* [PATCH] ARM: dts: exynos: Add CD and WP pins to Odroid XU SD card @ 2018-09-21 21:03 ` Krzysztof Kozlowski 0 siblings, 0 replies; 6+ messages in thread From: Krzysztof Kozlowski @ 2018-09-21 21:03 UTC (permalink / raw) To: Kukjin Kim, Krzysztof Kozlowski, devicetree, linux-arm-kernel, linux-samsung-soc, linux-kernel Cc: Marek Szyprowski, Anand Moon Defining card-detect and write-protect GPIO pins in Odroid XU SD Card does not change anything from functional point of view - dw-mmc driver was reading the state from registers. Adding cd-gpios and wp-gpios properties changes only internal driver behavior to access the pins directly. Add them to DTS only to comprehensively describe the hardware. Minor benefit is that write-protect pin configuration makes sure that it will be properly pulled up to indicate write access. This also removes debug messages: dwmmc_exynos 12220000.mmc: No GPIO consumer cd found dwmmc_exynos 12220000.mmc: No GPIO consumer wp found Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> --- arch/arm/boot/dts/exynos5410-odroidxu.dts | 12 +++++++++++- 1 file changed, 11 insertions(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/exynos5410-odroidxu.dts b/arch/arm/boot/dts/exynos5410-odroidxu.dts index a2046f5f998c..dae360f29a47 100644 --- a/arch/arm/boot/dts/exynos5410-odroidxu.dts +++ b/arch/arm/boot/dts/exynos5410-odroidxu.dts @@ -525,12 +525,14 @@ &mmc_2 { status = "okay"; + wp-gpios = <&gpm5 0 GPIO_ACTIVE_LOW>; + cd-gpios = <&gpc2 2 GPIO_ACTIVE_LOW>; card-detect-delay = <200>; samsung,dw-mshc-ciu-div = <3>; samsung,dw-mshc-sdr-timing = <0 4>; samsung,dw-mshc-ddr-timing = <0 2>; pinctrl-names = "default"; - pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus1 &sd2_bus4>; + pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus1 &sd2_bus4 &sd2_wp>; bus-width = <4>; cap-sd-highspeed; vmmc-supply = <&ldo21_reg>; @@ -573,6 +575,14 @@ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>; }; + + sd2_wp: sd2-wp { + samsung,pins = "gpm5-0"; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + /* Pin is floating so pull it up to disable write-protect */ + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>; + samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>; + }; }; &pwm { -- 2.17.1 ^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH] ARM: dts: exynos: Add CD and WP pins to Odroid XU SD card @ 2018-09-21 21:03 ` Krzysztof Kozlowski 0 siblings, 0 replies; 6+ messages in thread From: Krzysztof Kozlowski @ 2018-09-21 21:03 UTC (permalink / raw) To: linux-arm-kernel Defining card-detect and write-protect GPIO pins in Odroid XU SD Card does not change anything from functional point of view - dw-mmc driver was reading the state from registers. Adding cd-gpios and wp-gpios properties changes only internal driver behavior to access the pins directly. Add them to DTS only to comprehensively describe the hardware. Minor benefit is that write-protect pin configuration makes sure that it will be properly pulled up to indicate write access. This also removes debug messages: dwmmc_exynos 12220000.mmc: No GPIO consumer cd found dwmmc_exynos 12220000.mmc: No GPIO consumer wp found Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> --- arch/arm/boot/dts/exynos5410-odroidxu.dts | 12 +++++++++++- 1 file changed, 11 insertions(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/exynos5410-odroidxu.dts b/arch/arm/boot/dts/exynos5410-odroidxu.dts index a2046f5f998c..dae360f29a47 100644 --- a/arch/arm/boot/dts/exynos5410-odroidxu.dts +++ b/arch/arm/boot/dts/exynos5410-odroidxu.dts @@ -525,12 +525,14 @@ &mmc_2 { status = "okay"; + wp-gpios = <&gpm5 0 GPIO_ACTIVE_LOW>; + cd-gpios = <&gpc2 2 GPIO_ACTIVE_LOW>; card-detect-delay = <200>; samsung,dw-mshc-ciu-div = <3>; samsung,dw-mshc-sdr-timing = <0 4>; samsung,dw-mshc-ddr-timing = <0 2>; pinctrl-names = "default"; - pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus1 &sd2_bus4>; + pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus1 &sd2_bus4 &sd2_wp>; bus-width = <4>; cap-sd-highspeed; vmmc-supply = <&ldo21_reg>; @@ -573,6 +575,14 @@ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>; }; + + sd2_wp: sd2-wp { + samsung,pins = "gpm5-0"; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + /* Pin is floating so pull it up to disable write-protect */ + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>; + samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>; + }; }; &pwm { -- 2.17.1 ^ permalink raw reply related [flat|nested] 6+ messages in thread
* Re: [PATCH] ARM: dts: exynos: Add CD and WP pins to Odroid XU SD card 2018-09-21 21:03 ` Krzysztof Kozlowski @ 2018-09-24 10:04 ` Marek Szyprowski -1 siblings, 0 replies; 6+ messages in thread From: Marek Szyprowski @ 2018-09-24 10:04 UTC (permalink / raw) To: Krzysztof Kozlowski, Kukjin Kim, devicetree, linux-arm-kernel, linux-samsung-soc, linux-kernel Cc: Anand Moon Hi Krzysztof, On 2018-09-21 23:03, Krzysztof Kozlowski wrote: > Defining card-detect and write-protect GPIO pins in Odroid XU SD Card > does not change anything from functional point of view - dw-mmc driver > was reading the state from registers. Adding cd-gpios and wp-gpios > properties changes only internal driver behavior to access the pins > directly. > > Add them to DTS only to comprehensively describe the hardware. Minor > benefit is that write-protect pin configuration makes sure that it will > be properly pulled up to indicate write access. > > This also removes debug messages: > dwmmc_exynos 12220000.mmc: No GPIO consumer cd found > dwmmc_exynos 12220000.mmc: No GPIO consumer wp found > > Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> > --- > arch/arm/boot/dts/exynos5410-odroidxu.dts | 12 +++++++++++- > 1 file changed, 11 insertions(+), 1 deletion(-) > > diff --git a/arch/arm/boot/dts/exynos5410-odroidxu.dts b/arch/arm/boot/dts/exynos5410-odroidxu.dts > index a2046f5f998c..dae360f29a47 100644 > --- a/arch/arm/boot/dts/exynos5410-odroidxu.dts > +++ b/arch/arm/boot/dts/exynos5410-odroidxu.dts > @@ -525,12 +525,14 @@ > > &mmc_2 { > status = "okay"; > + wp-gpios = <&gpm5 0 GPIO_ACTIVE_LOW>; > + cd-gpios = <&gpc2 2 GPIO_ACTIVE_LOW>; > card-detect-delay = <200>; > samsung,dw-mshc-ciu-div = <3>; > samsung,dw-mshc-sdr-timing = <0 4>; > samsung,dw-mshc-ddr-timing = <0 2>; > pinctrl-names = "default"; > - pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus1 &sd2_bus4>; > + pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus1 &sd2_bus4 &sd2_wp>; IMHO there is no point adding cd-gpios property if CD line is already assigned to this device via respective pin ctrl entry (as special function). Handling of WP line is even more controversial imho. Ideally the drivers or mmc core should check somehow if WP line is available or not and act respectively. WP line is not available on uSD card connector so there is no point describing it. > bus-width = <4>; > cap-sd-highspeed; > vmmc-supply = <&ldo21_reg>; > @@ -573,6 +575,14 @@ > samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; > samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>; > }; > + > + sd2_wp: sd2-wp { > + samsung,pins = "gpm5-0"; > + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; > + /* Pin is floating so pull it up to disable write-protect */ > + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>; > + samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>; > + }; > }; > > &pwm { Best regards -- Marek Szyprowski, PhD Samsung R&D Institute Poland ^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH] ARM: dts: exynos: Add CD and WP pins to Odroid XU SD card @ 2018-09-24 10:04 ` Marek Szyprowski 0 siblings, 0 replies; 6+ messages in thread From: Marek Szyprowski @ 2018-09-24 10:04 UTC (permalink / raw) To: linux-arm-kernel Hi Krzysztof, On 2018-09-21 23:03, Krzysztof Kozlowski wrote: > Defining card-detect and write-protect GPIO pins in Odroid XU SD Card > does not change anything from functional point of view - dw-mmc driver > was reading the state from registers. Adding cd-gpios and wp-gpios > properties changes only internal driver behavior to access the pins > directly. > > Add them to DTS only to comprehensively describe the hardware. Minor > benefit is that write-protect pin configuration makes sure that it will > be properly pulled up to indicate write access. > > This also removes debug messages: > dwmmc_exynos 12220000.mmc: No GPIO consumer cd found > dwmmc_exynos 12220000.mmc: No GPIO consumer wp found > > Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> > --- > arch/arm/boot/dts/exynos5410-odroidxu.dts | 12 +++++++++++- > 1 file changed, 11 insertions(+), 1 deletion(-) > > diff --git a/arch/arm/boot/dts/exynos5410-odroidxu.dts b/arch/arm/boot/dts/exynos5410-odroidxu.dts > index a2046f5f998c..dae360f29a47 100644 > --- a/arch/arm/boot/dts/exynos5410-odroidxu.dts > +++ b/arch/arm/boot/dts/exynos5410-odroidxu.dts > @@ -525,12 +525,14 @@ > > &mmc_2 { > status = "okay"; > + wp-gpios = <&gpm5 0 GPIO_ACTIVE_LOW>; > + cd-gpios = <&gpc2 2 GPIO_ACTIVE_LOW>; > card-detect-delay = <200>; > samsung,dw-mshc-ciu-div = <3>; > samsung,dw-mshc-sdr-timing = <0 4>; > samsung,dw-mshc-ddr-timing = <0 2>; > pinctrl-names = "default"; > - pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus1 &sd2_bus4>; > + pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus1 &sd2_bus4 &sd2_wp>; IMHO there is no point adding cd-gpios property if CD line is already assigned to this device via respective pin ctrl entry (as special function). Handling of WP line is even more controversial imho. Ideally the drivers or mmc core should check somehow if WP line is available or not and act respectively. WP line is not available on uSD card connector so there is no point describing it. > bus-width = <4>; > cap-sd-highspeed; > vmmc-supply = <&ldo21_reg>; > @@ -573,6 +575,14 @@ > samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; > samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>; > }; > + > + sd2_wp: sd2-wp { > + samsung,pins = "gpm5-0"; > + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; > + /* Pin is floating so pull it up to disable write-protect */ > + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>; > + samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>; > + }; > }; > > &pwm { Best regards -- Marek Szyprowski, PhD Samsung R&D Institute Poland ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH] ARM: dts: exynos: Add CD and WP pins to Odroid XU SD card 2018-09-24 10:04 ` Marek Szyprowski @ 2018-09-26 16:13 ` Krzysztof Kozlowski -1 siblings, 0 replies; 6+ messages in thread From: Krzysztof Kozlowski @ 2018-09-26 16:13 UTC (permalink / raw) To: Marek Szyprowski Cc: Kukjin Kim, devicetree, linux-arm-kernel, linux-samsung-soc, linux-kernel, Anand Moon On Mon, Sep 24, 2018 at 12:04:52PM +0200, Marek Szyprowski wrote: > Hi Krzysztof, > > On 2018-09-21 23:03, Krzysztof Kozlowski wrote: > > Defining card-detect and write-protect GPIO pins in Odroid XU SD Card > > does not change anything from functional point of view - dw-mmc driver > > was reading the state from registers. Adding cd-gpios and wp-gpios > > properties changes only internal driver behavior to access the pins > > directly. > > > > Add them to DTS only to comprehensively describe the hardware. Minor > > benefit is that write-protect pin configuration makes sure that it will > > be properly pulled up to indicate write access. > > > > This also removes debug messages: > > dwmmc_exynos 12220000.mmc: No GPIO consumer cd found > > dwmmc_exynos 12220000.mmc: No GPIO consumer wp found > > > > Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> > > --- > > arch/arm/boot/dts/exynos5410-odroidxu.dts | 12 +++++++++++- > > 1 file changed, 11 insertions(+), 1 deletion(-) > > > > diff --git a/arch/arm/boot/dts/exynos5410-odroidxu.dts b/arch/arm/boot/dts/exynos5410-odroidxu.dts > > index a2046f5f998c..dae360f29a47 100644 > > --- a/arch/arm/boot/dts/exynos5410-odroidxu.dts > > +++ b/arch/arm/boot/dts/exynos5410-odroidxu.dts > > @@ -525,12 +525,14 @@ > > > > &mmc_2 { > > status = "okay"; > > + wp-gpios = <&gpm5 0 GPIO_ACTIVE_LOW>; > > + cd-gpios = <&gpc2 2 GPIO_ACTIVE_LOW>; > > card-detect-delay = <200>; > > samsung,dw-mshc-ciu-div = <3>; > > samsung,dw-mshc-sdr-timing = <0 4>; > > samsung,dw-mshc-ddr-timing = <0 2>; > > pinctrl-names = "default"; > > - pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus1 &sd2_bus4>; > > + pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus1 &sd2_bus4 &sd2_wp>; > > IMHO there is no point adding cd-gpios property if CD line is already > assigned to this device via respective pin ctrl entry (as special function). > > Handling of WP line is even more controversial imho. Ideally the drivers > or mmc core should check somehow if WP line is available or not and act > respectively. WP line is not available on uSD card connector so there is > no point describing it. Thanks for comments. In that case I'll add only the pin configuration to be sure that pin stays pulled up. Best regards, Krzysztof > > > bus-width = <4>; > > cap-sd-highspeed; > > vmmc-supply = <&ldo21_reg>; > > @@ -573,6 +575,14 @@ > > samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; > > samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>; > > }; > > + > > + sd2_wp: sd2-wp { > > + samsung,pins = "gpm5-0"; > > + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; > > + /* Pin is floating so pull it up to disable write-protect */ > > + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>; > > + samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>; > > + }; > > }; > > > > &pwm { > > Best regards > -- > Marek Szyprowski, PhD > Samsung R&D Institute Poland > ^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH] ARM: dts: exynos: Add CD and WP pins to Odroid XU SD card @ 2018-09-26 16:13 ` Krzysztof Kozlowski 0 siblings, 0 replies; 6+ messages in thread From: Krzysztof Kozlowski @ 2018-09-26 16:13 UTC (permalink / raw) To: linux-arm-kernel On Mon, Sep 24, 2018 at 12:04:52PM +0200, Marek Szyprowski wrote: > Hi Krzysztof, > > On 2018-09-21 23:03, Krzysztof Kozlowski wrote: > > Defining card-detect and write-protect GPIO pins in Odroid XU SD Card > > does not change anything from functional point of view - dw-mmc driver > > was reading the state from registers. Adding cd-gpios and wp-gpios > > properties changes only internal driver behavior to access the pins > > directly. > > > > Add them to DTS only to comprehensively describe the hardware. Minor > > benefit is that write-protect pin configuration makes sure that it will > > be properly pulled up to indicate write access. > > > > This also removes debug messages: > > dwmmc_exynos 12220000.mmc: No GPIO consumer cd found > > dwmmc_exynos 12220000.mmc: No GPIO consumer wp found > > > > Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> > > --- > > arch/arm/boot/dts/exynos5410-odroidxu.dts | 12 +++++++++++- > > 1 file changed, 11 insertions(+), 1 deletion(-) > > > > diff --git a/arch/arm/boot/dts/exynos5410-odroidxu.dts b/arch/arm/boot/dts/exynos5410-odroidxu.dts > > index a2046f5f998c..dae360f29a47 100644 > > --- a/arch/arm/boot/dts/exynos5410-odroidxu.dts > > +++ b/arch/arm/boot/dts/exynos5410-odroidxu.dts > > @@ -525,12 +525,14 @@ > > > > &mmc_2 { > > status = "okay"; > > + wp-gpios = <&gpm5 0 GPIO_ACTIVE_LOW>; > > + cd-gpios = <&gpc2 2 GPIO_ACTIVE_LOW>; > > card-detect-delay = <200>; > > samsung,dw-mshc-ciu-div = <3>; > > samsung,dw-mshc-sdr-timing = <0 4>; > > samsung,dw-mshc-ddr-timing = <0 2>; > > pinctrl-names = "default"; > > - pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus1 &sd2_bus4>; > > + pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus1 &sd2_bus4 &sd2_wp>; > > IMHO there is no point adding cd-gpios property if CD line is already > assigned to this device via respective pin ctrl entry (as special function). > > Handling of WP line is even more controversial imho. Ideally the drivers > or mmc core should check somehow if WP line is available or not and act > respectively. WP line is not available on uSD card connector so there is > no point describing it. Thanks for comments. In that case I'll add only the pin configuration to be sure that pin stays pulled up. Best regards, Krzysztof > > > bus-width = <4>; > > cap-sd-highspeed; > > vmmc-supply = <&ldo21_reg>; > > @@ -573,6 +575,14 @@ > > samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; > > samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>; > > }; > > + > > + sd2_wp: sd2-wp { > > + samsung,pins = "gpm5-0"; > > + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; > > + /* Pin is floating so pull it up to disable write-protect */ > > + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>; > > + samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>; > > + }; > > }; > > > > &pwm { > > Best regards > -- > Marek Szyprowski, PhD > Samsung R&D Institute Poland > ^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2018-09-26 16:13 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <CGME20180921210332epcas3p423aaeeb84ec3d8a44c5a898949f992e8@epcas3p4.samsung.com>
2018-09-21 21:03 ` [PATCH] ARM: dts: exynos: Add CD and WP pins to Odroid XU SD card Krzysztof Kozlowski
2018-09-21 21:03 ` Krzysztof Kozlowski
2018-09-24 10:04 ` Marek Szyprowski
2018-09-24 10:04 ` Marek Szyprowski
2018-09-26 16:13 ` Krzysztof Kozlowski
2018-09-26 16:13 ` Krzysztof Kozlowski
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.