[U-Boot] [PATCH v1 01/07] db410c: configs: increase gunzip buffer size for the kernel

[U-Boot] [PATCH v1 01/07] db410c: configs: increase gunzip buffer size for the kernel

[Jorge Ramirez-Ortiz]

From: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>

the kernel fails to boot when it goes over the limit.

Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
---
 include/configs/dragonboard410c.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/include/configs/dragonboard410c.h b/include/configs/dragonboard410c.h
index d2447b2..3c5bb8a 100644
--- a/include/configs/dragonboard410c.h
+++ b/include/configs/dragonboard410c.h
@@ -23,7 +23,7 @@
 #define CONFIG_SYS_TEXT_BASE		0x80080000
 #define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_SDRAM_BASE + 0x7fff0)
 #define CONFIG_SYS_LOAD_ADDR		(CONFIG_SYS_SDRAM_BASE + 0x80000)
-#define CONFIG_SYS_BOOTM_LEN		0x1000000 /* 16MB max kernel size */
+#define CONFIG_SYS_BOOTM_LEN		SZ_64M
 
 /* UART */
 
-- 
2.7.4

[U-Boot] [PATCH v1 02/07] db410c: update wlan and bt mac addresses from firmware

[Jorge Ramirez-Ortiz]

From: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>

The firmware that runs before u-boot modifies u-boot's device tree
adding the local-mac-address and local-bd-address properties for the
compatibles "qcom,wcnss-bt" and "qcom,wcnss-wlan".

This commit reads that firmware, retrieves the properties and fixups
the device tree that is passed to the kernel before booting.

Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
---
 arch/arm/dts/dragonboard410c.dts                 | 10 +++++
 board/qualcomm/dragonboard410c/Makefile          |  1 +
 board/qualcomm/dragonboard410c/dragonboard410c.c | 49 +++++++++++++++++++++---
 board/qualcomm/dragonboard410c/lowlevel_init.S   | 28 ++++++++++++++
 configs/dragonboard410c_defconfig                |  3 ++
 5 files changed, 85 insertions(+), 6 deletions(-)
 create mode 100644 board/qualcomm/dragonboard410c/lowlevel_init.S

diff --git a/arch/arm/dts/dragonboard410c.dts b/arch/arm/dts/dragonboard410c.dts
index 7746622..25aeac4 100644
--- a/arch/arm/dts/dragonboard410c.dts
+++ b/arch/arm/dts/dragonboard410c.dts
@@ -86,6 +86,16 @@
 			clock-frequency = <200000000>;
 		};
 
+		wcnss {
+			bt {
+				compatible="qcom,wcnss-bt";
+			};
+
+			wifi {
+				compatible="qcom,wcnss-wlan";
+			};
+		};
+
 		spmi at 200f000 {
 			compatible = "qcom,spmi-pmic-arb";
 			reg = <0x200f800 0x200 0x2400000 0x400000 0x2c00000 0x400000>;
diff --git a/board/qualcomm/dragonboard410c/Makefile b/board/qualcomm/dragonboard410c/Makefile
index cd67808..5082383 100644
--- a/board/qualcomm/dragonboard410c/Makefile
+++ b/board/qualcomm/dragonboard410c/Makefile
@@ -5,4 +5,5 @@
 #
 
 obj-y	:= dragonboard410c.o
+obj-y	+= lowlevel_init.o
 extra-y += head.o
diff --git a/board/qualcomm/dragonboard410c/dragonboard410c.c b/board/qualcomm/dragonboard410c/dragonboard410c.c
index 848e278..99fc91b 100644
--- a/board/qualcomm/dragonboard410c/dragonboard410c.c
+++ b/board/qualcomm/dragonboard410c/dragonboard410c.c
@@ -10,9 +10,16 @@
 #include <dm.h>
 #include <usb.h>
 #include <asm/gpio.h>
+#include <fdt_support.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
+/* pointer to the device tree ammended by the firmware */
+extern const void *fw_dtb;
+
+static char wlan_mac[ARP_HLEN];
+static char bt_mac[ARP_HLEN];
+
 int dram_init(void)
 {
 	gd->ram_size = PHYS_SDRAM_1_SIZE;
@@ -27,7 +34,6 @@ int dram_init_banksize(void)
 	return 0;
 }
 
-
 int board_prepare_usb(enum usb_init_type type)
 {
 	static struct udevice *pmic_gpio;
@@ -96,11 +102,6 @@ int board_prepare_usb(enum usb_init_type type)
 	return 0;
 }
 
-int board_init(void)
-{
-	return 0;
-}
-
 /* Check for vol- button - if pressed - stop autoboot */
 int misc_init_r(void)
 {
@@ -134,3 +135,39 @@ int misc_init_r(void)
 
 	return 0;
 }
+
+int board_init(void)
+{
+	int offset, len;
+	const char *mac;
+
+	/* take a copy of the firmware information (the user could unknownly
+	   overwrite that DDR via tftp or other means)  */
+
+	offset = fdt_node_offset_by_compatible(fw_dtb, -1, "qcom,wcnss-wlan");
+	if (offset >= 0) {
+		mac = fdt_getprop(fw_dtb, offset, "local-mac-address", &len);
+		if (mac)
+			memcpy(wlan_mac, mac, ARP_HLEN);
+	}
+
+	offset = fdt_node_offset_by_compatible(fw_dtb, -1, "qcom,wcnss-bt");
+	if (offset >= 0) {
+		mac = fdt_getprop(fw_dtb, offset, "local-bd-address", &len);
+		if (mac)
+			memcpy(bt_mac, mac, ARP_HLEN);
+	}
+
+	return 0;
+}
+
+int ft_board_setup(void *blob, bd_t *bd)
+{
+	do_fixup_by_compat(blob, "qcom,wcnss-wlan", "local-mac-address",
+		wlan_mac, ARP_HLEN, 1);
+
+	do_fixup_by_compat(blob, "qcom,wcnss-bt", "local-bd-address",
+		bt_mac, ARP_HLEN, 1);
+
+	return 0;
+}
diff --git a/board/qualcomm/dragonboard410c/lowlevel_init.S b/board/qualcomm/dragonboard410c/lowlevel_init.S
new file mode 100644
index 0000000..15b2d0c
--- /dev/null
+++ b/board/qualcomm/dragonboard410c/lowlevel_init.S
@@ -0,0 +1,28 @@
+/*
+ * (C) Copyright 2016
+ * Cédric Schieli <cschieli@gmail.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <config.h>
+
+.align 8
+.global fw_dtb
+fw_dtb:
+	.dword 0x0
+
+/*
+ * Routine: save_boot_params (called after reset from start.S)
+ * Description: save ATAG/FDT address provided by the firmware at boot time
+ */
+
+.global save_boot_params
+save_boot_params:
+
+	/* The firmware provided ATAG/FDT address can be found in r2/x0 */
+	adr	x8, fw_dtb
+	str	x0, [x8]
+
+	/* Returns */
+	b	save_boot_params_ret
diff --git a/configs/dragonboard410c_defconfig b/configs/dragonboard410c_defconfig
index b71bff7..cfe9be9 100644
--- a/configs/dragonboard410c_defconfig
+++ b/configs/dragonboard410c_defconfig
@@ -44,3 +44,6 @@ CONFIG_USB_ETHER_ASIX88179=y
 CONFIG_USB_ETHER_MCS7830=y
 CONFIG_USB_ETHER_SMSC95XX=y
 CONFIG_OF_LIBFDT_OVERLAY=y
+CONFIG_OF_CONTROL=y
+CONFIG_ENV_IS_IN_MMC=y
+CONFIG_OF_BOARD_SETUP=y
-- 
2.7.4

[U-Boot] [PATCH v1 03/07] db410c: replace reset driver with psci

[Jorge Ramirez-Ortiz]

From: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>

this should be the norm for armv8 platforms.

Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
---
 arch/arm/dts/dragonboard410c.dts                 |  5 ---
 board/qualcomm/dragonboard410c/dragonboard410c.c |  5 +++
 configs/dragonboard410c_defconfig                |  2 +-
 drivers/sysreset/Makefile                        |  2 --
 drivers/sysreset/sysreset_snapdragon.c           | 40 ------------------------
 5 files changed, 6 insertions(+), 48 deletions(-)
 delete mode 100644 drivers/sysreset/sysreset_snapdragon.c

diff --git a/arch/arm/dts/dragonboard410c.dts b/arch/arm/dts/dragonboard410c.dts
index 25aeac4..b67e588 100644
--- a/arch/arm/dts/dragonboard410c.dts
+++ b/arch/arm/dts/dragonboard410c.dts
@@ -48,11 +48,6 @@
 			clock = <&clkc 4>;
 		};
 
-		restart at 4ab000 {
-			compatible = "qcom,pshold";
-			reg = <0x4ab000 0x4>;
-		};
-
 		soc_gpios: pinctrl at 1000000 {
 			compatible = "qcom,apq8016-pinctrl";
 			reg = <0x1000000 0x300000>;
diff --git a/board/qualcomm/dragonboard410c/dragonboard410c.c b/board/qualcomm/dragonboard410c/dragonboard410c.c
index 99fc91b..8ef4338 100644
--- a/board/qualcomm/dragonboard410c/dragonboard410c.c
+++ b/board/qualcomm/dragonboard410c/dragonboard410c.c
@@ -171,3 +171,8 @@ int ft_board_setup(void *blob, bd_t *bd)
 
 	return 0;
 }
+
+void reset_cpu(ulong addr)
+{
+	psci_system_reset();
+}
diff --git a/configs/dragonboard410c_defconfig b/configs/dragonboard410c_defconfig
index cfe9be9..de923ad 100644
--- a/configs/dragonboard410c_defconfig
+++ b/configs/dragonboard410c_defconfig
@@ -30,7 +30,6 @@ CONFIG_DM_PMIC=y
 CONFIG_PMIC_PM8916=y
 CONFIG_MSM_SERIAL=y
 CONFIG_SPMI_MSM=y
-CONFIG_SYSRESET=y
 CONFIG_USB=y
 CONFIG_DM_USB=y
 CONFIG_USB_EHCI_HCD=y
@@ -47,3 +46,4 @@ CONFIG_OF_LIBFDT_OVERLAY=y
 CONFIG_OF_CONTROL=y
 CONFIG_ENV_IS_IN_MMC=y
 CONFIG_OF_BOARD_SETUP=y
+CONFIG_PSCI_RESET=y
diff --git a/drivers/sysreset/Makefile b/drivers/sysreset/Makefile
index 2e9598e..000c288 100644
--- a/drivers/sysreset/Makefile
+++ b/drivers/sysreset/Makefile
@@ -8,10 +8,8 @@ obj-$(CONFIG_SYSRESET) += sysreset-uclass.o
 obj-$(CONFIG_SYSRESET_PSCI) += sysreset_psci.o
 obj-$(CONFIG_SYSRESET_SYSCON) += sysreset_syscon.o
 obj-$(CONFIG_SYSRESET_WATCHDOG) += sysreset_watchdog.o
-
 obj-$(CONFIG_ARCH_ROCKCHIP) += sysreset_rockchip.o
 obj-$(CONFIG_SANDBOX) += sysreset_sandbox.o
-obj-$(CONFIG_ARCH_SNAPDRAGON) += sysreset_snapdragon.o
 obj-$(CONFIG_ARCH_STI) += sysreset_sti.o
 obj-$(CONFIG_TARGET_XTFPGA) += sysreset_xtfpga.o
 obj-$(CONFIG_ARCH_ASPEED) += sysreset_ast.o
diff --git a/drivers/sysreset/sysreset_snapdragon.c b/drivers/sysreset/sysreset_snapdragon.c
deleted file mode 100644
index 9869813..0000000
--- a/drivers/sysreset/sysreset_snapdragon.c
+++ /dev/null
@@ -1,40 +0,0 @@
-/*
- * Qualcomm APQ8016 reset controller driver
- *
- * (C) Copyright 2015 Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <dm.h>
-#include <errno.h>
-#include <sysreset.h>
-#include <asm/io.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-static int msm_sysreset_request(struct udevice *dev, enum sysreset_t type)
-{
-	phys_addr_t addr = devfdt_get_addr(dev);
-	if (!addr)
-		return -EINVAL;
-	writel(0, addr);
-	return -EINPROGRESS;
-}
-
-static struct sysreset_ops msm_sysreset_ops = {
-	.request	= msm_sysreset_request,
-};
-
-static const struct udevice_id msm_sysreset_ids[] = {
-	{ .compatible = "qcom,pshold" },
-	{ }
-};
-
-U_BOOT_DRIVER(msm_reset) = {
-	.name		= "msm_sysreset",
-	.id		= UCLASS_SYSRESET,
-	.of_match	= msm_sysreset_ids,
-	.ops		= &msm_sysreset_ops,
-};
-- 
2.7.4

[U-Boot] [PATCH v1 04/07] fdtdec: allow board to provide fdt for CONFIG_OF_SEPARATE

[Jorge Ramirez-Ortiz]

From: Rob Clark <robdclark@gmail.com>

Similar to CONFIG_OF_BOARD, but in this case the fdt is still built by
u-boot build.  This allows the board to patch the fdt, etc.

In the specific case of dragonboard 410c, we pass the u-boot generated
fdt to the previous stage of bootloader (by embedding it in the
u-boot.img that is loaded by lk/aboot), which patches the fdt and passes
it back to u-boot.

Signed-off-by: Rob Clark <robdclark@gmail.com>
---
 include/fdtdec.h |  3 ++-
 lib/fdtdec.c     | 35 +++++++++++++++++++++++------------
 2 files changed, 25 insertions(+), 13 deletions(-)

diff --git a/include/fdtdec.h b/include/fdtdec.h
index 0fb3e07..4afb9ac 100644
--- a/include/fdtdec.h
+++ b/include/fdtdec.h
@@ -990,7 +990,8 @@ int fdtdec_setup(void);
 
 /**
  * Board-specific FDT initialization. Returns the address to a device tree blob.
- * Called when CONFIG_OF_BOARD is defined.
+ * Called when CONFIG_OF_BOARD is defined, or if CONFIG_OF_SEPARATE is defined
+ * and the board implements it.
  */
 void *board_fdt_blob_setup(void);
 
diff --git a/lib/fdtdec.c b/lib/fdtdec.c
index 30ec6b9..cc3dfd6 100644
--- a/lib/fdtdec.c
+++ b/lib/fdtdec.c
@@ -1272,6 +1272,28 @@ static int uncompress_blob(const void *src, ulong sz_src, void **dstp)
 # endif
 #endif
 
+#if CONFIG_IS_ENABLED(OF_SEPARATE)
+/*
+ * For CONFIG_OF_SEPARATE, the board may optionally implement this to
+ * provide and/or fixup the fdt.
+ */
+__weak void *board_fdt_blob_setup(void)
+{
+	void *fdt_blob = NULL;
+#ifdef CONFIG_SPL_BUILD
+	/* FDT is at end of BSS unless it is in a different memory region */
+	if (IS_ENABLED(CONFIG_SPL_SEPARATE_BSS))
+		fdt_blob = (ulong *)&_image_binary_end;
+	else
+		fdt_blob = (ulong *)&__bss_end;
+#else
+	/* FDT is at end of image */
+	fdt_blob = (ulong *)&_end;
+#endif
+	return fdt_blob;
+}
+#endif
+
 int fdtdec_setup(void)
 {
 #if CONFIG_IS_ENABLED(OF_CONTROL)
@@ -1285,18 +1307,7 @@ int fdtdec_setup(void)
 #  else
 	gd->fdt_blob = __dtb_dt_begin;
 #  endif
-# elif defined CONFIG_OF_SEPARATE
-#  ifdef CONFIG_SPL_BUILD
-	/* FDT is at end of BSS unless it is in a different memory region */
-	if (IS_ENABLED(CONFIG_SPL_SEPARATE_BSS))
-		gd->fdt_blob = (ulong *)&_image_binary_end;
-	else
-		gd->fdt_blob = (ulong *)&__bss_end;
-#  else
-	/* FDT is at end of image */
-	gd->fdt_blob = (ulong *)&_end;
-#  endif
-# elif defined(CONFIG_OF_BOARD)
+# elif defined(CONFIG_OF_BOARD) || defined (CONFIG_OF_SEPARATE)
 	/* Allow the board to override the fdt address. */
 	gd->fdt_blob = board_fdt_blob_setup();
 # elif defined(CONFIG_OF_HOSTFILE)
-- 
2.7.4

[U-Boot] [PATCH v1 05/07] db410c: use the device tree parsed by the lk loader.

[Jorge Ramirez-Ortiz]

From: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>

We dont need to keep copies of the properties that we are going to
fixup since we will be using the dtb provided by the firmware.

Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
---
 board/qualcomm/dragonboard410c/dragonboard410c.c | 71 ++++++++++++++----------
 configs/dragonboard410c_defconfig                |  1 +
 2 files changed, 44 insertions(+), 28 deletions(-)

diff --git a/board/qualcomm/dragonboard410c/dragonboard410c.c b/board/qualcomm/dragonboard410c/dragonboard410c.c
index 8ef4338..236160a 100644
--- a/board/qualcomm/dragonboard410c/dragonboard410c.c
+++ b/board/qualcomm/dragonboard410c/dragonboard410c.c
@@ -15,14 +15,22 @@
 DECLARE_GLOBAL_DATA_PTR;
 
 /* pointer to the device tree ammended by the firmware */
-extern const void *fw_dtb;
+extern void *fw_dtb;
 
-static char wlan_mac[ARP_HLEN];
-static char bt_mac[ARP_HLEN];
+void *board_fdt_blob_setup(void)
+{
+	if (fdt_magic(fw_dtb) != FDT_MAGIC) {
+		printf("Firmware provided invalid dtb!\n");
+		return NULL;
+	}
+
+	return fw_dtb;
+}
 
 int dram_init(void)
 {
 	gd->ram_size = PHYS_SDRAM_1_SIZE;
+
 	return 0;
 }
 
@@ -138,36 +146,43 @@ int misc_init_r(void)
 
 int board_init(void)
 {
-	int offset, len;
-	const char *mac;
-
-	/* take a copy of the firmware information (the user could unknownly
-	   overwrite that DDR via tftp or other means)  */
-
-	offset = fdt_node_offset_by_compatible(fw_dtb, -1, "qcom,wcnss-wlan");
-	if (offset >= 0) {
-		mac = fdt_getprop(fw_dtb, offset, "local-mac-address", &len);
-		if (mac)
-			memcpy(wlan_mac, mac, ARP_HLEN);
-	}
-
-	offset = fdt_node_offset_by_compatible(fw_dtb, -1, "qcom,wcnss-bt");
-	if (offset >= 0) {
-		mac = fdt_getprop(fw_dtb, offset, "local-bd-address", &len);
-		if (mac)
-			memcpy(bt_mac, mac, ARP_HLEN);
-	}
-
 	return 0;
 }
 
 int ft_board_setup(void *blob, bd_t *bd)
 {
-	do_fixup_by_compat(blob, "qcom,wcnss-wlan", "local-mac-address",
-		wlan_mac, ARP_HLEN, 1);
-
-	do_fixup_by_compat(blob, "qcom,wcnss-bt", "local-bd-address",
-		bt_mac, ARP_HLEN, 1);
+	int offset, len, i;
+	const char *mac;
+	struct {
+		const char *compatible;
+		const char *property;
+	} fix[] = {
+		[0] = {
+			/* update the kernel's dtb with wlan mac */
+			.compatible = "qcom,wcnss-wlan",
+			.property = "local-mac-address",
+		},
+		[1] = {
+			/* update the kernel's dtb with bt mac */
+			.compatible = "qcom,wcnss-bt",
+			.property = "local-bd-address",
+		},
+	};
+
+	for ( i = 0; i < sizeof(fix)/sizeof(fix[0]); i++) {
+
+		offset = fdt_node_offset_by_compatible(gd->fdt_blob, -1,
+							fix[i].compatible);
+		if (offset < 0)
+			continue;
+
+		mac = fdt_getprop(gd->fdt_blob, offset, fix[i].property, &len);
+		if (mac)
+			do_fixup_by_compat(blob,
+				fix[i].compatible,
+				fix[i].property,
+				mac, ARP_HLEN, 1);
+	}
 
 	return 0;
 }
diff --git a/configs/dragonboard410c_defconfig b/configs/dragonboard410c_defconfig
index de923ad..4389f52 100644
--- a/configs/dragonboard410c_defconfig
+++ b/configs/dragonboard410c_defconfig
@@ -47,3 +47,4 @@ CONFIG_OF_CONTROL=y
 CONFIG_ENV_IS_IN_MMC=y
 CONFIG_OF_BOARD_SETUP=y
 CONFIG_PSCI_RESET=y
+CONFIG_OF_SEPARATE=y
-- 
2.7.4

[U-Boot] [PATCH v1 06/07] db410c: add reserved-memory node to dts

[Jorge Ramirez-Ortiz]

From: Rob Clark <robdclark@gmail.com>

If lk lights up display and populates simple-framebuffer node, it will
also setup a reserved-memory node (needed by simplefb on linux).  But
it isn't clever enough to cope when the reserved-memory node is not
present.

Signed-off-by: Rob Clark <robdclark@gmail.com>
---
 arch/arm/dts/dragonboard410c.dts | 7 ++++++-
 1 file changed, 6 insertions(+), 1 deletion(-)

diff --git a/arch/arm/dts/dragonboard410c.dts b/arch/arm/dts/dragonboard410c.dts
index b67e588..5ccfe7f 100644
--- a/arch/arm/dts/dragonboard410c.dts
+++ b/arch/arm/dts/dragonboard410c.dts
@@ -23,11 +23,16 @@
 		reg = <0 0x80000000 0 0x3da00000>;
 	};
 
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+	};
+
 	chosen {
 		stdout-path = "/soc/serial at 78b0000";
 	};
 
-
 	soc {
 		#address-cells = <0x1>;
 		#size-cells = <0x1>;
-- 
2.7.4

[U-Boot] [PATCH v1 07/07] db410c: on aarch64 the fdtfile is in per-vendor subdirectory

[Jorge Ramirez-Ortiz]

From: Rob Clark <robdclark@gmail.com>

Signed-off-by: Rob Clark <robdclark@gmail.com>
---
 include/configs/dragonboard410c.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/include/configs/dragonboard410c.h b/include/configs/dragonboard410c.h
index 3c5bb8a..530d667 100644
--- a/include/configs/dragonboard410c.h
+++ b/include/configs/dragonboard410c.h
@@ -92,7 +92,7 @@ REFLASH(dragonboard/u-boot.img, 8)\
 	"initrd_high=0xffffffffffffffff\0" \
 	"linux_image=Image\0" \
 	"kernel_addr_r=0x81000000\0"\
-	"fdtfile=apq8016-sbc.dtb\0" \
+	"fdtfile=qcom/apq8016-sbc.dtb\0" \
 	"fdt_addr_r=0x83000000\0"\
 	"ramdisk_addr_r=0x84000000\0"\
 	"scriptaddr=0x90000000\0"\
-- 
2.7.4

[U-Boot] [U-Boot, v1, 01/07] db410c: configs: increase gunzip buffer size for the kernel

[Tom Rini]

On Wed, Jan 10, 2018 at 11:34:34AM +0100, Jorge Ramirez-Ortiz wrote:

> From: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
> 
> the kernel fails to boot when it goes over the limit.
> 
> Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>

Applied to u-boot/master, thanks!

-- 
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20180115/927ad1b3/attachment.sig>

[U-Boot] [U-Boot, v1, 02/07] db410c: update wlan and bt mac addresses from firmware

[Tom Rini]

On Wed, Jan 10, 2018 at 11:34:35AM +0100, Jorge Ramirez-Ortiz wrote:

> From: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
> 
> The firmware that runs before u-boot modifies u-boot's device tree
> adding the local-mac-address and local-bd-address properties for the
> compatibles "qcom,wcnss-bt" and "qcom,wcnss-wlan".
> 
> This commit reads that firmware, retrieves the properties and fixups
> the device tree that is passed to the kernel before booting.
> 
> Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>

Applied to u-boot/master, thanks!

-- 
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20180115/d1ff3719/attachment.sig>

[U-Boot] [U-Boot, v1, 03/07] db410c: replace reset driver with psci

[Tom Rini]

On Wed, Jan 10, 2018 at 11:34:36AM +0100, Jorge Ramirez-Ortiz wrote:

> From: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
> 
> this should be the norm for armv8 platforms.
> 
> Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>

Applied to u-boot/master, thanks!

-- 
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20180115/901ce048/attachment.sig>

[U-Boot] [U-Boot, v1, 04/07] fdtdec: allow board to provide fdt for CONFIG_OF_SEPARATE

[Tom Rini]

On Wed, Jan 10, 2018 at 11:34:37AM +0100, Jorge Ramirez-Ortiz wrote:

> From: Rob Clark <robdclark@gmail.com>
> 
> Similar to CONFIG_OF_BOARD, but in this case the fdt is still built by
> u-boot build.  This allows the board to patch the fdt, etc.
> 
> In the specific case of dragonboard 410c, we pass the u-boot generated
> fdt to the previous stage of bootloader (by embedding it in the
> u-boot.img that is loaded by lk/aboot), which patches the fdt and passes
> it back to u-boot.
> 
> Signed-off-by: Rob Clark <robdclark@gmail.com>

Applied to u-boot/master, thanks!

-- 
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20180115/8dcc4a35/attachment.sig>

[U-Boot] [U-Boot, v1, 05/07] db410c: use the device tree parsed by the lk loader.

[Tom Rini]

On Wed, Jan 10, 2018 at 11:34:38AM +0100, Jorge Ramirez-Ortiz wrote:

> From: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
> 
> We dont need to keep copies of the properties that we are going to
> fixup since we will be using the dtb provided by the firmware.
> 
> Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>

Applied to u-boot/master, thanks!

-- 
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20180115/a77595ae/attachment.sig>

[U-Boot] [U-Boot, v1, 06/07] db410c: add reserved-memory node to dts

[Tom Rini]

On Wed, Jan 10, 2018 at 11:34:39AM +0100, Jorge Ramirez-Ortiz wrote:

> From: Rob Clark <robdclark@gmail.com>
> 
> If lk lights up display and populates simple-framebuffer node, it will
> also setup a reserved-memory node (needed by simplefb on linux).  But
> it isn't clever enough to cope when the reserved-memory node is not
> present.
> 
> Signed-off-by: Rob Clark <robdclark@gmail.com>

Applied to u-boot/master, thanks!

-- 
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20180115/839a5883/attachment.sig>

[U-Boot] [U-Boot, v1, 07/07] db410c: on aarch64 the fdtfile is in per-vendor subdirectory

[Tom Rini]

On Wed, Jan 10, 2018 at 11:34:40AM +0100, Jorge Ramirez-Ortiz wrote:

> From: Rob Clark <robdclark@gmail.com>
> 
> Signed-off-by: Rob Clark <robdclark@gmail.com>

Applied to u-boot/master, thanks!

-- 
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20180115/fc960e83/attachment.sig>