[PATCH] ARM: dts: imx: Add support for Advantech DMS-BA16

[shawnguo@kernel.org (Shawn Guo)]

On Mon, Feb 05, 2018 at 02:45:14AM +0800, Ken Lin wrote:
> Add support for Advantech DMS-BA16 board, which use
> the Advantech BA-16 module.
> 
> Signed-off-by: Ken Lin <yungching0725@gmail.com>
> ---
>  arch/arm/boot/dts/Makefile           |   1 +
>  arch/arm/boot/dts/imx6q-dms-ba16.dts | 154 +++++++++++++++++++++++++++++++++++
>  2 files changed, 155 insertions(+)
>  create mode 100644 arch/arm/boot/dts/imx6q-dms-ba16.dts
> 
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index ade7a38543dc..d97511273f30 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -428,6 +428,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
>  	imx6q-b450v3.dtb \
>  	imx6q-b650v3.dtb \
>  	imx6q-b850v3.dtb \
> +	imx6q-dms-ba16.dtb \
>  	imx6q-cm-fx6.dtb \
>  	imx6q-cubox-i.dtb \
>  	imx6q-cubox-i-emmc-som-v15.dtb \
> diff --git a/arch/arm/boot/dts/imx6q-dms-ba16.dts b/arch/arm/boot/dts/imx6q-dms-ba16.dts
> new file mode 100644
> index 000000000000..4c5e17a17cbd
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6q-dms-ba16.dts
> @@ -0,0 +1,154 @@
> +/*
> + * Copyright 2018 Advantech Corporation
> + *
> + * The code contained herein is licensed under the GNU General Public
> + * License. You may obtain a copy of the GNU General Public License
> + * Version 2 or later at the following locations:
> + *
> + * http://www.opensource.org/licenses/gpl-license.html
> + * http://www.gnu.org/copyleft/gpl.html
> + */

Please use SPDX tag.

> +
> +/dts-v1/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include "imx6q-ba16.dtsi"
> +
> +/ {
> +	model = "Advantech DMS-BA16";
> +	compatible = "fsl,imx6q-dms-ba16", "fsl,imx6q";
> +
> +	clocks {
> +		mclk: clock at 0 {

Please give it an unique name like clock-xxx and put it directly under
root, and drop unit-address and 'reg' property.

> +			compatible = "fixed-clock";
> +			reg = <0>;
> +			#clock-cells = <0>;
> +			clock-frequency = <22000000>;
> +		};
> +	};
> +
> +	sound {
> +		compatible = "fsl,imx6q-ba16-sgtl5000",
> +			     "fsl,imx-audio-sgtl5000";
> +		model = "imx6q-ba16-sgtl5000";
> +		ssi-controller = <&ssi1>;
> +		audio-codec = <&sgtl5000>;
> +		audio-routing =
> +			"MIC_IN", "Mic Jack",
> +			"Mic Jack", "Mic Bias",
> +			"Headphone Jack", "HP_OUT";
> +		mux-int-port = <1>;
> +		mux-ext-port = <4>;
> +	};
> +
> +	reg_usb_otg_vbus: regulator-usbotgvbus {
> +		compatible = "regulator-fixed";
> +		regulator-name = "usb_otg_vbus";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_usbotgvbus>;
> +		gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +	};
> +};
> +
> +&iomuxc {
> +
> +	pinctrl_usbotgvbus: usbotgvbusgrp {

Please sort pinctrl entries alphabetically.

> +		fsl,pins = <
> +			MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x000b0
> +			MX6QDL_PAD_GPIO_1__USB_OTG_ID   0x17059
> +		>;
> +	};
> +
> +	pinctrl_i2c1_gpio: i2c1gpiogrp {
> +		fsl,pins = <
> +			MX6QDL_PAD_CSI0_DAT8__GPIO5_IO26        0x1b0b0
> +			MX6QDL_PAD_CSI0_DAT9__GPIO5_IO27        0x1b0b0
> +		>;
> +	};
> +
> +	pinctrl_i2c2_gpio: i2c2gpiogrp {
> +		fsl,pins = <
> +			MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x1b0b0
> +			MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x1b0b0
> +		>;
> +	};
> +
> +	pinctrl_i2c3_gpio: i2c3gpiogrp {
> +		fsl,pins = <
> +			MX6QDL_PAD_GPIO_3__GPIO1_IO03   0x1b0b0
> +			MX6QDL_PAD_GPIO_6__GPIO1_IO06   0x1b0b0
> +		>;
> +	};
> +};
> +
> +&ecspi5 {
> +	fsl,spi-num-chipselects = <1>;

The property is obsoleted, and shouldn't be needed any more.

> +	cs-gpios = <&gpio1 17 0>;

Use polarity defines in dt-bindings/gpio/gpio.h.

> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_ecspi5>;
> +	status = "okay";
> +
> +	m25_eeprom: m25p80 at 0 {
> +		compatible = "atmel,at25";
> +		spi-max-frequency = <20000000>;
> +		size = <0x8000>;
> +		pagesize = <64>;
> +		reg = <0>;
> +		address-width = <16>;
> +	};
> +};
> +
> +&i2c1 {
> +	clock-frequency = <100000>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_i2c1>;
> +	status = "okay";
> +
> +	sgtl5000: codec at 0a {

Drop the leading zeros in unit-address.

> +		compatible = "fsl,sgtl5000";
> +		reg = <0x0a>;
> +		clocks = <&mclk>;
> +		lrclk-strength = <0x3>;
> +		VDDA-supply = <&reg_1p8v>;
> +		VDDIO-supply = <&reg_3p3v>;
> +	};
> +};
> +
> +&usbotg {
> +	vbus-supply = <&reg_usb_otg_vbus>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_usbotg>;
> +	dr_mode = "otg";
> +	disable-over-current;
> +	status = "okay";
> +};
> +
> +&sata {
> +	fsl,no-spread-spectrum;
> +	fsl,transmit-atten-16ths = <12>;
> +	fsl,transmit-boost-mdB = <3330>;
> +	fsl,transmit-level-mV = <1133>;
> +	fsl,receive-dpll-mode = <1>;
> +	status = "okay";
> +};
> +
> +&usdhc4 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_usdhc4>;
> +	bus-width = <8>;
> +	cd-gpios = <&gpio6 11 1>;

Polarity defines.

> +	no-1-8-v;
> +	keep-power-in-suspend;
> +	enable-sdio-wakeup;

Use property 'wakeup-source' instead.

> +	status = "okay";
> +};
> +
> +&pwm2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_pwm2>;
> +	status = "okay";
> +};

Please sort these labelled nodes alphabetically.

Shawn

> +
> -- 
> 2.11.0