From: shawnguo@kernel.org (Shawn Guo)
To: linux-arm-kernel@lists.infradead.org
Subject: [PACTCH v5 2/2] ARM: dts: imx: Add basic dts support for imx6sll EVK board
Date: Wed, 2 May 2018 14:58:59 +0800 [thread overview]
Message-ID: <20180502065858.GB3443@dragon> (raw)
In-Reply-To: <1523606464-21561-2-git-send-email-ping.bai@nxp.com>
On Fri, Apr 13, 2018 at 04:01:04PM +0800, Bai Ping wrote:
> Add dts file support for imx6sll EVK board.
>
> Signed-off-by: Bai Ping <ping.bai@nxp.com>
> Reviewed-by: Rob Herring <robh@kernel.org>
> ---
> change v3->v4
> - update the license indentifier
> - remove leading zero of node
> - remove unused pin from hog group
> change v4->v5
> - use generic name for device node
> - remove unnecessary hog pin group
> ---
> Documentation/devicetree/bindings/arm/fsl.txt | 4 +
> arch/arm/boot/dts/Makefile | 2 +
> arch/arm/boot/dts/imx6sll-evk.dts | 315 ++++++++++++++++++++++++++
> 3 files changed, 321 insertions(+)
> create mode 100644 arch/arm/boot/dts/imx6sll-evk.dts
<snip>
> +/ {
> + model = "Freescale i.MX6SLL EVK Board";
> + compatible = "fsl,imx6sll-evk", "fsl,imx6sll";
> +
> + memory at 80000000 {
> + reg = <0x80000000 0x80000000>;
> + };
> +
> + backlight {
> + compatible = "pwm-backlight";
> + pwms = <&pwm1 0 5000000>;
> + brightness-levels = <0 4 8 16 32 64 128 255>;
> + default-brightness-level = <6>;
> + status = "okay";
The "okay" status is used to flip the default disabled device. It's not
really needed here.
> + };
> +
> + reg_usb_otg1_vbus: regulator-otg1-vbus {
> + compatible = "regulator-fixed";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usb_otg1_vbus>;
> + regulator-name = "usb_otg1_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + gpio = <&gpio4 0 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> + reg_usb_otg2_vbus: regulator-otg2-vbus {
> + compatible = "regulator-fixed";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usb_otg2_vbus>;
> + regulator-name = "usb_otg2_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + gpio = <&gpio4 2 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> + reg_aud3v: regulator-aud3v {
> + compatible = "regulator-fixed";
> + regulator-name = "wm8962-supply-3v15";
> + regulator-min-microvolt = <3150000>;
> + regulator-max-microvolt = <3150000>;
> + regulator-boot-on;
> + };
> +
> + reg_aud4v: regulator-aud4v {
> + compatible = "regulator-fixed";
> + regulator-name = "wm8962-supply-4v2";
> + regulator-min-microvolt = <4325000>;
> + regulator-max-microvolt = <4325000>;
> + regulator-boot-on;
> + };
> +
> + reg_lcd: regulator-lcd {
> + compatible = "regulator-fixed";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_reg_lcd>;
> + regulator-name = "lcd-pwr";
> + gpio = <&gpio4 8 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> + reg_sd1_vmmc: regulator-sd1-vmmc {
> + compatible = "regulator-fixed";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_reg_sd1_vmmc>;
> + regulator-name = "SD1_SPWR";
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3000000>;
> + gpio = <&gpio3 30 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +};
> +
> +&cpu0 {
> + arm-supply = <&sw1a_reg>;
> + soc-supply = <&sw1c_reg>;
> +};
> +
> +&i2c1 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c1>;
> + status = "okay";
> +
> + pfuze100: pmic at 8 {
> + compatible = "fsl,pfuze100";
> + reg = <0x08>;
> +
> + regulators {
> + sw1a_reg: sw1ab {
> + regulator-min-microvolt = <300000>;
> + regulator-max-microvolt = <1875000>;
> + regulator-boot-on;
> + regulator-always-on;
> + regulator-ramp-delay = <6250>;
> + };
> +
> + sw1c_reg: sw1c {
> + regulator-min-microvolt = <300000>;
> + regulator-max-microvolt = <1875000>;
> + regulator-boot-on;
> + regulator-always-on;
> + regulator-ramp-delay = <6250>;
> + };
> +
> + sw2_reg: sw2 {
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + sw3a_reg: sw3a {
> + regulator-min-microvolt = <400000>;
> + regulator-max-microvolt = <1975000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + sw3b_reg: sw3b {
> + regulator-min-microvolt = <400000>;
> + regulator-max-microvolt = <1975000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + sw4_reg: sw4 {
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + swbst_reg: swbst {
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5150000>;
> + };
> +
> + snvs_reg: vsnvs {
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <3000000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vref_reg: vrefddr {
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vgen1_reg: vgen1 {
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <1550000>;
> + regulator-always-on;
> + };
> +
> + vgen2_reg: vgen2 {
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <1550000>;
> + };
> +
> + vgen3_reg: vgen3 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + vgen4_reg: vgen4 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + vgen5_reg: vgen5 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + vgen6_reg: vgen6 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> + };
> + };
> +};
> +
> +&iomuxc {
> + pinctrl_usb_otg1_vbus: vbus1grp {
> + fsl,pins = <
> + MX6SLL_PAD_KEY_COL4__GPIO4_IO00 0x17059
> + >;
> + };
> +
> + pinctrl_usb_otg2_vbus: vbus2grp {
> + fsl,pins = <
> + MX6SLL_PAD_KEY_COL5__GPIO4_IO02 0x17059
> + >;
> + };
> +
> + pinctrl_reg_lcd: reglcdgrp {
> + fsl,pins = <
> + MX6SLL_PAD_ECSPI1_SCLK__GPIO4_IO08 0x17059
> + >;
> + };
> +
> + pinctrl_reg_sd1_vmmc: sd1vmmcgrp {
> + fsl,pins = <
> + MX6SLL_PAD_KEY_COL3__GPIO3_IO30 0x17059
> + >;
> + };
> +
> + pinctrl_uart1: uart1grp {
> + fsl,pins = <
> + MX6SLL_PAD_UART1_TXD__UART1_DCE_TX 0x1b0b1
> + MX6SLL_PAD_UART1_RXD__UART1_DCE_RX 0x1b0b1
> + >;
> + };
> +
> + pinctrl_usdhc1: usdhc1grp {
> + fsl,pins = <
> + MX6SLL_PAD_SD1_CMD__SD1_CMD 0x17059
> + MX6SLL_PAD_SD1_CLK__SD1_CLK 0x13059
> + MX6SLL_PAD_SD1_DATA0__SD1_DATA0 0x17059
> + MX6SLL_PAD_SD1_DATA1__SD1_DATA1 0x17059
> + MX6SLL_PAD_SD1_DATA2__SD1_DATA2 0x17059
> + MX6SLL_PAD_SD1_DATA3__SD1_DATA3 0x17059
> + >;
> + };
> +
> + pinctrl_usdhc1_100mhz: usdhc1grp_100mhz {
> + fsl,pins = <
> + MX6SLL_PAD_SD1_CMD__SD1_CMD 0x170b9
> + MX6SLL_PAD_SD1_CLK__SD1_CLK 0x130b9
> + MX6SLL_PAD_SD1_DATA0__SD1_DATA0 0x170b9
> + MX6SLL_PAD_SD1_DATA1__SD1_DATA1 0x170b9
> + MX6SLL_PAD_SD1_DATA2__SD1_DATA2 0x170b9
> + MX6SLL_PAD_SD1_DATA3__SD1_DATA3 0x170b9
> + >;
> + };
> +
> + pinctrl_usdhc1_200mhz: usdhc1grp_200mhz {
> + fsl,pins = <
> + MX6SLL_PAD_SD1_CMD__SD1_CMD 0x170f9
> + MX6SLL_PAD_SD1_CLK__SD1_CLK 0x130f9
> + MX6SLL_PAD_SD1_DATA0__SD1_DATA0 0x170f9
> + MX6SLL_PAD_SD1_DATA1__SD1_DATA1 0x170f9
> + MX6SLL_PAD_SD1_DATA2__SD1_DATA2 0x170f9
> + MX6SLL_PAD_SD1_DATA3__SD1_DATA3 0x170f9
> + >;
> + };
> +
> + pinctrl_usbotg1: usbotg1grp {
> + fsl,pins = <
> + MX6SLL_PAD_EPDC_PWR_COM__USB_OTG1_ID 0x17059
> + >;
> + };
> +
> + pinctrl_i2c1: i2c1grp {
> + fsl,pins = <
> + MX6SLL_PAD_I2C1_SCL__I2C1_SCL 0x4001b8b1
> + MX6SLL_PAD_I2C1_SDA__I2C1_SDA 0x4001b8b1
> + >;
> + };
Please try to sort these pinctrl nodes alphabetically.
Shawn
> +};
> +
> +&uart1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart1>;
> + status = "okay";
> +};
> +
> +&usdhc1 {
> + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> + pinctrl-0 = <&pinctrl_usdhc1>;
> + pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
> + pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
> + cd-gpios = <&gpio4 7 GPIO_ACTIVE_LOW>;
> + wp-gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>;
> + keep-power-in-suspend;
> + wakeup-source;
> + vmmc-supply = <®_sd1_vmmc>;
> + status = "okay";
> +};
> +
> +&usbotg1 {
> + vbus-supply = <®_usb_otg1_vbus>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usbotg1>;
> + disable-over-current;
> + srp-disable;
> + hnp-disable;
> + adp-disable;
> + status = "okay";
> +};
> +
> +&usbotg2 {
> + vbus-supply = <®_usb_otg2_vbus>;
> + dr_mode = "host";
> + disable-over-current;
> + status = "okay";
> +};
> --
> 1.9.1
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
WARNING: multiple messages have this Message-ID (diff)
From: Shawn Guo <shawnguo@kernel.org>
To: Bai Ping <ping.bai@nxp.com>
Cc: aisheng.dong@nxp.com, devicetree@vger.kernel.org,
robh+dt@kernel.org, linux-imx@nxp.com, kernel@pengutronix.de,
jacky.baip@gmail.com, fabio.estevam@nxp.com,
linux-arm-kernel@lists.infradead.org
Subject: Re: [PACTCH v5 2/2] ARM: dts: imx: Add basic dts support for imx6sll EVK board
Date: Wed, 2 May 2018 14:58:59 +0800 [thread overview]
Message-ID: <20180502065858.GB3443@dragon> (raw)
In-Reply-To: <1523606464-21561-2-git-send-email-ping.bai@nxp.com>
On Fri, Apr 13, 2018 at 04:01:04PM +0800, Bai Ping wrote:
> Add dts file support for imx6sll EVK board.
>
> Signed-off-by: Bai Ping <ping.bai@nxp.com>
> Reviewed-by: Rob Herring <robh@kernel.org>
> ---
> change v3->v4
> - update the license indentifier
> - remove leading zero of node
> - remove unused pin from hog group
> change v4->v5
> - use generic name for device node
> - remove unnecessary hog pin group
> ---
> Documentation/devicetree/bindings/arm/fsl.txt | 4 +
> arch/arm/boot/dts/Makefile | 2 +
> arch/arm/boot/dts/imx6sll-evk.dts | 315 ++++++++++++++++++++++++++
> 3 files changed, 321 insertions(+)
> create mode 100644 arch/arm/boot/dts/imx6sll-evk.dts
<snip>
> +/ {
> + model = "Freescale i.MX6SLL EVK Board";
> + compatible = "fsl,imx6sll-evk", "fsl,imx6sll";
> +
> + memory@80000000 {
> + reg = <0x80000000 0x80000000>;
> + };
> +
> + backlight {
> + compatible = "pwm-backlight";
> + pwms = <&pwm1 0 5000000>;
> + brightness-levels = <0 4 8 16 32 64 128 255>;
> + default-brightness-level = <6>;
> + status = "okay";
The "okay" status is used to flip the default disabled device. It's not
really needed here.
> + };
> +
> + reg_usb_otg1_vbus: regulator-otg1-vbus {
> + compatible = "regulator-fixed";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usb_otg1_vbus>;
> + regulator-name = "usb_otg1_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + gpio = <&gpio4 0 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> + reg_usb_otg2_vbus: regulator-otg2-vbus {
> + compatible = "regulator-fixed";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usb_otg2_vbus>;
> + regulator-name = "usb_otg2_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + gpio = <&gpio4 2 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> + reg_aud3v: regulator-aud3v {
> + compatible = "regulator-fixed";
> + regulator-name = "wm8962-supply-3v15";
> + regulator-min-microvolt = <3150000>;
> + regulator-max-microvolt = <3150000>;
> + regulator-boot-on;
> + };
> +
> + reg_aud4v: regulator-aud4v {
> + compatible = "regulator-fixed";
> + regulator-name = "wm8962-supply-4v2";
> + regulator-min-microvolt = <4325000>;
> + regulator-max-microvolt = <4325000>;
> + regulator-boot-on;
> + };
> +
> + reg_lcd: regulator-lcd {
> + compatible = "regulator-fixed";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_reg_lcd>;
> + regulator-name = "lcd-pwr";
> + gpio = <&gpio4 8 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> + reg_sd1_vmmc: regulator-sd1-vmmc {
> + compatible = "regulator-fixed";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_reg_sd1_vmmc>;
> + regulator-name = "SD1_SPWR";
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3000000>;
> + gpio = <&gpio3 30 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +};
> +
> +&cpu0 {
> + arm-supply = <&sw1a_reg>;
> + soc-supply = <&sw1c_reg>;
> +};
> +
> +&i2c1 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c1>;
> + status = "okay";
> +
> + pfuze100: pmic@8 {
> + compatible = "fsl,pfuze100";
> + reg = <0x08>;
> +
> + regulators {
> + sw1a_reg: sw1ab {
> + regulator-min-microvolt = <300000>;
> + regulator-max-microvolt = <1875000>;
> + regulator-boot-on;
> + regulator-always-on;
> + regulator-ramp-delay = <6250>;
> + };
> +
> + sw1c_reg: sw1c {
> + regulator-min-microvolt = <300000>;
> + regulator-max-microvolt = <1875000>;
> + regulator-boot-on;
> + regulator-always-on;
> + regulator-ramp-delay = <6250>;
> + };
> +
> + sw2_reg: sw2 {
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + sw3a_reg: sw3a {
> + regulator-min-microvolt = <400000>;
> + regulator-max-microvolt = <1975000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + sw3b_reg: sw3b {
> + regulator-min-microvolt = <400000>;
> + regulator-max-microvolt = <1975000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + sw4_reg: sw4 {
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + swbst_reg: swbst {
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5150000>;
> + };
> +
> + snvs_reg: vsnvs {
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <3000000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vref_reg: vrefddr {
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vgen1_reg: vgen1 {
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <1550000>;
> + regulator-always-on;
> + };
> +
> + vgen2_reg: vgen2 {
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <1550000>;
> + };
> +
> + vgen3_reg: vgen3 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + vgen4_reg: vgen4 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + vgen5_reg: vgen5 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + vgen6_reg: vgen6 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> + };
> + };
> +};
> +
> +&iomuxc {
> + pinctrl_usb_otg1_vbus: vbus1grp {
> + fsl,pins = <
> + MX6SLL_PAD_KEY_COL4__GPIO4_IO00 0x17059
> + >;
> + };
> +
> + pinctrl_usb_otg2_vbus: vbus2grp {
> + fsl,pins = <
> + MX6SLL_PAD_KEY_COL5__GPIO4_IO02 0x17059
> + >;
> + };
> +
> + pinctrl_reg_lcd: reglcdgrp {
> + fsl,pins = <
> + MX6SLL_PAD_ECSPI1_SCLK__GPIO4_IO08 0x17059
> + >;
> + };
> +
> + pinctrl_reg_sd1_vmmc: sd1vmmcgrp {
> + fsl,pins = <
> + MX6SLL_PAD_KEY_COL3__GPIO3_IO30 0x17059
> + >;
> + };
> +
> + pinctrl_uart1: uart1grp {
> + fsl,pins = <
> + MX6SLL_PAD_UART1_TXD__UART1_DCE_TX 0x1b0b1
> + MX6SLL_PAD_UART1_RXD__UART1_DCE_RX 0x1b0b1
> + >;
> + };
> +
> + pinctrl_usdhc1: usdhc1grp {
> + fsl,pins = <
> + MX6SLL_PAD_SD1_CMD__SD1_CMD 0x17059
> + MX6SLL_PAD_SD1_CLK__SD1_CLK 0x13059
> + MX6SLL_PAD_SD1_DATA0__SD1_DATA0 0x17059
> + MX6SLL_PAD_SD1_DATA1__SD1_DATA1 0x17059
> + MX6SLL_PAD_SD1_DATA2__SD1_DATA2 0x17059
> + MX6SLL_PAD_SD1_DATA3__SD1_DATA3 0x17059
> + >;
> + };
> +
> + pinctrl_usdhc1_100mhz: usdhc1grp_100mhz {
> + fsl,pins = <
> + MX6SLL_PAD_SD1_CMD__SD1_CMD 0x170b9
> + MX6SLL_PAD_SD1_CLK__SD1_CLK 0x130b9
> + MX6SLL_PAD_SD1_DATA0__SD1_DATA0 0x170b9
> + MX6SLL_PAD_SD1_DATA1__SD1_DATA1 0x170b9
> + MX6SLL_PAD_SD1_DATA2__SD1_DATA2 0x170b9
> + MX6SLL_PAD_SD1_DATA3__SD1_DATA3 0x170b9
> + >;
> + };
> +
> + pinctrl_usdhc1_200mhz: usdhc1grp_200mhz {
> + fsl,pins = <
> + MX6SLL_PAD_SD1_CMD__SD1_CMD 0x170f9
> + MX6SLL_PAD_SD1_CLK__SD1_CLK 0x130f9
> + MX6SLL_PAD_SD1_DATA0__SD1_DATA0 0x170f9
> + MX6SLL_PAD_SD1_DATA1__SD1_DATA1 0x170f9
> + MX6SLL_PAD_SD1_DATA2__SD1_DATA2 0x170f9
> + MX6SLL_PAD_SD1_DATA3__SD1_DATA3 0x170f9
> + >;
> + };
> +
> + pinctrl_usbotg1: usbotg1grp {
> + fsl,pins = <
> + MX6SLL_PAD_EPDC_PWR_COM__USB_OTG1_ID 0x17059
> + >;
> + };
> +
> + pinctrl_i2c1: i2c1grp {
> + fsl,pins = <
> + MX6SLL_PAD_I2C1_SCL__I2C1_SCL 0x4001b8b1
> + MX6SLL_PAD_I2C1_SDA__I2C1_SDA 0x4001b8b1
> + >;
> + };
Please try to sort these pinctrl nodes alphabetically.
Shawn
> +};
> +
> +&uart1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart1>;
> + status = "okay";
> +};
> +
> +&usdhc1 {
> + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> + pinctrl-0 = <&pinctrl_usdhc1>;
> + pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
> + pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
> + cd-gpios = <&gpio4 7 GPIO_ACTIVE_LOW>;
> + wp-gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>;
> + keep-power-in-suspend;
> + wakeup-source;
> + vmmc-supply = <®_sd1_vmmc>;
> + status = "okay";
> +};
> +
> +&usbotg1 {
> + vbus-supply = <®_usb_otg1_vbus>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usbotg1>;
> + disable-over-current;
> + srp-disable;
> + hnp-disable;
> + adp-disable;
> + status = "okay";
> +};
> +
> +&usbotg2 {
> + vbus-supply = <®_usb_otg2_vbus>;
> + dr_mode = "host";
> + disable-over-current;
> + status = "okay";
> +};
> --
> 1.9.1
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2018-05-02 6:58 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-04-13 8:01 [PACTCH v5 1/2] ARM: dts: imx: Add basic dtsi file for imx6sll Bai Ping
2018-04-13 8:01 ` [PACTCH v5 2/2] ARM: dts: imx: Add basic dts support for imx6sll EVK board Bai Ping
2018-04-13 8:01 ` Bai Ping
2018-05-02 6:58 ` Shawn Guo [this message]
2018-05-02 6:58 ` Shawn Guo
2018-05-02 6:55 ` [PACTCH v5 1/2] ARM: dts: imx: Add basic dtsi file for imx6sll Shawn Guo
2018-05-02 6:55 ` Shawn Guo
2018-05-08 7:52 ` Jacky Bai
2018-05-08 7:52 ` Jacky Bai
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20180502065858.GB3443@dragon \
--to=shawnguo@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.