[PATCH AUTOSEL 4.9 01/35] pinctrl: meson: fix pull enable register calculation

[PATCH AUTOSEL 4.9 01/35] pinctrl: meson: fix pull enable register calculation

[Sasha Levin]

From: Jerome Brunet <jbrunet@baylibre.com>

[ Upstream commit 614b1868a125a0ba24be08f3a7fa832ddcde6bca ]

We just changed the code so we apply bias disable on the correct
register but forgot to align the register calculation. The result
is that we apply the change on the correct register, but possibly
at the incorrect offset/bit

This went undetected because offsets tends to be the same between
REG_PULL and REG_PULLEN for a given pin the EE controller. This
is not true for the AO controller.

Fixes: e39f9dd8206a ("pinctrl: meson: fix pinconf bias disable")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/pinctrl/meson/pinctrl-meson.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/pinctrl/meson/pinctrl-meson.c b/drivers/pinctrl/meson/pinctrl-meson.c
index df61a71420b1..8e73641bd823 100644
--- a/drivers/pinctrl/meson/pinctrl-meson.c
+++ b/drivers/pinctrl/meson/pinctrl-meson.c
@@ -274,7 +274,8 @@ static int meson_pinconf_set(struct pinctrl_dev *pcdev, unsigned int pin,
 		case PIN_CONFIG_BIAS_DISABLE:
 			dev_dbg(pc->dev, "pin %u: disable bias\n", pin);
 
-			meson_calc_reg_and_bit(bank, pin, REG_PULL, &reg, &bit);
+			meson_calc_reg_and_bit(bank, pin, REG_PULLEN, &reg,
+					       &bit);
 			ret = regmap_update_bits(pc->reg_pullen, reg,
 						 BIT(bit), 0);
 			if (ret)
-- 
2.19.1


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

[PATCH AUTOSEL 4.9 01/35] pinctrl: meson: fix pull enable register calculation

[Sasha Levin]

From: Jerome Brunet <jbrunet@baylibre.com>

[ Upstream commit 614b1868a125a0ba24be08f3a7fa832ddcde6bca ]

We just changed the code so we apply bias disable on the correct
register but forgot to align the register calculation. The result
is that we apply the change on the correct register, but possibly
at the incorrect offset/bit

This went undetected because offsets tends to be the same between
REG_PULL and REG_PULLEN for a given pin the EE controller. This
is not true for the AO controller.

Fixes: e39f9dd8206a ("pinctrl: meson: fix pinconf bias disable")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/pinctrl/meson/pinctrl-meson.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/pinctrl/meson/pinctrl-meson.c b/drivers/pinctrl/meson/pinctrl-meson.c
index df61a71420b1..8e73641bd823 100644
--- a/drivers/pinctrl/meson/pinctrl-meson.c
+++ b/drivers/pinctrl/meson/pinctrl-meson.c
@@ -274,7 +274,8 @@ static int meson_pinconf_set(struct pinctrl_dev *pcdev, unsigned int pin,
 		case PIN_CONFIG_BIAS_DISABLE:
 			dev_dbg(pc->dev, "pin %u: disable bias\n", pin);
 
-			meson_calc_reg_and_bit(bank, pin, REG_PULL, &reg, &bit);
+			meson_calc_reg_and_bit(bank, pin, REG_PULLEN, &reg,
+					       &bit);
 			ret = regmap_update_bits(pc->reg_pullen, reg,
 						 BIT(bit), 0);
 			if (ret)
-- 
2.19.1

[PATCH AUTOSEL 4.9 02/35] powerpc: Fix COFF zImage booting on old powermacs

[Sasha Levin]

From: Paul Mackerras <paulus@ozlabs.org>

[ Upstream commit 5564597d51c8ff5b88d95c76255e18b13b760879 ]

Commit 6975a783d7b4 ("powerpc/boot: Allow building the zImage wrapper
as a relocatable ET_DYN", 2011-04-12) changed the procedure descriptor
at the start of crt0.S to have a hard-coded start address of 0x500000
rather than a reference to _zimage_start, presumably because having
a reference to a symbol introduced a relocation which is awkward to
handle in a position-independent executable.  Unfortunately, what is
at 0x500000 in the COFF image is not the first instruction, but the
procedure descriptor itself, that is, a word containing 0x500000,
which is not a valid instruction.  Hence, booting a COFF zImage
results in a "DEFAULT CATCH!, code=FFF00700" message from Open
Firmware.

This fixes the problem by (a) putting the procedure descriptor in the
data section and (b) adding a branch to _zimage_start as the first
instruction in the program.

Fixes: 6975a783d7b4 ("powerpc/boot: Allow building the zImage wrapper as a relocatable ET_DYN")
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/powerpc/boot/crt0.S | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/arch/powerpc/boot/crt0.S b/arch/powerpc/boot/crt0.S
index 5c2199857aa8..a3550e8f1a77 100644
--- a/arch/powerpc/boot/crt0.S
+++ b/arch/powerpc/boot/crt0.S
@@ -15,7 +15,7 @@
 RELA = 7
 RELACOUNT = 0x6ffffff9
 
-	.text
+	.data
 	/* A procedure descriptor used when booting this as a COFF file.
 	 * When making COFF, this comes first in the link and we're
 	 * linked at 0x500000.
@@ -23,6 +23,8 @@ RELACOUNT = 0x6ffffff9
 	.globl	_zimage_start_opd
 _zimage_start_opd:
 	.long	0x500000, 0, 0, 0
+	.text
+	b	_zimage_start
 
 #ifdef __powerpc64__
 .balign 8
-- 
2.19.1

[PATCH AUTOSEL 4.9 04/35] ARM: dts: imx7d-nitrogen7: Fix the description of the Wifi clock

[Sasha Levin]

From: Fabio Estevam <festevam@gmail.com>

[ Upstream commit f15096f12a4e9340168df5fdd9201aa8ed60d59e ]

According to bindings/regulator/fixed-regulator.txt the 'clocks' and
'clock-names' properties are not valid ones.

In order to turn on the Wifi clock the correct location for describing
the CLKO2 clock is via a mmc-pwrseq handle, so do it accordingly.

Fixes: 56354959cfec ("ARM: dts: imx: add Boundary Devices Nitrogen7 board")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx7d-nitrogen7.dts | 9 +++++++--
 1 file changed, 7 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/imx7d-nitrogen7.dts b/arch/arm/boot/dts/imx7d-nitrogen7.dts
index ce08f180f213..080a4ea841c9 100644
--- a/arch/arm/boot/dts/imx7d-nitrogen7.dts
+++ b/arch/arm/boot/dts/imx7d-nitrogen7.dts
@@ -117,13 +117,17 @@
 		compatible = "regulator-fixed";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
-		clocks = <&clks IMX7D_CLKO2_ROOT_DIV>;
-		clock-names = "slow";
 		regulator-name = "reg_wlan";
 		startup-delay-us = <70000>;
 		gpio = <&gpio4 21 GPIO_ACTIVE_HIGH>;
 		enable-active-high;
 	};
+
+	usdhc2_pwrseq: usdhc2_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		clocks = <&clks IMX7D_CLKO2_ROOT_DIV>;
+		clock-names = "ext_clock";
+	};
 };
 
 &adc1 {
@@ -430,6 +434,7 @@
 	bus-width = <4>;
 	non-removable;
 	vmmc-supply = <&reg_wlan>;
+	mmc-pwrseq = <&usdhc2_pwrseq>;
 	cap-power-off-card;
 	keep-power-in-suspend;
 	status = "okay";
-- 
2.19.1

[PATCH AUTOSEL 4.9 05/35] Input: restore EV_ABS ABS_RESERVED

[Sasha Levin]

From: Peter Hutterer <peter.hutterer@who-t.net>

[ Upstream commit c201e3808e0e4be9b98d192802085a9f491bd80c ]

ABS_RESERVED was added in d9ca1c990a7 and accidentally removed as part of
ffe0e7cf290f5c9 when the high-resolution scrolling code was removed.

Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Martin Kepplinger <martin.kepplinger@ginzinger.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 include/uapi/linux/input-event-codes.h | 9 +++++++++
 1 file changed, 9 insertions(+)

diff --git a/include/uapi/linux/input-event-codes.h b/include/uapi/linux/input-event-codes.h
index 3af60ee69053..b584868e1b26 100644
--- a/include/uapi/linux/input-event-codes.h
+++ b/include/uapi/linux/input-event-codes.h
@@ -739,6 +739,15 @@
 
 #define ABS_MISC		0x28
 
+/*
+ * 0x2e is reserved and should not be used in input drivers.
+ * It was used by HID as ABS_MISC+6 and userspace needs to detect if
+ * the next ABS_* event is correct or is just ABS_MISC + n.
+ * We define here ABS_RESERVED so userspace can rely on it and detect
+ * the situation described above.
+ */
+#define ABS_RESERVED		0x2e
+
 #define ABS_MT_SLOT		0x2f	/* MT slot being modified */
 #define ABS_MT_TOUCH_MAJOR	0x30	/* Major axis of touching ellipse */
 #define ABS_MT_TOUCH_MINOR	0x31	/* Minor axis (omit if circular) */
-- 
2.19.1

[PATCH AUTOSEL 4.9 08/35] netfilter: seqadj: re-load tcp header pointer after possible head reallocation

[Sasha Levin]

From: Florian Westphal <fw@strlen.de>

[ Upstream commit 530aad77010b81526586dfc09130ec875cd084e4 ]

When adjusting sack block sequence numbers, skb_make_writable() gets
called to make sure tcp options are all in the linear area, and buffer
is not shared.

This can cause tcp header pointer to get reallocated, so we must
reaload it to avoid memory corruption.

This bug pre-dates git history.

Reported-by: Neel Mehta <nmehta@google.com>
Reported-by: Shane Huntley <shuntley@google.com>
Reported-by: Heather Adkins <argv@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/netfilter/nf_conntrack_seqadj.c | 7 ++++---
 1 file changed, 4 insertions(+), 3 deletions(-)

diff --git a/net/netfilter/nf_conntrack_seqadj.c b/net/netfilter/nf_conntrack_seqadj.c
index ef7063eced7c..dad08b9eaf62 100644
--- a/net/netfilter/nf_conntrack_seqadj.c
+++ b/net/netfilter/nf_conntrack_seqadj.c
@@ -115,12 +115,12 @@ static void nf_ct_sack_block_adjust(struct sk_buff *skb,
 /* TCP SACK sequence number adjustment */
 static unsigned int nf_ct_sack_adjust(struct sk_buff *skb,
 				      unsigned int protoff,
-				      struct tcphdr *tcph,
 				      struct nf_conn *ct,
 				      enum ip_conntrack_info ctinfo)
 {
-	unsigned int dir, optoff, optend;
+	struct tcphdr *tcph = (void *)skb->data + protoff;
 	struct nf_conn_seqadj *seqadj = nfct_seqadj(ct);
+	unsigned int dir, optoff, optend;
 
 	optoff = protoff + sizeof(struct tcphdr);
 	optend = protoff + tcph->doff * 4;
@@ -128,6 +128,7 @@ static unsigned int nf_ct_sack_adjust(struct sk_buff *skb,
 	if (!skb_make_writable(skb, optend))
 		return 0;
 
+	tcph = (void *)skb->data + protoff;
 	dir = CTINFO2DIR(ctinfo);
 
 	while (optoff < optend) {
@@ -207,7 +208,7 @@ int nf_ct_seq_adjust(struct sk_buff *skb,
 		 ntohl(newack));
 	tcph->ack_seq = newack;
 
-	res = nf_ct_sack_adjust(skb, protoff, tcph, ct, ctinfo);
+	res = nf_ct_sack_adjust(skb, protoff, ct, ctinfo);
 out:
 	spin_unlock_bh(&ct->lock);
 
-- 
2.19.1

[PATCH AUTOSEL 4.9 09/35] scsi: bnx2fc: Fix NULL dereference in error handling

[Sasha Levin]

From: Dan Carpenter <dan.carpenter@oracle.com>

[ Upstream commit 9ae4f8420ed7be4b13c96600e3568c144d101a23 ]

If "interface" is NULL then we can't release it and trying to will only
lead to an Oops.

Fixes: aea71a024914 ("[SCSI] bnx2fc: Introduce interface structure for each vlan interface")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/scsi/bnx2fc/bnx2fc_fcoe.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/scsi/bnx2fc/bnx2fc_fcoe.c b/drivers/scsi/bnx2fc/bnx2fc_fcoe.c
index bee7d37367ca..68cc332bd6cb 100644
--- a/drivers/scsi/bnx2fc/bnx2fc_fcoe.c
+++ b/drivers/scsi/bnx2fc/bnx2fc_fcoe.c
@@ -2331,7 +2331,7 @@ static int _bnx2fc_create(struct net_device *netdev,
 	if (!interface) {
 		printk(KERN_ERR PFX "bnx2fc_interface_create failed\n");
 		rc = -ENOMEM;
-		goto ifput_err;
+		goto netdev_err;
 	}
 
 	if (netdev->priv_flags & IFF_802_1Q_VLAN) {
-- 
2.19.1

[PATCH AUTOSEL 4.9 10/35] Input: omap-keypad - fix idle configuration to not block SoC idle states

[Sasha Levin]

From: Tony Lindgren <tony@atomide.com>

[ Upstream commit e2ca26ec4f01486661b55b03597c13e2b9c18b73 ]

With PM enabled, I noticed that pressing a key on the droid4 keyboard will
block deeper idle states for the SoC. Let's fix this by using IRQF_ONESHOT
and stop constantly toggling the device OMAP4_KBD_IRQENABLE register as
suggested by Dmitry Torokhov <dmitry.torokhov@gmail.com>.

>From the hardware point of view, looks like we need to manage the registers
for OMAP4_KBD_IRQENABLE and OMAP4_KBD_WAKEUPENABLE together to avoid
blocking deeper SoC idle states. And with toggling of OMAP4_KBD_IRQENABLE
register now gone with IRQF_ONESHOT, also the SoC idle state problem is
gone during runtime. We still also need to clear OMAP4_KBD_WAKEUPENABLE in
omap4_keypad_close() though to pair it with omap4_keypad_open() to prevent
blocking deeper SoC idle states after rmmod omap4-keypad.

Reported-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/input/keyboard/omap4-keypad.c | 16 ++++------------
 1 file changed, 4 insertions(+), 12 deletions(-)

diff --git a/drivers/input/keyboard/omap4-keypad.c b/drivers/input/keyboard/omap4-keypad.c
index f78c464899db..3d2c60c8de83 100644
--- a/drivers/input/keyboard/omap4-keypad.c
+++ b/drivers/input/keyboard/omap4-keypad.c
@@ -126,12 +126,8 @@ static irqreturn_t omap4_keypad_irq_handler(int irq, void *dev_id)
 {
 	struct omap4_keypad *keypad_data = dev_id;
 
-	if (kbd_read_irqreg(keypad_data, OMAP4_KBD_IRQSTATUS)) {
-		/* Disable interrupts */
-		kbd_write_irqreg(keypad_data, OMAP4_KBD_IRQENABLE,
-				 OMAP4_VAL_IRQDISABLE);
+	if (kbd_read_irqreg(keypad_data, OMAP4_KBD_IRQSTATUS))
 		return IRQ_WAKE_THREAD;
-	}
 
 	return IRQ_NONE;
 }
@@ -173,11 +169,6 @@ static irqreturn_t omap4_keypad_irq_thread_fn(int irq, void *dev_id)
 	kbd_write_irqreg(keypad_data, OMAP4_KBD_IRQSTATUS,
 			 kbd_read_irqreg(keypad_data, OMAP4_KBD_IRQSTATUS));
 
-	/* enable interrupts */
-	kbd_write_irqreg(keypad_data, OMAP4_KBD_IRQENABLE,
-		OMAP4_DEF_IRQENABLE_EVENTEN |
-				OMAP4_DEF_IRQENABLE_LONGKEY);
-
 	return IRQ_HANDLED;
 }
 
@@ -214,9 +205,10 @@ static void omap4_keypad_close(struct input_dev *input)
 
 	disable_irq(keypad_data->irq);
 
-	/* Disable interrupts */
+	/* Disable interrupts and wake-up events */
 	kbd_write_irqreg(keypad_data, OMAP4_KBD_IRQENABLE,
 			 OMAP4_VAL_IRQDISABLE);
+	kbd_writel(keypad_data, OMAP4_KBD_WAKEUPENABLE, 0);
 
 	/* clear pending interrupts */
 	kbd_write_irqreg(keypad_data, OMAP4_KBD_IRQSTATUS,
@@ -364,7 +356,7 @@ static int omap4_keypad_probe(struct platform_device *pdev)
 	}
 
 	error = request_threaded_irq(keypad_data->irq, omap4_keypad_irq_handler,
-				     omap4_keypad_irq_thread_fn, 0,
+				     omap4_keypad_irq_thread_fn, IRQF_ONESHOT,
 				     "omap4-keypad", keypad_data);
 	if (error) {
 		dev_err(&pdev->dev, "failed to register interrupt\n");
-- 
2.19.1

[PATCH AUTOSEL 4.9 12/35] netfilter: ipset: do not call ipset_nest_end after nla_nest_cancel

[Sasha Levin]

From: Pan Bian <bianpan2016@163.com>

[ Upstream commit 708abf74dd87f8640871b814faa195fb5970b0e3 ]

In the error handling block, nla_nest_cancel(skb, atd) is called to
cancel the nest operation. But then, ipset_nest_end(skb, atd) is
unexpected called to end the nest operation. This patch calls the
ipset_nest_end only on the branch that nla_nest_cancel is not called.

Fixes: 45040978c899 ("netfilter: ipset: Fix set:list type crash when flush/dump set in parallel")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/netfilter/ipset/ip_set_list_set.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/net/netfilter/ipset/ip_set_list_set.c b/net/netfilter/ipset/ip_set_list_set.c
index a2a89e4e0a14..e82157285d34 100644
--- a/net/netfilter/ipset/ip_set_list_set.c
+++ b/net/netfilter/ipset/ip_set_list_set.c
@@ -518,8 +518,8 @@ list_set_list(const struct ip_set *set,
 		ret = -EMSGSIZE;
 	} else {
 		cb->args[IPSET_CB_ARG0] = i;
+		ipset_nest_end(skb, atd);
 	}
-	ipset_nest_end(skb, atd);
 out:
 	rcu_read_unlock();
 	return ret;
-- 
2.19.1

[PATCH AUTOSEL 4.9 16/35] scsi: target: iscsi: cxgbit: fix csk leak

[Sasha Levin]

From: Varun Prakash <varun@chelsio.com>

[ Upstream commit 801df68d617e3cb831f531c99fa6003620e6b343 ]

csk leak can happen if a new TCP connection gets established after
cxgbit_accept_np() returns, to fix this leak free remaining csk in
cxgbit_free_np().

Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/target/iscsi/cxgbit/cxgbit_cm.c | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)

diff --git a/drivers/target/iscsi/cxgbit/cxgbit_cm.c b/drivers/target/iscsi/cxgbit/cxgbit_cm.c
index 2fb1bf1a26c5..8652475e01d0 100644
--- a/drivers/target/iscsi/cxgbit/cxgbit_cm.c
+++ b/drivers/target/iscsi/cxgbit/cxgbit_cm.c
@@ -631,8 +631,11 @@ static void cxgbit_send_halfclose(struct cxgbit_sock *csk)
 
 static void cxgbit_arp_failure_discard(void *handle, struct sk_buff *skb)
 {
+	struct cxgbit_sock *csk = handle;
+
 	pr_debug("%s cxgbit_device %p\n", __func__, handle);
 	kfree_skb(skb);
+	cxgbit_put_csk(csk);
 }
 
 static void cxgbit_abort_arp_failure(void *handle, struct sk_buff *skb)
@@ -1136,7 +1139,7 @@ cxgbit_pass_accept_rpl(struct cxgbit_sock *csk, struct cpl_pass_accept_req *req)
 	rpl5->opt0 = cpu_to_be64(opt0);
 	rpl5->opt2 = cpu_to_be32(opt2);
 	set_wr_txq(skb, CPL_PRIORITY_SETUP, csk->ctrlq_idx);
-	t4_set_arp_err_handler(skb, NULL, cxgbit_arp_failure_discard);
+	t4_set_arp_err_handler(skb, csk, cxgbit_arp_failure_discard);
 	cxgbit_l2t_send(csk->com.cdev, skb, csk->l2t);
 }
 
-- 
2.19.1

[PATCH AUTOSEL 4.9 16/35] scsi: target: iscsi: cxgbit: fix csk leak

[Sasha Levin]

From: Varun Prakash <varun@chelsio.com>

[ Upstream commit 801df68d617e3cb831f531c99fa6003620e6b343 ]

csk leak can happen if a new TCP connection gets established after
cxgbit_accept_np() returns, to fix this leak free remaining csk in
cxgbit_free_np().

Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/target/iscsi/cxgbit/cxgbit_cm.c | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)

diff --git a/drivers/target/iscsi/cxgbit/cxgbit_cm.c b/drivers/target/iscsi/cxgbit/cxgbit_cm.c
index 2fb1bf1a26c5..8652475e01d0 100644
--- a/drivers/target/iscsi/cxgbit/cxgbit_cm.c
+++ b/drivers/target/iscsi/cxgbit/cxgbit_cm.c
@@ -631,8 +631,11 @@ static void cxgbit_send_halfclose(struct cxgbit_sock *csk)
 
 static void cxgbit_arp_failure_discard(void *handle, struct sk_buff *skb)
 {
+	struct cxgbit_sock *csk = handle;
+
 	pr_debug("%s cxgbit_device %p\n", __func__, handle);
 	kfree_skb(skb);
+	cxgbit_put_csk(csk);
 }
 
 static void cxgbit_abort_arp_failure(void *handle, struct sk_buff *skb)
@@ -1136,7 +1139,7 @@ cxgbit_pass_accept_rpl(struct cxgbit_sock *csk, struct cpl_pass_accept_req *req)
 	rpl5->opt0 = cpu_to_be64(opt0);
 	rpl5->opt2 = cpu_to_be32(opt2);
 	set_wr_txq(skb, CPL_PRIORITY_SETUP, csk->ctrlq_idx);
-	t4_set_arp_err_handler(skb, NULL, cxgbit_arp_failure_discard);
+	t4_set_arp_err_handler(skb, csk, cxgbit_arp_failure_discard);
 	cxgbit_l2t_send(csk->com.cdev, skb, csk->l2t);
 }
 
-- 
2.19.1

[PATCH AUTOSEL 4.9 17/35] scsi: target: iscsi: cxgbit: add missing spin_lock_init()

[Sasha Levin]

From: Varun Prakash <varun@chelsio.com>

[ Upstream commit 9e6371d3c6913ff1707fb2c0274c9925f7aaef80 ]

Add missing spin_lock_init() for cdev->np_lock.

Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/target/iscsi/cxgbit/cxgbit_main.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/target/iscsi/cxgbit/cxgbit_main.c b/drivers/target/iscsi/cxgbit/cxgbit_main.c
index ad26b9372f10..d55261e1d522 100644
--- a/drivers/target/iscsi/cxgbit/cxgbit_main.c
+++ b/drivers/target/iscsi/cxgbit/cxgbit_main.c
@@ -58,6 +58,7 @@ static void *cxgbit_uld_add(const struct cxgb4_lld_info *lldi)
 		return ERR_PTR(-ENOMEM);
 
 	kref_init(&cdev->kref);
+	spin_lock_init(&cdev->np_lock);
 
 	cdev->lldi = *lldi;
 
-- 
2.19.1

[PATCH AUTOSEL 4.9 17/35] scsi: target: iscsi: cxgbit: add missing spin_lock_init()

[Sasha Levin]

From: Varun Prakash <varun@chelsio.com>

[ Upstream commit 9e6371d3c6913ff1707fb2c0274c9925f7aaef80 ]

Add missing spin_lock_init() for cdev->np_lock.

Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/target/iscsi/cxgbit/cxgbit_main.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/target/iscsi/cxgbit/cxgbit_main.c b/drivers/target/iscsi/cxgbit/cxgbit_main.c
index ad26b9372f10..d55261e1d522 100644
--- a/drivers/target/iscsi/cxgbit/cxgbit_main.c
+++ b/drivers/target/iscsi/cxgbit/cxgbit_main.c
@@ -58,6 +58,7 @@ static void *cxgbit_uld_add(const struct cxgb4_lld_info *lldi)
 		return ERR_PTR(-ENOMEM);
 
 	kref_init(&cdev->kref);
+	spin_lock_init(&cdev->np_lock);
 
 	cdev->lldi = *lldi;
 
-- 
2.19.1

[PATCH AUTOSEL 4.9 29/35] SUNRPC: Fix a race with XPRT_CONNECTING

[Sasha Levin]

From: Trond Myklebust <trond.myklebust@hammerspace.com>

[ Upstream commit cf76785d30712d90185455e752337acdb53d2a5d ]

Ensure that we clear XPRT_CONNECTING before releasing the XPRT_LOCK so that
we don't have races between the (asynchronous) socket setup code and
tasks in xprt_connect().

Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Tested-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/sunrpc/xprtsock.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/net/sunrpc/xprtsock.c b/net/sunrpc/xprtsock.c
index 1bf9153004cd..280fb3178708 100644
--- a/net/sunrpc/xprtsock.c
+++ b/net/sunrpc/xprtsock.c
@@ -2209,8 +2209,8 @@ static void xs_udp_setup_socket(struct work_struct *work)
 	trace_rpc_socket_connect(xprt, sock, 0);
 	status = 0;
 out:
-	xprt_unlock_connect(xprt, transport);
 	xprt_clear_connecting(xprt);
+	xprt_unlock_connect(xprt, transport);
 	xprt_wake_pending_tasks(xprt, status);
 }
 
@@ -2395,8 +2395,8 @@ static void xs_tcp_setup_socket(struct work_struct *work)
 	}
 	status = -EAGAIN;
 out:
-	xprt_unlock_connect(xprt, transport);
 	xprt_clear_connecting(xprt);
+	xprt_unlock_connect(xprt, transport);
 	xprt_wake_pending_tasks(xprt, status);
 }
 
-- 
2.19.1

[PATCH AUTOSEL 4.9 35/35] serial/sunsu: fix refcount leak

[Sasha Levin]

From: Yangtao Li <tiny.windzz@gmail.com>

[ Upstream commit d430aff8cd0c57502d873909c184e3b5753f8b88 ]

The function of_find_node_by_path() acquires a reference to the node
returned by it and that reference needs to be dropped by its caller.

su_get_type() doesn't do that. The match node are used as an identifier
to compare against the current node, so we can directly drop the refcount
after getting the node from the path as it is not used as pointer.

Fix this by use a single variable and drop the refcount right after
of_find_node_by_path().

Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/tty/serial/sunsu.c | 31 ++++++++++++++++++++++++++-----
 1 file changed, 26 insertions(+), 5 deletions(-)

diff --git a/drivers/tty/serial/sunsu.c b/drivers/tty/serial/sunsu.c
index 9ad98eaa35bf..26ae83026c52 100644
--- a/drivers/tty/serial/sunsu.c
+++ b/drivers/tty/serial/sunsu.c
@@ -1393,22 +1393,43 @@ static inline struct console *SUNSU_CONSOLE(void)
 static enum su_type su_get_type(struct device_node *dp)
 {
 	struct device_node *ap = of_find_node_by_path("/aliases");
+	enum su_type rc = SU_PORT_PORT;
 
 	if (ap) {
 		const char *keyb = of_get_property(ap, "keyboard", NULL);
 		const char *ms = of_get_property(ap, "mouse", NULL);
+		struct device_node *match;
 
 		if (keyb) {
-			if (dp == of_find_node_by_path(keyb))
-				return SU_PORT_KBD;
+			match = of_find_node_by_path(keyb);
+
+			/*
+			 * The pointer is used as an identifier not
+			 * as a pointer, we can drop the refcount on
+			 * the of__node immediately after getting it.
+			 */
+			of_node_put(match);
+
+			if (dp == match) {
+				rc = SU_PORT_KBD;
+				goto out;
+			}
 		}
 		if (ms) {
-			if (dp == of_find_node_by_path(ms))
-				return SU_PORT_MS;
+			match = of_find_node_by_path(ms);
+
+			of_node_put(match);
+
+			if (dp == match) {
+				rc = SU_PORT_MS;
+				goto out;
+			}
 		}
 	}
 
-	return SU_PORT_PORT;
+out:
+	of_node_put(ap);
+	return rc;
 }
 
 static int su_probe(struct platform_device *op)
-- 
2.19.1

[PATCH AUTOSEL 4.9 35/35] serial/sunsu: fix refcount leak

[Sasha Levin]

From: Yangtao Li <tiny.windzz@gmail.com>

[ Upstream commit d430aff8cd0c57502d873909c184e3b5753f8b88 ]

The function of_find_node_by_path() acquires a reference to the node
returned by it and that reference needs to be dropped by its caller.

su_get_type() doesn't do that. The match node are used as an identifier
to compare against the current node, so we can directly drop the refcount
after getting the node from the path as it is not used as pointer.

Fix this by use a single variable and drop the refcount right after
of_find_node_by_path().

Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/tty/serial/sunsu.c | 31 ++++++++++++++++++++++++++-----
 1 file changed, 26 insertions(+), 5 deletions(-)

diff --git a/drivers/tty/serial/sunsu.c b/drivers/tty/serial/sunsu.c
index 9ad98eaa35bf..26ae83026c52 100644
--- a/drivers/tty/serial/sunsu.c
+++ b/drivers/tty/serial/sunsu.c
@@ -1393,22 +1393,43 @@ static inline struct console *SUNSU_CONSOLE(void)
 static enum su_type su_get_type(struct device_node *dp)
 {
 	struct device_node *ap = of_find_node_by_path("/aliases");
+	enum su_type rc = SU_PORT_PORT;
 
 	if (ap) {
 		const char *keyb = of_get_property(ap, "keyboard", NULL);
 		const char *ms = of_get_property(ap, "mouse", NULL);
+		struct device_node *match;
 
 		if (keyb) {
-			if (dp = of_find_node_by_path(keyb))
-				return SU_PORT_KBD;
+			match = of_find_node_by_path(keyb);
+
+			/*
+			 * The pointer is used as an identifier not
+			 * as a pointer, we can drop the refcount on
+			 * the of__node immediately after getting it.
+			 */
+			of_node_put(match);
+
+			if (dp = match) {
+				rc = SU_PORT_KBD;
+				goto out;
+			}
 		}
 		if (ms) {
-			if (dp = of_find_node_by_path(ms))
-				return SU_PORT_MS;
+			match = of_find_node_by_path(ms);
+
+			of_node_put(match);
+
+			if (dp = match) {
+				rc = SU_PORT_MS;
+				goto out;
+			}
 		}
 	}
 
-	return SU_PORT_PORT;
+out:
+	of_node_put(ap);
+	return rc;
 }
 
 static int su_probe(struct platform_device *op)
-- 
2.19.1