* [PATCH V8 0/2] clocksource: add gx6605s SOC system timer @ 2018-09-20 8:03 Guo Ren 2018-09-20 8:03 ` [PATCH V8 1/2] " Guo Ren 2018-09-20 8:03 ` [PATCH V8 2/2] dt-bindings: timer: gx6605s SOC timer Guo Ren 0 siblings, 2 replies; 7+ messages in thread From: Guo Ren @ 2018-09-20 8:03 UTC (permalink / raw) To: tglx, daniel.lezcano, robh+dt, mark.rutland, arnd Cc: linux-kernel, devicetree, c-sky_gcc_upstream, green.hu, Guo Ren - Dt-bindings documentation - timer-gx6605s driver Guo Ren (2): clocksource: add gx6605s SOC system timer dt-bindings: timer: gx6605s SOC timer .../bindings/timer/csky,gx6605s-timer.txt | 42 ++++++ drivers/clocksource/Kconfig | 8 ++ drivers/clocksource/Makefile | 1 + drivers/clocksource/timer-gx6605s.c | 150 +++++++++++++++++++++ 4 files changed, 201 insertions(+) create mode 100644 Documentation/devicetree/bindings/timer/csky,gx6605s-timer.txt create mode 100644 drivers/clocksource/timer-gx6605s.c -- 2.7.4 ^ permalink raw reply [flat|nested] 7+ messages in thread
* [PATCH V8 1/2] clocksource: add gx6605s SOC system timer 2018-09-20 8:03 [PATCH V8 0/2] clocksource: add gx6605s SOC system timer Guo Ren @ 2018-09-20 8:03 ` Guo Ren 2018-09-20 16:06 ` Daniel Lezcano 2018-09-20 8:03 ` [PATCH V8 2/2] dt-bindings: timer: gx6605s SOC timer Guo Ren 1 sibling, 1 reply; 7+ messages in thread From: Guo Ren @ 2018-09-20 8:03 UTC (permalink / raw) To: tglx, daniel.lezcano, robh+dt, mark.rutland, arnd Cc: linux-kernel, devicetree, c-sky_gcc_upstream, green.hu, Guo Ren Changelog: - Add License and Copyright - Use timer-of framework - Change name with upstream feedback - Use clksource_mmio framework Signed-off-by: Guo Ren <ren_guo@c-sky.com> --- drivers/clocksource/Kconfig | 8 ++ drivers/clocksource/Makefile | 1 + drivers/clocksource/timer-gx6605s.c | 150 ++++++++++++++++++++++++++++++++++++ 3 files changed, 159 insertions(+) create mode 100644 drivers/clocksource/timer-gx6605s.c diff --git a/drivers/clocksource/Kconfig b/drivers/clocksource/Kconfig index a11f4ba..6d0f18d 100644 --- a/drivers/clocksource/Kconfig +++ b/drivers/clocksource/Kconfig @@ -620,4 +620,12 @@ config RISCV_TIMER is accessed via both the SBI and the rdcycle instruction. This is required for all RISC-V systems. +config GX6605S_TIMER + bool "Gx6605s SOC system timer driver" + depends on CSKY + select CLKSRC_MMIO + select TIMER_OF + help + This option enables support for gx6605s SOC's timer. + endmenu diff --git a/drivers/clocksource/Makefile b/drivers/clocksource/Makefile index db51b24..dc5621d 100644 --- a/drivers/clocksource/Makefile +++ b/drivers/clocksource/Makefile @@ -79,3 +79,4 @@ obj-$(CONFIG_CLKSRC_ST_LPC) += clksrc_st_lpc.o obj-$(CONFIG_X86_NUMACHIP) += numachip.o obj-$(CONFIG_ATCPIT100_TIMER) += timer-atcpit100.o obj-$(CONFIG_RISCV_TIMER) += riscv_timer.o +obj-$(CONFIG_GX6605S_TIMER) += timer-gx6605s.o diff --git a/drivers/clocksource/timer-gx6605s.c b/drivers/clocksource/timer-gx6605s.c new file mode 100644 index 0000000..10194c9 --- /dev/null +++ b/drivers/clocksource/timer-gx6605s.c @@ -0,0 +1,150 @@ +// SPDX-License-Identifier: GPL-2.0 +// Copyright (C) 2018 Hangzhou C-SKY Microsystems co.,ltd. + +#include <linux/init.h> +#include <linux/interrupt.h> +#include <linux/sched_clock.h> + +#include "timer-of.h" + +#define CLKSRC_OFFSET 0x40 + +#define TIMER_STATUS 0x00 +#define TIMER_VALUE 0x04 +#define TIMER_CONTRL 0x10 +#define TIMER_CONFIG 0x20 +#define TIMER_DIV 0x24 +#define TIMER_INI 0x28 + +#define GX6605S_STATUS_CLR BIT(0) +#define GX6605S_CONTRL_RST BIT(0) +#define GX6605S_CONTRL_START BIT(1) +#define GX6605S_CONFIG_EN BIT(0) +#define GX6605S_CONFIG_IRQ_EN BIT(1) + +static irqreturn_t gx6605s_timer_interrupt(int irq, void *dev) +{ + struct clock_event_device *ce = (struct clock_event_device *) dev; + void __iomem *base = timer_of_base(to_timer_of(ce)); + + writel_relaxed(GX6605S_STATUS_CLR, base + TIMER_STATUS); + + ce->event_handler(ce); + + return IRQ_HANDLED; +} + +static int gx6605s_timer_set_oneshot(struct clock_event_device *ce) +{ + void __iomem *base = timer_of_base(to_timer_of(ce)); + + /* reset and stop counter */ + writel_relaxed(GX6605S_CONTRL_RST, base + TIMER_CONTRL); + + /* enable with irq and start */ + writel_relaxed(GX6605S_CONFIG_EN | GX6605S_CONFIG_IRQ_EN, base + TIMER_CONFIG); + + return 0; +} + +static int gx6605s_timer_set_next_event(unsigned long delta, struct clock_event_device *ce) +{ + void __iomem *base = timer_of_base(to_timer_of(ce)); + + /* use reset to pause timer */ + writel_relaxed(GX6605S_CONTRL_RST, base + TIMER_CONTRL); + + /* config next timeout value */ + writel_relaxed(ULONG_MAX - delta, base + TIMER_INI); + writel_relaxed(GX6605S_CONTRL_START, base + TIMER_CONTRL); + + return 0; +} + +static int gx6605s_timer_shutdown(struct clock_event_device *ce) +{ + void __iomem *base = timer_of_base(to_timer_of(ce)); + + writel_relaxed(0, base + TIMER_CONTRL); + writel_relaxed(0, base + TIMER_CONFIG); + + return 0; +} + +static struct timer_of to = { + .flags = TIMER_OF_IRQ | TIMER_OF_BASE | TIMER_OF_CLOCK, + .clkevt = { + .rating = 300, + .features = CLOCK_EVT_FEAT_DYNIRQ | + CLOCK_EVT_FEAT_ONESHOT, + .set_state_shutdown = gx6605s_timer_shutdown, + .set_state_oneshot = gx6605s_timer_set_oneshot, + .set_next_event = gx6605s_timer_set_next_event, + .cpumask = cpu_possible_mask, + }, + .of_irq = { + .handler = gx6605s_timer_interrupt, + .flags = IRQF_TIMER | IRQF_IRQPOLL, + }, +}; + +static u64 notrace gx6605s_sched_clock_read(void) +{ + void __iomem *base; + + base = timer_of_base(&to) + CLKSRC_OFFSET; + + return (u64) readl_relaxed(base + TIMER_VALUE); +} + +static void gx6605s_clkevt_init(void __iomem *base) +{ + writel_relaxed(0, base + TIMER_DIV); + writel_relaxed(0, base + TIMER_CONFIG); + + clockevents_config_and_register(&to.clkevt, timer_of_rate(&to), 2, ULONG_MAX); +} + +static int gx6605s_clksrc_init(void __iomem *base) +{ + writel_relaxed(0, base + TIMER_DIV); + writel_relaxed(0, base + TIMER_INI); + + writel_relaxed(GX6605S_CONTRL_RST, base + TIMER_CONTRL); + + writel_relaxed(GX6605S_CONFIG_EN, base + TIMER_CONFIG); + + writel_relaxed(GX6605S_CONTRL_START, base + TIMER_CONTRL); + + sched_clock_register(gx6605s_sched_clock_read, 32, timer_of_rate(&to)); + + return clocksource_mmio_init(base + TIMER_VALUE, "gx6605s", timer_of_rate(&to), + 200, 32, clocksource_mmio_readl_up); +} + +static int __init gx6605s_timer_init(struct device_node *np) +{ + int ret; + + /* + * The timer driver is for nationalchip gx6605s SOC and there are two same timer + * in gx6605s. We use one for clkevt and another for clksrc. + * + * The timer is mmio map to access, so we need give mmio addres in dts. + * + * It provides a 32bit countup timer and interrupt will be caused by count-overflow. + * So we need set-next-event by ULONG_MAX - delta in TIMER_INI reg. + * + * The counter at 0x0 offset is clock event. + * The counter at 0x40 offset is clock source. + * They are the same in hardware, just different used by driver. + */ + ret = timer_of_init(np, &to); + if (ret) + return ret; + + gx6605s_clkevt_init(timer_of_base(&to)); + + return gx6605s_clksrc_init(timer_of_base(&to) + CLKSRC_OFFSET); +} +TIMER_OF_DECLARE(csky_gx6605s_timer, "csky,gx6605s-timer", gx6605s_timer_init); -- 2.7.4 ^ permalink raw reply related [flat|nested] 7+ messages in thread
* Re: [PATCH V8 1/2] clocksource: add gx6605s SOC system timer 2018-09-20 8:03 ` [PATCH V8 1/2] " Guo Ren @ 2018-09-20 16:06 ` Daniel Lezcano 2018-09-20 23:31 ` Guo Ren 0 siblings, 1 reply; 7+ messages in thread From: Daniel Lezcano @ 2018-09-20 16:06 UTC (permalink / raw) To: Guo Ren, tglx, robh+dt, mark.rutland, arnd Cc: linux-kernel, devicetree, c-sky_gcc_upstream, green.hu On 20/09/2018 10:03, Guo Ren wrote: > Changelog: > - Add License and Copyright > - Use timer-of framework > - Change name with upstream feedback > - Use clksource_mmio framework > > Signed-off-by: Guo Ren <ren_guo@c-sky.com> > --- > drivers/clocksource/Kconfig | 8 ++ > drivers/clocksource/Makefile | 1 + > drivers/clocksource/timer-gx6605s.c | 150 ++++++++++++++++++++++++++++++++++++ > 3 files changed, 159 insertions(+) > create mode 100644 drivers/clocksource/timer-gx6605s.c > > diff --git a/drivers/clocksource/Kconfig b/drivers/clocksource/Kconfig > index a11f4ba..6d0f18d 100644 > --- a/drivers/clocksource/Kconfig > +++ b/drivers/clocksource/Kconfig > @@ -620,4 +620,12 @@ config RISCV_TIMER > is accessed via both the SBI and the rdcycle instruction. This is > required for all RISC-V systems. > > +config GX6605S_TIMER > + bool "Gx6605s SOC system timer driver" > + depends on CSKY > + select CLKSRC_MMIO > + select TIMER_OF > + help > + This option enables support for gx6605s SOC's timer. > + > endmenu Please make the option not visible as default. There are currently two approaches look at MTK_TIMER and SPRD_TIMER. Apart the two nits below, the driver looks fine. Thanks! -- Daniel > diff --git a/drivers/clocksource/Makefile b/drivers/clocksource/Makefile > index db51b24..dc5621d 100644 > --- a/drivers/clocksource/Makefile > +++ b/drivers/clocksource/Makefile > @@ -79,3 +79,4 @@ obj-$(CONFIG_CLKSRC_ST_LPC) += clksrc_st_lpc.o > obj-$(CONFIG_X86_NUMACHIP) += numachip.o > obj-$(CONFIG_ATCPIT100_TIMER) += timer-atcpit100.o > obj-$(CONFIG_RISCV_TIMER) += riscv_timer.o > +obj-$(CONFIG_GX6605S_TIMER) += timer-gx6605s.o > diff --git a/drivers/clocksource/timer-gx6605s.c b/drivers/clocksource/timer-gx6605s.c > new file mode 100644 > index 0000000..10194c9 > --- /dev/null > +++ b/drivers/clocksource/timer-gx6605s.c > @@ -0,0 +1,150 @@ > +// SPDX-License-Identifier: GPL-2.0 > +// Copyright (C) 2018 Hangzhou C-SKY Microsystems co.,ltd. > + > +#include <linux/init.h> > +#include <linux/interrupt.h> > +#include <linux/sched_clock.h> > + > +#include "timer-of.h" > + > +#define CLKSRC_OFFSET 0x40 > + > +#define TIMER_STATUS 0x00 > +#define TIMER_VALUE 0x04 > +#define TIMER_CONTRL 0x10 > +#define TIMER_CONFIG 0x20 > +#define TIMER_DIV 0x24 > +#define TIMER_INI 0x28 > + > +#define GX6605S_STATUS_CLR BIT(0) > +#define GX6605S_CONTRL_RST BIT(0) > +#define GX6605S_CONTRL_START BIT(1) > +#define GX6605S_CONFIG_EN BIT(0) > +#define GX6605S_CONFIG_IRQ_EN BIT(1) > + > +static irqreturn_t gx6605s_timer_interrupt(int irq, void *dev) > +{ > + struct clock_event_device *ce = (struct clock_event_device *) dev; nit: no cast is needed. > + void __iomem *base = timer_of_base(to_timer_of(ce)); > + > + writel_relaxed(GX6605S_STATUS_CLR, base + TIMER_STATUS); > + > + ce->event_handler(ce); > + > + return IRQ_HANDLED; > +} > + > +static int gx6605s_timer_set_oneshot(struct clock_event_device *ce) > +{ > + void __iomem *base = timer_of_base(to_timer_of(ce)); > + > + /* reset and stop counter */ > + writel_relaxed(GX6605S_CONTRL_RST, base + TIMER_CONTRL); > + > + /* enable with irq and start */ > + writel_relaxed(GX6605S_CONFIG_EN | GX6605S_CONFIG_IRQ_EN, base + TIMER_CONFIG); > + > + return 0; > +} > + > +static int gx6605s_timer_set_next_event(unsigned long delta, struct clock_event_device *ce) > +{ > + void __iomem *base = timer_of_base(to_timer_of(ce)); > + > + /* use reset to pause timer */ > + writel_relaxed(GX6605S_CONTRL_RST, base + TIMER_CONTRL); > + > + /* config next timeout value */ > + writel_relaxed(ULONG_MAX - delta, base + TIMER_INI); > + writel_relaxed(GX6605S_CONTRL_START, base + TIMER_CONTRL); > + > + return 0; > +} > + > +static int gx6605s_timer_shutdown(struct clock_event_device *ce) > +{ > + void __iomem *base = timer_of_base(to_timer_of(ce)); > + > + writel_relaxed(0, base + TIMER_CONTRL); > + writel_relaxed(0, base + TIMER_CONFIG); > + > + return 0; > +} > + > +static struct timer_of to = { > + .flags = TIMER_OF_IRQ | TIMER_OF_BASE | TIMER_OF_CLOCK, > + .clkevt = { > + .rating = 300, > + .features = CLOCK_EVT_FEAT_DYNIRQ | > + CLOCK_EVT_FEAT_ONESHOT, > + .set_state_shutdown = gx6605s_timer_shutdown, > + .set_state_oneshot = gx6605s_timer_set_oneshot, > + .set_next_event = gx6605s_timer_set_next_event, > + .cpumask = cpu_possible_mask, > + }, > + .of_irq = { > + .handler = gx6605s_timer_interrupt, > + .flags = IRQF_TIMER | IRQF_IRQPOLL, > + }, > +}; > + > +static u64 notrace gx6605s_sched_clock_read(void) > +{ > + void __iomem *base; > + > + base = timer_of_base(&to) + CLKSRC_OFFSET; > + > + return (u64) readl_relaxed(base + TIMER_VALUE); nit: extra space after '(u64)' > +} > + > +static void gx6605s_clkevt_init(void __iomem *base) > +{ > + writel_relaxed(0, base + TIMER_DIV); > + writel_relaxed(0, base + TIMER_CONFIG); > + > + clockevents_config_and_register(&to.clkevt, timer_of_rate(&to), 2, ULONG_MAX); > +} > + > +static int gx6605s_clksrc_init(void __iomem *base) > +{ > + writel_relaxed(0, base + TIMER_DIV); > + writel_relaxed(0, base + TIMER_INI); > + > + writel_relaxed(GX6605S_CONTRL_RST, base + TIMER_CONTRL); > + > + writel_relaxed(GX6605S_CONFIG_EN, base + TIMER_CONFIG); > + > + writel_relaxed(GX6605S_CONTRL_START, base + TIMER_CONTRL); > + > + sched_clock_register(gx6605s_sched_clock_read, 32, timer_of_rate(&to)); > + > + return clocksource_mmio_init(base + TIMER_VALUE, "gx6605s", timer_of_rate(&to), > + 200, 32, clocksource_mmio_readl_up); > +} > + > +static int __init gx6605s_timer_init(struct device_node *np) > +{ > + int ret; > + > + /* > + * The timer driver is for nationalchip gx6605s SOC and there are two same timer > + * in gx6605s. We use one for clkevt and another for clksrc. > + * > + * The timer is mmio map to access, so we need give mmio addres in dts. > + * > + * It provides a 32bit countup timer and interrupt will be caused by count-overflow. > + * So we need set-next-event by ULONG_MAX - delta in TIMER_INI reg. > + * > + * The counter at 0x0 offset is clock event. > + * The counter at 0x40 offset is clock source. > + * They are the same in hardware, just different used by driver. > + */ > + ret = timer_of_init(np, &to); > + if (ret) > + return ret; > + > + gx6605s_clkevt_init(timer_of_base(&to)); > + > + return gx6605s_clksrc_init(timer_of_base(&to) + CLKSRC_OFFSET); > +} > +TIMER_OF_DECLARE(csky_gx6605s_timer, "csky,gx6605s-timer", gx6605s_timer_init); > -- <http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs Follow Linaro: <http://www.facebook.com/pages/Linaro> Facebook | <http://twitter.com/#!/linaroorg> Twitter | <http://www.linaro.org/linaro-blog/> Blog ^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH V8 1/2] clocksource: add gx6605s SOC system timer 2018-09-20 16:06 ` Daniel Lezcano @ 2018-09-20 23:31 ` Guo Ren 2018-09-20 23:57 ` Daniel Lezcano 0 siblings, 1 reply; 7+ messages in thread From: Guo Ren @ 2018-09-20 23:31 UTC (permalink / raw) To: Daniel Lezcano Cc: tglx, robh+dt, mark.rutland, arnd, linux-kernel, devicetree, c-sky_gcc_upstream, green.hu On Thu, Sep 20, 2018 at 06:06:19PM +0200, Daniel Lezcano wrote: > On 20/09/2018 10:03, Guo Ren wrote: > > Changelog: > > - Add License and Copyright > > - Use timer-of framework > > - Change name with upstream feedback > > - Use clksource_mmio framework > > > > Signed-off-by: Guo Ren <ren_guo@c-sky.com> > > --- > > drivers/clocksource/Kconfig | 8 ++ > > drivers/clocksource/Makefile | 1 + > > drivers/clocksource/timer-gx6605s.c | 150 ++++++++++++++++++++++++++++++++++++ > > 3 files changed, 159 insertions(+) > > create mode 100644 drivers/clocksource/timer-gx6605s.c > > > > diff --git a/drivers/clocksource/Kconfig b/drivers/clocksource/Kconfig > > index a11f4ba..6d0f18d 100644 > > --- a/drivers/clocksource/Kconfig > > +++ b/drivers/clocksource/Kconfig > > @@ -620,4 +620,12 @@ config RISCV_TIMER > > is accessed via both the SBI and the rdcycle instruction. This is > > required for all RISC-V systems. > > > > +config GX6605S_TIMER > > + bool "Gx6605s SOC system timer driver" > > + depends on CSKY > > + select CLKSRC_MMIO > > + select TIMER_OF > > + help > > + This option enables support for gx6605s SOC's timer. > > + > > endmenu > > Please make the option not visible as default. There are currently two > approaches look at MTK_TIMER and SPRD_TIMER. Em ... (ot sure why COMPILE_TEST?): bool "Gx6605s SOC system timer driver" if COMPILE_TEST Hmm? > > +static irqreturn_t gx6605s_timer_interrupt(int irq, void *dev) > > +{ > > + struct clock_event_device *ce = (struct clock_event_device *) dev; > > nit: no cast is needed. Yes, change to: struct clock_event_device *ce = dev; > > +static u64 notrace gx6605s_sched_clock_read(void) > > +{ > > + void __iomem *base; > > + > > + base = timer_of_base(&to) + CLKSRC_OFFSET; > > + > > + return (u64) readl_relaxed(base + TIMER_VALUE); > > nit: extra space after '(u64)' Ok return (u64)readl_relaxed(base + TIMER_VALUE); Best Regards Guo Ren ^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH V8 1/2] clocksource: add gx6605s SOC system timer 2018-09-20 23:31 ` Guo Ren @ 2018-09-20 23:57 ` Daniel Lezcano 2018-09-21 11:24 ` Guo Ren 0 siblings, 1 reply; 7+ messages in thread From: Daniel Lezcano @ 2018-09-20 23:57 UTC (permalink / raw) To: Guo Ren Cc: tglx, robh+dt, mark.rutland, arnd, linux-kernel, devicetree, c-sky_gcc_upstream, green.hu On 21/09/2018 01:31, Guo Ren wrote: > On Thu, Sep 20, 2018 at 06:06:19PM +0200, Daniel Lezcano wrote: >> On 20/09/2018 10:03, Guo Ren wrote: >>> Changelog: >>> - Add License and Copyright >>> - Use timer-of framework >>> - Change name with upstream feedback >>> - Use clksource_mmio framework >>> >>> Signed-off-by: Guo Ren <ren_guo@c-sky.com> >>> --- >>> drivers/clocksource/Kconfig | 8 ++ >>> drivers/clocksource/Makefile | 1 + >>> drivers/clocksource/timer-gx6605s.c | 150 ++++++++++++++++++++++++++++++++++++ >>> 3 files changed, 159 insertions(+) >>> create mode 100644 drivers/clocksource/timer-gx6605s.c >>> >>> diff --git a/drivers/clocksource/Kconfig b/drivers/clocksource/Kconfig >>> index a11f4ba..6d0f18d 100644 >>> --- a/drivers/clocksource/Kconfig >>> +++ b/drivers/clocksource/Kconfig >>> @@ -620,4 +620,12 @@ config RISCV_TIMER >>> is accessed via both the SBI and the rdcycle instruction. This is >>> required for all RISC-V systems. >>> >>> +config GX6605S_TIMER >>> + bool "Gx6605s SOC system timer driver" >>> + depends on CSKY >>> + select CLKSRC_MMIO >>> + select TIMER_OF >>> + help >>> + This option enables support for gx6605s SOC's timer. >>> + >>> endmenu >> >> Please make the option not visible as default. There are currently two >> approaches look at MTK_TIMER and SPRD_TIMER. > Em ... (ot sure why COMPILE_TEST?): > bool "Gx6605s SOC system timer driver" if COMPILE_TEST > Hmm? Because by enabling the COMPILE_TEST, you give the opportunity to someone without the hardware to cross-compile test your driver and catch errors very soon before the changes hit your tree. There are several Continuous Integration loop around running the latest changes in the kernel (kernelci, 01.org, etc ...) and all drivers with this flag are compiled tested. If the option is not set, the timer is silently selected by your platform's Kconfig only, without giving the opportunity to an non-expert user to unselect the timer leading to, maybe, an unbootable board. >>> +static irqreturn_t gx6605s_timer_interrupt(int irq, void *dev) >>> +{ >>> + struct clock_event_device *ce = (struct clock_event_device *) dev; >> >> nit: no cast is needed. > Yes, change to: > struct clock_event_device *ce = dev; > > >>> +static u64 notrace gx6605s_sched_clock_read(void) >>> +{ >>> + void __iomem *base; >>> + >>> + base = timer_of_base(&to) + CLKSRC_OFFSET; >>> + >>> + return (u64) readl_relaxed(base + TIMER_VALUE); >> >> nit: extra space after '(u64)' > Ok > return (u64)readl_relaxed(base + TIMER_VALUE); > > Best Regards > Guo Ren > -- <http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs Follow Linaro: <http://www.facebook.com/pages/Linaro> Facebook | <http://twitter.com/#!/linaroorg> Twitter | <http://www.linaro.org/linaro-blog/> Blog ^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH V8 1/2] clocksource: add gx6605s SOC system timer 2018-09-20 23:57 ` Daniel Lezcano @ 2018-09-21 11:24 ` Guo Ren 0 siblings, 0 replies; 7+ messages in thread From: Guo Ren @ 2018-09-21 11:24 UTC (permalink / raw) To: Daniel Lezcano Cc: tglx, robh+dt, mark.rutland, arnd, linux-kernel, devicetree, c-sky_gcc_upstream, green.hu On Fri, Sep 21, 2018 at 01:57:27AM +0200, Daniel Lezcano wrote: > On 21/09/2018 01:31, Guo Ren wrote: > > On Thu, Sep 20, 2018 at 06:06:19PM +0200, Daniel Lezcano wrote: > >> On 20/09/2018 10:03, Guo Ren wrote: > >>> Changelog: > >>> - Add License and Copyright > >>> - Use timer-of framework > >>> - Change name with upstream feedback > >>> - Use clksource_mmio framework > >>> > >>> Signed-off-by: Guo Ren <ren_guo@c-sky.com> > >>> --- > >>> drivers/clocksource/Kconfig | 8 ++ > >>> drivers/clocksource/Makefile | 1 + > >>> drivers/clocksource/timer-gx6605s.c | 150 ++++++++++++++++++++++++++++++++++++ > >>> 3 files changed, 159 insertions(+) > >>> create mode 100644 drivers/clocksource/timer-gx6605s.c > >>> > >>> diff --git a/drivers/clocksource/Kconfig b/drivers/clocksource/Kconfig > >>> index a11f4ba..6d0f18d 100644 > >>> --- a/drivers/clocksource/Kconfig > >>> +++ b/drivers/clocksource/Kconfig > >>> @@ -620,4 +620,12 @@ config RISCV_TIMER > >>> is accessed via both the SBI and the rdcycle instruction. This is > >>> required for all RISC-V systems. > >>> > >>> +config GX6605S_TIMER > >>> + bool "Gx6605s SOC system timer driver" > >>> + depends on CSKY > >>> + select CLKSRC_MMIO > >>> + select TIMER_OF > >>> + help > >>> + This option enables support for gx6605s SOC's timer. > >>> + > >>> endmenu > >> > >> Please make the option not visible as default. There are currently two > >> approaches look at MTK_TIMER and SPRD_TIMER. > > Em ... (ot sure why COMPILE_TEST?): > > bool "Gx6605s SOC system timer driver" if COMPILE_TEST > > Hmm? > > Because by enabling the COMPILE_TEST, you give the opportunity to > someone without the hardware to cross-compile test your driver and catch > errors very soon before the changes hit your tree. > > There are several Continuous Integration loop around running the latest > changes in the kernel (kernelci, 01.org, etc ...) and all drivers with > this flag are compiled tested. > > If the option is not set, the timer is silently selected by your > platform's Kconfig only, without giving the opportunity to an non-expert > user to unselect the timer leading to, maybe, an unbootable board. > I got it, thx for the reply. Best Regards Guo Ren ^ permalink raw reply [flat|nested] 7+ messages in thread
* [PATCH V8 2/2] dt-bindings: timer: gx6605s SOC timer 2018-09-20 8:03 [PATCH V8 0/2] clocksource: add gx6605s SOC system timer Guo Ren 2018-09-20 8:03 ` [PATCH V8 1/2] " Guo Ren @ 2018-09-20 8:03 ` Guo Ren 1 sibling, 0 replies; 7+ messages in thread From: Guo Ren @ 2018-09-20 8:03 UTC (permalink / raw) To: tglx, daniel.lezcano, robh+dt, mark.rutland, arnd Cc: linux-kernel, devicetree, c-sky_gcc_upstream, green.hu, Guo Ren - Dt-bindings doc for gx6605s SOC's system timer. Signed-off-by: Guo Ren <ren_guo@c-sky.com> Reviewed-by: Rob Herring <robh@kernel.org> --- .../bindings/timer/csky,gx6605s-timer.txt | 42 ++++++++++++++++++++++ 1 file changed, 42 insertions(+) create mode 100644 Documentation/devicetree/bindings/timer/csky,gx6605s-timer.txt diff --git a/Documentation/devicetree/bindings/timer/csky,gx6605s-timer.txt b/Documentation/devicetree/bindings/timer/csky,gx6605s-timer.txt new file mode 100644 index 0000000..6b04344 --- /dev/null +++ b/Documentation/devicetree/bindings/timer/csky,gx6605s-timer.txt @@ -0,0 +1,42 @@ +================= +gx6605s SOC Timer +================= + +The timer is used in gx6605s soc as system timer and the driver +contain clk event and clk source. + +============================== +timer node bindings definition +============================== + + Description: Describes gx6605s SOC timer + + PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: must be "csky,gx6605s-timer" + - reg + Usage: required + Value type: <u32 u32> + Definition: <phyaddr size> in soc from cpu view + - clocks + Usage: required + Value type: phandle + clock specifier cells + Definition: must be input clk node + - interrupt + Usage: required + Value type: <u32> + Definition: must be timer irq num defined by soc + +Examples: +--------- + + timer0: timer@20a000 { + compatible = "csky,gx6605s-timer"; + reg = <0x0020a000 0x400>; + clocks = <&dummy_apb_clk>; + interrupts = <10>; + interrupt-parent = <&intc>; + }; -- 2.7.4 ^ permalink raw reply related [flat|nested] 7+ messages in thread
end of thread, other threads:[~2018-09-21 11:24 UTC | newest] Thread overview: 7+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2018-09-20 8:03 [PATCH V8 0/2] clocksource: add gx6605s SOC system timer Guo Ren 2018-09-20 8:03 ` [PATCH V8 1/2] " Guo Ren 2018-09-20 16:06 ` Daniel Lezcano 2018-09-20 23:31 ` Guo Ren 2018-09-20 23:57 ` Daniel Lezcano 2018-09-21 11:24 ` Guo Ren 2018-09-20 8:03 ` [PATCH V8 2/2] dt-bindings: timer: gx6605s SOC timer Guo Ren
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.