* [PATCH v3 1/2] dt-bindings: Add vendor prefix for Catalyst Semiconductor @ 2019-01-21 9:57 ` Martyn Welch 0 siblings, 0 replies; 10+ messages in thread From: Martyn Welch @ 2019-01-21 9:57 UTC (permalink / raw) To: Shawn Guo, Sascha Hauer, Rob Herring, Mark Rutland Cc: devicetree, Stefan Riedmüller, Rob Herring, Martyn Welch, Kevin Hilman, linux-kernel, Johan Hovold, Martin Blumenstingl, NXP Linux Team, Pengutronix Kernel Team, Christian Hemp, Fabio Estevam, Thierry Reding, Andreas Färber, linux-arm-kernel Add vendor prefix "catalyst" for Catalyst Semiconductor which is already in use but undocumented. Signed-off-by: Martyn Welch <martyn.welch@collabora.com> Reviewed-by: Rob Herring <robh@kernel.org> --- Changes in v3: - Add full stop to denote abbreviation. Changes in v2: None Documentation/devicetree/bindings/vendor-prefixes.txt | 1 + 1 file changed, 1 insertion(+) diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 389508584f48..a81de3134724 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -65,6 +65,7 @@ bticino Bticino International calxeda Calxeda capella Capella Microsystems, Inc cascoda Cascoda, Ltd. +catalyst Catalyst Semiconductor, Inc. cavium Cavium, Inc. cdns Cadence Design Systems Inc. cdtech CDTech(H.K.) Electronics Limited -- 2.20.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH v3 1/2] dt-bindings: Add vendor prefix for Catalyst Semiconductor @ 2019-01-21 9:57 ` Martyn Welch 0 siblings, 0 replies; 10+ messages in thread From: Martyn Welch @ 2019-01-21 9:57 UTC (permalink / raw) To: Shawn Guo, Sascha Hauer, Rob Herring, Mark Rutland Cc: Fabio Estevam, devicetree, Christian Hemp, Stefan Riedmüller, Pengutronix Kernel Team, linux-arm-kernel, NXP Linux Team, Martyn Welch, Rob Herring, Martin Blumenstingl, Thierry Reding, linux-kernel, Kevin Hilman, Johan Hovold, Andreas Färber Add vendor prefix "catalyst" for Catalyst Semiconductor which is already in use but undocumented. Signed-off-by: Martyn Welch <martyn.welch@collabora.com> Reviewed-by: Rob Herring <robh@kernel.org> --- Changes in v3: - Add full stop to denote abbreviation. Changes in v2: None Documentation/devicetree/bindings/vendor-prefixes.txt | 1 + 1 file changed, 1 insertion(+) diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 389508584f48..a81de3134724 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -65,6 +65,7 @@ bticino Bticino International calxeda Calxeda capella Capella Microsystems, Inc cascoda Cascoda, Ltd. +catalyst Catalyst Semiconductor, Inc. cavium Cavium, Inc. cdns Cadence Design Systems Inc. cdtech CDTech(H.K.) Electronics Limited -- 2.20.1 ^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH v3 2/2] ARM: dts: imx6: Add support for Phytec phyBOARD i.MX6UL Segin 2019-01-21 9:57 ` Martyn Welch @ 2019-01-21 9:57 ` Martyn Welch -1 siblings, 0 replies; 10+ messages in thread From: Martyn Welch @ 2019-01-21 9:57 UTC (permalink / raw) To: Shawn Guo, Sascha Hauer, Rob Herring, Mark Rutland Cc: devicetree, Stefan Riedmüller, Martyn Welch, linux-kernel, NXP Linux Team, Pengutronix Kernel Team, Christian Hemp, Fabio Estevam, linux-arm-kernel The Phytec phyBOARD Segin is i.MX6 based SBC, available with either an i.MX6UL or i.MX6ULL SOM and various add-on boards. The following adds support for the "Full Featured" version of the Segin, which is provided with the i.MX6UL SOM and the PEB-EVAL-01 evaluation module. Its hardware specifications are: * 512MB DDR3 memory * 512MB NAND flash * Dual 10/100 Ethernet * USB Host and USB OTG * RS232 * MicroSD external storage * Audio, RS232, I2C, SPI, CAN headers * Further I/O options via A/V and Expansion headers Signed-off-by: Martyn Welch <martyn.welch@collabora.com> --- Changes in v3: - Add memory device_type property - Remove unneeded pinctrl-names property - Keep compatible string on a single line - Make node names generic and labels specific Changes in v2: - Corrected spacing, ordering and naming - Corrected ecspi3 chip selects - Updated deprecated node - Removed unneeded nodes arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/imx6ul-phytec-pcl063.dtsi | 148 ++++++++ .../boot/dts/imx6ul-phytec-peb-eval-01.dtsi | 55 +++ .../dts/imx6ul-phytec-phyboard-segin-full.dts | 89 +++++ .../dts/imx6ul-phytec-phyboard-segin.dtsi | 329 ++++++++++++++++++ 5 files changed, 622 insertions(+) create mode 100644 arch/arm/boot/dts/imx6ul-phytec-pcl063.dtsi create mode 100644 arch/arm/boot/dts/imx6ul-phytec-peb-eval-01.dtsi create mode 100644 arch/arm/boot/dts/imx6ul-phytec-phyboard-segin-full.dts create mode 100644 arch/arm/boot/dts/imx6ul-phytec-phyboard-segin.dtsi diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index bd40148a15b2..d35a0bf7b8f8 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -561,6 +561,7 @@ dtb-$(CONFIG_SOC_IMX6UL) += \ imx6ul-opos6uldev.dtb \ imx6ul-pico-hobbit.dtb \ imx6ul-pico-pi.dtb \ + imx6ul-phytec-phyboard-segin-full.dtb \ imx6ul-tx6ul-0010.dtb \ imx6ul-tx6ul-0011.dtb \ imx6ul-tx6ul-mainboard.dtb \ diff --git a/arch/arm/boot/dts/imx6ul-phytec-pcl063.dtsi b/arch/arm/boot/dts/imx6ul-phytec-pcl063.dtsi new file mode 100644 index 000000000000..fc2997449b49 --- /dev/null +++ b/arch/arm/boot/dts/imx6ul-phytec-pcl063.dtsi @@ -0,0 +1,148 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2016 PHYTEC Messtechnik GmbH + * Author: Christian Hemp <c.hemp@phytec.de> + */ + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/pwm/pwm.h> +#include "imx6ul.dtsi" + +/ { + model = "Phytec phyCORE i.MX6 UltraLite"; + compatible = "phytec,imx6ul-pcl063", "fsl,imx6ul"; + + chosen { + stdout-path = &uart1; + }; + + /* + * Set the minimum memory size here and + * let the bootloader set the real size. + */ + memory { + device_type = "memory"; + reg = <0x80000000 0x8000000>; + }; + + gpio_leds_som: leds { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpioleds_som>; + compatible = "gpio-leds"; + + led_green { + label = "phycore:green"; + gpios = <&gpio5 4 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + }; + }; +}; + +&fec1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet1>; + phy-mode = "rmii"; + phy-handle = <ðphy0>; + status = "okay"; + + mdio: mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy0: ethernet-phy@1 { + reg = <1>; + interrupt-parent = <&gpio1>; + interrupts = <2 IRQ_TYPE_LEVEL_LOW>; + micrel,led-mode = <1>; + clocks = <&clks IMX6UL_CLK_ENET_REF>; + clock-names = "rmii-ref"; + }; + }; +}; + +&gpmi { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpmi_nand>; + nand-on-flash-bbt; + status = "okay"; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 =<&pinctrl_i2c1>; + clock-frequency = <100000>; + status = "okay"; + + eeprom@52 { + compatible = "catalyst,24c32", "atmel,24c32"; + reg = <0x52>; + }; +}; + +&snvs_poweroff { + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +&iomuxc { + pinctrl_enet1: enet1grp { + fsl,pins = < + MX6UL_PAD_GPIO1_IO07__ENET1_MDC 0x1b0b0 + MX6UL_PAD_GPIO1_IO06__ENET1_MDIO 0x1b0b0 + MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN 0x1b0b0 + MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER 0x1b0b0 + MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x1b0b0 + MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x1b0b0 + MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN 0x1b0b0 + MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x1b0b0 + MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x1b0b0 + MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 0x4001b031 + MX6UL_PAD_GPIO1_IO02__GPIO1_IO02 0x17059 + >; + }; + + pinctrl_gpioleds_som: gpioledssomgrp { + fsl,pins = <MX6UL_PAD_SNVS_TAMPER4__GPIO5_IO04 0x0b0b0>; + }; + + pinctrl_gpmi_nand: gpminandgrp { + fsl,pins = < + MX6UL_PAD_NAND_CLE__RAWNAND_CLE 0x0b0b1 + MX6UL_PAD_NAND_ALE__RAWNAND_ALE 0x0b0b1 + MX6UL_PAD_NAND_WP_B__RAWNAND_WP_B 0x0b0b1 + MX6UL_PAD_NAND_READY_B__RAWNAND_READY_B 0x0b000 + MX6UL_PAD_NAND_CE0_B__RAWNAND_CE0_B 0x0b0b1 + MX6UL_PAD_NAND_RE_B__RAWNAND_RE_B 0x0b0b1 + MX6UL_PAD_NAND_WE_B__RAWNAND_WE_B 0x0b0b1 + MX6UL_PAD_NAND_DATA00__RAWNAND_DATA00 0x0b0b1 + MX6UL_PAD_NAND_DATA01__RAWNAND_DATA01 0x0b0b1 + MX6UL_PAD_NAND_DATA02__RAWNAND_DATA02 0x0b0b1 + MX6UL_PAD_NAND_DATA03__RAWNAND_DATA03 0x0b0b1 + MX6UL_PAD_NAND_DATA04__RAWNAND_DATA04 0x0b0b1 + MX6UL_PAD_NAND_DATA05__RAWNAND_DATA05 0x0b0b1 + MX6UL_PAD_NAND_DATA06__RAWNAND_DATA06 0x0b0b1 + MX6UL_PAD_NAND_DATA07__RAWNAND_DATA07 0x0b0b1 + >; + }; + + pinctrl_i2c1: i2cgrp { + fsl,pins = < + MX6UL_PAD_UART4_TX_DATA__I2C1_SCL 0x4001b8b0 + MX6UL_PAD_UART4_RX_DATA__I2C1_SDA 0x4001b8b0 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x1b0b1 + MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX 0x1b0b1 + >; + }; + +}; diff --git a/arch/arm/boot/dts/imx6ul-phytec-peb-eval-01.dtsi b/arch/arm/boot/dts/imx6ul-phytec-peb-eval-01.dtsi new file mode 100644 index 000000000000..e2f38f39a6ad --- /dev/null +++ b/arch/arm/boot/dts/imx6ul-phytec-peb-eval-01.dtsi @@ -0,0 +1,55 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2016 PHYTEC Messtechnik + * Author: Christian Hemp <c.hemp@phytec.de> + */ + +#include <dt-bindings/input/input.h> + +/ { + gpio_keys: gpio-keys { + compatible = "gpio-key"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpio_keys>; + status = "disabled"; + + power { + label = "Power Button"; + gpios = <&gpio5 0 GPIO_ACTIVE_LOW>; + linux,code = <KEY_POWER>; + wakeup-source; + }; + }; + + user_leds: leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_user_leds>; + status = "disabled"; + + led_yellow { + gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "default-on"; + }; + + led_red { + gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "default-on"; + }; + }; +}; + +&iomuxc { + pinctrl_gpio_keys: gpio_keysgrp { + fsl,pins = < + MX6UL_PAD_SNVS_TAMPER0__GPIO5_IO00 0x79 + >; + }; + + pinctrl_user_leds: user_ledsgrp { + fsl,pins = < + MX6UL_PAD_JTAG_MOD__GPIO1_IO10 0x79 + MX6UL_PAD_GPIO1_IO01__GPIO1_IO01 0x79 + >; + }; +}; diff --git a/arch/arm/boot/dts/imx6ul-phytec-phyboard-segin-full.dts b/arch/arm/boot/dts/imx6ul-phytec-phyboard-segin-full.dts new file mode 100644 index 000000000000..b6a1407a9d44 --- /dev/null +++ b/arch/arm/boot/dts/imx6ul-phytec-phyboard-segin-full.dts @@ -0,0 +1,89 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2016 PHYTEC Messtechnik GmbH + * Author: Christian Hemp <c.hemp@phytec.de> + */ + +/dts-v1/; +#include "imx6ul-phytec-pcl063.dtsi" +#include "imx6ul-phytec-phyboard-segin.dtsi" +#include "imx6ul-phytec-peb-eval-01.dtsi" + +/ { + model = "Phytec phyBOARD-Segin i.MX6 UltraLite Full Featured"; + compatible = "phytec,imx6ul-pbacd10", "phytec,imx6ul-pcl063", "fsl,imx6ul"; +}; + +&adc1 { + status = "okay"; +}; + +&can1 { + status = "okay"; +}; + +&tlv320 { + status = "okay"; +}; + +&ecspi3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi3>; + cs-gpios = <&gpio1 20 GPIO_ACTIVE_HIGH>; + status = "okay"; +}; + +&fec2 { + status = "okay"; +}; + +&i2c_rtc { + status = "okay"; +}; + +®_can1_en { + status = "okay"; +}; + +®_sound_1v8 { + status = "okay"; +}; + +®_sound_3v3 { + status = "okay"; +}; + +&sai2 { + status = "okay"; +}; + +&sound { + status = "okay"; +}; + +&uart5 { + status = "okay"; +}; + +&usbotg1 { + status = "okay"; +}; + +&usbotg2 { + status = "okay"; +}; + +&usdhc1 { + status = "okay"; +}; + +&iomuxc { + pinctrl_ecspi3: ecspi3grp { + fsl,pins = < + MX6UL_PAD_UART2_RTS_B__ECSPI3_MISO 0x10b0 + MX6UL_PAD_UART2_CTS_B__ECSPI3_MOSI 0x10b0 + MX6UL_PAD_UART2_RX_DATA__ECSPI3_SCLK 0x10b0 + MX6UL_PAD_UART2_TX_DATA__GPIO1_IO20 0x10b0 + >; + }; +}; diff --git a/arch/arm/boot/dts/imx6ul-phytec-phyboard-segin.dtsi b/arch/arm/boot/dts/imx6ul-phytec-phyboard-segin.dtsi new file mode 100644 index 000000000000..7bf439a77d2c --- /dev/null +++ b/arch/arm/boot/dts/imx6ul-phytec-phyboard-segin.dtsi @@ -0,0 +1,329 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2016 PHYTEC Messtechnik GmbH + * Author: Christian Hemp <c.hemp@phytec.de> + */ + +/ { + model = "Phytec phyBOARD-Segin i.MX6 UltraLite"; + compatible = "phytec,imx6ul-pbacd-10", "phytec,imx6ul-pcl063", "fsl,imx6ul"; + + aliases { + rtc0 = &i2c_rtc; + rtc1 = &snvs_rtc; + }; + + reg_sound_1v8: regulator-1v8 { + compatible = "regulator-fixed"; + regulator-name = "i2s-audio-1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + status = "disabled"; + }; + + reg_sound_3v3: regulator-3v3 { + compatible = "regulator-fixed"; + regulator-name = "i2s-audio-3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + status = "disabled"; + }; + + reg_can1_en: regulator-can1 { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&princtrl_flexcan1_en>; + regulator-name = "Can"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>; + enable-active-high; + status = "disabled"; + }; + + reg_adc1_vref_3v3: regulator-vref-3v3 { + compatible = "regulator-fixed"; + regulator-name = "vref-3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + sound: sound { + compatible = "simple-audio-card"; + simple-audio-card,name = "phyBOARD-Segin-TLV320AIC3007"; + simple-audio-card,format = "i2s"; + simple-audio-card,bitclock-master = <&dailink_master>; + simple-audio-card,frame-master = <&dailink_master>; + simple-audio-card,widgets = + "Line", "Line In", + "Line", "Line Out", + "Speaker", "Speaker"; + simple-audio-card,routing = + "Line Out", "LLOUT", + "Line Out", "RLOUT", + "Speaker", "SPOP", + "Speaker", "SPOM", + "LINE1L", "Line In", + "LINE1R", "Line In"; + status = "disabled"; + + simple-audio-card,cpu { + sound-dai = <&sai2>; + }; + + dailink_master: simple-audio-card,codec { + sound-dai = <&tlv320>; + clocks = <&clks IMX6UL_CLK_SAI2>; + }; + }; + +}; + +&adc1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_adc1>; + vref-supply = <®_adc1_vref_3v3>; + /* + * driver can not separate a specific channel so we request 4 channels + * here - we need only the fourth channel + */ + num-channels = <4>; + status = "disabled"; +}; + +&can1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexcan1>; + xceiver-supply = <®_can1_en>; + status = "disabled"; +}; + +&clks { + assigned-clocks = <&clks IMX6UL_CLK_PLL4_AUDIO_DIV>; + assigned-clock-rates = <786432000>; +}; + +&fec2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet2>; + phy-mode = "rmii"; + phy-handle = <ðphy1>; + status = "disabled"; +}; + +&i2c1 { + tlv320: codec@18 { + compatible = "ti,tlv320aic3007"; + #sound-dai-cells = <0>; + reg = <0x18>; + AVDD-supply = <®_sound_3v3>; + IOVDD-supply = <®_sound_3v3>; + DRVDD-supply = <®_sound_3v3>; + DVDD-supply = <®_sound_1v8>; + status = "disabled"; + }; + + stmpe: touchscreen@44 { + compatible = "st,stmpe811"; + reg = <0x44>; + interrupts = <3 IRQ_TYPE_LEVEL_LOW>; + interrupt-parent = <&gpio5>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_stmpe>; + status = "disabled"; + + touchscreen { + compatible = "st,stmpe-ts"; + st,sample-time = <4>; + st,mod-12b = <1>; + st,ref-sel = <0>; + st,adc-freq = <1>; + st,ave-ctrl = <1>; + st,touch-det-delay = <2>; + st,settling = <2>; + st,fraction-z = <7>; + st,i-drive = <1>; + touchscreen-inverted-x = <1>; + touchscreen-inverted-y = <1>; + }; + }; + + i2c_rtc: rtc@68 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_rtc_int>; + compatible = "microcrystal,rv4162"; + reg = <0x68>; + interrupt-parent = <&gpio5>; + interrupts = <1 IRQ_TYPE_LEVEL_LOW>; + status = "disabled"; + }; +}; + +&mdio { + ethphy1: ethernet-phy@2 { + reg = <2>; + micrel,led-mode = <1>; + clocks = <&clks IMX6UL_CLK_ENET2_REF>; + clock-names = "rmii-ref"; + }; +}; + +&pwm3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm3>; + status = "disabled"; +}; + +&sai2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sai2>; + assigned-clocks = <&clks IMX6UL_CLK_SAI2_SEL>, + <&clks IMX6UL_CLK_SAI2>; + assigned-clock-parents = <&clks IMX6UL_CLK_PLL4_AUDIO_DIV>; + assigned-clock-rates = <0>, <19200000>; + fsl,sai-mclk-direction-output; + status = "disabled"; +}; + +&uart5 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart5>; + uart-has-rtscts; + status = "disabled"; +}; + +&usbotg1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb_otg1_id>; + dr_mode = "otg"; + status = "disabled"; +}; + +&usbotg2 { + dr_mode = "host"; + disable-over-current; + status = "disabled"; +}; + +&usdhc1 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc1>; + pinctrl-1 = <&pinctrl_usdhc1_100mhz>; + pinctrl-2 = <&pinctrl_usdhc1_200mhz>; + cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>; + no-1-8-v; + keep-power-in-suspend; + wakeup-source; + status = "disabled"; +}; + +&iomuxc { + pinctrl_adc1: adc1grp { + fsl,pins = < + MX6UL_PAD_GPIO1_IO03__GPIO1_IO03 0xb0 + >; + }; + + pinctrl_enet2: enet2grp { + fsl,pins = < + MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN 0x1b0b0 + MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER 0x1b0b0 + MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00 0x1b0b0 + MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01 0x1b0b0 + MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN 0x1b0b0 + MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00 0x1b0b0 + MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01 0x1b0b0 + MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 0x4001b031 + >; + }; + + pinctrl_flexcan1: flexcan1 { + fsl,pins = < + MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX 0x0b0b0 + MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX 0x0b0b0 + >; + }; + + princtrl_flexcan1_en: flexcan1engrp { + fsl,pins = < + MX6UL_PAD_SNVS_TAMPER2__GPIO5_IO02 0x17059 + >; + }; + + pinctrl_pwm3: pwm3grp { + fsl,pins = < + MX6UL_PAD_GPIO1_IO04__PWM3_OUT 0x0b0b0 + >; + }; + + pinctrl_rtc_int: rtcintgrp { + fsl,pins = < + MX6UL_PAD_SNVS_TAMPER1__GPIO5_IO01 0x17059 + >; + }; + + pinctrl_sai2: sai2grp { + fsl,pins = < + MX6UL_PAD_JTAG_TDI__SAI2_TX_BCLK 0x17088 + MX6UL_PAD_JTAG_TDO__SAI2_TX_SYNC 0x17088 + MX6UL_PAD_JTAG_TRST_B__SAI2_TX_DATA 0x11088 + MX6UL_PAD_JTAG_TCK__SAI2_RX_DATA 0x11088 + MX6UL_PAD_JTAG_TMS__SAI2_MCLK 0x17088 + >; + }; + + pinctrl_stmpe: stmpegrp { + fsl,pins = < + MX6UL_PAD_SNVS_TAMPER3__GPIO5_IO03 0x17059 + >; + }; + + pinctrl_uart5: uart5grp { + fsl,pins = < + MX6UL_PAD_UART5_TX_DATA__UART5_DCE_TX 0x1b0b1 + MX6UL_PAD_UART5_RX_DATA__UART5_DCE_RX 0x1b0b1 + MX6UL_PAD_GPIO1_IO08__UART5_DCE_RTS 0x1b0b1 + MX6UL_PAD_GPIO1_IO09__UART5_DCE_CTS 0x1b0b1 + >; + }; + + pinctrl_usb_otg1_id: usbotg1idgrp { + fsl,pins = < + MX6UL_PAD_GPIO1_IO00__ANATOP_OTG1_ID 0x17059 + >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x17059 + MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x10059 + MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x17059 + MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x17059 + MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x17059 + MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x17059 + MX6UL_PAD_UART1_RTS_B__GPIO1_IO19 0x17059 + >; + }; + + pinctrl_usdhc1_100mhz: usdhc1grp100mhz { + fsl,pins = < + MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x170b9 + MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x100b9 + MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x170b9 + MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x170b9 + MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x170b9 + MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x170b9 + >; + }; + + pinctrl_usdhc1_200mhz: usdhc1grp200mhz { + fsl,pins = < + MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x170f9 + MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x100f9 + MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x170f9 + MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x170f9 + MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x170f9 + MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x170f9 + >; + }; +}; -- 2.20.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH v3 2/2] ARM: dts: imx6: Add support for Phytec phyBOARD i.MX6UL Segin @ 2019-01-21 9:57 ` Martyn Welch 0 siblings, 0 replies; 10+ messages in thread From: Martyn Welch @ 2019-01-21 9:57 UTC (permalink / raw) To: Shawn Guo, Sascha Hauer, Rob Herring, Mark Rutland Cc: Fabio Estevam, devicetree, Christian Hemp, Stefan Riedmüller, Pengutronix Kernel Team, linux-arm-kernel, NXP Linux Team, Martyn Welch, linux-kernel The Phytec phyBOARD Segin is i.MX6 based SBC, available with either an i.MX6UL or i.MX6ULL SOM and various add-on boards. The following adds support for the "Full Featured" version of the Segin, which is provided with the i.MX6UL SOM and the PEB-EVAL-01 evaluation module. Its hardware specifications are: * 512MB DDR3 memory * 512MB NAND flash * Dual 10/100 Ethernet * USB Host and USB OTG * RS232 * MicroSD external storage * Audio, RS232, I2C, SPI, CAN headers * Further I/O options via A/V and Expansion headers Signed-off-by: Martyn Welch <martyn.welch@collabora.com> --- Changes in v3: - Add memory device_type property - Remove unneeded pinctrl-names property - Keep compatible string on a single line - Make node names generic and labels specific Changes in v2: - Corrected spacing, ordering and naming - Corrected ecspi3 chip selects - Updated deprecated node - Removed unneeded nodes arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/imx6ul-phytec-pcl063.dtsi | 148 ++++++++ .../boot/dts/imx6ul-phytec-peb-eval-01.dtsi | 55 +++ .../dts/imx6ul-phytec-phyboard-segin-full.dts | 89 +++++ .../dts/imx6ul-phytec-phyboard-segin.dtsi | 329 ++++++++++++++++++ 5 files changed, 622 insertions(+) create mode 100644 arch/arm/boot/dts/imx6ul-phytec-pcl063.dtsi create mode 100644 arch/arm/boot/dts/imx6ul-phytec-peb-eval-01.dtsi create mode 100644 arch/arm/boot/dts/imx6ul-phytec-phyboard-segin-full.dts create mode 100644 arch/arm/boot/dts/imx6ul-phytec-phyboard-segin.dtsi diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index bd40148a15b2..d35a0bf7b8f8 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -561,6 +561,7 @@ dtb-$(CONFIG_SOC_IMX6UL) += \ imx6ul-opos6uldev.dtb \ imx6ul-pico-hobbit.dtb \ imx6ul-pico-pi.dtb \ + imx6ul-phytec-phyboard-segin-full.dtb \ imx6ul-tx6ul-0010.dtb \ imx6ul-tx6ul-0011.dtb \ imx6ul-tx6ul-mainboard.dtb \ diff --git a/arch/arm/boot/dts/imx6ul-phytec-pcl063.dtsi b/arch/arm/boot/dts/imx6ul-phytec-pcl063.dtsi new file mode 100644 index 000000000000..fc2997449b49 --- /dev/null +++ b/arch/arm/boot/dts/imx6ul-phytec-pcl063.dtsi @@ -0,0 +1,148 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2016 PHYTEC Messtechnik GmbH + * Author: Christian Hemp <c.hemp@phytec.de> + */ + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/pwm/pwm.h> +#include "imx6ul.dtsi" + +/ { + model = "Phytec phyCORE i.MX6 UltraLite"; + compatible = "phytec,imx6ul-pcl063", "fsl,imx6ul"; + + chosen { + stdout-path = &uart1; + }; + + /* + * Set the minimum memory size here and + * let the bootloader set the real size. + */ + memory { + device_type = "memory"; + reg = <0x80000000 0x8000000>; + }; + + gpio_leds_som: leds { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpioleds_som>; + compatible = "gpio-leds"; + + led_green { + label = "phycore:green"; + gpios = <&gpio5 4 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + }; + }; +}; + +&fec1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet1>; + phy-mode = "rmii"; + phy-handle = <ðphy0>; + status = "okay"; + + mdio: mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy0: ethernet-phy@1 { + reg = <1>; + interrupt-parent = <&gpio1>; + interrupts = <2 IRQ_TYPE_LEVEL_LOW>; + micrel,led-mode = <1>; + clocks = <&clks IMX6UL_CLK_ENET_REF>; + clock-names = "rmii-ref"; + }; + }; +}; + +&gpmi { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpmi_nand>; + nand-on-flash-bbt; + status = "okay"; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 =<&pinctrl_i2c1>; + clock-frequency = <100000>; + status = "okay"; + + eeprom@52 { + compatible = "catalyst,24c32", "atmel,24c32"; + reg = <0x52>; + }; +}; + +&snvs_poweroff { + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +&iomuxc { + pinctrl_enet1: enet1grp { + fsl,pins = < + MX6UL_PAD_GPIO1_IO07__ENET1_MDC 0x1b0b0 + MX6UL_PAD_GPIO1_IO06__ENET1_MDIO 0x1b0b0 + MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN 0x1b0b0 + MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER 0x1b0b0 + MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x1b0b0 + MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x1b0b0 + MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN 0x1b0b0 + MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x1b0b0 + MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x1b0b0 + MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 0x4001b031 + MX6UL_PAD_GPIO1_IO02__GPIO1_IO02 0x17059 + >; + }; + + pinctrl_gpioleds_som: gpioledssomgrp { + fsl,pins = <MX6UL_PAD_SNVS_TAMPER4__GPIO5_IO04 0x0b0b0>; + }; + + pinctrl_gpmi_nand: gpminandgrp { + fsl,pins = < + MX6UL_PAD_NAND_CLE__RAWNAND_CLE 0x0b0b1 + MX6UL_PAD_NAND_ALE__RAWNAND_ALE 0x0b0b1 + MX6UL_PAD_NAND_WP_B__RAWNAND_WP_B 0x0b0b1 + MX6UL_PAD_NAND_READY_B__RAWNAND_READY_B 0x0b000 + MX6UL_PAD_NAND_CE0_B__RAWNAND_CE0_B 0x0b0b1 + MX6UL_PAD_NAND_RE_B__RAWNAND_RE_B 0x0b0b1 + MX6UL_PAD_NAND_WE_B__RAWNAND_WE_B 0x0b0b1 + MX6UL_PAD_NAND_DATA00__RAWNAND_DATA00 0x0b0b1 + MX6UL_PAD_NAND_DATA01__RAWNAND_DATA01 0x0b0b1 + MX6UL_PAD_NAND_DATA02__RAWNAND_DATA02 0x0b0b1 + MX6UL_PAD_NAND_DATA03__RAWNAND_DATA03 0x0b0b1 + MX6UL_PAD_NAND_DATA04__RAWNAND_DATA04 0x0b0b1 + MX6UL_PAD_NAND_DATA05__RAWNAND_DATA05 0x0b0b1 + MX6UL_PAD_NAND_DATA06__RAWNAND_DATA06 0x0b0b1 + MX6UL_PAD_NAND_DATA07__RAWNAND_DATA07 0x0b0b1 + >; + }; + + pinctrl_i2c1: i2cgrp { + fsl,pins = < + MX6UL_PAD_UART4_TX_DATA__I2C1_SCL 0x4001b8b0 + MX6UL_PAD_UART4_RX_DATA__I2C1_SDA 0x4001b8b0 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x1b0b1 + MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX 0x1b0b1 + >; + }; + +}; diff --git a/arch/arm/boot/dts/imx6ul-phytec-peb-eval-01.dtsi b/arch/arm/boot/dts/imx6ul-phytec-peb-eval-01.dtsi new file mode 100644 index 000000000000..e2f38f39a6ad --- /dev/null +++ b/arch/arm/boot/dts/imx6ul-phytec-peb-eval-01.dtsi @@ -0,0 +1,55 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2016 PHYTEC Messtechnik + * Author: Christian Hemp <c.hemp@phytec.de> + */ + +#include <dt-bindings/input/input.h> + +/ { + gpio_keys: gpio-keys { + compatible = "gpio-key"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpio_keys>; + status = "disabled"; + + power { + label = "Power Button"; + gpios = <&gpio5 0 GPIO_ACTIVE_LOW>; + linux,code = <KEY_POWER>; + wakeup-source; + }; + }; + + user_leds: leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_user_leds>; + status = "disabled"; + + led_yellow { + gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "default-on"; + }; + + led_red { + gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "default-on"; + }; + }; +}; + +&iomuxc { + pinctrl_gpio_keys: gpio_keysgrp { + fsl,pins = < + MX6UL_PAD_SNVS_TAMPER0__GPIO5_IO00 0x79 + >; + }; + + pinctrl_user_leds: user_ledsgrp { + fsl,pins = < + MX6UL_PAD_JTAG_MOD__GPIO1_IO10 0x79 + MX6UL_PAD_GPIO1_IO01__GPIO1_IO01 0x79 + >; + }; +}; diff --git a/arch/arm/boot/dts/imx6ul-phytec-phyboard-segin-full.dts b/arch/arm/boot/dts/imx6ul-phytec-phyboard-segin-full.dts new file mode 100644 index 000000000000..b6a1407a9d44 --- /dev/null +++ b/arch/arm/boot/dts/imx6ul-phytec-phyboard-segin-full.dts @@ -0,0 +1,89 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2016 PHYTEC Messtechnik GmbH + * Author: Christian Hemp <c.hemp@phytec.de> + */ + +/dts-v1/; +#include "imx6ul-phytec-pcl063.dtsi" +#include "imx6ul-phytec-phyboard-segin.dtsi" +#include "imx6ul-phytec-peb-eval-01.dtsi" + +/ { + model = "Phytec phyBOARD-Segin i.MX6 UltraLite Full Featured"; + compatible = "phytec,imx6ul-pbacd10", "phytec,imx6ul-pcl063", "fsl,imx6ul"; +}; + +&adc1 { + status = "okay"; +}; + +&can1 { + status = "okay"; +}; + +&tlv320 { + status = "okay"; +}; + +&ecspi3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi3>; + cs-gpios = <&gpio1 20 GPIO_ACTIVE_HIGH>; + status = "okay"; +}; + +&fec2 { + status = "okay"; +}; + +&i2c_rtc { + status = "okay"; +}; + +®_can1_en { + status = "okay"; +}; + +®_sound_1v8 { + status = "okay"; +}; + +®_sound_3v3 { + status = "okay"; +}; + +&sai2 { + status = "okay"; +}; + +&sound { + status = "okay"; +}; + +&uart5 { + status = "okay"; +}; + +&usbotg1 { + status = "okay"; +}; + +&usbotg2 { + status = "okay"; +}; + +&usdhc1 { + status = "okay"; +}; + +&iomuxc { + pinctrl_ecspi3: ecspi3grp { + fsl,pins = < + MX6UL_PAD_UART2_RTS_B__ECSPI3_MISO 0x10b0 + MX6UL_PAD_UART2_CTS_B__ECSPI3_MOSI 0x10b0 + MX6UL_PAD_UART2_RX_DATA__ECSPI3_SCLK 0x10b0 + MX6UL_PAD_UART2_TX_DATA__GPIO1_IO20 0x10b0 + >; + }; +}; diff --git a/arch/arm/boot/dts/imx6ul-phytec-phyboard-segin.dtsi b/arch/arm/boot/dts/imx6ul-phytec-phyboard-segin.dtsi new file mode 100644 index 000000000000..7bf439a77d2c --- /dev/null +++ b/arch/arm/boot/dts/imx6ul-phytec-phyboard-segin.dtsi @@ -0,0 +1,329 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2016 PHYTEC Messtechnik GmbH + * Author: Christian Hemp <c.hemp@phytec.de> + */ + +/ { + model = "Phytec phyBOARD-Segin i.MX6 UltraLite"; + compatible = "phytec,imx6ul-pbacd-10", "phytec,imx6ul-pcl063", "fsl,imx6ul"; + + aliases { + rtc0 = &i2c_rtc; + rtc1 = &snvs_rtc; + }; + + reg_sound_1v8: regulator-1v8 { + compatible = "regulator-fixed"; + regulator-name = "i2s-audio-1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + status = "disabled"; + }; + + reg_sound_3v3: regulator-3v3 { + compatible = "regulator-fixed"; + regulator-name = "i2s-audio-3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + status = "disabled"; + }; + + reg_can1_en: regulator-can1 { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&princtrl_flexcan1_en>; + regulator-name = "Can"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>; + enable-active-high; + status = "disabled"; + }; + + reg_adc1_vref_3v3: regulator-vref-3v3 { + compatible = "regulator-fixed"; + regulator-name = "vref-3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + sound: sound { + compatible = "simple-audio-card"; + simple-audio-card,name = "phyBOARD-Segin-TLV320AIC3007"; + simple-audio-card,format = "i2s"; + simple-audio-card,bitclock-master = <&dailink_master>; + simple-audio-card,frame-master = <&dailink_master>; + simple-audio-card,widgets = + "Line", "Line In", + "Line", "Line Out", + "Speaker", "Speaker"; + simple-audio-card,routing = + "Line Out", "LLOUT", + "Line Out", "RLOUT", + "Speaker", "SPOP", + "Speaker", "SPOM", + "LINE1L", "Line In", + "LINE1R", "Line In"; + status = "disabled"; + + simple-audio-card,cpu { + sound-dai = <&sai2>; + }; + + dailink_master: simple-audio-card,codec { + sound-dai = <&tlv320>; + clocks = <&clks IMX6UL_CLK_SAI2>; + }; + }; + +}; + +&adc1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_adc1>; + vref-supply = <®_adc1_vref_3v3>; + /* + * driver can not separate a specific channel so we request 4 channels + * here - we need only the fourth channel + */ + num-channels = <4>; + status = "disabled"; +}; + +&can1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexcan1>; + xceiver-supply = <®_can1_en>; + status = "disabled"; +}; + +&clks { + assigned-clocks = <&clks IMX6UL_CLK_PLL4_AUDIO_DIV>; + assigned-clock-rates = <786432000>; +}; + +&fec2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet2>; + phy-mode = "rmii"; + phy-handle = <ðphy1>; + status = "disabled"; +}; + +&i2c1 { + tlv320: codec@18 { + compatible = "ti,tlv320aic3007"; + #sound-dai-cells = <0>; + reg = <0x18>; + AVDD-supply = <®_sound_3v3>; + IOVDD-supply = <®_sound_3v3>; + DRVDD-supply = <®_sound_3v3>; + DVDD-supply = <®_sound_1v8>; + status = "disabled"; + }; + + stmpe: touchscreen@44 { + compatible = "st,stmpe811"; + reg = <0x44>; + interrupts = <3 IRQ_TYPE_LEVEL_LOW>; + interrupt-parent = <&gpio5>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_stmpe>; + status = "disabled"; + + touchscreen { + compatible = "st,stmpe-ts"; + st,sample-time = <4>; + st,mod-12b = <1>; + st,ref-sel = <0>; + st,adc-freq = <1>; + st,ave-ctrl = <1>; + st,touch-det-delay = <2>; + st,settling = <2>; + st,fraction-z = <7>; + st,i-drive = <1>; + touchscreen-inverted-x = <1>; + touchscreen-inverted-y = <1>; + }; + }; + + i2c_rtc: rtc@68 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_rtc_int>; + compatible = "microcrystal,rv4162"; + reg = <0x68>; + interrupt-parent = <&gpio5>; + interrupts = <1 IRQ_TYPE_LEVEL_LOW>; + status = "disabled"; + }; +}; + +&mdio { + ethphy1: ethernet-phy@2 { + reg = <2>; + micrel,led-mode = <1>; + clocks = <&clks IMX6UL_CLK_ENET2_REF>; + clock-names = "rmii-ref"; + }; +}; + +&pwm3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm3>; + status = "disabled"; +}; + +&sai2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sai2>; + assigned-clocks = <&clks IMX6UL_CLK_SAI2_SEL>, + <&clks IMX6UL_CLK_SAI2>; + assigned-clock-parents = <&clks IMX6UL_CLK_PLL4_AUDIO_DIV>; + assigned-clock-rates = <0>, <19200000>; + fsl,sai-mclk-direction-output; + status = "disabled"; +}; + +&uart5 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart5>; + uart-has-rtscts; + status = "disabled"; +}; + +&usbotg1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb_otg1_id>; + dr_mode = "otg"; + status = "disabled"; +}; + +&usbotg2 { + dr_mode = "host"; + disable-over-current; + status = "disabled"; +}; + +&usdhc1 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc1>; + pinctrl-1 = <&pinctrl_usdhc1_100mhz>; + pinctrl-2 = <&pinctrl_usdhc1_200mhz>; + cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>; + no-1-8-v; + keep-power-in-suspend; + wakeup-source; + status = "disabled"; +}; + +&iomuxc { + pinctrl_adc1: adc1grp { + fsl,pins = < + MX6UL_PAD_GPIO1_IO03__GPIO1_IO03 0xb0 + >; + }; + + pinctrl_enet2: enet2grp { + fsl,pins = < + MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN 0x1b0b0 + MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER 0x1b0b0 + MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00 0x1b0b0 + MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01 0x1b0b0 + MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN 0x1b0b0 + MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00 0x1b0b0 + MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01 0x1b0b0 + MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 0x4001b031 + >; + }; + + pinctrl_flexcan1: flexcan1 { + fsl,pins = < + MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX 0x0b0b0 + MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX 0x0b0b0 + >; + }; + + princtrl_flexcan1_en: flexcan1engrp { + fsl,pins = < + MX6UL_PAD_SNVS_TAMPER2__GPIO5_IO02 0x17059 + >; + }; + + pinctrl_pwm3: pwm3grp { + fsl,pins = < + MX6UL_PAD_GPIO1_IO04__PWM3_OUT 0x0b0b0 + >; + }; + + pinctrl_rtc_int: rtcintgrp { + fsl,pins = < + MX6UL_PAD_SNVS_TAMPER1__GPIO5_IO01 0x17059 + >; + }; + + pinctrl_sai2: sai2grp { + fsl,pins = < + MX6UL_PAD_JTAG_TDI__SAI2_TX_BCLK 0x17088 + MX6UL_PAD_JTAG_TDO__SAI2_TX_SYNC 0x17088 + MX6UL_PAD_JTAG_TRST_B__SAI2_TX_DATA 0x11088 + MX6UL_PAD_JTAG_TCK__SAI2_RX_DATA 0x11088 + MX6UL_PAD_JTAG_TMS__SAI2_MCLK 0x17088 + >; + }; + + pinctrl_stmpe: stmpegrp { + fsl,pins = < + MX6UL_PAD_SNVS_TAMPER3__GPIO5_IO03 0x17059 + >; + }; + + pinctrl_uart5: uart5grp { + fsl,pins = < + MX6UL_PAD_UART5_TX_DATA__UART5_DCE_TX 0x1b0b1 + MX6UL_PAD_UART5_RX_DATA__UART5_DCE_RX 0x1b0b1 + MX6UL_PAD_GPIO1_IO08__UART5_DCE_RTS 0x1b0b1 + MX6UL_PAD_GPIO1_IO09__UART5_DCE_CTS 0x1b0b1 + >; + }; + + pinctrl_usb_otg1_id: usbotg1idgrp { + fsl,pins = < + MX6UL_PAD_GPIO1_IO00__ANATOP_OTG1_ID 0x17059 + >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x17059 + MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x10059 + MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x17059 + MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x17059 + MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x17059 + MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x17059 + MX6UL_PAD_UART1_RTS_B__GPIO1_IO19 0x17059 + >; + }; + + pinctrl_usdhc1_100mhz: usdhc1grp100mhz { + fsl,pins = < + MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x170b9 + MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x100b9 + MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x170b9 + MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x170b9 + MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x170b9 + MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x170b9 + >; + }; + + pinctrl_usdhc1_200mhz: usdhc1grp200mhz { + fsl,pins = < + MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x170f9 + MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x100f9 + MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x170f9 + MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x170f9 + MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x170f9 + MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x170f9 + >; + }; +}; -- 2.20.1 ^ permalink raw reply related [flat|nested] 10+ messages in thread
* Re: [PATCH v3 2/2] ARM: dts: imx6: Add support for Phytec phyBOARD i.MX6UL Segin 2019-01-21 9:57 ` Martyn Welch @ 2019-01-21 10:33 ` Fabio Estevam -1 siblings, 0 replies; 10+ messages in thread From: Fabio Estevam @ 2019-01-21 10:33 UTC (permalink / raw) To: Martyn Welch Cc: Mark Rutland, open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS, Stefan Riedmüller, Sascha Hauer, linux-kernel, Rob Herring, NXP Linux Team, Pengutronix Kernel Team, Christian Hemp, Fabio Estevam, Shawn Guo, moderated list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE On Mon, Jan 21, 2019 at 7:57 AM Martyn Welch <martyn.welch@collabora.com> wrote: > > The Phytec phyBOARD Segin is i.MX6 based SBC, available with either an > i.MX6UL or i.MX6ULL SOM and various add-on boards. > > The following adds support for the "Full Featured" version of the Segin, > which is provided with the i.MX6UL SOM and the PEB-EVAL-01 evaluation > module. > > Its hardware specifications are: > > * 512MB DDR3 memory > * 512MB NAND flash > * Dual 10/100 Ethernet > * USB Host and USB OTG > * RS232 > * MicroSD external storage > * Audio, RS232, I2C, SPI, CAN headers > * Further I/O options via A/V and Expansion headers > > Signed-off-by: Martyn Welch <martyn.welch@collabora.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH v3 2/2] ARM: dts: imx6: Add support for Phytec phyBOARD i.MX6UL Segin @ 2019-01-21 10:33 ` Fabio Estevam 0 siblings, 0 replies; 10+ messages in thread From: Fabio Estevam @ 2019-01-21 10:33 UTC (permalink / raw) To: Martyn Welch Cc: Shawn Guo, Sascha Hauer, Rob Herring, Mark Rutland, open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS, Stefan Riedmüller, linux-kernel, NXP Linux Team, Pengutronix Kernel Team, Christian Hemp, Fabio Estevam, moderated list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE On Mon, Jan 21, 2019 at 7:57 AM Martyn Welch <martyn.welch@collabora.com> wrote: > > The Phytec phyBOARD Segin is i.MX6 based SBC, available with either an > i.MX6UL or i.MX6ULL SOM and various add-on boards. > > The following adds support for the "Full Featured" version of the Segin, > which is provided with the i.MX6UL SOM and the PEB-EVAL-01 evaluation > module. > > Its hardware specifications are: > > * 512MB DDR3 memory > * 512MB NAND flash > * Dual 10/100 Ethernet > * USB Host and USB OTG > * RS232 > * MicroSD external storage > * Audio, RS232, I2C, SPI, CAN headers > * Further I/O options via A/V and Expansion headers > > Signed-off-by: Martyn Welch <martyn.welch@collabora.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> ^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH v3 1/2] dt-bindings: Add vendor prefix for Catalyst Semiconductor 2019-01-21 9:57 ` Martyn Welch @ 2019-01-21 10:04 ` Andreas Färber -1 siblings, 0 replies; 10+ messages in thread From: Andreas Färber @ 2019-01-21 10:04 UTC (permalink / raw) To: Martyn Welch Cc: Mark Rutland, devicetree, Stefan Riedmüller, Rob Herring, Martin Blumenstingl, Kevin Hilman, Sascha Hauer, linux-kernel, Johan Hovold, Rob Herring, NXP Linux Team, Pengutronix Kernel Team, Christian Hemp, Fabio Estevam, Thierry Reding, Shawn Guo, linux-arm-kernel Am 21.01.19 um 10:57 schrieb Martyn Welch: > Add vendor prefix "catalyst" for Catalyst Semiconductor which is > already in use but undocumented. > > Signed-off-by: Martyn Welch <martyn.welch@collabora.com> > Reviewed-by: Rob Herring <robh@kernel.org> Reviewed-by: Andreas Färber <afaerber@suse.de> Thanks, Andreas -- SUSE Linux GmbH, Maxfeldstr. 5, 90409 Nürnberg, Germany GF: Felix Imendörffer, Jane Smithard, Graham Norton HRB 21284 (AG Nürnberg) _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH v3 1/2] dt-bindings: Add vendor prefix for Catalyst Semiconductor @ 2019-01-21 10:04 ` Andreas Färber 0 siblings, 0 replies; 10+ messages in thread From: Andreas Färber @ 2019-01-21 10:04 UTC (permalink / raw) To: Martyn Welch Cc: Shawn Guo, Sascha Hauer, Rob Herring, Mark Rutland, Fabio Estevam, devicetree, Christian Hemp, Stefan Riedmüller, Pengutronix Kernel Team, linux-arm-kernel, NXP Linux Team, Rob Herring, Martin Blumenstingl, Thierry Reding, linux-kernel, Kevin Hilman, Johan Hovold Am 21.01.19 um 10:57 schrieb Martyn Welch: > Add vendor prefix "catalyst" for Catalyst Semiconductor which is > already in use but undocumented. > > Signed-off-by: Martyn Welch <martyn.welch@collabora.com> > Reviewed-by: Rob Herring <robh@kernel.org> Reviewed-by: Andreas Färber <afaerber@suse.de> Thanks, Andreas -- SUSE Linux GmbH, Maxfeldstr. 5, 90409 Nürnberg, Germany GF: Felix Imendörffer, Jane Smithard, Graham Norton HRB 21284 (AG Nürnberg) ^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH v3 1/2] dt-bindings: Add vendor prefix for Catalyst Semiconductor 2019-01-21 9:57 ` Martyn Welch @ 2019-01-22 5:57 ` Shawn Guo -1 siblings, 0 replies; 10+ messages in thread From: Shawn Guo @ 2019-01-22 5:57 UTC (permalink / raw) To: Martyn Welch Cc: Mark Rutland, devicetree, Stefan Riedmüller, Rob Herring, Martin Blumenstingl, Kevin Hilman, Sascha Hauer, linux-kernel, Johan Hovold, Rob Herring, NXP Linux Team, Pengutronix Kernel Team, Christian Hemp, Fabio Estevam, Thierry Reding, Andreas Färber, linux-arm-kernel On Mon, Jan 21, 2019 at 09:57:04AM +0000, Martyn Welch wrote: > Add vendor prefix "catalyst" for Catalyst Semiconductor which is > already in use but undocumented. > > Signed-off-by: Martyn Welch <martyn.welch@collabora.com> > Reviewed-by: Rob Herring <robh@kernel.org> Applied both, thanks. _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH v3 1/2] dt-bindings: Add vendor prefix for Catalyst Semiconductor @ 2019-01-22 5:57 ` Shawn Guo 0 siblings, 0 replies; 10+ messages in thread From: Shawn Guo @ 2019-01-22 5:57 UTC (permalink / raw) To: Martyn Welch Cc: Sascha Hauer, Rob Herring, Mark Rutland, Fabio Estevam, devicetree, Christian Hemp, Stefan Riedmüller, Pengutronix Kernel Team, linux-arm-kernel, NXP Linux Team, Rob Herring, Martin Blumenstingl, Thierry Reding, linux-kernel, Kevin Hilman, Johan Hovold, Andreas Färber On Mon, Jan 21, 2019 at 09:57:04AM +0000, Martyn Welch wrote: > Add vendor prefix "catalyst" for Catalyst Semiconductor which is > already in use but undocumented. > > Signed-off-by: Martyn Welch <martyn.welch@collabora.com> > Reviewed-by: Rob Herring <robh@kernel.org> Applied both, thanks. ^ permalink raw reply [flat|nested] 10+ messages in thread
end of thread, other threads:[~2019-01-22 5:58 UTC | newest] Thread overview: 10+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2019-01-21 9:57 [PATCH v3 1/2] dt-bindings: Add vendor prefix for Catalyst Semiconductor Martyn Welch 2019-01-21 9:57 ` Martyn Welch 2019-01-21 9:57 ` [PATCH v3 2/2] ARM: dts: imx6: Add support for Phytec phyBOARD i.MX6UL Segin Martyn Welch 2019-01-21 9:57 ` Martyn Welch 2019-01-21 10:33 ` Fabio Estevam 2019-01-21 10:33 ` Fabio Estevam 2019-01-21 10:04 ` [PATCH v3 1/2] dt-bindings: Add vendor prefix for Catalyst Semiconductor Andreas Färber 2019-01-21 10:04 ` Andreas Färber 2019-01-22 5:57 ` Shawn Guo 2019-01-22 5:57 ` Shawn Guo
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.