Re: [PATCH net-next] lan78xx: Lan7801 Support for Fixed PHY

[Andrew Lunn <andrew@lunn.ch>]

>  #define DRIVER_AUTHOR	"WOOJUNG HUH <woojung.huh@microchip.com>"
>  #define DRIVER_DESC	"LAN78XX USB 3.0 Gigabit Ethernet Devices"
>  #define DRIVER_NAME	"lan78xx"
> -#define DRIVER_VERSION	"1.0.6"
> +#define DRIVER_VERSION	"1.0.7"

Hi Raghuram

Driver version strings a pretty pointless. You might want to remove
it.

>  
>  #define TX_TIMEOUT_JIFFIES		(5 * HZ)
>  #define THROTTLE_JIFFIES		(HZ / 8)
> @@ -426,6 +426,7 @@ struct lan78xx_net {
>  	struct statstage	stats;
>  
>  	struct irq_domain_data	domain_data;
> +	struct phy_device	*fixedphy;
>  };
>  
>  /* define external phy id */
> @@ -2062,11 +2063,39 @@ static int lan78xx_phy_init(struct lan78xx_net *dev)
>  	int ret;
>  	u32 mii_adv;
>  	struct phy_device *phydev;
> +	struct fixed_phy_status fphy_status = {
> +		.link = 1,
> +		.speed = SPEED_1000,
> +		.duplex = DUPLEX_FULL,
> +	};
>  
>  	phydev = phy_find_first(dev->mdiobus);
>  	if (!phydev) {
> -		netdev_err(dev->net, "no PHY found\n");
> -		return -EIO;
> +		if (dev->chipid == ID_REV_CHIP_ID_7801_) {
> +			u32 buf;
> +
> +			netdev_info(dev->net, "PHY Not Found!! Registering Fixed PHY\n");
> +			phydev = fixed_phy_register(PHY_POLL, &fphy_status, -1,
> +						    NULL);
> +			if (IS_ERR(phydev)) {
> +				netdev_err(dev->net, "No PHY/fixed_PHY found\n");
> +				return -ENODEV;
> +			}
> +			netdev_info(dev->net, "Registered FIXED PHY\n");

There are too many detdev_info() messages here. Maybe make them both
netdev_dbg().

> +			dev->interface = PHY_INTERFACE_MODE_RGMII;
> +			dev->fixedphy = phydev;

You can use 

if (!phy_is_pseudo_fixed_link(phydev))

to determine is a PHY is a fixed phy. I think you can then do without
dev->fixedphy.

> +			ret = lan78xx_write_reg(dev, MAC_RGMII_ID,
> +						MAC_RGMII_ID_TXC_DELAY_EN_);
> +			ret = lan78xx_write_reg(dev, RGMII_TX_BYP_DLL, 0x3D00);
> +			ret = lan78xx_read_reg(dev, HW_CFG, &buf);
> +			buf |= HW_CFG_CLK125_EN_;
> +			buf |= HW_CFG_REFCLK25_EN_;
> +			ret = lan78xx_write_reg(dev, HW_CFG, buf);
> +			goto phyinit;

Please don't use a goto like this. Maybe turn this into a switch statement?

> +		} else {
> +			netdev_err(dev->net, "no PHY found\n");
> +			return -EIO;
> +		}
>  	}
>  
>  	if ((dev->chipid == ID_REV_CHIP_ID_7800_) ||
> @@ -2105,6 +2134,7 @@ static int lan78xx_phy_init(struct lan78xx_net *dev)
>  		goto error;

Please take a look at what happens at error: It does not look
correct. Probably now is a good time to refactor the whole of lan78xx_phy_init()

	 Andrew