[PATCH 5/5] mfd: lochnagar: Add initial binding documentation

[Charles Keepax <ckeepax@opensource.cirrus.com>]

Lochnagar is an evaluation and development board for Cirrus
Logic Smart CODEC and Amp devices. It allows the connection of
most Cirrus Logic devices on mini-cards, as well as allowing
connection of various application processor systems to provide a
full evaluation platform.

Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
---
 .../devicetree/bindings/mfd/cirrus,lochnagar.txt   | 230 +++++++++++++++++++++
 1 file changed, 230 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/mfd/cirrus,lochnagar.txt

diff --git a/Documentation/devicetree/bindings/mfd/cirrus,lochnagar.txt b/Documentation/devicetree/bindings/mfd/cirrus,lochnagar.txt
new file mode 100644
index 000000000000..3382a14c19fe
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/cirrus,lochnagar.txt
@@ -0,0 +1,230 @@
+Cirrus Logic Lochnagar Audio Development Board
+
+Lochnagar is an evaluation and development board for Cirrus Logic
+Smart CODEC and Amp devices. It allows the connection of most Cirrus
+Logic devices on mini-cards, as well as allowing connection of
+various application processor systems to provide a full evaluation
+platform.  Audio system topology, clocking and power can all be
+controlled through the Lochnagar, allowing the device under test
+to be used in a variety of possible use cases.
+
+Also see these documents for generic binding information:
+  [1] GPIO : ../gpio/gpio.txt
+  [2] Pinctrl: ../pinctrl/pinctrl-bindings.txt
+  [3] Clock : ../clock/clock-bindings.txt
+  [4] Regulator: ../regulator/regulator.txt
+
+And these for relevant defines:
+  [5] include/dt-bindings/pinctrl/lochnagar.h
+  [6] include/dt-bindings/clock/lochnagar.h
+
+Required properties:
+
+  - compatible : One of the following strings:
+                 "cirrus,lochnagar1"
+                 "cirrus,lochnagar2"
+
+  - reg : I2C slave address
+
+  - gpio-controller : Indicates this device is a GPIO controller.
+  - #gpio-cells : Must be 2. The first cell is the pin number, see
+    [5] for available pins and the second cell is used to specify
+    optional parameters, see [1].
+  - gpio-ranges : Range of pins managed by the GPIO controller, see
+    [1]. Both the GPIO and Pinctrl base should be set to zero and the
+    count to the appropriate of the LOCHNAGARx_PIN_NUM_GPIOS define,
+    see [5].
+
+  - reset-gpios : Reset line to the Lochnagar, see [1].
+
+  - #clock-cells : Must be 1. The first cell indicates the clock
+    number, see [6] for available clocks and [3].
+
+  - pinctrl-names : A pinctrl state named "default" must be defined.
+  - pinctrl-0 : A phandle to the default pinctrl state.
+
+  - SYSVDD-supply: Primary power supply for the Lochnagar.
+
+Optional properties:
+
+  - present-gpios : Host present line, indicating the presence of a
+    host system, see [1]. This can be omitted if the present line is
+    tied in hardware.
+
+  - clocks : Must contain an entry for each clock in clock-names.
+  - clock-names : May contain entries for each of the following
+    clocks:
+     - ln-cdc-clkout : Output clock from CODEC card.
+     - ln-dsp-clkout : Output clock from DSP card.
+     - ln-gf-mclk1,ln-gf-mclk2,ln-gf-mclk3,ln-gf-mclk4 : Optional
+       input audio clocks from host system.
+     - ln-psia1-mclk, ln-psia2-mclk : Optional input audio clocks from
+       external connector.
+     - ln-spdif-clkout : Optional input audio clock from SPDIF.
+     - ln-adat-clkout : Optional input audio clock from ADAT.
+
+  - assigned-clocks : A list of Lochnagar clocks to be reparented, see
+    [6] for available clocks.
+  - assigned-clock-parents : Parents to be assigned to the clocks
+    listed in "assigned-clocks".
+
+  - MICBIAS1-supply, MICBIAS2-supply: Regulator supplies for the
+    MICxVDD outputs, supplying the digital microphones, normally
+    supplied from the attached CODEC.
+
+Required sub-nodes:
+
+The pin configurations are defined as a child of the pinctrl states
+node, see [2]. Each sub-node can have the following properties:
+  - groups : A list of groups to select (either this or "pins" must be
+    specified), available groups:
+      codec-aif1, codec-aif2, codec-aif3, dsp-aif1, dsp-aif2, psia1,
+      psia2, gf-aif1, gf-aif2, gf-aif3, gf-aif4, spdif-aif, usb-aif1,
+      usb-aif2, adat-aif, soundcard-aif
+  - pins : A list of pin names to select (either this or "groups" must
+    be specified), available pins:
+      fgpa-gpio1, fgpa-gpio2, fgpa-gpio3, fgpa-gpio4, fgpa-gpio5,
+      fgpa-gpio6, codec-gpio1, codec-gpio2, codec-gpio3, codec-gpio4,
+      codec-gpio5, codec-gpio6, codec-gpio7, codec-gpio8, dsp-gpio1,
+      dsp-gpio2, dsp-gpio3, dsp-gpio4, dsp-gpio5, dsp-gpio6, gf-gpio2,
+      gf-gpio3, gf-gpio7, codec-aif1-bclk, codec-aif1-rxdat,
+      codec-aif1-lrclk, codec-aif1-txdat, codec-aif2-bclk,
+      codec-aif2-rxdat, codec-aif2-lrclk, codec-aif2-txdat,
+      codec-aif3-bclk, codec-aif3-rxdat, codec-aif3-lrclk,
+      codec-aif3-txdat, dsp-aif1-bclk, dsp-aif1-rxdat, dsp-aif1-lrclk,
+      dsp-aif1-txdat, dsp-aif2-bclk, dsp-aif2-rxdat,
+      dsp-aif2-lrclk, dsp-aif2-txdat, psia1-bclk, psia1-rxdat,
+      psia1-lrclk, psia1-txdat, psia2-bclk, psia2-rxdat, psia2-lrclk,
+      psia2-txdat, gf-aif3-bclk, gf-aif3-rxdat, gf-aif3-lrclk,
+      gf-aif3-txdat, gf-aif4-bclk, gf-aif4-rxdat, gf-aif4-lrclk,
+      gf-aif4-txdat, gf-aif1-bclk, gf-aif1-rxdat, gf-aif1-lrclk,
+      gf-aif1-txdat, gf-aif2-bclk, gf-aif2-rxdat, gf-aif2-lrclk,
+      gf-aif2-txdat, dsp-uart1-rx, dsp-uart1-tx, dsp-uart2-rx,
+      dsp-uart2-tx, gf-uart2-rx, gf-uart2-tx, usb-uart-rx,
+      codec-pdmclk1, codec-pdmdat1, codec-pdmclk2, codec-pdmdat2,
+      codec-dmicclk1, codec-dmicdat1, codec-dmicclk2, codec-dmicdat2,
+      codec-dmicclk3, codec-dmicdat3, codec-dmicclk4, codec-dmicdat4,
+      dsp-dmicclk1, dsp-dmicdat1, dsp-dmicclk2, dsp-dmicdat2, i2c2-scl,
+      i2c2-sda, i2c3-scl, i2c3-sda, i2c4-scl, i2c4-sda, dsp-standby,
+      codec-mclk1, codec-mclk2, dsp-clkin, psia1-mclk, psia2-mclk,
+      gf-gpio1, gf-gpio5, dsp-gpio20, led1, led2
+  - function : The mux function to select, available functions:
+      aif, fgpa-gpio1, fgpa-gpio2, fgpa-gpio3, fgpa-gpio4, fgpa-gpio5,
+      fgpa-gpio6, codec-gpio1, codec-gpio2, codec-gpio3, codec-gpio4,
+      codec-gpio5, codec-gpio6, codec-gpio7, codec-gpio8, dsp-gpio1,
+      dsp-gpio2, dsp-gpio3, dsp-gpio4, dsp-gpio5, dsp-gpio6, gf-gpio2,
+      gf-gpio3, gf-gpio7, gf-gpio1, gf-gpio5, dsp-gpio20, codec-clkout,
+      dsp-clkout, pmic-32k, spdif-clkout, clk-12m288, clk-11m2986,
+      clk-24m576, clk-22m5792, xmos-mclk, gf-clkout1, gf-mclk1,
+      gf-mclk3, gf-mclk2, gf-clkout2, codec-mclk1, codec-mclk2,
+      dsp-clkin, psia1-mclk, psia2-mclk, spdif-mclk, codec-irq,
+      codec-reset, dsp-reset, dsp-irq, dsp-standby, codec-pdmclk1,
+      codec-pdmdat1, codec-pdmclk2, codec-pdmdat2, codec-dmicclk1,
+      codec-dmicdat1, codec-dmicclk2, codec-dmicdat2, codec-dmicclk3,
+      codec-dmicdat3, codec-dmicclk4, codec-dmicdat4, dsp-dmicclk1,
+      dsp-dmicdat1, dsp-dmicclk2, dsp-dmicdat2, dsp-uart1-rx,
+      dsp-uart1-tx, dsp-uart2-rx, dsp-uart2-tx, gf-uart2-rx,
+      gf-uart2-tx, usb-uart-rx, usb-uart-tx, i2c2-scl, i2c2-sda,
+      i2c3-scl, i2c3-sda, i2c4-scl, i2c4-sda, gpio, spdif-aif, psia1,
+      psia1-bclk, psia1-lrclk, psia1-rxdat, psia1-txdat, psia2,
+      psia2-bclk, psia2-lrclk, psia2-rxdat, psia2-txdat, codec-aif1,
+      codec-aif1-bclk, codec-aif1-lrclk, codec-aif1-rxdat,
+      codec-aif1-txdat, codec-aif2, codec-aif2-bclk, codec-aif2-lrclk,
+      codec-aif2-rxdat, codec-aif2-txdat, codec-aif3, codec-aif3-bclk,
+      codec-aif3-lrclk, codec-aif3-rxdat, codec-aif3-txdat, dsp-aif1,
+      dsp-aif1-bclk, dsp-aif1-lrclk, dsp-aif1-rxdat, dsp-aif1-txdat,
+      dsp-aif2, dsp-aif2-bclk, dsp-aif2-lrclk, dsp-aif2-rxdat,
+      dsp-aif2-txdat, gf-aif3, gf-aif3-bclk, gf-aif3-lrclk,
+      gf-aif3-rxdat, gf-aif3-txdat, gf-aif4, gf-aif4-bclk,
+      gf-aif4-lrclk, gf-aif4-rxdat, gf-aif4-txdat, gf-aif1,
+      gf-aif1-bclk, gf-aif1-lrclk, gf-aif1-rxdat, gf-aif1-txdat,
+      gf-aif2, gf-aif2-bclk, gf-aif2-lrclk, gf-aif2-rxdat,
+      gf-aif2-txdat, usb-aif1, usb-aif2, adat-aif, soundcard-aif,
+
+  - aif-master : Specifies that an AIF group will be used as a master
+    interface (either this or aif-slave is required if a group is
+    being muxed to an AIF)
+  - aif-slave : Specifies that an AIF group will be used as a slave
+    interface (either this or aif-master is required if a group is
+    being muxed to an AIF)
+
+Optional sub-nodes:
+
+  - VDDCORE : Initialisation data for the VDDCORE regulator, which
+    supplies the CODECs digital core if it has no build regulator for that
+    purpose.
+
+  - MICVDD : Initialisation data for the MICVDD regulator, which
+    supplies the CODECs MICVDD.
+  - MIC1VDD, MIC2VDD : Initialisation data for the MICxVDD supplies.
+      Optional Properties:
+      - cirrus,micbias-input : A property selecting which of the CODEC
+        minicard micbias outputs should be used, valid values are 1 - 4.
+
+  - VDD1V8 : Recommended fixed regulator for the VDD1V8 regulator, which supplies the
+    CODECs analog and 1.8V digital supplies.
+      Required Properties:
+      - compatible : Should be set to "regulator-fixed"
+      - regulator-min-microvolt : Should be set to 1.8V
+      - regulator-max-microvolt : Should be set to 1.8V
+      - regulator-boot-on
+      - regulator-always-on
+      - vin-supply : Should be set to same supply as SYSVDD
+
+Example:
+lochnagar: lochnagar@22 {
+	compatible = "cirrus,lochnagar2";
+	reg = <0x22>;
+
+	gpio-controller;
+	#gpio-cells = <2>;
+	gpio-ranges = <&lochnagar 0 0 110>;
+
+	reset-gpio = <&gpio0 55 0>;
+	present-gpio = <&gpio0 60 0>;
+
+	#clock-cells = <1>;
+
+	clocks = <&clk_audio>;
+	clock-names = "ln-gf-mclk2";
+
+	assigned-clocks = <&lochnagar LOCHNAGAR_CDC_MCLK1>,
+			  <&lochnagar LOCHNAGAR_CDC_MCLK2>;
+	assigned-clock-parents = <&clk_audio>,
+				 <&lochnagar LOCHNAGAR_PMIC_32K>;
+
+	SYSVDD-supply = <&wallvdd>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pin_settings>;
+
+	pin_settings: pin_settings {
+		ap_aif {
+			aif-slave;
+			groups = "gf-aif1";
+			function = "codec-aif3";
+		};
+		codec_aif {
+			aif-master;
+			groups = "codec-aif3";
+			function = "gf-aif1";
+		};
+	};
+
+	lochnagar_micvdd: MICVDD {
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	lochnagar_vdd1v8: VDD1V8 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VDD1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+
+		vin-supply = <&wallvdd>;
+	};
+};
-- 
2.11.0