All of lore.kernel.org
 help / color / mirror / Atom feed
From: mathieu.poirier@linaro.org (Mathieu Poirier)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v2 10/10] coresight: etm-perf: Add support for ETR backend
Date: Thu, 19 Jul 2018 13:59:49 -0600	[thread overview]
Message-ID: <20180719195949.GA9421@xps15> (raw)
In-Reply-To: <1531847501-22226-11-git-send-email-suzuki.poulose@arm.com>

On Tue, Jul 17, 2018 at 06:11:41PM +0100, Suzuki K Poulose wrote:
> Add support for using TMC-ETR as backend for ETM perf tracing.
> We use software double buffering at the moment. i.e, the TMC-ETR
> uses a separate buffer than the perf ring buffer. The data is
> copied to the perf ring buffer once a session completes.
> 
> The TMC-ETR would try to match the larger of perf ring buffer
> or the ETR buffer size configured via sysfs, scaling down to
> a minimum limit of 1MB.
> 
> Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
> Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
> ---
>  drivers/hwtracing/coresight/coresight-tmc-etr.c | 248 +++++++++++++++++++++++-
>  drivers/hwtracing/coresight/coresight-tmc.h     |   2 +
>  2 files changed, 248 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/hwtracing/coresight/coresight-tmc-etr.c b/drivers/hwtracing/coresight/coresight-tmc-etr.c
> index bc0c932..6280790 100644
> --- a/drivers/hwtracing/coresight/coresight-tmc-etr.c
> +++ b/drivers/hwtracing/coresight/coresight-tmc-etr.c
> @@ -10,6 +10,7 @@
>  #include <linux/slab.h>
>  #include <linux/vmalloc.h>
>  #include "coresight-catu.h"
> +#include "coresight-etm-perf.h"
>  #include "coresight-priv.h"
>  #include "coresight-tmc.h"
>  
> @@ -21,6 +22,28 @@ struct etr_flat_buf {
>  };
>  
>  /*
> + * etr_perf_buffer - Perf buffer used for ETR
> + * @etr_buf		- Actual buffer used by the ETR
> + * @snaphost		- Perf session mode
> + * @head		- handle->head at the beginning of the session.
> + * @nr_pages		- Number of pages in the ring buffer.
> + * @pages		- Array of Pages in the ring buffer.
> + */
> +struct etr_perf_buffer {
> +	struct etr_buf		*etr_buf;
> +	bool			snapshot;
> +	unsigned long		head;
> +	int			nr_pages;
> +	void			**pages;
> +};
> +
> +/* Convert the perf index to an offset within the ETR buffer */
> +#define PERF_IDX2OFF(idx, buf)	((idx) % ((buf)->nr_pages << PAGE_SHIFT))
> +
> +/* Lower limit for ETR hardware buffer */
> +#define TMC_ETR_PERF_MIN_BUF_SIZE	SZ_1M
> +
> +/*
>   * The TMC ETR SG has a page size of 4K. The SG table contains pointers
>   * to 4KB buffers. However, the OS may use a PAGE_SIZE different from
>   * 4K (i.e, 16KB or 64KB). This implies that a single OS page could
> @@ -1103,10 +1126,228 @@ static int tmc_enable_etr_sink_sysfs(struct coresight_device *csdev)
>  	return ret;
>  }
>  
> +/*
> + * tmc_etr_setup_perf_buf: Allocate ETR buffer for use by perf.
> + * The size of the hardware buffer is dependent on the size configured
> + * via sysfs and the perf ring buffer size. We prefer to allocate the
> + * largest possible size, scaling down the size by half until it
> + * reaches a minimum limit (1M), beyond which we give up.
> + */
> +static struct etr_perf_buffer *
> +tmc_etr_setup_perf_buf(struct tmc_drvdata *drvdata, int node, int nr_pages,
> +		       void **pages, bool snapshot)
> +{
> +	struct etr_buf *etr_buf;
> +	struct etr_perf_buffer *etr_perf;
> +	unsigned long size;
> +
> +	etr_perf = kzalloc_node(sizeof(*etr_perf), GFP_KERNEL, node);
> +	if (!etr_perf)
> +		return ERR_PTR(-ENOMEM);
> +
> +	/*
> +	 * Try to match the perf ring buffer size if it is larger
> +	 * than the size requested via sysfs.
> +	 */
> +	if ((nr_pages << PAGE_SHIFT) > drvdata->size) {
> +		etr_buf = tmc_alloc_etr_buf(drvdata, (nr_pages << PAGE_SHIFT),
> +					    0, node, NULL);
> +		if (!IS_ERR(etr_buf))
> +			goto done;
> +	}
> +
> +	/*
> +	 * Else switch to configured size for this ETR
> +	 * and scale down until we hit the minimum limit.
> +	 */
> +	size = drvdata->size;
> +	do {
> +		etr_buf = tmc_alloc_etr_buf(drvdata, size, 0, node, NULL);
> +		if (!IS_ERR(etr_buf))
> +			goto done;
> +		size /= 2;
> +	} while (size >= TMC_ETR_PERF_MIN_BUF_SIZE);
> +
> +	kfree(etr_perf);
> +	return ERR_PTR(-ENOMEM);
> +
> +done:
> +	etr_perf->etr_buf = etr_buf;
> +	return etr_perf;
> +}
> +
> +
> +static void *tmc_etr_alloc_perf_buffer(struct coresight_device *csdev,
> +				       int cpu, void **pages, int nr_pages,
> +				       bool snapshot)
> +{
> +	struct etr_perf_buffer *etr_perf;
> +	struct tmc_drvdata *drvdata = dev_get_drvdata(csdev->dev.parent);
> +
> +	if (cpu == -1)
> +		cpu = smp_processor_id();
> +
> +	etr_perf = tmc_etr_setup_perf_buf(drvdata, cpu_to_node(cpu),
> +					  nr_pages, pages, snapshot);
> +	if (IS_ERR(etr_perf)) {
> +		dev_dbg(drvdata->dev, "Unable to allocate ETR buffer\n");
> +		return NULL;
> +	}
> +
> +	etr_perf->snapshot = snapshot;
> +	etr_perf->nr_pages = nr_pages;
> +	etr_perf->pages = pages;
> +
> +	return etr_perf;
> +}
> +
> +static void tmc_etr_free_perf_buffer(void *config)
> +{
> +	struct etr_perf_buffer *etr_perf = config;
> +
> +	if (etr_perf->etr_buf)
> +		tmc_free_etr_buf(etr_perf->etr_buf);
> +	kfree(etr_perf);
> +}
> +
> +/*
> + * tmc_etr_sync_perf_buffer: Copy the actual trace data from the hardware
> + * buffer to the perf ring buffer.
> + */
> +static void tmc_etr_sync_perf_buffer(struct etr_perf_buffer *etr_perf)
> +{
> +	long bytes, to_copy;
> +	long pg_idx, pg_offset, src_offset;
> +	unsigned long head = etr_perf->head;
> +	char **dst_pages, *src_buf;
> +	struct etr_buf *etr_buf = etr_perf->etr_buf;
> +
> +	head = etr_perf->head;
> +	pg_idx = head >> PAGE_SHIFT;
> +	pg_offset = head & (PAGE_SIZE - 1);
> +	dst_pages = (char **)etr_perf->pages;
> +	src_offset = etr_buf->offset;
> +	to_copy = etr_buf->len;
> +
> +	while (to_copy > 0) {
> +		/*
> +		 * In one iteration, we can copy minimum of :
> +		 *  1) what is available in the source buffer,
> +		 *  2) what is available in the source buffer, before it
> +		 *     wraps around.
> +		 *  3) what is available in the destination page.
> +		 * in one iteration.
> +		 */
> +		bytes = tmc_etr_buf_get_data(etr_buf, src_offset, to_copy,
> +					     &src_buf);
> +		if (WARN_ON_ONCE(bytes <= 0))
> +			break;
> +		bytes = min(bytes, (long)(PAGE_SIZE - pg_offset));
> +
> +		memcpy(dst_pages[pg_idx] + pg_offset, src_buf, bytes);
> +
> +		to_copy -= bytes;
> +
> +		/* Move destination pointers */
> +		pg_offset += bytes;
> +		if (pg_offset == PAGE_SIZE) {
> +			pg_offset = 0;
> +			if (++pg_idx == etr_perf->nr_pages)
> +				pg_idx = 0;
> +		}
> +
> +		/* Move source pointers */
> +		src_offset += bytes;
> +		if (src_offset >= etr_buf->size)
> +			src_offset -= etr_buf->size;
> +	}
> +}
> +
> +/*
> + * tmc_etr_update_perf_buffer : Update the perf ring buffer with the
> + * available trace data. We use software double buffering at the moment.
> + *
> + * TODO: Add support for reusing the perf ring buffer.
> + */
> +static unsigned long
> +tmc_etr_update_perf_buffer(struct coresight_device *csdev,
> +			   struct perf_output_handle *handle,
> +			   void *config)
> +{
> +	bool lost = false;
> +	unsigned long flags, size = 0;
> +	struct tmc_drvdata *drvdata = dev_get_drvdata(csdev->dev.parent);
> +	struct etr_perf_buffer *etr_perf = config;
> +	struct etr_buf *etr_buf = etr_perf->etr_buf;
> +
> +	spin_lock_irqsave(&drvdata->spinlock, flags);
> +	if (WARN_ON(drvdata->perf_data != etr_perf)) {
> +		lost = true;
> +		spin_unlock_irqrestore(&drvdata->spinlock, flags);
> +		goto out;
> +	}
> +
> +	CS_UNLOCK(drvdata->base);
> +
> +	tmc_flush_and_stop(drvdata);
> +	tmc_sync_etr_buf(drvdata);
> +
> +	CS_UNLOCK(drvdata->base);

This is a copy/paste oversight, here you want to lock again.

> +	/* Reset perf specific data */
> +	drvdata->perf_data = NULL;
> +	spin_unlock_irqrestore(&drvdata->spinlock, flags);
> +
> +	size = etr_buf->len;
> +	tmc_etr_sync_perf_buffer(etr_perf);
> +
> +	/*
> +	 * Update handle->head in snapshot mode. Also update the size to the
> +	 * hardware buffer size if there was an overflow.
> +	 */
> +	if (etr_perf->snapshot) {
> +		handle->head += size;
> +		if (etr_buf->full)
> +			size = etr_buf->size;
> +	}
> +
> +	lost |= etr_buf->full;
> +out:
> +	if (lost)
> +		perf_aux_output_flag(handle, PERF_AUX_FLAG_TRUNCATED);
> +	return size;
> +}
> +
>  static int tmc_enable_etr_sink_perf(struct coresight_device *csdev, void *data)
>  {
> -	/* We don't support perf mode yet ! */
> -	return -EINVAL;
> +	int rc = 0;
> +	unsigned long flags;
> +	struct tmc_drvdata *drvdata = dev_get_drvdata(csdev->dev.parent);
> +	struct perf_output_handle *handle = data;
> +	struct etr_perf_buffer *etr_perf = etm_perf_sink_config(handle);
> +
> +	spin_lock_irqsave(&drvdata->spinlock, flags);
> +	/*
> +	 * There can be only one writer per sink in perf mode. If the sink
> +	 * is already open in SYSFS mode, we can't use it.
> +	 */
> +	if (drvdata->mode != CS_MODE_DISABLED || drvdata->perf_data) {
> +		rc = -EBUSY;
> +		goto unlock_out;
> +	}
> +
> +	if (WARN_ON(!etr_perf || !etr_perf->etr_buf)) {
> +		rc = -EINVAL;
> +		goto unlock_out;
> +	}
> +
> +	etr_perf->head = PERF_IDX2OFF(handle->head, etr_perf);
> +	drvdata->perf_data = etr_perf;
> +	drvdata->mode = CS_MODE_PERF;
> +	tmc_etr_enable_hw(drvdata, etr_perf->etr_buf);
> +
> +unlock_out:
> +	spin_unlock_irqrestore(&drvdata->spinlock, flags);
> +	return rc;
>  }
>  
>  static int tmc_enable_etr_sink(struct coresight_device *csdev,
> @@ -1148,6 +1389,9 @@ static void tmc_disable_etr_sink(struct coresight_device *csdev)
>  static const struct coresight_ops_sink tmc_etr_sink_ops = {
>  	.enable		= tmc_enable_etr_sink,
>  	.disable	= tmc_disable_etr_sink,
> +	.alloc_buffer	= tmc_etr_alloc_perf_buffer,
> +	.update_buffer	= tmc_etr_update_perf_buffer,
> +	.free_buffer	= tmc_etr_free_perf_buffer,


	.alloc_buffer	= tmc_alloc_etr_buffer,
	.update_buffer	= tmc_update_etr_buffer,
	.free_buffer	= tmc_free_etr_buffer,

To be consistant with .enable and .disable along with the naming convention on
the ETF side.

>  };
>  
>  const struct coresight_ops tmc_etr_cs_ops = {
> diff --git a/drivers/hwtracing/coresight/coresight-tmc.h b/drivers/hwtracing/coresight/coresight-tmc.h
> index 872f63e..487c537 100644
> --- a/drivers/hwtracing/coresight/coresight-tmc.h
> +++ b/drivers/hwtracing/coresight/coresight-tmc.h
> @@ -170,6 +170,7 @@ struct etr_buf {
>   * @trigger_cntr: amount of words to store after a trigger.
>   * @etr_caps:	Bitmask of capabilities of the TMC ETR, inferred from the
>   *		device configuration register (DEVID)
> + * @perf_data:	PERF buffer for ETR.
>   * @sysfs_data:	SYSFS buffer for ETR.
>   */
>  struct tmc_drvdata {
> @@ -191,6 +192,7 @@ struct tmc_drvdata {
>  	u32			trigger_cntr;
>  	u32			etr_caps;
>  	struct etr_buf		*sysfs_buf;
> +	void			*perf_data;
>  };
>  
>  struct etr_buf_operations {
> -- 
> 2.7.4
> 

WARNING: multiple messages have this Message-ID (diff)
From: Mathieu Poirier <mathieu.poirier@linaro.org>
To: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: linux-arm-kernel@lists.infradead.org,
	linux-kernel@vger.kernel.org, robert.walker@arm.com,
	mike.leach@linaro.org, coresight@lists.linaro.org
Subject: Re: [PATCH v2 10/10] coresight: etm-perf: Add support for ETR backend
Date: Thu, 19 Jul 2018 13:59:49 -0600	[thread overview]
Message-ID: <20180719195949.GA9421@xps15> (raw)
In-Reply-To: <1531847501-22226-11-git-send-email-suzuki.poulose@arm.com>

On Tue, Jul 17, 2018 at 06:11:41PM +0100, Suzuki K Poulose wrote:
> Add support for using TMC-ETR as backend for ETM perf tracing.
> We use software double buffering at the moment. i.e, the TMC-ETR
> uses a separate buffer than the perf ring buffer. The data is
> copied to the perf ring buffer once a session completes.
> 
> The TMC-ETR would try to match the larger of perf ring buffer
> or the ETR buffer size configured via sysfs, scaling down to
> a minimum limit of 1MB.
> 
> Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
> Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
> ---
>  drivers/hwtracing/coresight/coresight-tmc-etr.c | 248 +++++++++++++++++++++++-
>  drivers/hwtracing/coresight/coresight-tmc.h     |   2 +
>  2 files changed, 248 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/hwtracing/coresight/coresight-tmc-etr.c b/drivers/hwtracing/coresight/coresight-tmc-etr.c
> index bc0c932..6280790 100644
> --- a/drivers/hwtracing/coresight/coresight-tmc-etr.c
> +++ b/drivers/hwtracing/coresight/coresight-tmc-etr.c
> @@ -10,6 +10,7 @@
>  #include <linux/slab.h>
>  #include <linux/vmalloc.h>
>  #include "coresight-catu.h"
> +#include "coresight-etm-perf.h"
>  #include "coresight-priv.h"
>  #include "coresight-tmc.h"
>  
> @@ -21,6 +22,28 @@ struct etr_flat_buf {
>  };
>  
>  /*
> + * etr_perf_buffer - Perf buffer used for ETR
> + * @etr_buf		- Actual buffer used by the ETR
> + * @snaphost		- Perf session mode
> + * @head		- handle->head at the beginning of the session.
> + * @nr_pages		- Number of pages in the ring buffer.
> + * @pages		- Array of Pages in the ring buffer.
> + */
> +struct etr_perf_buffer {
> +	struct etr_buf		*etr_buf;
> +	bool			snapshot;
> +	unsigned long		head;
> +	int			nr_pages;
> +	void			**pages;
> +};
> +
> +/* Convert the perf index to an offset within the ETR buffer */
> +#define PERF_IDX2OFF(idx, buf)	((idx) % ((buf)->nr_pages << PAGE_SHIFT))
> +
> +/* Lower limit for ETR hardware buffer */
> +#define TMC_ETR_PERF_MIN_BUF_SIZE	SZ_1M
> +
> +/*
>   * The TMC ETR SG has a page size of 4K. The SG table contains pointers
>   * to 4KB buffers. However, the OS may use a PAGE_SIZE different from
>   * 4K (i.e, 16KB or 64KB). This implies that a single OS page could
> @@ -1103,10 +1126,228 @@ static int tmc_enable_etr_sink_sysfs(struct coresight_device *csdev)
>  	return ret;
>  }
>  
> +/*
> + * tmc_etr_setup_perf_buf: Allocate ETR buffer for use by perf.
> + * The size of the hardware buffer is dependent on the size configured
> + * via sysfs and the perf ring buffer size. We prefer to allocate the
> + * largest possible size, scaling down the size by half until it
> + * reaches a minimum limit (1M), beyond which we give up.
> + */
> +static struct etr_perf_buffer *
> +tmc_etr_setup_perf_buf(struct tmc_drvdata *drvdata, int node, int nr_pages,
> +		       void **pages, bool snapshot)
> +{
> +	struct etr_buf *etr_buf;
> +	struct etr_perf_buffer *etr_perf;
> +	unsigned long size;
> +
> +	etr_perf = kzalloc_node(sizeof(*etr_perf), GFP_KERNEL, node);
> +	if (!etr_perf)
> +		return ERR_PTR(-ENOMEM);
> +
> +	/*
> +	 * Try to match the perf ring buffer size if it is larger
> +	 * than the size requested via sysfs.
> +	 */
> +	if ((nr_pages << PAGE_SHIFT) > drvdata->size) {
> +		etr_buf = tmc_alloc_etr_buf(drvdata, (nr_pages << PAGE_SHIFT),
> +					    0, node, NULL);
> +		if (!IS_ERR(etr_buf))
> +			goto done;
> +	}
> +
> +	/*
> +	 * Else switch to configured size for this ETR
> +	 * and scale down until we hit the minimum limit.
> +	 */
> +	size = drvdata->size;
> +	do {
> +		etr_buf = tmc_alloc_etr_buf(drvdata, size, 0, node, NULL);
> +		if (!IS_ERR(etr_buf))
> +			goto done;
> +		size /= 2;
> +	} while (size >= TMC_ETR_PERF_MIN_BUF_SIZE);
> +
> +	kfree(etr_perf);
> +	return ERR_PTR(-ENOMEM);
> +
> +done:
> +	etr_perf->etr_buf = etr_buf;
> +	return etr_perf;
> +}
> +
> +
> +static void *tmc_etr_alloc_perf_buffer(struct coresight_device *csdev,
> +				       int cpu, void **pages, int nr_pages,
> +				       bool snapshot)
> +{
> +	struct etr_perf_buffer *etr_perf;
> +	struct tmc_drvdata *drvdata = dev_get_drvdata(csdev->dev.parent);
> +
> +	if (cpu == -1)
> +		cpu = smp_processor_id();
> +
> +	etr_perf = tmc_etr_setup_perf_buf(drvdata, cpu_to_node(cpu),
> +					  nr_pages, pages, snapshot);
> +	if (IS_ERR(etr_perf)) {
> +		dev_dbg(drvdata->dev, "Unable to allocate ETR buffer\n");
> +		return NULL;
> +	}
> +
> +	etr_perf->snapshot = snapshot;
> +	etr_perf->nr_pages = nr_pages;
> +	etr_perf->pages = pages;
> +
> +	return etr_perf;
> +}
> +
> +static void tmc_etr_free_perf_buffer(void *config)
> +{
> +	struct etr_perf_buffer *etr_perf = config;
> +
> +	if (etr_perf->etr_buf)
> +		tmc_free_etr_buf(etr_perf->etr_buf);
> +	kfree(etr_perf);
> +}
> +
> +/*
> + * tmc_etr_sync_perf_buffer: Copy the actual trace data from the hardware
> + * buffer to the perf ring buffer.
> + */
> +static void tmc_etr_sync_perf_buffer(struct etr_perf_buffer *etr_perf)
> +{
> +	long bytes, to_copy;
> +	long pg_idx, pg_offset, src_offset;
> +	unsigned long head = etr_perf->head;
> +	char **dst_pages, *src_buf;
> +	struct etr_buf *etr_buf = etr_perf->etr_buf;
> +
> +	head = etr_perf->head;
> +	pg_idx = head >> PAGE_SHIFT;
> +	pg_offset = head & (PAGE_SIZE - 1);
> +	dst_pages = (char **)etr_perf->pages;
> +	src_offset = etr_buf->offset;
> +	to_copy = etr_buf->len;
> +
> +	while (to_copy > 0) {
> +		/*
> +		 * In one iteration, we can copy minimum of :
> +		 *  1) what is available in the source buffer,
> +		 *  2) what is available in the source buffer, before it
> +		 *     wraps around.
> +		 *  3) what is available in the destination page.
> +		 * in one iteration.
> +		 */
> +		bytes = tmc_etr_buf_get_data(etr_buf, src_offset, to_copy,
> +					     &src_buf);
> +		if (WARN_ON_ONCE(bytes <= 0))
> +			break;
> +		bytes = min(bytes, (long)(PAGE_SIZE - pg_offset));
> +
> +		memcpy(dst_pages[pg_idx] + pg_offset, src_buf, bytes);
> +
> +		to_copy -= bytes;
> +
> +		/* Move destination pointers */
> +		pg_offset += bytes;
> +		if (pg_offset == PAGE_SIZE) {
> +			pg_offset = 0;
> +			if (++pg_idx == etr_perf->nr_pages)
> +				pg_idx = 0;
> +		}
> +
> +		/* Move source pointers */
> +		src_offset += bytes;
> +		if (src_offset >= etr_buf->size)
> +			src_offset -= etr_buf->size;
> +	}
> +}
> +
> +/*
> + * tmc_etr_update_perf_buffer : Update the perf ring buffer with the
> + * available trace data. We use software double buffering at the moment.
> + *
> + * TODO: Add support for reusing the perf ring buffer.
> + */
> +static unsigned long
> +tmc_etr_update_perf_buffer(struct coresight_device *csdev,
> +			   struct perf_output_handle *handle,
> +			   void *config)
> +{
> +	bool lost = false;
> +	unsigned long flags, size = 0;
> +	struct tmc_drvdata *drvdata = dev_get_drvdata(csdev->dev.parent);
> +	struct etr_perf_buffer *etr_perf = config;
> +	struct etr_buf *etr_buf = etr_perf->etr_buf;
> +
> +	spin_lock_irqsave(&drvdata->spinlock, flags);
> +	if (WARN_ON(drvdata->perf_data != etr_perf)) {
> +		lost = true;
> +		spin_unlock_irqrestore(&drvdata->spinlock, flags);
> +		goto out;
> +	}
> +
> +	CS_UNLOCK(drvdata->base);
> +
> +	tmc_flush_and_stop(drvdata);
> +	tmc_sync_etr_buf(drvdata);
> +
> +	CS_UNLOCK(drvdata->base);

This is a copy/paste oversight, here you want to lock again.

> +	/* Reset perf specific data */
> +	drvdata->perf_data = NULL;
> +	spin_unlock_irqrestore(&drvdata->spinlock, flags);
> +
> +	size = etr_buf->len;
> +	tmc_etr_sync_perf_buffer(etr_perf);
> +
> +	/*
> +	 * Update handle->head in snapshot mode. Also update the size to the
> +	 * hardware buffer size if there was an overflow.
> +	 */
> +	if (etr_perf->snapshot) {
> +		handle->head += size;
> +		if (etr_buf->full)
> +			size = etr_buf->size;
> +	}
> +
> +	lost |= etr_buf->full;
> +out:
> +	if (lost)
> +		perf_aux_output_flag(handle, PERF_AUX_FLAG_TRUNCATED);
> +	return size;
> +}
> +
>  static int tmc_enable_etr_sink_perf(struct coresight_device *csdev, void *data)
>  {
> -	/* We don't support perf mode yet ! */
> -	return -EINVAL;
> +	int rc = 0;
> +	unsigned long flags;
> +	struct tmc_drvdata *drvdata = dev_get_drvdata(csdev->dev.parent);
> +	struct perf_output_handle *handle = data;
> +	struct etr_perf_buffer *etr_perf = etm_perf_sink_config(handle);
> +
> +	spin_lock_irqsave(&drvdata->spinlock, flags);
> +	/*
> +	 * There can be only one writer per sink in perf mode. If the sink
> +	 * is already open in SYSFS mode, we can't use it.
> +	 */
> +	if (drvdata->mode != CS_MODE_DISABLED || drvdata->perf_data) {
> +		rc = -EBUSY;
> +		goto unlock_out;
> +	}
> +
> +	if (WARN_ON(!etr_perf || !etr_perf->etr_buf)) {
> +		rc = -EINVAL;
> +		goto unlock_out;
> +	}
> +
> +	etr_perf->head = PERF_IDX2OFF(handle->head, etr_perf);
> +	drvdata->perf_data = etr_perf;
> +	drvdata->mode = CS_MODE_PERF;
> +	tmc_etr_enable_hw(drvdata, etr_perf->etr_buf);
> +
> +unlock_out:
> +	spin_unlock_irqrestore(&drvdata->spinlock, flags);
> +	return rc;
>  }
>  
>  static int tmc_enable_etr_sink(struct coresight_device *csdev,
> @@ -1148,6 +1389,9 @@ static void tmc_disable_etr_sink(struct coresight_device *csdev)
>  static const struct coresight_ops_sink tmc_etr_sink_ops = {
>  	.enable		= tmc_enable_etr_sink,
>  	.disable	= tmc_disable_etr_sink,
> +	.alloc_buffer	= tmc_etr_alloc_perf_buffer,
> +	.update_buffer	= tmc_etr_update_perf_buffer,
> +	.free_buffer	= tmc_etr_free_perf_buffer,


	.alloc_buffer	= tmc_alloc_etr_buffer,
	.update_buffer	= tmc_update_etr_buffer,
	.free_buffer	= tmc_free_etr_buffer,

To be consistant with .enable and .disable along with the naming convention on
the ETF side.

>  };
>  
>  const struct coresight_ops tmc_etr_cs_ops = {
> diff --git a/drivers/hwtracing/coresight/coresight-tmc.h b/drivers/hwtracing/coresight/coresight-tmc.h
> index 872f63e..487c537 100644
> --- a/drivers/hwtracing/coresight/coresight-tmc.h
> +++ b/drivers/hwtracing/coresight/coresight-tmc.h
> @@ -170,6 +170,7 @@ struct etr_buf {
>   * @trigger_cntr: amount of words to store after a trigger.
>   * @etr_caps:	Bitmask of capabilities of the TMC ETR, inferred from the
>   *		device configuration register (DEVID)
> + * @perf_data:	PERF buffer for ETR.
>   * @sysfs_data:	SYSFS buffer for ETR.
>   */
>  struct tmc_drvdata {
> @@ -191,6 +192,7 @@ struct tmc_drvdata {
>  	u32			trigger_cntr;
>  	u32			etr_caps;
>  	struct etr_buf		*sysfs_buf;
> +	void			*perf_data;
>  };
>  
>  struct etr_buf_operations {
> -- 
> 2.7.4
> 

  reply	other threads:[~2018-07-19 19:59 UTC|newest]

Thread overview: 44+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2018-07-17 17:11 [PATCH v2 00/10] coresight: perf: Support for tmc-etr backed buffers Suzuki K Poulose
2018-07-17 17:11 ` Suzuki K Poulose
2018-07-17 17:11 ` [PATCH v2 01/10] coresight: Fix handling of sinks Suzuki K Poulose
2018-07-17 17:11   ` Suzuki K Poulose
2018-07-17 17:11 ` [PATCH v2 02/10] coresight: perf: Fix per cpu path management Suzuki K Poulose
2018-07-17 17:11   ` Suzuki K Poulose
2018-07-17 17:11 ` [PATCH v2 03/10] coresight: perf: Disable trace path upon source error Suzuki K Poulose
2018-07-17 17:11   ` Suzuki K Poulose
2018-07-17 17:11 ` [PATCH v2 04/10] coresight: tmc-etr: Handle driver mode specific ETR buffers Suzuki K Poulose
2018-07-17 17:11   ` Suzuki K Poulose
2018-07-17 17:11 ` [PATCH v2 05/10] coresight: tmc-etr: Relax collection of trace from sysfs mode Suzuki K Poulose
2018-07-17 17:11   ` Suzuki K Poulose
2018-07-17 17:11 ` [PATCH v2 06/10] coresight: Convert driver messages to dev_dbg Suzuki K Poulose
2018-07-17 17:11   ` Suzuki K Poulose
2018-07-17 17:11 ` [PATCH v2 07/10] coresight: perf: Remove reset_buffer call back for sinks Suzuki K Poulose
2018-07-17 17:11   ` Suzuki K Poulose
2018-07-17 17:11 ` [PATCH v2 08/10] coresight: perf: Add helper to retrieve sink configuration Suzuki K Poulose
2018-07-17 17:11   ` Suzuki K Poulose
2018-07-19 20:07   ` Mathieu Poirier
2018-07-19 20:07     ` Mathieu Poirier
2018-07-20  8:43     ` Suzuki K Poulose
2018-07-20  8:43       ` Suzuki K Poulose
2018-07-23 16:50       ` Mathieu Poirier
2018-07-23 16:50         ` Mathieu Poirier
2018-07-17 17:11 ` [PATCH v2 09/10] coresight: perf: Remove set_buffer call back Suzuki K Poulose
2018-07-17 17:11   ` Suzuki K Poulose
2018-07-19 20:36   ` Mathieu Poirier
2018-07-19 20:36     ` Mathieu Poirier
2018-07-20  9:04     ` Suzuki K Poulose
2018-07-20  9:04       ` Suzuki K Poulose
2018-07-23 18:22       ` Mathieu Poirier
2018-07-23 18:22         ` Mathieu Poirier
2018-07-23 22:28         ` Suzuki K Poulose
2018-07-23 22:28           ` Suzuki K Poulose
2018-07-24 20:08           ` Mathieu Poirier
2018-07-24 20:08             ` Mathieu Poirier
2018-07-25  9:51             ` Suzuki K Poulose
2018-07-25  9:51               ` Suzuki K Poulose
2018-07-17 17:11 ` [PATCH v2 10/10] coresight: etm-perf: Add support for ETR backend Suzuki K Poulose
2018-07-17 17:11   ` Suzuki K Poulose
2018-07-19 19:59   ` Mathieu Poirier [this message]
2018-07-19 19:59     ` Mathieu Poirier
2018-07-20  9:07     ` Suzuki K Poulose
2018-07-20  9:07       ` Suzuki K Poulose

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20180719195949.GA9421@xps15 \
    --to=mathieu.poirier@linaro.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.