Re: [PATCH 2/4] ARM: dts: imx7d: cl-som-imx7: WiLink8 WLAN support

From: Shawn Guo <shawnguo@kernel.org>
To: Hans Ole Hatzel <hohatzel@jusst.de>
Cc: devicetree@vger.kernel.org, Julian Scheel <jscheel@jusst.de>,
	linux-arm-kernel@lists.infradead.org, fabio.estevam@nxp.com,
	ilya@compulab.co.il, linux-imx@nxp.com
Subject: Re: [PATCH 2/4] ARM: dts: imx7d: cl-som-imx7: WiLink8 WLAN support
Date: Thu, 6 Dec 2018 11:11:36 +0800	[thread overview]
Message-ID: <20181206031134.GC3987@dragon> (raw)
In-Reply-To: <20181204110741.6943-3-hohatzel@jusst.de>

On Tue, Dec 04, 2018 at 12:07:39PM +0100, Hans Ole Hatzel wrote:
> Add support for WiLink8 module which is connected via USDHC 2.
> 
> Signed-off-by: Hans Ole Hatzel <hohatzel@jusst.de>
> Signed-off-by: Julian Scheel <jscheel@jusst.de>
> ---
>  arch/arm/boot/dts/imx7d-cl-som-imx7.dts | 64 +++++++++++++++++++++++++
>  1 file changed, 64 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/imx7d-cl-som-imx7.dts b/arch/arm/boot/dts/imx7d-cl-som-imx7.dts
> index 11bd713b540f..e77e0cc7de39 100644
> --- a/arch/arm/boot/dts/imx7d-cl-som-imx7.dts
> +++ b/arch/arm/boot/dts/imx7d-cl-som-imx7.dts
> @@ -30,6 +30,28 @@
>  		gpio = <&gpio1 5 GPIO_ACTIVE_HIGH>;
>  		enable-active-high;
>  	};
> +
> +	rf_pwr_en_reg: regulator-rf-pwr-en {
> +		compatible = "regulator-fixed";
> +		regulator-name = "rf-pwr-en-regulator";

I think "rf-pwr-en" is good enough.

> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		gpio = <&pca9555 9 GPIO_ACTIVE_HIGH>;
> +		startup-delay-us = <70000>;
> +		enable-active-high;
> +		regulator-always-on;
> +	};
> +
> +	wlan_en_reg: regulator-wlan-en {
> +		compatible = "regulator-fixed";
> +		regulator-name = "wlan-en-regulator";

"wlan-en"

> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		gpio = <&pca9555 0 GPIO_ACTIVE_HIGH>;
> +		/* WLAN card specific delay */
> +		startup-delay-us = <70000>;
> +		enable-active-high;
> +	};
>  };
>  
>  &cpu0 {
> @@ -199,6 +221,28 @@
>  	status = "okay";
>  };
>  
> +&usdhc2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_usdhc2>;
> +	cd-gpios = <>;
> +	wp-gpios = <>;

What do these mean?

> +	no-1-8-v;
> +	keep-power-in-suspend;
> +	enable-sdio-wakeup;

The property is deprecated.  Use "wakeup-source" instead.

> +	vmmc-supply = <&wlan_en_reg>;
> +	non-removable;
> +	cap-power-off-card;
> +	status = "okay";

Put 'status' at bottom of property list.

> +	#address-cells = <1>;
> +	#size-cells = <0>;

Have a newline between properties and child node.

> +	wlcore: wlcore@0 {
> +		compatible = "ti,wl1835";
> +		reg = <2>;

The 'reg' property should match unit-address in node name.

Shawn

> +		interrupt-parent = <&gpio1>;
> +		interrupts = <15 IRQ_TYPE_LEVEL_HIGH>;
> +	};
> +};
> +
>  &usdhc3 {
>  	pinctrl-names = "default";
>  	pinctrl-0 = <&pinctrl_usdhc3>;
> @@ -211,6 +255,15 @@
>  };
>  
>  &iomuxc {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_hog>;
> +
> +	pinctrl_hog: hoggrp {
> +		fsl,pins = <
> +			MX7D_PAD_GPIO1_IO15__GPIO1_IO15			0x34 /* WLAN IRQ */
> +		>;
> +	};
> +
>  	pinctrl_enet1: enet1grp {
>  		fsl,pins = <
>  			MX7D_PAD_SD2_CD_B__ENET1_MDIO			0x30
> @@ -261,6 +314,17 @@
>  		>;
>  	};
>  
> +	pinctrl_usdhc2: usdhc2grp {
> +		fsl,pins = <
> +			MX7D_PAD_SD2_CMD__SD2_CMD			0x59
> +			MX7D_PAD_SD2_CLK__SD2_CLK			0x19
> +			MX7D_PAD_SD2_DATA0__SD2_DATA0			0x59
> +			MX7D_PAD_SD2_DATA1__SD2_DATA1			0x59
> +			MX7D_PAD_SD2_DATA2__SD2_DATA2			0x59
> +			MX7D_PAD_SD2_DATA3__SD2_DATA3			0x59
> +		>;
> +	};
> +
>  	pinctrl_usdhc3: usdhc3grp {
>  		fsl,pins = <
>  			MX7D_PAD_SD3_CMD__SD3_CMD		0x59
> -- 
> 2.19.2
> 
> 
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel