From: Rodrigo Vivi <rodrigo.vivi@intel.com>
To: "José Roberto de Souza" <jose.souza@intel.com>
Cc: intel-gfx@lists.freedesktop.org,
Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Subject: Re: [PATCH v3 02/10] drm/i915/psr: Always wait for idle state when disabling PSR
Date: Fri, 26 Oct 2018 09:45:17 -0700 [thread overview]
Message-ID: <20181026164517.GD2232@intel.com> (raw)
In-Reply-To: <20181026011737.23684-2-jose.souza@intel.com>
On Thu, Oct 25, 2018 at 06:17:29PM -0700, José Roberto de Souza wrote:
> It should always wait for idle state when disabling PSR because PSR
> could be inactive due a call to intel_psr_exit() and while PSR is
> still being disabled asynchronously userspace could change the
> modeset causing a call to psr_disable() that will not wait for PSR
> idle and then PSR will be enabled again while PSR is still not idle.
>
> v2: rebased on top of the patch reusing psr_exit()
>
> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
> Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
> Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
> Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
> ---
> drivers/gpu/drm/i915/intel_psr.c | 41 ++++++++++++++------------------
> 1 file changed, 18 insertions(+), 23 deletions(-)
>
> diff --git a/drivers/gpu/drm/i915/intel_psr.c b/drivers/gpu/drm/i915/intel_psr.c
> index f698b3f45c6d..4c226b78c3fc 100644
> --- a/drivers/gpu/drm/i915/intel_psr.c
> +++ b/drivers/gpu/drm/i915/intel_psr.c
> @@ -661,8 +661,12 @@ static void intel_psr_exit(struct drm_i915_private *dev_priv)
> {
> u32 val;
>
> - if (!dev_priv->psr.active)
> + if (!dev_priv->psr.active) {
> + if (INTEL_GEN(dev_priv) >= 9)
This should be PSR2 check instead of platform no?!
> + WARN_ON(I915_READ(EDP_PSR2_CTL) & EDP_PSR2_ENABLE);
> + WARN_ON(I915_READ(EDP_PSR_CTL) & EDP_PSR_ENABLE);
> return;
> + }
>
> if (dev_priv->psr.psr2_enabled) {
> val = I915_READ(EDP_PSR2_CTL);
> @@ -680,32 +684,23 @@ static void
> intel_psr_disable_source(struct intel_dp *intel_dp)
> {
> struct drm_i915_private *dev_priv = dp_to_i915(intel_dp);
> + i915_reg_t psr_status;
> + u32 psr_status_mask;
>
> - if (dev_priv->psr.active) {
> - i915_reg_t psr_status;
> - u32 psr_status_mask;
> -
> - intel_psr_exit(dev_priv);
> + intel_psr_exit(dev_priv);
>
> - if (dev_priv->psr.psr2_enabled) {
> - psr_status = EDP_PSR2_STATUS;
> - psr_status_mask = EDP_PSR2_STATUS_STATE_MASK;
> - } else {
> - psr_status = EDP_PSR_STATUS;
> - psr_status_mask = EDP_PSR_STATUS_STATE_MASK;
> - }
> -
> - /* Wait till PSR is idle */
> - if (intel_wait_for_register(dev_priv,
> - psr_status, psr_status_mask, 0,
> - 2000))
> - DRM_ERROR("Timed out waiting for PSR Idle State\n");
> + if (dev_priv->psr.psr2_enabled) {
> + psr_status = EDP_PSR2_STATUS;
> + psr_status_mask = EDP_PSR2_STATUS_STATE_MASK;
> } else {
> - if (dev_priv->psr.psr2_enabled)
> - WARN_ON(I915_READ(EDP_PSR2_CTL) & EDP_PSR2_ENABLE);
> - else
> - WARN_ON(I915_READ(EDP_PSR_CTL) & EDP_PSR_ENABLE);
> + psr_status = EDP_PSR_STATUS;
> + psr_status_mask = EDP_PSR_STATUS_STATE_MASK;
> }
> +
> + /* Wait till PSR is idle */
> + if (intel_wait_for_register(dev_priv, psr_status, psr_status_mask, 0,
> + 2000))
> + DRM_ERROR("Timed out waiting PSR idle state\n");
> }
>
> static void intel_psr_disable_locked(struct intel_dp *intel_dp)
> --
> 2.19.1
>
> _______________________________________________
> Intel-gfx mailing list
> Intel-gfx@lists.freedesktop.org
> https://lists.freedesktop.org/mailman/listinfo/intel-gfx
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
next prev parent reply other threads:[~2018-10-26 16:45 UTC|newest]
Thread overview: 23+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-10-26 1:17 [PATCH v3 01/10] drm/i915/psr: Use intel_psr_exit() in intel_psr_disable_source() José Roberto de Souza
2018-10-26 1:17 ` [PATCH v3 02/10] drm/i915/psr: Always wait for idle state when disabling PSR José Roberto de Souza
2018-10-26 16:45 ` Rodrigo Vivi [this message]
2018-10-26 17:10 ` Souza, Jose
2018-10-26 1:17 ` [PATCH v3 03/10] drm/i915/psr: Move intel_psr_disable_source() code to intel_psr_disable_locked() José Roberto de Souza
2018-10-26 1:17 ` [PATCH v3 04/10] drm/i915: Avoid a full port detection in the first eDP short pulse José Roberto de Souza
2018-10-26 1:17 ` [PATCH v3 05/10] drm/i915: Check PSR errors instead of retrain while PSR is enabled José Roberto de Souza
2018-10-26 1:17 ` [PATCH v3 06/10] drm/i915: Unmask PSR interruptions before assert IIR José Roberto de Souza
2018-10-26 17:06 ` Ville Syrjälä
2018-10-26 1:17 ` [PATCH v3 07/10] drm/i915/icl: Reset PSR interruptions José Roberto de Souza
2018-10-26 17:13 ` Ville Syrjälä
2018-10-26 1:17 ` [PATCH v3 08/10] drm/i915: Disable PSR when a PSR aux error happen José Roberto de Souza
2018-10-26 1:17 ` [PATCH v3 09/10] drm/i915: Keep PSR disabled after a driver reload after a PSR error José Roberto de Souza
2018-10-26 17:53 ` Souza, Jose
2018-10-26 18:01 ` Ville Syrjälä
2018-10-26 19:34 ` Souza, Jose
2018-10-29 11:18 ` Ville Syrjälä
2018-10-31 23:45 ` Dhinakaran Pandiyan
2018-11-06 0:00 ` Souza, Jose
2018-10-26 1:17 ` [PATCH v3 10/10] drm/i915: Do not enable PSR in the next modeset after a error José Roberto de Souza
2018-10-26 1:26 ` ✗ Fi.CI.CHECKPATCH: warning for series starting with [v3,01/10] drm/i915/psr: Use intel_psr_exit() in intel_psr_disable_source() Patchwork
2018-10-26 1:29 ` ✗ Fi.CI.SPARSE: " Patchwork
2018-10-26 1:47 ` ✗ Fi.CI.BAT: failure " Patchwork
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20181026164517.GD2232@intel.com \
--to=rodrigo.vivi@intel.com \
--cc=dhinakaran.pandiyan@intel.com \
--cc=intel-gfx@lists.freedesktop.org \
--cc=jose.souza@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.