Re: [PATCH v3 1/8] dt-bindings: mfd: document stpmic1

[Rob Herring <robh@kernel.org>]

On Mon, Oct 08, 2018 at 04:29:39PM +0000, Pascal PAILLET-LME wrote:
> From: pascal paillet <p.paillet@st.com>
> 
> stpmic1 is a pmic from STMicroelectronics. The STPMIC1 integrates 10
> regulators ,3 switches, a watchdog and an input for a power on key.

regulators, 3 switches, ...

> 
> Signed-off-by: pascal paillet <p.paillet@st.com>
> ---
> changes in v3:
> * Replace st,onkey-long-press-seconds by power-off-time-sec.
> * Replace interrupts-extended by  interrupts.
> * Remove wakeup interrupt.
> * Cosmetics.
> 
>  .../devicetree/bindings/mfd/st,stpmic1.txt         | 133 +++++++++++++++++++++
>  include/dt-bindings/mfd/st,stpmic1.h               |  46 +++++++
>  2 files changed, 179 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/mfd/st,stpmic1.txt
>  create mode 100644 include/dt-bindings/mfd/st,stpmic1.h

A few nits, otherwise:

Reviewed-by: Rob Herring <robh@kernel.org>

> 
> diff --git a/Documentation/devicetree/bindings/mfd/st,stpmic1.txt b/Documentation/devicetree/bindings/mfd/st,stpmic1.txt
> new file mode 100644
> index 0000000..989bd58
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mfd/st,stpmic1.txt
> @@ -0,0 +1,133 @@
> +* STMicroelectronics STPMIC1 Power Management IC
> +
> +Required parent device properties:
> +- compatible: 		"st,stpmic1"
> +- reg: 			The I2C slave address for the STPMIC1 chip.

space before tabs

> +- interrupt-parent	Phandle to the parent interrupt controller.

Drop this. It could be in the parent.

> +- interrupts: 		The interrupt line the device is connected to.
> +- #interrupt-cells: 	Should be 1.

more space before tabs.

> +- interrupt-controller: Describes the STPMIC1 as an interrupt
> +  controller (has its own domain). Interrupt number are the following:
> +	/* Interrupt Register 1 (0x50 for latch) */
> +	IT_SWOUT_R=0
> +	IT_SWOUT_F=1
> +	IT_VBUS_OTG_R=2
> +	IT_VBUS_OTG_F=3
> +	IT_WAKEUP_R=4
> +	IT_WAKEUP_F=5
> +	IT_PONKEY_R=6
> +	IT_PONKEY_F=7
> +	/* Interrupt Register 2 (0x51 for latch) */
> +	IT_OVP_BOOST=8
> +	IT_OCP_BOOST=9
> +	IT_OCP_SWOUT=10
> +	IT_OCP_OTG=11
> +	IT_CURLIM_BUCK4=12
> +	IT_CURLIM_BUCK3=13
> +	IT_CURLIM_BUCK2=14
> +	IT_CURLIM_BUCK1=15
> +	/* Interrupt Register 3 (0x52 for latch) */
> +	IT_SHORT_SWOUT=16
> +	IT_SHORT_SWOTG=17
> +	IT_CURLIM_LDO6=18
> +	IT_CURLIM_LDO5=19
> +	IT_CURLIM_LDO4=20
> +	IT_CURLIM_LDO3=21
> +	IT_CURLIM_LDO2=22
> +	IT_CURLIM_LDO1=23
> +	/* Interrupt Register 3 (0x52 for latch) */
> +	IT_SWIN_R=24
> +	IT_SWIN_F=25
> +	IT_RESERVED_1=26
> +	IT_RESERVED_2=27
> +	IT_VINLOW_R=28
> +	IT_VINLOW_F=29
> +	IT_TWARN_R=30
> +	IT_TWARN_F=31
> +
> +Optional parent device properties:
> +- st,main-control-register:
> +	-bit 1: Power cycling will be performed on turn OFF condition
> +	-bit 2: PWRCTRL is functional
> +	-bit 3: PWRCTRL active high
> +- st,pads-pull-register:
> +	-bit 1: WAKEUP pull down is not active
> +	-bit 2: PWRCTRL pull up is active
> +	-bit 3: PWRCTRL pull down is active
> +	-bit 4: WAKEUP detector is disabled
> +- st,vin-control-register:
> +	-bit 0: VINLOW monitoring is enabled
> +	-bit [1...3]: VINLOW rising threshold
> +		000 VINOK_f + 50mV
> +		001 VINOK_f + 100mV
> +		010 VINOK_f + 150mV
> +		011 VINOK_f + 200mV
> +		100 VINOK_f + 250mV
> +		101 VINOK_f + 300mV
> +		110 VINOK_f + 350mV
> +		111 VINOK_f + 400mV
> +	-bit [4...5]: VINLOW hyst
> +		00 100mV
> +		01 200mV
> +		10 300mV
> +		11 400mV
> +	-bit 6: SW_OUT detector is disabled
> +	-bit 7: SW_IN detector is enabled.
> +- st,usb-control-register:
> +	-bit 3: SW_OUT current limit
> +		0: 600mA
> +		1: 1.1A
> +	-bit 4: VBUS_OTG discharge is enabled
> +	-bit 5: SW_OUT discharge is enabled
> +	-bit 6: VBUS_OTG detection is enabled
> +	-bit 7: BOOST_OVP is disabled
> +
> +STPMIC1 consists in a varied group of sub-devices.
> +Each sub-device binding is be described in own documentation file.
> +
> +Device			 Description
> +------			------------
> +st,stpmic1-onkey	: Power on key, see ../input/st,stpmic1-onkey.txt
> +st,stpmic1-regulators	: Regulators, see ../regulator/st,stpmic1-regulator.txt
> +st,stpmic1-wdt		: Watchdog, see ../watchdog/st,stpmic1-wdt.txt
> +
> +Example:
> +
> +pmic: pmic1@33 {

pmic@33

> +	compatible = "st,stpmic1";
> +	reg = <0x33>;
> +	interrupt-parent = <&gpioa>;
> +	interrupts = <0 2>;
> +	st,main-control-register=<0x0c>;
> +	interrupt-controller;
> +	#interrupt-cells = <2>;
> +
> +	onkey {
> +		compatible = "st,stpmic1-onkey";
> +		interrupt-parent = <&pmic>;

Not needed because the parent is the interrupt controller.

> +		interrupts = <IT_PONKEY_F 0>,<IT_PONKEY_R 1>;
> +		interrupt-names = "onkey-falling", "onkey-rising";
> +		power-off-time-sec = <10>;
> +	};
> +
> +	watchdog {
> +		compatible = "st,stpmic1-wdt";
> +	};
> +
> +	regulators {
> +		compatible = "st,stpmic1-regulators";
> +
> +		vdd_core: buck1 {
> +			regulator-name = "vdd_core";
> +			regulator-boot-on;
> +			regulator-min-microvolt = <700000>;
> +			regulator-max-microvolt = <1200000>;
> +		};
> +		vdd: buck3 {
> +			regulator-name = "vdd";
> +			regulator-min-microvolt = <3300000>;
> +			regulator-max-microvolt = <3300000>;
> +			regulator-boot-on;
> +			regulator-pull-down;
> +		};
> +	};
> diff --git a/include/dt-bindings/mfd/st,stpmic1.h b/include/dt-bindings/mfd/st,stpmic1.h
> new file mode 100644
> index 0000000..b2d6c83
> --- /dev/null
> +++ b/include/dt-bindings/mfd/st,stpmic1.h
> @@ -0,0 +1,46 @@
> +/* SPDX-License-Identifier: GPL-2.0 */
> +/*
> + * Copyright (C) STMicroelectronics 2018 - All Rights Reserved
> + * Author: Philippe Peurichard <philippe.peurichard@st.com>,
> + * Pascal Paillet <p.paillet@st.com> for STMicroelectronics.
> + */
> +
> +#ifndef __DT_BINDINGS_STPMIC1_H__
> +#define __DT_BINDINGS_STPMIC1_H__
> +
> +/* IRQ definitions */
> +#define IT_PONKEY_F	0
> +#define IT_PONKEY_R	1
> +#define IT_WAKEUP_F	2
> +#define IT_WAKEUP_R	3
> +#define IT_VBUS_OTG_F	4
> +#define IT_VBUS_OTG_R	5
> +#define IT_SWOUT_F	6
> +#define IT_SWOUT_R	7
> +
> +#define IT_CURLIM_BUCK1	8
> +#define IT_CURLIM_BUCK2	9
> +#define IT_CURLIM_BUCK3	10
> +#define IT_CURLIM_BUCK4	11
> +#define IT_OCP_OTG	12
> +#define IT_OCP_SWOUT	13
> +#define IT_OCP_BOOST	14
> +#define IT_OVP_BOOST	15
> +
> +#define IT_CURLIM_LDO1	16
> +#define IT_CURLIM_LDO2	17
> +#define IT_CURLIM_LDO3	18
> +#define IT_CURLIM_LDO4	19
> +#define IT_CURLIM_LDO5	20
> +#define IT_CURLIM_LDO6	21
> +#define IT_SHORT_SWOTG	22
> +#define IT_SHORT_SWOUT	23
> +
> +#define IT_TWARN_F	24
> +#define IT_TWARN_R	25
> +#define IT_VINLOW_F	26
> +#define IT_VINLOW_R	27
> +#define IT_SWIN_F	30
> +#define IT_SWIN_R	31
> +
> +#endif /* __DT_BINDINGS_STPMIC1_H__ */
> -- 
> 1.9.1