[PATCH v2 0/8] ARTPEC-6 ARM SoC device tree updates

[PATCH v2 0/8] ARTPEC-6 ARM SoC device tree updates

[Niklas Cassel]

Hello,

Here comes some ARTPEC-6 ARM SoC device tree updates.

Regards,
Niklas

Niklas Cassel (8):
  ARM: dts: artpec: disable Accelerator Coherency Port
  ARM: dts: artpec: use 1 GiB RAM
  ARM: dts: artpec: remove 0x prefix from clkctrl unit address
  ARM: dts: artpec: migrate ethernet to stmmac binding
  ARM: dts: artpec: add and utilize artpec6 pin controller
  ARM: dts: artpec: add and utilize nbpfaxi DMA controllers
  ARM: dts: artpec: add disabled node for PCIe endpoint mode
  ARM: dts: artpec: add node for hardware crypto accelerator

 arch/arm/boot/dts/artpec6-devboard.dts |   3 +-
 arch/arm/boot/dts/artpec6.dtsi         | 163 +++++++++++++++++++++++++++++++--
 2 files changed, 155 insertions(+), 11 deletions(-)

-- 
2.14.2

[PATCH v2 0/8] ARTPEC-6 ARM SoC device tree updates

[Niklas Cassel]

Hello,

Here comes some ARTPEC-6 ARM SoC device tree updates.

Regards,
Niklas

Niklas Cassel (8):
  ARM: dts: artpec: disable Accelerator Coherency Port
  ARM: dts: artpec: use 1 GiB RAM
  ARM: dts: artpec: remove 0x prefix from clkctrl unit address
  ARM: dts: artpec: migrate ethernet to stmmac binding
  ARM: dts: artpec: add and utilize artpec6 pin controller
  ARM: dts: artpec: add and utilize nbpfaxi DMA controllers
  ARM: dts: artpec: add disabled node for PCIe endpoint mode
  ARM: dts: artpec: add node for hardware crypto accelerator

 arch/arm/boot/dts/artpec6-devboard.dts |   3 +-
 arch/arm/boot/dts/artpec6.dtsi         | 163 +++++++++++++++++++++++++++++++--
 2 files changed, 155 insertions(+), 11 deletions(-)

-- 
2.14.2

[PATCH v2 0/8] ARTPEC-6 ARM SoC device tree updates

[Niklas Cassel]

Hello,

Here comes some ARTPEC-6 ARM SoC device tree updates.

Regards,
Niklas

Niklas Cassel (8):
  ARM: dts: artpec: disable Accelerator Coherency Port
  ARM: dts: artpec: use 1 GiB RAM
  ARM: dts: artpec: remove 0x prefix from clkctrl unit address
  ARM: dts: artpec: migrate ethernet to stmmac binding
  ARM: dts: artpec: add and utilize artpec6 pin controller
  ARM: dts: artpec: add and utilize nbpfaxi DMA controllers
  ARM: dts: artpec: add disabled node for PCIe endpoint mode
  ARM: dts: artpec: add node for hardware crypto accelerator

 arch/arm/boot/dts/artpec6-devboard.dts |   3 +-
 arch/arm/boot/dts/artpec6.dtsi         | 163 +++++++++++++++++++++++++++++++--
 2 files changed, 155 insertions(+), 11 deletions(-)

-- 
2.14.2

[PATCH v2 1/8] ARM: dts: artpec: disable Accelerator Coherency Port

[Niklas Cassel]

Accesses via 0x80000000 go through the ACP instead of using the DDR
directly.

Unfortunately the ACP has proven to be the cause of complete system
hangs. Disabling the ACP makes these problems go away.

Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
---
 arch/arm/boot/dts/artpec6.dtsi | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/artpec6.dtsi b/arch/arm/boot/dts/artpec6.dtsi
index 2ed11773048d..d9776a97d8ff 100644
--- a/arch/arm/boot/dts/artpec6.dtsi
+++ b/arch/arm/boot/dts/artpec6.dtsi
@@ -185,8 +185,7 @@
 		#address-cells = <0x1>;
 		#size-cells = <0x1>;
 		ranges;
-		dma-ranges = <0x80000000 0x00000000 0x40000000>;
-		dma-coherent;
+		dma-ranges;
 
 		ethernet: ethernet at f8010000 {
 			clock-names = "phy_ref_clk", "apb_pclk";
-- 
2.14.2

[PATCH v2 1/8] ARM: dts: artpec: disable Accelerator Coherency Port

[Niklas Cassel]

Accesses via 0x80000000 go through the ACP instead of using the DDR
directly.

Unfortunately the ACP has proven to be the cause of complete system
hangs. Disabling the ACP makes these problems go away.

Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
---
 arch/arm/boot/dts/artpec6.dtsi | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/artpec6.dtsi b/arch/arm/boot/dts/artpec6.dtsi
index 2ed11773048d..d9776a97d8ff 100644
--- a/arch/arm/boot/dts/artpec6.dtsi
+++ b/arch/arm/boot/dts/artpec6.dtsi
@@ -185,8 +185,7 @@
 		#address-cells = <0x1>;
 		#size-cells = <0x1>;
 		ranges;
-		dma-ranges = <0x80000000 0x00000000 0x40000000>;
-		dma-coherent;
+		dma-ranges;
 
 		ethernet: ethernet@f8010000 {
 			clock-names = "phy_ref_clk", "apb_pclk";
-- 
2.14.2

[PATCH v2 1/8] ARM: dts: artpec: disable Accelerator Coherency Port

[Niklas Cassel]

Accesses via 0x80000000 go through the ACP instead of using the DDR
directly.

Unfortunately the ACP has proven to be the cause of complete system
hangs. Disabling the ACP makes these problems go away.

Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
---
 arch/arm/boot/dts/artpec6.dtsi | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/artpec6.dtsi b/arch/arm/boot/dts/artpec6.dtsi
index 2ed11773048d..d9776a97d8ff 100644
--- a/arch/arm/boot/dts/artpec6.dtsi
+++ b/arch/arm/boot/dts/artpec6.dtsi
@@ -185,8 +185,7 @@
 		#address-cells = <0x1>;
 		#size-cells = <0x1>;
 		ranges;
-		dma-ranges = <0x80000000 0x00000000 0x40000000>;
-		dma-coherent;
+		dma-ranges;
 
 		ethernet: ethernet@f8010000 {
 			clock-names = "phy_ref_clk", "apb_pclk";
-- 
2.14.2

[PATCH v2 2/8] ARM: dts: artpec: use 1 GiB RAM

[Niklas Cassel]

There has never been an artpec6 devboard produced
with less than 1 GiB RAM.

Increase the default value to 1 GiB RAM, so that we
can netboot with large initramfs without going OOM.

Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
---
 arch/arm/boot/dts/artpec6-devboard.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/artpec6-devboard.dts b/arch/arm/boot/dts/artpec6-devboard.dts
index 9dfe845694cf..502f3de6dc5b 100644
--- a/arch/arm/boot/dts/artpec6-devboard.dts
+++ b/arch/arm/boot/dts/artpec6-devboard.dts
@@ -26,7 +26,7 @@
 
 	memory {
 		device_type = "memory";
-		reg = <0x0 0x10000000>;
+		reg = <0x0 0x40000000>;
 	};
 };
 
-- 
2.14.2

[PATCH v2 2/8] ARM: dts: artpec: use 1 GiB RAM

[Niklas Cassel]

There has never been an artpec6 devboard produced
with less than 1 GiB RAM.

Increase the default value to 1 GiB RAM, so that we
can netboot with large initramfs without going OOM.

Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
---
 arch/arm/boot/dts/artpec6-devboard.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/artpec6-devboard.dts b/arch/arm/boot/dts/artpec6-devboard.dts
index 9dfe845694cf..502f3de6dc5b 100644
--- a/arch/arm/boot/dts/artpec6-devboard.dts
+++ b/arch/arm/boot/dts/artpec6-devboard.dts
@@ -26,7 +26,7 @@
 
 	memory {
 		device_type = "memory";
-		reg = <0x0 0x10000000>;
+		reg = <0x0 0x40000000>;
 	};
 };
 
-- 
2.14.2

[PATCH v2 2/8] ARM: dts: artpec: use 1 GiB RAM

[Niklas Cassel]

There has never been an artpec6 devboard produced
with less than 1 GiB RAM.

Increase the default value to 1 GiB RAM, so that we
can netboot with large initramfs without going OOM.

Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
---
 arch/arm/boot/dts/artpec6-devboard.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/artpec6-devboard.dts b/arch/arm/boot/dts/artpec6-devboard.dts
index 9dfe845694cf..502f3de6dc5b 100644
--- a/arch/arm/boot/dts/artpec6-devboard.dts
+++ b/arch/arm/boot/dts/artpec6-devboard.dts
@@ -26,7 +26,7 @@
 
 	memory {
 		device_type = "memory";
-		reg = <0x0 0x10000000>;
+		reg = <0x0 0x40000000>;
 	};
 };
 
-- 
2.14.2

[PATCH v2 3/8] ARM: dts: artpec: remove 0x prefix from clkctrl unit address

[Niklas Cassel]

Remove 0x prefix from clkctrl unit address.

This silences the following dtc warning:
Warning (unit_address_format):
 Node /clkctrl at 0xf8000000 unit name should not have leading "0x"

Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
---
 arch/arm/boot/dts/artpec6.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/artpec6.dtsi b/arch/arm/boot/dts/artpec6.dtsi
index d9776a97d8ff..f4b39738f1ac 100644
--- a/arch/arm/boot/dts/artpec6.dtsi
+++ b/arch/arm/boot/dts/artpec6.dtsi
@@ -98,7 +98,7 @@
 		clock-frequency = <125000000>;
 	};
 
-	clkctrl: clkctrl at 0xf8000000 {
+	clkctrl: clkctrl at f8000000 {
 		#clock-cells = <1>;
 		compatible = "axis,artpec6-clkctrl";
 		reg = <0xf8000000 0x48>;
-- 
2.14.2

[PATCH v2 3/8] ARM: dts: artpec: remove 0x prefix from clkctrl unit address

[Niklas Cassel]

Remove 0x prefix from clkctrl unit address.

This silences the following dtc warning:
Warning (unit_address_format):
 Node /clkctrl@0xf8000000 unit name should not have leading "0x"

Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
---
 arch/arm/boot/dts/artpec6.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/artpec6.dtsi b/arch/arm/boot/dts/artpec6.dtsi
index d9776a97d8ff..f4b39738f1ac 100644
--- a/arch/arm/boot/dts/artpec6.dtsi
+++ b/arch/arm/boot/dts/artpec6.dtsi
@@ -98,7 +98,7 @@
 		clock-frequency = <125000000>;
 	};
 
-	clkctrl: clkctrl@0xf8000000 {
+	clkctrl: clkctrl@f8000000 {
 		#clock-cells = <1>;
 		compatible = "axis,artpec6-clkctrl";
 		reg = <0xf8000000 0x48>;
-- 
2.14.2

[PATCH v2 3/8] ARM: dts: artpec: remove 0x prefix from clkctrl unit address

[Niklas Cassel]

Remove 0x prefix from clkctrl unit address.

This silences the following dtc warning:
Warning (unit_address_format):
 Node /clkctrl@0xf8000000 unit name should not have leading "0x"

Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
---
 arch/arm/boot/dts/artpec6.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/artpec6.dtsi b/arch/arm/boot/dts/artpec6.dtsi
index d9776a97d8ff..f4b39738f1ac 100644
--- a/arch/arm/boot/dts/artpec6.dtsi
+++ b/arch/arm/boot/dts/artpec6.dtsi
@@ -98,7 +98,7 @@
 		clock-frequency = <125000000>;
 	};
 
-	clkctrl: clkctrl@0xf8000000 {
+	clkctrl: clkctrl@f8000000 {
 		#clock-cells = <1>;
 		compatible = "axis,artpec6-clkctrl";
 		reg = <0xf8000000 0x48>;
-- 
2.14.2

[PATCH v2 4/8] ARM: dts: artpec: migrate ethernet to stmmac binding

[Niklas Cassel]

The snps,dwc-qos-ethernet binding is still supported as a glue layer
in the stmmac driver.
However, since the snps,dwc-qos-ethernet binding is now deprecated,
migrate to stmmac's native binding.

At the same time, enable features supported by the stmmac driver,
such as PTP, LPI, and an additional tx queue.

Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
---
 arch/arm/boot/dts/artpec6-devboard.dts |  1 +
 arch/arm/boot/dts/artpec6.dtsi         | 42 ++++++++++++++++++++++++++++------
 2 files changed, 36 insertions(+), 7 deletions(-)

diff --git a/arch/arm/boot/dts/artpec6-devboard.dts b/arch/arm/boot/dts/artpec6-devboard.dts
index 502f3de6dc5b..d20d95359b28 100644
--- a/arch/arm/boot/dts/artpec6-devboard.dts
+++ b/arch/arm/boot/dts/artpec6-devboard.dts
@@ -59,6 +59,7 @@
 	mdio {
 		#address-cells = <0x1>;
 		#size-cells = <0x0>;
+		compatible = "snps,dwmac-mdio";
 		phy1: phy at 0 {
 			compatible = "ethernet-phy-ieee802.3-c22";
 			device_type = "ethernet-phy";
diff --git a/arch/arm/boot/dts/artpec6.dtsi b/arch/arm/boot/dts/artpec6.dtsi
index f4b39738f1ac..981aecd27b0b 100644
--- a/arch/arm/boot/dts/artpec6.dtsi
+++ b/arch/arm/boot/dts/artpec6.dtsi
@@ -188,19 +188,47 @@
 		dma-ranges;
 
 		ethernet: ethernet at f8010000 {
-			clock-names = "phy_ref_clk", "apb_pclk";
-			clocks = <&eth_phy_ref_clk>,
-				<&clkctrl ARTPEC6_CLK_ETH_ACLK>;
-			compatible = "snps,dwc-qos-ethernet-4.10";
-			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "stmmaceth", "ptp_ref";
+			clocks = <&clkctrl ARTPEC6_CLK_ETH_ACLK>,
+				<&clkctrl ARTPEC6_CLK_PTP_REF>;
+			compatible = "snps,dwmac-4.10a", "snps,dwmac";
+			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq", "eth_lpi";
 			reg = <0xf8010000 0x4000>;
 
-			snps,write-requests = <2>;
-			snps,read-requests = <16>;
+			snps,axi-config = <&stmmac_axi_setup>;
+			snps,mtl-rx-config = <&mtl_rx_setup>;
+			snps,mtl-tx-config = <&mtl_tx_setup>;
+
 			snps,txpbl = <8>;
 			snps,rxpbl = <2>;
+			snps,aal;
+			snps,tso;
 
 			status = "disabled";
+
+			stmmac_axi_setup: stmmac-axi-config {
+				snps,wr_osr_lmt = <1>;
+				snps,rd_osr_lmt = <15>;
+				/* If FB is disabled, the AXI master chooses
+				 * a burst length of any value less than the
+				 * maximum enabled burst length
+				 * (all lesser burst length enables are redundant).
+				 */
+				snps,blen = <0 0 0 0 16 0 0>;
+			};
+
+			mtl_rx_setup: rx-queues-config {
+				snps,rx-queues-to-use = <1>;
+				queue0 {};
+			};
+
+			mtl_tx_setup: tx-queues-config {
+				snps,tx-queues-to-use = <2>;
+				queue0 {};
+				queue1 {};
+			};
 		};
 
 		uart0: serial at f8036000 {
-- 
2.14.2

[PATCH v2 4/8] ARM: dts: artpec: migrate ethernet to stmmac binding

[Niklas Cassel]

The snps,dwc-qos-ethernet binding is still supported as a glue layer
in the stmmac driver.
However, since the snps,dwc-qos-ethernet binding is now deprecated,
migrate to stmmac's native binding.

At the same time, enable features supported by the stmmac driver,
such as PTP, LPI, and an additional tx queue.

Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
---
 arch/arm/boot/dts/artpec6-devboard.dts |  1 +
 arch/arm/boot/dts/artpec6.dtsi         | 42 ++++++++++++++++++++++++++++------
 2 files changed, 36 insertions(+), 7 deletions(-)

diff --git a/arch/arm/boot/dts/artpec6-devboard.dts b/arch/arm/boot/dts/artpec6-devboard.dts
index 502f3de6dc5b..d20d95359b28 100644
--- a/arch/arm/boot/dts/artpec6-devboard.dts
+++ b/arch/arm/boot/dts/artpec6-devboard.dts
@@ -59,6 +59,7 @@
 	mdio {
 		#address-cells = <0x1>;
 		#size-cells = <0x0>;
+		compatible = "snps,dwmac-mdio";
 		phy1: phy@0 {
 			compatible = "ethernet-phy-ieee802.3-c22";
 			device_type = "ethernet-phy";
diff --git a/arch/arm/boot/dts/artpec6.dtsi b/arch/arm/boot/dts/artpec6.dtsi
index f4b39738f1ac..981aecd27b0b 100644
--- a/arch/arm/boot/dts/artpec6.dtsi
+++ b/arch/arm/boot/dts/artpec6.dtsi
@@ -188,19 +188,47 @@
 		dma-ranges;
 
 		ethernet: ethernet@f8010000 {
-			clock-names = "phy_ref_clk", "apb_pclk";
-			clocks = <&eth_phy_ref_clk>,
-				<&clkctrl ARTPEC6_CLK_ETH_ACLK>;
-			compatible = "snps,dwc-qos-ethernet-4.10";
-			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "stmmaceth", "ptp_ref";
+			clocks = <&clkctrl ARTPEC6_CLK_ETH_ACLK>,
+				<&clkctrl ARTPEC6_CLK_PTP_REF>;
+			compatible = "snps,dwmac-4.10a", "snps,dwmac";
+			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq", "eth_lpi";
 			reg = <0xf8010000 0x4000>;
 
-			snps,write-requests = <2>;
-			snps,read-requests = <16>;
+			snps,axi-config = <&stmmac_axi_setup>;
+			snps,mtl-rx-config = <&mtl_rx_setup>;
+			snps,mtl-tx-config = <&mtl_tx_setup>;
+
 			snps,txpbl = <8>;
 			snps,rxpbl = <2>;
+			snps,aal;
+			snps,tso;
 
 			status = "disabled";
+
+			stmmac_axi_setup: stmmac-axi-config {
+				snps,wr_osr_lmt = <1>;
+				snps,rd_osr_lmt = <15>;
+				/* If FB is disabled, the AXI master chooses
+				 * a burst length of any value less than the
+				 * maximum enabled burst length
+				 * (all lesser burst length enables are redundant).
+				 */
+				snps,blen = <0 0 0 0 16 0 0>;
+			};
+
+			mtl_rx_setup: rx-queues-config {
+				snps,rx-queues-to-use = <1>;
+				queue0 {};
+			};
+
+			mtl_tx_setup: tx-queues-config {
+				snps,tx-queues-to-use = <2>;
+				queue0 {};
+				queue1 {};
+			};
 		};
 
 		uart0: serial@f8036000 {
-- 
2.14.2

[PATCH v2 4/8] ARM: dts: artpec: migrate ethernet to stmmac binding

[Niklas Cassel]

The snps,dwc-qos-ethernet binding is still supported as a glue layer
in the stmmac driver.
However, since the snps,dwc-qos-ethernet binding is now deprecated,
migrate to stmmac's native binding.

At the same time, enable features supported by the stmmac driver,
such as PTP, LPI, and an additional tx queue.

Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
---
 arch/arm/boot/dts/artpec6-devboard.dts |  1 +
 arch/arm/boot/dts/artpec6.dtsi         | 42 ++++++++++++++++++++++++++++------
 2 files changed, 36 insertions(+), 7 deletions(-)

diff --git a/arch/arm/boot/dts/artpec6-devboard.dts b/arch/arm/boot/dts/artpec6-devboard.dts
index 502f3de6dc5b..d20d95359b28 100644
--- a/arch/arm/boot/dts/artpec6-devboard.dts
+++ b/arch/arm/boot/dts/artpec6-devboard.dts
@@ -59,6 +59,7 @@
 	mdio {
 		#address-cells = <0x1>;
 		#size-cells = <0x0>;
+		compatible = "snps,dwmac-mdio";
 		phy1: phy@0 {
 			compatible = "ethernet-phy-ieee802.3-c22";
 			device_type = "ethernet-phy";
diff --git a/arch/arm/boot/dts/artpec6.dtsi b/arch/arm/boot/dts/artpec6.dtsi
index f4b39738f1ac..981aecd27b0b 100644
--- a/arch/arm/boot/dts/artpec6.dtsi
+++ b/arch/arm/boot/dts/artpec6.dtsi
@@ -188,19 +188,47 @@
 		dma-ranges;
 
 		ethernet: ethernet@f8010000 {
-			clock-names = "phy_ref_clk", "apb_pclk";
-			clocks = <&eth_phy_ref_clk>,
-				<&clkctrl ARTPEC6_CLK_ETH_ACLK>;
-			compatible = "snps,dwc-qos-ethernet-4.10";
-			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "stmmaceth", "ptp_ref";
+			clocks = <&clkctrl ARTPEC6_CLK_ETH_ACLK>,
+				<&clkctrl ARTPEC6_CLK_PTP_REF>;
+			compatible = "snps,dwmac-4.10a", "snps,dwmac";
+			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq", "eth_lpi";
 			reg = <0xf8010000 0x4000>;
 
-			snps,write-requests = <2>;
-			snps,read-requests = <16>;
+			snps,axi-config = <&stmmac_axi_setup>;
+			snps,mtl-rx-config = <&mtl_rx_setup>;
+			snps,mtl-tx-config = <&mtl_tx_setup>;
+
 			snps,txpbl = <8>;
 			snps,rxpbl = <2>;
+			snps,aal;
+			snps,tso;
 
 			status = "disabled";
+
+			stmmac_axi_setup: stmmac-axi-config {
+				snps,wr_osr_lmt = <1>;
+				snps,rd_osr_lmt = <15>;
+				/* If FB is disabled, the AXI master chooses
+				 * a burst length of any value less than the
+				 * maximum enabled burst length
+				 * (all lesser burst length enables are redundant).
+				 */
+				snps,blen = <0 0 0 0 16 0 0>;
+			};
+
+			mtl_rx_setup: rx-queues-config {
+				snps,rx-queues-to-use = <1>;
+				queue0 {};
+			};
+
+			mtl_tx_setup: tx-queues-config {
+				snps,tx-queues-to-use = <2>;
+				queue0 {};
+				queue1 {};
+			};
 		};
 
 		uart0: serial@f8036000 {
-- 
2.14.2

[PATCH v2 5/8] ARM: dts: artpec: add and utilize artpec6 pin controller

[Niklas Cassel]

Add node for the pin controller used in the artpec6 SoC,
and start using it for the exising UARTs.

Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
---
 arch/arm/boot/dts/artpec6.dtsi | 34 ++++++++++++++++++++++++++++++++++
 1 file changed, 34 insertions(+)

diff --git a/arch/arm/boot/dts/artpec6.dtsi b/arch/arm/boot/dts/artpec6.dtsi
index 981aecd27b0b..7a6d8f39823a 100644
--- a/arch/arm/boot/dts/artpec6.dtsi
+++ b/arch/arm/boot/dts/artpec6.dtsi
@@ -180,6 +180,32 @@
 		status = "disabled";
 	};
 
+	pinctrl: pinctrl at f801d000 {
+		compatible = "axis,artpec6-pinctrl";
+		reg = <0xf801d000 0x400>;
+
+		pinctrl_uart0: uart0grp {
+			function = "uart0";
+			groups = "uart0grp2";
+			bias-pull-up;
+		};
+		pinctrl_uart1: uart1grp {
+			function = "uart1";
+			groups = "uart1grp0";
+			bias-pull-up;
+		};
+		pinctrl_uart2: uart2grp {
+			function = "uart2";
+			groups = "uart2grp1";
+			bias-pull-up;
+		};
+		pinctrl_uart3: uart3grp {
+			function = "uart3";
+			groups = "uart3grp0";
+			bias-pull-up;
+		};
+	};
+
 	amba at 0 {
 		compatible = "simple-bus";
 		#address-cells = <0x1>;
@@ -238,6 +264,8 @@
 			clocks = <&clkctrl ARTPEC6_CLK_UART_REFCLK>,
 				<&clkctrl ARTPEC6_CLK_UART_PCLK>;
 			clock-names = "uart_clk", "apb_pclk";
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_uart0>;
 			status = "disabled";
 		};
 		uart1: serial at f8037000 {
@@ -247,6 +275,8 @@
 			clocks = <&clkctrl ARTPEC6_CLK_UART_REFCLK>,
 				<&clkctrl ARTPEC6_CLK_UART_PCLK>;
 			clock-names = "uart_clk", "apb_pclk";
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_uart1>;
 			status = "disabled";
 		};
 		uart2: serial at f8038000 {
@@ -256,6 +286,8 @@
 			clocks = <&clkctrl ARTPEC6_CLK_UART_REFCLK>,
 				<&clkctrl ARTPEC6_CLK_UART_PCLK>;
 			clock-names = "uart_clk", "apb_pclk";
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_uart2>;
 			status = "disabled";
 		};
 		uart3: serial at f8039000 {
@@ -265,6 +297,8 @@
 			clocks = <&clkctrl ARTPEC6_CLK_UART_REFCLK>,
 				<&clkctrl ARTPEC6_CLK_UART_PCLK>;
 			clock-names = "uart_clk", "apb_pclk";
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_uart3>;
 			status = "disabled";
 		};
 	};
-- 
2.14.2

[PATCH v2 5/8] ARM: dts: artpec: add and utilize artpec6 pin controller

[Niklas Cassel]

Add node for the pin controller used in the artpec6 SoC,
and start using it for the exising UARTs.

Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
---
 arch/arm/boot/dts/artpec6.dtsi | 34 ++++++++++++++++++++++++++++++++++
 1 file changed, 34 insertions(+)

diff --git a/arch/arm/boot/dts/artpec6.dtsi b/arch/arm/boot/dts/artpec6.dtsi
index 981aecd27b0b..7a6d8f39823a 100644
--- a/arch/arm/boot/dts/artpec6.dtsi
+++ b/arch/arm/boot/dts/artpec6.dtsi
@@ -180,6 +180,32 @@
 		status = "disabled";
 	};
 
+	pinctrl: pinctrl@f801d000 {
+		compatible = "axis,artpec6-pinctrl";
+		reg = <0xf801d000 0x400>;
+
+		pinctrl_uart0: uart0grp {
+			function = "uart0";
+			groups = "uart0grp2";
+			bias-pull-up;
+		};
+		pinctrl_uart1: uart1grp {
+			function = "uart1";
+			groups = "uart1grp0";
+			bias-pull-up;
+		};
+		pinctrl_uart2: uart2grp {
+			function = "uart2";
+			groups = "uart2grp1";
+			bias-pull-up;
+		};
+		pinctrl_uart3: uart3grp {
+			function = "uart3";
+			groups = "uart3grp0";
+			bias-pull-up;
+		};
+	};
+
 	amba@0 {
 		compatible = "simple-bus";
 		#address-cells = <0x1>;
@@ -238,6 +264,8 @@
 			clocks = <&clkctrl ARTPEC6_CLK_UART_REFCLK>,
 				<&clkctrl ARTPEC6_CLK_UART_PCLK>;
 			clock-names = "uart_clk", "apb_pclk";
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_uart0>;
 			status = "disabled";
 		};
 		uart1: serial@f8037000 {
@@ -247,6 +275,8 @@
 			clocks = <&clkctrl ARTPEC6_CLK_UART_REFCLK>,
 				<&clkctrl ARTPEC6_CLK_UART_PCLK>;
 			clock-names = "uart_clk", "apb_pclk";
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_uart1>;
 			status = "disabled";
 		};
 		uart2: serial@f8038000 {
@@ -256,6 +286,8 @@
 			clocks = <&clkctrl ARTPEC6_CLK_UART_REFCLK>,
 				<&clkctrl ARTPEC6_CLK_UART_PCLK>;
 			clock-names = "uart_clk", "apb_pclk";
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_uart2>;
 			status = "disabled";
 		};
 		uart3: serial@f8039000 {
@@ -265,6 +297,8 @@
 			clocks = <&clkctrl ARTPEC6_CLK_UART_REFCLK>,
 				<&clkctrl ARTPEC6_CLK_UART_PCLK>;
 			clock-names = "uart_clk", "apb_pclk";
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_uart3>;
 			status = "disabled";
 		};
 	};
-- 
2.14.2

[PATCH v2 5/8] ARM: dts: artpec: add and utilize artpec6 pin controller

[Niklas Cassel]

Add node for the pin controller used in the artpec6 SoC,
and start using it for the exising UARTs.

Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
---
 arch/arm/boot/dts/artpec6.dtsi | 34 ++++++++++++++++++++++++++++++++++
 1 file changed, 34 insertions(+)

diff --git a/arch/arm/boot/dts/artpec6.dtsi b/arch/arm/boot/dts/artpec6.dtsi
index 981aecd27b0b..7a6d8f39823a 100644
--- a/arch/arm/boot/dts/artpec6.dtsi
+++ b/arch/arm/boot/dts/artpec6.dtsi
@@ -180,6 +180,32 @@
 		status = "disabled";
 	};
 
+	pinctrl: pinctrl@f801d000 {
+		compatible = "axis,artpec6-pinctrl";
+		reg = <0xf801d000 0x400>;
+
+		pinctrl_uart0: uart0grp {
+			function = "uart0";
+			groups = "uart0grp2";
+			bias-pull-up;
+		};
+		pinctrl_uart1: uart1grp {
+			function = "uart1";
+			groups = "uart1grp0";
+			bias-pull-up;
+		};
+		pinctrl_uart2: uart2grp {
+			function = "uart2";
+			groups = "uart2grp1";
+			bias-pull-up;
+		};
+		pinctrl_uart3: uart3grp {
+			function = "uart3";
+			groups = "uart3grp0";
+			bias-pull-up;
+		};
+	};
+
 	amba@0 {
 		compatible = "simple-bus";
 		#address-cells = <0x1>;
@@ -238,6 +264,8 @@
 			clocks = <&clkctrl ARTPEC6_CLK_UART_REFCLK>,
 				<&clkctrl ARTPEC6_CLK_UART_PCLK>;
 			clock-names = "uart_clk", "apb_pclk";
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_uart0>;
 			status = "disabled";
 		};
 		uart1: serial@f8037000 {
@@ -247,6 +275,8 @@
 			clocks = <&clkctrl ARTPEC6_CLK_UART_REFCLK>,
 				<&clkctrl ARTPEC6_CLK_UART_PCLK>;
 			clock-names = "uart_clk", "apb_pclk";
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_uart1>;
 			status = "disabled";
 		};
 		uart2: serial@f8038000 {
@@ -256,6 +286,8 @@
 			clocks = <&clkctrl ARTPEC6_CLK_UART_REFCLK>,
 				<&clkctrl ARTPEC6_CLK_UART_PCLK>;
 			clock-names = "uart_clk", "apb_pclk";
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_uart2>;
 			status = "disabled";
 		};
 		uart3: serial@f8039000 {
@@ -265,6 +297,8 @@
 			clocks = <&clkctrl ARTPEC6_CLK_UART_REFCLK>,
 				<&clkctrl ARTPEC6_CLK_UART_PCLK>;
 			clock-names = "uart_clk", "apb_pclk";
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_uart3>;
 			status = "disabled";
 		};
 	};
-- 
2.14.2

[PATCH v2 6/8] ARM: dts: artpec: add and utilize nbpfaxi DMA controllers

[Niklas Cassel]

Add nodes for the nbpfaxi DMA controllers used in the artpec6 SoC,
and start using them for the exising UARTs.

Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
---
 arch/arm/boot/dts/artpec6.dtsi | 58 ++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 58 insertions(+)

diff --git a/arch/arm/boot/dts/artpec6.dtsi b/arch/arm/boot/dts/artpec6.dtsi
index 7a6d8f39823a..1c46df0c03ce 100644
--- a/arch/arm/boot/dts/artpec6.dtsi
+++ b/arch/arm/boot/dts/artpec6.dtsi
@@ -41,6 +41,7 @@
  */
 
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/dma/nbpfaxi.h>
 #include <dt-bindings/clock/axis,artpec6-clkctrl.h>
 #include "skeleton.dtsi"
 
@@ -213,6 +214,51 @@
 		ranges;
 		dma-ranges;
 
+		dma0: dma at f8019000 {
+			compatible = "renesas,nbpfaxi64dmac8b16";
+			reg = <0xf8019000 0x400>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>, /* error */
+				     <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "error",
+					  "ch0", "ch1", "ch2", "ch3",
+					  "ch4", "ch5", "ch6", "ch7",
+					  "ch8", "ch9", "ch10", "ch12",
+					  "ch12", "ch13", "ch14", "ch15";
+			clocks = <&clkctrl ARTPEC6_CLK_DMA_ACLK>;
+			#dma-cells = <2>;
+			dma-channels = <8>;
+			dma-requests = <8>;
+		};
+		dma1: dma at f8019400 {
+			compatible = "renesas,nbpfaxi64dmac8b16";
+			reg = <0xf8019400 0x400>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>, /* error */
+				     <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "error",
+					  "ch0", "ch1", "ch2", "ch3",
+					  "ch4", "ch5", "ch6", "ch7",
+					  "ch8", "ch9", "ch10", "ch12",
+					  "ch12", "ch13", "ch14", "ch15";
+			clocks = <&clkctrl ARTPEC6_CLK_DMA_ACLK>;
+			#dma-cells = <2>;
+			dma-channels = <8>;
+			dma-requests = <8>;
+		};
+
 		ethernet: ethernet at f8010000 {
 			clock-names = "stmmaceth", "ptp_ref";
 			clocks = <&clkctrl ARTPEC6_CLK_ETH_ACLK>,
@@ -266,6 +312,9 @@
 			clock-names = "uart_clk", "apb_pclk";
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart0>;
+			dmas = <&dma0 4 (NBPF_SLAVE_RQ_HIGH | NBPF_SLAVE_RQ_LEVEL)>,
+			       <&dma0 5 (NBPF_SLAVE_RQ_HIGH | NBPF_SLAVE_RQ_LEVEL)>;
+			dma-names = "rx", "tx";
 			status = "disabled";
 		};
 		uart1: serial at f8037000 {
@@ -277,6 +326,9 @@
 			clock-names = "uart_clk", "apb_pclk";
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart1>;
+			dmas = <&dma0 6 (NBPF_SLAVE_RQ_HIGH | NBPF_SLAVE_RQ_LEVEL)>,
+			       <&dma0 7 (NBPF_SLAVE_RQ_HIGH | NBPF_SLAVE_RQ_LEVEL)>;
+			dma-names = "rx", "tx";
 			status = "disabled";
 		};
 		uart2: serial at f8038000 {
@@ -288,6 +340,9 @@
 			clock-names = "uart_clk", "apb_pclk";
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart2>;
+			dmas = <&dma1 0 (NBPF_SLAVE_RQ_HIGH | NBPF_SLAVE_RQ_LEVEL)>,
+			       <&dma1 1 (NBPF_SLAVE_RQ_HIGH | NBPF_SLAVE_RQ_LEVEL)>;
+			dma-names = "rx", "tx";
 			status = "disabled";
 		};
 		uart3: serial at f8039000 {
@@ -299,6 +354,9 @@
 			clock-names = "uart_clk", "apb_pclk";
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart3>;
+			dmas = <&dma1 2 (NBPF_SLAVE_RQ_HIGH | NBPF_SLAVE_RQ_LEVEL)>,
+			       <&dma1 3 (NBPF_SLAVE_RQ_HIGH | NBPF_SLAVE_RQ_LEVEL)>;
+			dma-names = "rx", "tx";
 			status = "disabled";
 		};
 	};
-- 
2.14.2

[PATCH v2 6/8] ARM: dts: artpec: add and utilize nbpfaxi DMA controllers

[Niklas Cassel]

Add nodes for the nbpfaxi DMA controllers used in the artpec6 SoC,
and start using them for the exising UARTs.

Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
---
 arch/arm/boot/dts/artpec6.dtsi | 58 ++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 58 insertions(+)

diff --git a/arch/arm/boot/dts/artpec6.dtsi b/arch/arm/boot/dts/artpec6.dtsi
index 7a6d8f39823a..1c46df0c03ce 100644
--- a/arch/arm/boot/dts/artpec6.dtsi
+++ b/arch/arm/boot/dts/artpec6.dtsi
@@ -41,6 +41,7 @@
  */
 
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/dma/nbpfaxi.h>
 #include <dt-bindings/clock/axis,artpec6-clkctrl.h>
 #include "skeleton.dtsi"
 
@@ -213,6 +214,51 @@
 		ranges;
 		dma-ranges;
 
+		dma0: dma@f8019000 {
+			compatible = "renesas,nbpfaxi64dmac8b16";
+			reg = <0xf8019000 0x400>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>, /* error */
+				     <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "error",
+					  "ch0", "ch1", "ch2", "ch3",
+					  "ch4", "ch5", "ch6", "ch7",
+					  "ch8", "ch9", "ch10", "ch12",
+					  "ch12", "ch13", "ch14", "ch15";
+			clocks = <&clkctrl ARTPEC6_CLK_DMA_ACLK>;
+			#dma-cells = <2>;
+			dma-channels = <8>;
+			dma-requests = <8>;
+		};
+		dma1: dma@f8019400 {
+			compatible = "renesas,nbpfaxi64dmac8b16";
+			reg = <0xf8019400 0x400>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>, /* error */
+				     <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "error",
+					  "ch0", "ch1", "ch2", "ch3",
+					  "ch4", "ch5", "ch6", "ch7",
+					  "ch8", "ch9", "ch10", "ch12",
+					  "ch12", "ch13", "ch14", "ch15";
+			clocks = <&clkctrl ARTPEC6_CLK_DMA_ACLK>;
+			#dma-cells = <2>;
+			dma-channels = <8>;
+			dma-requests = <8>;
+		};
+
 		ethernet: ethernet@f8010000 {
 			clock-names = "stmmaceth", "ptp_ref";
 			clocks = <&clkctrl ARTPEC6_CLK_ETH_ACLK>,
@@ -266,6 +312,9 @@
 			clock-names = "uart_clk", "apb_pclk";
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart0>;
+			dmas = <&dma0 4 (NBPF_SLAVE_RQ_HIGH | NBPF_SLAVE_RQ_LEVEL)>,
+			       <&dma0 5 (NBPF_SLAVE_RQ_HIGH | NBPF_SLAVE_RQ_LEVEL)>;
+			dma-names = "rx", "tx";
 			status = "disabled";
 		};
 		uart1: serial@f8037000 {
@@ -277,6 +326,9 @@
 			clock-names = "uart_clk", "apb_pclk";
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart1>;
+			dmas = <&dma0 6 (NBPF_SLAVE_RQ_HIGH | NBPF_SLAVE_RQ_LEVEL)>,
+			       <&dma0 7 (NBPF_SLAVE_RQ_HIGH | NBPF_SLAVE_RQ_LEVEL)>;
+			dma-names = "rx", "tx";
 			status = "disabled";
 		};
 		uart2: serial@f8038000 {
@@ -288,6 +340,9 @@
 			clock-names = "uart_clk", "apb_pclk";
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart2>;
+			dmas = <&dma1 0 (NBPF_SLAVE_RQ_HIGH | NBPF_SLAVE_RQ_LEVEL)>,
+			       <&dma1 1 (NBPF_SLAVE_RQ_HIGH | NBPF_SLAVE_RQ_LEVEL)>;
+			dma-names = "rx", "tx";
 			status = "disabled";
 		};
 		uart3: serial@f8039000 {
@@ -299,6 +354,9 @@
 			clock-names = "uart_clk", "apb_pclk";
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart3>;
+			dmas = <&dma1 2 (NBPF_SLAVE_RQ_HIGH | NBPF_SLAVE_RQ_LEVEL)>,
+			       <&dma1 3 (NBPF_SLAVE_RQ_HIGH | NBPF_SLAVE_RQ_LEVEL)>;
+			dma-names = "rx", "tx";
 			status = "disabled";
 		};
 	};
-- 
2.14.2

[PATCH v2 6/8] ARM: dts: artpec: add and utilize nbpfaxi DMA controllers

[Niklas Cassel]

Add nodes for the nbpfaxi DMA controllers used in the artpec6 SoC,
and start using them for the exising UARTs.

Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
---
 arch/arm/boot/dts/artpec6.dtsi | 58 ++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 58 insertions(+)

diff --git a/arch/arm/boot/dts/artpec6.dtsi b/arch/arm/boot/dts/artpec6.dtsi
index 7a6d8f39823a..1c46df0c03ce 100644
--- a/arch/arm/boot/dts/artpec6.dtsi
+++ b/arch/arm/boot/dts/artpec6.dtsi
@@ -41,6 +41,7 @@
  */
 
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/dma/nbpfaxi.h>
 #include <dt-bindings/clock/axis,artpec6-clkctrl.h>
 #include "skeleton.dtsi"
 
@@ -213,6 +214,51 @@
 		ranges;
 		dma-ranges;
 
+		dma0: dma@f8019000 {
+			compatible = "renesas,nbpfaxi64dmac8b16";
+			reg = <0xf8019000 0x400>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>, /* error */
+				     <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "error",
+					  "ch0", "ch1", "ch2", "ch3",
+					  "ch4", "ch5", "ch6", "ch7",
+					  "ch8", "ch9", "ch10", "ch12",
+					  "ch12", "ch13", "ch14", "ch15";
+			clocks = <&clkctrl ARTPEC6_CLK_DMA_ACLK>;
+			#dma-cells = <2>;
+			dma-channels = <8>;
+			dma-requests = <8>;
+		};
+		dma1: dma@f8019400 {
+			compatible = "renesas,nbpfaxi64dmac8b16";
+			reg = <0xf8019400 0x400>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>, /* error */
+				     <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "error",
+					  "ch0", "ch1", "ch2", "ch3",
+					  "ch4", "ch5", "ch6", "ch7",
+					  "ch8", "ch9", "ch10", "ch12",
+					  "ch12", "ch13", "ch14", "ch15";
+			clocks = <&clkctrl ARTPEC6_CLK_DMA_ACLK>;
+			#dma-cells = <2>;
+			dma-channels = <8>;
+			dma-requests = <8>;
+		};
+
 		ethernet: ethernet@f8010000 {
 			clock-names = "stmmaceth", "ptp_ref";
 			clocks = <&clkctrl ARTPEC6_CLK_ETH_ACLK>,
@@ -266,6 +312,9 @@
 			clock-names = "uart_clk", "apb_pclk";
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart0>;
+			dmas = <&dma0 4 (NBPF_SLAVE_RQ_HIGH | NBPF_SLAVE_RQ_LEVEL)>,
+			       <&dma0 5 (NBPF_SLAVE_RQ_HIGH | NBPF_SLAVE_RQ_LEVEL)>;
+			dma-names = "rx", "tx";
 			status = "disabled";
 		};
 		uart1: serial@f8037000 {
@@ -277,6 +326,9 @@
 			clock-names = "uart_clk", "apb_pclk";
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart1>;
+			dmas = <&dma0 6 (NBPF_SLAVE_RQ_HIGH | NBPF_SLAVE_RQ_LEVEL)>,
+			       <&dma0 7 (NBPF_SLAVE_RQ_HIGH | NBPF_SLAVE_RQ_LEVEL)>;
+			dma-names = "rx", "tx";
 			status = "disabled";
 		};
 		uart2: serial@f8038000 {
@@ -288,6 +340,9 @@
 			clock-names = "uart_clk", "apb_pclk";
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart2>;
+			dmas = <&dma1 0 (NBPF_SLAVE_RQ_HIGH | NBPF_SLAVE_RQ_LEVEL)>,
+			       <&dma1 1 (NBPF_SLAVE_RQ_HIGH | NBPF_SLAVE_RQ_LEVEL)>;
+			dma-names = "rx", "tx";
 			status = "disabled";
 		};
 		uart3: serial@f8039000 {
@@ -299,6 +354,9 @@
 			clock-names = "uart_clk", "apb_pclk";
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart3>;
+			dmas = <&dma1 2 (NBPF_SLAVE_RQ_HIGH | NBPF_SLAVE_RQ_LEVEL)>,
+			       <&dma1 3 (NBPF_SLAVE_RQ_HIGH | NBPF_SLAVE_RQ_LEVEL)>;
+			dma-names = "rx", "tx";
 			status = "disabled";
 		};
 	};
-- 
2.14.2

[PATCH v2 7/8] ARM: dts: artpec: add disabled node for PCIe endpoint mode

[Niklas Cassel]

The PCIe controller in the artpec6 SoC supports both root complex and
endpoint mode, however, the controller can only be used in one of the
modes.

Both pci nodes are disabled by default. A DTS file can enable one of
them, depending on what mode it wants to run.

Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
---
Changes since V1:
removed unused properties "interrupts" and "interrupt-names"

 arch/arm/boot/dts/artpec6.dtsi | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)

diff --git a/arch/arm/boot/dts/artpec6.dtsi b/arch/arm/boot/dts/artpec6.dtsi
index 1c46df0c03ce..b7720be8afb1 100644
--- a/arch/arm/boot/dts/artpec6.dtsi
+++ b/arch/arm/boot/dts/artpec6.dtsi
@@ -154,6 +154,10 @@
 		interrupt-affinity = <&cpu0>, <&cpu1>;
 	};
 
+	/*
+	 * Both pci nodes cannot be enabled at the same time,
+	 * leave the unwanted node as disabled.
+	 */
 	pcie: pcie at f8050000 {
 		compatible = "axis,artpec6-pcie", "snps,dw-pcie";
 		reg = <0xf8050000 0x2000
@@ -181,6 +185,20 @@
 		status = "disabled";
 	};
 
+	pcie_ep: pcie_ep@f8050000 {
+		compatible = "axis,artpec6-pcie-ep", "snps,dw-pcie";
+		reg = <0xf8050000 0x2000
+		       0xf8051000 0x2000
+		       0xf8040000 0x1000
+		       0xc0000000 0x20000000>;
+		reg-names = "dbi", "dbi2", "phy", "addr_space";
+		num-ib-windows = <6>;
+		num-ob-windows = <2>;
+		num-lanes = <2>;
+		axis,syscon-pcie = <&syscon>;
+		status = "disabled";
+	};
+
 	pinctrl: pinctrl at f801d000 {
 		compatible = "axis,artpec6-pinctrl";
 		reg = <0xf801d000 0x400>;
-- 
2.14.2

[PATCH v2 7/8] ARM: dts: artpec: add disabled node for PCIe endpoint mode

[Niklas Cassel]

The PCIe controller in the artpec6 SoC supports both root complex and
endpoint mode, however, the controller can only be used in one of the
modes.

Both pci nodes are disabled by default. A DTS file can enable one of
them, depending on what mode it wants to run.

Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
---
Changes since V1:
removed unused properties "interrupts" and "interrupt-names"

 arch/arm/boot/dts/artpec6.dtsi | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)

diff --git a/arch/arm/boot/dts/artpec6.dtsi b/arch/arm/boot/dts/artpec6.dtsi
index 1c46df0c03ce..b7720be8afb1 100644
--- a/arch/arm/boot/dts/artpec6.dtsi
+++ b/arch/arm/boot/dts/artpec6.dtsi
@@ -154,6 +154,10 @@
 		interrupt-affinity = <&cpu0>, <&cpu1>;
 	};
 
+	/*
+	 * Both pci nodes cannot be enabled at the same time,
+	 * leave the unwanted node as disabled.
+	 */
 	pcie: pcie@f8050000 {
 		compatible = "axis,artpec6-pcie", "snps,dw-pcie";
 		reg = <0xf8050000 0x2000
@@ -181,6 +185,20 @@
 		status = "disabled";
 	};
 
+	pcie_ep: pcie_ep@f8050000 {
+		compatible = "axis,artpec6-pcie-ep", "snps,dw-pcie";
+		reg = <0xf8050000 0x2000
+		       0xf8051000 0x2000
+		       0xf8040000 0x1000
+		       0xc0000000 0x20000000>;
+		reg-names = "dbi", "dbi2", "phy", "addr_space";
+		num-ib-windows = <6>;
+		num-ob-windows = <2>;
+		num-lanes = <2>;
+		axis,syscon-pcie = <&syscon>;
+		status = "disabled";
+	};
+
 	pinctrl: pinctrl@f801d000 {
 		compatible = "axis,artpec6-pinctrl";
 		reg = <0xf801d000 0x400>;
-- 
2.14.2

[PATCH v2 7/8] ARM: dts: artpec: add disabled node for PCIe endpoint mode

[Niklas Cassel]

The PCIe controller in the artpec6 SoC supports both root complex and
endpoint mode, however, the controller can only be used in one of the
modes.

Both pci nodes are disabled by default. A DTS file can enable one of
them, depending on what mode it wants to run.

Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
---
Changes since V1:
removed unused properties "interrupts" and "interrupt-names"

 arch/arm/boot/dts/artpec6.dtsi | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)

diff --git a/arch/arm/boot/dts/artpec6.dtsi b/arch/arm/boot/dts/artpec6.dtsi
index 1c46df0c03ce..b7720be8afb1 100644
--- a/arch/arm/boot/dts/artpec6.dtsi
+++ b/arch/arm/boot/dts/artpec6.dtsi
@@ -154,6 +154,10 @@
 		interrupt-affinity = <&cpu0>, <&cpu1>;
 	};
 
+	/*
+	 * Both pci nodes cannot be enabled at the same time,
+	 * leave the unwanted node as disabled.
+	 */
 	pcie: pcie@f8050000 {
 		compatible = "axis,artpec6-pcie", "snps,dw-pcie";
 		reg = <0xf8050000 0x2000
@@ -181,6 +185,20 @@
 		status = "disabled";
 	};
 
+	pcie_ep: pcie_ep@f8050000 {
+		compatible = "axis,artpec6-pcie-ep", "snps,dw-pcie";
+		reg = <0xf8050000 0x2000
+		       0xf8051000 0x2000
+		       0xf8040000 0x1000
+		       0xc0000000 0x20000000>;
+		reg-names = "dbi", "dbi2", "phy", "addr_space";
+		num-ib-windows = <6>;
+		num-ob-windows = <2>;
+		num-lanes = <2>;
+		axis,syscon-pcie = <&syscon>;
+		status = "disabled";
+	};
+
 	pinctrl: pinctrl@f801d000 {
 		compatible = "axis,artpec6-pinctrl";
 		reg = <0xf801d000 0x400>;
-- 
2.14.2

[PATCH v2 8/8] ARM: dts: artpec: add node for hardware crypto accelerator

[Niklas Cassel]

Add node for the hardware crypto acceleration used in the artpec6 SoC.

Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
---
 arch/arm/boot/dts/artpec6.dtsi | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/arch/arm/boot/dts/artpec6.dtsi b/arch/arm/boot/dts/artpec6.dtsi
index b7720be8afb1..3e4115c2cd75 100644
--- a/arch/arm/boot/dts/artpec6.dtsi
+++ b/arch/arm/boot/dts/artpec6.dtsi
@@ -232,6 +232,12 @@
 		ranges;
 		dma-ranges;
 
+		crypto at f4264000 {
+			compatible = "axis,artpec6-crypto";
+			reg = <0xf4264000 0x4000>;
+			interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
 		dma0: dma at f8019000 {
 			compatible = "renesas,nbpfaxi64dmac8b16";
 			reg = <0xf8019000 0x400>;
-- 
2.14.2

[PATCH v2 8/8] ARM: dts: artpec: add node for hardware crypto accelerator

[Niklas Cassel]

Add node for the hardware crypto acceleration used in the artpec6 SoC.

Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
---
 arch/arm/boot/dts/artpec6.dtsi | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/arch/arm/boot/dts/artpec6.dtsi b/arch/arm/boot/dts/artpec6.dtsi
index b7720be8afb1..3e4115c2cd75 100644
--- a/arch/arm/boot/dts/artpec6.dtsi
+++ b/arch/arm/boot/dts/artpec6.dtsi
@@ -232,6 +232,12 @@
 		ranges;
 		dma-ranges;
 
+		crypto@f4264000 {
+			compatible = "axis,artpec6-crypto";
+			reg = <0xf4264000 0x4000>;
+			interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
 		dma0: dma@f8019000 {
 			compatible = "renesas,nbpfaxi64dmac8b16";
 			reg = <0xf8019000 0x400>;
-- 
2.14.2

[PATCH v2 8/8] ARM: dts: artpec: add node for hardware crypto accelerator

[Niklas Cassel]

Add node for the hardware crypto acceleration used in the artpec6 SoC.

Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
---
 arch/arm/boot/dts/artpec6.dtsi | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/arch/arm/boot/dts/artpec6.dtsi b/arch/arm/boot/dts/artpec6.dtsi
index b7720be8afb1..3e4115c2cd75 100644
--- a/arch/arm/boot/dts/artpec6.dtsi
+++ b/arch/arm/boot/dts/artpec6.dtsi
@@ -232,6 +232,12 @@
 		ranges;
 		dma-ranges;
 
+		crypto@f4264000 {
+			compatible = "axis,artpec6-crypto";
+			reg = <0xf4264000 0x4000>;
+			interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
 		dma0: dma@f8019000 {
 			compatible = "renesas,nbpfaxi64dmac8b16";
 			reg = <0xf8019000 0x400>;
-- 
2.14.2

[PATCH v2 0/8] ARTPEC-6 ARM SoC device tree updates

[Arnd Bergmann]

On Wed, Feb 21, 2018 at 9:59 AM, Niklas Cassel <niklas.cassel@axis.com> wrote:
> Hello,
>
> Here comes some ARTPEC-6 ARM SoC device tree updates.
>
> Niklas Cassel (8):
>   ARM: dts: artpec: disable Accelerator Coherency Port
>   ARM: dts: artpec: use 1 GiB RAM
>   ARM: dts: artpec: remove 0x prefix from clkctrl unit address
>   ARM: dts: artpec: migrate ethernet to stmmac binding
>   ARM: dts: artpec: add and utilize artpec6 pin controller
>   ARM: dts: artpec: add and utilize nbpfaxi DMA controllers
>   ARM: dts: artpec: add disabled node for PCIe endpoint mode
>   ARM: dts: artpec: add node for hardware crypto accelerator

For a series eight patches, a pull request would save me some work, but
I applied it anyway.

Are you sure that the first three patches shouldn't be applied to stable
backports?

     Arnd

Re: [PATCH v2 0/8] ARTPEC-6 ARM SoC device tree updates

[Arnd Bergmann]

On Wed, Feb 21, 2018 at 9:59 AM, Niklas Cassel <niklas.cassel@axis.com> wrote:
> Hello,
>
> Here comes some ARTPEC-6 ARM SoC device tree updates.
>
> Niklas Cassel (8):
>   ARM: dts: artpec: disable Accelerator Coherency Port
>   ARM: dts: artpec: use 1 GiB RAM
>   ARM: dts: artpec: remove 0x prefix from clkctrl unit address
>   ARM: dts: artpec: migrate ethernet to stmmac binding
>   ARM: dts: artpec: add and utilize artpec6 pin controller
>   ARM: dts: artpec: add and utilize nbpfaxi DMA controllers
>   ARM: dts: artpec: add disabled node for PCIe endpoint mode
>   ARM: dts: artpec: add node for hardware crypto accelerator

For a series eight patches, a pull request would save me some work, but
I applied it anyway.

Are you sure that the first three patches shouldn't be applied to stable
backports?

     Arnd

[PATCH v2 0/8] ARTPEC-6 ARM SoC device tree updates

[Niklas Cassel]

On Tue, Mar 06, 2018 at 05:45:30PM +0100, Arnd Bergmann wrote:
> On Wed, Feb 21, 2018 at 9:59 AM, Niklas Cassel <niklas.cassel@axis.com> wrote:
> > Hello,
> >
> > Here comes some ARTPEC-6 ARM SoC device tree updates.
> >
> > Niklas Cassel (8):
> >   ARM: dts: artpec: disable Accelerator Coherency Port
> >   ARM: dts: artpec: use 1 GiB RAM
> >   ARM: dts: artpec: remove 0x prefix from clkctrl unit address
> >   ARM: dts: artpec: migrate ethernet to stmmac binding
> >   ARM: dts: artpec: add and utilize artpec6 pin controller
> >   ARM: dts: artpec: add and utilize nbpfaxi DMA controllers
> >   ARM: dts: artpec: add disabled node for PCIe endpoint mode
> >   ARM: dts: artpec: add node for hardware crypto accelerator
> 
> For a series eight patches, a pull request would save me some work, but
> I applied it anyway.

Thank you Arnd.
You will receive pull requests in the future.

> 
> Are you sure that the first three patches shouldn't be applied to stable
> backports?

The only DTS available upstream is for the ARTPEC-6 devboard.
Considering that ARTPEC-6 devboards are only used in-house,
I don't see a reason to backport anything from this series.


Best regards,
Niklas

Re: [PATCH v2 0/8] ARTPEC-6 ARM SoC device tree updates

[Niklas Cassel]

On Tue, Mar 06, 2018 at 05:45:30PM +0100, Arnd Bergmann wrote:
> On Wed, Feb 21, 2018 at 9:59 AM, Niklas Cassel <niklas.cassel@axis.com> wrote:
> > Hello,
> >
> > Here comes some ARTPEC-6 ARM SoC device tree updates.
> >
> > Niklas Cassel (8):
> >   ARM: dts: artpec: disable Accelerator Coherency Port
> >   ARM: dts: artpec: use 1 GiB RAM
> >   ARM: dts: artpec: remove 0x prefix from clkctrl unit address
> >   ARM: dts: artpec: migrate ethernet to stmmac binding
> >   ARM: dts: artpec: add and utilize artpec6 pin controller
> >   ARM: dts: artpec: add and utilize nbpfaxi DMA controllers
> >   ARM: dts: artpec: add disabled node for PCIe endpoint mode
> >   ARM: dts: artpec: add node for hardware crypto accelerator
> 
> For a series eight patches, a pull request would save me some work, but
> I applied it anyway.

Thank you Arnd.
You will receive pull requests in the future.

> 
> Are you sure that the first three patches shouldn't be applied to stable
> backports?

The only DTS available upstream is for the ARTPEC-6 devboard.
Considering that ARTPEC-6 devboards are only used in-house,
I don't see a reason to backport anything from this series.


Best regards,
Niklas

[PATCH v2 0/8] ARTPEC-6 ARM SoC device tree updates

[Arnd Bergmann]

On Wed, Mar 7, 2018 at 3:40 PM, Niklas Cassel <niklas.cassel@axis.com> wrote:
> On Tue, Mar 06, 2018 at 05:45:30PM +0100, Arnd Bergmann wrote:
>> On Wed, Feb 21, 2018 at 9:59 AM, Niklas Cassel <niklas.cassel@axis.com> wrote:
>> > Hello,
>> >
>> > Here comes some ARTPEC-6 ARM SoC device tree updates.
>> >
>> > Niklas Cassel (8):
>> >   ARM: dts: artpec: disable Accelerator Coherency Port
>> >   ARM: dts: artpec: use 1 GiB RAM
>> >   ARM: dts: artpec: remove 0x prefix from clkctrl unit address
>> >   ARM: dts: artpec: migrate ethernet to stmmac binding
>> >   ARM: dts: artpec: add and utilize artpec6 pin controller
>> >   ARM: dts: artpec: add and utilize nbpfaxi DMA controllers
>> >   ARM: dts: artpec: add disabled node for PCIe endpoint mode
>> >   ARM: dts: artpec: add node for hardware crypto accelerator
>>
>> For a series eight patches, a pull request would save me some work, but
>> I applied it anyway.
>
> Thank you Arnd.
> You will receive pull requests in the future.
>
>>
>> Are you sure that the first three patches shouldn't be applied to stable
>> backports?
>
> The only DTS available upstream is for the ARTPEC-6 devboard.
> Considering that ARTPEC-6 devboards are only used in-house,
> I don't see a reason to backport anything from this series.

Ok, makes sense. Thanks for checking!

      Arnd

Re: [PATCH v2 0/8] ARTPEC-6 ARM SoC device tree updates

[Arnd Bergmann]

On Wed, Mar 7, 2018 at 3:40 PM, Niklas Cassel <niklas.cassel@axis.com> wrote:
> On Tue, Mar 06, 2018 at 05:45:30PM +0100, Arnd Bergmann wrote:
>> On Wed, Feb 21, 2018 at 9:59 AM, Niklas Cassel <niklas.cassel@axis.com> wrote:
>> > Hello,
>> >
>> > Here comes some ARTPEC-6 ARM SoC device tree updates.
>> >
>> > Niklas Cassel (8):
>> >   ARM: dts: artpec: disable Accelerator Coherency Port
>> >   ARM: dts: artpec: use 1 GiB RAM
>> >   ARM: dts: artpec: remove 0x prefix from clkctrl unit address
>> >   ARM: dts: artpec: migrate ethernet to stmmac binding
>> >   ARM: dts: artpec: add and utilize artpec6 pin controller
>> >   ARM: dts: artpec: add and utilize nbpfaxi DMA controllers
>> >   ARM: dts: artpec: add disabled node for PCIe endpoint mode
>> >   ARM: dts: artpec: add node for hardware crypto accelerator
>>
>> For a series eight patches, a pull request would save me some work, but
>> I applied it anyway.
>
> Thank you Arnd.
> You will receive pull requests in the future.
>
>>
>> Are you sure that the first three patches shouldn't be applied to stable
>> backports?
>
> The only DTS available upstream is for the ARTPEC-6 devboard.
> Considering that ARTPEC-6 devboards are only used in-house,
> I don't see a reason to backport anything from this series.

Ok, makes sense. Thanks for checking!

      Arnd