From: Andrew Lunn <andrew@lunn.ch>
To: John David Anglin <dave.anglin@bell.net>
Cc: Russell King <linux@arm.linux.org.uk>,
Vivien Didelot <vivien.didelot@savoirfairelinux.com>,
Florian Fainelli <f.fainelli@gmail.com>,
netdev@vger.kernel.org
Subject: Re: [PATCH] net: phylink: dsa: mv88e6xxx: Revise irq setup ordering
Date: Mon, 4 Feb 2019 20:35:18 +0100 [thread overview]
Message-ID: <20190204193518.GE24989@lunn.ch> (raw)
In-Reply-To: <53b49df8-53ed-704f-9197-230b18d83090@bell.net>
On Mon, Feb 04, 2019 at 01:37:13PM -0500, John David Anglin wrote:
> This change fixes a race condition in the setup of hardware irqs and the
> code enabling PHY link
> detection.
>
> This was observed on the espressobin board where the GPIO interrupt
> controller only supports edge
> interrupts. If the INTn output pin goes low before the GPIO interrupt
> is enabled, PHY link interrupts
> are not detected.
Hi David
Please break this up into two patches.
Masking interrupts in the setup code before enabling the interrupt i'm
happy with.
The change to the interrupt handler i'm pretty sure is wrong. You have
to accept with edge interrupts you are going to loose interrupts.
Andrew
next prev parent reply other threads:[~2019-02-04 19:35 UTC|newest]
Thread overview: 52+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-01-22 19:16 net: phylink: dsa: mv88e6xxx: flaky link detection on switch ports with internal PHYs John David Anglin
2019-01-22 20:28 ` Andrew Lunn
2019-01-22 21:40 ` John David Anglin
2019-01-22 22:36 ` Andrew Lunn
2019-01-22 23:52 ` John David Anglin
2019-01-23 0:11 ` John David Anglin
2019-01-23 0:22 ` Andrew Lunn
2019-01-25 16:30 ` John David Anglin
2019-01-25 16:48 ` Russell King - ARM Linux admin
2019-01-25 18:38 ` John David Anglin
2019-01-30 17:08 ` John David Anglin
2019-01-30 17:28 ` Andrew Lunn
2019-01-30 19:01 ` John David Anglin
2019-01-30 19:09 ` Andrew Lunn
2019-01-30 22:24 ` John David Anglin
2019-01-30 22:38 ` Andrew Lunn
2019-01-31 1:27 ` John David Anglin
2019-01-31 17:27 ` John David Anglin
2019-02-04 18:37 ` [PATCH] net: phylink: dsa: mv88e6xxx: Revise irq setup ordering John David Anglin
2019-02-04 19:35 ` Andrew Lunn [this message]
2019-02-04 19:52 ` John David Anglin
2019-02-04 20:19 ` Andrew Lunn
2019-02-04 21:38 ` John David Anglin
2019-02-04 22:47 ` Andrew Lunn
2019-02-04 21:59 ` [PATCH v2] net: " John David Anglin
2019-02-04 23:14 ` Andrew Lunn
2019-02-05 0:38 ` John David Anglin
2019-02-05 2:21 ` Andrew Lunn
2019-02-05 19:20 ` John David Anglin
2019-02-05 19:54 ` Andrew Lunn
2019-02-05 18:37 ` David Miller
2019-02-11 18:40 ` [PATCH net] dsa: mv88e6xxx: Ensure all pending interrupts are handled prior to exit John David Anglin
2019-02-11 23:33 ` Andrew Lunn
2019-02-12 0:57 ` John David Anglin
2019-02-12 1:21 ` Andrew Lunn
2019-02-12 3:58 ` Andrew Lunn
2019-02-12 6:51 ` Heiner Kallweit
2019-02-12 12:56 ` Andrew Lunn
2019-02-12 18:42 ` Heiner Kallweit
2019-02-12 20:09 ` John David Anglin
2019-02-12 16:30 ` Russell King - ARM Linux admin
2019-02-12 20:11 ` Heiner Kallweit
2019-02-12 20:54 ` Heiner Kallweit
2019-02-12 22:55 ` Russell King - ARM Linux admin
2019-02-14 2:07 ` Andrew Lunn
2019-02-14 4:47 ` David Miller
2019-02-14 4:50 ` Andrew Lunn
2019-02-14 15:27 ` David Miller
2019-01-22 23:12 ` net: phylink: dsa: mv88e6xxx: flaky link detection on switch ports with internal PHYs Andrew Lunn
2019-01-22 23:48 ` John David Anglin
2019-01-23 0:00 ` John David Anglin
2019-01-23 0:04 ` Florian Fainelli
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190204193518.GE24989@lunn.ch \
--to=andrew@lunn.ch \
--cc=dave.anglin@bell.net \
--cc=f.fainelli@gmail.com \
--cc=linux@arm.linux.org.uk \
--cc=netdev@vger.kernel.org \
--cc=vivien.didelot@savoirfairelinux.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.