[PATCH 3/3] ARM: dts: imx: add ZII SCU2 Mezz board

[shawnguo@kernel.org (Shawn Guo)]

On Thu, Jun 21, 2018 at 08:45:00PM +0300, Andrey Gusakov wrote:
> This adds support for the Zodiac Inflight Innovations SCU2 Mezz
> board, which is based on the i.MX51.
> 
> Signed-off-by: Andrey Gusakov <andrey.gusakov@cogentembedded.com>
> ---
>  arch/arm/boot/dts/Makefile                |   3 +-
>  arch/arm/boot/dts/imx51-zii-scu2-mezz.dts | 190 ++++++++++++++++++++++++++++++
>  2 files changed, 192 insertions(+), 1 deletion(-)
>  create mode 100644 arch/arm/boot/dts/imx51-zii-scu2-mezz.dts
> 
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index d8900f4..e0dc187 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -359,7 +359,8 @@ dtb-$(CONFIG_SOC_IMX51) += \
>  	imx51-eukrea-mbimxsd51-baseboard.dtb \
>  	imx51-ts4800.dtb \
>  	imx51-zii-rdu1.dtb \
> -	imx51-zii-scu2-esb.dtb
> +	imx51-zii-scu2-esb.dtb \
> +	imx51-zii-scu2-mezz.dtb
>  dtb-$(CONFIG_SOC_IMX53) += \
>  	imx53-ard.dtb \
>  	imx53-cx9020.dtb \
> diff --git a/arch/arm/boot/dts/imx51-zii-scu2-mezz.dts b/arch/arm/boot/dts/imx51-zii-scu2-mezz.dts
> new file mode 100644
> index 0000000..f58572a
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx51-zii-scu2-mezz.dts
> @@ -0,0 +1,190 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +// Copyright (C) 2018 Zodiac Inflight Innovations
> +
> +/dts-v1/;
> +#include "imx51-zii-common.dtsi"
> +
> +/ {
> +	model = "ZII SCU2 Mezz Board";
> +	compatible = "zii,imx51-scu2-mezz", "fsl,imx51";
> +
> +	aliases {
> +		mdio-gpio0 = &mdio_gpio;
> +	};
> +
> +	mdio_gpio: mdio-gpio {
> +		compatible = "virtual,mdio-gpio";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_swmdio>;
> +		gpios = <&gpio2 7 GPIO_ACTIVE_HIGH>, /* mdc */
> +			<&gpio2 6 GPIO_ACTIVE_HIGH>; /* mdio */
> +

The newline in middle of property list is not really necessary.

> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		switch at 0 {
> +			compatible = "marvell,mv88e6085";
> +			reg = <0>;
> +			dsa,member = <0 0>;
> +			eeprom-length = <512>;
> +			interrupt-parent = <&gpio1>;
> +			interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +
> +			ports {
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				port at 0 {
> +					reg = <0>;
> +					label = "port4";
> +				};
> +
> +				port at 1 {
> +					reg = <1>;
> +					label = "port5";
> +				};
> +
> +				port at 2 {
> +					reg = <2>;
> +					label = "port6";
> +				};
> +
> +				port at 3 {
> +					reg = <3>;
> +					label = "port7";
> +				};
> +
> +				port at 4 {
> +					reg = <4>;
> +					label = "cpu";
> +					ethernet = <&fec>;
> +
> +					fixed-link {
> +						speed = <100>;
> +						full-duplex;
> +					};
> +				};
> +
> +				port at 5 {
> +					reg = <5>;
> +					label = "mezz2esb";
> +					phy-mode = "sgmii";

Please have a newline between property list and child node.

> +					fixed-link {
> +						speed = <1000>;
> +						full-duplex;
> +					};
> +				};
> +			};
> +		};
> +	};
> +};
> +
> +&usb_vbus {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_usb_mmc_reset>;
> +	gpio = <&gpio3 13 GPIO_ACTIVE_LOW>;
> +	startup-delay-us = <150000>;
> +};

Please sort these labelled nodes alphabetically in label name.  &iomuxc
can be an exception though.

> +
> +&esdhc1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_esdhc1_4bit &pinctrl_esdhc1_8bit>;
> +	bus-width = <8>;
> +};
> +
> +&fec {
> +	phy-reset-gpios = <&gpio2 14 GPIO_ACTIVE_LOW>;
> +	phy-reset-duration = <1>;
> +	phy-supply = <&vgen3_reg>;
> +	phy-handle = <&ethphy>;
> +
> +	mdio {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		ethphy: ethernet-phy at 0 {
> +			reg = <0>;
> +			max-speed = <100>;
> +		};
> +	};
> +};
> +
> +
> +&i2c_gpio {
> +	gpios = <&gpio3 2 GPIO_ACTIVE_HIGH>, /* sda */
> +		<&gpio3 1 GPIO_ACTIVE_HIGH>; /* scl */
> +};
> +
> +&uart2 {
> +	status = "disabled";
> +};
> +
> +&vsd_reg {
> +	regulator-always-on;
> +};
> +
> +&iomuxc {
> +	pinctrl_fec: fecgrp {
> +		fsl,pins = <
> +			MX51_PAD_DISP2_DAT15__FEC_TDATA0	0x2004
> +			MX51_PAD_DISP2_DAT6__FEC_TDATA1		0x2004
> +			MX51_PAD_DISP2_DAT7__FEC_TDATA2		0x2004
> +			MX51_PAD_DISP2_DAT8__FEC_TDATA3		0x2004
> +			MX51_PAD_DISP2_DAT9__FEC_TX_EN		0x2004
> +			MX51_PAD_DISP2_DAT10__FEC_COL		0x0180
> +			MX51_PAD_DISP2_DAT11__FEC_RX_CLK	0x0180
> +			MX51_PAD_DISP2_DAT12__FEC_RX_DV		0x20a4
> +			MX51_PAD_DISP2_DAT1__FEC_RX_ER		0x20a4
> +			MX51_PAD_DISP2_DAT13__FEC_TX_CLK	0x2180
> +			MX51_PAD_DI_GP3__FEC_TX_ER		0x2004
> +			MX51_PAD_DISP2_DAT14__FEC_RDATA0	0x2180
> +			MX51_PAD_DI2_DISP_CLK__FEC_RDATA1	0x0085
> +			MX51_PAD_DI_GP4__FEC_RDATA2		0x0085
> +			MX51_PAD_DISP2_DAT0__FEC_RDATA3		0x0085
> +			MX51_PAD_DI2_PIN2__FEC_MDC		0x2004
> +			MX51_PAD_DI2_PIN3__FEC_MDIO		0x01f5
> +			MX51_PAD_DI2_PIN4__FEC_CRS		0x0180
> +			MX51_PAD_EIM_A20__GPIO2_14		0x0085
> +			MX51_PAD_EIM_A21__GPIO2_15		0x00e5
> +		>;
> +	};
> +
> +	pinctrl_uart1: uart1grp {
> +		fsl,pins = <
> +			MX51_PAD_UART1_RXD__UART1_RXD		0x1c5
> +			MX51_PAD_UART1_TXD__UART1_TXD		0x1c5
> +		>;
> +	};
> +
> +	pinctrl_uart2: uart2grp {
> +	};

Why this empty pinctrl?

> +
> +	pinctrl_uart3: uart3grp {
> +		fsl,pins = <
> +			MX51_PAD_UART3_RXD__UART3_RXD		0x1c5
> +			MX51_PAD_UART3_TXD__UART3_TXD		0x1c5
> +		>;
> +	};
> +
> +	pinctrl_usb_mmc_reset: usbmmcgrp {
> +		fsl,pins = <
> +			MX51_PAD_CSI1_D9__GPIO3_13		0x85
> +		>;
> +	};
> +
> +	pinctrl_swmdio: swmdiogrp {
> +		fsl,pins = <
> +			MX51_PAD_EIM_D22__GPIO2_6		0x100
> +			MX51_PAD_EIM_D23__GPIO2_7		0x100
> +		>;
> +	};
> +
> +	pinctrl_swi2c: swi2cgrp {
> +		fsl,pins = <
> +			MX51_PAD_DI1_PIN12__GPIO3_1		0x100
> +			MX51_PAD_DI1_PIN13__GPIO3_2		0x100
> +		>;
> +	};

Please sort these pinctrl nodes alphabetically as well.

Shawn

> +};
> -- 
> 1.9.1
>