convert from fbdev to drm bindings
@ 2017-12-21 8:22 ` Shawn Guo
0 siblings, 0 replies; 12+ messages in thread
From: Shawn Guo @ 2017-12-21 8:22 UTC (permalink / raw)
To: Marco Franchi
Cc: robh+dt-DgEjT+Ai2ygdnm+yROfE0A,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
festevam-Re5JQEeQqe8AvxtiuMwx3w
On Wed, Dec 06, 2017 at 01:15:17PM -0200, Marco Franchi wrote:
> It is preferred to use the panel compatible string rather than passing
> the LCD timing in the device tree.
>
> So pass the "sii,43wvf1g" compatible string, which describes the parallel
> LCD.
>
> Also pass the 'backlight' property as described in
> Documentation/devicetree/bindings/display/panel/simple-panel.txt
>
> Signed-off-by: Marco Franchi <marcofrk-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
Applied all, thanks.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 12+ messages in thread