From: Rob Herring <robh@kernel.org>
To: Philipp Puschmann <philipp.puschmann@emlix.com>
Cc: gregkh@linuxfoundation.org, robh+dt@kernel.org,
mark.rutland@arm.com, Peter.Chen@nxp.com,
linux-usb@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org
Subject: [v3,1/2] dt-bindings: usb: ci-hdrc-usb2: add property power-active-high
Date: Wed, 16 Jan 2019 13:51:08 -0600 [thread overview]
Message-ID: <20190116195108.GA18240@bogus> (raw)
On Wed, 16 Jan 2019 12:11:32 +0100, Philipp Puschmann wrote:
> The i.MX6q/dl USB controller may drive the usb power line directly, but the
> polarity depends on the board. Reset state of the polarity is low-active so
> add this property to allow it to be high-active.
>
> Signed-off-by: Philipp Puschmann <philipp.puschmann@emlix.com>
> ---
> Changes in v3: add description
> ---
> Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt | 1 +
> 1 file changed, 1 insertion(+)
>
Reviewed-by: Rob Herring <robh@kernel.org>
WARNING: multiple messages have this Message-ID (diff)
From: Rob Herring <robh@kernel.org>
Cc: gregkh@linuxfoundation.org, robh+dt@kernel.org,
mark.rutland@arm.com, Peter.Chen@nxp.com,
linux-usb@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org,
Philipp Puschmann <philipp.puschmann@emlix.com>
Subject: Re: [PATCH v3 1/2] dt-bindings: usb: ci-hdrc-usb2: add property power-active-high
Date: Wed, 16 Jan 2019 13:51:08 -0600 [thread overview]
Message-ID: <20190116195108.GA18240@bogus> (raw)
In-Reply-To: <20190116111133.31326-1-philipp.puschmann@emlix.com>
On Wed, 16 Jan 2019 12:11:32 +0100, Philipp Puschmann wrote:
> The i.MX6q/dl USB controller may drive the usb power line directly, but the
> polarity depends on the board. Reset state of the polarity is low-active so
> add this property to allow it to be high-active.
>
> Signed-off-by: Philipp Puschmann <philipp.puschmann@emlix.com>
> ---
> Changes in v3: add description
> ---
> Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt | 1 +
> 1 file changed, 1 insertion(+)
>
Reviewed-by: Rob Herring <robh@kernel.org>
WARNING: multiple messages have this Message-ID (diff)
From: Rob Herring <robh@kernel.org>
To: Philipp Puschmann <philipp.puschmann@emlix.com>
Cc: gregkh@linuxfoundation.org, robh+dt@kernel.org,
mark.rutland@arm.com, Peter.Chen@nxp.com,
linux-usb@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org,
Philipp Puschmann <philipp.puschmann@emlix.com>
Subject: Re: [PATCH v3 1/2] dt-bindings: usb: ci-hdrc-usb2: add property power-active-high
Date: Wed, 16 Jan 2019 13:51:08 -0600 [thread overview]
Message-ID: <20190116195108.GA18240@bogus> (raw)
In-Reply-To: <20190116111133.31326-1-philipp.puschmann@emlix.com>
On Wed, 16 Jan 2019 12:11:32 +0100, Philipp Puschmann wrote:
> The i.MX6q/dl USB controller may drive the usb power line directly, but the
> polarity depends on the board. Reset state of the polarity is low-active so
> add this property to allow it to be high-active.
>
> Signed-off-by: Philipp Puschmann <philipp.puschmann@emlix.com>
> ---
> Changes in v3: add description
> ---
> Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt | 1 +
> 1 file changed, 1 insertion(+)
>
Reviewed-by: Rob Herring <robh@kernel.org>
next reply other threads:[~2019-01-16 19:51 UTC|newest]
Thread overview: 25+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-01-16 19:51 Rob Herring [this message]
2019-01-16 19:51 ` [PATCH v3 1/2] dt-bindings: usb: ci-hdrc-usb2: add property power-active-high Rob Herring
2019-01-16 19:51 ` Rob Herring
-- strict thread matches above, loose matches on Subject: below --
2019-01-22 7:50 [v3,1/2] " Peter Chen
2019-01-22 7:50 ` [PATCH v3 1/2] " Peter Chen
2019-01-21 18:00 [v3,1/2] " Philipp Puschmann
2019-01-21 18:00 ` [PATCH v3 1/2] " Philipp Puschmann
2019-01-21 17:57 [v2,2/2] usb: chipidea: imx: set power polarity Philipp Puschmann
2019-01-21 17:57 ` [PATCH v2,2/2] " Philipp Puschmann
2019-01-17 7:01 [v3,1/2] dt-bindings: usb: ci-hdrc-usb2: add property power-active-high Peter Chen
2019-01-17 7:01 ` [PATCH v3 1/2] " Peter Chen
2019-01-16 16:32 [v2,2/2] usb: chipidea: imx: set power polarity Sergei Shtylyov
2019-01-16 16:32 ` [PATCH v2,2/2] " Sergei Shtylyov
2019-01-16 11:11 [v3,2/2] " Philipp Puschmann
2019-01-16 11:11 ` [PATCH v3 2/2] " Philipp Puschmann
2019-01-16 11:11 [v3,1/2] dt-bindings: usb: ci-hdrc-usb2: add property power-active-high Philipp Puschmann
2019-01-16 11:11 ` [PATCH v3 1/2] " Philipp Puschmann
2019-01-16 10:51 [v2,2/2] usb: chipidea: imx: set power polarity Philipp Puschmann
2019-01-16 10:51 ` [PATCH v2,2/2] " Philipp Puschmann
2019-01-16 10:51 [v2,1/2] dt-bindings: usb: ci-hdrc-usb2: add property power-active-high Philipp Puschmann
2019-01-16 10:51 ` [PATCH v2,1/2] " Philipp Puschmann
2019-01-15 12:31 [2/2] usb: chipidea: imx: set power polarity Philipp Puschmann
2019-01-15 12:31 ` [PATCH 2/2] " Philipp Puschmann
2019-01-15 12:31 [1/2] dt-bindings: usb: ci-hdrc-usb2: add property power-active-high Philipp Puschmann
2019-01-15 12:31 ` [PATCH 1/2] " Philipp Puschmann
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190116195108.GA18240@bogus \
--to=robh@kernel.org \
--cc=Peter.Chen@nxp.com \
--cc=devicetree@vger.kernel.org \
--cc=gregkh@linuxfoundation.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-usb@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=philipp.puschmann@emlix.com \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.